Pull i2c updates from Wolfram Sang:
"For 3.19, the I2C subsystem has to offer special candy this time.
Right in time for Christmas :)
- I2C slave framework: finally, a generic mechanism for Linux being
an I2C slave (if the bus driver supports that). Docs are still
missing but will come later this cycle, the code is good enough to
go.
- I2C muxes represent their topology in sysfs much more detailed.
This will help users to navigate around much easier.
- irq population of i2c clients is now done at probe time, not device
creation time, to have better support for deferred probing.
- new drivers for Imagination SCB, Amlogic Meson
- DMA support added for Freescale IMX, Renesas SHMobile
- slightly bigger driver updates to OMAP, i801, AT91, and rk3x
(mostly quirk handling, timing updates, and using better kernel
interfaces)
- eeprom driver can now write with byte-access (very slow, but OK to
have)
- and the bunch of smaller fixes, cleanups, ID updates..."
* 'i2c/for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (56 commits)
i2c: sh_mobile: remove unneeded DMA mask
i2c: rcar: add slave support
i2c: slave-eeprom: add eeprom simulator driver
i2c: core changes for slave support
MAINTAINERS: add I2C dt bindings also to I2C realm
i2c: designware: Fix falling time bindings doc
i2c: davinci: switch to use platform_get_irq
Documentation: i2c: Use PM ops instead of legacy suspend/resume
i2c: sh_mobile: optimize irq entry
i2c: pxa: add support for SCCB devices
omap: i2c: don't check bus state IP rev3.3 and earlier
i2c: s3c2410: Handle i2c sys_cfg register in i2c driver
i2c: rk3x: add Kconfig dependency on COMMON_CLK
i2c: omap: add notes related to i2c multimaster mode
i2c: omap: don't reset controller if Arbitration Lost detected
i2c: omap: implement workaround for handling invalid BB-bit values
i2c: omap: cleanup register definitions
i2c: rk3x: handle dynamic clock rate changes correctly
i2c: at91: enable probe deferring on dma channel request
i2c: at91: remove legacy DMA support
...
Pull x86 fixes from Ingo Molnar:
"Misc fixes (mainly Andy's TLS fixes), plus a cleanup"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tls: Disallow unusual TLS segments
x86/tls: Validate TLS entries to protect espfix
MAINTAINERS: Add me as x86 VDSO submaintainer
x86/asm: Unify segment selector defines
x86/asm: Guard against building the 32/64-bit versions of the asm-offsets*.c file directly
x86_64, switch_to(): Load TLS descriptors before switching DS and ES
x86/mm: Use min() instead of min_t() in the e820 printout code
x86/mm: Fix zone ranges boot printout
x86/doc: Update documentation after file shuffling
Pull audit updates from Paul Moore:
"Two small patches from the audit next branch; only one of which has
any real significant code changes, the other is simply a MAINTAINERS
update for audit.
The single code patch is pretty small and rather straightforward, it
changes the audit "version" number reported to userspace from an
integer to a bitmap which is used to indicate the functionality of the
running kernel. This really doesn't have much impact on the kernel,
but it will make life easier for the audit userspace folks.
Thankfully we were still on a version number which allowed us to do
this without breaking userspace"
* 'upstream' of git://git.infradead.org/users/pcmoore/audit:
audit: convert status version to a feature bitmap
audit: add Paul Moore to the MAINTAINERS entry
Merge second patchbomb from Andrew Morton:
- the rest of MM
- misc fs fixes
- add execveat() syscall
- new ratelimit feature for fault-injection
- decompressor updates
- ipc/ updates
- fallocate feature creep
- fsnotify cleanups
- a few other misc things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (99 commits)
cgroups: Documentation: fix trivial typos and wrong paragraph numberings
parisc: percpu: update comments referring to __get_cpu_var
percpu: update local_ops.txt to reflect this_cpu operations
percpu: remove __get_cpu_var and __raw_get_cpu_var macros
fsnotify: remove destroy_list from fsnotify_mark
fsnotify: unify inode and mount marks handling
fallocate: create FAN_MODIFY and IN_MODIFY events
mm/cma: make kmemleak ignore CMA regions
slub: fix cpuset check in get_any_partial
slab: fix cpuset check in fallback_alloc
shmdt: use i_size_read() instead of ->i_size
ipc/shm.c: fix overly aggressive shmdt() when calls span multiple segments
ipc/msg: increase MSGMNI, remove scaling
ipc/sem.c: increase SEMMSL, SEMMNI, SEMOPM
ipc/sem.c: change memory barrier in sem_lock() to smp_rmb()
lib/decompress.c: consistency of compress formats for kernel image
decompress_bunzip2: off by one in get_next_block()
usr/Kconfig: make initrd compression algorithm selection not expert
fault-inject: add ratelimit option
ratelimit: add initialization macro
...
My current email address will be gone shortly, update my email to be a
gmail one.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Cc: Timur Tabi <timur@tabi.org>
Cc: Takashi Iwai <tiwai@suse.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull dmaengine updates from Vinod Koul:
"Main features this time are:
- BAM v1.3.0 support form qcom bam dma
- support for Allwinner sun8i dma
- atmels eXtended DMA Controller driver
- chancnt cleanup by Maxime
- fixes spread over drivers"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (56 commits)
dmaenegine: Delete a check before free_percpu()
dmaengine: ioatdma: fix dma mapping errors
dma: cppi41: add a delay while setting the TD bit
dma: cppi41: wait longer for the HW to return the descriptor
dmaengine: fsl-edma: fixup reg offset and hw S/G support in big-endian model
dmaengine: fsl-edma: fix calculation of remaining bytes
drivers/dma/pch_dma: declare pch_dma_id_table as static
dmaengine: ste_dma40: fix error return code
dma: imx-sdma: clarify about firmware not found error
Documentation: devicetree: Fix Xilinx VDMA specification
dmaengine: pl330: update author info
dmaengine: clarify the issue_pending expectations
dmaengine: at_xdmac: Add DMA_PRIVATE
ARM: dts: at_xdmac: fix bad value of dma-cells in documentation
dmaengine: at_xdmac: fix missing spin_unlock
dmaengine: at_xdmac: fix a bug in transfer residue computation
dmaengine: at_xdmac: fix software lockup at_xdmac_tx_status()
dmaengine: at_xdmac: remove chancnt affectation
dmaengine: at_xdmac: prefer usage of readl/writel_relaxed
dmaengine: xdmac: fix print warning on dma_addr_t variable
...
Pull MIPS updates from Ralf Baechle:
"This is an unusually large pull request for MIPS - in parts because
lots of patches missed the 3.18 deadline but primarily because some
folks opened the flood gates.
- Retire the MIPS-specific phys_t with the generic phys_addr_t.
- Improvments for the backtrace code used by oprofile.
- Better backtraces on SMP systems.
- Cleanups for the Octeon platform code.
- Cleanups and fixes for the Loongson platform code.
- Cleanups and fixes to the firmware library.
- Switch ATH79 platform to use the firmware library.
- Grand overhault to the SEAD3 and Malta interrupt code.
- Move the GIC interrupt code to drivers/irqchip
- Lots of GIC cleanups and updates to the GIC code to use modern IRQ
infrastructures and features of the kernel.
- OF documentation updates for the GIC bindings
- Move GIC clocksource driver to drivers/clocksource
- Merge GIC clocksource driver with clockevent driver.
- Further updates to bring the GIC clocksource driver up to date.
- R3000 TLB code cleanups
- Improvments to the Loongson 3 platform code.
- Convert pr_warning to pr_warn.
- Merge a bunch of small lantiq and ralink fixes that have been
staged/lingering inside the openwrt tree for a while.
- Update archhelp for IP22/IP32
- Fix a number of issues for Loongson 1B.
- New clocksource and clockevent driver for Loongson 1B.
- Further work on clk handling for Loongson 1B.
- Platform work for Broadcom BMIPS.
- Error handling cleanups for TurboChannel.
- Fixes and optimization to the microMIPS support.
- Option to disable the FTLB.
- Dump more relevant information on machine check exception
- Change binfmt to allow arch to examine PT_*PROC headers
- Support for new style FPU register model in O32
- VDSO randomization.
- BCM47xx cleanups
- BCM47xx reimplement the way the kernel accesses NVRAM information.
- Random cleanups
- Add support for ATH25 platforms
- Remove pointless locking code in some PCI platforms.
- Some improvments to EVA support
- Minor Alchemy cleanup"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (185 commits)
MIPS: Add MFHC0 and MTHC0 instructions to uasm.
MIPS: Cosmetic cleanups of page table headers.
