Made *ocp2scp_usb_phy_phy_48m* as the main_clk for ocp2scp.
Since this ocp2scp module does not have any fck but does have a
single opt_clock, it is added as the main_clk for ocp2scp. Also
removed phy_48m as the optional clock since it is now made as the
main clock. By this the driver need not enable/disable phy_48m clk
separately and runtime_get/runtime_put will take care of that.
Cc: Benoît Cousson <b-cousson@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
ocp2scp_usb_phy was missing the address space data and thus
the sysconfig was not populated either.
The usb_host_hs address space was wrong.
Fix both of them and add the missing sysconfig entry.
Reported-by: Kishon Vijay Abraham <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
SAD2D stands for the die to die interface, and is used for communicating
with the optional stacked modem. This hwmod is added in preparation for
the d2d_idle move from pm34xx.c to hwmod data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: SAD2D presumably doesn't exist on non-OMAP34xx/OMAP36xx,
so only add it to the OMAP34xx/OMAP36xx lists]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For a reset sequence to complete cleanly, a module needs its
associated clocks to be enabled, otherwise the timeout check
in prcm code can print a false failure (failed to hardreset)
that occurs because the clocks aren't powered ON and the status
bit checked can't transition without them.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some IP blocks might not be using/controlling more than one
reset line, this check loosens the restriction to fully use
hwmod framework for those drivers.
E.g.: ipu has reset lines: mmu_cache, cpu0 and cpu1.
- As of now cpu1 is not used and hence (with previous check) the
IP block isn't fully enabled by hwmod code.
- Usually ipu and dsp processors configure their mmu module first
and then enable the processors, this involves:
* Deasserting mmu reset line, and enabling the module.
* Deasserting cpu0 reset line, and enabling the processor.
The ones portrayed in this example are controlled through
rproc_fw_boot in drivers/remoteproc/remoteproc_core.c
While at it, prevent _omap4_module_disable if all the hardreset
lines on an IP block are not under reset.
This will allow the driver to:
a. Deassert the reset line.
b. Enable the hwmod through runtime PM default callbacks.
c. Do its usecase.
d. Disable hwmod through runtime PM.
e. Assert the reset line.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4 most modules/hwmods support module level context status. On
OMAP3 and earlier, we relied on the power domain level context status.
Identify all modules that don't support 'context_offs' by adding a
flag bit, HWMOD_OMAP4_NO_CONTEXT_LOSS_BIT. Rest have a valid
'context_offs' populated in .prcm structure already.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: add flag bit rather than overloading .context_offs;
update changelog message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently hwmod only provides the offset for the context lose
register, and if we attempt to share the same register between two or
more hwmods, the resulting context loss counts get wrong. Thus, we
need a way to specify which bits are used for the context loss
information for each. This is accomplished by adding a new field to
the omap4 prcm struct, 'lostcontext_mask', which specifies a bit-mask
to use for filtering the register.
Mark the affected hwmods appropriately. 'l4_abe' hwmod uses the
LOSTMEM_AESSMEM bit of RM_ABE_AESS_CONTEXT register, as l4_abe doesn't
have its own dedicated register for this purpose. This register is
shared with 'aess' hwmod, thus both hwmods must also specify which
bits of the register are used for them.
This patch only adds the hwmod data, but a future patch should add
code support such that only the specified bits are read and cleared by
the context lose counter update code. If a hwmod doesn't specify
'lostcontext_mask' (default behavior), the whole contents of the
context register should be used without any filtering.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: updated to apply after conversion to use flag bit for
missing module context-loss register; combined data and code patches;
dropped code change due to serial driver breakage]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4, there is no support to read previous logic state
or previous memory state achieved when a power domain transitions
to RET. Instead there are module level context registers.
In order to support the powerdomain level logic/mem_off_counters
on OMAP4, instead use the previous power state achieved (RET) and
the *programmed* logic/mem RET state to derive if a powerdomain lost
logic or did not.
