Change log from v1:
o fix 32bit drops reported by Dan Carpenter
This patch adds f2fs_issue_discard() to clean up blkdev_issue_discard() flows.
Dan carpenter reported:
"block_t is a 32 bit type and sector_t is a 64 bit type. The upper 32
bits of the sector_t are not used because the shift will wrap."
Bug-Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If frequent small discards are issued to the device, the performance would
be degraded significantly.
So, this patch adds a sysfs entry to control the number of discards to be
issued during a checkpoint procedure.
By default, f2fs does not issue any small discards, which means max_discards
is zero.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds key functions to activate the small discard feature.
Note that this procedure is conducted during the checkpoint only.
In flush_sit_entries(), when a new dirty sit entry is flushed, f2fs calls
add_discard_addrs() which searches candidates to be discarded.
The candidates should be marked *invalidated* and also previous checkpoint
recognizes it as *valid*.
At the end of a checkpoint procedure, f2fs throws discards based on the
discard entry list.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a slab cache entry for small discards.
Each entry consists of:
struct discard_entry {
struct list_head list; /* list head */
block_t blkaddr; /* block address to be discarded */
int len; /* # of consecutive blocks of the discard */
};
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
To find a zero bit using the result of OR operation between ckpt_valid_map
and cur_valid_map is more fast than find a zero bit in each bitmap.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
[Jaegeuk Kim: adjust changed function name]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When f2fs_set_bit is used, in a byte MSB and LSB is reversed,
in that case we can use __find_rev_next_bit or __find_rev_next_zero_bit.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
[Jaegeuk Kim: change the function names]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
With immutable biovecs we don't want code accessing bi_io_vec directly -
the uses this patch changes weren't incorrect since they all own the
bio, but it makes the code harder to audit for no good reason - also,
this will help with multipage bvecs later.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Cc: Joern Engel <joern@logfs.org>
Cc: Prasad Joshi <prasadjoshi.linux@gmail.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
o Changes from v1
Use find_next(_zero)_bit suggested by jg.kim
When f2fs issues discard command, if segment is contiguous,
let's issue more large segment to gather adjacent segments.
** blktrace **
179,1 0 5859 42.619023770 971 C D 131072 + 2097152 [0]
179,1 0 33665 108.840475468 971 C D 2228224 + 2494464 [0]
179,1 0 33671 109.131616427 971 C D 14909440 + 344064 [0]
179,1 0 33677 109.137100677 971 C D 15261696 + 4096 [0]
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If we failed to init&add kobject when fill_super, stats info and proc object of
f2fs will not be released.
We should free them before we finish fill_super.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
use genernal method supported by kernel
o changes from v1
If any waiter exists at end io, wake up it.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
A NULL point should avoid to be used in destroy_segment_manager after allocating
memory fail for f2fs_sm_info.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In wait_on_node_pages_writeback we will test and clear error flag for all
pages in radix tree, but not necessary.
So we only do this for pages belong to the specified inode.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, f2fs_sync_file() waits for all the node blocks to be written.
But, we don't need to do that, but wait only the inode-related node blocks.
This patch adds wait_on_node_pages_writeback() in which waits inode-related
node blocks that are on writeback.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, check_block_count check valid_map with bit data type in common
scenario that sit has all ones or zeros bitmap, it makes low mount performance.
So let's check the special bitmap with integer data type instead of the bit one.
v1-->v2:
o use find_next_{zero_}bit_le for better performance and readable as Jaegeuk
suggested.
o use neat logogram in comment as Gu Zheng suggested.
o search continuous ones or zeros for better performance when checking mixed
bitmap.
Suggested-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Signed-off-by: Shu Tan <shu.tan@samsung.com>
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
npages_for_summary_flush uses (SUMMARY_SIZE + 1) as the size of a f2fs_summary
while its actual size is SUMMARY_SIZE. So the result sometimes is bigger than
actual number by one, which causes checkpoint can't be written into disk
contiguously, and sometimes summary blocks can't be compacted like they should.
Besides, when writing summary blocks into pages, if remain space in a page
isn't big enough for one f2fs_summary, it will be left unused, current code
seems not to take it into account.
Signed-off-by: Fan Li <fanofcode.li@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
During xattr updating, free size should be corrected to remainder free size
+ old entry size.
It can avoid ENOSPC error when we update old entry with the same size new
entry at fully filled xattr.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If you want to remove unnecessary BUG_ONs, you can just turn off F2FS_CHECK_FS
in your kernel config.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This config will support an option to remove so many BUG_ONs that degrade
the performance potentially.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The deadlock is found through the following scenario.
sys_mkdir()
-> f2fs_add_link()
-> __f2fs_add_link()
-> init_inode_metadata()
: lock_page(inode);
-> f2fs_init_acl()
-> f2fs_set_acl()
-> f2fs_setxattr(..., NULL)
: This NULL page incurs a deadlock at update_inode_page().
So, likewise f2fs_init_security(), this patch adds a parameter to transfer the
locked inode page to f2fs_setxattr().
Found by Linux File System Verification project (linuxtesting.org).
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Only one dirty type is set in __locate_dirty_segment and we can know
dirty type of segment. So we don't need to check other dirty types.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, set_page_dirty is called every time after writting one summary info
into compacted summary page,
To avoid redundant set_page_dirty, we only call set_page_dirty before release
page.
Signed-off-by: Yu Chao <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a control method in sysfs to reclaim prefree segments.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch merges some background jobs into this new function.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, f2fs postpones reclaiming prefree segments into free segments
as much as possible.
However, if user writes and deletes a bunch of data without any sync or fsync
calls, some flash storages can suffer from garbage collections.
So, this patch adds the reclaiming codes to f2fs_write_node_pages and background
GC thread.
If there are a lot of prefree segments, let's do checkpoint so that f2fs
submits discard commands for the prefree regions to the flash storage.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Introduce the unfailed version of kmem_cache_alloc named f2fs_kmem_cache_alloc
to hide the retry routine and make the code a bit cleaner.
v2:
Fix the wrong use of 'retry' tag pointed out by Gao feng.
Use more neat code to remove redundant tag suggested by Haicheng Li.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Because one dirty seg can only be mapped to one dirty_type. Otherwise, it's a bug.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
[Jaegeuk Kim: modify a comment related to this patch]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch enhances the recovery routine not to write any data/node/meta until
its completion.
If any writes are sent to the disk, it could contaminate the written history
that will be used for further recovery.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, do_checkpoint() will call congestion_wait() for waiting the pages
(previous submitted node/meta/data pages) to be written back.
Because congestion_wait() will set a regular period (e.g. HZ / 50 ) for waiting, and
no additional wake up mechanism was introduced if IO ends up before regular period costed.
Yuan Zhong found there is a situation that after the pages have been written back,
but the checkpoint thread still wait for congestion_wait to exit.
So here we store checkpoint task into f2fs_sb when doing checkpoint, it'll wait for IO completes
if there's IO going on, and in the end IO path, wake up checkpoint task when IO ends up.
Thanks to Yuan Zhong's pre work about this problem.
Reported-by: Yuan Zhong <yuan.mark.zhong@samsung.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Introduce function read_raw_super_block() to hide reading raw super block and
the retry routine if the first sb is invalid.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch removes the logic previously introduced to address the starvation
on cp_rwsem.
One potential there-in bug is that we should cover the wait.list with spin_lock,
but the previous code broke this rule.
And, actually current rwsem handles this starvation issue reasonably, so that we
didn't need to do this before neither.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, there was a erroneous scenario like below.
thread 1: thread 2:
f2fs_unlink
- acquire_orphan_inode
: sbi->n_orphans++ write_checkpoint
- block_operations
: f2fs_lock_all
- do_checkpoint
: write orphan blocks with sbi->n_orphans
- unblock_operations
- f2fs_lock_op
- release_orphan_inode
- f2fs_unlock_op
During the checkpoint by thread 2, f2fs stores a wrong orphan block according
to the wrong sbi->n_orphans.
To avoid this, simply we should make cover acquire_orphan_inode too with
f2fs_lock_op.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
During the f2fs_put_super procedure, we don't need to conduct checkpoint all
the time, since we don't need to do that if superblock is clean.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The current f2fs code errors if the xattr or acl options are passed when
remounting. This is important in a typical scenario where f2fs is mounted
as a "ro" root file-system by the boot loader and then the init process wants
to remount it "rw" with the "remount,rw" option.
Signed-off-by: Kelly Anderson <kelly@xilka.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The fs_locks is used to block other ops(ex, recovery) when doing checkpoint.
And each other operate routine(besides checkpoint) needs to acquire a fs_lock,
there is a terrible problem here, if these are too many concurrency threads acquiring
fs_lock, so that they will block each other and may lead to some performance problem,
but this is not the phenomenon we want to see.
Though there are some optimization patches introduced to enhance the usage of fs_lock,
but the thorough solution is using a *rw_sem* to replace the fs_lock.
Checkpoint routine takes write_sem, and other ops take read_sem, so that we can block
other ops(ex, recovery) when doing checkpoint, and other ops will not disturb each other,
this can avoid the problem described above completely.
Because of the weakness of rw_sem, the above change may introduce a potential problem
that the checkpoint thread might get starved if other threads are intensively locking
the read semaphore for I/O.(Pointed out by Xu Jin)
In order to avoid this, a wait_list is introduced, the appending read semaphore ops
will be dropped into the wait_list if checkpoint thread is waiting for write semaphore,
and will be waked up when checkpoint thread gives up write semaphore.
Thanks to Kim's previous review and test, and will be very glad to see other guys'
performance tests about this patch.
V2:
-fix the potential starvation problem.
-use more suitable func name suggested by Xu Jin.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
[Jaegeuk Kim: adjust minor coding standard]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
During recovery, orphan inodes are deleted via truncate_hole().
These orphans are added by recover_dentry() via f2fs_delete_entry().
However, f2fs_delete_entry() adds them via add_orphan_inode()
without calling acquire_orphan_inode() first. This prevents the
counters from being incremented properly, which causes them to
underflow when remove_orphan_inode() is called later on.
Signed-off-by: Russ Knize <rknize@motorola.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
f2fs_initxattrs() is called internally from within F2FS and should
not call functions that are used by VFS handlers. This avoids
certain deadlocks:
- vfs_create()
- f2fs_create() <-- takes an fs_lock
- f2fs_add_link()
- __f2fs_add_link()
- init_inode_metadata()
- f2fs_init_security()
- security_inode_init_security()
- f2fs_initxattrs()
- f2fs_setxattr() <-- also takes an fs_lock
If the caller happens to grab the same fs_lock from the pool in both
places, they will deadlock. There are also deadlocks involving
multiple threads and mutexes:
- f2fs_write_begin()
- f2fs_balance_fs() <-- takes gc_mutex
- f2fs_gc()
- write_checkpoint()
- block_operations()
- mutex_lock_all() <-- blocks trying to grab all fs_locks
- f2fs_mkdir() <-- takes an fs_lock
- __f2fs_add_link()
- f2fs_init_security()
- security_inode_init_security()
- f2fs_initxattrs()
- f2fs_setxattr()
- f2fs_balance_fs() <-- blocks trying to take gc_mutex
Signed-off-by: Russ Knize <Russ.Knize@motorola.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Accounting errors from buggy code calling the acquire/release/remove
orphan inode interfaces can cause n_orphans to underflow, which will
then cause acquire_orphan_inode() to return -ENOSPC on the next
operation. This commit guards against that condition.
Signed-off-by: Russ Knize <rknize@motorola.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, recover_fsync_data still to write checkpoint when there is
nothing to recover with normal umount image.
It may reduce mount performance and flash memory lifetime, so let's remove
it.
Signed-off-by: Tan Shu <shu.tan@samsung.com>
Signed-off-by: Yu Chao <chao2.yu@samsung.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch add macro MAX_BIO_BLOCKS to limit value of npages in
f2fs_bio_alloc, it can avoid allocating failure in bio_alloc caused by
npages is larger than BIO_MAX_PAGES.
Signed-off-by: Yu Chao <chao2.yu@samsung.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Since the MAX_VICTIM_SEARCH has been enlarged from 20 to 4096,
the victim searching overhead will be increased much than before,
especially for SSR that searches victim for use quiet often.
This patch intends to reduce the overhead a little bit by:
- make the get_gc_cost a inline routine to reduce function call
overhead
- reduce multiplication and division operations
- reduce unnecessary comparison operation
Signed-off-by: Jin Xu <jinuxstyle@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
There is a performance problem: when all sbi->fs_lock are holded, then
all the following threads may get the same next_lock value from sbi->next_lock_num
in function mutex_lock_op, and wait for the same lock(fs_lock[next_lock]),
it may cause performance reduce.
So we move the sbi->next_lock_num++ before getting lock, this will average the
following threads if all sbi->fs_lock are holded.
v1-->v2:
Drop the needless spin_lock as Jaegeuk suggested.
Suggested-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Signed-off-by: Yu Chao <chao2.yu@samsung.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch improves the gc efficiency by optimizing the victim
selection policy. With this optimization, the random re-write
performance could increase up to 20%.
For f2fs, when disk is in shortage of free spaces, gc will selects
dirty segments and moves valid blocks around for making more space
available. The gc cost of a segment is determined by the valid blocks
in the segment. The less the valid blocks, the higher the efficiency.
The ideal victim segment is the one that has the most garbage blocks.
Currently, it searches up to 20 dirty segments for a victim segment.
The selected victim is not likely the best victim for gc when there
are much more dirty segments. Why not searching more dirty segments
for a better victim? The cost of searching dirty segments is
negligible in comparison to moving blocks.
In this patch, it enlarges the MAX_VICTIM_SEARCH to 4096 to make
the search more aggressively for a possible better victim. Since
it also applies to victim selection for SSR, it will likely improve
the SSR efficiency as well.
The test case is simple. It creates as many files until the disk full.
The size for each file is 32KB. Then it writes as many as 100000
records of 4KB size to random offsets of random files in sync mode.
