The code unconditionlly increments the pio wait counter
making the counter inacurate and unusable.
Fixes: 14553ca110 ("staging/rdma/hfi1: Adaptive PIO for short messages")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The RESET_N bit of the ASIC_QSFPn_OE register is not used by
the hardware. Remove code that tries to use it - it does
nothing.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The external device configuration was incorrectly shifted to byte 3 of
the 32 bit DC_HOST_COMM_SETTINGS instead of byte 0. This patch corrects
the shift and provides the cable capability information in byte 0.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The function level reset in init_chip() and subsequent write of all 1s
to the ASIC_QSFP registers effectively resets attached active and
optical QSFP modules that pay attention to the RESET_N pin.
We subsequently try to access the QSFP management interface to qualify
and tune the channel and fabric SerDes before enough time (2 seconds
per SFF 8679 spec for QSFP28 modules) has elapsed for the module to
finish initialization. This fails and causes the failure of the channel
tuning algorithm, preventing us from bringing the link up.
This patch checks the port type prior to beginning channel and SerDes
tuning, and if found to be QSFP, watches for the QSFP initialization
complete interrupt, with a maximum timeout of 2 seconds, to allow the
initialization to complete.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
QSFP modules can raise an interrupt to inform us of expected conditions
while the link is down, such as RX power low. Actively ignore these
conditions when the link is down as they only add reporting noise.
Continue reporting conditions that are valid at all times, such as
temperature alarms and warnings.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Adding the needed mlx5_ifc hardware bits and structs
for the following features:
* Add vport to steering commands for SRIOV ACL support
* Add mlcr, pcmr and mcia registers for dump module EEPROM
* Add support for FCS, beacon led and disable_link bits to
hca caps
* Add CQE period mode bit in CQ context for CQE based CQ
moderation support
* Add umr SQ bit for fragmented memory registration
* Add needed bits and caps for Striding RQ support
In-order to avoid possible future conflicts between rdma and
net-next we added all expected updates to this file for this release.
If more changes will be submitted, we plan to do it only through
one of the subsystems, probably net-next.
All updated bits in this patch will be later used in
the up-coming submissions to net-next and rdma trees.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
All reserved fields after early_vf_enable are off by 1, since
early_vf_enable was not explicitly declared as array of size 1.
Reserved field before cqe_zip had a wrong size, it should
be 0x80 + 0x3f.
Fixes: b084444459 ("net/mlx5_core: Introduce access function to read internal timer ")
Fixes: b4ff3a36d3 ("net/mlx5: Use offset based reserved field names in the IFC header file")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Since all srp_map_finish_fr() callers pass a non-zero value as
the fourth argument (sg_nents), the sg_nents == 0 check in that
function can be removed. Add a count == 0 check in the caller
of that function.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The srp_queuecommand() function translates ENOMEM into QUEUE_FULL
which causes the SCSI mid-layer to retry the command. All other
error codes are translated into DID_ERROR which causes the SCSI
command to fail. Return E2BIG if mapping will always fail to
prevent that the SCSI mid-layer keeps resubmitting a command
forever.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ensure that req->nmdesc is set correctly in srp_map_sg() if mapping
fails. Avoid that mapping failure causes a memory descriptor leak.
Report srp_map_sg() failure to the caller.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The free request list was removed through patch "IB/srp: Use block layer tags".
Hence update a comment that refers to that free request list.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use c4iw_ep_disconnect() instead. This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.
This is the last user of abort_connection(), so remove it too.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In c4iw_ep_disconnect(), if we fail to initiate a close operation, then
move the qp to ERROR to disassociate the ep from the qp. Failure to do
this will leak the ep resources.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead return whether the caller needs to disconnect. This is part of
getting rid of abort_connection() altogether so we properly clean up on
send_abort() failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use c4iw_ep_disconnect() instead. This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead, have the caller, rx_data() handle the close/abort like
it does for process_mpa_request(). This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In rx_data(), with the ep in FPDU_MODE, refcnt=2, if we get unexpected
streaming data, we call c4iw_modify_rc_qp() and move the qp from
RTS -> TERMINATE. In c4iw_modify_rc_qp(), if rdma_fini() returns
an error, the ep will be dereferenced (refcnt=1). Then rx_data()
calls c4iw_ep_disconnect() which starts the close operation.
