In general it is desirable that cleanup is the reverse process of setup.
In this case I am not seeing any particular issue, but with the
introduction of devlink-sb for felix, a non-obvious decision had to be
made as to where to put its cleanup method. When there's a convention in
place, that decision becomes obvious.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The devlink function pointer names are super long, and they would break
the alignment. So reindent the existing ops now by adding one tab.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Switches that care about QoS might have hardware support for reserving
buffer pools for individual ports or traffic classes, and configuring
their sizes and thresholds. Through devlink-sb (shared buffers), this is
all configurable, as well as their occupancy being viewable.
Add the plumbing in DSA for these operations.
Individual drivers still need to call devlink_sb_register() with the
shared buffers they want to expose. A helper was not created in DSA for
this purpose (unlike, say, dsa_devlink_params_register), since in my
opinion it does not bring any benefit over plainly calling
devlink_sb_register() directly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We'll need to read back the watermark thresholds and occupancy from
hardware (for devlink-sb integration), not only to write them as we did
so far in ocelot_port_set_maxlen. So introduce 2 new functions in struct
ocelot_ops, similar to wm_enc, and implement them for the 3 supported
mscc_ocelot switches.
Remove the INUSE and MAXUSE unpacking helpers for the QSYS_RES_STAT
register, because that doesn't scale with the number of switches that
mscc_ocelot supports now. They have different bit widths for the
watermarks, and we need function pointers to abstract that difference
away.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of reading these values from the reference manual and writing
them down into the driver, it appears that the hardware gives us the
option of detecting them dynamically.
The number of frame references corresponds to what the reference manual
notes, however it seems that the frame buffers are reported as slightly
less than the books would indicate. On VSC9959 (Felix), the books say it
should have 128KB of packet buffer, but the registers indicate only
129840 bytes (126.79 KB). Also, the unit of measurement for FREECNT from
the documentation of all these devices is incorrect (taken from an older
generation). This was confirmed by Younes Leroul from Microchip support.
Not having anything better to do with these values at the moment* (this
will change soon), let's just print them.
*The frame buffer size is, in fact, used to calculate the tail dropping
watermarks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sizeof needs to be called on the compat pointer, not the native one.
Fixes: 89cd35c58b ("iov_iter: transparently handle compat iovecs in import_iovec")
Reported-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
- Select missing Kconfig dependencies for DM integrity and zoned
targets.
- 4 fixes for DM crypt target's support to optionally bypass
kcryptd workqueues.
- Fix DM snapshot merge supports missing data flushes before
committing metadata.
- Fix DM integrity data device flushing when external metadata is
used.
- Fix DM integrity's maximum number of supported constructor arguments
that user can request when creating an integrity device.
- Eliminate DM core ioctl logging noise when an ioctl is issued
without required CAP_SYS_RAWIO permission.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEJfWUX4UqZ4x1O2wixSPxCi2dA1oFAmACJwsTHHNuaXR6ZXJA
cmVkaGF0LmNvbQAKCRDFI/EKLZ0DWr93B/sFpKbCjRxZhGdOz8u2UIV9jGoSzAaZ
3qdSTruCp1HMTsz0J/+bFBTMQKKap+8u8kzhCOLAqtZgEz13P0D3NyDUGiCxj07O
vPZJQ3COrClknq5byKws/aOKcnbr25odk6Zq+gFmk47pdNFBMkzNMf0IbdVJsj19
d0tnTRkIiycC8hnXOr/tHufnmERrw9nZpq3cLEHT6vaXc4FxcYXbo4UEMIwKjgcB
AnsRrqpqKyayG+G/SEs01JM9eYznWRPqf3L03wTWfieAsFjDoIp/ek8iXWjEwLtZ
BnhxFwodWvycFb9ITaxlFgfyiBSgU1f3tsIYjU4MHCSFI6u5b83y57Dl
=FnV7
-----END PGP SIGNATURE-----
Merge tag 'for-5.11/dm-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix DM-raid's raid1 discard limits so discards work.
- Select missing Kconfig dependencies for DM integrity and zoned
targets.
- Four fixes for DM crypt target's support to optionally bypass kcryptd
workqueues.
- Fix DM snapshot merge supports missing data flushes before committing
metadata.
- Fix DM integrity data device flushing when external metadata is used.
- Fix DM integrity's maximum number of supported constructor arguments
that user can request when creating an integrity device.