MIPS: Add CP0 macros for extended EntryLo registers
MIPS: Remove now unused definition of phys_t.
MIPS: Replace use of phys_t with phys_addr_t.
MIPS: Replace MIPS-specific 64BIT_PHYS_ADDR with generic PHYS_ADDR_T_64BIT
PCMCIA: Alchemy Don't select 64BIT_PHYS_ADDR in Kconfig.
MIPS: lib: memset: Clean up some MIPS{EL,EB} ifdefery
MIPS: iomap: Use __mem_{read,write}{b,w,l} for MMIO
MIPS: <asm/types.h> fix indentation.
MAINTAINERS: Add entry for BMIPS multiplatform kernel
MIPS: Enable VDSO randomization
MIPS: Remove a temporary hack for debugging cache flushes in SMTC configuration
MIPS: Remove declaration of obsolete arch_init_clk_ops()
MIPS: atomic.h: Reformat to fit in 79 columns
MIPS: Apply `.insn' to fixup labels throughout
MIPS: Fix microMIPS LL/SC immediate offsets
MIPS: Kconfig: Only allow 32-bit microMIPS builds
MIPS: signal.c: Fix an invalid cast in ISA mode bit handling
MIPS: mm: Only build one microassembler that is suitable
...
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
This became a fairly large pull request. In addition to the usual
driver updates / fixes, there have been a high amount of cleanups in
ASoC area, as well as control API helpers and kernel documentations
fixes touching through the whole tree.
In the driver side, the biggest changes are the support for new Intel
SoC found on new x86 machines, and the updates of FireWire dice and
oxfw drivers.
Some remarkable items are below:
* ALSA core
- PCM mmap code cleanup, removal of arch-dependent codes
- PCM xrun injection support
- PCM hwptr tracepoint support
- Refactoring of snd_pcm_action(), simplification of PCM locking
- Robustified sequecner auto-load functionality
- New control API helpers and lots of cleanups along with them
- Lots of kerneldoc fixes and cleanups
* USB-audio
- The mixer resume code was largely rewritten, and the devices with
quirks are resumed properly.
- New hardware support: Focusrite Scarlett, Digidesign Mbox1,
Denon/Marantz DACs, Zoom R16/24
* FireWire
- DICE driver updates with better duplex and sync support, including
MIDI support
- New OXFW driver for Oxford Semiconductor FW970/971 chipset,
including the previous LaCie Speakers device. Fullduplex and MIDI
support included as well as DICE driver.
* HD-audio
- Refactoring the driver-caps quirk handling in snd-hda-intel
- More consistent control names representing the topology better
- Fixups: HP mute LED with ALC268 codec, Ideapad S210 built-in mic
fix, ASUS Z99He laptop EAPD
* ASoC
- Conversion of AC'97 drivers to use regmap, bringing us closer to
the removal of the ASoC level I/O code
- Clean up a lot of old drivers that were open coding things that
have subsequently been implemented in the core
- Some DAPM performance improvements
- Removal of the now seldom used CODEC mutex
- Lots of updates for the newer Intel SoC support, including support
for the DSP and some Cherrytrail and Braswell machine drivers
- Support for Samsung boards using rt5631 as the CODEC
- Removal of the obsolete AFEB9260 machine driver
- Driver support for the TI TS3A227E headset driver used in some
Chrombeooks
* Others
- ASIHPI driver update and cleanups
- Lots of dev_*() printk conversions
- Lots of trivial cleanups for the codes spotted by Coccinelle
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sB6v
-----END PGP SIGNATURE-----
Merge tag 'sound-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became a fairly large pull request. In addition to the usual
driver updates / fixes, there have been a high amount of cleanups in
ASoC area, as well as control API helpers and kernel documentations
fixes touching through the whole tree.
In the driver side, the biggest changes are the support for new Intel
SoC found on new x86 machines, and the updates of FireWire dice and
oxfw drivers.
Some remarkable items are below:
ALSA core:
- PCM mmap code cleanup, removal of arch-dependent codes
- PCM xrun injection support
- PCM hwptr tracepoint support
- Refactoring of snd_pcm_action(), simplification of PCM locking
- Robustified sequecner auto-load functionality
- New control API helpers and lots of cleanups along with them
- Lots of kerneldoc fixes and cleanups
USB-audio:
- The mixer resume code was largely rewritten, and the devices with
quirks are resumed properly.
- New hardware support: Focusrite Scarlett, Digidesign Mbox1,
Denon/Marantz DACs, Zoom R16/24
FireWire:
- DICE driver updates with better duplex and sync support, including
MIDI support
- New OXFW driver for Oxford Semiconductor FW970/971 chipset,
including the previous LaCie Speakers device. Fullduplex and MIDI
support included as well as DICE driver.
HD-audio:
- Refactoring the driver-caps quirk handling in snd-hda-intel
- More consistent control names representing the topology better
- Fixups: HP mute LED with ALC268 codec, Ideapad S210 built-in mic
fix, ASUS Z99He laptop EAPD
ASoC:
- Conversion of AC'97 drivers to use regmap, bringing us closer to
the removal of the ASoC level I/O code
- Clean up a lot of old drivers that were open coding things that
have subsequently been implemented in the core
- Some DAPM performance improvements
- Removal of the now seldom used CODEC mutex
- Lots of updates for the newer Intel SoC support, including support
for the DSP and some Cherrytrail and Braswell machine drivers
- Support for Samsung boards using rt5631 as the CODEC
- Removal of the obsolete AFEB9260 machine driver
- Driver support for the TI TS3A227E headset driver used in some
Chrombeooks
Others:
- ASIHPI driver update and cleanups
- Lots of dev_*() printk conversions
- Lots of trivial cleanups for the codes spotted by Coccinelle"
* tag 'sound-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (594 commits)
ALSA: pcxhr: NULL dereference on probe failure
ALSA: lola: NULL dereference on probe failure
ALSA: hda - Add "eapd" model string for AD1986A codec
ALSA: hda - Add EAPD fixup for ASUS Z99He laptop
ALSA: oxfw: Add hwdep interface
ALSA: oxfw: Add support for capture/playback MIDI messages
ALSA: oxfw: add support for capturing PCM samples
ALSA: oxfw: Add support AMDTP in-stream
ALSA: oxfw: Add support for Behringer/Mackie devices
ALSA: oxfw: Change the way to start stream
ALSA: oxfw: Add proc interface for debugging purpose
ALSA: oxfw: Change the way to make PCM rules/constraints
ALSA: oxfw: Add support for AV/C stream format command to get/set supported stream formation
ALSA: oxfw: Change the way to name card
ALSA: dice: Add support for MIDI capture/playback
ALSA: dice: Add support for capturing PCM samples
ALSA: dice: Support for non SYT-Match sampling clock source mode
ALSA: dice: Add support for duplex streams with synchronization
ALSA: dice: Change the way to start stream
ALSA: jack: Add dummy snd_jack_set_key() definition
...
* support for mx6sl and mx6sx
* OMAP HDMI audio rewrite to make it finally work
* OMAP video PLL work to prepare for new DRA7xx SoCs
* simplefb DT related improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VAZB
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- support for mx6sl and mx6sx
- OMAP HDMI audio rewrite to make it finally work
- OMAP video PLL work to prepare for new DRA7xx SoCs
- simplefb DT related improvements
* tag 'fbdev-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (81 commits)
video: uvesafb: Deletion of an unnecessary check before the function call "platform_device_put"
video: fbdev-VIA: Deletion of an unnecessary check before the function call "framebuffer_release"
video: fbdev-MMP: Deletion of an unnecessary check before the function call "mmp_unregister_path"
video: mx3fb: Deletion of an unnecessary check before the function call "backlight_device_unregister"
video: fbdev-OMAP2: Deletion of unnecessary checks before the function call "i2c_put_adapter"
video: fbdev-SIS: Deletion of unnecessary checks before the function call "pci_dev_put"
video: smscufx: Deletion of unnecessary checks before the function call "vfree"
video: udlfb: Deletion of unnecessary checks before the function call "vfree"
video: uvesafb: Deletion of an unnecessary check before the function call "uvesafb_free"
video: fbdev-LCDC: Deletion of an unnecessary check before the function call "vfree"
video: fbdev: arkfb: suppress build warning
video: fbdev: s3fb: suppress build warning
video: fbdev: vt8623fb: suppress build warning
OMAPDSS: hdmi5: Fix bit field for IEC958_AES2_CON_SOURCE
OMAPDSS: hdmi: Remove __exit qualifier from hdmi_uninit_output()
OMAPDSS: hdmi5: Change hdmi_wp idlemode to to no_idle for audio playback
OMAPDSS: Remove all references to obsolete HDMI audio callbacks
ASoC: omap: Remove obsolete HDMI audio code and Kconfig options
OMAPDSS: hdmi5: Register ASoC platform device for omap hdmi audio
OMAPDSS: hdmi5: Remove callbacks for the old ASoC DAI driver
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i7gx
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Two new dvb frontend drivers: mn88472 and mn88473
- A new driver for some PCIe DVBSky cards
- A new remote controller driver: meson-ir
- One LIRC staging driver got rewritten and promoted to mainstream:
igorplugusb
- A new tuner driver (m88rs6000t)
- The old omap2 media driver got removed from staging. This driver
uses an old DMA API and it is likely broken on recent kernels.
