There is really no point to retry to add children devices in case the
of_platform_populate() fails.
We do not have any information provided via pdata in this case anyways.
Depending on the boot type (legacy or DT) only execute either one.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
At boot time we can allocate the twl_modules array dynamically based on the
twl class we are using with devm_kzalloc() instead of the static
twl_modules[] array.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Instead of using SUB_CHIP_ID* or magic numbers use the twl_mapping table to
look for the subchip ID.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The module id table no longer can have invalid/unused entries.
No need for checking the ID for validity.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use enums for all module definitions:
twl_module_ids for common functionality among twl4030/twl6030
twl4030_module_ids for twl4030 specific ids
twl6030_module_ids for twl6030 specific ids
In this way the list can be managed easier when new functionality going to
be implemented.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow the MICBIAS voltages and other attributes to be configured by the
platform.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the mixer is underclocked it will drop a sample so log that error
more directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Runtime power management does not function during system suspend but the
Arizona devices need to use runtime power management to power up the device
in order to handle interrupts. Try to avoid interrupts firing during
resume by disabling the primary IRQ before interrupts are reenabled on
resume and only reenabling it again during main resume.
The goal is to avoid issues in the situation where an interrupt is asserted
during resume (eg, due to it being the wake source) and the interrupt
handling gets scheduled prior to the device being able to handle runtime
PM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM5102 register defaults are not up to date with the current register
map, synchronise them with those for current devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We can cache some of them but this is simpler for now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
devm_regulator_bulk_get is device managed and saves some cleanup
and exit code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The latest evaluation of the revision B silicon suggests some changes to
the tuning applied for optimal performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Not strictly required as probe deferral will take care of everything but
it makes boot a little smoother.
Reported-by: Ryo Tsutsui <Ryo.Tsutsui@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since regmap sometimes uses volatile as a proxy for readable simply
having a blanket condition can mark too many registers as readable.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Palma RTC is capable of generating alarm interrupt. Pass the alarm interrupt
as IRQ_RESOURCE for palmas-rtc sub device driver so that rtc driver can get
irq as platform_get_irq().
Also pass the irq domain in mfd_add_devices() to properly offset the irqs for
sub devices. This is needed when adding device through DT.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixes the below build warning when driver is built-in.
drivers/mfd/omap-usb-host.c:750:12: warning:
‘usbhs_omap_remove’ defined but not used [-Wunused-function]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
clk_set_parent is expected to fail on OMAP3 platforms. We don't
consider that as fatal so don't spam console.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We split initializing revision 1 and revision 2 into different
functions. Initialization is now done dynamically so that only
the number of ports available on the system are initialized.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
The driver does not have an interrupt handler and
we don't really need a spinlock, so get rid of it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Enable the optional HSIC clocks (60MHz and 480MHz) for the ports
that are configured in HSIC mode.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
All ports have similarly named port clocks so we can
bunch them into a port data structure and use for loop
to enable/disable the clocks.
Dynamically allocate and get clocks based on number of ports
available on the platform
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Both OMAP4 and 5 exhibit the same revision ID in the REVISION register
but they have different number of ports i.e. 2 and 3 respectively.
So we can't rely on REVISION register for number of ports on OMAP5
and depend on platform data (or device tree) instead.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Use devm_ variants of kzalloc and ioremap. Also clean up error path.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Get rid of the unnecessary missing platform data checks
in runtime_suspend/resume. We are already checking for missing
platform data in probe.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
The TLL module on OMAP5 has 3 channels.
HSIC mode requires the TLL channel to be in Transparent UTMI mode.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Get rid of the unnecessary spin_lock_irqsave/restore() as there is
no interrupt handler for this driver. Instead we serialize access
to tll_dev using a global spinlock.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
omap_enable/disable_tll() can fail if TLL device is not
initialized. It could be due to multiple reasons and not only
due to missing platform data.
Also make local variables static and use 'struct device *'
instead of 'struct platform_device *' for global reference.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
No need to check for missing platform data in runtime_suspend/resume
as it makes more sense to do it in the probe function.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
This is a handy macro to check if the port requires the
USB TLL module or not. Use it to Enable the TLL module and manage
the clocks.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Every channel has a functional clock that is similarly named.
