Add SD Card support to the kfr2r09 board using the
sh_mobile_sdhi driver hooked up to SDHI0 and yc304.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SD Card support to the se7724 board using the
sh_mobile_sdhi driver hooked up to SDHI0 and CN7.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the AP325 board to use sh_mobile_sdhi for the
SD Card connected to CN3 instead of mmc_spi.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the Migo-R board to use sh_mobile_sdhi for the
SD Card connected to CN9 instead of mmc_spi.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SUPERH to the Kconfig dependencies for tmio_mmc.
This change allows us to drive the SDHI hardware blocks
found in SuperH Mobile with tmio_mmc.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds an MFD driver for the SuperH Mobile SDHI
hardware block. At this point the driver simply wraps the
tmio-mmc driver with some clock code. In the future this
driver is the place to put SDHI specific hotplug code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves the current dma_alloc/free_coherent() calls to a generic
variant and plugs them in for the nommu default. Other variants can
override the defaults in the dma mapping ops directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the past these were simply wrapping to barrier() which was sufficient
on SH SMP platforms predating SH-4A. Unfortunately due to ll/sc semantics
an explicit synco is needed in these cases, which is sorted for us by
just switching these over to smp_mb(). smp_mb() also has the benefit of
being wrapped to barrier() in the UP and non-SH4A cases, so old behaviour
is maintained for those parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SCIF2 and the FPU exceptions happen to share vector numbers, one in
EXPEVT and the other in INTEVT. This is a violation of the interface and
should have never made it in to silicon. On top of that, the demux hack
that was added for special dispatch is rather error prone, and introduces
more problems than it solves. Kill all of it off, and just refuse to deal
with SCIF2 outright.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This simplifies the irqflags support by switching over to the asm-generic
version. The necessary support functions are brought out-of-line for both
SHcompact and SHmedia instruction sets.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code was added for some ancient SH-4 solution engines with peculiar
boot ROMs that did silly things to the UBC MSTP bits. None of these have
been in the wild for years, and these days the clock framework wraps up
the MSTP bits, meaning that the UBC code is one of the few interfaces
that is stomping MSTP bits underneath the clock framework. At this point
the risks far outweigh any benefit this code provided, so just kill it
off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables SCHED_MC support for SH-X3 multi-cores. Presently this is
just a simple wrapper around the possible map, but this allows for
tying in support for some of the more exotic NUMA clusters where we can
actually do something with the topology.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the case where need_resched() is set in between the cpu_idle() and
pm_idle() calls we were missing an else case for just re-enabling local
IRQs and bailing out. This was noticed by the irqs_disabled() warning,
even though IRQs were being re-enabled elsewhere.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the x86 change and moves check_pgt_cache() up under the
!need_resched() tight loop, rather than simply calling in to it when
exiting idle.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This does a bit of chainsawing of the idle loop code to get light sleep
working on SMP. Previously this was forcing secondary CPUs in to sleep
mode with them not coming back if they didn't have their own local
timers. Given that we use clockevents broadcasting by default, the CPU
managing the clockevents can't have IRQs disabled before entering its
sleep state.
This unfortunately leaves us with the age-old need_resched() race in
between local_irq_enable() and cpu_sleep(), but at present this is
unavoidable. After some more experimentation it may be possible to layer
on SR.BL bit manipulation over top of this scheme to inhibit the race
condition, but given the current potential for missing wakeups, this is
left as a future exercise.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the secondary CPUs are forced in to light sleep mode, but we were
missing the same initialization for the boot CPU. This resulted in
inconsistent sleep modes depending on which CPU we were on, confusing the
idle loop when not polling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The open function got the BKL via the big push down. Replace it by
preempt_enable/disable as this is sufficient for an UP machine.
The ioctl can be unlocked because there is no functionality which
requires serialization. The usage by multiple callers is broken with
and without the BKL due to the local static variable addr.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add code to handle the cache disabled case. Fixes breakage introduced by
37443ef3f0 ("sh: Migrate SH-4 cacheflush
ops to function pointers."). Without this patch configuring caches off
with CONFIG_CACHE_OFF=y makes kfr2r09 and migo-r lock up in fbdev
deferred io or early user space.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently The SH-4 cache flushing code uses flush_cache_4096() for most
of the real flushing work, which breaks down to a fixed 4096 unroll and
increment. Not only is this sub-optimal for larger page sizes, it's also
uncovered a bug in sh4_flush_dcache_page() when large page sizes are used
and we have no cache aliases -- resulting in only a part of the page's
D-cache lines being written back.
Signed-off-by: Valentin Sitdikov <valentin.sitdikov@siemens.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The destination keyring specified to request_key() and co. is made available to
the process that instantiates the key (the slave process started by
/sbin/request-key typically). This is passed in the request_key_auth struct as
the dest_keyring member.
keyctl_instantiate_key and keyctl_negate_key() call get_instantiation_keyring()
to get the keyring to attach the newly constructed key to at the end of
instantiation. This may be given a specific keyring into which a link will be
made later, or it may be asked to find the keyring passed to request_key(). In
the former case, it returns a keyring with the refcount incremented by
lookup_user_key(); in the latter case, it returns the keyring from the
request_key_auth struct - and does _not_ increment the refcount.