The testing was done on a 2GB partition of a SDHC card. Let's see the
test result of f2fs without and with the patch.
---------------------------------------
2GB partition, SDHC
create 52023 files of size 32768 bytes
random re-write 100000 records of 4KB
---------------------------------------
| file creation (s) | rewrite time (s) | gc count | gc garbage blocks |
[no patch] 341 4227 1174 174840
[patched] 324 2958 645 106682
It's obvious that, with the patch, f2fs finishes the test in 20+% less
time than without the patch. And internally it does much less gc with
higher efficiency than before.
Since the performance improvement is related to gc, it might not be so
obvious for other tests that do not trigger gc as often as this one (
This is because f2fs selects dirty segments for SSR use most of the
time when free space is in shortage). The well-known iozone test tool
was not used for benchmarking the patch becuase it seems do not have
a test case that performs random re-write on a full disk.
This patch is the revised version based on the suggestion from
Jaegeuk Kim.
Signed-off-by: Jin Xu <jinuxstyle@gmail.com>
[Jaegeuk Kim: suggested simpler solution]
Reviewed-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, we experience bio traces as follows when running simple sequential
write test.
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 500104928, size = 4K
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 499922208, size = 368K
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 499914752, size = 140K
-> total 512K
The first one is to write an indirect node block, and the others are to write
direct node blocks.
The reason why there are two separate bios for direct node blocks is:
0. initial state
------------------ ------------------
| | |xxxxxxxx |
------------------ ------------------
1. write 368K
------------------ ------------------
| | |xxxxxxxxWWWWWWWW|
------------------ ------------------
2. write 140K
------------------ ------------------
|WWWWWWW | |xxxxxxxxWWWWWWWW|
------------------ ------------------
This is because f2fs_write_node_pages tries to write just 512K totally, so that
we can lose the chance to merge more bios nicely.
After this patch is applied, we can get the following bio traces.
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 500103168, size = 8K
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 500111368, size = 4K
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 500107272, size = 512K
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 500108296, size = 512K
f2fs_do_submit_bio: type = NODE, io = no sync, sector = 500109320, size = 500K
And finally, we can improve the sequential write performance,
from 458.775 MB/s to 479.945 MB/s on SSD.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The current f2fs uses all the block counts with 32 bit numbers, which is able to
cover about 15TB volume.
But in calculation of utilization, f2fs multiplies the count by 100 which can
induce overflow.
This patch fixes this.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, f2fs conducts SSR when free_sections() < overprovision_sections.
But, even though there are a lot of prefree segments, it can consider SSR only.
So, let's consider the number of prefree segments too for triggering SSR.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The f2fs_set_link updates its parent inode number, so we should sync this to
the inode block.
Otherwise, the data can be lost after sudden-power-off.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
0. modified inode structure
--------------------------------------
metadata (e.g., i_mtime, i_ctime, etc)
--------------------------------------
direct pointers [0 ~ 873]
inline xattrs (200 bytes by default)
indirect pointers [0 ~ 4]
--------------------------------------
node footer
--------------------------------------
1. setxattr flow
- read_all_xattrs copies all the xattrs from inline and xattr node block.
- handle xattr entries
- write_all_xattrs copies modified xattrs into inline and xattr node block.
2. getxattr flow
- read_all_xattrs copies all the xattrs from inline and xattr node block.
- check target entries
3. Usage
# mount -t f2fs -o inline_xattr $DEV $MNT
Once mounted with the inline_xattr option, f2fs marks all the newly created
files to reserve an amount of inline xattr space explicitly inside the inode
block. Without the mount option, f2fs will not touch any existing files and
newly created files as well.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The __find_xattr is to search the wanted xattr entry starting from the
base_addr.
If not found, the returned entry is the last empty xattr entry that can be
allocated newly.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch enables the number of direct pointers inside on-disk inode block to
be changed dynamically according to the size of inline xattr space.
The number of direct pointers, ADDRS_PER_INODE, can be changed only if the file
has inline xattr flag.
The number of direct pointers that will be used by inline xattrs is defined as
F2FS_INLINE_XATTR_ADDRS.
Current patch assigns F2FS_INLINE_XATTR_ADDRS to 0 temporarily.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds basic inode flags for inline xattrs, F2FS_INLINE_XATTR,
and add a mount option, inline_xattr, which is enabled when xattr is set.
If the mount option is enabled, all the files are marked with the inline_xattrs
flag.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Fix to return -ENOMEM in the kset create and add error handling
case instead of 0, as done elsewhere in this function.
Introduced by commit b59d0bae6c.
(f2fs: add sysfs support for controlling the gc_thread)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Namjae Jeon <namjae.jeon@samsung.com>
[Jaegeuk Kim: merge the patch with previous modification]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch removes a false-alaramed BUG_ON.
The previous BUG_ON condition didn't cover the following true scenario.
In f2fs_add_link, 1) get_new_data_page gives an uptodate page successfully,
and then, 2) init_inode_metadata returns -ENOSPC.
At this moment, a new clean data page is remained in the page cache, but its
block address still indicates NEW_ADDR.
After then, even if sync is called, this clean data page cannot be written to
the disk due to the clean state.
So this means that get_lock_data_page should make a new empty page when its
block address is NEW_ADDR and its page is not uptodated.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When any of the caches create fails in init_f2fs_fs(), the other caches which are
create successful should be free.
Signed-off-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
An error "label at end of compound statement" will occur if CONFIG_F2FS_STAT_FS
disabled.
fs/f2fs/segment.c:556:1: error: label at end of compound statement
So clean up the 'out' label to fix it.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In f2fs_write_inode, updating inode after f2fs_balance_fs is not
a optimized way in the case that f2fs_gc is performed ahead. The
inode page will be unnecessarily written out twice, one of which
is in f2fs_gc->...->sync_node_pages and the other is in
update_inode_page.
Let's update the inode page in prior to f2fs_balance_fs to avoid
this.
To reproduce it,
$ touch file (before this step, should make the device need f2fs_gc)
$ sync (or wait the bdi to write dirty inode)
Signed-off-by: Jin Xu <jinuxstyle@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
alloc_page() returns a NULL on failure, it never returns an ERR_PTR.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, f2fs_setxattr assigns i_xattr_nid in the inode page inconsistently.
The scenario is:
= Thread 1 = = Thread 2 = = fi->i_xattr_nid = = on-disk nid =
f2fs_setxattr 0 0
new_node_page X 0
sync_inode_page X X
checkpoint X X -.
grab_cache_page X X |
--> allocate a new xattr node block or -ENOSPC <----------------'
At this moment, the checkpoint stores inconsistent data where the inode has
i_xattr_nid but actual xattr node block is not allocated yet.
So, we should assign the real i_xattr_nid only after its xattr node block is
allocated.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously xattr node blocks are stored to the COLD_NODE log, which means that
our roll-forward mechanism doesn't recover the xattr node blocks at all.
Only the direct node blocks in the WARM_NODE log can be recovered.
So, let's resolve the issue simply by conducting checkpoint during fsync when a
file has a modified xattr node block.
This approach is able to degrade the performance, but normally the checkpoint
overhead is shown at the initial fsync call after the xattr entry changes.
Once the checkpoint is done, no additional overhead would be occurred.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch fixes the use of XATTR_NODE_OFFSET.
o The offset should not use several MSB bits which are used by marking node
blocks.
o IS_DNODE should handle XATTR_NODE_OFFSET to avoid potential abnormality
during the fsync call.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch should resolve the following error reported by kbuild test robot.
All error/warnings:
In file included from fs/f2fs/dir.c:13:0:
>> fs/f2fs/f2fs.h:435:17: error: field 's_kobj' has incomplete type
struct kobject s_kobj;
The failure was caused by missing the kobject header file in dir.c.
So, this patch move the header file to the right location, f2fs.h.
CC: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch fixes a deadlock bug that occurs quite often when there are
concurrent write and fsync on a same file.
Following is the simplified call trace when tasks get hung.
fsync thread:
- f2fs_sync_file
...
- f2fs_write_data_pages
...
- update_extent_cache
...
- update_inode
- wait_on_page_writeback
bdi writeback thread
- __writeback_single_inode
- f2fs_write_data_pages
- mutex_lock(sbi->writepages)
The deadlock happens when the fsync thread waits on a inode page that has
been added to the f2fs' cached bio sbi->bio[NODE], and unfortunately,
no one else could be able to submit the cached bio to block layer for
writeback. This is because the fsync thread already hold a sbi->fs_lock and
the sbi->writepages lock, causing the bdi thread being blocked when attempt
to write data pages for the same inode. At the same time, f2fs_gc thread
does not notice the situation and could not help. Even the sync syscall
gets blocked.
To fix it, we could submit the cached bio first before waiting on a inode page
that is being written back.
Signed-off-by: Jin Xu <jinuxstyle@gmail.com>
[Jaegeuk Kim: add more cases to use f2fs_wait_on_page_writeback]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This code is being used for nobh_write_end() function.
But since now f2fs_write_end function is added so
there is no need for this code.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add sysfs entry gc_idle to control the gc policy. Where
gc_idle = 1 corresponds to selecting a cost benefit approach,
while gc_idle = 2 corresponds to selecting a greedy approach
to garbage collection. The selection is mutually exclusive one
approach will work at any point. If gc_idle = 0, then this
option is disabled.
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
[Jaegeuk Kim: change the select_gc_type() flow slightly]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add sysfs entries to control the timing parameters for
f2fs gc thread.
Various Sysfs options introduced are:
gc_min_sleep_time: Min Sleep time for GC in ms
gc_max_sleep_time: Max Sleep time for GC in ms
gc_no_gc_sleep_time: Default Sleep time for GC in ms
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
[Jaegeuk Kim: fix an umount bug and some minor changes]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This kfree() is no longer needed after a79dc083d7 "f2fs: move
bio_private allocation out of f2fs_bio_alloc()". The "bio->bi_private"
is NULL here so it's a no-op.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch fixes mishandling of the sbi->n_orphans variable.
If users request lots of f2fs_unlink(), check_orphan_space() could be contended.
In such the case, sbi->n_orphans can be read incorrectly so that f2fs_unlink()
would fall into the wrong state which results in the failure of
add_orphan_inode().
So, let's increment sbi->n_orphans virtually prior to the actual orphan inode
stuffs. After that, let's release sbi->n_orphans by calling release_orphan_inode
or remove_orphan_inode.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
bio->bi_private is not always needed. As in the reading data path,
end_read_io does not need bio_private for further using, so moving
bio_private allocation out of f2fs_bio_alloc(). Alloc it in the
submit_write_page(), and ignore it in the f2fs_readpage().
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
As we remove the target single node, so list_for_each is enought, in order to
clean up, we use list_for_each_entry instead.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
For string without format specifiers, using seq_puts()/seq_putc()
instead of seq_printf().
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
As similar as the i_pino fix, i_name also should be fixed when i_nlink is 1.
The errorneous scenario is like this.
1. touch test1
2. link test1 test2
3. unlink test2
4. fsync test1
After this, i_name should be test1.
CC: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The error is reproducible by:
0. mkfs.f2fs /dev/sdb1 & mount
1. touch test1
2. touch test2
3. mv test1 test2
4. umount
5. dumpt.f2fs -i 4 /dev/sdb1
After this, when we retrieve the inode->i_name of test2 by dump.f2fs, we get
test1 instead of test2.
This is because f2fs didn't update the file name during the f2fs_rename.
So, this patch fixes that.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Introduce help function F2FS_NODE() to simplify the conversion of node_page to
f2fs_node.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add a help func F2FS_STAT() to get the f2fs_stat_info.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In order to support SQLite that uses fdatasync instead of fsync, we should
guarantee the data requested by fdatasync can be recovered after sudden-power-
off.
So, let's remove the fdatasync condition in f2fs_sync_file.
Otherwise, we can restore the data after sudden-power-off due to nonexistence
of any fsync mark'ed node blocks.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In the previous Al Viro's readdir patch set, there occurs a bug when
running
xfstest: 006 as follows.
[Error output]
alpha size = 4, name length = 6, total files = 4096, nproc=1
1023 files created
rm: cannot remove `/mnt/f2fs/permname.15150/a': Directory not empty
[Correct output]
alpha size = 4, name length = 6, total files = 4096, nproc=1
4097 files created
This bug is due to the misupdate of directory position in ctx.
So, this patch fixes this.
[AV: fixed a braino]
CC: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
o remount_fs callback function
o restore parent inode number to enhance the fsync performance
o xattr security labels
o reduce the number of redundant lock/unlock data pages
o avoid frequent write_inode calls
The other minor bug fixes are as follows.
o endian conversion bugs
o various bugs in the roll-forward recovery routine
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=qFcy
-----END PGP SIGNATURE-----
Merge tag 'for-f2fs-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"This patch-set includes the following major enhancement patches:
- remount_fs callback function
- restore parent inode number to enhance the fsync performance
- xattr security labels
- reduce the number of redundant lock/unlock data pages
- avoid frequent write_inode calls
The other minor bug fixes are as follows.
- endian conversion bugs
- various bugs in the roll-forward recovery routine"
* tag 'for-f2fs-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (56 commits)
f2fs: fix to recover i_size from roll-forward
f2fs: remove the unused argument "sbi" of func destroy_fsync_dnodes()
f2fs: remove reusing any prefree segments
f2fs: code cleanup and simplify in func {find/add}_gc_inode
f2fs: optimize the init_dirty_segmap function
f2fs: fix an endian conversion bug detected by sparse
f2fs: fix crc endian conversion
f2fs: add remount_fs callback support
f2fs: recover wrong pino after checkpoint during fsync
f2fs: optimize do_write_data_page()
f2fs: make locate_dirty_segment() as static
f2fs: remove unnecessary parameter "offset" from __add_sum_entry()
f2fs: avoid freqeunt write_inode calls
f2fs: optimise the truncate_data_blocks_range() range
f2fs: use the F2FS specific flags in f2fs_ioctl()
f2fs: sync dir->i_size with its block allocation
f2fs: fix i_blocks translation on various types of files
f2fs: set sb->s_fs_info before calling parse_options()
f2fs: support xattr security labels
f2fs: fix iget/iput of dir during recovery
...
category, of note is a fix for on-line resizing file systems where the
block size is smaller than the page size (i.e., file systems 1k blocks
on x86, or more interestingly file systems with 4k blocks on Power or
ia64 systems.)
