In a mixed environment it may be difficult to tell if your hardware
support carrier, if it does not it can always report true. With a new
use_carrier option of 2, we can check both carrier and link status
sequentially, instead of one or the other
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DT bindings for the Ethernet switch found on Microsemi Ocelot platforms.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DT bindings for the Microsemi MII Management Controller found on Microsemi
SoCs
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner R40 SoC has the EMAC controller supported by dwmac-sun8i.
It is named "GMAC", while EMAC refers to the 10/100 Mbps Ethernet
controller supported by sun4i-emac. The controller is the same, but
the R40 has the glue layer controls in the clock control unit (CCU),
with a reduced RX delay chain, and no TX delay chain.
This patch adds the R40 specific bits to the dwmac-sun8i binding.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The syscon property is used to point to the device that holds the glue
layer control register known as the "EMAC (or GMAC) clock register".
We do not need to explicitly list what compatible strings are needed, as
this information is readily available in the user manuals. Also the
"syscon" device type is more of an implementation detail. There are many
ways to access a register not in a device's address range, the syscon
interface being the most generic and unrestricted one.
Simplify the description so that it says what it is supposed to
describe.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The A83T syscon compatible was appended to the syscon compatibles list,
instead of inserted in to preserve the ordering.
Move it to the proper place to keep the list sorted.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clock delay chains found in the glue layer for dwmac-sun8i are only
used with RGMII PHYs. They are not intended for non-RGMII PHYs, such as
MII external PHYs or the internal PHY. Also, a recent SoC has a smaller
range of possible values for the delay chain.
This patch reformats the delay chain section of the device tree binding
to make it clear that the delay chains only apply to RGMII PHYs, and
make it easier to add the R40-specific bits later.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Verify lengths of keys provided by the user is AF_KEY, from Kevin
Easton.
2) Add device ID for BCM89610 PHY. Thanks to Bhadram Varka.
3) Add Spectre guards to some ATM code, courtesy of Gustavo A. R.
Silva.
4) Fix infinite loop in NSH protocol code. To Eric Dumazet we are most
grateful for this fix.
5) Line up /proc/net/netlink headers properly. This fix from YU Bo, we
do appreciate.
6) Use after free in TLS code. Once again we are blessed by the
honorable Eric Dumazet with this fix.
7) Fix regression in TLS code causing stalls on partial TLS records.
This fix is bestowed upon us by Andrew Tomt.
8) Deal with too small MTUs properly in LLC code, another great gift
from Eric Dumazet.
9) Handle cached route flushing properly wrt. MTU locking in ipv4, to
Hangbin Liu we give thanks for this.
10) Fix regression in SO_BINDTODEVIC handling wrt. UDP socket demux.
Paolo Abeni, he gave us this.
11) Range check coalescing parameters in mlx4 driver, thank you Moshe
Shemesh.
12) Some ipv6 ICMP error handling fixes in rxrpc, from our good brother
David Howells.
13) Fix kexec on mlx5 by freeing IRQs in shutdown path. Daniel Juergens,
you're the best!
14) Don't send bonding RLB updates to invalid MAC addresses. Debabrata
Benerjee saved us!
15) Uh oh, we were leaking in udp_sendmsg and ping_v4_sendmsg. The ship
is now water tight, thanks to Andrey Ignatov.
16) IPSEC memory leak in ixgbe from Colin Ian King, man we've got holes
everywhere!
17) Fix error path in tcf_proto_create, Jiri Pirko what would we do
without you!