The latter case will eventually result in an oops when the keyring prematurely
runs out of references and gets destroyed. The effect may take some time to
show up as the key is destroyed lazily.
To fix this, the keyring returned by get_instantiation_keyring() must always
have its refcount incremented, no matter where it comes from.
This can be tested by setting /etc/request-key.conf to:
#OP TYPE DESCRIPTION CALLOUT INFO PROGRAM ARG1 ARG2 ARG3 ...
#====== ======= =============== =============== ===============================
create * test:* * |/bin/false %u %g %d %{user:_display}
negate * * * /bin/keyctl negate %k 10 @u
and then doing:
keyctl add user _display aaaaaaaa @u
while keyctl request2 user test:x test:x @u &&
keyctl list @u;
do
keyctl request2 user test:x test:x @u;
sleep 31;
keyctl list @u;
done
which will oops eventually. Changing the negate line to have @u rather than
%S at the end is important as that forces the latter case by passing a special
keyring ID rather than an actual keyring ID.
Reported-by: Alexander Zangerl <az@bond.edu.au>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Alexander Zangerl <az@bond.edu.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pci: Fix MODPOST warning
powerpc/oprofile: Add ppc750 CL as supported by oprofile
powerpc: warning: allocated section `.data_nosave' not in segment
powerpc/kgdb: Fix build failure caused by "kgdb.c: unused variable 'acc'"
powerpc: Fix hypervisor TLB batching
powerpc/mm: Fix hang accessing top of vmalloc space
powerpc: Fix memory leak in axon_msi.c
powerpc/pmac: Fix issues with sleep on some powerbooks
powerpc64/ftrace: use PACA to retrieve TOC in mod_return_to_handler
powerpc/ftrace: show real return addresses in modules
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI button: don't try to use a non-existent lid device
ACPI: video: Loosen strictness of video bus detection code
eeepc-laptop: Prevent a panic when disabling RT2860 wireless when associated
eeepc-laptop: Properly annote eeepc_enable_camera().
ACPI / PCI: Fix NULL pointer dereference in acpi_get_pci_dev() (rev. 2)
fujitsu-laptop: address missed led-class ifdef fixup
ACPI: Kconfig, fix proc aggregator text
ACPI: add AC/DC notifier
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP2xxx clock: set up clockdomain pointer in struct clk
OMAP: Fix race condition with autodeps
omap: McBSP: Fix incorrect receiver stop in omap_mcbsp_stop
omap: Initialization of SDRC params on Zoom2
omap: RX-51: Drop I2C-1 speed to 2200
omap: SDMA: Fixing bug in omap_dma_set_global_params()
omap: CONFIG_ISP1301_OMAP redefined in Beagle defconfig
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: always pin metadata in discard mode
Btrfs: enable discard support
Btrfs: add -o discard option
Btrfs: properly wait log writers during log sync
Btrfs: fix possible ENOSPC problems with truncate
Btrfs: fix btrfs acl #ifdef checks
Btrfs: streamline tree-log btree block writeout
Btrfs: avoid tree log commit when there are no changes
Btrfs: only write one super copy during fsync
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
sysfs: Allow sysfs_notify_dirent to be called from interrupt context.
sysfs: Allow sysfs_move_dir(..., NULL) again.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: gadget: Fix EEM driver comments and VID/PID
usb-storage: Workaround devices with bogus sense size
USB: ehci: Fix IST boundary checking interval math.
USB: option: Support for AIRPLUS MCD650 Datacard
USB: whci-hcd: always do an update after processing a halted qTD
USB: whci-hcd: handle early deletion of endpoints
USB: wusb: don't use the stack to read security descriptor
USB: rename Documentation/ABI/.../sysfs-class-usb_host
* branch 'tty-fixes'
tty: use the new 'flush_delayed_work()' helper to do ldisc flush
workqueue: add 'flush_delayed_work()' to run and wait for delayed work
tty: Make flush_to_ldisc() locking more robust
The 2.6.32 merge window brought a number of changes to the flexible array
API; this patch updates the documentation to match the new state of
affairs.
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This reverts commit e9a63a4e55.
This breaks older binutils, where sink-less asserts are broken.
See this commit for further details:
d2ba8b2: x86: Fix assert syntax in vmlinux.lds.S
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <4AD6523D.5030909@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
vmxnet3 uses in_dev* interfaces so it should depend on INET.
Also fix so that the driver builds when CONFIG_PCI_MSI is disabled.
vmxnet3_drv.c:(.text+0x2a88cb): undefined reference to `in_dev_finish_destroy'
drivers/net/vmxnet3/vmxnet3_drv.c:1335: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:1384: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:2137: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:2138: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bhavesh davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