Nobody cared enough to fix it
- Media bus format moved to a separate header, as DRM will also use the
definitions there
- mem2mem_testdev were renamed to vim2m, in order to use the same
naming convention taken by the other virtual test driver (vivid)
- Added a new driver for coda SoC (coda-jpeg)
- The cx88 driver got converted to use videobuf2 core
- Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
cores
- Lots of other fixes, improvements and cleanups on the drivers.
* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
[media] mn88473: One function call less in mn88473_init() after error
[media] mn88473: Remove uneeded check before release_firmware()
[media] lirc_zilog: Deletion of unnecessary checks before vfree()
[media] MAINTAINERS: Add myself as img-ir maintainer
[media] img-ir: Don't set driver's module owner
[media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
[media] img-ir/hw: Drop [un]register_decoder declarations
[media] img-ir/hw: Fix potential deadlock stopping timer
[media] img-ir/hw: Always read data to clear buffer
[media] redrat3: ensure dma is setup properly
[media] ddbridge: remove unneeded check before dvb_unregister_device()
[media] si2157: One function call less in si2157_init() after error
[media] tuners: remove uneeded checks before release_firmware()
[media] arm: omap2: rx51-peripherals: fix build warning
[media] stv090x: add an extra protetion against buffer overflow
[media] stv090x: Remove an unreachable code
[media] stv090x: Some whitespace cleanups
[media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
[media] si2168: add support for firmware files in new format
[media] si2168: debug printout for firmware version
...
- Simplify Device Tree initialisation; lp855x_bl
- Add Regulator support; lp855x
- Remove Bryan from the Maintainer list -- new baby, no time :)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0PNI
-----END PGP SIGNATURE-----
Merge tag 'backlight-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
- Clean-up leaky resources; pwm_bl
- Simplify Device Tree initialisation; lp855x_bl
- Add Regulator support; lp855x
- Remove Bryan from the Maintainer list -- new baby, no time :)
* tag 'backlight-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
MAINTAINERS: Remove my name from Backlight subsystem
backlight: lp855x: Add supply regulator to lp855x
backlight: lp855x: Refactor DT parsing code
backlight: pwm: Clean-up pwm requested using legacy API
- Force conversion of the ux500 pin control device trees
and parsers to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm
PMIC MPP pin controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller,
the first Intel pin controller to fully take advantage of
the pin control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sxpe
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"Here is a stash of pin control changes I have collected for the v3.19
series. Mainly new hardware support, with Intels new embedded SoC as
the especially interesting thing standing out, fully using the
subsystem.
- Force conversion of the ux500 pin control device trees and parsers
to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm PMIC MPP pin
controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller, the
first Intel pin controller to fully take advantage of the pin
control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes"
* tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (49 commits)
pinctrl: at91: enhance (debugfs) at91_gpio_dbg_show
pinctrl: meson: add device tree bindings documentation
gpio: tz1090: Fix error handling of irq_of_parse_and_map
pinctrl: tz1090-pinctrl.txt: Fix typo in binding
pinctrl: pinconf-generic: Declare dt_params/conf_items const
pinctrl: exynos: Add support for Exynos4415
pinctrl: exynos: Add initial driver data for Exynos7
pinctrl: exynos: Add irq_chip instance for Exynos7 wakeup interrupts
pinctrl: exynos: Consolidate irq domain callbacks
pinctrl: exynos: Generalize the eint16_31 demux code
pinctrl: samsung: Separate per-bank init and runtime data
pinctrl: samsung: Constify samsung_pin_ctrl struct
pinctrl: samsung: Constify samsung_pin_bank_type struct
pinctrl: samsung: Drop unused label field in samsung_pin_ctrl struct
pinctrl: samsung: Make samsung_pinctrl_get_soc_data use ERR_PTR()
pinctrl: Add Intel Cherryview/Braswell pin controller support
gpio / ACPI: Add knowledge about pin controllers to acpi_get_gpiod()
pinctrl: Fix path error in documentation
pinctrl: rockchip: save and restore gpio6_c6 pinmux in suspend/resume
pinctrl: rockchip: add suspend/resume functions
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
Merge first patchbomb from Andrew Morton:
- a few minor cifs fixes
- dma-debug upadtes
- ocfs2
- slab
- about half of MM
- procfs
- kernel/exit.c
- panic.c tweaks
- printk upates
- lib/ updates
- checkpatch updates
- fs/binfmt updates
- the drivers/rtc tree
- nilfs
- kmod fixes
- more kernel/exit.c
- various other misc tweaks and fixes
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (190 commits)
exit: pidns: fix/update the comments in zap_pid_ns_processes()
exit: pidns: alloc_pid() leaks pid_namespace if child_reaper is exiting
exit: exit_notify: re-use "dead" list to autoreap current
exit: reparent: call forget_original_parent() under tasklist_lock
exit: reparent: avoid find_new_reaper() if no children
exit: reparent: introduce find_alive_thread()
exit: reparent: introduce find_child_reaper()
exit: reparent: document the ->has_child_subreaper checks
exit: reparent: s/while_each_thread/for_each_thread/ in find_new_reaper()
exit: reparent: fix the cross-namespace PR_SET_CHILD_SUBREAPER reparenting
exit: reparent: fix the dead-parent PR_SET_CHILD_SUBREAPER reparenting
exit: proc: don't try to flush /proc/tgid/task/tgid
exit: release_task: fix the comment about group leader accounting
exit: wait: drop tasklist_lock before psig->c* accounting
exit: wait: don't use zombie->real_parent
exit: wait: cleanup the ptrace_reparented() checks
usermodehelper: kill the kmod_thread_locker logic
usermodehelper: don't use CLONE_VFORK for ____call_usermodehelper()
fs/hfs/catalog.c: fix comparison bug in hfs_cat_keycmp
nilfs2: fix the nilfs_iget() vs. nilfs_new_inode() races
...
Mark these as subscriber-only mailing lists.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the external page_cgroup data structure and its lookup is gone,
the only code remaining in there is swap slot accounting.
Rename it and move the conditional compilation into mm/Makefile.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull cifs update from Steve French:
"Mostly cifs cleanup but also a few cifs fixes"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
cifs: remove unneeded condition check
Set UID in sess_auth_rawntlmssp_authenticate too
cifs: convert printk(LEVEL...) to pr_<level>
cifs: convert to print_hex_dump() instead of custom implementation
cifs: call strtobool instead of custom implementation
Update MAINTAINERS entry
Update modinfo cifs version for cifs.ko
decode_negTokenInit had wrong calling sequence
Add missing defines for ACL query support
Add support for original fallocate
The GPMC driver has traditionally been considered a part of the
OMAP platform code and tightly interweaved with some of the boards.
With this cleanup, it has finally come to the point where it makes
sense to move it out of arch/arm into drivers/memory, where we already
have other drivers for similar hardware. The cleanups are still
ongoing, with the goal of eventually having a standalone driver
that does not require an interface to architecture code.
This is a separate branch because of dependencies on multiple other
branches, and to keep the drivers changes separate from the normal
cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=U4Fz
-----END PGP SIGNATURE-----
Merge tag 'omap-gpmc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC/OMAP GPMC driver cleanup and move from Arnd Bergmann:
"The GPMC driver has traditionally been considered a part of the OMAP
platform code and tightly interweaved with some of the boards.
With this cleanup, it has finally come to the point where it makes
sense to move it out of arch/arm into drivers/memory, where we already
have other drivers for similar hardware. The cleanups are still
ongoing, with the goal of eventually having a standalone driver that
does not require an interface to architecture code.