In the cleanup category, the ext4's punch hole implementation was
significantly improved by Lukas Czerner, and now supports bigalloc
file systems. In addition, Jan Kara significantly cleaned up the
write submission code path. We also improved error checking and added
a few sanity checks.
In the optimizations category, two major optimizations deserve
mention. The first is that ext4_writepages() is now used for
nodelalloc and ext3 compatibility mode. This allows writes to be
submitted much more efficiently as a single bio request, instead of
being sent as individual 4k writes into the block layer (which then
relied on the elevator code to coalesce the requests in the block
queue). Secondly, the extent cache shrink mechanism, which was
introduce in 3.9, no longer has a scalability bottleneck caused by the
i_es_lru spinlock. Other optimizations include some changes to reduce
CPU usage and to avoid issuing empty commits unnecessarily.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=SwaI
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 update from Ted Ts'o:
"Lots of bug fixes, cleanups and optimizations. In the bug fixes
category, of note is a fix for on-line resizing file systems where the
block size is smaller than the page size (i.e., file systems 1k blocks
on x86, or more interestingly file systems with 4k blocks on Power or
ia64 systems.)
In the cleanup category, the ext4's punch hole implementation was
significantly improved by Lukas Czerner, and now supports bigalloc
file systems. In addition, Jan Kara significantly cleaned up the
write submission code path. We also improved error checking and added
a few sanity checks.
In the optimizations category, two major optimizations deserve
mention. The first is that ext4_writepages() is now used for
nodelalloc and ext3 compatibility mode. This allows writes to be
submitted much more efficiently as a single bio request, instead of
being sent as individual 4k writes into the block layer (which then
relied on the elevator code to coalesce the requests in the block
queue). Secondly, the extent cache shrink mechanism, which was
introduce in 3.9, no longer has a scalability bottleneck caused by the
i_es_lru spinlock. Other optimizations include some changes to reduce
CPU usage and to avoid issuing empty commits unnecessarily."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (86 commits)
ext4: optimize starting extent in ext4_ext_rm_leaf()
jbd2: invalidate handle if jbd2_journal_restart() fails
ext4: translate flag bits to strings in tracepoints
ext4: fix up error handling for mpage_map_and_submit_extent()
jbd2: fix theoretical race in jbd2__journal_restart
ext4: only zero partial blocks in ext4_zero_partial_blocks()
ext4: check error return from ext4_write_inline_data_end()
ext4: delete unnecessary C statements
ext3,ext4: don't mess with dir_file->f_pos in htree_dirblock_to_tree()
jbd2: move superblock checksum calculation to jbd2_write_superblock()
ext4: pass inode pointer instead of file pointer to punch hole
ext4: improve free space calculation for inline_data
ext4: reduce object size when !CONFIG_PRINTK
ext4: improve extent cache shrink mechanism to avoid to burn CPU time
ext4: implement error handling of ext4_mb_new_preallocation()
ext4: fix corruption when online resizing a fs with 1K block size
ext4: delete unused variables
ext4: return FIEMAP_EXTENT_UNKNOWN for delalloc extents
jbd2: remove debug dependency on debug_fs and update Kconfig help text
jbd2: use a single printk for jbd_debug()
...
If user requests many data writes and fsync together, the last updated i_size
should be stored to the inode block consistently.
But, previous write_end just marks the inode as dirty and doesn't update its
metadata into its inode block.
After that, fsync just writes the inode block with newly updated data index
excluding inode metadata updates.
So, this patch introduces write_end in which updates inode block too when the
i_size is changed.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
As destroy_fsync_dnodes() is a simple list-cleanup func, so delete the unused
and unrelated f2fs_sb_info argument of it.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch removes check_prefree_segments initially designed to enhance the
performance by narrowing the range of LBA usage across the whole block device.
When allocating a new segment, previous f2fs tries to find proper prefree
segments, and then, if finds a segment, it reuses the segment for further
data or node block allocation.
However, I found that this was totally wrong approach since the prefree segments
have several data or node blocks that will be used by the roll-forward mechanism
operated after sudden-power-off.
Let's assume the following scenario.
/* write 8MB with fsync */
for (i = 0; i < 2048; i++) {
offset = i * 4096;
write(fd, offset, 4KB);
fsync(fd);
}
In this case, naive segment allocation sequence will be like:
data segment: x, x+1, x+2, x+3
node segment: y, y+1, y+2, y+3.
But, if we can reuse prefree segments, the sequence can be like:
data segment: x, x+1, y, y+1
node segment: y, y+1, y+2, y+3.
Because, y, y+1, and y+2 became prefree segments one by one, and those are
reused by data allocation.
After conducting this workload, we should consider how to recover the latest
inode with its data.
If we reuse the prefree segments such as y or y+1, we lost the old node blocks
so that f2fs even cannot start roll-forward recovery.
Therefore, I suggest that we should remove reusing prefree segments.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch simplifies list operations in find_gc_inode and add_gc_inode.
Just simple code cleanup.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
[Jaegeuk Kim: add description]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Optimize the while loop condition
Since this condition will always be true and while loop will
be terminated by the following condition in code:
if (segno >= TOTAL_SEGS(sbi))
break;
Hence we can replace the while loop condition with while(1)
instead of always checking for segno to be less than Total segs.
Also we do not need to use TOTAL_SEGS() everytime. We can store
this value in a local variable since this value is constant.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch should fix the following bug reported by kbuild test robot.
fs/f2fs/recovery.c:233:33: sparse: incorrect type in assignment
(different base types)
parse warnings: (new ones prefixed by >>)
>> recovery.c:233: sparse: incorrect type in assignment (different base types)
recovery.c:233: expected unsigned int [unsigned] [assigned] ofs_in_node
recovery.c:233: got restricted __le16 [assigned] [usertype] ofs_in_node
>> recovery.c:238: sparse: incorrect type in assignment (different base types)
recovery.c:238: expected unsigned int [unsigned] ofs_in_node
recovery.c:238: got restricted __le16 [assigned] [usertype] ofs_in_node
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
While calculating CRC for the checkpoint block, we use __u32, but when storing
the crc value to the disk, we use __le32.
Let's fix the inconsistency.
Reported-and-Tested-by: Oded Gabbay <ogabbay@advaoptical.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add the f2fs_remount function call which will be used
during the filesystem remounting. This function
will help us to change the mount options specific to
f2fs.
Also modify the f2fs background_gc mount option, which
will allow the user to dynamically trun on/off the
garbage collection in f2fs based on the background_gc
value. If background_gc=on, Garbage collection will
be turned off & if background_gc=off, Garbage collection
will be truned on.
By default the garbage collection is on in f2fs.
Change Log:
v2: Incorporated the review comments by Gu Zheng.
Removing the restore part for VFS flags
Updating comments with proper flag conditions
Display GC background option as ON/OFF
Revised conditions to stop GC in case of remount
v1: Initial changes for adding remount_fs callback
support.
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
[Jaegeuk Kim: change /** with /* for the coding style]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If a file is linked, f2fs loose its parent inode number so that fsync calls
for the linked file should do checkpoint all the time.
But, if we can recover its parent inode number after the checkpoint, we can
adjust roll-forward mechanism for the further fsync calls, which is able to
improve the fsync performance significatly.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Since "need_inplace_update() == true" is a very rare case, using unlikely()
to give compiler a chance to optimize the code.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
It's used only locally and could be static.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We can get the value directly from pointer "curseg".
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If update_inode is called, we don't need to do write_inode.
So, let's use a *dirty* flag for each inode.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The function truncate_data_blocks_range() decrements the valid
block count of inode via dec_valid_block_count(). Since this
function updates the i_blocks field of inode, we can update this
field once we have calculated total the number of blocks
to be freed.
Therefore we can decrement valid blocks outside of the for loop.
if (nr_free) {
+ dec_valid_block_count(sbi, dn->inode, nr_free);
set_page_dirty(dn->node_page);
sync_inode_page(dn);
}
'nr_free' tells the total number of blocks freed. So, we can
just directly pass this value to dec_valid_block_count() and update
the i_blocks.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In f2fs_ioctl() function, it is using generic flags.
Since F2FS specific flags are defined. So lets use
those flags.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If new dentry block is allocated and its i_size is updated, we should update
its inode block together in order to sync i_size and its block allocation.
Otherwise, we can loose additional dentry block due to the unconsistent i_size.
Errorneous Scenario
-------------------
In the recovery routine,
- recovery_dentry
| - __f2fs_add_link
| | - get_new_data_page
| | | - i_size_write(new_i_size)
| | | - mark_inode_dirty_sync(dir)
| | - update_parent_metadata
| | | - mark_inode_dirty(dir)
|
- write_checkpoint
- sync_dirty_dir_inodes
- filemap_flush(dentry_blocks)
- f2fs_write_data_page
- skip to write the last dentry block due to index < i_size
In the above flow, new_i_size is not updated to its inode block so that the
last dentry block will be lost accordingly.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Basically an inode manages the number of allocated blocks with inode->i_blocks
which is represented in a unit of sectors, not file system blocks.
But, f2fs has used i_blocks in a unit of file system blocks, and f2fs_getattr
translates it to the number of sectors when fstat is called.
However, previously f2fs_file_inode_operations only has this, so this patch adds
it to all the types of inode_operations.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In f2fs_fill_super(), set sb->s_fs_info before calling parse_options(), then we can get
f2fs_sb_info via F2FS_SB(sb) in parse_options().
So that the second argument "sbi" of func parse_options() is no longer needed.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds the support of security labels for f2fs, which will be used
by Linus Security Models (LSMs).
Quote from http://en.wikipedia.org/wiki/Linux_Security_Modules:
"Linux Security Modules (LSM) is a framework that allows the Linux kernel to
support a variety of computer security models while avoiding favoritism toward
any single security implementation. The framework is licensed under the terms of
the GNU General Public License and is standard part of the Linux kernel since
Linux 2.6. AppArmor, SELinux, Smack and TOMOYO Linux are the currently accepted
modules in the official kernel.".
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
It is possible that iput is skipped after iget during the recovery.
In recover_dentry(),
dir = f2fs_iget();
...
if (de && inode->i_ino == le32_to_cpu(de->ino))
goto out;
In this case, this dir is not able to be added in dirty_dir_inode_list.
The actual linking is done only when set_page_dirty() is called.
So let's add this newly got inode into the list explicitly, and put it at the
end of the recovery routine.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Fix the function get_victim_by_default, where it checks
for the condition that p.min_segno != NULL_SEGNO as
shown:
if (p.min_segno != NULL_SEGNO)
goto got_it;
and if above condition is true then
got_it:
if (p.min_segno != NULL_SEGNO) {
So this condition is being checked twice. Hence move the goto
statement after the if condition so that duplication of condition
check is avoided.
Also this function makes a call to get_max_cost() to compute
the max cost based on the f2fs_sbi_info and victim policy. Since
get_max_cost depends on on three parameters of victim_sel_policy
=> alloc_mode, gc_mode & ofs_unit, once this victim policy is
initialised, these value will not change till the execution
time of get_victim_by_default() & also f2fs_sbi_info structure
parameters will not change.
Hence making calls to get_max_cost() in while loop does not seems to
be a good point. Instead we can call it once in begining and store
the results in local variable, which later can serve our purpose
for comparing the cost with max cost inside the while loop.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add check for error pointers returned from get_node_page in order to
avoid dereferencing a bad address on the next use.
Signed-off-by: Jason Hrycay <jason.hrycay@motorola.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If a file is linked with other files, it should be checkpointed at every fsync
calls.
For this, we use set_cp_file() with FADVISE_CP_BIT, but previously we didn't
cover the flag by the global lock.
This patch fixes that the inode page stores this correctly.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
- iget/iput flow in the dentry recovery process
1. *dir* = f2fs_iget
2. set FI_DELAY_IPUT to *dir*
3. add *dir* to the dirty_dir_list
- __f2fs_add_link
- recover_dentry)
4. iput *dir* by remove_dirty_dir_inode
- sync_dirty_dir_inodes
- write_chekcpoint
If *dir*'s i_count is not 1 (i.e., root dir), remove_dirty_dir_inode is called
later and then iput is triggered again due to the FI_DELAY_IPUT flag.
So, let's unset the flag properly once iput is triggered.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The error scenario is:
1. create /a
(1.a link /a /b)
2. sync
3. unlinke /a
4. create /a
5. fsync /a
6. Sudden power-off
When the f2fs recovers the fsynced dentry, /a, we discover an exsiting dentry at
f2fs_find_entry() in recover_dentry().
In such the case, we should unlink the existing dentry and its inode
and then recover newly created dentry.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If there remains some unwritten blocks from the recovery, we should not call
iput on that directory inode.
Otherwise, we can loose some dentry blocks after the recovery.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
when there is an error from kthread_run, then return proper error
rather than returning -ENOMEM.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
There are various functions with common code which could be separated
out to make common routines. So, made new routines and in order to
retain the same call path and no major changes, written some macros
to access those routines.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
There is no need to initialize few pointers in f2fs_parent_dir
as the values are not checked and instead directly initialized
values are used.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Some, counters are needed only for the statistical information
while debugging.
So, those can be controlled using CONFIG_F2FS_STAT_FS,
pushing the usage for few variables under this flag.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The on-disk block address is defined as __le32, but in-memory block address,
block_t, does as u64.
Let's synchronize them to 32 bits.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
There is an error path where "dir" is an ERR_PTR.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Use the following helper function committed by Al.
commit 7de9c6ee3e
Author: Al Viro <viro@zeniv.linux.org.uk>
Date: Sat Oct 23 11:11:40 2010 -0400
new helper: ihold()
...