- Eliminate DM core ioctl logging noise when an ioctl is issued without
required CAP_SYS_RAWIO permission.
* tag 'for-5.11/dm-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm crypt: defer decryption to a tasklet if interrupts disabled
dm integrity: fix the maximum number of arguments
dm crypt: do not call bio_endio() from the dm-crypt tasklet
dm integrity: fix flush with external metadata device
dm: eliminate potential source of excessive kernel log noise
dm snapshot: flush merged data before committing metadata
dm crypt: use GFP_ATOMIC when allocating crypto requests from softirq
dm crypt: do not wait for backlogged crypto request completion in softirq
dm zoned: select CONFIG_CRC32
dm integrity: select CRYPTO_SKCIPHER
dm raid: fix discard limits for raid1
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-01-16
1) Extend atomic operations to the BPF instruction set along with x86-64 JIT support,
that is, atomic{,64}_{xchg,cmpxchg,fetch_{add,and,or,xor}}, from Brendan Jackman.
2) Add support for using kernel module global variables (__ksym externs in BPF
programs) retrieved via module's BTF, from Andrii Nakryiko.
3) Generalize BPF stackmap's buildid retrieval and add support to have buildid
stored in mmap2 event for perf, from Jiri Olsa.
4) Various fixes for cross-building BPF sefltests out-of-tree which then will
unblock wider automated testing on ARM hardware, from Jean-Philippe Brucker.
5) Allow to retrieve SOL_SOCKET opts from sock_addr progs, from Daniel Borkmann.
6) Clean up driver's XDP buffer init and split into two helpers to init per-
descriptor and non-changing fields during processing, from Lorenzo Bianconi.
7) Minor misc improvements to libbpf & bpftool, from Ian Rogers.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (41 commits)
perf: Add build id data in mmap2 event
bpf: Add size arg to build_id_parse function
bpf: Move stack_map_get_build_id into lib
bpf: Document new atomic instructions
bpf: Add tests for new BPF atomic operations
bpf: Add bitwise atomic instructions
bpf: Pull out a macro for interpreting atomic ALU operations
bpf: Add instructions for atomic_[cmp]xchg
bpf: Add BPF_FETCH field / create atomic_fetch_add instruction
bpf: Move BPF_STX reserved field check into BPF_STX verifier code
bpf: Rename BPF_XADD and prepare to encode other atomics in .imm
bpf: x86: Factor out a lookup table for some ALU opcodes
bpf: x86: Factor out emission of REX byte
bpf: x86: Factor out emission of ModR/M for *(reg + off)
tools/bpftool: Add -Wall when building BPF programs
bpf, libbpf: Avoid unused function warning on bpf_tail_call_static
selftests/bpf: Install btf_dump test cases
selftests/bpf: Fix installation of urandom_read
selftests/bpf: Move generated test files to $(TEST_GEN_FILES)
selftests/bpf: Fix out-of-tree build
...
====================
Link: https://lore.kernel.org/r/20210116012922.17823-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Defining DEBUG should only be done in development.
So remove DEBUG.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210115153128.131026-1-trix@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 54a0ed0df4 ("net: dsa: provide an option for
drivers to always receive bridge VLANs"), DSA has historically been
skipping VLAN switchdev operations when the bridge wasn't in
vlan_filtering mode, but the reason why it was doing that has never been
clear. So the configure_vlan_while_not_filtering option is there merely
to preserve functionality for existing drivers. It isn't some behavior
that drivers should opt into. Ideally, when all drivers leave this flag
set, we can delete the dsa_port_skip_vlan_configuration() function.
New drivers always seem to omit setting this flag, for some reason. So
let's reverse the logic: the DSA core sets it by default to true before
the .setup() callback, and legacy drivers can turn it off. This way, new
drivers get the new behavior by default, unless they explicitly set the
flag to false, which is more obvious during review.
Remove the assignment from drivers which were setting it to true, and
add the assignment to false for the drivers that didn't previously have
it. This way, it should be easier to see how many we have left.
The following drivers: lan9303, mv88e6060 were skipped from setting this
flag to false, because they didn't have any VLAN offload ops in the
first place.
The Broadcom Starfighter 2 driver calls the common b53_switch_alloc and
therefore also inherits the configure_vlan_while_not_filtering=true
behavior.
