All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return type of usbhsp_setup_pipecfg() was u16 but it was returning
a negative value (-EINVAL). Lets have an additional argument which will
have pipecfg and just return the status (success or error) as the return
from the function.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since usbhsg_dma_map_ctrl() needs DMA device structure in the near future,
this patch changes arguments of dma_map_ctrl() to give such data.
(This patch is only change the argument.)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since Some SoCs (e.g. R-Car Gen2) don't have the CSSTS bit in the
pipectrl registers ({DCP,PIPEn}CTR) because such SoCs have peripheral
mode only. So, this driver should not check the CSSTS bit if peripheral
mode is running.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The current code has info->bufnmb_last to calculate the BUFNMB bits of
PIPEBUF register. However, since the bufnmb_last is initialized in
the usbhs_pipe_init() only, this driver is possible to set unexpected
value to the register if usb_ep_{enable,disable}() are called many times.
So, this patch modifies the pipe configuration via struct
renesas_usbhs_driver_param to simplify the code. Also this patch changes:
- a double buffer configuration
- isochronous buffer size from 512 to 1024
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some Renesas SoCs have the USB-DMAC. It is able to terminate transfers
when a short packet is received, even if less bytes than the transfer
counter size have been received. Also, it is able to send a short
packet even if the packet size is not multiples of 8bytes.
Since the previous code has used the interruption of USBHS controller
when receiving packets even if this driver has used a dmac, a lot of
interruptions has happened. This patch will reduce such interruptions.
This patch allows to use the USB-DMAC on R-Car H2 and M2.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the DCPCTR doesn't have the ACLRM bit, the usbus_pipe_clear()
should not call the usbhsp_pipectrl_set() with ACLRM.
So, this patch fixes this issue to add the usbhs_fifo_clear_dcp()
in fifo.c because the controller needs the CFIFO to clear the
the DCP PIPE.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some gadget drivers will call usb_ep_queue() more than once before
the first queue doesn't finish. However, this driver didn't handle
it correctly. So, this patch fixes the behavior of some
usbhs_pkt_handle using the "running" flag. Otherwise, the oops below
happens if we use g_ncm driver and when the "iperf -u -c host -b 200M"
is running.
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 80000007 [#1] SMP ARM
Modules linked in: usb_f_ncm g_ncm libcomposite u_ether
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 3.17.0-rc1-00008-g8b2be8a-dirty #20
task: c051c7e0 ti: c0512000 task.ti: c0512000
PC is at 0x0
LR is at usbhsf_pkt_handler+0xa8/0x114
pc : [<00000000>] lr : [<c0278fb4>] psr: 60000193
sp : c0513ce8 ip : c0513c58 fp : c0513d24
r10: 00000001 r9 : 00000193 r8 : eebec4a0
r7 : eebec410 r6 : eebe0c6c r5 : 00000000 r4 : ee4a2774
r3 : 00000000 r2 : ee251e00 r1 : c0513cf4 r0 : ee4a2774
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue that the renesas_usbhs driver in gadget mode
cannot work correctly even if I disabled DMAC of the driver when I used
the g_zero driver and the testusb tool.
When a usb cable is re-connected, the renesas_usbhs driver calls the
usbhsp_flags_init() (via usbhs_hotplug() --> usbhs_mod_call(start) -->
usbhsg_try_start() --> usbhs_pipe_init()). However, the driver doesn't
call the usbhsp_flags_init() when usbhsg_ep_disable() is called.
So, if a gadget driver calls usb_ep_enable() and usb_ep_disable() again
and again, the renesas_usbhs driver will output the following log:
renesas_usbhs renesas_usbhs: can't get pipe (BULK)
renesas_usbhs renesas_usbhs: wrong recip request
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue that the driver cannot push a new data when
a pipe is re-enabled after the pipe is queued.
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
received data will break if it was bulk pipe and large data size,
because pipe kept BUF PID even though it doesn't have enough buffer.
To avoid this issue, renesas_usbhs can use transfer counter.
Pipe PID will be NAK if it didn't have enough buffer by this patch.
renesas_usbhs has strange address mapping.
Thus, it is difficult to calculate transfer counter setting address.
This patch use fixed table for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A few quoted includes start with a superfluous "./". Clean up those
quoted includes.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is just a minor optimization for the long
if we have on the driver.
When we want to check that one input is true
and the other must be false, the bitwise XOR
operator will achieve that for us.