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (92 commits)
net sched actions: fix refcnt leak in skbmod
net: sched: fix error path in tcf_proto_create() when modules are not configured
net sched actions: fix invalid pointer dereferencing if skbedit flags missing
ixgbe: fix memory leak on ipsec allocation
ixgbevf: fix ixgbevf_xmit_frame()'s return type
ixgbe: return error on unsupported SFP module when resetting
ice: Set rq_last_status when cleaning rq
ipv4: fix memory leaks in udp_sendmsg, ping_v4_sendmsg
mlxsw: core: Fix an error handling path in 'mlxsw_core_bus_device_register()'
bonding: send learning packets for vlans on slave
bonding: do not allow rlb updates to invalid mac
net/mlx5e: Err if asked to offload TC match on frag being first
net/mlx5: E-Switch, Include VF RDMA stats in vport statistics
net/mlx5: Free IRQs in shutdown path
rxrpc: Trace UDP transmission failure
rxrpc: Add a tracepoint to log ICMP/ICMP6 and error messages
rxrpc: Fix the min security level for kernel calls
rxrpc: Fix error reception on AF_INET6 sockets
rxrpc: Fix missing start of call timeout
qed: fix spelling mistake: "taskelt" -> "tasklet"
...
- Restore device_may_wakeup() check in pci_enable_wake() removed
inadvertently during the 4.13 cycle to prevent systems from
drawing excessive power when suspended or off, among other
things (Rafael Wysocki).
- Fix pci_dev_run_wake() to properly handle devices that only can
signal PME# when in the D3cold power state (Kai Heng Feng).
- Fix the schedutil cpufreq governor to avoid using UINT_MAX
as the new CPU frequency in some cases due to a missing check
(Rafael Wysocki).
- Remove a stale comment regarding worker kthreads from the
schedutil cpufreq governor (Juri Lelli).
- Fix a copy-paste mistake in the intel_pstate driver documentation
(Juri Lelli).
- Fix a typo in the system sleep states documentation (Jonathan
Neuschäfer).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=bCt1
-----END PGP SIGNATURE-----
Merge tag 'pm-4.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two PCI power management regressions from the 4.13 cycle and
one cpufreq schedutil governor bug introduced during the 4.12 cycle,
drop a stale comment from the schedutil code and fix two mistakes in
docs.
Specifics:
- Restore device_may_wakeup() check in pci_enable_wake() removed
inadvertently during the 4.13 cycle to prevent systems from drawing
excessive power when suspended or off, among other things (Rafael
Wysocki).
- Fix pci_dev_run_wake() to properly handle devices that only can
signal PME# when in the D3cold power state (Kai Heng Feng).
- Fix the schedutil cpufreq governor to avoid using UINT_MAX as the
new CPU frequency in some cases due to a missing check (Rafael
Wysocki).
- Remove a stale comment regarding worker kthreads from the schedutil
cpufreq governor (Juri Lelli).
- Fix a copy-paste mistake in the intel_pstate driver documentation
(Juri Lelli).
- Fix a typo in the system sleep states documentation (Jonathan
Neuschäfer)"
* tag 'pm-4.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PCI / PM: Check device_may_wakeup() in pci_enable_wake()
PCI / PM: Always check PME wakeup capability for runtime wakeup support
cpufreq: schedutil: Avoid using invalid next_freq
cpufreq: schedutil: remove stale comment
PM: docs: intel_pstate: fix Active Mode w/o HWP paragraph
PM: docs: sleep-states: Fix a typo ("includig")
- Fix for a 4.17-rc1 change to dm-bufio's buffer alignment.
- Fixes for a few sparse warnings.
- Remove VLA usage in DM mirror target.
