This allows maximum flexibility for configuring the direct GPIO based
interrupts.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In order for MFD drivers to fetch their cell pointer but also their
platform data one, an mfd cell pointer is added to the platform_device
structure.
That allows all MFD sub devices drivers to be MFD agnostic, unless
they really need to access their MFD cell data. Most of them don't,
especially the ones for IPs used by both MFD and non MFD SoCs.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (26 commits)
mmc: SDHI should depend on SUPERH || ARCH_SHMOBILE
mmc: tmio_mmc: Move some defines into a shared header
mmc: tmio: support aggressive clock gating
mmc: tmio: fix power-mode interpretation
mmc: tmio: remove work-around for unmasked SDIO interrupts
sh: fix SDHI IO address-range
ARM: mach-shmobile: fix SDHI IO address-range
mmc: tmio: only access registers above 0xff, if available
mfd: remove now redundant sh_mobile_sdhi.h header
sh: convert boards to use linux/mmc/sh_mobile_sdhi.h
ARM: mach-shmobile: convert boards to use linux/mmc/sh_mobile_sdhi.h
mmc: tmio: convert the SDHI MMC driver from MFD to a platform driver
sh: ecovec: use the CONFIG_MMC_TMIO symbols instead of MFD
mmc: tmio: split core functionality, DMA and MFD glue
mmc: tmio: use PIO for short transfers
mmc: tmio-mmc: Improve DMA stability on sh-mobile
mmc: fix mmc_app_send_scr() for dma transfer
mmc: sdhci-esdhc: enable esdhc on imx53
mmc: sdhci-esdhc: use writel/readl as general APIs
mmc: sdhci: add the abort CMDTYPE bits definition
...
To get rid of port expanders, the free GPIOs of ab8500
can be used. There are 42 GPIO pins. Out of which 16
are interrupt capable.This patch implements 16 virtual
IRQ mapped to 16 interrupt capable AB8500 GPIOs.
Signed-off-by: Bibek Basu <bibek.basu@stericsson.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[Renamed header file as per MFD structure]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: Add MODULE_DEVICE_TABLE to max8997 and max8998
regulator: fix tps6524x section mismatch
regulator: Remove more wm831x-specific IRQ operations
regulator: add ab8500 enable and raise time delays
regulator: provide consumer interface for fall/rise time
regulator: add set_voltage_time_sel infrastructure
regulator: initialization for ab8500 regulators
regulator: add support for USB voltage regulator
regulator: switch the ab3100 to use enable_time()
Regulator: add suspend-finish API for regulator core.
regulator: fix typo in Kconfig
regulator: Convert WM831x regulators to genirq
regulator: If we fail when setting up a supply say which supply
This patch enables IRQ handling for MAX8997/8966 chips.
Please note that Fuel-Gauge-related IRQs are not implemented in this
initial release. The fuel gauge module in MAX8997 is identical to
MAX17042, which is already in Linux kernel. In order to use the
already-existing MAX17042 driver for fuel gauge module in MAX8997, the
main interrupt handler of MAX8997 should relay related interrupts to
MAX17042 driver. However, in order to do this, we need to modify
MAX17042 driver as well because MAX17042 driver does not have any
interrupt handlers for now. We are not going to implement this in this
initial release as it is not crucial in basic operations of MAX8997.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Replace mfd_shared_platform_driver_register with mfd_clone_cell. The
former was called by an mfd client, and registered both a platform driver
and device. The latter is called by an mfd driver, and registers only a
platform device.
The downside of this is that mfd drivers need to be modified whenever
new clients are added that share a cell; the upside is that it fits
Linux's driver model better. It's also simpler.
This also converts cs5535-mfd/olpc-xo1 from the old API. cs5535-mfd
now creates the olpc-xo1-{acpi,pms} devices, while olpc-xo1 binds to
them via platform drivers.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The regulators on the AB8500 have a lot of custom
hardware control settings pertaining to 8 external
signals, settings which are board-specific and need
be provided from the platform at startup.