Also, print a message through netlink extack every time a VLAN has been
skipped. This is mildly annoying on purpose, so that (a) it is at least
clear that VLANs are being skipped - the legacy behavior in itself is
confusing, and the extack should be much more difficult to miss, unlike
kernel logs - and (b) people have one more incentive to convert to the
new behavior.
No behavior change except for the added prints is intended at this time.
$ ip link add br0 type bridge vlan_filtering 0
$ ip link set sw0p2 master br0
[ 60.315148] br0: port 1(sw0p2) entered blocking state
[ 60.320350] br0: port 1(sw0p2) entered disabled state
[ 60.327839] device sw0p2 entered promiscuous mode
[ 60.334905] br0: port 1(sw0p2) entered blocking state
[ 60.340142] br0: port 1(sw0p2) entered forwarding state
Warning: dsa_core: skipping configuration of VLAN. # This was the pvid
$ bridge vlan add dev sw0p2 vid 100
Warning: dsa_core: skipping configuration of VLAN.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210115231919.43834-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2021-01-16
1) Fix a double bpf_prog_put() for BPF_PROG_{TYPE_EXT,TYPE_TRACING} types in
link creation's error path causing a refcount underflow, from Jiri Olsa.
2) Fix BTF validation errors for the case where kernel modules don't declare
any new types and end up with an empty BTF, from Andrii Nakryiko.
3) Fix BPF local storage helpers to first check their {task,inode} owners for
being NULL before access, from KP Singh.
4) Fix a memory leak in BPF setsockopt handling for the case where optlen is
zero and thus temporary optval buffer should be freed, from Stanislav Fomichev.
5) Fix a syzbot memory allocation splat in BPF_PROG_TEST_RUN infra for
raw_tracepoint caused by too big ctx_size_in, from Song Liu.
6) Fix LLVM code generation issues with verifier where PTR_TO_MEM{,_OR_NULL}
registers were spilled to stack but not recognized, from Gilad Reti.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
MAINTAINERS: Update my email address
selftests/bpf: Add verifier test for PTR_TO_MEM spill
bpf: Support PTR_TO_MEM{,_OR_NULL} register spilling
bpf: Reject too big ctx_size_in for raw_tp test run
libbpf: Allow loading empty BTFs
bpf: Allow empty module BTFs
bpf: Don't leak memory in bpf getsockopt when optlen == 0
bpf: Update local storage test to check handling of null ptrs
bpf: Fix typo in bpf_inode_storage.c
bpf: Local storage helpers should check nullness of owner ptr passed
bpf: Prevent double bpf_prog_put call from bpf_tracing_prog_attach
====================
Link: https://lore.kernel.org/r/20210116002025.15706-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tobias Waldekranz says:
====================
net: dsa: mv88e6xxx: LAG fixes
The kernel test robot kindly pointed out that Global 2 support in
mv88e6xxx is optional.
This also made me realize that we should verify that the hardware
actually supports LAG offloading before trying to configure it.
====================
Link: https://lore.kernel.org/r/20210115125259.22542-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are chips that do have Global 2 registers, and therefore trunk
mapping/mask tables are not available. Refuse the offload as early as
possible on those devices.
Fixes: 57e661aae6 ("net: dsa: mv88e6xxx: Link aggregation support")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support for Global 2 registers is build-time optional. In the case
where it was not enabled the build would fail as no "dummy"
implementation of these functions was available.
Fixes: 57e661aae6 ("net: dsa: mv88e6xxx: Link aggregation support")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fl_set_enc_opt() simply checks if there are still bytes left to parse,
but this is not sufficent as syzbot seems to be able to generate
malformatted netlink messages. nla_ok() is more strict so should be
used to validate the next nlattr here.
And nla_validate_nested_deprecated() has less strict check too, it is
probably too late to switch to the strict version, but we can just
call nla_ok() too after it.
Reported-and-tested-by: syzbot+2624e3778b18fc497c92@syzkaller.appspotmail.com
Fixes: 0a6e77784f ("net/sched: allow flower to match tunnel options")
Fixes: 79b1011cb3 ("net: sched: allow flower to match erspan options")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Link: https://lore.kernel.org/r/20210115185024.72298-1-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
George McCollister says:
====================
Arrow SpeedChips XRS700x DSA Driver
This series adds a DSA driver for the Arrow SpeedChips XRS 7000 series
of HSR/PRP gigabit switch chips.
The chips use Flexibilis IP.