It makes sense to use a for loop to manage these clocks as OMAPs
can come with up to 3 channels.
Dynamically allocate and get channel clocks depending on the
number of clocks avaiable on the platform.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use devm_ variants of kzalloc() and ioremap(). Simplify the error path.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Fix channel count detecion for REV2. Also, don't give up
if we don't recognize the IP Revision. We assume the default
number of channels (i.e. 3) for unrecognized IPs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Let's have a single platform data structure for the OMAP's High-Speed
USB host subsystem instead of having 3 separate ones i.e. one for
board data, one for USB Host (UHH) module and one for USB-TLL module.
This makes the code much simpler and avoids creating multiple copies of
platform data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
For the ehci-omap.c part:
Acked-by: Alan Stern <stern@rowland.harvard.edu>
This is a branch of fixes that originally were scheduled for 3.8 but
due to the request from Linus to hold back on all but the most critical
of fixes, we're re-queueing them for 3.9 here.
* fixes-for-3.9:
ARM: dts: imx6: fix fec ptp clock slow 10 time
ARM: highbank: mask cluster id from cpu_logical_map
ARM: scu: mask cluster id from cpu_logical_map
ARM: scu: add empty scu_enable for !CONFIG_SMP
ARM: at91/at91sam9x5.dtsi: fix usart3 TXD
ARM: at91: at91sam9x5: fix usart3 pinctrl name
ARM: EXYNOS: Fix crash on soft reset on EXYNOS5440
ARM: dts: fix tick and alarm irq numbers for exynos5440
ARM: dts: fix compatible value for exynos pinctrl
ARM: dts: Fix compatible value of pinctrl module on EXYNOS5440
ARM: S3C24XX: fix uninitialized variable warning
mfd/vexpress: vexpress_sysreg_setup must not be __init
ARM: ux500: Fix u9540 booting issues
arm: mvebu: i2c come back in defconfig
arm: plat-orion: fix printing of "MPP config unavailable on this hardware"
Dove: activate GPIO interrupts in DT
ARM: ux500: add spin_unlock(&master_lock).
ARM: ux500: Disable Power Supply and Battery Management by default
Signed-off-by: Olof Johansson <olof@lixom.net>
When trying to get rid of the cross-includes of <mach/id.h>
from different drivers, so we can localize ASIC/CPU detection
to the mach-ux500 folder, we run into the way the PRCMU
handles base addresses and firmware detection.
This patch updates the firmware version detection to pass
the required information as platform data instead of
relying on cpu_is_* macros.
Now the PRCMU base address, the secondary TCDM area, the
TCPM area and the IRQ are passed as resources instead of
being grabbed from <mach/*> files. Incidentally this also
removes part of the reliance on <mach/irqs.h>.
Further it updates the firmware version detection, since the
location of the firmware ID bytes in the designated memory
are is now passed from the platform data instead. There is
no reason not to include the nice split-off of a struct to
hold the firmware information and a separate function to
populate it.
The patch actually rids the need to use the external
db8500_prcmu_early_init call at all, but I'm keepin back
that removal as I don't want the patch to be too big.
Cc: arm@kernel.org
Cc: Michel Jaoen <michel.jaouen@stericsson.com>
Cc: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Loic Pallardy <loic.pallardy@stericsson.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old AB8500 GPIO driver has been un-BROKEN and converted into a
multi-platform pinctrl driver. If any AB9540 based devices wish to
request any GPIO pins that it offers, they can after this patch.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old, BROKEN AB8500 GPIO driver has been revamped as a shiny
new pinctrl driver and has been renamed as such. So, if we would
like to make use of it, we need to register it via its new name.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the AB8500 IRQ mask and unmask functions, we rely on testing for
IRQ_TYPE_EDGE_RISING and IRQ_TYPE_EDGE_FALLING interrupts to
physically mask and unmask the correct interrupt lines. In order
for us to do that, the trigger needs to be set in the associated
flags. However, unless a irq_set_type() function pointer is passed
when registering the IRQ chip, the IRQ subsystem will refuse to do
it. For that reason, we're providing one.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch:
"mfd: ab8500: prepare to handle AB8500 GPIO's IRQs correctly"
altered the AB8500 IRQ mask/unmask functions such that they
would handle masking on/off the falling edge IRQ if this was
requested by the consumer. However the bit mask for hwirqs
43 and 44 was shifting the bit mask incorrectly, resulting in
the wrong IRQ being mased/unmasked.