This is a separate branch because of dependencies on multiple other
branches, and to keep the drivers changes separate from the normal
cleanups"
* tag 'omap-gpmc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
memory: gpmc: Move omap gpmc code to live under drivers
ARM: OMAP2+: Move GPMC initcall to devices.c
ARM: OMAP2+: Prepare to move GPMC to drivers by platform data header
ARM: OMAP2+: Remove unnecesary include in GPMC driver
ARM: OMAP2+: Drop board file for 3430sdp
ARM: OMAP2+: Drop board file for ti8168evm
ARM: OMAP2+: Drop legacy code for gpmc-smc91x.c
ARM: OMAP2+: Require proper GPMC timings for devices
ARM: OMAP2+: Show bootloader GPMC timings to allow configuring the .dts file
ARM: OMAP2+: Fix support for multiple devices on a GPMC chip select
ARM: OMAP2+: gpmc: Sanity check GPMC fck on probe
ARM: OMAP2+: gpmc: Keep Chip Select disabled while configuring it
ARM: OMAP2+: gpmc: Always enable A26-A11 for non NAND devices
ARM: OMAP2+: gpmc: Error out if timings fail in gpmc_probe_generic_child()
ARM: OMAP2+: gpmc: Print error message in set_gpmc_timing_reg()
John W. Linville says:
====================
pull request: wireless-next 2014-12-08
Please pull this last batch of pending wireless updates for the 3.19 tree...
For the wireless bits, Johannes says:
"This time I have Felix's no-status rate control work, which will allow
drivers to work better with rate control even if they don't have perfect
status reporting. In addition to this, a small hwsim fix from Patrik,
one of the regulatory patches from Arik, and a number of cleanups and
fixes I did myself.
Of note is a patch where I disable CFG80211_WEXT so that compatibility
is no longer selectable - this is intended as a wake-up call for anyone
who's still using it, and is still easily worked around (it's a one-line
patch) before we fully remove the code as well in the future."
For the Bluetooth bits, Johan says:
"Here's one more bluetooth-next pull request for 3.19:
- Minor cleanups for ieee802154 & mac802154
- Fix for the kernel warning with !TASK_RUNNING reported by Kirill A.
Shutemov
- Support for another ath3k device
- Fix for tracking link key based security level
- Device tree bindings for btmrvl + a state update fix
- Fix for wrong ACL flags on LE links"
And...
"In addition to the previous one this contains two more cleanups to
mac802154 as well as support for some new HCI features from the
Bluetooth 4.2 specification.
From the original request:
'Here's what should be the last bluetooth-next pull request for 3.19.
It's rather large but the majority of it is the Low Energy Secure
Connections feature that's part of the Bluetooth 4.2 specification. The
specification went public only this week so we couldn't publish the
corresponding code before that. The code itself can nevertheless be
considered fairly mature as it's been in development for over 6 months
and gone through several interoperability test events.
Besides LE SC the pull request contains an important fix for command
complete events for mgmt sockets which also fixes some leaks of hci_conn
objects when powering off or unplugging Bluetooth adapters.
A smaller feature that's part of the pull request is service discovery
support. This is like normal device discovery except that devices not
matching specific UUIDs or strong enough RSSI are filtered out.
Other changes that the pull request contains are firmware dump support
to the btmrvl driver, firmware download support for Broadcom BCM20702A0
variants, as well as some coding style cleanups in 6lowpan &
ieee802154/mac802154 code.'"
For the NFC bits, Samuel says:
"With this one we get:
- NFC digital improvements for DEP support: Chaining, NACK and ATN
support added.
- NCI improvements: Support for p2p target, SE IO operand addition,
SE operands extensions to support proprietary implementations, and
a few fixes.
- NFC HCI improvements: OPEN_PIPE and NOTIFY_ALL_CLEARED support,
and SE IO operand addition.
- A bunch of minor improvements and fixes for STMicro st21nfcb and
st21nfca"
For the iwlwifi bits, Emmanuel says:
"Major works are CSA and TDLS. On top of that I have a new
firmware API for scan and a few rate control improvements.
Johannes find a few tricks to improve our CPU utilization
and adds support for a new spin of 7265 called 7265D.
Along with this a few random things that don't stand out."
And...
"I deprecate here -8.ucode since -9 has been published long ago.
Along with that I have a new activity, we have now better
a infrastructure for firmware debugging. This will allow to
have configurable probes insides the firmware.
Luca continues his work on NetDetect, this feature is now
complete. All the rest is minor fixes here and there."
For the Atheros bits, Kalle says:
"Only ath10k changes this time and no major changes. Most visible are:
o new debugfs interface for runtime firmware debugging (Yanbo)
o fix shared WEP (Sujith)
o don't rebuild whenever kernel version changes (Johannes)
o lots of refactoring to make it easier to add new hw support (Michal)
There's also smaller fixes and improvements with no point of listing
here."
In addition, there are a few last minute updates to ath5k,
ath9k, brcmfmac, brcmsmac, mwifiex, rt2x00, rtlwifi, and wil6210.
Also included is a pull of the wireless tree to pick-up the fixes
originally included in "pull request: wireless 2014-12-03"...
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
New and updated SoC support, notable changes include:
* bcm: brcmstb SMP support
* bcm: initial iproc/cygnus support
* exynos: Exynos4415 SoC support
* exynos: PMU and suspend support for Exynos5420
* exynos: PMU support for Exynos3250
* exynos: pm related maintenance
* imx: new LS1021A SoC support
* imx: vybrid 610 global timer support
* integrator: convert to using multiplatform configuration
* mediatek: earlyprintk support for mt8127/mt8135
* meson: meson8 soc and l2 cache controller support
* mvebu: Armada 38x CPU hotplug support
* mvebu: drop support for prerelease Armada 375 Z1 stepping
* mvebu: extended suspend support, now works on Armada 370/XP
* omap: hwmod related maintenance
* omap: prcm cleanup
* pxa: initial pxa27x DT handling
* rockchip: SMP support for rk3288
* rockchip: add cpu frequency scaling support
* shmobile: r8a7740 power domain support
* shmobile: various small restart, timer, pci apmu changes
* sunxi: Allwinner A80 (sun9i) earlyprintk support
* ux500: power domain support
Overall, a significant chunk of changes, coming mostly from
the usual suspects: omap, shmobile, samsung and mvebu, all of
which already contain a lot of platform specific code in
arch/arm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lFoH
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support, notable changes include:
- bcm:
brcmstb SMP support
initial iproc/cygnus support
- exynos:
Exynos4415 SoC support
PMU and suspend support for Exynos5420
PMU support for Exynos3250
pm related maintenance
- imx:
new LS1021A SoC support
vybrid 610 global timer support
- integrator:
convert to using multiplatform configuration
- mediatek:
earlyprintk support for mt8127/mt8135
- meson:
meson8 soc and l2 cache controller support
- mvebu:
Armada 38x CPU hotplug support
drop support for prerelease Armada 375 Z1 stepping
extended suspend support, now works on Armada 370/XP
- omap:
hwmod related maintenance
prcm cleanup
- pxa:
initial pxa27x DT handling
- rockchip:
SMP support for rk3288
add cpu frequency scaling support
- shmobile:
r8a7740 power domain support
various small restart, timer, pci apmu changes
- sunxi:
Allwinner A80 (sun9i) earlyprintk support
- ux500:
power domain support
Overall, a significant chunk of changes, coming mostly from the usual
suspects: omap, shmobile, samsung and mvebu, all of which already
contain a lot of platform specific code in arch/arm"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (187 commits)
ARM: mvebu: use the cpufreq-dt platform_data for independent clocks
soc: integrator: Add terminating entry for integrator_cm_match
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
ARM: add lolevel debug support for asm9260
ARM: add mach-asm9260
ARM: EXYNOS: use u8 for val[] in struct exynos_pmu_conf
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
...
The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
* Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one
SoC at a time. For 3.19, the r8a7791 platform and associated\
"Koelsch" board are considered complete and we remove the non-DT
non-multiplatform support for this.
* The ARM Versatile Express has supported DT and multiplatform
for a long time, but we have still kept the legacy board files
around, because not all drivers were fully working before. We
have finally taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches
or just unrelated to the more interesting changes:
* The dts files for arm64 get moved into per-vendor directories for
a clearer structure.
* Some dead code removal (zynq, exynos, davinci, imx)
* Using pr_*() macros more consistently instead of printk(KERN_*)
in some platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Apdh
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
- Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one SoC
at a time. For 3.19, the r8a7791 platform and associated "Koelsch"
board are considered complete and we remove the non-DT
non-multiplatform support for this.
- The ARM Versatile Express has supported DT and multiplatform for a
long time, but we have still kept the legacy board files around,
because not all drivers were fully working before. We have finally
taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches or
just unrelated to the more interesting changes:
- The dts files for arm64 get moved into per-vendor directories for a
clearer structure.
