The AVC protocol uses the same command for tuning and PID filtering and
since dvb-core uses a software zigzagging to do automatic retuning this
could cause all PID filters to be cleared. PID filter information is
now included in all DSD commands to the card.
Background:
There is a problem in the firedtv driver that causes recordings to stop
if the SW zigzag algorithm in dvb-core kicks in with a retune after the
application has set up the PID filters. Since tuning and setting PID
filters uses the same AVC command (DSD) and only the replace subfunction
is supported by the card, it is not possible to do a retune without
setting the PID filters. This means that the PID filtering has to be
sent in each tune.
This problem applies to C and T cards since S and S2 cards tune using a
vendor specific command. The patch corrects the problem by sending the
PID list in each tune. I have tested it on my T card with a good
result.
How to trigger problem: Zap to a channel and output AV to a file, e.g.
"tzap -c channels.conf SVT1 -r -o SVT1.ts". After a short while, pull
the antenna cable from the card. The lock on the channel will disappear
and the TS file will stop increasing in size. Wait a couple of seconds.
Replug the cable again. You will get a lock on the channel again, but
the TS file will never increase in size agains sinze no PIDS are
filtered.
Tested with kaffeine with DVB-T and DVB-C: Fixes retuning after antenna
was plugged out and back in with DVB-T. Does not fix this with DVB-C,
but also doesn't regress on DVB-C.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Attached is a patch which fixes tuning to low frequency channels with
stb0899+tda8261 cards like the KNC TV-Station DVB-S2.
The cause of the issue was a broken if construct, which should have been
an if/else if, so that the setting for the lowest matching frequency is
applied.
Without this patch for example tuning to "arte" on Astra 19.2, 10744MHz
SR22000 failed most times and when it failed the communication between
driver and tda8261 was completely broken.
This problem disappears with the attached patch.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new USB ID (1b80:e400) for KWorld PlusTV Dual DVB-T Stick (DVB-T 399U).
The model number on the devices sticker label is "KW-DVB-T 399UR".
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These changes were a direct result of using a semantic patch
More information can be found at http://www.emn.fr/x-info/coccinelle/
[mchehab@redhat.com: fix a merge conflict]
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems from other code that it is the dst_type field rather than the
type_flags field that contains values of the form DST_TYPE_IS...
The type_flags field contains values of the form DST_TYPE_HAS...
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ struct dst_state E; @@
(
*E.type_flags ==
\( DST_TYPE_IS_SAT\|DST_TYPE_IS_TERR\|DST_TYPE_IS_CABLE\|DST_TYPE_IS_ATSC \)
|
*E.type_flags !=
\( DST_TYPE_IS_SAT\|DST_TYPE_IS_TERR\|DST_TYPE_IS_CABLE\|DST_TYPE_IS_ATSC \)
)
// </smpl>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for Humax/Coex DVB-T USB Stick 2.0 High Speed
which is a very popular tuner sold in Vietnam.
Tested with at least 3 tuners.
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Pham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The changeset 0b17d0ed that aded ASUSTeK P7131 Analog were using
7 spaces instead of tab, probably due to some bad cut-and-paste.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On VIDEO_M52790 and USB_GSPCA_SN9C20X, instead of tab, it were
using 7 whitespaces at the beginning, probably due to some
cut-and-paste trouble.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch solves problem of missed keystrokes on some remote controls,
as reported on http://bugzilla.kernel.org/show_bug.cgi?id=9637 .
Signed-off-by: Andrzej Hajda <andrzej.hajda@wp.pl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card includes Intel ce5039(Zarlink zl10039) tuner
and Intel ce6313 (Zarlink zl10313) demod.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code from Jan D. Louw with some minor changes.
http://article.gmane.org/gmane.linux.drivers.dvb/38163
Tested with TeVii S630 DVB-S USB card by me (Igor)
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Robert P.J. Day for finding this.
Thanks-to: Robert P.J. Day <rpjday@crashcourse.ca>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the remote control that comes with the Cinergy Hybrid T USB XS
Thanks to Jelle de Jong for providing sample hardware to test with.
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I updated and simplyfied patch from Zbynek Hrabovsky for recent kernel.