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If -ENOSPC is met during f2fs_link, we should not make the inode as bad.
The inode is still alive.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds error handling codes of check_index_in_prev_nodes and its
caller, do_recover_data.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch fixes the following deadlock bug during the recovery.
INFO: task mount:1322 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
mount D ffffffff81125870 0 1322 1266 0x00000000
ffff8801207e39d8 0000000000000046 ffff88012ab1dee0 0000000000000046
ffff8801207e3a08 ffff880115903f40 ffff8801207e3fd8 ffff8801207e3fd8
ffff8801207e3fd8 ffff880115903f40 ffff8801207e39d8 ffff88012fc94520
Call Trace:
[<ffffffff81125870>] ? __lock_page+0x70/0x70
[<ffffffff816a92d9>] schedule+0x29/0x70
[<ffffffff816a93af>] io_schedule+0x8f/0xd0
[<ffffffff8112587e>] sleep_on_page+0xe/0x20
[<ffffffff816a649a>] __wait_on_bit_lock+0x5a/0xc0
[<ffffffff81125867>] __lock_page+0x67/0x70
[<ffffffff8106c7b0>] ? autoremove_wake_function+0x40/0x40
[<ffffffff81126857>] find_lock_page+0x67/0x80
[<ffffffff8112698f>] find_or_create_page+0x3f/0xb0
[<ffffffffa03901a8>] ? sync_inode_page+0xa8/0xd0 [f2fs]
[<ffffffffa038fdf7>] get_node_page+0x67/0x180 [f2fs]
[<ffffffffa039818b>] recover_fsync_data+0xacb/0xff0 [f2fs]
[<ffffffff816aaa1e>] ? _raw_spin_unlock+0x3e/0x40
[<ffffffffa0389634>] f2fs_fill_super+0x7d4/0x850 [f2fs]
[<ffffffff81184cf9>] mount_bdev+0x1c9/0x210
[<ffffffffa0388e60>] ? validate_superblock+0x180/0x180 [f2fs]
[<ffffffffa0387635>] f2fs_mount+0x15/0x20 [f2fs]
[<ffffffff81185a13>] mount_fs+0x43/0x1b0
[<ffffffff81145ba0>] ? __alloc_percpu+0x10/0x20
[<ffffffff811a0796>] vfs_kern_mount+0x76/0x120
[<ffffffff811a2cb7>] do_mount+0x237/0xa10
[<ffffffff81140b9b>] ? strndup_user+0x5b/0x80
[<ffffffff811a3520>] SyS_mount+0x90/0xe0
[<ffffffff816b3502>] system_call_fastpath+0x16/0x1b
The bug is triggered when check_index_in_prev_nodes tries to get the direct
node page by calling get_node_page.
At this point, if the direct node page is already locked by get_dnode_of_data,
its caller, we got a deadlock condition.
This patch adds additional condition check for the reuse of locked direct node
pages prior to the get_node_page call.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
While an orphan inode has zero link_count, f2fs_gc is able to select the inode
for foreground gc.
- f2fs_gc
- do_garbage_collect
- gc_data_segment
: f2fs_iget is failed
: get_valid_blocks() != 0, so that retry
--> here we got the infinite loop.
This patch resolved this issue.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If we met an error during the dentry recovery, we should not conduct checkpoint.
Otherwise, some errorneous dentry blocks overwrites the existing blocks that
contain the remaining recovery information.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The allocated page used by the recovery is not on HIGHMEM, so that we don't
need to use kmap/kunmap.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Few things can be changed in the default mkwrite function
1) Make file_update_time at the start before acquiring any lock
2) the condition page_offset(page) >= i_size_read(inode) should be
changed to page_offset(page) > i_size_read
3) Move wait_on_page_writeback.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We can do this, since now we use a global mutex, f2fs_stat_mutex to protect its
list operations.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
[Jaegeuk Kim: add description]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Majianpeng reported a lockdep splat for f2fs. It turns out mutex_lock_all()
acquires an array of locks (in global/local lock style).
Any such operation is always serialized using cp_mutex, therefore there is no
fs_lock[] lock-order issue; tell lockdep about this using the
mutex_lock_nest_lock() primitive.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
I found a bug when testing power-off-recovery as follows.
[Bug Scenario]
1. create a file
2. fsync the file
3. reboot w/o any sync
4. try to recover the file
- found its fsync mark
- found its dentry mark
: try to recover its dentry
- get its file name
- get its parent inode number
: here we got zero value
The reason why we get the wrong parent inode number is that we didn't
synchronize the inode page with its newly created inode information perfectly.
Especially, previous f2fs stores fi->i_pino and writes it to the cached
node page in a wrong order, which incurs the zero-valued i_pino during the
recovery.
So, this patch modifies the creation flow to fix the synchronization order of
inode page with its inode.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If get_dnode_of_data gets a locked node page, let's skip redundant
get_node_page calls.
This is for the futher enhancement.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
During the dentry recovery routine, recover_inode() triggers __f2fs_add_link
with its directory inode.
In the following scenario, a bug is captured.
1. dir = f2fs_iget(pino)
2. __f2fs_add_link(dir, name)
3. iput(dir)
-> f2fs_evict_inode() faces with BUG_ON(atomic_read(fi->dirty_dents))
Kernel BUG at ffffffffa01c0676 [verbose debug info unavailable]
[<ffffffffa01c0676>] f2fs_evict_inode+0x276/0x300 [f2fs]
Call Trace:
[<ffffffff8118ea00>] evict+0xb0/0x1b0
[<ffffffff8118f1c5>] iput+0x105/0x190
[<ffffffffa01d2dac>] recover_fsync_data+0x3bc/0x1070 [f2fs]
[<ffffffff81692e8a>] ? io_schedule+0xaa/0xd0
[<ffffffff81690acb>] ? __wait_on_bit_lock+0x7b/0xc0
[<ffffffff8111a0e7>] ? __lock_page+0x67/0x70
[<ffffffff81165e21>] ? kmem_cache_alloc+0x31/0x140
[<ffffffff8118a502>] ? __d_instantiate+0x92/0xf0
[<ffffffff812a949b>] ? security_d_instantiate+0x1b/0x30
[<ffffffff8118a5b4>] ? d_instantiate+0x54/0x70
This means that we should flush all the dentry pages between iget and iput().
But, during the recovery routine, it is unallowed due to consistency, so we
have to wait the whole recovery process.
And then, write_checkpoint flushes all the dirty dentry blocks, and nicely we
can put the stale dir inodes from the dirty_dir_inode_list.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The reason of using sbi->por_doing is to alleviate data writes during the
recovery.
The find_fsync_dnodes() produces some dirty dentry pages, so we should
cover it too with sbi->por_doing.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In get_lock_data_page, if there is a data race between get_dnode_of_data for
node and grab_cache_page for data, f2fs is able to face with the following
BUG_ON(dn.data_blkaddr == NEW_ADDR).
kernel BUG at /home/zeus/f2fs_test/src/fs/f2fs/data.c:251!
[<ffffffffa044966c>] get_lock_data_page+0x1ec/0x210 [f2fs]
Call Trace:
[<ffffffffa043b089>] f2fs_readdir+0x89/0x210 [f2fs]
[<ffffffff811a0920>] ? fillonedir+0x100/0x100
[<ffffffff811a0920>] ? fillonedir+0x100/0x100
[<ffffffff811a07f8>] vfs_readdir+0xb8/0xe0
[<ffffffff811a0b4f>] sys_getdents+0x8f/0x110
[<ffffffff816d7999>] system_call_fastpath+0x16/0x1b
This bug is able to be occurred when the block address of the data block is
changed after f2fs_put_dnode().
In order to avoid that, this patch fixes the lock order of node and data
blocks in which the node block lock is covered by the data block lock.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Currently f2fs recovers the dentry of fsynced files.
When power-off-recovery is conducted, this newly recovered inode should increase
node block count as well as inode block count.
This patch resolves this inconsistency that results in:
1. create a file
2. write data
3. fsync
4. reboot without sync
5. mount and recover the file
6. node block count is 1 and inode block count is 2
: fall into the inconsistent state
7. unlink the file
: trigger the following BUG_ON
------------[ cut here ]------------
kernel BUG at /home/zeus/f2fs_test/src/fs/f2fs/f2fs.h:716!
Call Trace:
[<ffffffffa0344100>] ? get_node_page+0x50/0x1a0 [f2fs]
[<ffffffffa0344bfc>] remove_inode_page+0x8c/0x100 [f2fs]
[<ffffffffa03380f0>] ? f2fs_evict_inode+0x180/0x2d0 [f2fs]
[<ffffffffa033812e>] f2fs_evict_inode+0x1be/0x2d0 [f2fs]
[<ffffffff811c7a67>] evict+0xa7/0x1a0
[<ffffffff811c82b5>] iput+0x105/0x190
[<ffffffff811c2b30>] d_kill+0xe0/0x120
[<ffffffff811c2c57>] dput+0xe7/0x1e0
[<ffffffff811acc3d>] __fput+0x19d/0x2d0
[<ffffffff811acd7e>] ____fput+0xe/0x10
[<ffffffff81070645>] task_work_run+0xb5/0xe0
[<ffffffff81002941>] do_notify_resume+0x71/0xb0
[<ffffffff8175f14a>] int_signal+0x12/0x17
Reported-and-Tested-by: Chris Fries <C.Fries@motorola.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Currently there is no way to truncate partial page where the end
truncate point is not at the end of the page. This is because it was not
needed and the functionality was enough for file system truncate
operation to work properly. However more file systems now support punch
hole feature and it can benefit from mm supporting truncating page just
up to the certain point.
Specifically, with this functionality truncate_inode_pages_range() can
be changed so it supports truncating partial page at the end of the
range (currently it will BUG_ON() if 'end' is not at the end of the
page).
This commit changes the invalidatepage() address space operation
prototype to accept range to be invalidated and update all the instances
for it.
We also change the block_invalidatepage() in the same way and actually
make a use of the new length argument implementing range invalidation.
Actual file system implementations will follow except the file systems
where the changes are really simple and should not change the behaviour
in any way .Implementation for truncate_page_range() which will be able
to accept page unaligned ranges will follow as well.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Hugh Dickins <hughd@google.com>
This patch-set includes the following major enhancement patches.
o introduce a new gloabl lock scheme
o add tracepoints on several major functions
o fix the overall cleaning process focused on victim selection
o apply the block plugging to merge IOs as much as possible
o enhance management of free nids and its list
o enhance the readahead mode for node pages
o address several cretical deadlock conditions
o reduce lock_page calls
The other minor bug fixes and enhancements are as follows.
o calculation mistakes: overflow
o bio types: READ, READA, and READ_SYNC
o fix the recovery flow, data races, and null pointer errors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hqii
-----END PGP SIGNATURE-----
Merge tag 'f2fs-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"This patch-set includes the following major enhancement patches.
- introduce a new gloabl lock scheme
- add tracepoints on several major functions
- fix the overall cleaning process focused on victim selection
- apply the block plugging to merge IOs as much as possible
- enhance management of free nids and its list
- enhance the readahead mode for node pages
- address several cretical deadlock conditions
- reduce lock_page calls
The other minor bug fixes and enhancements are as follows.
- calculation mistakes: overflow
- bio types: READ, READA, and READ_SYNC
- fix the recovery flow, data races, and null pointer errors"
* tag 'f2fs-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (68 commits)
f2fs: cover free_nid management with spin_lock
f2fs: optimize scan_nat_page()
f2fs: code cleanup for scan_nat_page() and build_free_nids()
f2fs: bugfix for alloc_nid_failed()
f2fs: recover when journal contains deleted files
f2fs: continue to mount after failing recovery
f2fs: avoid deadlock during evict after f2fs_gc
f2fs: modify the number of issued pages to merge IOs
f2fs: remove useless #include <linux/proc_fs.h> as we're now using sysfs as debug entry.
f2fs: fix inconsistent using of NM_WOUT_THRESHOLD
f2fs: check truncation of mapping after lock_page
f2fs: enhance alloc_nid and build_free_nids flows
f2fs: add a tracepoint on f2fs_new_inode
f2fs: check nid == 0 in add_free_nid
f2fs: add REQ_META about metadata requests for submit
f2fs: give a chance to merge IOs by IO scheduler
f2fs: avoid frequent background GC
f2fs: add tracepoints to debug checkpoint request
f2fs: add tracepoints for write page operations
f2fs: add tracepoints to debug the block allocation
...
After build_free_nids() searches free nid candidates from nat pages and
current journal blocks, it checks all the candidates if they are allocated
so that the nat cache has its nid with an allocated block address.
In this procedure, previously we used
list_for_each_entry_safe(fnid, next_fnid, &nm_i->free_nid_list, list).
But, this is not covered by free_nid_list_lock, resulting in null pointer bug.
This patch moves this checking routine inside add_free_nid() in order not to use
the spin_lock.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When nm_i->fcnt > 2 * MAX_FREE_NIDS, stop scanning other NAT entries.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
[Jaegeuk Kim: fix handling the return value of add_free_nid()]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch does two cleanups:
1. remove unused variable "fcnt" in build_free_nids().
2. make scan_nat_page() as void type and remove useless variable "fcnt".
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Directly drop the free_nid cache when nm_i->fcnt > 2 * MAX_FREE_NIDS
Since there is NOT nmi->free_nid_list_lock spinlock protection between
a sequential calling of alloc_nid() and alloc_nid_failed(), some other
threads may already add new free_nid to the free_nid_list during this
period.
We need to make sure nmi->fcnt is never > 2 * MAX_FREE_NIDS.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
[Jaegeuk Kim: fit the coding style]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When recovering a journal file with fsync data for files that have
been deleted, don't bail out on recovery.