More information can be found here:
https://www.flexibilis.com/products/speedchips-xrs7000/
The switches have up to three RGMII ports and one MII port and are
managed via mdio or i2c. They use a one byte trailing tag to identify
the switch port when in managed mode so I've added a tag driver which
implements this.
This series contains minimal DSA functionality which may be built upon
in future patches. The ultimate goal is to add HSR and PRP
(IEC 62439-3 Clause 5 & 4) offloading with integration into net/hsr.
====================
Link: https://lore.kernel.org/r/20210114195734.55313-1-george.mccollister@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add documentation and an example for Arrow SpeedChips XRS7000 Series
single chip Ethernet switches.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a driver with initial support for the Arrow SpeedChips XRS7000
series of gigabit Ethernet switch chips which are typically used in
critical networking applications.
The switches have up to three RGMII ports and one RMII port.
Management to the switches can be performed over i2c or mdio.
Support for advanced features such as PTP and
HSR/PRP (IEC 62439-3 Clause 5 & 4) is not included in this patch and
may be added at a later date.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for Arrow SpeedChips XRS700x single byte tag trailer. This
is modeled on tag_trailer.c which works in a similar way.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge misc fixes from Andrew Morton:
"10 patches.
Subsystems affected by this patch series: MAINTAINERS and mm (slub,
pagealloc, memcg, kasan, vmalloc, migration, hugetlb, memory-failure,
and process_vm_access)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/process_vm_access.c: include compat.h
mm,hwpoison: fix printing of page flags
MAINTAINERS: add Vlastimil as slab allocators maintainer
mm/hugetlb: fix potential missing huge page size info
mm: migrate: initialize err in do_migrate_pages
mm/vmalloc.c: fix potential memory leak
arm/kasan: fix the array size of kasan_early_shadow_pte[]
mm/memcontrol: fix warning in mem_cgroup_page_lruvec()
mm/page_alloc: add a missing mm_page_alloc_zone_locked() tracepoint
mm, slub: consider rest of partial list if acquire_slab() fails
Several bug fixes.
- Fix a ucma memory leak introduced in v5.9 while fixing the Syzkaller
bugs
- Don't fail when the xarray wraps for user verbs objects
- User triggerable oops regression from the umem page size rework
- Error unwind bugs in usnic, ocrdma, mlx5 and cma
-----BEGIN PGP SIGNATURE-----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=8eDD
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"A fairly modest set of bug fixes, nothing abnormal from the merge
window
The ucma patch is a bit on the larger side, but given the regression
was recently added I've opted to forward it to the rc stream.
- Fix a ucma memory leak introduced in v5.9 while fixing the
Syzkaller bugs
- Don't fail when the xarray wraps for user verbs objects
- User triggerable oops regression from the umem page size rework
- Error unwind bugs in usnic, ocrdma, mlx5 and cma"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/cma: Fix error flow in default_roce_mode_store
RDMA/mlx5: Fix wrong free of blue flame register on error
IB/mlx5: Fix error unwinding when set_has_smi_cap fails
RDMA/umem: Avoid undefined behavior of rounddown_pow_of_two()
RDMA/ocrdma: Fix use after free in ocrdma_dealloc_ucontext_pd()
RDMA/usnic: Fix memleak in find_free_vf_and_create_qp_grp
RDMA/restrack: Don't treat as an error allocation ID wrapping
RDMA/ucma: Do not miss ctx destruction steps in some cases
Russell King says:
====================
Add further DT configuration for AT803x PHYs
This patch series adds the ability to configure the SmartEEE feature
in AT803x PHYs. SmartEEE defaults to enabled on these PHYs, and has
a history of causing random sporadic link drops at Gigabit speeds.
There appears to be two solutions to this. There is the approach that
Freescale adopted early on, which is to disable the SmartEEE feature.
However, this loses the power saving provided by EEE. Another solution
was found by Jon Nettleton is to increase the Tw parameter for Gigabit
links.
This patch series adds support for both approaches, by adding a boolean:
qca,disable-smarteee
if one wishes to disable SmartEEE, and two properties to configure the
SmartEEE Tw parameters:
qca,smarteee-tw-us-100m
qca,smarteee-tw-us-1g
Sadly, the PHY quirk I merged a while back for AT8035 on iMX6 is broken
- rather than disabling SmartEEE mode, it enables it.
The addition of these properties will be sent to the appropriate
platform maintainers - although for SolidRun platforms, we only make use
of "qca,smarteee-tw-us-1g".