Initialization added for regulators Vana, VextSupply1,
VextSupply2, VextSupply3, Vaux1, Vaux2, Vaux3, VTVout,
Vintcore12, Vaudio, Vdmic, Vamic1, Vamic2, VrefDDR.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
On sh-mobile platforms the SDHI driver was using the tmio_mmc SD/SDIO
MFD cell driver. Now that the tmio_mmc driver has been split into a
core and a separate MFD glue, we can support SDHI natively without the
need to emulate an MFD controller. This also allows to support systems
with an on-SoC SDHI controller and a separate MFD with a TMIO core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (442 commits)
[media] videobuf2-dma-contig: make cookie() return a pointer to dma_addr_t
[media] sh_mobile_ceu_camera: Do not call vb2's mem_ops directly
[media] V4L: soc-camera: explicitly require V4L2_BUF_TYPE_VIDEO_CAPTURE
[media] v4l: soc-camera: Store negotiated buffer settings
[media] rc: interim support for 32-bit NEC-ish scancodes
[media] mceusb: topseed 0x0011 needs gen3 init for tx to work
[media] lirc_zilog: error out if buffer read bytes != chunk size
[media] lirc: silence some compile warnings
[media] hdpvr: use same polling interval as other OS
[media] ir-kbd-i2c: pass device code w/key in hauppauge case
[media] rc/keymaps: Remove the obsolete rc-rc5-tv keymap
[media] remove the old RC_MAP_HAUPPAUGE_NEW RC map
[media] rc/keymaps: Rename Hauppauge table as rc-hauppauge
[media] rc-rc5-hauppauge-new: Fix Hauppauge Grey mapping
[media] rc-rc5-hauppauge-new: Add support for the old Black RC
[media] rc-rc5-hauppauge-new: Add the old control to the table
[media] rc-winfast: Fix the keycode tables
[media] a800: Fix a few wrong IR key assignments
[media] opera1: Use multimedia keys instead of an app-specific mapping
[media] dw2102: Use multimedia keys instead of an app-specific mapping
...
Fix up trivial conflicts (remove/modify and some real conflicts) in:
arch/arm/mach-omap2/devices.c
drivers/staging/Kconfig
drivers/staging/Makefile
drivers/staging/dabusb/dabusb.c
drivers/staging/dabusb/dabusb.h
drivers/staging/easycap/easycap_ioctl.c
drivers/staging/usbvideo/usbvideo.c
drivers/staging/usbvideo/vicam.c
Rename AB8500 GPADC header so as not to be redunantly named.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow const buffers to be passed in without type safety issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a subdriver for the regulator found inside the TPS61050
and TPS61052 chips.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TPS61050/TPS61052 are boost converters, LED drivers, LED flash
drivers and a simple GPIO pin chips.
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch supports PMIC/Regulator part of MAX8997/MAX8966 MFD.
In this initial release, selecting voltages or current-limit
and switching on/off the regulators are supported.
Controlling voltages for DVS with GPIOs is not implemented fully
and requires more considerations: it controls multiple bucks (selection
of 1, 2, and 5) at the same time with SET1~3 gpios. Thus, when DVS-GPIO
is activated, we lose the ability to control the voltage of a single
buck regulator independently; i.e., contolling a buck affects other two
bucks. Therefore, using the conventional regulator framework directly
might be problematic. However, in this driver, we try to choose
a setting without such side effect of affecting other regulators and
then try to choose a setting with the minimum side effect (the sum of
voltage changes in other regulators).
On the other hand, controlling all the three bucks simultenously based
on the voltage set table may help build cpufreq and similar system
more robust; i.e., all the three voltages are consistent every time
without glitches during transition.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Append the additional read/write operation on 88pm860x for accessing
test page in 88PM860x.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Copy 88pm860x platform data into different mfd_data structure for
regulator driver. So move the identification of device node from
regulator driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Copy 88pm860x platform data into different mfd_data structure for
led driver. So move the identification of device node from led
driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Copy 88pm860x platform data into different mfd_data structure for
backlight driver. So move the identification of device node from
backlight driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This revamps the interface so that AB8500 GPADCs are fetched by
name. Probed GPADCs are added to a list and this list is searched
for a matching GPADC. This makes it possible to have multiple
AB8500 GPADC instances instead of it being a singleton, and
rids the need to keep a GPADC pointer around in the core AB8500
MFD struct.