It enables autodetection of card, sound in analog TV , sound in FM radio
and switching between antenna and cable RF input. Radio tuner still
doesn't work, I don't even know how it works. Some guys wrote me that FM
radio works with TV tuner used instead of radio part (symlink video0 ->
radio0).
Cc: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Vlastimil Labsky <vlasta.labsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
do_div requires an u64 as the first argument, not a s64.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use unified lgs8gxx frontend instead of reverse engineered lgs8gl5 frontend.
After this patch, lgs8gl5 frontend could be mark as deprecated.
Future development should base on unified lgs8gxx frontend.
Signed-off-by: David T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Error handling code following a kmalloc should free the allocated data.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We have support for radio on saa7133/35/31e cards with tda8290/8275(a)
and 5.5MHz ceramic filter on the bridge chips since a while.
It was previously not tested, if this card supports it too, but the old
"ghost" radio with wrong filters doesn't work anymore.
Thanks go to Pham Thanh Nam and Laszlo Kustan for reporting it working
on that input.
Signed-off-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Define correct tuner in config. Radio now works fine
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The structure and comments of the I2C part have been adopted to fit to the
USB part.
Some additional cleanups and precisements have been made to the version
detection and checking functionality to clearly separate HW/SW/FW version.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch supports i2c interface of si470x. The i2c specific part
exists in radio-si470x-i2c.c file and the common part uses
radio-si470x-common.c file. The '#if defined' is inserted inevitably
because of parts used only si470x usb in the common file.
The current driver version doesn't support the RDS.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The si470x_disconnect_check is function to check disconnect state of
radio in common file. The function is implemented in each interface
file.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is for using dev_* macro instead of printk.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is a preceding work to add the i2c interface of si470x.
The si470x directory includes a common file and usb specific file and
header file.
The part unrelated with usb interface and i2c interface exists in
radio-si470x-common.c file, and The usb specific part exists in
radio-si470x-usb.c file.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
[tobias.lorenz@gmx.net: Small changes, due to new include "linux/smp_lock.h"]
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for the STK7700D USB-DVB-Device.
lsusb identifies it as:
idVendor 0x1164 YUAN High-Tech Development Co., Ltd
idProduct 0x1efc
iProduct 2 STK7700D
The device is build into a Samsung R55-T5500 notebook.
Signed-off-by: Pete Hildebrandt <send2ph@googlemail.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Restructure the UVC descriptors parsing code to handle multiple streaming
interfaces. The driver now creates a uvc_video_chain instance for each chain
detected in the UVC control interface descriptors, and tries to register one
video device per streaming endpoint.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a first step towards multiple streaming interfaces support, reorganize the
driver's data structures to cleanly separate video control and video streaming
data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 API (chapter 1.5) states that:
Drivers must implement all input ioctls when the device has one
or more inputs, all output ioctls when the device has one or more outputs.
When the device has any audio inputs or outputs the driver must set the
V4L2_CAP_AUDIO flag in the struct v4l2_capability returned by the
VIDIOC_QUERYCAP ioctl.
So, devices without audio input should return -EINVAL.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are many lock imbalances in this driver. Fix all found.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There seems to be one superfluos unlock in a poll function. Remove it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The irq handler will touch memory. Even in the error case some URBs may
complete. Thus no memory must be kfreed before all URBs are killed.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for Zilog Z8F0811 IR transceiver chips on
CX2341[68] based boards to ir-kbd-i2c for both the old i2c binding model
and the new i2c binding model.
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add support to the cx18 driver for setting up the
Z8F0811/Hauppauge IR Tx/Rx chip with the i2c binding model in newer
kernels.
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch augments the init data passed by bridge drivers to
ir-kbd-i2c, so that the ir_type can be set explicitly, and so
ir-kbd-i2c internal get_key functions can be reused without
requiring symbols from ir-kbd-i2c in the bridge driver.
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Functions which are referenced by their address can't be inlined by
definition.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The au0828-dvb driver uses bulk usb transfers for digital transport,
but the debug reports, "iso xfer already running!\n".
Fix this to report bulk instead of isoc.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This prevents a loop if a permanent error occurs in usb_set_interface().
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