====================
Link: https://lore.kernel.org/r/20210114104455.GP1551@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SmartEEE for the atheros phy was deemed buggy by Freescale and commits
were added to disable it for their boards.
In initial testing, SolidRun found that the default settings were
causing disconnects but by increasing the Tw buffer time we could allow
enough time for all parts of the link to come out of a low power state
and function properly without causing a disconnect. This allows us to
have functional power savings of between 300 and 400mW, rather than
disabling the feature altogether.
This commit adds support for disabling SmartEEE and configuring the Tw
parameters for 1G and 100M speeds.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SmartEEE feature of Atheros AR803x PHYs can cause the link to
bounce. Add DT properties to allow SmartEEE to be disabled, and to
allow the Tw parameters for 100M and 1G links to be configured.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we enter with requests pending and performm cancelations, we'll have
a different inflight count before and after calling prepare_to_wait().
This causes the loop to restart. If we actually ended up canceling
everything, or everything completed in-between, then we'll break out
of the loop without calling finish_wait() on the waitqueue. This can
trigger a warning on exit_signals(), as we leave the task state in
TASK_UNINTERRUPTIBLE.
Put a finish_wait() after the loop to catch that case.
Cc: stable@vger.kernel.org # 5.9+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
My Intel email will stop working in a not too distant future. Move my
MAINTAINERS entries to my kernel.org address.
Signed-off-by: Björn Töpel <bjorn@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210115104337.7751-1-bjorn.topel@gmail.com
* For the new fast_commit feature
* Fix some error handling codepaths in whiteout handling and
mountpoint sampling
* Fix how we write ext4_error information so it goes through the journal
when journalling is active, to avoid races that can lead to lost
error information, superblock checksum failures, or DIF/DIX features.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAmAB8eMACgkQ8vlZVpUN
gaMUxAf+MW22dceTto2RO0ox9OEBNoZDFiVnlEuUaIOxkqOlovIWaqX7wwuF/121
+FaNeDVzqNSS/QjQSB5lHF5OfHCD2u1Ef/bGzCm9cQyeN2/n0sCsStfPCcyLHy/0
4R8PsjF0xhhbCETLcAc0U/YBFEoqSn1i7DG5nnpx63Wt1S/SSMmTAXzafWbzisEZ
XNsz3CEPCDDSmSzOt3qMMHxkSoOZhYcLe7fCoKkhZ2pvTyrQsHrne6NNLtxc+sDL
AcKkaI0EWFiFRhebowQO/5ouq6nnGKLCsukuZN9//Br8ht5gNcFpuKNVFl+LOiM6
ud4H3qcRokcdPPAn3uwI0AJKFXqLvg==
=Dgdj
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A number of bug fixes for ext4:
- Fix for the new fast_commit feature
- Fix some error handling codepaths in whiteout handling and
mountpoint sampling
- Fix how we write ext4_error information so it goes through the
journal when journalling is active, to avoid races that can lead to
lost error information, superblock checksum failures, or DIF/DIX
features"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: remove expensive flush on fast commit
ext4: fix bug for rename with RENAME_WHITEOUT
ext4: fix wrong list_splice in ext4_fc_cleanup
ext4: use IS_ERR instead of IS_ERR_OR_NULL and set inode null when IS_ERR
ext4: don't leak old mountpoint samples
ext4: drop ext4_handle_dirty_super()
ext4: fix superblock checksum failure when setting password salt
ext4: use sbi instead of EXT4_SB(sb) in ext4_update_super()
ext4: save error info to sb through journal if available
ext4: protect superblock modifications with a buffer lock
ext4: drop sync argument of ext4_commit_super()
ext4: combine ext4_handle_error() and save_error_info()
-----BEGIN PGP SIGNATURE-----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=7ueC
-----END PGP SIGNATURE-----
Merge tag '5.11-rc3-smb3' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Two small cifs fixes for stable (including an important handle leak
fix) and three small cleanup patches"
* tag '5.11-rc3-smb3' of git://git.samba.org/sfrench/cifs-2.6:
cifs: style: replace one-element array with flexible-array
cifs: connect: style: Simplify bool comparison
fs: cifs: remove unneeded variable in smb3_fs_context_dup
cifs: fix interrupted close commands
cifs: check pointer before freeing
- Set the minimum GCC version to 5.1 for arm64 due to earlier compiler
bugs.