Currently the match is made to the device name which is by default
numbered from the device instance such as "ab8500-gpadc.0" but
by using the .init_name field of the device a more intiutive
naming for the GPADC blocks can be achieved if desired.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This moves the ab8500-gpadc.h header down into the ab8500/
subdir in include/linux/mfd and fixes some whitespace in the
header in the process.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MAX8997/MAX8966 chip is a multi-function device with I2C bussses. The
chip includes PMIC, RTC, Fuel Gauge, MUIC, Haptic, Flash control, and
Battery (charging) control.
This patch is an initial release of a MAX8997/8966 driver that supports
to enable the chip with its primary I2C bus that connects every device
mentioned above except for Fuel Gauge, which uses another I2C bus. The
fuel gauge is not supported by this mfd driver and is supported by a
seperated driver of MAX17042 Fuel Gauge (yes, the fuel gauge part is
compatible with MAX17042).
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As requested by Samuel, there's not really any reason to have "shared"
in the name.
This also modifies the only user of the function, as well.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds support for ab8500 chip revision cut 3.0.
Also rephrased from Changes to Author in the header.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If a system contains multiple WM831x devices we need to pass a device
number through to the MFD so that we use unique device IDs when we
instantiate child devices. In order to get support for this into 2.6.39
add some platform data to support the configuration, but no implementation
as yet.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds functions to enable platform_device sharing for mfd clients.
Each platform driver (mfd client) that wants to share an mfd_cell's
platform_device uses the mfd_shared_platform_driver_{un,}register()
functions instead of platform_driver_{un,}register(). Along with
registering the platform driver, these also register a new platform
device with the same characteristics as the original cell, but a different
name. Given an mfd_cell with the name "foo", drivers that want to
share access to its resources can call mfd_shared_platform_driver_register
with platform drivers named (for example) "bar" and "baz". This
will register two platform devices and drivers named "bar" and "baz"
that share the same cell as the platform device "foo". The drivers
can then call "foo" cell's enable hooks (or mfd_shared_cell_enable)
to enable resources, and obtain platform resources as they normally
would.
This deals with platform handling only; mfd driver-specific details,
hardware handling, refcounting, etc are all dealt with separately.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This provides convenience functions for sharing of cells across
multiple mfd clients. Mfd drivers can provide enable/disable hooks
to actually tweak the hardware, and clients can call
mfd_shared_cell_{en,dis}able without having to worry about whether
or not another client happens to have enabled or disabled the
cell/hardware.
Note that this is purely optional; drivers can continue to use
the mfd_cell's enable/disable hooks for their own purposes, if
desired.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
All users of this have now been switched over to using mfd_data;
it can go away now.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rename the platform_data variable to imply a distinction between
common platform_data driver usage (typically accessed via
pdev->dev.platform_data) and the way MFD passes data down to
clients (using a wrapper named mfd_get_data).
All clients have already been changed to use the wrapper function,
so this can be a quick single-commit change that only touches things
in drivers/mfd.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now that there are no more users of this, drop it.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that mfd-core no longer makes a copy of platform_data, but the
mc13xxx-core driver creates the pdata structures on the stack. In
order to get around that, the various ARM mach types that set the
pdata have been changed to hold the variable in static (global) memory.
Also note that __initdata references in aforementioned pdata structs
have been dropped.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No clients (in mainline kernel, I'm told that drivers exist in external
trees that are planned for mainline inclusion) make use of this, nor
do they make use of platform_data, so nothing really had to change here.
The .data_size field is unused, so its usage gets removed.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Previously, one would set the mfd_cell's platform_data/data_size to point
to the current mfd_cell in order to pass that information along to drivers.
This causes the current mfd_cell to always be available to drivers. It
also adds a wrapper function for fetching the mfd cell from a platform
device, similar to what originally existed for mfd devices.