Further while the patch would mask/unmask the correct line,
when the interrupt actually came in, it would still be treated
as a valid hwirq. The offsetting applied when masking/unmasking
was not applied when handling the IRQ, i.e. the falling edge
lines were not routed back to the rising edge lines.
This fixes both cases. The end result has been tested with
the SIM detect IRQ, GPIO12, hwirq 46 and 62.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
In an upcoming patch, the gpio-ab8500 driver will relinquish all
IRQ handling capability and pass it back into the AB8500 core
driver. This will aid in reducing massive code duplication within
the kernel. Also, most of the functionality is already in the
AB8500 core driver, as the GPIO IRQs are actually sandwiched
between lots of other IRQs which the core driver already handles.
All we're doing here is providing the core driver with knowledge
that each GPIO has two IRQs assigned to it; one for rising and
a separate one for falling.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix drift in DT parsing function name in the stub code.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This device tree support is added for PMIC block of S5m8767 multi
function driver. The usage detail is added in the device tree
documentation section. This change is tested on exynos5250 based
arndale platform by regulator voltage set/get API's.
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The new format of ab8500_gpadc_get() accepts a device name as a
parameter to specify which device to retrieve. This patch
enforces the use of that new format.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
The ab8500_gpadc structure carries lots of important information which
most functions make good use of. The initial expectation was that
ab8500_gpadc_runtime_idle() would be no exception; however, this hasn't
been the case to date. Let's remove it for now and add it back in only
when we have a use for it.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reduce the conversion timeout from 2s to 0.5s
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Simple pointer error fix to obtain the expected sizeof() result.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ashok G <ashok.g@stericsson.com>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Add runtime pm support to speed up multiple ADC reads in a row.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Ulf HANSSON <ulf.hansson@stericsson.com>
This patch adds an entry in debugfs to check number of interrupts
from the AB.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
Add support for AB8505 and AB9540
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@stericsson.com>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
With the introduction of new AB* platforms, it's important to allow
as much code reuse as possible. By allowing a system's number of IRQs
to be dynamically passed, we can reuse almost all of the -debugfs
driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Implement an API so that a user may dump all AB8500 registers
via debugfs file access.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Linus WALLEIJ <linus.walleij@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Update the ab8500_registers_print() to reuse it from multiple places.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Linus WALLEIJ <linus.walleij@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
In case of AB-V3, the eye diagram related issues are resolved.
So, set the device charging current to 300mA when connected to
standard host. Also, add the USB PHY tuning values to improve
the USB eye diagram
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: <thirupathi.chippakurthy@stericsson.com>
Allow a user to take a glimpse into the inner workings of the
AB8500 Analogue-to-Digital Converters, via debugfs.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: John Beckett <john.beckett@stericsson.com>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Add debugfs entry ab8500/hwreg to read/write bit-field in AB8500 registers.
Check the debugfs entries usage from heading comments in ab8500-debugfs.c
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: carriere etienne <etienne.carriere@stericsson.com>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Partly for coding style reasons, but mostly because sparse warns on it.
This patch is a completion of a previous patch by Mark Brown.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds a counter to the sysfs file dynamically created
by debugfs. It also fixes an array index error.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Reviewed-by: Mattias NILSSON <mattias.i.nilsson@stericsson.com>
Some drivers can detect subsystem failures e.g. shared memory driver
can detect modem sub system failures. It would be helpful in analyzing
these failures if AB register dump is available at that point. This
patch adds the API for the drivers to dump AB registers in the kernel
log.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Linus WALLEIJ <linus.walleij@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Export ab8500_sysctrl_read() and ab8500_sysctrl_write() symobols.