- Make atomic helpers __always_inline to avoid a section mismatch when
compiling with clang.
- Fix the CMA and crashkernel reservations to use ZONE_DMA (remove the
arm64_dma32_phys_limit variable, no longer needed with a dynamic
ZONE_DMA sizing in 5.11).
- Remove redundant IRQ flag tracing that was leaving lockdep
inconsistent with the hardware state.
- Revert perf events based hard lockup detector that was causing
smp_processor_id() to be called in preemptible context.
- Some trivial cleanups - spelling fix, renaming S_FRAME_SIZE to
PT_REGS_SIZE, function prototypes added.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE5RElWfyWxS+3PLO2a9axLQDIXvEFAmAB2zoACgkQa9axLQDI
XvE2vA//Vjh7bKMlNtocP7oA0/FVA7i9tKgNxDYmxjYvl6qDg26V7aDMelIi9H6l
14k+Wbf2Eqkav3+aAGEwdXuaoYPGrZIfVkPf+BbuviluoGsjwaGak0pc29ofDjE4
zaznZNXwO+joEqrtEZeTQO8fSagAupbgqf3ls/pRjBGVL6XEajhPqA+ccgQB71DI
O+L0Z1tzQDurABp4mwHGFRbOTMdN59OhxfyHijO3yu+RGLQcO3C29AwuMkzJuYuA
Fjng+VNS4mrKT8bsP0fpJa/oNekJ4jc/2OQaLxN+re8J+o6/EG6QGKdUL4VlEllk
eK0chdC/ZD1e6R9MSV0ZL1diYedi0vn+F9mGxwNiSKtWzw0KqPEy7liP0KWQGVyF
NALShoGkKMglYj2fmOrZhs7E4vAQGPlk7hROssDTM1RSu/7JpBwEJRb9QsOM4p4T
HgcCoF4smnTCmbyVkcMYgZxMrJ5YOjchTu8uvUwHy6D//ZMQmDE2m3u9Svziu+y3
Nk8VpIp0HNDZyA7ZTeOrmo2jSEOoK3tDVKiqorPSmZd5mp35BMCr1q/Rcu6uaywr
4ym/CfmvQIqObzQOYbBze6QZs4DLqERP1p0WgEnWBE8W2rP4UcGaNdegbEsMkrfq
CiCGcNyfpiJNZSc8VF1/1OFY/yABcWem1pVM7F254zA5G2wZX1U=
=W9th
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Set the minimum GCC version to 5.1 for arm64 due to earlier compiler
bugs.
- Make atomic helpers __always_inline to avoid a section mismatch when
compiling with clang.
- Fix the CMA and crashkernel reservations to use ZONE_DMA (remove the
arm64_dma32_phys_limit variable, no longer needed with a dynamic
ZONE_DMA sizing in 5.11).
- Remove redundant IRQ flag tracing that was leaving lockdep
inconsistent with the hardware state.
- Revert perf events based hard lockup detector that was causing
smp_processor_id() to be called in preemptible context.
- Some trivial cleanups - spelling fix, renaming S_FRAME_SIZE to
PT_REGS_SIZE, function prototypes added.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: selftests: Fix spelling of 'Mismatch'
arm64: syscall: include prototype for EL0 SVC functions
compiler.h: Raise minimum version of GCC to 5.1 for arm64
arm64: make atomic helpers __always_inline
arm64: rename S_FRAME_SIZE to PT_REGS_SIZE
Revert "arm64: Enable perf events based hard lockup detector"
arm64: entry: remove redundant IRQ flag tracing
arm64: Remove arm64_dma32_phys_limit and its uses
When 'perf inject' reads a perf.data file from an older version of perf,
it writes event attributes into the output with the original size field,
but lays them out as if they had the size currently used. Readers see a
corrupt file. Update the size field to match the layout.
