Add "reset-post-delay-us" parameter to MDIO bus properties,
so it's possible to add a delay after reset deassert.
This is optional in case external hardware slows down
release of the reset signal.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of descriptions assume a PHY device, but since this binding
describes a MDIO bus which can have different kinds of MDIO devices
attached to it, rephrase some descriptions to be more general in that
regard.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the properties pertaining to the broken turn around or resets
were only documented in ethernet-phy.yaml while they are applicable
across all MDIO devices and not Ethernet PHYs specifically which are a
superset.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
An MDIO transaction normally starts with 32 1s as a preamble. However
not all devices requires such a preamble. Add a device tree property
which allows the preamble to be suppressed. This will half the size of
the MDIO transaction, allowing faster transactions. But it should only
be used when all devices on the bus support suppressed preamble.
Suggested-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO busses typically operate at 2.5MHz. However many devices can
operate at faster speeds. This then allows more MDIO transactions per
second, useful for Ethernet switch statistics, or Ethernet PHY TDR
data. Allow the bus speed to be configured, using the standard
"clock-frequency" property, which i2c busses use to indicate the bus
speed. Before using this property, ensure all devices on the bus do
actually support the requested clock speed.
Suggested-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove vendor specific compatible string from example, otherwise DT YAML
schemas validation may trigger warnings specific to TI ti,davinci_mdio
and not to the generic MDIO example.
For example, the "bus_freq" is required for davinci_mdio, but not required for
generic mdio example. As result following warning will be produced:
mdio.example.dt.yaml: mdio@5c030000: 'bus_freq' is a required property
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The child nodes of a mdio bus are supposed to be ethernet PHYs, with a reg
property. Make sure that's validated as well.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
MDIO controllers should have child nodes with a singe value in their reg
properties being the ID of the PHY in the bus.
Let's add the proper constraints on #address-cells and #size-cells.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The node name of an MDIO controller should be MDIO. Let's add a rule for
this.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The MDIO buses have a number of available device tree properties that can
be used in their device tree node. Add a YAML schemas for those.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