If the powerdomain is programmed to enter RET state and lose logic
in RET state, knowing that the powerdomain entered RET is good enough
to derive that the logic was lost as well, in such cases.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: removed dependency on functional power state series for now;
bumped copyright date]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The decision was made a few months ago to allow struct omap_hwmod
records and struct clk records to omit clockdomain information if the
clockdomain is not software-controllable. See for example commit
868c157df9 ("ARM: OMAP2+: hwmod: remove
prm_clkdm, cm_clkdm; allow hwmods to have no clockdomain").
So convert an existing pr_warning() to a pr_debug() (regarding missing
clockdomains in clocks), and add a pr_debug() for missing hwmod
clockdomains. It's still useful to enable these messages for
debugging, since missing clockdomains can cause hard-to-debug problems
with power management; see for example commit
6c4a057bff ("ARM: OMAP4: clock data:
Force a DPLL clkdm/pwrdm ON before a relock").
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
We're no longer requiring struct omap_hwmod records to contain a
clockdomain. So we shouldn't return -EINVAL any more from
_omap4_wait_target_disable() or _omap4_wait_target_ready() if there's
no clockdomain defined, since that just gets passed back to the
caller. This can result in pointless warnings under the relaxed data
format.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
This API is meant to be an interface to hwmod assert/deassert
function, omap devices can call them through their platform data to
control their reset lines, they are expected to know the name of the
reset line they are trying to control.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
[paul@pwsan.com: tweaked some documentation; fixed CodingStyle issue]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Several hwmod function prototypes appear to not have an implementation
because the corresponding functions were removed or renamed.
Those prototypes are unneeded anymore - remove them.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[paul@pwsan.com: tweaked subject]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UyqO
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-am33xx-for-v3.7' into test_v3.6-rc6_ocb3.7_cff3.7_odaf3.7
From Paul Walmsley <paul@pwsan.com>:
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=omEP
-----END PGP SIGNATURE-----
Merge tag 'cleanup-fixes-for-v3.7' into test_v3.6-rc6_ocb3.7_cff3.7_odaf3.7
These fixes are needed to fix non-omap build breakage for
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.
These changes fix some of the more meaningful warnings that smatch
returns for the OMAP subarch code, and unwraps strings that are
wrapped at the 80-column boundary, to conform with the current
practice.
Basic build, boot, and PM logs are available here:
http://www.pwsan.com/omap/testlogs/warnings_a_cleanup_3.7/20120912025927/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ythb
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-b-for-3.7' into test_v3.6-rc6_ocb3.7_cff3.7_odaf3.7
smatch and string-wrapping cleanups for the OMAP subarch code.
These changes fix some of the more meaningful warnings that smatch
returns for the OMAP subarch code, and unwraps strings that are
wrapped at the 80-column boundary, to conform with the current
practice.
Basic build, boot, and PM logs are available here:
http://www.pwsan.com/omap/testlogs/warnings_a_cleanup_3.7/20120912025927/
The new common clk framework includes basic definitions for mux and
divider clocks. These definitions depend on shift and width values
instead of the pre-computed masks that the OMAP/AM33XX clk framework
has traditionally used when accessing the register to control the
mux or divisor.
To ease this transition the masks are left intact and
the width field is simply added alongside the shift and mask data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The new common clk framework includes basic definitions for mux and
divider clocks. These definitions depend on shift and width values
instead of the pre-computed masks that the OMAP clk framework has
traditionally used when accessing the register to control the mux or
divisor.
To ease this transition the masks are left intact and the width field is
simply added alongside the shift and mask data.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
While we move to Common Clk Framework (CCF), direct deferencing of struct
clk wouldn't be possible anymore. Hence get rid of all such instances
in the current clock code and use macros/helpers similar to the ones that
are provided by CCF.
While here also concatenate some strings split across multiple lines
which seem to be needed anyway.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: simplified some compound expressions; reformatted some
messages]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>
Moving to Common clk framework for OMAP would mean we no longer use
internal lookup mechanism like omap_clk_get_by_name().
get rid of all its usage mostly from hwmod and omap_device
code.
Moving to clk_get() also means the respective platforms
need the clkdev tables updated with an entry for all clocks
used by hwmod to have clock name same as the alias.
