This slipped in through the merging of different trees. Remove
__devexit_p() use in the mxc_w1 driver.
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These devices are not available on other architectures, so
let's limit them to omap.
If the driver subsystem maintainers want to build test
system wide changes without building for each target,
it's easy to carry a test patch that just strips out the
depends entries from Kconfig files.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's no reason to have the OF defines; it complicates the driver.
There's also no need for the funky platform_driver_probe.
Add a few warnings in case there's a failure; helps us find out
what went wrong.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are dealing with mxc_w1 registers.
While at it use dev_err() instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using module_platform_driver() makes the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the new i.mx clock framework the mxc_w1 clock is registered as:
clk_register_clkdev(clk[owire_gate], NULL, "mxc_w1.0");
So we do not need to pass "owire" string and can use NULL instead.
While at it, also fix the clock error handling code.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
-----
Changes since v2:
- Add Ack's
Changes since v1:
- Fix clock error handling
drivers/w1/masters/mxc_w1.c | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Paul Walmsley <paul@pwsan.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" char/misc driver tree update for the 3.7-rc1 merge
window.
Nothing major, just a number of driver updates and fixes, all of which
have been in the linux-next releases for a while now either in my tree,
or in Andrew's (the lis3l driver changes came from his tree last week).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp3pcACgkQMUfUDdst+ymLswCcDYG9RkRcEdYwT5bOm1zM4IVl
WM0AoLKfC86g6xe4MdS7zROJn7ep/9qu
=zAHk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver merge from Greg Kroah-Hartman:
"Here is the "big" char/misc driver tree update for the 3.7-rc1 merge
window.
Nothing major, just a number of driver updates and fixes, all of which
have been in the linux-next releases for a while now either in my
tree, or in Andrew's (the lis3l driver changes came from his tree last
week).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (52 commits)
drivers/misc/lis3lv02d/lis3lv02d_i2c.c: add lis3lv02d device tree init
drivers/misc/lis3lv02d/lis3lv02d_spi.c: add lis3lv02d device tree init
drivers/misc/lis3lv02d: remove lis3lv02d driver DT init
drivers/misc/lis3lv02d/lis3lv02d_spi.c: add DT matching table passthru code
drivers/misc/lis3lv02d: add generic DT matching code
lis3lv02d: fix some comments specific to lis331dlh driver
MISC: hpilo, remove pci_disable_device
pcmcia: synclink_cs: fix potential tty NULL dereference
drivers/char/mmtimer.c: Remove useless kfree
drivers/char: removes unnecessary semicolon
char/misc: remove CONFIG_EXPERIMENTAL dependencies
mei: don't print buffer as a string
mei: struct mei_message_data doesn't have to be packed
mei: add error messages for open count errors
misc: use module_spi_driver
tifm: use module_pci_driver
misc/at25, dt: Improve at25 SPI eeprom device tree bindings.
mei: add lynx point pci device ids
mei: fix max number of open handles
mei: rename struct pci_dev *mei_device to mei_pdev
...
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
This patch adds support for maxim ds1825 based 1-wire temperature sensors.
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the process of porting boards to devicetree implemenation, we should
keep information about external circuitry where they belong - the
individual drivers.
This patch adds a way to specify a GPIO to drive the (optional) external
pull-up logic, rather than using a function pointer for that.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add DT bindings to the w1-gpio driver, along with some
documentation on how to use them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let the driver compile everywhere while
also removing unnecessary headers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this lets us remove a bit of boilerplate code.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
we have the helpful resource_size() macro to
calculate the size of the memory resource for
us, let's use it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big driver core pull request for 3.6-rc1.
Unlike 3.5, this kernel should be a lot tamer, with the printk changes now
settled down. All we have here is some extcon driver updates, w1 driver
updates, a few printk cleanups that weren't needed for 3.5, but are good to
have now, and some other minor fixes/changes in the driver core.
All of these have been in the linux-next releases for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlARgIUACgkQMUfUDdst+ynDHgCfRNwIB9L+zZvjcKE5e1BhDbUl
wVUAn398DFgbJ1+PjGkd1EMR2uVTh7Ou
=MIFu
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg Kroah-Hartman:
"Here's the big driver core pull request for 3.6-rc1.
Unlike 3.5, this kernel should be a lot tamer, with the printk changes
now settled down. All we have here is some extcon driver updates, w1
driver updates, a few printk cleanups that weren't needed for 3.5, but
are good to have now, and some other minor fixes/changes in the driver
core.
All of these have been in the linux-next releases for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (38 commits)
printk: Export struct log size and member offsets through vmcoreinfo
Drivers: hv: Change the hex constant to a decimal constant
driver core: don't trigger uevent after failure
extcon: MAX77693: Add extcon-max77693 driver to support Maxim MAX77693 MUIC device
sysfs: fail dentry revalidation after namespace change fix
sysfs: fail dentry revalidation after namespace change
extcon: spelling of detach in function doc
extcon: arizona: Stop microphone detection if we give up on it
extcon: arizona: Update cable reporting calls and split headset
PM / Runtime: Do not increment device usage counts before probing
kmsg - do not flush partial lines when the console is busy
kmsg - export "continuation record" flag to /dev/kmsg
kmsg - avoid warning for CONFIG_PRINTK=n compilations
kmsg - properly print over-long continuation lines
driver-core: Use kobj_to_dev instead of re-implementing it
driver-core: Move kobj_to_dev from genhd.h to device.h
driver core: Move deferred devices to the end of dpm_list before probing
driver core: move uevent call to driver_register
driver core: fix shutdown races with probe/remove(v3)
Extcon: Arizona: Add driver for Wolfson Arizona class devices
...