Signed-off-by: Chris Fries <C.Fries@motorola.com>
Reviewed-by: Russell Knize <rknize2@motorola.com>
Reviewed-by: Jason Hrycay <jason.hrycay@motorola.com>
[Jaegeuk Kim: fit the coding style]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When unable to roll forward the journal, we shouldn't bail out and
not mount, we should continue to attempt the mount. Bad recovery data
is likely unrecoverable at this point, and requiring the user to try
to mount again doesn't solve any issues.
Signed-off-by: Chris Fries <C.Fries@motorola.com>
Reviewed-by: Russell Knize <rknize2@motorola.com>
Reviewed-by: Jason Hrycay <jason.hrycay@motorola.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
o Deadlock case #1
Thread 1:
- writeback_sb_inodes
- do_writepages
- f2fs_write_data_pages
- write_cache_pages
- f2fs_write_data_page
- f2fs_balance_fs
- wait mutex_lock(gc_mutex)
Thread 2:
- f2fs_balance_fs
- mutex_lock(gc_mutex)
- f2fs_gc
- f2fs_iget
- wait iget_locked(inode->i_lock)
Thread 3:
- do_unlinkat
- iput
- lock(inode->i_lock)
- evict
- inode_wait_for_writeback
o Deadlock case #2
Thread 1:
- __writeback_single_inode
: set I_SYNC
- do_writepages
- f2fs_write_data_page
- f2fs_balance_fs
- f2fs_gc
- iput
- evict
- inode_wait_for_writeback(I_SYNC)
In order to avoid this, even though iput is called with the zero-reference
count, we need to stop the eviction procedure if the inode is on writeback.
So this patch links f2fs_drop_inode which checks the I_SYNC flag.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
When testing f2fs on an SSD, I found some 128 page IOs followed by 1 page IO
were issued by f2fs_write_node_pages.
This means that there were some mishandling flows which degrades performance.
Previous f2fs_write_node_pages determines the number of pages to be written,
nr_to_write, as follows.
1. The bio_get_nr_vecs returns 129 pages.
2. The bio_alloc makes a room for 128 pages.
3. The initial 128 pages go into one bio.
4. The existing bio is submitted, and a new bio is prepared for the last 1 page.
5. Finally, sync_node_pages submits the last 1 page bio.
The problem is from the use of bio_get_nr_vecs, so this patch replace it
with max_hw_blocks using queue_max_sectors.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
try_to_free_nats() is usually called with parameter nr_shrink as
"nm_i->nat_cnt - NM_WOUT_THRESHOLD"
by flush_nat_entries() during checkpointing process.
However, this is inconsistent with the actual threshold check as
"if (nm_i->nat_cnt < 2 * NM_WOUT_THRESHOLD)"
, which will ignore the free_nats requests when
NM_WOUT_THRESHOLD < nm_i->nat_cnt < 2 * NM_WOUT_THRESHOLD
So fix the threshold check condition.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We call lock_page when we need to update a page after readpage.
Between grab and lock page, the page can be truncated by other thread.
So, we should check the page after lock_page whether it was truncated or not.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In order to avoid build_free_nid lock contention, let's change the order of
function calls as follows.
At first, check whether there is enough free nids.
- If available, just get a free nid with spin_lock without any overhead.
- Otherwise, conduct build_free_nids.
: scan nat pages, journal nat entries, and nat cache entries.
We should consider carefullly not to serve free nids intermediately made by
build_free_nids.
We can get stable free nids only after build_free_nids is done.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This can help when debugging the free nid allocation flows.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
It is more obvious that add_free_nid checks whether the free nid is zero or not.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Adding REQ_META for all the metadata requests can help in improving the
FS performance, if the underlying device supports TAGGING.
So, when considering the submit_bio path for all the f2fs requests. We can
add REQ_META for all the META requests.
As a precursor to this change we considered the commit
4265900e0b 'mmc: MMC-4.5 Data Tag Support'
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If there is no victim segments selected by background GC, let's wait
a little bit longer time to collect dirty segments.
By default, let's give 5 minutes.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add tracepoints to debug the various page write operation
like data pages, meta pages.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
[Jaegeuk: remove unnecessary tracepoints]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add tracepoints for tracing the garbage collector
threads in f2fs with status of collection & type.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
[Jaegeuk: modify slightly to show information]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
add tracepoints for tracing the truncate operations
like truncate node/data blocks, f2fs_truncate etc.
Tracepoints are added at entry and exit of operation
to trace the success & failure of operation.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
[Jaegeuk: combine and modify the tracepoint structures]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add tracepoints in f2fs for tracing the syncing
operations like filesystem sync, file sync enter/exit.
It will helf to trace the code under debugging scenarios.
Also add tracepoints for tracing the various inode operations
like building inode, eviction of inode, link/unlike of
inodes.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
[Jaegeuk: combine and modify the tracepoint structures]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The code conditions put inside the function is_multimedia_file are
reverse to the name i.e, we need to negate the return to actually
check if the file is a multimedia file. So, change the code and usage
path to align both the name and comparision conditions.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Introduce by commit c0d39e(f2fs: fix return values from validate superblock)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Fix typo mistakes.
1. I think that it should be 'L' instead of 'V'.
2. and try to fix 'Front' instead of 'Frone'
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In order to be aware of prefree and free sections during FG_GC, let's start with
write_checkpoint().
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If (ofs % (NIDS_PER_BLOCK + 1) == 0), the node is an indirect node block.
Signed-off-by: Zhihui Zhang <zzhsuny@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In the previous version, f2fs uses global locks according to the usage types,
such as directory operations, block allocation, block write, and so on.
Reference the following lock types in f2fs.h.
enum lock_type {
RENAME, /* for renaming operations */
DENTRY_OPS, /* for directory operations */
DATA_WRITE, /* for data write */
DATA_NEW, /* for data allocation */
DATA_TRUNC, /* for data truncate */
NODE_NEW, /* for node allocation */
NODE_TRUNC, /* for node truncate */
NODE_WRITE, /* for node write */
NR_LOCK_TYPE,
};
In that case, we lose the performance under the multi-threading environment,
since every types of operations must be conducted one at a time.
In order to address the problem, let's share the locks globally with a mutex
array regardless of any types.
So, let users grab a mutex and perform their jobs in parallel as much as
possbile.
For this, I propose a new global lock scheme as follows.
0. Data structure
- f2fs_sb_info -> mutex_lock[NR_GLOBAL_LOCKS]
- f2fs_sb_info -> node_write
1. mutex_lock_op(sbi)
- try to get an avaiable lock from the array.
- returns the index of the gottern lock variable.
2. mutex_unlock_op(sbi, index of the lock)
- unlock the given index of the lock.
3. mutex_lock_all(sbi)
- grab all the locks in the array before the checkpoint.
4. mutex_unlock_all(sbi)
- release all the locks in the array after checkpoint.
5. block_operations()
- call mutex_lock_all()
- sync_dirty_dir_inodes()
- grab node_write
- sync_node_pages()
Note that,
the pairs of mutex_lock_op()/mutex_unlock_op() and
mutex_lock_all()/mutex_unlock_all() should be used together.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Move the f2fs_balance_fs out of the truncate_hole function and only
perform that in punch_hole use case. The commit:
ed60b1644e7f7e5dd67d21caf7e4425dff05dad0
intended to do this but moved it into truncate_hole to cover more
cases. However, a deadlock scenario is possible when deleting an inode
entry under specific conditions:
f2fs_delete_entry()
mutex_lock_op(sbi, DENTRY_OPS);
truncate_hole()
f2fs_balance_fs()
mutex_lock(&sbi->gc_mutex);
f2fs_gc()
write_checkpoint()
block_operations()
mutex_lock_op(sbi, DENTRY_OPS);
Lets move it into the punch_hole case to cover the original intent of
avoiding it during fallocate's expand_inode_data case.
Change-Id: I29f8ea1056b0b88b70ba8652d901b6e8431bb27e
Signed-off-by: Jason Hrycay <jason.hrycay@motorola.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch reduces redundant spin_lock operations in alloc_nid_failed().
The alloc_nid_failed() does not need to delete entry and add one again
by triggering spin_lock and spin_unlock redundantly.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Commit - fa9150a84c - replaces a call to generic_writepages() in
f2fs_write_data_pages() with write_cache_pages(), with a function pointer
argument pointing to routine: __f2fs_writepage.
-> https://git.kernel.org/linus/fa9150a84ca333f68127097c4fa1eda4b3913a22
This patch adds a NULL pointer check in f2fs_write_data_pages() to avoid
a possible NULL pointer dereference, in case if - mapping->a_ops->writepage -
is NULL.
Signed-off-by: P J P <ppandit@redhat.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Like below, there are 8 segment bitmaps for SSR victim candidates.
enum dirty_type {
DIRTY_HOT_DATA, /* dirty segments assigned as hot data logs */
DIRTY_WARM_DATA, /* dirty segments assigned as warm data logs */
DIRTY_COLD_DATA, /* dirty segments assigned as cold data logs */
DIRTY_HOT_NODE, /* dirty segments assigned as hot node logs */
DIRTY_WARM_NODE, /* dirty segments assigned as warm node logs */
DIRTY_COLD_NODE, /* dirty segments assigned as cold node logs */
DIRTY, /* to count # of dirty segments */
PRE, /* to count # of entirely obsolete segments */
NR_DIRTY_TYPE
};
The upper 6 bitmaps indicates segments dirtied by active log areas respectively.
And, the DIRTY bitmap integrates all the 6 bitmaps.
For example,
o DIRTY_HOT_DATA : 1010000
o DIRTY_WARM_DATA: 0100000
o DIRTY_COLD_DATA: 0001000
o DIRTY_HOT_NODE : 0000010
o DIRTY_WARM_NODE: 0000001
o DIRTY_COLD_NODE: 0000000
In this case,
o DIRTY : 1111011,
which means that we should guarantee the consistency between DIRTY and other
bitmaps concreately.
However, the SSR mode selects victims freely from any log types, which can set
multiple bits across the various bitmap types.
So, this patch eliminates this inconsistency.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In order to do GC more reliably, I'd like to lock the vicitm summary page
until its GC is completed, and also prevent any checkpoint process.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a new condition that allocates free segments in the current
active section even if SSR is needed.
Otherwise, f2fs cannot allocate remained free segments in the section since
SSR finds dirty segments only.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The foreground GCs are triggered under not enough free sections.
So, we should not skip moving valid blocks in the victim segments.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch removes a bitmap for victim segments selected by foreground GC, and
modifies the other bitmap for victim segments selected by background GC.
1) foreground GC bitmap
: We don't need to manage this, since we just only one previous victim section
number instead of the whole victim history.
The f2fs uses the victim section number in order not to allocate currently
GC'ed section to current active logs.
2) background GC bitmap
: This bitmap is used to avoid selecting victims repeatedly by background GCs.
In addition, the victims are able to be selected by foreground GCs, since
there is no need to read victim blocks during foreground GCs.
By the fact that the foreground GC reclaims segments in a section unit, it'd
be better to manage this bitmap based on the section granularity.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When allocating a new segment under the LFS mode, we should keep the section
boundary.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In get_node_page, we do not need to call lock_page all the time.
If the node page is cached as uptodate,
1. grab_cache_page locks the page,
2. read_node_page unlocks the page, and
3. lock_page is called for further process.
Let's avoid this.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Let's use a macro to get the total number of sections.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
A macro should not use duplicate parameter names.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Use kmemdup instead of kzalloc and memcpy.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Acked-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When we recover fsync'ed data after power-off-recovery, we should guarantee
that any parent inode number should be correct for each direct inode blocks.
So, let's make the following rules.
- The fsync should do checkpoint to all the inodes that were experienced hard
links.
- So, the only normal files can be recovered by roll-forward.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In the checkpoint flow, the f2fs investigates the total nat cache entries.
Previously, if an entry has NULL_ADDR, f2fs drops the entry and adds the
obsolete nid to the free nid list.
However, this free nid will be reused sooner, resulting in its nat entry miss.
In order to avoid this, we don't need to drop the nat cache entry at this moment.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch removes data_version check flow during the fsync call.
The original purpose for the use of data_version was to avoid writng inode
pages redundantly by the fsync calls repeatedly.
However, when user can modify file meta and then call fsync, we should not
skip fsync procedure.
So, let's remove this condition check and hope that user triggers in right
manner.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We should handle errors during the recovery flow correctly.
For example, if we get -ENOMEM, we should report a mount failure instead of
conducting the remained mount procedure.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In function check_nid_range, there is no need to trigger BUG_ON and make kernel stop.
Instead it could just check and indicate the inode number to be EINVAL.
Update the return path in do_read_inode to use the return from check_nid_range.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
[Jaegeuk: replace BUG_ON with WARN_ON]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
validate super block is not returning with proper values.
When failure from sb_bread it should reflect there is an EIO otherwise
it should return of EINVAL.
Returning, '1' is not conveying proper message as the return type.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
make use of F2FS_NAME_LEN for name length checking,
change return conditions at few places, by assigning
storing the errorvalue in 'error' and making a common
exit path.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Change f2fs so that a warning is emitted when an attempt is made to
mount a filesystem with the unsupported discard option.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The fsync call should be ended after flushing the in-device caches.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The build_free_nid should not add free nids over nm_i->max_nid.
But, there was a hole that invalid free nid was added by the following scenario.
Let's suppose nm_i->max_nid = 150 and the last NAT page has 100 ~ 200 nids.
build_free_nids
- get_current_nat_page loads the last NAT page
- scan_nat_page can add 100 ~ 200 nids
-> Bug here!
So, when scanning an NAT page, we should check each candidate whether it is
over max_nid or not.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If the return value of releasepage is equal to zero, the page cannot be reclaimed.
Instead, we should return 1 in order to reclaim clean pages.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When we build new free nids, let's scan the just next NAT page instead of
skipping a couple of previously scanned pages in order to reuse free nids in
there.
Otherwise, we can use too much wide range of nids even though several nids were
deallocated, and also their node pages can be cached in the node_inode's address
space.
This means that we can retain lots of clean pages in the main memory, which
induces mm's reclaiming overhead.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Currently, f2fs doesn't reclaim any node pages.