Signed-off-by: Al Grant <al.grant@foss.arm.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20201124195818.30603-1-al.grant@arm.com
Signed-off-by: Denis Nikitin <denik@chromium.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In some cases, the number of cpus (nr_cpus_online) is confused with the
maximum cpu number (nr_cpus_avail), which results in the error in the
example below:
Example on system with 8 cpus:
Before:
# echo 0 > /sys/devices/system/cpu/cpu2/online
# ./perf record --kcore -e intel_pt// taskset --cpu-list 7 uname
Linux
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.147 MB perf.data ]
# ./perf script --itrace=e
Requested CPU 7 too large. Consider raising MAX_NR_CPUS
0x25908 [0x8]: failed to process type: 68 [Invalid argument]
After:
# ./perf script --itrace=e
#
Fixes: 8c7274691f ("perf machine: Replace MAX_NR_CPUS with perf_env::nr_cpus_online")
Fixes: 7df4e36a47 ("perf session: Replace MAX_NR_CPUS with perf_env::nr_cpus_online")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/20210107174159.24897-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
As of now it doesn't consider cgroups when collecting shadow stats and
metrics so counter values from different cgroups will be saved in a same
slot. This resulted in incorrect numbers when those cgroups have
different workloads.
For example, let's look at the scenario below: cgroups A and C runs same
workload which burns a cpu while cgroup B runs a light workload.
$ perf stat -a -e cycles,instructions --for-each-cgroup A,B,C sleep 1
Performance counter stats for 'system wide':
3,958,116,522 cycles A
6,722,650,929 instructions A # 2.53 insn per cycle
1,132,741 cycles B
571,743 instructions B # 0.00 insn per cycle
4,007,799,935 cycles C
6,793,181,523 instructions C # 2.56 insn per cycle
1.001050869 seconds time elapsed
When I run 'perf stat' with single workload, it usually shows IPC around
1.7. We can verify it (6,722,650,929.0 / 3,958,116,522 = 1.698) for cgroup A.
But in this case, since cgroups are ignored, cycles are averaged so it
used the lower value for IPC calculation and resulted in around 2.5.
avg cycle: (3958116522 + 1132741 + 4007799935) / 3 = 2655683066
IPC (A) : 6722650929 / 2655683066 = 2.531
IPC (B) : 571743 / 2655683066 = 0.0002
IPC (C) : 6793181523 / 2655683066 = 2.557
We can simply compare cgroup pointers in the evsel and it'll be NULL
when cgroups are not specified. With this patch, I can see correct
numbers like below:
$ perf stat -a -e cycles,instructions --for-each-cgroup A,B,C sleep 1
Performance counter stats for 'system wide':
4,171,051,687 cycles A
7,219,793,922 instructions A # 1.73 insn per cycle
1,051,189 cycles B
583,102 instructions B # 0.55 insn per cycle
4,171,124,710 cycles C
7,192,944,580 instructions C # 1.72 insn per cycle
1.007909814 seconds time elapsed
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20210115071139.257042-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To pass more info to the saved_value in the runtime_stat, add a new
struct runtime_stat_data. Currently it only has 'ctx' field but later
patch will add more.
Note that we intentionally pass 0 as ctx to clock-related events for
compatibility. It was already there in a few places. So move the code
into the saved_value_lookup() explicitly and add a comment.
Suggested-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20210115071139.257042-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Permissions are necessary to get a tracepoint id. Fail the test when the
read fails.
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20210114180250.3853825-2-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
If a test fails return -1 rather than 0. This is consistent with the
return value in test-cpumap.c
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20210114180250.3853825-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The variable 'bf' is read (for a write call) without being initialized
triggering a memory sanitizer warning. Use 'bf' in the read and switch
the write to reading from a string.
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20210114212304.4018119-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In the fast commit, it adds REQ_FUA and REQ_PREFLUSH on each fast
commit block when barrier is enabled. However, in recovery phase,
ext4 compares CRC value in the tail. So it is sufficient to add
REQ_FUA and REQ_PREFLUSH on the block that has tail.
Signed-off-by: Daejun Park <daejun7.park@samsung.com>
Reviewed-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20210106013242epcms2p5b6b4ed8ca86f29456fdf56aa580e74b4@epcms2p5
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
We got a "deleted inode referenced" warning cross our fsstress test. The
bug can be reproduced easily with following steps:
cd /dev/shm
mkdir test/
fallocate -l 128M img
mkfs.ext4 -b 1024 img
mount img test/
dd if=/dev/zero of=test/foo bs=1M count=128
mkdir test/dir/ && cd test/dir/
for ((i=0;i<1000;i++)); do touch file$i; done # consume all block
cd ~ && renameat2(AT_FDCWD, /dev/shm/test/dir/file1, AT_FDCWD,
/dev/shm/test/dir/dst_file, RENAME_WHITEOUT) # ext4_add_entry in
ext4_rename will return ENOSPC!!