- Some dead code removal (zynq, exynos, davinci, imx)
- Using pr_*() macros more consistently instead of printk(KERN_*) in
some platform code"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (71 commits)
ARM: zynq: Remove secondary_startup() declaration from header
ARM: vexpress: Enable regulator framework when MMCI is in use
ARM: vexpress: Remove non-DT code
ARM: imx: Remove unneeded .map_io initialization
ARM: dts: imx6qdl-sabresd: Fix the microphone route
ARM: imx: refactor mxc_iomux_mode()
ARM: imx: simplify clk_pllv3_prepare()
ARM: imx6q: drop unnecessary semicolon
ARM: imx: clean up machine mxc_arch_reset_init_dt reset init
ARM: dts: imx6qdl-rex: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-gw5x: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-sabresd: Use IMX6QDL_CLK_CKO define
ARM: at91: remove useless init_time for DT-only SoCs
ARM: davinci: Remove redundant casts
ARM: davinci: Use standard logging styles
ARM: shmobile: r8a7779: Spelling/grammar s/entity/identity/, s/map/mapping/
ARM: shmobile: sh7372: Spelling/grammar s/entity map/identity mapping/
ARM: shmobile: sh73a0: Spelling/grammar s/entity map/identity mapping/
ARM: EXYNOS: Remove unused static iomapping
ARM: at91: fix build breakage due to legacy board removals
...
On Atmel AT91, the conversion to device tree is now considered complete,
and all machines that were not already converted in 3.18 are assumed to
be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the platform
itself is not "multiplatform"-enabled, but both issues are going to be
taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size
of the branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iD8DBQBUhyNX5t5GS2LDRf4RAnjxAKCER7eoLNadu1/93n/a9d1nUz4MoQCcCZUq
BolxCOi0wr4YTcQtp7rHzWI=
=ykAB
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup on mach-at91 from Arnd Bergmann:
"On Atmel AT91, the conversion to device tree is now considered
complete, and all machines that were not already converted in 3.18 are
assumed to be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the
platform itself is not "multiplatform"-enabled, but both issues are
going to be taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size of
the branch"
* tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91: remove unused board.h file
ARM: at91: remove unneeded header files
ARM: at91/clocksource: remove !DT PIT initializations
ARM: at91: at91rm9200 ST initialization is now DT only
ARM: at91: remove old AT91-specific drivers
ARM: at91: cleanup initilisation code by removing dead code
ARM: at91/Kconfig: select board files automatically
ARM: at91: remove unused IRQ function declarations
ARM: at91: remove legacy IRQ driver and related code
ARM: at91: remove old at91-specific clock driver
ARM: at91: remove clock data in at91sam9n12.c and at91sam9x5.c files
ARM: at91: remove all !DT related configuration options
ARM: at91/trivial: update Kconfig comment to mention SAMA5
ARM: at91: always USE_OF from now on
ARM: at91/Kconfig: remove ARCH_AT91RM9200 option for drivers
ARM: at91: switch configuration option to SOC_AT91RM9200
ARM: at91: remove at91rm9200 legacy board support
ARM: at91: remove at91rm9200 legacy boards files
ARM: at91/Kconfig: remove useless fbdev Kconfig options
ARM: at91: remove at91sam9261/at91sam9g10 legacy board support
...
These are bug fixes for harmless problems that were not important
enough to get fixed in 3.19. This contains updates to the MAINTAINERS
file, in particular:
- Ben Dooks stepped down as Samsung co-maintainer (thanks Ben for
long years of maintaining this). Kukjin Kim, who has been
doing the work de-facto by himself recently is now the
only maintainer.
- Liviu, Sudeep and Lorenzo from ARM now officially maintain the
Versatile Express platform, which was orphaned (thanks for
- Gregory Fong and Florian Fainelli help out on the Broadcom BCM7XXX
platform
- Ray Jui and Scott Branden are the future maintainers for the
newly merged Broadcom Cygnus platform. Welcome!
In terms of actual fixes, we have the usual set of OMAP bug fixes,
which Tony Lindgren separates out well from the other OMAP changes,
one really ep93xx regression fix against 3.11 that didn't make it for
3.18, a few GIC changes from Marc Zyngier as a preparation for
later rework (the current code is wrong in a harmless way), on
Tegra regression and one samsung spelling fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=J1gB
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"These are bug fixes for harmless problems that were not important
enough to get fixed in 3.19. This contains updates to the MAINTAINERS
file, in particular:
- Ben Dooks stepped down as Samsung co-maintainer (thanks Ben for
long years of maintaining this). Kukjin Kim, who has been doing
the work de-facto by himself recently is now the only maintainer.
- Liviu, Sudeep and Lorenzo from ARM now officially maintain the
Versatile Express platform, which was orphaned (thanks for
- Gregory Fong and Florian Fainelli help out on the Broadcom BCM7XXX
platform
- Ray Jui and Scott Branden are the future maintainers for the newly
merged Broadcom Cygnus platform. Welcome!
In terms of actual fixes, we have the usual set of OMAP bug fixes,
which Tony Lindgren separates out well from the other OMAP changes,
one really ep93xx regression fix against 3.11 that didn't make it for
3.18, a few GIC changes from Marc Zyngier as a preparation for later
rework (the current code is wrong in a harmless way), on Tegra
regression and one samsung spelling fix"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx6: fix bogus use of irq_get_irq_data
ARM: imx: irq: fix buggy usage of irq_data irq field
MAINTAINERS: ARM Versatile Express platform, add missing pattern
MAINTAINERS: ARM Versatile Express platform
arm: ep93xx: add dma_masks for the M2P and M2M DMA controllers
MAINTAINERS: Add ahci_st.c to ARCH/STI architecture
MAINTAINERS: add entry for the GISB arbiter driver
MAINTAINERS: update brcmstb entries
MAINTAINERS: update email address and cleanup for exynos entry
ARM: tegra: Re-add removed SoC id macro to tegra_resume()
MAINTAINERS: Entry for Cygnus/iproc arm architecture
ARM: OMAP: serial: remove last vestige of DTR_gpio support.
ARM: OMAP2+: gpmc: Get rid of "ti,elm-id not found" warning
ARM: EXYNOS: fix typo in static struct name "exynos5_list_diable_wfi_wfe"
ARM: OMAP2: Remove unnecessary KERN_* in omap_phy_internal.c
ARM: OMAP4+: Remove unused omap_l3_noc platform init
ARM: dts: Add twl keypad map for omap3 EVM
ARM: dts: Add twl keypad map for LDP
ARM: dts: Fix NAND last partition size on LDP
ARM: OMAP3: Fix errors for omap_l3_smx when booted with device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.5 (GNU/Linux)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=KmRf
-----END PGP SIGNATURE-----
Merge tag 'nios2-v3.19-rc1' of git://git.rocketboards.org/linux-socfpga-next
Pull Altera Nios II processor support from Ley Foon Tan:
"Here is the Linux port for Nios II processor (from Altera) arch/nios2/
tree for v3.19.
The patchset has been discussed on the kernel mailing lists since
April and has gone through 6 revisions of review. The additional
changes since then have been mostly further cleanups and fixes when
merged with other trees.
The arch code is in arch/nios2 and one asm-generic change (acked by
Arnd)"
Arnd Bergmann says:
"I've reviewed the architecture port in the past and it looks good in
its latest version"
Acked-by: Arnd Bergmann <arnd@arndb.de>
* tag 'nios2-v3.19-rc1' of git://git.rocketboards.org/linux-socfpga-next: (40 commits)
nios2: Make NIOS2_CMDLINE_IGNORE_DTB depend on CMDLINE_BOOL
nios2: Add missing NR_CPUS to Kconfig
nios2: asm-offsets: Remove unused definition TI_TASK
nios2: Remove write-only struct member from nios2_timer
nios2: Remove unused extern declaration of shm_align_mask
nios2: include linux/type.h in io.h
nios2: move include asm-generic/io.h to end of file
nios2: remove include asm-generic/iomap.h from io.h
nios2: remove unnecessary space before define
nios2: fix error handling of irq_of_parse_and_map
nios2: Use IS_ENABLED instead of #ifdefs to check config symbols
nios2: Build infrastructure
Documentation: Add documentation for Nios2 architecture
MAINTAINERS: Add nios2 maintainer
nios2: ptrace support
nios2: Module support
nios2: Nios2 registers
nios2: Miscellaneous header files
nios2: Cpuinfo handling
nios2: Time keeping
...
include/linux/thermal.h contains definitions for the Thermal generic
netlink family, but none of the valuable information relevant to
user-space such as the Genl family name, multicast group, version or
command set and data types is exported to user-space.