However, if we found that a node page was truncated by checking its block
address with zero during f2fs_write_node_page, we should not skip that node
page and return zero to reclaim it.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch reduces redundant locking and unlocking pages during read operations.
In f2fs_readpage, let's use wait_on_page_locked() instead of lock_page.
And then, when we need to modify any data finally, let's lock the page so that
we can avoid lock contention.
[readpage rule]
- The f2fs_readpage returns unlocked page, or released page too in error cases.
- Its caller should handle read error, -EIO, after locking the page, which
indicates read completion.
- Its caller should check PageUptodate after grab_cache_page.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In all the breaking conditions in get_node_path, 'n' is used to
track index in offset[] array, but while breaking out also, in all
paths n++ is done.
So, remove the ++ from breaking paths. Also, avoid
reset of 'level=0' in first case.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The maximum filename length supported in linux is 255 characters.
So let's follow that.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Optimize and change return path in lookup_free_nid_list
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We can remove the call to find_get_page to get a page from the cache
and check for up-to-date, instead we can make use of grab_cache_page
part itself to fetch the page from the cache.
So, removing the call and moving the PageUptodate at proper place, also
taken care of moving the lock_page condition in the page_hit part.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The caller of get_nid should be careful not to put lower value than
NODE_DIR1_BLOCK in case of level is zero.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, f2fs reads several node pages ahead when get_dnode_of_data is called
with RDONLY_NODE flag.
And, this flag is set by the following functions.
- get_data_block_ro
- get_lock_data_page
- do_write_data_page
- truncate_blocks
- truncate_hole
However, this readahead mechanism is initially introduced for the use of
get_data_block_ro to enhance the sequential read performance.
So, let's clarify all the cases with the additional modes as follows.
enum {
ALLOC_NODE, /* allocate a new node page if needed */
LOOKUP_NODE, /* look up a node without readahead */
LOOKUP_NODE_RA, /*
* look up a node with readahead called
* by get_datablock_ro.
*/
}
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
The get_node_page_ra tries to:
1. grab or read a target node page for the given nid,
2. then, call ra_node_page to read other adjacent node pages in advance.
So, when we try to read a target node page by #1, we should submit bio with
READ_SYNC instead of READA.
And, in #2, READA should be used.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
If the node page was truncated, its block address became zero.
This means that we don't need to write the node page, but have to unlock
NODE_WRITE, decrease the number of dirty node pages, and then unlock_page
before returning the f2fs_write_node_page with zero.
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Use div_u64 to fix overflow when calculating utilization.
*long int* is 4-bytes on 32-bit so (user blocks * 100) might be
overflow if disk size is over e.g. 512GB.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Modify the request_module to prefix the file system type with "fs-"
and add aliases to all of the filesystems that can be built as modules
to match.
A common practice is to build all of the kernel code and leave code
that is not commonly needed as modules, with the result that many
users are exposed to any bug anywhere in the kernel.
Looking for filesystems with a fs- prefix limits the pool of possible
modules that can be loaded by mount to just filesystems trivially
making things safer with no real cost.
Using aliases means user space can control the policy of which
filesystem modules are auto-loaded by editing /etc/modprobe.d/*.conf
with blacklist and alias directives. Allowing simple, safe,
well understood work-arounds to known problematic software.
This also addresses a rare but unfortunate problem where the filesystem
name is not the same as it's module name and module auto-loading
would not work. While writing this patch I saw a handful of such
cases. The most significant being autofs that lives in the module
autofs4.
This is relevant to user namespaces because we can reach the request
module in get_fs_type() without having any special permissions, and
people get uncomfortable when a user specified string (in this case
the filesystem type) goes all of the way to request_module.
After having looked at this issue I don't think there is any
particular reason to perform any filtering or permission checks beyond
making it clear in the module request that we want a filesystem
module. The common pattern in the kernel is to call request_module()
without regards to the users permissions. In general all a filesystem
module does once loaded is call register_filesystem() and go to sleep.
Which means there is not much attack surface exposed by loading a
filesytem module unless the filesystem is mounted. In a user
namespace filesystems are not mounted unless .fs_flags = FS_USERNS_MOUNT,
which most filesystems do not set today.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Reported-by: Kees Cook <keescook@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
This patch removes the following build warning:
fs/f2fs/node.c: warning: 'nofs' may be used uninitialized in this function
[-Wuninitialized]: => 738:8
Note that this is a false alarm.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Pull f2fs cleanup patches from Al Viro:
f2fs: get rid of fake on-stack dentries
f2fs: switch init_inode_metadata() to passing parent and name separately
f2fs: switch new_inode_page() from dentry to qstr
f2fs: init_dent_inode() should take qstr
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Conflicts:
fs/f2fs/recovery.c
adding compat_ioctl to provide support for backward comptability - 32bit binary
execution on 64bit kernel.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In the SSR case, the max gc cost should be the number of pages in a segment.
Otherwise, f2fs is able to fail getting dirty segments frequently for SSR.
In get_victim_by_default() previously,
while(1) {
...
cost = get_gc_cost(); <- cost is between 0 ~ 512.
...
if (cost == get_max_cost(sbi, &p)) <- max cost is UINT_MAX due to GC_CB type
continue;
if (nsearched++ >= MAX_VICTIM_SEARCH)
break;
}
So, if there are a number of fully valid segments in series, f2fs cannot skip
those segments by comparing the cost and max cost of each segment.
Note that, the cost is the number of valid blocks at the time of the last
checkpoint.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch makes clearer the ambiguous f2fs_gc flow as follows.
1. Remove intermediate checkpoint condition during f2fs_gc
(i.e., should_do_checkpoint() and GC_BLOCKED)
2. Remove unnecessary return values of f2fs_gc because of #1.
(i.e., GC_NODE, GC_OK, etc)
3. Simplify write_checkpoint() because of #2.
4. Clarify the main f2fs_gc flow.
o monitor how many freed sections during one iteration of do_garbage_collect().
o do GC more without checkpoints if we can't get enough free sections.
o do checkpoint once we've got enough free sections through forground GCs.
5. Adopt thread-logging (Slack-Space-Recycle) scheme more aggressively on data
log types. See. get_ssr_segement()
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Instead of evaluating the free_sections and then deciding to return
true/false from that path. We can directly use the evaluation condition
for returning proper value.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Introduce accessor to get the sections based upon the block type
(node,dents...) and modify the functions : should_do_checkpoint,
has_not_enough_free_secs to use this accessor function to get
the node sections and dent sections.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When gc thread creation is failed, mark gc_thread as NULL to avoid
crash while trying to stop invalid thread in stop_gc_thread->kthread_stop.
Instead make it return from:
if (!gc_th)
return;
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Currently GC task is started for each f2fs formatted/mounted device.
But, when we check the task list, using 'ps', there is no distinguishing
factor between the tasks. So, name the task as per the block device just
like the flusher threads.
Also, remove the macro GC_THREAD_NAME and instead use the name: f2fs_gc
to avoid name length truncation, as the command length is 16
-> TASK_COMM_LEN 16 and example name like:
f2fs_gc_task:8:16 -> this exceeds name length
Before Patch for 2 F2FS formatted partitions:
root 28061 0.0 0.0 0 0 ? S 10:31 0:00 [f2fs_gc_task]
root 28087 0.0 0.0 0 0 ? S 10:32 0:00 [f2fs_gc_task]
After Patch:
root 16756 0.0 0.0 0 0 ? S 14:57 0:00 [f2fs_gc-8:18]
root 16765 0.0 0.0 0 0 ? S 14:57 0:00 [f2fs_gc-8:19]
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
1. If f2fs is mounted with background_gc_off option, checking
BG_GC is not redundant.
2. f2fs_balance_fs is checked in f2fs_gc, so this is also redundant.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
F2FS_SET_SB_DIRT is called in inc_page_count and
it is directly called one more time in the next line.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In f2fs, there are two superblocks. So when the first superblock was
invalidate, it should try to check another.
By Jaegeuk Kim:
o Remove a white space for coding style
o Clean up for code readability
o Fix a typo
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In some system PAGE_CACHE_SIZE isn't 4K. So using F2FS_BLKSIZE to judge.
By Jaegeuk Kim:
o f2fs does not support no other 4KB page cache size.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In file status, it can't distinguish between different devices.
So add device name to do this function.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
1. Background
Previously, if f2fs tries to move data blocks of an *evicting* inode during the
cleaning process, it stops the process incompletely and then restarts the whole
process, since it needs a locked inode to grab victim data pages in its address
space. In order to get a locked inode, iget_locked() by f2fs_iget() is normally
used, but, it waits if the inode is on freeing.
So, here is a deadlock scenario.
1. f2fs_evict_inode() <- inode "A"
2. f2fs_balance_fs()
3. f2fs_gc()
4. gc_data_segment()
5. f2fs_iget() <- inode "A" too!
If step #1 and #5 treat a same inode "A", step #5 would fall into deadlock since
the inode "A" is on freeing. In order to resolve this, f2fs_iget_nowait() which
skips __wait_on_freeing_inode() was introduced in step #5, and stops f2fs_gc()
to complete f2fs_evict_inode().
1. f2fs_evict_inode() <- inode "A"
2. f2fs_balance_fs()
3. f2fs_gc()
4. gc_data_segment()
5. f2fs_iget_nowait() <- inode "A", then stop f2fs_gc() w/ -ENOENT
2. Problem and Solution
In the above scenario, however, f2fs cannot finish f2fs_evict_inode() only if:
o there are not enough free sections, and
o f2fs_gc() tries to move data blocks of the *evicting* inode repeatedly.
So, the final solution is to use f2fs_iget() and remove f2fs_balance_fs() in
f2fs_evict_inode().
The f2fs_evict_inode() actually truncates all the data and node blocks, which
means that it doesn't produce any dirty node pages accordingly.
So, we don't need to do f2fs_balance_fs() in practical.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Let's remove the use of page_cache_release() in f2fs, and instead, use
f2fs_put_page(page, 0) which is exactly same but for code readability.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In f2fs_inode_info structure, the description for data_version
has a typo mistake. It should be latest instead of lastes.
So, correcting that.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We can remove unneeded label unlock_out, avoid unnecessary jump
and reorganize the returning conditions in this function.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
After doing a write_checkpoint from garbage collection path if there is still
need to do more garbage collection, gc_more label is used to jump and start
the process again. And in that process, first step before getting victim is to
check if there are not enough free sections, which is already done before
doing a jump to gc_more. We can avoid the redundant call to check free
sections, by checking the gc_type flag which will remain FG_GC(value 1) under
this condition.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch supports ioctl FIFREEZE and FITHAW to snapshot filesystem.
Before calling f2fs_freeze, all writers would be suspended and sync_fs
would be completed. So no f2fs has to do something.
Just background gc operation should be skipped due to generate dirty
nodes and data until unfreeze.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
For the code
> prev = list_entry(orphan->list.prev, typeof(*prev), list);
if orphan->list.prev == head, it can't get the right prev.
And we can use the parameter 'this' to add.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
There is a typo in the ->show_options function for disable_ext_identify.
Fix it to match the spelling from the documentation.
Signed-off-by: Alejandro Martinez Ruiz <alex@nowcomputing.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The fill_zero() from fallocate() calls get_new_data_page() in which calls
reserve_new_block().
The reserve_new_block() should be covered by *DATA_NEW*, one of global locks.
And also, before getting the lock, we should check free sections by calling
f2fs_balance_fs().
If we break this rule, f2fs is able to face with out-of-control free space
management and fall into infinite loop like the following scenario as well.
[f2fs_sync_fs()] [fallocate()]
- write_checkpoint() - fill_zero()
- block_operations() - get_new_data_page()
: grab NODE_NEW - get_dnode_of_data()
: get locked dirty node page
- sync_node_pages()
: try to grab NODE_NEW for data allocation
: trylock and skip the dirty node page
: call sync_node_pages() repeatedly in order to flush all the dirty node
pages!
In order to avoid this, we should grab another global lock such as DATA_NEW
before calling get_new_data_page() in fill_zero().
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch enhances the checkpoint routine to cope with IO errors.
Basically f2fs detects IO errors from end_io_write, and the errors are able to
be occurred during one of data, node, and meta page writes.
In the previous code, when an IO error is occurred during writes, f2fs sets a
flag, CP_ERROR_FLAG, in the raw ckeckpoint buffer which will be written to disk.
Afterwards, write_checkpoint() will check the flag and remount f2fs as a
read-only (ro) mode.
However, even once f2fs is remounted as a ro mode, dirty checkpoint pages are
freely able to be written to disk by flusher or kswapd in background.
In such a case, after cold reboot, f2fs would restore the checkpoint data having
CP_ERROR_FLAG, resulting in disabling write_checkpoint and remounting f2fs as
a ro mode again.
Therefore, let's prevent any checkpoint page (meta) writes once an IO error is
occurred, and remount f2fs as a ro mode right away at that moment.
Reported-by: Oliver Winker <oliver@oli1170.net>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
This patch stores inode->i_rdev into on-disk inode structure.
Alun reported that:
aspire tmp # mount -t f2fs /dev/sdb mnt
aspire tmp # mknod mnt/sda1 b 8 1
aspire tmp # mknod mnt/null c 1 3
aspire tmp # mknod mnt/console c 5 1
aspire tmp # ls -l mnt
total 2
crw-r--r-- 1 root root 5, 1 Jan 22 18:44 console
crw-r--r-- 1 root root 1, 3 Jan 22 18:44 null
brw-r--r-- 1 root root 8, 1 Jan 22 18:44 sda1
aspire tmp # umount mnt
aspire tmp # mount -t f2fs /dev/sdb mnt
aspire tmp # ls -l mnt
total 2
crw-r--r-- 1 root root 0, 0 Jan 22 18:44 console
crw-r--r-- 1 root root 0, 0 Jan 22 18:44 null
brw-r--r-- 1 root root 0, 0 Jan 22 18:44 sda1
In this report, f2fs lost the major/minor numbers of device files after umount.