But if send_halfclose() fails in c4iw_ep_disconnect(), we will call
release_ep_resources() derefing the ep which reduces the refcnt to 0 and
and frees the ep. However we still has the ep mutex at that point, so we
have a touch-after-free bug. There is a similar issue where
peer_close() calls c4iw_ep_disconnect().
The solution is to add a reference to the ep in c4iw_ep_disconnect()
after acquiring the mutex, and release it after releasing the mutex.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In c4iw_ep_disconnect(), if we start the ep timer to begin a close,
but send_halfclose() fails, we need to stop the timer and send a CLOSE
event up to the IWCM before releasing the resources. Otherwise, we can
crash when the ep timer fires if the ep is referencing a previous instance
of the device. This can happen as part of adapter reset/recovery, for
instance.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If ARP fails before the CPL_PASS_ACCEPT_RPL is seen by hardware, the tid
will be stuck in SYN_PEND and never released. So create an arp failure
handler specifically for this message to release the endpoint resources.
In pass_accept_rpl_arp_failure(), put the parent endpoint so it will
be freed when destroyed. Also we don't need to call release_tid() here
because _c4iw_free_ep() calls cxgb4_remove_tid() which releases the
hwtid.
If we get an ABORT_REQ_RSS instead of a PASS_ESTABLISH (because the
peer's ACK to our SYN is never received), then put the parent as well
in peer_abort().
Treat accept_cr() failures just like arp failures: put the parent ep
and release the ep resources destroying the tid
The ARP failure handlers are called in an atomic context, so we need to
schedule some of the processing which might block. Namely _c4iw_free_ep()
which needs a mutex. So create a "special" CPL opcode and handler and
schedule it via sched() to be run by process_work() in a blockable context.
Also rework the active open arp failure handler to make use of
release_ep_resources(). This allows both the active and passive arp
failure handlers to use the same deferred cleanup function.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
iSER currently has a couple places that set max_sectors in either the host
template or SCSI host, and all of them get it wrong.
This patch instead uses a single assignment that (hopefully) gets it right:
the max_sectors value must be derived from the number of segments in the
FR or FMR structure, but actually be one lower than the page size multiplied
by the number of sectors, as it has to handle the case of non-aligned I/O.
Without this I get trivial to reproduce hangs when running xfstests
(on XFS) over iSER to Linux targets.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Alternatively one could free the skb, OTOH I don't think this test is
useful so just remove it.
Cc: <linux-rdma@vger.kernel.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix for removing a quad hash entry when the
corresponding quad hash entry hasn't been added,
which is the case in loopback connections
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix for checking if the QP associated with a completion
has been destroyed while processing CQ elements.
If that is the case, move the CQ head to the next element
and continue completion processing.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A check is added to validate the requested sge number.
iWARP doesn't support multiple sg elements for
RDMA READ work requests.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix to calculate the SQ size based on the max
frag_count, requested by the application instead
of overwriting it with the max supported frag_count
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
STag index mask is calculated incorrectly, missing
the 14 bits minimum requirement. Add max macro to use
either # of MRs or 14 bits in the mask size calculation.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Invalidation after every WQE write is changed to invalidate
only if required. NOPs are padded so that WQE writes are
aligned to 64B boundary.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Adding sq and rq drain functions, which block until all
previously posted wr-s in the specified queue have completed.
A completion object is signaled to unblock the thread,
when the last cqe for the corresponding queue is processed.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Correct SD calculation by using base address returned from commit FPM.
This alleviates any assumptions on resource ordering and alignment
requirement. Also consolidate SD estimation code into i40iw_est_sd().
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix endian warnings and errors due to u32 stored to u16.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Implement fast register mr, Local invalidate, send with
invalidate and RDMA read with invalidate.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Initialize max enabled vfs to max rdma vfs instead of 0.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Move return code check to immediately after i40iw_hmc_sd_one call
where it is set instead of outside the then statement.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Queue users of virtual channel on a waitqueue until the channel is
clear instead of failing the call when the channel is occupied.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add a check for cq_poll_info.error before setting vendor_err
instead of always setting it.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
QP may be freed during Async Event processing.
Add a lock around QP table to prevent it.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
iwqp->allocated_buffer is a self-referencing pointer to iwqp.
Do not set iwqp->allocated_buffer to NULL after freeing it.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Make sure cm_node is setup before sending SYN packet and
ORD/IRD negotiation.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Include inline data size as part of SQ size calculation.
RQ size calculation uses only number of SGEs and does not
support 96 byte WQE size.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