Export all the relevant generic netlink information to user-space to
make this genl family usable by user-space, and while at it, export
THERMAL_NAME_LENGTH since it limits name length for thermal_hwmon
devices.
Kbuild and MAINTAINERS are also updated accordingly to reflect this new
file: include/uapi/linux/thermal.h.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch is the usual mix of driver updates (srp, ipr, scsi_debug, NCR5380,
fnic, 53c974, ses, wd719x, hpsa, megaraid_sas). Of those, wd7a9x is new and
53c974 is a rewrite of the old tmscsim driver and the extensive work by Finn
Thain rewrites all the NCR5380 based drivers. There's also extensive
infrastructure updates: a new logging infrastructure for sense information and
a rewrite of the tagged command queue API and an assortment of minor updates.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJUhgazAAoJEDeqqVYsXL0MxIYH/2wCs9sne5cfDTjfufLJDdu1
WLoJgNMxv+14OukknJfG2Kk1WlHgLRM5+TVWIGiG0mmjXuFyShzIqEOHKTDWqxnE
tBH4wLi/+XYqZAmAeim4/2zhvf+cUVVlIu01VERR5uwaBWYM8BeLSwjdnAAvEEwb
iV74p1WV6frXo4guADplgtkjD0YxI4MTUZ1figRMlLO6WLFFyQ+95UfY8jFs+eQv
zk63y7Mm7dQNd57/Wl3i89lw0kqlaJSZNl8Ovj1axy4rDYzT1wXhY8mEwD8fI8Ym
wahldjFE5vXgj0NpO3tB3Z+UDP2YmQduMyzTxkPNnrEPKiOCsnQo42XR6vb92cQ=
=Y+DU
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch is the usual mix of driver updates (srp, ipr, scsi_debug,
NCR5380, fnic, 53c974, ses, wd719x, hpsa, megaraid_sas).
Of those, wd7a9x is new and 53c974 is a rewrite of the old tmscsim
driver and the extensive work by Finn Thain rewrites all the NCR5380
based drivers.
There's also extensive infrastructure updates: a new logging
infrastructure for sense information and a rewrite of the tagged
command queue API and an assortment of minor updates"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (183 commits)
scsi: set fmt to NULL scsi_extd_sense_format() by default
libsas: remove task_collector mode
wd719x: remove dma_cache_sync call
scsi_debug: add Report supported opcodes+tmfs; Compare and write
scsi_debug: change SCSI command parser to table driven
scsi_debug: add Capacity Changed Unit Attention
scsi_debug: append inject error flags onto scsi_cmnd object
scsi_debug: pinpoint invalid field in sense data
wd719x: Add firmware documentation
wd719x: Introduce Western Digital WD7193/7197/7296 PCI SCSI card driver
eeprom-93cx6: Add (read-only) support for 8-bit mode
esas2r: fix an oversight in setting return value
esas2r: fix an error path in esas2r_ioctl_handler
esas2r: fir error handling in do_fm_api
scsi: add SPC-3 command definitions
scsi: rename SERVICE_ACTION_IN to SERVICE_ACTION_IN_16
scsi: remove scsi_driver owner field
scsi: move scsi_dispatch_cmd to scsi_lib.c
scsi: stop passing a gfp_mask argument down the command setup path
scsi: remove scsi_next_command
...
* pm-cpuidle:
cpuidle: add MAINTAINERS entry for ARM Exynos cpuidle driver
drivers: cpuidle: Remove cpuidle-arm64 duplicate error messages
drivers: cpuidle: Add idle-state-name description to ARM idle states
drivers: cpuidle: Add status property to ARM idle states
cpuidle: Invert CPUIDLE_FLAG_TIME_VALID logic
Conflicts:
drivers/scsi/scsi_debug.c
Agreed and tested resolution to a merge problem between a fix in scsi_debug
and a driver update
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Update link to point to Steve's current tree on git.samba.org. Remove
link to the old patchwork instance which shows no new patches since 2010.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Steve French <smfrench@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhNLZAAoJEHm+PkMAQRiGAEcH/iclYDW7k2GKemMqboy+Ohmh
+ELbQothNhlGZlS1wWdD69LBiiXkkQ+ufVYFh/hC0oy0gUdfPMt5t+bOHy6cjn6w
9zOcACtpDKnqbOwRqXZjZgNmIabk7lRjbn7GK4GQqpIaW4oO0FWcT91FFhtGSPDa
tjtmGRqDmbNsqfzr18h0WPEpUZmT6MxIdv17AYDliPB1MaaRuAv1Kss05TJrXdfL
Oucv+C0uwnybD9UWAz6pLJ3H/HR9VJFdkaJ4Y0pbCHAuxdd1+swoTpicluHlsJA1
EkK5iWQRMpcmGwKvB0unCAQljNpaJiq4/Tlmmv8JlYpMlmIiVLT0D8BZx5q05QQ=
=oGNw
-----END PGP SIGNATURE-----
Merge tag 'v3.18' into drm-next
Linux 3.18
Backmerge Linus tree into -next as we had conflicts in i915/radeon/nouveau,
and everyone was solving them individually.
* tag 'v3.18': (57 commits)
Linux 3.18
watchdog: s3c2410_wdt: Fix the mask bit offset for Exynos7
uapi: fix to export linux/vm_sockets.h
i2c: cadence: Set the hardware time-out register to maximum value
i2c: davinci: generate STP always when NACK is received
ahci: disable MSI on SAMSUNG 0xa800 SSD
context_tracking: Restore previous state in schedule_user
slab: fix nodeid bounds check for non-contiguous node IDs
lib/genalloc.c: export devm_gen_pool_create() for modules
mm: fix anon_vma_clone() error treatment
mm: fix swapoff hang after page migration and fork
fat: fix oops on corrupted vfat fs
ipc/sem.c: fully initialize sem_array before making it visible
drivers/input/evdev.c: don't kfree() a vmalloc address
cxgb4: Fill in supported link mode for SFP modules
xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
mm/vmpressure.c: fix race in vmpressure_work_fn()
mm: frontswap: invalidate expired data on a dup-store failure
mm: do not overwrite reserved pages counter at show_mem()
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/nouveau/nouveau_drm.c
drivers/gpu/drm/radeon/radeon_cs.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MTIl
-----END PGP SIGNATURE-----
Merge tag 'media/v3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A core fix and some driver fixes:
- regression fix in Remote Controller core affecting RC6 protocol
handling
- fix video buffer handling in cx23885
- race fix in solo6x10
- fix image selection in smiapp
- fix reported payload size on s2255drv
- two updates for MAINTAINERS file"
* tag 'media/v3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] rc-core: fix toggle handling in the rc6 decoder
MAINTAINERS: Update mchehab's addresses
[media] cx23885: use sg = sg_next(sg) instead of sg++
[media] s2255drv: fix payload size for JPG, MJPEG
[media] Update MAINTAINERS for solo6x10
[media] solo6x10: fix a race in IRQ handler
[media] smiapp: Only some selection targets are settable
Add myself as the maintainer for the Imagination Technologies Infrared
Decoder driver.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
VE's reset driver lives at the third level of the directories:
drivers/power/reset/vexpress-poweroff.c
and wasn't matched by the */*/vexpress* pattern.
Added additional pattern for all files at this level. This should be
enough for a while...
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since there has been quite a lot of development going on for
ARM Exynos cpuidle driver recently I would like to add separate
MAINTAINERS entry for it and add myself as the primary maintainer.
The merging process would remain (almost) unchanged with patches
going (with my Ack) through Daniel's or Kukjin's tree.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch introduces the first driver to benefit from the switchdev
infrastructure and to implement newly introduced switch ndos. This is a
driver for emulated switch chip implemented in qemu:
https://github.com/sfeldma/qemu-rocker/
This patch is a result of joint work with Scott Feldman.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this is to provide a possibility to support various switch
chips. Drivers should implement relevant ndos to do so. Now there is
only one ndo defined:
- for getting physical switch id is in place.
Note that user can use random port netdevice to access the switch.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
further clean up work.
Note that we still have dependencies to the legacy booting for
omap3 board-*.c files for setting up the board specific memory
timings. For that we need the timing related things still exposed
in include/linux/omap-gpmc.h. This will all become private data
to the GPMC driver once the legacy booting support can be dropped.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O1GC
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.19/gpmc-move-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/omap-gpmc
Pull "move omap gpmc to drivers finally" from Tony Lindgren:
We can finally move the GPMC code to live in drivers/memory for
further clean up work.