- Improve DM thinp Documentation for the "read_only" feature.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJa9Gn4AAoJEMUj8QotnQNa+6sH/0lu9XA7fpaopD29wPkjtFLg
nDY8yCBrBvo1GRQBCAM3TWYDdTYLgO0srn24y9AM0AnhuiR+YFeDuoMyhzIQjWay
X+RGgiMtLwroLWO9t7hhP1eK3u3SX+40bhvle6vNOn/KGb7XOuFnEksUJ85B9pJZ
xF1aGos8+YIXTqBRP4RLJPWKPme1HIpdVGUcwnt9fW3J9PYzkN9xIry/cow0JWEl
xmr69l2KpOQ7jVpcBhA52NDosW/LCOipyr9mhe0+lq60BDcsCbjCkK5p6F38Ufa8
+24cqgdT2fdbogL3JTfs0lIgrOaLOhYmL5qJemopcxE6TKXvP6AzHhihlT48fNA=
=w2u8
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable fix for DM integrity to use kvfree
- fix for a 4.17-rc1 change to dm-bufio's buffer alignment
- fixes for a few sparse warnings
- remove VLA usage in DM mirror target
- improve DM thinp Documentation for the "read_only" feature
* tag 'for-4.17/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: update Documentation to clarify when "read_only" is valid
dm mirror: remove VLA usage
dm: fix some sparse warnings and whitespace in dax methods
dm cache background tracker: fix sparse warning
dm bufio: fix buffer alignment
dm integrity: use kvfree for kvmalloc'd memory
Due to user confusion, clarify that it doesn't make sense to try to
create a thin-pool with "read_only" mode enabled.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
P-state selection algorithm (powersave or performance) is selected by
echoing the desired choice to scaling_governor sysfs attribute and not
to scaling_cur_freq (as currently stated).
Fix it.
Signed-off-by: Juri Lelli <juri.lelli@redhat.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix a typo in admin-guide/pm/sleep-states.rst.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the example binding is used on a real dts file, the following DTC
warning is seen with W=1:
arch/arm/boot/dts/imx6q-b450v3.dtb: Warning (avoid_unnecessary_addr_size): /mdio-gpio/switch@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Remove unnecessary #address-cells/#size-cells to improve the binding
document examples.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull libata fixes from Tejun Heo:
"An earlier commit to add reset control for embedded ahci controllers
affected some of the hardware specific drivers and got reverted for
now.
Other than that, just per-device workarounds and trivial changes"
* 'for-4.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
driver core: add __printf verification to __ata_ehi_pushv_desc
ata: fix spelling mistake: "directon" -> "direction"
libata: Apply NOLPM quirk for SanDisk SD7UB3Q*G1001 SSDs
libata: Apply NOLPM quirk for SAMSUNG MZMPC128HBFU-000MV SSD
ata: ahci: mvebu: override ahci_stop_engine for mvebu AHCI
libahci: Allow drivers to override stop_engine
Revert "ata: ahci-platform: add reset control support"
Document the R-Car V3H (R8A77980) SoC support in the R-Car CAN-FD bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Document the R-Car V3M (R8A77970) SoC support in the R-Car CAN-FD bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Minor conflict, a CHECK was placed into an if() statement
in net-next, whilst a newline was added to that CHECK
call in 'net'. Thanks to Daniel for the merge resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=6jfk
-----END PGP SIGNATURE-----
Merge tag 'media/v4.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a trivial one-line fix addressing a PTR_ERR() getting value from a
wrong var at imx driver
- a patch changing my e-mail at the Kernel tree to mchehab@kernel.org.
no code changes
* tag 'media/v4.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
MAINTAINERS & files: Canonize the e-mails I use at files
media: imx-media-csi: Fix inconsistent IS_ERR and PTR_ERR
From now on, I'll start using my @kernel.org as my development e-mail.
As such, let's remove the entries that point to the old
mchehab@s-opensource.com at MAINTAINERS file.
For the files written with a copyright with mchehab@s-opensource,
let's keep Samsung on their names, using mchehab+samsung@kernel.org,
in order to keep pointing to my employer, with sponsors the work.
For the files written before I join Samsung (on July, 4 2013),
let's just use mchehab@kernel.org.
For bug reports, we can simply point to just kernel.org, as
this will reach my mchehab+samsung inbox anyway.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Brian Warner <brian.warner@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Pull networking fixes from David Miller:
1) Various sockmap fixes from John Fastabend (pinned map handling,
blocking in recvmsg, double page put, error handling during redirect
failures, etc.)