Drivers who previously used platform_data for other purposes can still
use it; the difference is that mfd_get_data() must be used to
access it (and the pdata structure is no longer allocated in
mfd_add_devices).
Note that mfd_get_data is intentionally vague (in name) about where
the data is stored; variable name changes can come later without having
to touch brazillions of drivers.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a pretty straight-forward system control driver for the
AB8500. This driver will be used from the core platform, e.g the
clock tree implementation in the machine code, and is by nature
singleton.
There are a few simple functions to read, write, set and clear
registers so that the machine code can control its own foundation.
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Provide platform data allowing the system to set the /IRQ pin into
CMOS mode rather than the default open drain. The default value of
this platform data reflects the default hardware configuration so
there should be no change to existing users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
DSP2 in the WM8958 can be used to support an upgraded EQ for use in
demanding applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
With appropriate firmware the WM8958 can support Virtual Surround Sound or
VSS, widening the stereo audio image for improved user experience. Enable
support for this mode of operation when the appropriate firmware can be
loaded at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This is the core of the WL1273 FM radio driver, it connects
the two child modules. The two child drivers are
drivers/media/radio/radio-wl1273.c and sound/soc/codecs/wl1273.c.
The radio-wl1273 driver implements the V4L2 interface and communicates
with the device. The ALSA codec offers digital audio, without it only
analog audio is available.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tsc2005 - remove 'disable' sysfs attribute
Input: tsc2005 - add open/close
Input: tsc2005 - handle read errors from SPI layer
Input: tsc2005 - do not rearm timer in hardirq handler
Input: tsc2005 - don't use work for 'pen up' handling
Input: tsc2005 - do not use 0 in place of NULL
Input: tsc2005 - use true/false for boolean variables
Input: tsc2005 - hide selftest attribute if we can't reset
Input: tsc2005 - rework driver initialization code
Input: tsc2005 - set up bus type in input device
Input: tsc2005 - set up parent device
Input: tsc2005 - clear driver data after unbinding
Input: tsc2005 - add module description
Input: tsc2005 - remove driver banner message
Input: tsc2005 - remove incorrect module alias
Input: tsc2005 - convert to using dev_pm_ops
Input: tsc2005 - use spi_get/set_drvdata()
Input: introduce tsc2005 driver
Input: xen-kbdfront - move to drivers/input/misc
Input: xen-kbdfront - add grant reference for shared page
...
This patch adds an SPI master implementation that operates on top of an
underlying TI-SSP port.
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
TI's sequencer serial port (TI-SSP) is a jack-of-all-trades type of serial port
device. It has a built-in programmable execution engine that can be programmed
to operate as almost any serial bus (I2C, SPI, EasyScale, and others).
This patch adds a driver for this controller device. The driver does not
expose a user-land interface. Protocol drivers built on top of this layer are
expected to remain in-kernel.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
ASoC supports keeping the audio subsysetm active over suspend in order
to support use cases such as audio passthrough from a cellular modem
with the main CPU suspended. Ensure that we don't power down the CODEC
when this is happening by checking to see if VMID is up and skipping
suspend and resume when it is. If the CODEC has suspended then it'll
turn VMID off before the core suspend() gets called.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM8958 has a different microphone bias architecture to WM8994 so needs
different configuration to WM8994. Support this in platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow direct routing of the WM8958 microphone detection signal to a GPIO
to be used, saving the need to demux the interrupt.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some of the WM831x series of PMICs from Wolfson Microelectronics include
a resistive touchscreen controller. Implement support for these controllers
within the input API.
Platform data is supported to allow configuration of system parameters such
as selection between four and five wire touchscreens and for specification
of optional direct to CPU IRQs for sample availability and for pen down.
Use of this feature for at least the data IRQ is strongly recommended.
Thanks to Julien Boibessot for extensive testing and detailed feedback.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Julien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for chip version 2.0 or cut 2.0.
