GPHY revision G0 has its version rolled over to 0x10, introduce an
explicit check for that revision and invoke the proper workaround
function for it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY revisions E0 and F0 share the same shorter workaround initialization
sequence. Dedicate a special function for these two PHY revisions to
perform the needed workaround sequence.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY revision D0 requires a specific workaround sequence which needs to
be applied to get the HW to behave properly in all corner cases
conditions. Do this based on the revision we just read out of the HW
using a specific function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function performs a R/RC calibration reset and will start being
used by more than one function in the next patches, create a helper
function to factor code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm7445_config_init() was working around non-production version of the
PHY HW block, so just remove it entirely.
bcm7xxx_28nm_afe_config_init() was running for all PHY revisions greater
than B0, but this workaround sequence is really specific to the B0 PHY
revision, so rename the function accordingly and update the GPHY macro
to use the generic config_init callback.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm7xxx_28nm_config_init() can be called as frequently as needed by the
PHY library upon suspend/resume cycles and interface bring up/down, just
print the PHY revision once and for all in order not to spam kernel
logs.
Fixes: d8ebfed3f1 ("net: phy: bcm7xxx: utilize PHY revision in config_init")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace module init/exit which only calls phy_drivers_register with
module_phy_driver macro.
Tested using Micrel driver, and otherwise compile-tested only.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the GENET and SF2 drivers have been updated to communicate us
what is the revision of the BCM7xxx integrated PHY, utilize that
information in the config_init() callback to call into the appropriate
workaround function based on our revision.
While at it, we also print the revision and patch level to help debug
new chips.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for the PHY driver to check PHY_BRCM_100MBPS_WAR since
that is redundant with checking the PHY device supported features. Get
rid of that workaround flag.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new entries to the Broadcom BCM7xxx internal PHY driver for
BCM7250 and BCM7364 chips. Those chips share the usual 28nm process
Gigabit PHY sequence and require the same workarounds so far.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 28nm Gigabit PHYs supported by the driver have the same
callbacks, the only differences being the 32-bits OUI and the name. Use
a macro to factor this, making it easier in the future to add new
entries.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 28nm Gigabit PHY on BCM7xxx chips comes out of reset with absolutely
no EEE capabilities, such that we would actually return that we do not
support EEE when accessing 3.20 (MDIO_PCS_EEE_ABLE) registers.
Poke through the vendor-specific C45 register to enable EEE globally at
the PHY level, and advertise supported EEE modes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 28nm process BCM7xxx internal Gigabit PHYs all support automatic
power down, turn on that feature as part of the configuration
initialization callback.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM7xxx internal Gigabit PHY on 28nm process do not need anything
special to be done during suspend, remove the suspend callback since it
might be harmful rather than useful. While at it, update the comment
above bcm7xxx_suspend() to reflect that it applies only to 40nm and 65nm
process PHY devices.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
The BCM7xxx internal Gigabit PHYs on 28nm process platforms come out
reset without any half-duplex or "hub" compatible advertised modes,
which was causing auto-negotiation issues coming out of S3
suspend/resume, we just could not establish a link with a half-duplex
only link partner.
Make sure that the resume function properly re-configures the PHY device
to advertise all supported modes.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
A wildcard entry with the 32-bits OUI 0x600d8400 was added as part of
the BCM7xxx internal PHY driver, but that entry might match other PHYs
that are not covered by this driver, so let's just remove it.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
The AFE_RX_LP_COUNTER kept the last 3 bits set, which would not properly
clear the EEE LPI mode errors bits. Make sure that those bits are set to
0 to ensure the PHY timing is always good even during EEE wake-up.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Writing first to the AFE registers, and then the VCO, RCAL, RC_CAL
registers turned out to unveil some spurious MDIO read/write failures
which would make the workaround partially applied. The fix is to write
first to the VCO, RCAL, RC_CAL registers, and then write to the AFE
registers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define constants for the various registers used in
bcm7xxx_28nm_afe_config_init() to help clarify what this workaround is
about.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Broadcom BCM7xxx Set Top Box SoCs
internal PHYs. This driver supports the following generation of SoCs:
- BCM7366, BCM7439, BCM7445 (28nm process)
- all 40nm and 65nm (older MIPS-based SoCs)
The PHYs on these SoCs require a bunch of workarounds to operate
correctly, both during configuration time and at suspend/resume time,
the driver handles that for us.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