They will be used by LTP test cases.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
Add the possibility to pass configuration settings for
SysCl1kReqRfClkBuf to SysClk8ReqRfClkBuf via platform data.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kennet Wallden <kennet.wallden@stericsson.com>
Reviewed-by: Karl-Johan PERNTZ <karl-johan.perntz@stericsson.com>
Reviewed-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
The resolution of msleep is related to HZ, so with HZ set to
100 any msleep of less than 10ms will become ~10ms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It's possible to supply a string to provide a reason for
triggering a restart. In this case our reason is to enter
charging-only mode, as a charger was found to be present.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
When a charger is connected, we usually want AB8500 based systems to
reboot into charging-only mode. However, if the battery type cannot
be identified this would be futile, so we'll just shut the system
down instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
If a charger is attached on power off, reboot the system
into charging mode instead of powering it off.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
The kernel allows us to specify a function call-back which will be
invoked when a system power-off request has been received. Here we
provide one which is to be used when shutting down AB8500 based
platforms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
* Move sp810 header to a more generic location,
mainly to share it with arm64
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRCULAAAoJEL9jRaJfXa5PyysH/AsFbihoAGU0S7o+ggyN4S8m
5myEfbdMvgI5Hjcl/MgcVJAl6jFpDjmBH5ZPu+o8WzoP5L91C9F//kMRZqK0zATj
Y2OdMVNfVQG94bSsmjHryWF8W0RYcY2bQr0wJmgguNDpRLFsFdF3Rb58AWzG+2tP
KFxDg9u/CyhC/sv7BzoKI+J3ol5wEmv4BNMbPyjYG8L5TcBfe/IZqnl6KZ/QAw5i
QUFs3oXtT4/v8bnsxAym+VXIvjSHWs2t0CivfMyH+ZIgb3NbfJ1gIOCOJIk5XWTu
6L1yYyBBcRr60y9p4s2Nd4NxHZEB7pyZYuboUOxSmRNnEM54RT2Nkvcdon8j6Rw=
=uB7w
-----END PGP SIGNATURE-----
Merge tag 'vexpress/drivers-for-3.9' of git://git.linaro.org/people/pawelmoll/linux into next/drivers
From Pawel Moll:
Versatile Express related driver updates for 3.9:
* Move sp810 header to a more generic location,
mainly to share it with arm64
* tag 'vexpress/drivers-for-3.9' of git://git.linaro.org/people/pawelmoll/linux:
arm: Move sp810.h to include/linux/amba/
+ Linux 3.8-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
- First an ACKed MFD patch deleting the only consumer
of these cpu_is* functions outside of mach-ux500
- Introduce a new local cpu_is_u8580() in this patch
set to avoid clashing with other patch sets.
- Finally de-globalize <mach/id.h>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=zjvx
-----END PGP SIGNATURE-----
Merge tag 'ux500-no-idh' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/cleanup
From Linus Walleij:
Removal of the <mach/id.h> include from ux500
- First an ACKed MFD patch deleting the only consumer
of these cpu_is* functions outside of mach-ux500
- Introduce a new local cpu_is_u8580() in this patch
set to avoid clashing with other patch sets.
- Finally de-globalize <mach/id.h>.
* tag 'ux500-no-idh' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: de-globalize <mach/id.h>
ARM: ux500: Introduce cpu_is_u8580()
mfd: prcmu: delete pin control helpers
Signed-off-by: Olof Johansson <olof@lixom.net>
This removes the file <mach/id.h> from the global kernel include
scope, making it a pure mach-ux500 detail. All ASIC specifics
needed by drivers shall henceforth be passed from either platform
data or the device tree.
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch 52666298a 'mfd: vexpress-sysreg: Don't skip initialization
on probe' adds a call to vexpress_sysreg_setup from a non-__init
function, so this also has to lose its __init annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: arm@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
* depends/cleanup: (375 commits)
ARM: at91: fix board-rm9200-dt after sys_timer conversion
clocksource: use clockevents_config_and_register() where possible
ARM: use clockevents_config_and_register() where possible
clockevents: export clockevents_config_and_register for module use
timer: vt8500: Move timer code to drivers/clocksource
irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
ARM: picoxcell: use common irqchip_init function
ARM: spear: use common irqchip_init function
irqchip: Move ARM VIC to drivers/irqchip
ARM: samsung: remove unused tick.h
ARM: remove unneeded vic.h includes
ARM: remove mach .handle_irq for VIC users
ARM: VIC: set handle_arch_irq in VIC initialization
ARM: VIC: shrink down vic.h
irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
ARM: use common irqchip_init for GIC init
irqchip: Move ARM GIC to drivers/irqchip
ARM: remove mach .handle_irq for GIC users
ARM: GIC: set handle_arch_irq in GIC initialization
ARM: GIC: remove direct use of gic_raise_softirq
...