One new interrupt latch register - latch 12 - is introduced.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The previous driver did not support BUCK1-DVS3, BUCK1-DVS4, and
BUCK2-DVS2 modes. This patch adds such modes and an option to block
setting buck1/2 voltages out of the preset values.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The first releases of LP3974 have a large delay in RTC registers,
which requires 2 seconds of delay after writing to a rtc register
(recommended by National Semiconductor's engineers)
before reading it.
If "rtc_delay" field of the platform data is true, the rtc driver
assumes that such delays are required. Although we have not seen
LP3974s without requiring such delays, we assume that such LP3974s
will be released soon (or they have done so already) and they are
supported by "lp3974" without setting "rtc_delay" at the platform
data.
This patch adds delays with msleep when writing values to RTC registers
if the platform data has rtc_delay set.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch makes the driver to save and restore register values
for hibernation.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds the ioresources used by subdrivers to
retrieve their interrupt.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow MFD cells to have pm_runtime_no_callbacks() called on them during
registration. This causes the runtime PM framework to ignore them,
allowing use of runtime PM to suspend the device as a whole even if
not all drivers for the MFD can usefully implement runtime PM. For
example, RTCs are likely to run continuously regardless of the power
state of the system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM8326 is a high performance variant of the WM832x series with
no software visible differences.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: (45 commits)
regulator: missing index in PTR_ERR() in isl6271a_probe()
regulator: Assign return value of mc13xxx_reg_rmw to ret
regulator: Add initial per-regulator debugfs support
regulator: Make regulator_has_full_constraints a bool
regulator: Clean up logging a bit
regulator: Optimise out noop voltage changes
regulator: Add API to re-apply voltage to hardware
regulator: Staticise non-exported functions in mc13892
regulator: Only notify voltage changes when they succeed
regulator: Provide a selector based set_voltage_sel() operation
regulator: Factor out voltage set operation into a separate function
regulator: Convert WM8994 to use get_voltage_sel()
regulator: Convert WM835x to use get_voltage_sel()
regulator: Allow modular build of mc13xxx-core
regulator: support PMIC mc13892
make mc13783 regulator code generic
Change the register name definitions for mc13783
mach-ux500: Updated and connected ab8500 regulator board configuration
regulators: Removed macros for initialization of ab8500 regulators
regulators: Added verbose debug messages to ab8500 regulators
...
To make mc13783 and mc13892 share code, the register names should be
changed to fit the new macro definitions in the comming patch.
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The define for number of regulators is moved from ab8500-core to
ab8500-regulator so that the regulator driver can be updated
independently of ab8500-core. This also changes the platform
configuration structure of ab8500-core so that it contains a
pointer to the regulator_init_data array plus number of
regulators instead of an fixed size array of pointers to
regulator_init_data.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch implements SDIO IRQ support for mfds which
announce the TMIO_MMC_SDIO_IRQ flag for tmio_mmc.
If MMC_CAP_SDIO_IRQ is also set SDIO IRQ signalling is activated.
Tested with a b43-based wireless SDIO card and sh_mobile_sdhi.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
For example, with SDIO WLAN cards, some transfers happen with buffers at
odd addresses, whereas the SH-Mobile DMA engine requires even addresses
for SDHI. This patch extends the tmio driver with a bounce buffer, that
is used for single entry scatter-gather lists both for sending and
receiving. If we ever encounter unaligned transfers with multi-element
sg lists, this patch will have to be extended. For now it just falls
back to PIO in this and other unsupported cases.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add support for the keypad controller module found on the
TC3589X devices. This driver default adds the support for
TC35893 device.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
[Some minor fixups for compilation]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
This is the core of the WL1273 FM radio driver, it connects
the two child modules. The two child drivers are
drivers/media/radio/radio-wl1273.c and sound/soc/codecs/wl1273.c.
The radio-wl1273 driver implements the V4L2 interface and communicates
with the device. The ALSA codec offers digital audio, without it only
analog audio is available.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Add block identifier to be able to add multiple mfd clients
to the mfd core
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Most of the register layout, client IRQ numbers on the TC35892 is shared also
by other variants. Make this generic as tc3589x
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Rename the header file to include further variants within
the same mfd core driver
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Uk Kim <w0806.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Update some of the default configuration for the device to improve
the performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The paramters of the WM8958 multiband compressor can be tuned by the
user for their system using a graphical configuration tool on the host.