The reason was revealed that f2fs does not store the inode->i_rdev to the
on-disk inode data structure.
So, as the other file systems do, f2fs also stores i_rdev into the i_addr fields
in on-disk inode structure without any on-disk layout changes.
Note that, this bug is limited to device files made by mknod().
Reported-and-Tested-by: Alun Jones <alun.linux@ty-penguin.org.uk>
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
... sure, it's tempting to just pass dentry. Except that we don't
_have_ anything resembling a real dentry on one of the paths to it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
for one thing, it doesn't (and shouldn't) use anything else from dentry;
for another, on some call chains the dentry is fake and should
be eliminated completely.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This is calling list_del() inside a loop which is a problem when we try
move to the next item on the list. I've converted it to use the _safe
version. And also, as a cleanup, I've converted it to use
list_for_each_entry instead of list_for_each.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The caller of start_bidx_of_node() should give proper node offsets which
point only direct node blocks. Otherwise, it is a caller's bug.
This patch adds comments to make it clear.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If some small bios of dirty node pages are supposed to be issued during the
sequential data writes, there-in well-produced consecutive data bios are able
to be split by the small node bios, resulting in performance degradation.
So, let's collect a number of dirty node pages until reaching a threshold.
And, by default, I set the threshold as 2MB, a segment size.
This improves sequential write performance on i5, 512GB SSD (830 w/ SATA2) as
follows.
Before: 231 MB/s -> After: 255 MB/s
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
This patch adds f2fs_bmap operation to the data address space.
This enables f2fs to support swapfile.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This was added for all the file systems before.
See the following commit.
commit id: 0b173bc4da
[PATCH] mm: kill vma flag VM_CAN_NONLINEAR
This patch moves actual ptes filling for non-linear file mappings
into special vma operation: ->remap_pages().
File system must implement this method to get non-linear mappings support,
if it uses filemap_fault() then generic_file_remap_pages() can be used.
Now device drivers can implement this method and obtain nonlinear vma support."
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add __init to functions in init_f2fs_fs for code consistency.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
As the "status" debugfs entry will be maintained for entire F2FS filesystem
irrespective of the number of partitions.
So, we can move the initialization to the init part of the f2fs and destroy will
be done from exit part. After making changes, for individual partition mount -
entry creation code will not be executed.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
There is an race condition between umounting f2fs and reading f2fs/status, which
results in oops.
Fox example:
Thread A Thread B
umount f2fs cat f2fs/status
f2fs_destroy_stats() { stat_show() {
list_for_each_entry_safe(&f2fs_stat_list)
list_del(&si->stat_list);
mutex_lock(&si->stat_lock);
si->sbi = NULL;
mutex_unlock(&si->stat_lock);
kfree(sbi->stat_info);
} mutex_lock(&si->stat_lock) <- si is gone.
...
}
Solution with a global lock: f2fs_stat_mutex:
Thread A Thread B
umount f2fs cat f2fs/status
f2fs_destroy_stats() { stat_show() {
mutex_lock(&f2fs_stat_mutex);
list_del(&si->stat_list);
mutex_unlock(&f2fs_stat_mutex);
kfree(sbi->stat_info); mutex_lock(&f2fs_stat_mutex);
} list_for_each_entry_safe(&f2fs_stat_list)
...
mutex_unlock(&f2fs_stat_mutex);
}
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
[jaegeuk.kim@samsung.com: fix typos, description, and remove the existing lock]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Let's consider the usage of blk_plug in f2fs_write_data_pages().
We can come up with the two issues: lock contention and task awareness.
1. Merging bios prior to grabing "queue lock"
The f2fs merges consecutive IOs in the file system level before
submitting any bios, which is similar with the back merge by the
plugging mechanism in attempt_plug_merge(). Both of them need to acquire
no queue lock.
2. Merging policy with respect to tasks
The f2fs merges IOs as much as possible regardless of tasks, while
blk-plugging is conducted on a basis of tasks. As we can understand
there are trade-offs, f2fs tries to maximize the write performance with
well-merged bios.
As a result, if f2fs produces many consecutive but separated bios in
writepages(), it would be good to use blk-plugging since f2fs would be
able to avoid queue lock contention in the block layer by merging them.
But, f2fs merges IOs and submit one bio, which means that there are not
much chances to merge bios by attempt_plug_merge().
However, f2fs has already been used blk_plug by triggering generic_writepages()
in f2fs_write_data_pages().
So to make the overall code consistency, I'd like to remove blk_plug there.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In call to f2fs_delete_entry, 'dir' time modification code is put
at two places.
So, remove the redundant code for timing update.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Since, f2fs supports only 4KB blocksize, which is set at the beginning in
f2fs_fill_super. So, we do not need to again check this blocksize setting
in such case.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The f2fs_fallocate() has two operations: punch_hole and expand_size.
Only in the case of punch_hole, dirty node pages can be produced, so let's
trigger f2fs_balance_fs() in this case only.
Furthermore, let's trigger it at every data truncation routine.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The f2fs_balance_fs() is to check the number of free sections and decide whether
it needs to conduct cleaning or not. If there are not enough free sections, the
cleaning job should be started.
In order to control an amount of free sections even under high utilization, f2fs
should call f2fs_balance_fs at all the VFS interfaces that are able to produce
dirty pages.
This patch adds the function calls in the missing interfaces as follows.
1. f2fs_setxattr()
The f2fs_setxattr() produces dirty node pages so that we should call
f2fs_balance_fs() either likewise doing in other VFS interfaces such as
f2fs_lookup(), f2fs_mkdir(), and so on.
2. f2fs_sync_file()
We should guarantee serving free sections for syncing metadata during fsync.
Previously, there is no space check before triggering checkpoint and
sync_node_pages.
Therefore, if a bunch of fsync calls are triggered under 100% of FS utilization,
f2fs is able to be faced with no free sections, resulting in BUG_ON().
3. f2fs_sync_fs()
Before calling write_checkpoint(), we should guarantee that there are minimum
free sections.
4. f2fs_write_inode()
f2fs_write_inode() is also able to produce dirty node pages.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
I'd like to revisit the f2fs_gc flow and rewrite as follows.
1. In practical, the nGC parameter of f2fs_gc is meaningless. So, let's
remove it.
2. Background GC marks victim blocks as dirty one at a time.
3. Foreground GC should do cleaning job until acquiring enough free
sections. Afterwards, it needs to do checkpoint.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch resolves Coverity #753102:
>>> No check of the return value of "f2fs_add_link(&dent, inode)".
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch resolves Coverity #753112.
In practical, the existing code flow does not fall into the reported errorneous
path. But, anyway, let's avoid this for future.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Update partition info output under debug FS to reflect segment layout correctly.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
While creating a new entry for addition to the list(orphan inode list
and fsync inode entry list), there is no need to call HEAD initialization
for these entries. So, remove that init part.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
After doing a punch hole or expanding inode doing fallocation.
The change and modification time are not update for the file.
So, update time after no issue is observed in fallocate.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Introduced f2fs_msg function to differentiate f2fs specific messages in
the log. And, added few informative prints in the mount path, to convey
proper error in case of mount failure.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch-set includes two major bug fixes:
- incorrect IUsed provided by *df -i*, and
- lookup failure of parent inodes in corner cases.
[Other Bug Fixes]
- Fix error handling routines
- Trigger recovery process correctly
- Resolve build failures due to missing header files
[Etc]
- Add a MAINTAINERS entry for f2fs
- Fix and clean up variables, functions, and equations
- Avoid warnings during compilation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=dH3T
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs bug fixes from Jaegeuk Kim:
"This patch-set includes two major bug fixes:
- incorrect IUsed provided by *df -i*, and
- lookup failure of parent inodes in corner cases.
[Other Bug Fixes]
- Fix error handling routines
- Trigger recovery process correctly
- Resolve build failures due to missing header files
[Etc]
- Add a MAINTAINERS entry for f2fs
- Fix and clean up variables, functions, and equations
- Avoid warnings during compilation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs:
f2fs: unify string length declarations and usage
f2fs: clean up unused variables and return values
f2fs: clean up the start_bidx_of_node function
f2fs: remove unneeded variable from f2fs_sync_fs
f2fs: fix fsync_inode list addition logic and avoid invalid access to memory
f2fs: remove unneeded initialization of nr_dirty in dirty_seglist_info
f2fs: handle error from f2fs_iget_nowait
f2fs: fix equation of has_not_enough_free_secs()
f2fs: add MAINTAINERS entry
f2fs: return a default value for non-void function
f2fs: invalidate the node page if allocation is failed
f2fs: add missing #include <linux/prefetch.h>
f2fs: do f2fs_balance_fs in front of dir operations
f2fs: should recover orphan and fsync data
f2fs: fix handling errors got by f2fs_write_inode
f2fs: fix up f2fs_get_parent issue to retrieve correct parent inode number
f2fs: fix wrong calculation on f_files in statfs
f2fs: remove set_page_dirty for atomic f2fs_end_io_write
This patch is intended to unify string length declarations and usage.
There are number of calls to strlen which return size_t object.
The size of this object depends on compiler if it will be bigger,
equal or even smaller than an unsigned int
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch also resolves the following warning reported by kbuild test robot.
fs/f2fs/gc.c: In function 'start_bidx_of_node':
fs/f2fs/gc.c:453:21: warning: 'bidx' may be used uninitialized in this function
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We can directly return '0' from the function, instead of introducing a
'ret' variable.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In function find_fsync_dnodes() - the fsync inodes gets added to the list, but
in one path suppose f2fs_iget results in error, in such case - error gets added
to the fsync inode list.
In next call to recover_data()->get_fsync_inode()
entry = list_entry(this, struct fsync_inode_entry, list);
if (entry->inode->i_ino == ino)
This can result in "invalid access to memory" when it encounters 'error' as
entry in the fsync inode list.
So, add the fsync inode entry to the list only in case of no errors.
And, free the object at that point itself in case of issue.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Since, the memory for the object of dirty_seglist_info is allocated
using kzalloc - which returns zeroed out memory. So, there is no need
to initialize the nr_dirty values with zeroes.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In case f2fs_iget_nowait returns error, it results in truncate_hole being
called with 'error' value as inode pointer. There is no check in truncate_hole
for valid inode, so it could result in crash due "invalid access to memory".
Avoid this by handling error condition properly.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Practically, has_not_enough_free_secs() should calculate with the numbers of
current node and directory data blocks together.
Actually the equation was implemented in need_to_flush().
So, this patch removes need_flush() and moves the equation into
has_not_enough_free_secs().
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch resolves a build warning reported by kbuild test robot.
"
fs/f2fs/segment.c: In function '__get_segment_type':
fs/f2fs/segment.c:806:1: warning: control reaches end of non-void
function [-Wreturn-type]
"
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The new_node_page() is processed as the following procedure.
1. A new node page is allocated.
2. Set PageUptodate with proper footer information.
3. Check if there is a free space for allocation
4.a. If there is no space, f2fs returns with -ENOSPC.
4.b. Otherwise, go next.
In the case of step #4.a, f2fs remains a wrong node page in the page cache
with the uptodate flag.
Also, even though a new node page is allocated successfully, an error can be
occurred afterwards due to allocation failure of the other data structures.
In such a case, remove_inode_page() would be triggered, so that we have to
clear uptodate flag in truncate_node() too.
So, we should remove the uptodate flag, if allocation is failed.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
m68k allmodconfig:
fs/f2fs/data.c: In function ‘read_end_io’:
fs/f2fs/data.c:311: error: implicit declaration of function ‘prefetchw’
fs/f2fs/segment.c: In function ‘f2fs_end_io_write’:
fs/f2fs/segment.c:628: error: implicit declaration of function ‘prefetchw’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
With user namespaces enabled building f2fs fails with:
CC fs/f2fs/acl.o
fs/f2fs/acl.c: In function ‘f2fs_acl_from_disk’:
fs/f2fs/acl.c:85:21: error: ‘struct posix_acl_entry’ has no member named ‘e_id’
make[2]: *** [fs/f2fs/acl.o] Error 1
make[2]: Target `__build' not remade because of errors.
e_id is a backwards compatibility field only used for file systems
that haven't been converted to use kuids and kgids. When the posix
acl tag field is neither ACL_USER nor ACL_GROUP assigning e_id is
unnecessary. Remove the assignment so f2fs will build with user
namespaces enabled.
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Amit Sahrawat <a.sahrawat@samsung.com>
Acked-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
In order to conserve free sections to deal with the worst-case scenarios, f2fs
should be able to freeze all the directory operations especially when there are
not enough free sections. The f2fs_balance_fs() is for this use.
When FS utilization becomes almost 100%, directory operations can be failed due
to -ENOSPC frequently, which produces some dirty node pages occasionally.
Previously, in such a case, f2fs_balance_fs() is not able to be triggered since
it is triggered only if the directory operation ends up with success.
So, this patch triggers f2fs_balance_fs() at first before handling directory
operations.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Ruslan reported that f2fs hangs with an infinite loop in f2fs_sync_file():
while (sync_node_pages(sbi, inode->i_ino, &wbc) == 0)
f2fs_write_inode(inode, NULL);
The reason was revealed that the cold flag is not set even thought this inode is
a normal file. Therefore, sync_node_pages() skips to write node blocks since it
only writes cold node blocks.
The cold flag is stored to the node_footer in node block, and whenever a new
node page is allocated, it is set according to its file type, file or directory.
But, after sudden-power-off, when recovering the inode page, f2fs doesn't recover
its cold flag.
So, let's assign the cold flag in more right places.
One more thing:
If f2fs_write_inode() returns an error due to whatever situations, there would
be no dirty node pages so that sync_node_pages() returns zero.
(i.e., zero means nothing was written.)
Reported-by: Ruslan N. Marchenko <me@ruff.mobi>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Test Case:
[NFS Client]
ls -lR .