Based on original changes from Mike Turquette.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
[paul@pwsan.com: removed IS_ERR_OR_NULL() conversion (rmk comment);
restricted omap_96m_alwon_fck_3630 to OMAP36xx; added missing AM35xx
clock aliases for emac_fck, emac_ick, vpfe_ick, vpfe_fck; added
aliases rng_ick and several emulation clocks]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
As part of Common Clk Framework (CCF) the clk_enable() operation
was split into a clk_prepare() which could sleep, and a clk_enable()
which should never sleep. Similarly the clk_disable() was
split into clk_disable() and clk_unprepare(). This was
needed to handle complex cases where in a clk gate/ungate
would require a slow and a fast part to be implemented.
None of the clocks below seem to be in the 'complex' clocks
category and are just simple clocks which are enabled/disabled
through simple register writes.
Most of the instances also seem to be called in non-atomic
context which means its safe to move all of those from
using a clk_enable() to clk_prepare_enable() and clk_disable() to
clk_disable_unprepare().
For some others, mainly the ones handled through the hwmod framework
there is a possibility that they get called in either an atomic
or a non-atomic context.
The way these get handled below work only as long as clk_prepare
is implemented as a no-op (which is the case today) since this gets
called very early at boot while most subsystems are unavailable.
Hence these are marked with a *HACK* comment, which says we need
to re-visit these once we start doing something meaningful with
clk_prepare/clk_unprepare like doing voltage scaling or something
that involves i2c.
This is in preparation of OMAP moving to CCF.
Based on initial changes from Mike Turquette.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For OMAP4, the dmtimers are located in the Wake-up, ABE and Peripheral (PER)
power domains. Hence, when the dmtimer is configured to use the "timer_sys_ck"
as its functional clock the actual clock used is different depending on whether
the clock is in the Wake-up, ABE or PER domain. So when we look-up the dmtimer's
"timer_sys_ck" we need to specify the timer device name as well as clock alias
to find the right clock.
Currently, the device names for the timers have the format "omap_timer.X" where
X is the timer instance number. When using to device tree, the format of the
device name created by device-tree is different and has the format
"<reg-address>.<device-name>" (this is assuming that the device-tree "reg"
property is specified). This causes the look-up for the OMAP4 "timer_sys_ck" to
fail. To fix this add new timer clock alias for using device-tree.
Please note that adding a 2nd set of clock aliases for the same clocks to only
temporary until device-tree migration is complete. Then we can remove the legacy
aliases. Hence, I have marked the legacy aliases with a "TODO" to remove them.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add AM335x cpu0 clock entry to the corresponding clock data file. This
is useful in getting the correct mpu clock pointer to change the cpu
frequency in cpufreq driver.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
[paul@pwsan.com: changed patch subject]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
These clkdev aliases should make it possible to remove the
cpu_is_omap*() calls and the omap_device*() call from
drivers/cpufreq/omap-cpufreq.c during the next merge window. Those
are interfering with multi-subarch ARM kernels.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
The platform device name "usbhs_tll" is added for the functional,
interface and channel clocks of the TLL module.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In commit c59b537 (ARM: OMAP2+: Simplify dmtimer clock aliases) new clock
aliases were added for OMAP2+ devices. For OMAP2420, I incorrectly set the
clock flag as CK_243X instead of CK_242X. This did not introduce a regression
as the clock flags are not checked for OMAP2 devices. This also explains why
I did not catch this when testing on OMAP2420.
Fix the clock flags for these aliases for correctness.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The file is currently called 'clock3xxx_data.c', so this comment is
out of date.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
[paul@pwsan.com: wrote changelog]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UyqO
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-am33xx-for-v3.7' into test_v3.6-rc6_cff3.7_odaf3.7
From Paul Walmsley <paul@pwsan.com>:
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=omEP
-----END PGP SIGNATURE-----
Merge tag 'cleanup-fixes-for-v3.7' into test_v3.6-rc6_cff3.7_odaf3.7
These fixes are needed to fix non-omap build breakage for
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.