Allow the user to specify a set of such paramters in platform data and
select between them at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8958 contains an advanced accessory detection feature which allows
detection of up to seven different impedence levels on the microphone
bias output, including detection of video outputs. Since some of the
more involved accessory interfaces may involve noticable interactions
with external components a simple detection scheme is provided by
default with the option to provide custom handling of accessory detect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8958 features a multi-band compressor which can be enabled on
any of the AIF inputs. The MBC allows different gains to be applied to
differnt audio bands, providing an improvement in perceived loudness
of the signal by avoiding overdriving the output transducers. This
patch enables support for the MBC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Additional audio routing options are available on the WM8958 audio
interface 3. Add support for these.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8958 is a derivative of the WM8994 which is register compatible
with the addition of some extra features, mostly in the CODEC side.
The major change visible at the MFD level is that rather than a single
DBVDD supply we now have three separate DBVDDs so we must request and
enable a different set of supplies.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 driver was using some custom constants to interpret the direction
of the MCLK signal which had the opposite values to those used as standard
by the ASoC core, causing confusion in machine drivers such as the 1133-EV1
board.
Reported-by: Tommy Zhu <Tommy.Zhu@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In preparation for the addition of SPI support for the WM831x move the I2C
specific code into a separate file with a separate Kconfig option so the
I2C support can be excluded from the build.
Also update the 1133-EV1 PMIC module support for SMDK6410 to use the new
symbol.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
BUCK1/2 internal voltages and indexes defined in the struct max8998_data
max_get_voltage_register now uses index values to chose proper register
More generic BUCK1/2 registers names provided
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
mc13892 is the companion PMIC for Freescale's i.MX51. It's similar enough
to mc13782 to support it in a single driver.
This patch introduces enough compatibility cruft to keep all users of the
superseded mc13783 driver unchanged.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The last user is gone since v2.6.34-rc1~40
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming VIA VX855 MFD driver needs to communicate resources
to subdevices where the resources may be claimed by ACPI.
Add a flag to mfd_cell to request that resources are not policed.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Otherwise sparse warns about a public symbol with no declaration and
the compiler can't spot if the callers and users have different signatures
for the function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for enabling and disabling tps6586x subdevice interrupts
Signed-off-by: Gary King <gking@nvidia.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch makes the ab8500 mixed signal chip expose the same
interface for register access as the ab3100, ab3550 and ab5500 chip.
The ab8500_read() and ab8500_write() is removed and replaced with
abx500_get_register_interruptible() and
abx500_set_register_interruptible().
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adjust the tmio_mmc block size check to accept 2-byte requests in 4-bit
mode if the hardware supports it.
Tested with the SDHI hardware block included in sh7724.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Magnus Damm <damm@opensource.se>
Tested-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On some platforms (e.g. AP4EVB) the card detect pin of a slot is not
directly connected to the sdhi hardware, so that polling needs to be used
with tmio_mmc and card detection is handled in the platform code.
This patch allows to set tmio_mmc capabilities (to pass the
MMC_CAP_NEEDS_POLL flag) and exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some controllers, supported by the tmio_mmc driver do not have the card
detect pin of a slot connected, so that polling needs to be used and
card detection is handled by other means.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for the RTC provided by the Maxim 8998 chip. This
driver was tested on a GONI board by using the rtc-test application from
the Documentation/rtc.txt.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use genirq and provide seperated file for interrupts support.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The MAX8998 chip have regulator and rtc features. The i2c slave address
of regulator and rtc is different, so needs each i2c client on i2c
operation functions.
Also, this patch exports i2c operation functions instead of callback to
make easy to read.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
GPIOs on these controller are multi-functional. If you decided to use
some of them e.g. as input channels for the ADC, you surely don't want
those pins to be reassigned as simple GPIOs (which may be triggered even
from userspace via 'export'). Same for the touchscreen controller pins.