[NFS Server]
while [ 1 ]
do
echo 3 > /proc/sys/vm/drop_caches
done
Error on NFS Client: "No such file or directory"
When cache is dropped at the server, it results in lookup failure at the
NFS client due to non-connection with the parent. The default path is it
initiates a lookup by calculating the hash value for the name, even though
the hash values stored on the disk for "." and ".." is maintained as zero,
which results in failure from find_in_block due to not matching HASH values.
Fix up, by using the correct hashing values for these entries.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In f2fs_statfs(), f_files should be the total number of available inodes
instead of the currently allocated inodes.
So, this patch should resolve the reported bug below.
Note that, showing 10% usage is not a bug, since f2fs reveals whole volume size
as much as possible and shows the space overhead as *used*.
This policy is fair enough with respect to other file systems.
<Reported Bug>
(loop0 is backed by 1GiB file)
$ mkfs.f2fs /dev/loop0
F2FS-tools: Ver: 1.1.0 (2012-12-11)
Info: sector size = 512
Info: total sectors = 2097152 (in 512bytes)
Info: zone aligned segment0 blkaddr: 512
Info: format successful
$ mount /dev/loop0 mnt/
$ df mnt/
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/loop0 1046528 98312 929784 10%
/home/zeta/linux-devel/mtd-bench/mnt
$ df mnt/ -i
Filesystem Inodes IUsed IFree IUse% Mounted on
/dev/loop0 1 -465918 465919 - /home/zeta/linux-devel/mtd-bench/mnt
Notice IUsed is negative. Also, 10% usage on a fresh f2fs seems too
much to be correct.
Reported-and-Tested-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We should guarantee not to do *scheduling while atomic*.
I found, in atomic f2fs_end_io_write(), there is a set_page_dirty() call
to deal with IO errors.
But, set_page_dirty() calls:
-> f2fs_set_data_page_dirty()
-> set_dirty_dir_page()
-> cond_resched() which results in scheduling.
In order to avoid this, I'd like to remove simply set_page_dirty(),
since the page is already marked as ERROR and f2fs will be operated
as the read-only mode as well.
So, there is no recovery issue with this.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, f2fs didn't track the parent inode number correctly which is stored
in each f2fs_inode. In the case of the following scenario, a bug can be occured.
Let's suppose there are one directory, "/b", and two files, "/a" and "/b/a".
- pino of "/a" is ROOT_INO.
- pino of "/b/a" is DIR_B_INO.
Then,
# sync
: The inode pages of "/a" and "/b/a" contain the parent inode numbers as
ROOT_INO and DIR_B_INO respectively.
# mv /a /b/a
: The parent inode number of "/a" should be changed to DIR_B_INO, but f2fs
didn't do that. Ref. f2fs_set_link().
In order to fix this clearly, I added i_pino in f2fs_inode_info, and whenever
it needs to be changed like in f2fs_add_link() and f2fs_set_link(), it is
updated temporarily in f2fs_inode_info.
And later, f2fs_write_inode() stores the latest information to the inode pages.
For power-off-recovery, f2fs_sync_file() triggers simply f2fs_write_inode().
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Do cleanup more for better code readability.
- Change the parameter set of f2fs_bio_alloc()
This function should allocate a bio only since it is not something like
f2fs_bio_init(). Instead, the caller should initialize the allocated bio.
- Introduce SECTOR_FROM_BLOCK
This macro translates a block address to its sector address.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Reviewed-by: Namjae Jeon <namjae.jeon@samsung.com>
Simplify code by providing the accessor macro to retrieve the
number of dentry slots for a given filename length.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Since, we anyway need to put the page after deleting entry. So, there is no
need to make same call under different conditions.
Move out the f2fs_put_page from the two conditions and call at once.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Since, GFP_NOFS and __GFP_ZERO is being used to set gfp_mask.
We can instead make use of already predefined macro GFP_F2FS_ZERO.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Since, GFP_NOFS(__GFP_WAIT) is used for allocation requests of bio in f2fs.
So, there is no chance of returning NULL from the BIO allocation.
Making the bio allocation routine for f2fs simpler.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
The variables node_page and page_offset are initialized but never used
otherwise, so remove those unused variables.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
In function f2fs_mkdir, err is being initialized without even checking
if there was any error in new inode creation. So, instead check the
inode error and make use of error/return condition.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
No need to initialize "struct f2fs_gc_kthread *gc_th = NULL",
as gc_th = NULL, will be taken care by the return values of kmalloc().
And fix codes in other places.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
If the filesystem is mounted as read-only then return from that point itself
instead of first doing a writeout/wait and then checking for read-only
condition.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Since, __GFP_ZERO is used while f2fs inode allocation, so we do not
need memset for f2fs_inode_info, as this is already zeroed out.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
print the invalid argument/value from parse_options in case of
mount failure.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
When CONFIG_CC_OPTIMIZE_FOR_SIZE is enabled in the kernel, -Os optimisation
flag is passed to gcc for compilation, and somehow while trying to optimize
the code, compiler is might not able to see the initialisation of variable
ne struct variable inside the get_node_info() function and results into
following warning:
fs/f2fs/node.c: In function 'get_node_info':
fs/f2fs/node.c:175:3: warning: 'ne.block_addr' may be used uninitialized in
this function [-Wuninitialized]
fs/f2fs/node.c:265:24: note: 'ne.block_addr' was declared here
fs/f2fs/node.c:176:3: warning: 'ne.ino' may be used uninitialized in this
function [-Wuninitialized]
fs/f2fs/node.c:265:24: note: 'ne.ino' was declared here
fs/f2fs/node.c:177:3: warning: 'ne.version' may be used uninitialized in
this function [-Wuninitialized]
fs/f2fs/node.c:265:24: note: 'ne.version' was declared here
Hence, lets initialise the ne struct variable to zero, which will remove
this warning and also doing this does not seems to making any impact on the
code behavior.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
There exist two build failures reported by Randy Dunlap as follows.
(on i386)
a. (config-r8857)
ERROR: "f2fs_xattr_advise_handler" [fs/f2fs/f2fs.ko] undefined!
Key configs in (config-r8857) are as follows.
CONFIG_F2FS_FS=m
# CONFIG_F2FS_STAT_FS is not set
CONFIG_F2FS_FS_XATTR=y
# CONFIG_F2FS_FS_POSIX_ACL is not set
The error was occurred due to the function location that we made a mistake.
Recently we added a new functionality for users to indicate cold files
explicitly through xattr operations (i.e., f2fs_xattr_advise_handler).
This handler should have been added in xattr.c instead of acl.c in order
to avoid an undefined operation like in this case where XATTR is set and
ACL is not set.
b. (config-r8855)
fs/f2fs/file.c: In function 'f2fs_vm_page_mkwrite':
fs/f2fs/file.c:97:2: error: implicit declaration of function
'block_page_mkwrite_return'
Key config in (config-r8855) is CONFIG_BLOCK.
Obviously, f2fs works on top of the block device so that we should consider
carefully a sort of config dependencies.
The reason why this error was occurred was that f2fs_vm_page_mkwrite() calls
block_page_mkwrite_return() which is enalbed only if CONFIG_BLOCK is set.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
As pointed out by Randy Dunlap, this patch removes all usage of "/**" for comment
blocks. Instead, just use "/*".
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch should resolve the bugs reported by the sparse tool.
Initial reports were written by "kbuild test robot" managed by fengguang.wu.
In my local machines, I've tested also by running:
> make C=2 CF="-D__CHECK_ENDIAN__"
Accordingly, I've found lots of warnings and bugs related to the endian
conversion. And I've fixed all at this moment.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This adds Makefile and Kconfig for f2fs, and updates Makefile and Kconfig files
in the fs directory.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This moves all of the f2fs debugging files into debugfs. The files are
located in /sys/kernel/debug/f2fs/
Note, I think we are generating all of the same information in each of
the files for every unique f2fs filesystem in the machine. This copies
the functionality that was present in the proc files, but this should be
fixed up in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[jaegeuk.kim@samsung.com: merged 3 debugfs entries into a *status* entry]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This adds roll-forward routines to recover fsynced data.
- F2FS uses basically roll-back model with checkpointing.
- In order to implement fsync(), there are two approaches as follows.
1. A roll-back model with checkpointing at every fsync()
: This is a naive method, but suffers from very low performance.
2. A roll-forward model
: F2FS adopts this model where all the fsynced data should be recovered, which
were written after checkpointing was done. In order to figure out the data,
F2FS keeps a "fsync" mark in direct node blocks. In addition, F2FS remains
the location of next node block in each direct node block for reconstructing
the chain of node blocks during the recovery.
- In order to enhance the performance, F2FS keeps a "dentry" mark also in direct
node blocks. If this is set during the recovery, F2FS replays adding a dentry.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This adds on-demand and background cleaning functions.
- The basic background cleaning policy is trying to do cleaning jobs as much as
possible whenever the system is idle. Once the background cleaning is done,
the cleaner sleeps an amount of time not to interfere with VFS calls. The time
is dynamically adjusted according to the status of whole segments, which is
decreased when the following conditions are satisfied.
. GC is not conducted currently, and
. IO subsystem is idle by checking the number of requets in bdev's request
list, and
. There are enough dirty segments.
Otherwise, the time is increased incrementally until to the maximum time.
Note that, min and max times are 10 secs and 30 secs by default.
- F2FS adopts a default victim selection policy where background cleaning uses
a cost-benefit algorithm, while on-demand cleaning uses a greedy algorithm.
- The method of moving data during the cleaning is slightly different between
background and on-demand cleaning schemes. In the case of background cleaning,
F2FS loads the data, and marks them as dirty. Then, F2FS expects that the data
will be moved by flusher or VM. In the case of on-demand cleaning, F2FS should
move the data right away.
- In order to identify valid blocks in a victim segment, F2FS scans the bitmap
of the segment managed as an SIT entry.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This implements xattr and acl functionalities.
- F2FS uses a node page to contain use extended attributes.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This adds inode operations for directory, symlink, and special inodes.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This adds core functions to get, read, write, and evict an inode.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This adds address space operations for data.
- F2FS supports readpages(), writepages(), and direct_IO().
- Because of out-of-place writes, f2fs_direct_IO() does not write data in place.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This adds memory operations and file/file_inode operations.
- F2FS supports fallocate(), mmap(), fsync(), and basic ioctl().
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This adds specific functions not only to manage dirty/free segments, SIT pages,
a cache for SIT entries, and summary entries, but also to allocate free blocks
and write three types of pages: data, node, and meta.
- F2FS maintains three types of bitmaps in memory, which indicate free, prefree,
and dirty segments respectively.
- The key information of an SIT entry consists of a segment number, the number
of valid blocks in the segment, a bitmap to identify there-in valid or invalid
blocks.
- An SIT page is composed of a certain range of SIT entries, which is maintained
by the address space of meta_inode.
- To cache SIT entries, a simple array is used. The index for the array is the
segment number.
- A summary entry for data contains the parent node information. A summary entry
for node contains its node offset from the inode.
- F2FS manages information about six active logs and those summary entries in
memory. Whenever one of them is changed, its summary entries are flushed to
its SIT page maintained by the address space of meta_inode.
- This patch adds a default block allocation function which supports heap-based
allocation policy.
- This patch adds core functions to write data, node, and meta pages. Since LFS
basically produces a series of sequential writes, F2FS merges sequential bios
with a single one as much as possible to reduce the IO scheduling overhead.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This adds specific functions to manage NAT pages, a cache for NAT entries, free
nids, direct/indirect node blocks for indexing data, and address space for node
pages.
- The key information of an NAT entry consists of a node id and a block address.
- An NAT page is composed of block addresses covered by a certain range of NAT
entries, which is maintained by the address space of meta_inode.
- A radix tree structure is used to cache NAT entries. The index for the tree
is a node id.
- When there is no free nid, F2FS should scan NAT entries to find new one. In
order to avoid scanning frequently, F2FS manages a list containing a number of
free nids in memory. Only when free nids in the list are exhausted, scanning
process, build_free_nids(), is triggered.
- F2FS has direct and indirect node blocks for indexing data. This patch adds
fuctions related to the node block management such as getting, allocating, and
truncating node blocks to index data.
- In order to cache node blocks in memory, F2FS has a node_inode with an address
space for node pages. This patch also adds the address space operations for
node_inode.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This adds functions required by the checkpoint operations.
Basically, f2fs adopts a roll-back model with checkpoint blocks written in the
CP area. The checkpoint procedure includes as follows.
- write_checkpoint()
1. block_operations() freezes VFS calls.
2. submit cached bios.
3. flush_nat_entries() writes NAT pages updated by dirty NAT entries.
4. flush_sit_entries() writes SIT pages updated by dirty SIT entries.
5. do_checkpoint() writes,
- checkpoint block (#0)
- orphan inode blocks
- summary blocks made by active logs
- checkpoint block (copy of #0)
6. unblock_opeations()
In order to provide an address space for meta pages, f2fs_sb_info has a special
inode, namely meta_inode. This patch also adds the address space operations for
meta_inode.
Signed-off-by: Chul Lee <chur.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This adds the implementation of superblock operations for f2fs, which includes
- init_f2fs_fs/exit_f2fs_fs
- f2fs_mount
- super_operations of f2fs
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This adds the following major in-memory structures in f2fs.
- f2fs_sb_info:
contains f2fs-specific information, two special inode pointers for node and
meta address spaces, and orphan inode management.
- f2fs_inode_info:
contains vfs_inode and other fs-specific information.
- f2fs_nm_info:
contains node manager information such as NAT entry cache, free nid list,
and NAT page management.
- f2fs_node_info:
represents a node as node id, inode number, block address, and its version.
- f2fs_sm_info:
contains segment manager information such as SIT entry cache, free segment
map, current active logs, dirty segment management, and segment utilization.
The specific structures are sit_info, free_segmap_info, dirty_seglist_info,
curseg_info.
In addition, add F2FS_SUPER_MAGIC in magic.h.
Signed-off-by: Chul Lee <chur.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
