Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/max77620-regulator.o
text data bss dec hex filename
4811 6992 0 11803 2e1b regulator/max77620-regulator.o
File size after: drivers/regulator/max77620-regulator.o
text data bss dec hex filename
5075 6720 0 11795 2e13 regulator/max77620-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding support to configure regulator POK mapping bit
to control nRST_IO and GPIO1 POK function.
In tegra based platform which uses MAX20024 pmic, when
some of regulators are configured FPS_NONE(flexible power sequencer)
causes PMIC GPIO1 to go low which lead to various other rails turning off,
to avoid this MPOK bit of those regulators need to be set to 0
so that PMIC GPIO1 will not go low.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
max77620_reuglator_pdata structure variable reg_idata
is not used anywhere in the regulator driver, so removing it.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SD4 regulator is not registered with regulator core
framework in probe as there is no support in MAX77620 PMIC,
removing SD4 entry from MAX77620 regulator information list
and checking for valid regulator information data before
configuring FPS source and FPS power up/down period to avoid
NULL pointer exception if regulator not registered with core.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Maxim advertised the ramp rate of the rail with some recommended
design specification like output capacitance of rail should be
2.2uF. This make sure that current change in the rail is within
maximum current limit and hence meet the advertised ramp rate.
If there is variation in design which causes the rail current to
change more that maximum current limit then device applies the
current limit. In this case, ramp rate is different than advertised
ramp rate.
Add device specific settings for ramp rate which need to be configure
on device register when measure ramp rate on platform is deviated from
advertised ramp rate. In this case, all delay time calculation for
voltage change is done with measured ramp rate and device ramp rate
is used for configuring the device register.
If measured ramp rate in the platform is same as advertised ramp rate
then regulator-ramp-delay is used for the device register configuration
and ramp time calculation for voltage change.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator ops callback for configuration of active-discharge
and provide necessarily information via regulator descriptor.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These fields are never used and not required at all, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MAXIM Semiconductor's PMIC, MAX77620 and MAX20024 have the
multiple DCDC and LDOs. This supplies the power to different
components of the system.
Also these rails has configuration for ramp time, flexible
power sequence, slew rate etc.
Add regulator driver to access these rails via regulator APIs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