Since knowledge about the hardware is needed to decide which GPIOs to
reserve, let this bitmask be inside platform_data and provide some
defines to assist potential users.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixed warnings about unprototyped global functions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For board-specific initialization.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add mfd core driver for TPS6586x PMICs family.
The driver provides I/O access for the sub-device drivers and performs
regstration of the sub-devices based on the platform requirements.
In addition it implements GPIOlib interface for the chip GPIOs.
TODO:
- add interrupt support
- add platform data for PWM, backlight leds and charger
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Mike Rapoport <mike.rapoport@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds all remaining definitions that are used by the core driver
to the .c file.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is needed for the mc13783-adc driver to decide if a touch screen is
connected. If so some channels are not available as generic hwmon inputs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some STMPE devices support entering sleep mode automatically on a
specified timeout of inactivity on the I2C bus with the host system.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Later revisions of the WM8994 add some more GPIO functions, define them
in the header file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the STMPE family of I/O Expanders from
STMicroelectronics. These devices include upto 24 gpios and a varying
selection of blocks, including PWM, keypad, and touchscreen controllers.
This patch adds the MFD core.
[l.fu@pengutronix.de: fix stmpe811 enable hook]
[l.fu@pengutronix.de: add touchscreen platform data]
Acked-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds voltage regulator driver for Maxim 8998 chip. This chip
is used on Samsung Aquila and GONI boards and provides following
functionalities:
- 4 BUCK voltage converters, 17 LDO power regulators and 5 other power
controllers
- battery charger
This patch adds basic driver for voltage regulators and MAX 8998 MFD core.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add a new driver to support the AB8500 Power Management chip, replacing
the current AB4500. The new driver replaces the old one, instead of an
incremental modification, because this is a substantial overhaul
including:
- Split of the driver into -core and -spi portions, to allow another
interface layer to be added
- Addition of interrupt support
- Switch to MFD core API for handling subdevices
- Simplification of the APIs to remove a redundant block parameter
- Rename of the APIs and macros from ab4500_* to ab8500_*
- Rename of the files from ab4500* to ab8500*
- Change of the driver name from ab4500 to ab8500
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The interface for the AB3100 is changed to make way for the
ABX500 family of chips: AB3550, AB5500 and future ST-Ericsson
Analog Baseband chips. The register access functions are moved
out to a separate struct abx500_ops. In this way the interface
is moved from the implementation and the sub functionality drivers
can keep their interface intact when chip infrastructure and
communication mechanisms changes. We also define the AB3550
device IDs and the AB3550 platform data struct and convert
the catenated 32bit event to an array of 3 x 8bits.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The goal here is to make way for a more general interface for the
analog baseband chips ab3100 ab3550 ab550 and future chips.
This patch have been divided into two parts since both changing name
and content of a file is not recommended in git.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TC35892 I/O Expander provides 24 GPIOs, a keypad controller, timers,
and a rotator wheel interface. This patch adds the MFD core.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The charger interrupts on the WM831x are unconditionally a wake source
for the system. If the power driver is not able to monitor them (for
example, due to the IRQ line not having been wired up on the system)
then any charger interrupt will prevent the system suspending for any
meaningful amount of time since nothing will ack them.
Avoid this issue by manually acknowledging these interrupts when we
suspend the WM831x core device if they are masked. If software is
actually using the interrupts then they will be unmasked and this
change will have no effect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add touch screen input driver for TPS6507x family of multi-function
chips. Uses the TPS6507x MFD driver. No interrupt support due to
testing limitations of current hardware.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TPS6507x are multi function (PM, touchscreen) chipsets from TI.
This commit also changes the corresponding regulator driver from being
standalone to an MFD subdevice.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add mfd structure which refrences sub-driver initialization data. For example,
for a giving hardware implementation, the voltage regulator sub-driver
initialization data provides the mapping betten a voltage regulator and what
the output voltage is being used for.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Other sub-drivers for the TPS6507x chip will need to use register
definition so move it out of the source file and into a header file.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Janz CMOD-IO PCI MODULbus carrier board is a PCI to MODULbus bridge,
which may host many different types of MODULbus daughterboards, including
CAN and GPIO controllers.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fixes three section mismatches.