2) Fix dead code handling in x86-64 JIT, from Gianluca Borello.
3) Missing device put in RDS IB code, from Dag Moxnes.
4) Don't process fast open during repair mode in TCP< from Yuchung
Cheng.
5) Move address/port comparison fixes in SCTP, from Xin Long.
6) Handle add a bond slave's master into a bridge properly, from
Hangbin Liu.
7) IPv6 multipath code can operate on unitialized memory due to an
assumption that the icmp header is in the linear SKB area. Fix from
Eric Dumazet.
8) Don't invoke do_tcp_sendpages() recursively via TLS, from Dave
Watson.
9) Fix memory leaks in x86-64 JIT, from Daniel Borkmann.
10) RDS leaks kernel memory to userspace, from Eric Dumazet.
11) DCCP can invoke a tasklet on a freed socket, take a refcount. Also
from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (78 commits)
dccp: fix tasklet usage
smc: fix sendpage() call
net/smc: handle unregistered buffers
net/smc: call consolidation
qed: fix spelling mistake: "offloded" -> "offloaded"
net/mlx5e: fix spelling mistake: "loobpack" -> "loopback"
tcp: restore autocorking
rds: do not leak kernel memory to user land
qmi_wwan: do not steal interfaces from class drivers
ipv4: fix fnhe usage by non-cached routes
bpf: sockmap, fix error handling in redirect failures
bpf: sockmap, zero sg_size on error when buffer is released
bpf: sockmap, fix scatterlist update on error path in send with apply
net_sched: fq: take care of throttled flows before reuse
ipv6: Revert "ipv6: Allow non-gateway ECMP for IPv6"
bpf, x64: fix memleak when not converging on calls
bpf, x64: fix memleak when not converging after image
net/smc: restrict non-blocking connect finish
8139too: Use disable_irq_nosync() in rtl8139_poll_controller()
sctp: fix the issue that the cookie-ack with auth can't get processed
...
This is a sample application for AF_XDP sockets. The application
supports three different modes of operation: rxdrop, txonly and l2fwd.
To show-case a simple round-robin load-balancing between a set of
sockets in an xskmap, set the RR_LB compile time define option to 1 in
"xdpsock.h".
v2: The entries variable was calculated twice in {umem,xq}_nb_avail.
Co-authored-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The JIT compiler emits ia32 bit instructions. Currently, It supports eBPF
only. Classic BPF is supported because of the conversion by BPF core.
Almost all instructions from eBPF ISA supported except the following:
BPF_ALU64 | BPF_DIV | BPF_K
BPF_ALU64 | BPF_DIV | BPF_X
BPF_ALU64 | BPF_MOD | BPF_K
BPF_ALU64 | BPF_MOD | BPF_X
BPF_STX | BPF_XADD | BPF_W
BPF_STX | BPF_XADD | BPF_DW
It doesn't support BPF_JMP|BPF_CALL with BPF_PSEUDO_CALL at the moment.
IA32 has few general purpose registers, EAX|EDX|ECX|EBX|ESI|EDI. I use
EAX|EDX|ECX|EBX as temporary registers to simulate instructions in eBPF
ISA, and allocate ESI|EDI to BPF_REG_AX for constant blinding, all others
eBPF registers, R0-R10, are simulated through scratch space on stack.
The reasons behind the hardware registers allocation policy are:
1:MUL need EAX:EDX, shift operation need ECX, so they aren't fit
for general eBPF 64bit register simulation.
2:We need at least 4 registers to simulate most eBPF ISA operations
on registers operands instead of on register&memory operands.
3:We need to put BPF_REG_AX on hardware registers, or constant blinding
will degrade jit performance heavily.
Tested on PC (Intel(R) Core(TM) i5-5200U CPU).
Testing results on i5-5200U:
1) test_bpf: Summary: 349 PASSED, 0 FAILED, [319/341 JIT'ed]
2) test_progs: Summary: 83 PASSED, 0 FAILED.