Merge of the LED related changes with omap sparse IRQ and
hardware.h related changes causes a build issue otherwise:
arch/arm/mach-omap1/board-h2.c:319: error: implicit declaration of function ‘OMAP_MPUIO’
arch/arm/mach-omap1/board-h2.c:319: error: initializer element is not constant
arch/arm/mach-omap1/board-h2.c:319: error: (near initialization for ‘h2_gpio_led_pins[1].gpio’)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable pinctrl dummy states for all OMAP platforms that don't
populate DT. This allows drivers to be converted to pinctrl
and not generate new warnings on platforms that do not provide
pinctrl data. These platforms already have pinmuxes configured
before the drivers probe.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7d7e1eba (ARM: OMAP2+: Prepare for irqs.h removal) broke
compile for non-omap as include plat/cpu.h was added. This header
was indirectly included earlier when SPARSE_IRQ was not set, but
does not exist on most platforms.
Fix the problem by removing the cpu_is_omap usage that should
not exist in drivers at all. We can do this by adding proper
clock aliases for the twl-core.c drivers, and drop separate
handling for cases when clock framework is not available as
the behaviour will stay the same.
Note that we need to add a platform device to avoid using the
i2c provided names that may be different on various omaps.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull one more DMA-mapping fix from Marek Szyprowski:
"This patch fixes very subtle bug (typical off-by-one error) which
might appear in very rare circumstances."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
arm: mm: fix DMA pool affiliation check
Pull perf fixes from Ingo Molnar:
"This tree includes various fixes"
Ingo really needs to improve on the whole "explain git pull" part.
"Various fixes" indeed.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/hwpb: Invoke __perf_event_disable() if interrupts are already disabled
perf/x86: Enable Intel Cedarview Atom suppport
perf_event: Switch to internal refcount, fix race with close()
oprofile, s390: Fix uninitialized memory access when writing to oprofilefs
perf/x86: Fix microcode revision check for SNB-PEBS
- A set of OMAP fixes, about half of them PM/clock related, the rest
scattered over the platform code but all small and targeted to real bugs.
- Two small i.MX fixes for SSI device clock setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQUYT/AAoJEIwa5zzehBx3m7UQAIW17Uzqfw+5KGhh0UMSVPuq
XQznJRadYAlLwRK8O/K6aJ1TnHa21BrVSa8F2y9KHthM7YhGplzcluNMUtOGRCsM
HUceddSqy7DQp7CcwAJSb+VHd5I1d7iVbEp3oU3BD0OGQM6J0ddfUUo6a2fnpETV
E6JpHhllB7NXVq8Bx5gy/M9idaUdjxNyAEe62pjmVmvK2wi1l1323wiMYpcU8i9t
wBPHRDvYAHLju1j9qVZQa8gZ6EEGqqCaSIbCmX3omuuFFkmZHRHJSqv428LKa8lN
i8CfknJJTVDt+9RojJ+P4VuAMr+PWdZmL6cWS1dVz4KZsnG7eyfD3e4GczCd7UEd
YKLLh/0B1Oo+dH+6kXK8RscC5P38zRxT3fmpZ6R7yePGuYQJHkuMaBq8Lg46blJR
m+bTWrGoZByO1XCmebh2lCfu8PsuuksuTwr7Lu3ekDhZF5vDr9KFlmyts4lLTSaW
zjWjoAJa8334w1rRRnR4eWllFRx62VJWkZiQU5jlV6V01/FedLB0/RxPMT6RRDiw
DoCLPWIPe0ft2qgSTrPcbIVqcQcpzwVsPKq8OHcYUA6cILg7Q5Rix/V1FbVlw1ac
ob63CBSA7vxoN5PlErLO7eAluEmQjM45drQ5d6THdkihM/uzZ44VJ/pwW67ZmahW
jtH+5XOSNVsZU0dk/9dY
=y6Db
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc bug fixes from Olof Johansson:
- A set of OMAP fixes, about half of them PM/clock related, the rest
scattered over the platform code but all small and targeted to real
bugs.
- Two small i.MX fixes for SSI device clock setup.