Note that we still have dependencies to the legacy booting for
omap3 board-*.c files for setting up the board specific memory
timings. For that we need the timing related things still exposed
in include/linux/omap-gpmc.h. This will all become private data
to the GPMC driver once the legacy booting support can be dropped.
* tag 'omap-for-v3.19/gpmc-move-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
memory: gpmc: Move omap gpmc code to live under drivers
ARM: OMAP2+: Move GPMC initcall to devices.c
ARM: OMAP2+: Prepare to move GPMC to drivers by platform data header
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Just move to drivers as further clean-up can now happen there
finally.
Let's also add Roger and me to the MAINTAINERS so we get
notified for any patches related to GPMC.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a separate section for the ARM
Versatile Express platform maintainers, listing
all different bits and bobs used by it.
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds the ahci_st.c driver found on STMicroelectronics
stih41x consumer electronics SoC's into the STI arch section
of the maintainers file.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Amlogic Meson SoCs include a infrared remote control receiver that can
operate in two modes: "NEC" mode in which the hardware decodes frames
using the NEC IR protocol, and "general" mode in which the receiver
simply reports the duration of pulses and spaces for software
decoding.
This is a driver for the IR receiver that implements software decoding
of received frames.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add myself as the maintainer of the i.MX DRM driver.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The am53c974 is a re-implementation of the tmscsim driver,
and provides the same functionality.
So remove the tmscsim driver and make am53c974 an alias to tmscsim.
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Update MAINTAINERS list and copyright information for megaraid_sas driver.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm using the new Open Source Group address for my upstream work.
While the other email is still valid, it is better for me to receive
patches via the new address.
So, replace it everywhere inside MAINTAINERS.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* Add early debugging support using SCIF(A)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O/9v
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc4-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Fourth Round of Renesas ARM Based SoC Updates for v3.19" from Simon Horman:
* Add early debugging support using SCIF(A)
* tag 'renesas-soc4-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Add early debugging support using SCIF(A)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some distributions carry an "old" format of overlayfs while mainline has a
"new" format.
The distros will possibly want to keep the old overlayfs alongside the new
for compatibility reasons.
To make it possible to differentiate the two versions change the name of
the new one from "overlayfs" to "overlay".
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Reported-by: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Andy Whitcroft <apw@canonical.com>
The GISB bus arbiter driver is relevant for BCM7xxx (brcmstb) platforms,
add an entry to cover this file.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add Gregory Fong and myself as maintainers for the brcmstb platform
along with Brian Norris and Marc Carino.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use kernel.org account instead of samsung.com and cleanup for Samsung
s3c, s5p and exynos SoCs.
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- fixes following legacy board removal
- removal of an unused config option CONFIG_MACH_SAMA5_DT
- move of some header files out of include/mach directory
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUZOvPAAoJEAf03oE53VmQlLMH/Aq/q9FYWyiZqq+DHccUuMvt
IJG2LjTabKb7ihHbsrwaF6kqddISeF4vrBgIoNhNxqfD836MuG5vBpGR1iTXyfqF
q/s/CI6Zmw3KWxCTUJSE8ix8Y6KA5vdI84D4dLorjlYhmFj0xXrteSooMlJ0t9uJ
d8o5gOhaL0nQnhdJ950MsSVopsFzjJ0nzxr0PqsVGx6/DJRB+CyKi9e7419B+Vie
phULLFux3Ai4m7eOHmFxc8vBFwQwSPam2nBiqgFgT1kKDY1igzjwk8PGv1fkLlIk
llBzCQsuXnnScV2auDF7UOEOZHue+eMPajYd+iZkjy5khkTYbdLyz5eW6gZiRdw=
=yqzO
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/cleanup
Pull "Second batch of cleanup/SoC for 3.19" from Nicolas Ferre:
- fixes following legacy board removal
- removal of an unused config option CONFIG_MACH_SAMA5_DT
- move of some header files out of include/mach directory
* tag 'at91-cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: move sdramc/ddrsdr header to include/soc/at91
ARM: at91: remove CONFIG_MACH_SAMA5_DT
ARM: at91: remove unused CONFIG_ARCH_AT91SAM9G45 option
ARM: at91: remove useless init_time for DT-only SoCs
ARM: at91: fix build breakage due to legacy board removals
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Broadcom Cygnus SoC MAINTAINERS updates" from Florian Fainelli:
This pull request contains the MAINTAINERS update to add the Broadcom Cygnus
SoC platform files, Device Tree sources and clock drivers.
* tag 'arm-soc/for-3.19/cygnus-maintainers-v2' of http://github.com/brcm/linux:
MAINTAINERS: Entry for Cygnus/iproc arm architecture
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
KVM for ia64 has been marked as broken not just once, but twice even,
and the last patch from the maintainer is now roughly 5 years old.
Time for it to rest in peace.
Acked-by: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Given the preceding changes to atari_NCR5380.c, this patch should not change
behaviour of the sun3_scsi and sun3_scsi_vme modules.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add serial port debug macros for the SCIF(A) serial ports.
This includes all supported shmobile SoCs, except for EMEV2.
The configuration logic (both Kconfig and #ifdef) is more complicated than
one would expect, for several reasons:
1. Not all SoCs have the same serial devices, and they're not always
at the same addresses.
2. There are two different types: SCIF and SCIFA. Fortunately they can
easily be distinguished by physical address.
3. Not all boards use the same serial port for the console.
The defaults correspond to the boards that are supported in
mainline. If you want to use a different serial port, just change
the value of CONFIG_DEBUG_UART_PHYS, and the rest will auto-adapt.
4. debug_ll_io_init() maps the SCIF(A) registers to a fixed virtual
address. 0xfdxxxxxx was chosen, as it should lie below VMALLOC_END
= 0xff000000, and must not conflict with the 2 MiB reserved region
at PCI_IO_VIRT_BASE = 0xfee00000.
- On SoCs not using the legacy machine_desc.map_io(),
debug_ll_io_init() is called by the ARM core code.
- On SoCs using the legacy machine_desc.map_io(),
debug_ll_io_init() must be called explicitly. Calls are added
for r8a7740, r8a7779, sh7372, and sh73a0.
This was derived from the r8a7790 version by Laurent Pinchart.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Another small set of fixes:
- Some DT compatible typo fixes
- irq setup fix dealing with irq storms on orion
- i2c quirk generalization for mvebu
- A handful of smaller fixes for OMAP
- A couple of added file patterns for OMAP entries in MAINTAINERS
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0RR/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another small set of fixes:
- some DT compatible typo fixes
- irq setup fix dealing with irq storms on orion
- i2c quirk generalization for mvebu
- a handful of smaller fixes for OMAP
- a couple of added file patterns for OMAP entries in MAINTAINERS"
* tag 'armsoc-for-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: at91/dt: Fix sama5d3x typos
pinctrl: dra: dt-bindings: Fix output pull up/down
MAINTAINERS: Update entry for omap related .dts files to cover new SoCs
MAINTAINERS: add more files under OMAP SUPPORT
ARM: dts: AM437x-SK-EVM: Fix DCDC3 voltage
ARM: dts: AM437x-GP-EVM: Fix DCDC3 voltage
ARM: dts: AM43x-EPOS-EVM: Fix DCDC3 voltage
ARM: dts: am335x-evm: Fix 5th NAND partition's name
ARM: orion: Fix for certain sequence of request_irq can cause irq storm
ARM: mvebu: armada xp: Generalize use of i2c quirk
MAINTAINERS file to avoid missing PMIC and SoC related patches:
- Fix random hangs on am437x because of incorrect default
value for the DDR regulator
- Fix wrong partition name for NAND on am335x-evm
- Fix wrong pinctrl defines for dra7xx
- Update maintainers entries for PMICs and SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YQGC
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-against-v3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.18-rc4" from Tony Lindgren:
Few omap fixes for hangs and wrong pinctrl defines, and update
MAINTAINERS file to avoid missing PMIC and SoC related patches:
- Fix random hangs on am437x because of incorrect default
value for the DDR regulator
- Fix wrong partition name for NAND on am335x-evm
- Fix wrong pinctrl defines for dra7xx
- Update maintainers entries for PMICs and SoCs
* tag 'omap-fixes-against-v3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
pinctrl: dra: dt-bindings: Fix output pull up/down
MAINTAINERS: Update entry for omap related .dts files to cover new SoCs
MAINTAINERS: add more files under OMAP SUPPORT
ARM: dts: AM437x-SK-EVM: Fix DCDC3 voltage
ARM: dts: AM437x-GP-EVM: Fix DCDC3 voltage
ARM: dts: AM43x-EPOS-EVM: Fix DCDC3 voltage
ARM: dts: am335x-evm: Fix 5th NAND partition's name
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a set of six fixes and a MAINTAINER update. The fixes are two
multipath (one in Test Unit Ready handling for the path checkers and one in
the section of code that sends a start unit after failover; both of these were
perturbed by the scsi-mq update), a CD-ROM door locking fix that was likewise
introduced by scsi-mq and three driver fixes for a previous code update in
cxgb4i, megaraid_sas and bnx2fc.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJUaM30AAoJEDeqqVYsXL0MxxAIAI1JuPItr4FZCzTSx1Z/XzCu
KVIejPPbwi/uV0MYmHxxeb9T+gPOw4ssZJFHEzzE/z1CmBvwhRzaxE9GBf5IPJD0
uMl+2e4DwRxTa/7T5I3psxlXSM3asx8vER+5qL3qpveu14mablHUjeLAvwuavITs
IVCGbp8g8Mi+PTXFolUSDRj9qY59lvTSOcvbcO7m915/n4ne3M9YHWwG7CLvu+42
7VoN3HAPWE+DZg+Jnf4RyOULrh7BNwCOsrkD/gVe7DX8lxbBYv/H1iAApujFuSbk
AKwO1+NWszM4OnXdYa7O+8nsYGfmRen5krrmU66i7F4m/Z88zsnUa8jylMC7HcE=
=QjUD
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of six fixes and a MAINTAINER update.