Convert the OMAP HDQ driver to use runtime PM. Compile- and boot-tested,
but not tested in actual use.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Tested-by: NeilBrown <neilb@suse.de>
HDQ/1-wire registers are 32 bits long, even if the register contents
fit into 8 bits, so accesses must be 32-bit aligned. Evidently the
OMAP2/3 interconnects allowed the driver to get away with 8 bit accesses,
but the OMAP4 puts a stop to that:
[ 1.488800] Driver for 1-wire Dallas network protocol.
[ 1.495025] Bad mode in data abort handler detected
[ 1.500122] Internal error: Oops - bad mode: 0 [#1] SMP
[ 1.505615] Modules linked in:
[ 1.508819] CPU: 0 Not tainted (3.3.0-rc1-00008-g45030e9 #992)
[ 1.515289] PC is at 0xffff0018
[ 1.518615] LR is at omap_hdq_probe+0xd4/0x2cc
The OMAP4430 ES2 Rev X TRM does warn about this restriction in section
23.2.6.2 "HDQ/1-Wire Registers".
Fixes the crash on OMAP4430 ES2 Pandaboard. Tested also on OMAP34xx and
OMAP2420; it seems to work fine on those chips, although due to the lack
of boards with HDQ/1-wire devices here, a more indepth test was not
possible.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Allow the OMAP HDQ1W driver to be built for all OMAP2+ SoCs by
adjusting KConfig dependencies. The previous dependency required
either SOC_OMAP2430 or ARCH_OMAP3 to be set, but the HDQ IP block is
present on OMAP2420 and OMAP44xx SoCs. The driver was still
selectable on multi-OMAP kernel configurations, however; so the
previous prohibition was rather pointless.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
The 'mutex' in struct w1_master is use for two very different
purposes.
Firstly it protects various data structures such as the list of all
slaves.
Secondly it protects the w1 buss against concurrent accesses.
This can lead to deadlocks when the ->probe code called while adding a
slave needs to talk on the bus, as is the case for power_supply
devices.
ds2780 and ds2781 drivers contain a work around to track which
process hold the lock simply to avoid this deadlock. bq27000 doesn't
have that work around and so deadlocks.
There are other possible deadlocks involving sysfs.
When removing a device the sysfs s_active lock is held, so the lock
that protects the slave list must take precedence over s_active.
However when access power_supply attributes via sysfs, the s_active
lock must take precedence over the lock that protects accesses to
the bus.
So to avoid deadlocks between w1 slaves and sysfs, these must be
two separate locks. Making them separate means that the work around
in ds2780 and ds2781 can be removed.
So this patch:
- adds a new mutex: "bus_mutex" which serialises access to the bus.
- takes in mutex in w1_search and ds1wm_search while they access
the bus for searching. The mutex is dropped before calling the
callback which adds the slave.
- changes all slaves to use bus_mutex instead of mutex to
protect access to the bus
- removes w1_ds2790_io_nolock and w1_ds2781_io_nolock, and the
related code from drivers/power/ds278[01]_battery.c which
calls them.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no gain in having a loop - there is no risk of missing the
interrupt with wait_event_timeout.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- some debug messages missed spaces
- sometimes no error was returned when it should have been
- sometimes a message is printed when there is no error, rather
than when there is one.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 59d4467be4.
Turns out it was the wrong version, will apply the correct version after
this.
Reported-by: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were some return statements around in the w1_uevent, used goto
to cleanup those return statements with the help of err variable,
and also removed a semi colon at the end of the w1_uevent's closing
brace.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1 devices need a mutex to serial IO. Most use master->mutex.
However that is used for other purposes and they can conflict.
In particular master->mutex is held while w1_attach_slave_device is
called.
For bq27000, this registers a 'powersupply' device which tries to read the
current status. The attempt to read will cause a deadlock on
master->mutex.
So create a new per-slave mutex and use that for serializing IO for
bq27000.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
There are three Kconfig entries with "--- help ---" attributes, and over
2000 Kconfig entries with "---help---" attributes. Apparently the three
attributes with embedded spaces are valid. Still, I see little reason
for using this obscure variant. And replacing those three attributes
with the common variant makes grepping Kconfig files for help texts a
bit easier too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
NULL not 0 should be used with pointers. Just remove the offending
lines since they will default to NULL anyway.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f19420c1ac.
It contained lots of errors and warnings and shouldn't have ever been
applied, that was my fault, sorry.
Cc: Markus Franke <markus.franke@s2002.tu-chemnitz.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>,
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should unlock here before returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch offers the possibility to disables irqs during w1_write_bit()
and w1_reset_bus() operations as timing requirements are very strict for
the 1-wire bus protocol. Per default interrupts are enabled but can be
disabled via the module parameter "w1_disable_irqs".
Extend 1-wire reset pulse length from 480us to 500us as 480us is the
minimum requirement for the 1-wire reset/presence pulse.
Signed-off-by: Markus Franke <franm@hrz.tu-chemnitz.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a 1-wire slave device driver for the DS28E04-100.
Signed-off-by: Markus Franke <franm@hrz.tu-chemnitz.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge with latest Linus' tree, as I have incoming patches
that fix code that is newer than current HEAD of for-next.
Conflicts:
drivers/net/ethernet/realtek/r8169.c