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: clk-imx35: Fix SSI clock registration
ARM: clk-imx25: Fix SSI clock registration
ARM: OMAP4: Fix array size for irq_target_cpu
ARM: OMAP4: hwmod data: temporarily comment out data for the sl2if IP block
ARM: OMAP: hwmod code: Disable module when hwmod enable fails
ARM: OMAP3: hwmod data: fix iva2 reset info
ARM: OMAP3xxx: clockdomain: fix software supervised wakeup/sleep
ARM: OMAP2+: am33xx: Fix the timer fck clock naming convention
ARM: OMAP: Config fix for omap3-touchbook board
ARM: OMAP: sram: skip the first 16K on OMAP3 HS
ARM: OMAP: sram: fix OMAP4 errata handling
ARM: OMAP: timer: obey the !CONFIG_OMAP_32K_TIMER
should now boot on mainline after this is applied, according to
Vaibhav.
This second version includes trailing commas at the end of structure
records at Tony's request. It also adds a OMAP_INTC_START macro
expansion to each IRQ number to make the sparseirq conversion easier.
Basic build, boot, and PM test transcripts are here:
http://www.pwsan.com/omap/testlogs/am33xx_hwmod_clock_devel_3.7/20120912165952/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yRjp
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-a2-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into devel-am33xx
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
This second version includes trailing commas at the end of structure
records at Tony's request. It also adds a OMAP_INTC_START macro
expansion to each IRQ number to make the sparseirq conversion easier.
Basic build, boot, and PM test transcripts are here:
http://www.pwsan.com/omap/testlogs/am33xx_hwmod_clock_devel_3.7/20120912165952/
There's no need to have these in plat-omap any longer. Note that these
could eventually be made local to mach-omap1 instead of being in mach.
But to do that, at least various driver access using omap7xxx.h registers
needs to be fixed first.
Cc: spi-devel-general@lists.sourceforge.net
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These can now be moved to be local headers in mach-omap2.
Note that this patch removes arch/arm/plat-omap/devices.c as it
will get removed anyways with Paul Walmsley's patch
"ARM: OMAP: split OMAP1, OMAP2+ RNG device registration".
Signed-off-by: Tony Lindgren <tony@atomide.com>
As the plat and mach includes need to disappear for single zImage work,
we need to remove plat/hardware.h.
Do this by splitting plat/hardware.h into omap1 and omap2+ specific files.
The old plat/hardware.h already has omap1 only defines, so it gets moved
to mach/hardware.h for omap1. For omap2+, we use the local soc.h
that for now just includes the related SoC headers to keep this patch more
readable.
Note that the local soc.h still includes plat/cpu.h that can be dealt
with in later patches. Let's also include plat/serial.h from common.h for
all the board-*.c files. This allows making the include files local later
on without patching these files again.
Note that only minimal changes are done in this patch for the
drivers/watchdog/omap_wdt.c driver to keep things compiling. Further
patches are needed to eventually remove cpu_is_omap usage in the drivers.
Also only minimal changes are done to sound/soc/omap/* to remove the
unneeded includes and to define OMAP44XX_MCPDM_L3_BASE locally so there's
no need to include omap44xx.h.
While at it, also sort some of the includes in the standard way.
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove hardcoded IRQs in irqs.h and related files as these
are no longer needed.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As the interrupts should only be defined in the platform_data, and
eventually coming from device tree, there's no need to define them
in header files.
Let's remove the hardcoded references to irqs.h and fix up the includes
so we don't rely on headers included in irqs.h. Note that we're
defining OMAP_INTC_START as 0 to the interrupts. This will be needed
when we enable SPARSE_IRQ. For some drivers we need to add
#include <plat/cpu.h> for now until these drivers are fixed to
remove cpu_is_omapxxxx() usage.
While at it, sort som of the includes the standard way, and add
the trailing commas where they are missing in the related data
structures.
Note that for drivers/staging/tidspbridge we just define things
locally.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we can remove includes of plat/gpio.h which won't work
with the single zImage support.
Note that we also remove the cpu_class_is_omap2() check
in gpio-omap.c as the drivers should not call it as we need to
make it local to arch/arm/mach-omap2 for single zImage support.
While at it, arrange the related includes in the standard way.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mtd@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can't use hardcoded interrupts for SPARSE_IRQ, and can replace
the hardcoded gpio_base with twl_gpiochip.base after it's been
allocated.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is no longer needed and assumes a fixed IRQ number
that won't work with SPARSE_IRQ.
Acked-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