The fixes are two multipath (one in Test Unit Ready handling for the
path checkers and one in the section of code that sends a start unit
after failover; both of these were perturbed by the scsi-mq update), a
CD-ROM door locking fix that was likewise introduced by scsi-mq and
three driver fixes for a previous code update in cxgb4i, megaraid_sas
and bnx2fc"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
bnx2fc: fix tgt spinlock locking
megaraid_sas: fix bug in handling return value of pci_enable_msix_range()
cxgb4i: send abort_rpl correctly
cxgbi: add maintainer for cxgb3i/cxgb4i
scsi: TUR path is down after adapter gets reset with multipath
scsi: call device handler for failed TUR command
scsi: only re-lock door after EH on devices that were reset
During the discussion about adding clock handling code to simplefb, it became
clear that simplefb currently does not have an active maintainer.
I've discussed this with Stephen Warren <swarren@wwwdotorg.org>, the original
author of simplefb, and with his permisson I'm picking up maintainership of
simplefb.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Files under include/linux/iio were not reported as part of the IIO
subsystem.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reported-by: Cristina Ciocan <cristina.ciocan@intel.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
EZchip Semiconductor closed the acquisition of Tilera Corp
last week, and tilera.com email addresses are now ezchip.com.
http://www.ezchip.com/pr_141106.htm
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Move the (DDR) SDRAM controller headers to include/soc/at91 to remove the
dependency on mach/ headers from the at91-reset driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Needed due to some important regression fixes at RC core.
* commit 'v3.18-rc4': (587 commits)
Linux 3.18-rc4
ARM: dts: zynq: Enable PL clocks for Parallella
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
USB: Update default usb-storage delay_use value in kernel-parameters.txt
sysfs: driver core: Fix glue dir race condition by gdp_mutex
MIPS: Fix build with binutils 2.24.51+
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
USB: cdc-acm: add quirk for control-line state requests
tty: Fix pty master poll() after slave closes v2
MIPS: R3000: Fix debug output for Virtual page number
...
Conflicts:
drivers/media/rc/rc-main.c
DRA7(including AM5x) and AM47x series are handled under OMAP umbrella.
These SoC support and dts have been added since 3.14 kernel and Pull
requests for these have come in from OMAP till date.
So just ensure that get_maintainers can pick up this list as well.
Cc: linux-omap@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Benoît Cousson <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These files are very important to the healt
of the OMAP architecture, specially when it
comes to PM support which currently we have
working for at least OMAP3 and we'd like
to know about any changes being made to our
PMICs and IRQ controllers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
John W. Linville says:
====================
pull request: wireless-next 2014-11-07
Please pull this batch of updates intended for the 3.19 stream!
For the mac80211 bits, Johannes says:
"This relatively large batch of changes is comprised of the following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions"
For the Bluetooth bits, Johan says:
"Here's the first bluetooth-next pull request for 3.19. The vast majority
of patches are for ieee802154 from Alexander Aring with various fixes
and cleanups. There are also several LE/SMP fixes as well as improved
support for handling LE devices that have lost their pairing information
(the patches from Alfonso). Jukka provides a couple of stability fixes
for 6lowpan and Szymon conformance fixes for RFCOMM. For the HCI drivers
we have one new USB ID for an Acer controller as well as a reset
handling fix for H5."
For the Atheros bits, Kalle says:
"Major changes are:
o ethtool support (Ben)
o print dev string prefix with debug hex buffers dump (Michal)
o debugfs file to read calibration data from the firmware verification
purposes (me)
o fix fw_stats debugfs file, now results are more reliable (Michal)
o firmware crash counters via debugfs (Ben&me)
o various tracing points to debug firmware (Rajkumar)
o make it possible to provide firmware calibration data via a file (me)
And we have quite a lot of smaller fixes and clean up."
For the iwlwifi bits, Emmanuel says:
"The big new thing here is netdetect which allows the
firmware to wake up the platform when a specific network
is detected. Along with that I have fixes for d3 operation.
The usual amount of rate scaling stuff - we now support STBC.
The other commit that stands out is Johannes's work on
devcoredump. He basically starts to use the standard
infrastructure he built."
Along with that are the usual sort of updates and such for ath9k,
brcmfmac, wil6210, and a handful of other bits here and there...
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Another quiet week:
- A fix to silence edma probe error on non-supported platforms from Arnd
- A fix to enable the PL clock for Parallella, to make mainline usable with
the SDK.
- A somewhat verbose fix for the PLL clock tree on VF610
- Enabling of SD/MMC on one of the VF610-based boards (for testing)
- A fix for i.MX where CONFIG_SPI used to be implicitly enabled and now needs
to be added to the defconfig instead
- Another maintainer added for bcm2835: Lee Jones
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bOlr
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another quiet week:
- a fix to silence edma probe error on non-supported platforms from
Arnd
- a fix to enable the PL clock for Parallella, to make mainline
usable with the SDK.
- a somewhat verbose fix for the PLL clock tree on VF610
- enabling of SD/MMC on one of the VF610-based boards (for testing)
- a fix for i.MX where CONFIG_SPI used to be implicitly enabled and
now needs to be added to the defconfig instead
- another maintainer added for bcm2835: Lee Jones"
* tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: zynq: Enable PL clocks for Parallella
dma: edma: move device registration to platform code
ARM: dts: vf610: add SD node to cosmic dts
MAINTAINERS: update bcm2835 entry
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
Here are some USB fixes for 3.18-rc4.
Just a bunch of little fixes resolving reported issues and new device ids for
existing drivers. Full details are in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlReZzgACgkQMUfUDdst+ylTIgCdG8L088p1OqgEdcL+J0ceYS51
PQAAn3O4t962htLmX0XuQmfMWTyBqn11
=3auS
-----END PGP SIGNATURE-----
Merge tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.18-rc4.
Just a bunch of little fixes resolving reported issues and new device
ids for existing drivers. Full details are in the shortlog"
* tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: Update default usb-storage delay_use value in kernel-parameters.txt
USB: cdc-acm: add quirk for control-line state requests
phy: omap-usb2: Enable runtime PM of omap-usb2 phy properly
USB: storage: Fix timeout in usb_stor_euscsi_init() and usb_stor_huawei_e220_init()
USB: cdc-acm: only raise DTR on transitions from B0
Revert "storage: Replace magic number with define in usb_stor_euscsi_init()"
usb: core: notify disconnection when core detects disconnect
usb: core: need to call usb_phy_notify_connect after device setup
uas: Add US_FL_NO_ATA_1X quirk for 2 more Seagate models
xhci: no switching back on non-ULT Haswell
USB: quirks: enable device-qualifier quirk for yet another Elan touchscreen
USB: quirks: enable device-qualifier quirk for another Elan touchscreen
MAINTAINERS: Remove duplicate entry for usbip driver
usb: storage: fix build warnings !CONFIG_PM
usb: Remove references to non-existent PLAT_S5P symbol
uas: Add NO_ATA_1X for VIA VL711 devices
xhci: Disable streams on Asmedia 1042 xhci controllers
USB: HWA: fix a warning message
uas: Add US_FL_NO_ATA_1X quirk for 1 more Seagate model
usb-storage: handle a skipped data phase
...
This patch adds the new userspace header for nl802154. We don't place
this header in include/uapi now. This header could be modified in the
next time.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