WARNING: drivers/mfd/88pm860x.o(.text+0x12): Section mismatch in
reference from the function pm860x_device_exit() to the function
.devexit.text:device_irq_exit()
The function pm860x_device_exit() references a function in an exit
section.
Often the function device_irq_exit() has valid usage outside the exit
section
and the fix is to remove the __devexit annotation of device_irq_exit.
WARNING: drivers/mfd/88pm860x.o(.text+0xb0): Section mismatch in
reference from the function pm860x_device_init() to the function
.devinit.text:device_8606_init()
The function pm860x_device_init() references
the function __devinit device_8606_init().
This is often because pm860x_device_init lacks a __devinit
annotation or the annotation of device_8606_init is wrong.
WARNING: drivers/mfd/88pm860x.o(.text+0xbe): Section mismatch in
reference from the function pm860x_device_init() to the function
.devinit.text:device_8607_init()
The function pm860x_device_init() references
the function __devinit device_8607_init().
This is often because pm860x_device_init lacks a __devinit
annotation or the annotation of device_8607_init is wrong.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a new MFD driver for the RDC321x southbridge. This southbridge
is always present in the RDC321x System-on-a-Chip and provides access to some
GPIOs as well as a watchdog. Access to these two functions is done using the
southbridge PCI device configuration space.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Register a device newly added pcf50633-backlight driver as a child device in
the pcf50633 core driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This patch adds a backlight driver for controlling the pcf50633 LED module.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This add basic led support for Freescale MC13783 PMIC.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
A lot of condition comparision statements are used in original driver. These
statements are used to check the boundary of voltage numbers since voltage
number isn't linear.
Now use array of voltage numbers instead. Clean code with simpler way.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Boards can have different supplied voltages on different SD card slots. This
information has to be passed down to the SD/MMC driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Write-protection status is not always available, e.g., micro-SD cards do not
have a write-protection switch at all. This patch adds a flag to let platforms
force tmio_mmc to consider the card writable.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pass DMA slave IDs from platform down to the tmio_mmc driver, to be used
for dmaengine configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
After this patch, if the "dma" pointer in struct tmio_mmc_data is not NULL, it
points to a struct, containing two tokens, that have to be passed to the
dmaengine driver for channel configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The WM8994 has an interrupt controller which supports interrupts for
both CODEC and GPIO portions of the chip. Support this using genirq,
while allowing for systems that do not have an interrupt hooked up.
Wrapper functions are provided for the IRQ request and free to simplify
the code in consumer drivers when handling cases where IRQs are not
set up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
The WM8350 provides microphone presence and short circuit detection.
Integrate this with the ASoC jack reporting API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is the MFD driver for the DaVinci Voice codec, it has two clients:
* Voice codec interface
* Voice codec CQ93VC
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes a build failure[1], by adding the missing semaphore.h include
References:
[1] http://kisskb.ellerman.id.au/kisskb/buildresult/2234322/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the status of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM831x interrupt infrastructure hooked
up.
Also reduce the timeout for completion of conversions to 5ms from
the previous 10ms, the lower timeout should be sufficient.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the state of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM8350 interrupt infrastructure hooked
up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Revision B of the WM831x devices changes the sense of the tristate
bit for GPIO configuration, inverting it to become an enable instead.
Take account of this in the gpiolib driver.
A current sink regulation status bit has also been added in revision B,
add a flag indicating if it's present but don't use it yet.
This revision also adds an interrupt on key up for the ON pin event
which the existing code is able to take advantage of.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove const from the tmio-mmc platform data hclk V3.
This change makes it possible to remove the type cast
from the sh_mobile_sdhi driver which is using the clock
framework to get the clock rate.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enable MMC_CAP_XX support in the tmio_mmc driver if
pdata->capabilities is set.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