3) test_lpm: OK
4) test_lru_map: OK
5) test_verifier: Summary: 828 PASSED, 0 FAILED.
Above tests are all done in following two conditions separately:
1:bpf_jit_enable=1 and bpf_jit_harden=0
2:bpf_jit_enable=1 and bpf_jit_harden=2
Below are some numbers for this jit implementation:
Note:
I run test_progs in kselftest 100 times continuously for every condition,
the numbers are in format: total/times=avg.
The numbers that test_bpf reports show almost the same relation.
a:jit_enable=0 and jit_harden=0 b:jit_enable=1 and jit_harden=0
test_pkt_access:PASS:ipv4:15622/100=156 test_pkt_access:PASS:ipv4:10674/100=106
test_pkt_access:PASS:ipv6:9130/100=91 test_pkt_access:PASS:ipv6:4855/100=48
test_xdp:PASS:ipv4:240198/100=2401 test_xdp:PASS:ipv4:138912/100=1389
test_xdp:PASS:ipv6:137326/100=1373 test_xdp:PASS:ipv6:68542/100=685
test_l4lb:PASS:ipv4:61100/100=611 test_l4lb:PASS:ipv4:37302/100=373
test_l4lb:PASS:ipv6:101000/100=1010 test_l4lb:PASS:ipv6:55030/100=550
c:jit_enable=1 and jit_harden=2
test_pkt_access:PASS:ipv4:10558/100=105
test_pkt_access:PASS:ipv6:5092/100=50
test_xdp:PASS:ipv4:131902/100=1319
test_xdp:PASS:ipv6:77932/100=779
test_l4lb:PASS:ipv4:38924/100=389
test_l4lb:PASS:ipv6:57520/100=575
The numbers show we get 30%~50% improvement.
See Documentation/networking/filter.txt for more information.
Changelog:
Changes v5-v6:
1:Add do {} while (0) to RETPOLINE_RAX_BPF_JIT for
consistence reason.
2:Clean up non-standard comments, reported by Daniel Borkmann.
3:Fix a memory leak issue, repoted by Daniel Borkmann.
Changes v4-v5:
1:Delete is_on_stack, BPF_REG_AX is the only one
on real hardware registers, so just check with
it.
2:Apply commit 1612a981b7 ("bpf, x64: fix JIT emission
for dead code"), suggested by Daniel Borkmann.
Changes v3-v4:
1:Fix changelog in commit.
I install llvm-6.0, then test_progs willn't report errors.
I submit another patch:
"bpf: fix misaligned access for BPF_PROG_TYPE_PERF_EVENT program type on x86_32 platform"
to fix another problem, after that patch, test_verifier willn't report errors too.
2:Fix clear r0[1] twice unnecessarily in *BPF_IND|BPF_ABS* simulation.
Changes v2-v3:
1:Move BPF_REG_AX to real hardware registers for performance reason.
3:Using bpf_load_pointer instead of bpf_jit32.S, suggested by Daniel Borkmann.
4:Delete partial codes in 1c2a088a66, suggested by Daniel Borkmann.
5:Some bug fixes and comments improvement.
Changes v1-v2:
1:Fix bug in emit_ia32_neg64.
2:Fix bug in emit_ia32_arsh_r64.
3:Delete filename in top level comment, suggested by Thomas Gleixner.
4:Delete unnecessary boiler plate text, suggested by Thomas Gleixner.
5:Rewrite some words in changelog.
6:CodingSytle improvement and a little more comments.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull input updates from Dmitry Torokhov:
"Just a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: atmel_mxt_ts - add missing compatible strings to OF device table
Input: atmel_mxt_ts - fix the firmware update
Input: atmel_mxt_ts - add touchpad button mapping for Samsung Chromebook Pro
MAINTAINERS: Rakesh Iyer can't be reached anymore
Input: hideep_ts - fix a typo in Kconfig
Input: alps - fix reporting pressure of v3 trackstick
Input: leds - fix out of bound access
Input: synaptics-rmi4 - fix an unchecked out of memory error path
Commit af503716ac ("i2c: core: report OF style module alias for devices
registered via OF") fixed how the I2C core reports the module alias when
devices are registered via OF.