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
driver has to re-use the limited pipe for each device/endpoint
when it is USB host hub mode, since number of pipe has limitation.
Then, each pipe should care own pipe sequence for next packet.
This patch adds sequence control.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CCPL setting is needed on only mod_gadget.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs can manually set DATA0/DATA1.
This patch is prepare for mod_host support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
transfer done function was registered in struct struct usbhs_pipe_info.
It was good for mod_gadget, but not good for mod_host.
This function move it to struct usbhs_pkt.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
pipe name is usefull function for mod_xxx
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
device select method will be used on mod_host
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was no method to get struct usbhs_priv when
packet transfer done function was called.
This patch allow that callback function receive it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs device needs special bit settings
if it was mod_host and dcp pipe.
This patch support it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
it was possible to get usbhs_mod from usbhs_priv.
this patch remove unneeded parameter.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usbhs_usbreq_get/set_val() functions were in pipe.c file,
but it is irrelevant to pipe.
this patch move it to common.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pipe type check macro will be used in other files.
This patch move local macro to global macro.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current renesas_usbhs pipe accessed DCPMAXP/PIPEMAXP register
to get own maxpacket size every time.
But maxpacket size isn't changed after pipe start,
and register access is too slow.
This patch adds new maxp variable to keep own maxpacket.
And un-used function are removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current usbhs_pipe_malloc() used usb_endpoint_descriptor to
get necessary information.
It was very good for mod_gadget which allocate pipe in runtime,
but is not good for mod_host which allocate pipe in initial timing.
This patch remove usb_endpoint_descriptor from usbhs_pipe_malloc()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sometimes the connection fail happen on renesas_usbhs.
This patch fix it up.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB DMA was installed on "normal DMAC" when SH7724 or older SuperH,
but the "USB-DMAC" was prepared on recent SuperH.
These 2 DMAC have a little bit different behavior.
This patch add DMAEngine code for "normal DMAC",
but it is still using PIO fifo.
The DMA fifo will be formally supported in the future.
You can enable DMA fifo by local fixup
usbhs_fifo_pio_push_handler -> usbhs_fifo_dma_push_handler
usbhs_fifo_pio_pop_handler -> usbhs_fifo_dma_pop_handler
on usbhsg_ep_enable.
This DMAEngine was tested by g_file_storage on SH7724 Ecovec board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
renesas_usbhs has CFIFO which is for PIO transfer,
and D0FIFO/D1FIFO which are for DMA transfer.
The pipe selects one of these fifo when it send/recv data.
But fifo must not be selected to different pipe in same time.
This patch add pipe/fifo link for each other,
and fifo is not selected by another pipe until it is unselected.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On current driver, overall data transfer method was implemented in fifo.c,
but its interrupt which is member of packet queue control
was still in mod_gadget.c.
This patch move it into fifo.c.
By this patch, the packet/fifo control is independent from mod_gadget.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current renesas_usbhs driver is controlling packet queue on mod_gadget.c.
But it has relationship with pipe/fifo, not host/gadget.
So, controlling USB packet queue in pipe.c/fifo.c is
more convenient than in mod_gadget.c.
This patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DMAEngine will be supported to this driver in the future.
Then, both PIO and DMA data transfer method should be supported.
But, the transfer function can returns the result immediately
in PIO version, but it can't in DMA version.
This patch divides data transfer functions into top/bottom half
in preparation for DMAEngine support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current renesas_usbhs has PIO data transfer mode which controls CFIFO.
And it was implemented in pipe.c.
But, fifo control method needs more flexible implementation
to support DMAEngine.
This patch create fifo.c, and it became independent from pipe.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current driver had pipe direction flag
which came from usb_endpoint_dir_in().
It means "input direction" for HOST,
and "out direction" for Gadget.
But driver needs "input direction for pipe".
This patch adds IS_DIR_HOST flags and care
both "input direction for HOST" and "input direction for pipe"
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It was necessary to check pipe condition after disable fifo.
Current driver checked it in a wrong place.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pipe buffer should be cleaned before using it,
but should NOT be cleaned in pipe "prepare" function.
Because the pipe might be working in such timing.
This patch fixup this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Renesas SuperH has USBHS IP which can switch Host / Function.
This driver is designed so that Host / Function may dynamically change.
This patch add usb/renesas_usbhs and common code for SuperH USBHS.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