We have some build failure fixes (twl4030, vexpress, abx500 and tps65910),
some actual runtime oops and lockup fixes (rtsx, da9052), and some more
hypothetical NULL pointers dereferences fixes for pcf50633 and max776xx.
Then we also have additional rtsx fixes for a correct switch output voltage
and clock divider correctness for rtl8411 (rtsx driver), and irqdomain fix for
db8550-prcmu, and some more cosmetic fixes for arizona and wm5102.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=rxug
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"This is the first pull request for MFD fixes for 3.8
We have some build failure fixes (twl4030, vexpress, abx500 and
tps65910), some actual runtime oops and lockup fixes (rtsx, da9052),
and some more hypothetical NULL pointers dereferences fixes for
pcf50633 and max776xx.
Then we also have additional rtsx fixes for a correct switch output
voltage and clock divider correctness for rtl8411 (rtsx driver), and
irqdomain fix for db8550-prcmu, and some more cosmetic fixes for
arizona and wm5102."
* tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: rtsx: Fix oops when rtsx_pci_sdmmc is not probed
mfd: wm5102: Fix definition of WM5102_MAX_REGISTER
mfd: twl4030: Don't warn about uninitialized return code
mfd: da9052/53 lockup fix
mfd: rtsx: Add clock divider hook
mmc: rtsx: Call MFD hook to switch output voltage
mfd: rtsx: Add output voltage switch hook
mfd: Fix compile errors and warnings when !CONFIG_AB8500_BM
mfd: vexpress: Export global functions to fix build error
mfd: arizona: Check errors from regcache_sync()
mfd: tc3589x: Use simple irqdomain
mfd: pcf50633: Init pcf->dev before using it
mfd: max77693: Init max77693->dev before using it
mfd: max77686: Init max77686->dev before using it
mfd: db8500-prcmu: Fix irqdomain usage
mfd: tps65910: Select REGMAP_IRQ in Kconfig to fix build error
mfd: arizona: Disable control interface reporting for WM5102 and WM5110
If rtsx_pci_sdmmc is not probed, function pointer pcr->slots[].card_event
will point to NULL, and thus rtsx_pci_card_detect will reference a NULL
pointer.
Check card_event pointer before referencing it can avoid kernel panic.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the twl4030_write_script function gets called with
a zero length argument, its return value does not
get set. We know that all scripts have a nonzero
length, but returning an error in case they ever
do is probably appropriate.
Without this patch, building omap2plus_defconfig results in:
drivers/mfd/twl4030-power.c: In function 'load_twl4030_script':
drivers/mfd/twl4030-power.c:414:5: error: 'err' may be used uninitialized in this function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: "Kristo, Tero" <t-kristo@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
An issue has been reported where the PMIC either locks up or fails to
respond following a system Reset. This could result in a second write
in which the bus writes the current content of the write buffer to address
of the last I2C access.
The failure case is where this unwanted write transfers incorrect data to
a critical register.
This patch fixes this issue to by following any read or write with a dummy read
to a safe register address. A safe register address is one where the contents
will not affect the operation of the system.
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add callback function conv_clk_and_div_n to convert between SSC clock
and its divider N.
For rtl8411, the formula to calculate SSC clock divider N is different
with the other card reader models.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Different card reader has different method to switch output voltage,
add this callback to let the card reader implement its individual switch
function.