cd /dev/shm/ && umount test/ && mount img test/ && ls -li test/dir/file1
We will get the output:
"ls: cannot access 'test/dir/file1': Structure needs cleaning"
and the dmesg show:
"EXT4-fs error (device loop0): ext4_lookup:1626: inode #2049: comm ls:
deleted inode referenced: 139"
ext4_rename will create a special inode for whiteout and use this 'ino'
to replace the source file's dir entry 'ino'. Once error happens
latter(the error above was the ENOSPC return from ext4_add_entry in
ext4_rename since all space has been consumed), the cleanup do drop the
nlink for whiteout, but forget to restore 'ino' with source file. This
will trigger the bug describle as above.
Signed-off-by: yangerkun <yangerkun@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org
Fixes: cd808deced ("ext4: support RENAME_WHITEOUT")
Link: https://lore.kernel.org/r/20210105062857.3566-1-yangerkun@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
After full/fast commit, entries in staging queue are promoted to main
queue. In ext4_fs_cleanup function, it splice to staging queue to
staging queue.
Fixes: aa75f4d3da ("ext4: main fast-commit commit path")
Signed-off-by: Daejun Park <daejun7.park@samsung.com>
Reviewed-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201230094851epcms2p6eeead8cc984379b37b2efd21af90fd1a@epcms2p6
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
1: ext4_iget/ext4_find_extent never returns NULL, use IS_ERR
instead of IS_ERR_OR_NULL to fix this.
2: ext4_fc_replay_inode should set the inode to NULL when IS_ERR.
and go to call iput properly.
Fixes: 8016e29f43 ("ext4: fast commit recovery path")
Signed-off-by: Yi Li <yili@winhong.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20201230033827.3996064-1-yili@winhong.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
In rvu_mbox_handler_cgx_mac_addr_get()
and rvu_mbox_handler_cgx_mac_addr_set(),
the msg is expected only from PFs that are mapped to CGX LMACs.
It should be checked before mapping,
so we add the is_cgx_config_permitted() in the functions.
Fixes: 96be2e0da8 ("octeontx2-af: Support for MAC address filters in CGX")
Signed-off-by: Yingjie Wang <wangyingjie55@126.com>
Reviewed-by: Geetha sowjanya<gakula@marvell.com>
Link: https://lore.kernel.org/r/1610719804-35230-1-git-send-email-wangyingjie55@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It was using some bash-specific features and failed to parse when
running with a different shell like below:
root@kbl-ppc:~/kbl-ws/perf-dev/lck-9077/acme.tmp/tools/perf# ./perf test 83 -vv
83: perf stat metrics (shadow stat) test :
--- start ---
test child forked, pid 3922
./tests/shell/stat+shadow_stat.sh: 19: ./tests/shell/stat+shadow_stat.sh: [[: not found
./tests/shell/stat+shadow_stat.sh: 24: ./tests/shell/stat+shadow_stat.sh: [[: not found
./tests/shell/stat+shadow_stat.sh: 30: ./tests/shell/stat+shadow_stat.sh: [[: not found
(standard_in) 2: syntax error
./tests/shell/stat+shadow_stat.sh: 36: ./tests/shell/stat+shadow_stat.sh: [[: not found
./tests/shell/stat+shadow_stat.sh: 19: ./tests/shell/stat+shadow_stat.sh: [[: not found
./tests/shell/stat+shadow_stat.sh: 24: ./tests/shell/stat+shadow_stat.sh: [[: not found
./tests/shell/stat+shadow_stat.sh: 30: ./tests/shell/stat+shadow_stat.sh: [[: not found
(standard_in) 2: syntax error
./tests/shell/stat+shadow_stat.sh: 36: ./tests/shell/stat+shadow_stat.sh: [[: not found
./tests/shell/stat+shadow_stat.sh: 45: ./tests/shell/stat+shadow_stat.sh: declare: not found
test child finished with -1
---- end ----
perf stat metrics (shadow stat) test: FAILED!
Reported-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Laight <david.laight@aculab.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20210114050609.1258820-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To pick up the changes in:
3a176b9460 ("Revert "kbuild: avoid static_assert for genksyms"")
And silence this perf build warning:
Warning: Kernel ABI header at 'tools/include/linux/build_bug.h' differs from latest version at 'include/linux/build_bug.h'
diff -u tools/include/linux/build_bug.h include/linux/build_bug.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