This is needed as rtl8411 has a specific switch output voltage procedure.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vexpress-sysreg driver does not have to be initialized
early, when the platform doesn't require this. Unfortunately
in such case it wasn't initialized correctly - master site
lookup and config bridge registration were missing. Fixed now.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
If charging is started before USB enumeration of an Accessory
Charger Adapter has finished, the AB8500 will generate a
VBUS_ERROR. This in turn results in timeouts and delays the
enumeration with around 15 seconds. This patch delays the
charging and then ramps currents slowly to avoid VBUS errors.
The delay allows the enumeration to have finished before
charging is turned on.
Signed-off-by: Martin Sjoblom <martin.w.sjoblom@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
drivers/mfd/ab8500-core.c:1015:21: error: ‘ab8500_bm_data’ undeclared here
include/linux/mfd/abx500/ab8500-bm.h:445:13: warning: ‘ab8500_fg_reinit’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:448:13: warning: ‘ab8500_charger_usb_state_changed’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:451:29: warning: ‘ab8500_btemp_get’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:455:12: warning: ‘ab8500_btemp_get_batctrl_temp’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:463:12: warning: ‘ab8500_fg_inst_curr_blocking’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:442:12: warning: ‘ab8500_fg_inst_curr_done’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:447:26: warning: ‘ab8500_fg_get’ defined but not used
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Compiling vexpress client drivers as module results in error messages such as
ERROR: "__vexpress_config_func_get" [drivers/hwmon/vexpress.ko] undefined!
ERROR: "vexpress_config_func_put" [drivers/hwmon/vexpress.ko] undefined!
This is because the global functions in drivers/mfd/vexpress-config.c are not
exported. Fix it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the control bus is unrelabile we may hit errors during regcache_sync(),
especially given that it tends to be one the most dense bursts of I/O in
many systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes a regression in the TC3589x driver introduced in
commit 15e27b1088
"mfd: Provide the tc3589x with its own IRQ domain"
If a system with a TC3589x expander is booted and a base
IRQ is passed from platform data, a legacy domain will
be used. However, since the Ux500 is now switched to use
SPARSE_IRQ, no descriptors get allocated on-the-fly,
and we get a crash.
Fix this by switching to using the simple irqdomain that
will handle this uniformly and also allocates descriptors
explicitly.
Also fix two small whitespace errors in the vicinity while
we're at it.
Cc: stable@kernel.org
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current code uses pcf->dev in the dev_err call before setting it to
&client->dev. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current code uses max77693->dev in the dev_err call before setting it to
&i2c->dev. Fix it.
This patch also includes below cleanups:
- Move checking pdata earlier and show dev_err if no platform data found.
- Remove unnecessary err_regmap goto label.
- Unregister i2c devices if regmap init for muic fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current code uses max77686->dev in the dev_err call before setting it to
&i2c->dev. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes two issues with the DB8500 PRCMU irqdomain:
- You have to state the irq base 0 to get a linear domain
for the DT case from irq_domain_add_simple()
- The irqdomain was not used to translate the initial irq
request using irq_create_mapping() making the linear
case fail as it was lacking a proper descriptor.
I took this opportunity to fix two lines of whitespace
errors in related code as I was anyway messing around with
it.
Cc: stable@kernel.org
Acked-by Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TPS65910 mfd driver uses functions that are only avaiable when
REGMAP_IRQ is enabled. So "select REGMAP_IRQ" is added to mfd
Kconfig to fix below build error:
drivers/built-in.o: In function `tps65910_irq_exit':
/media/anil/kernel/drivers/mfd/tps65910.c:265: undefined reference to `regmap_del_irq_chip'
drivers/built-in.o: In function `tps65910_irq_init':
/media/anil/kernel/drivers/mfd/tps65910.c:254: undefined reference to `regmap_add_irq_chip'
drivers/built-in.o: In function `tps65910_i2c_probe':
/media/anil/kernel/drivers/mfd/tps65910.c:509: undefined reference to `regmap_irq_get_domain'
make: *** [vmlinux] Error 1
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rather than disabling the error reporting only for earlier revisions
unconditionally disable it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This brings in all of the mei and other fixes that are needed to continue
development in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the build error:
drivers/built-in.o: In function `twl_probe':
drivers/mfd/twl-core.c:1256: undefined reference to `devm_regmap_init_i2c'
make: *** [vmlinux] Error 1
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[ Samuel is busy, taking it directly - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