But the atmel_mxt_ts driver only has an "atmel,maxtouch" compatible in its
OF device ID table, so if a Device Tree is using a different one, autoload
won't be working for the module (the matching works because the I2C device
ID table is used as a fallback).
So add compatible strings for each of the entries in the I2C device table.
Fixes: af503716ac ("i2c: core: report OF style module alias for devices registered via OF")
Reported-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[dtor: document which compatibles are deprecated and should not be used]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to introduce a new compatible name for the Meson-AXG SoC
in order to support the RMII 100M ethernet PHY, since the PRG_ETH0
register of the dwmac glue layer is changed from previous old SoC.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer fixes from Thomas Gleixner:
"Two fixes from the timer departement:
- Fix a long standing issue in the NOHZ tick code which causes RB
tree corruption, delayed timers and other malfunctions. The cause
for this is code which modifies the expiry time of an enqueued
hrtimer.
- Revert the CLOCK_MONOTONIC/CLOCK_BOOTTIME unification due to
regression reports. Seems userspace _is_ relying on the documented
behaviour despite our hope that it wont"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert: Unify CLOCK_MONOTONIC and CLOCK_BOOTTIME
tick/sched: Do not mess with an enqueued hrtimer
Pull i2c fixes from Wolfram Sang:
- two driver fixes
- better parameter check for the core
- Documentation updates
- part of a tree-wide HAS_DMA cleanup
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sprd: Fix the i2c count issue
i2c: sprd: Prevent i2c accesses after suspend is called
i2c: dev: prevent ZERO_SIZE_PTR deref in i2cdev_ioctl_rdwr()
Documentation/i2c: adopt kernel commenting style in examples
Documentation/i2c: sync docs with current state of i2c-tools
Documentation/i2c: whitespace cleanup
i2c: Remove depends on HAS_DMA in case of platform dependency
This patch adds a documentation for seg_flowlabel sysctl into
Documentation/networking/ip-sysctl.txt
Signed-off-by: Ahmed Abdelsalam <amsalam20@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARM:
- PSCI selection API, a leftover from 4.16 (for stable)
- Kick vcpu on active interrupt affinity change
- Plug a VMID allocation race on oversubscribed systems
- Silence debug messages
- Update Christoffer's email address (linaro -> arm)
x86:
- Expose userspace-relevant bits of a newly added feature
- Fix TLB flushing on VMX with VPID, but without EPT
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJa44lQAAoJEED/6hsPKofo1dIH/3n9AZSWvavgL2V3j6agT8Yy
hxF4nHCFEJd5aqDNwbG9QEzivKw88r3o3mdB2XAQESB2MlCYR1jkTONm7yvVJTs/
/P9gj+DEQbCj2AgT//u3BGsAsZDKFhB9JwfmV2Mp4zDIqWFa6oCOGeq/iPVAGDcN
vUpuYeIicuH9SRoxH7de3z+BEXW0O+gCABXQtvA93FKTMz35yFTgmbDVCnvaV0zL
3B+3/4/jdbTRICW8EX6Li43+gEBUMtnVNkdqxLPTuCtDG8iuPUGfgF02gH99/9gj
hliV3Q4VUZKkSABW5AqKPe4+9rbsHCh9eL0LpHFGI9y+6LeUIOXAX4CtohR8gWE=
=W9Vz
-----END PGP SIGNATURE-----
rMerge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- PSCI selection API, a leftover from 4.16 (for stable)
- Kick vcpu on active interrupt affinity change
- Plug a VMID allocation race on oversubscribed systems
- Silence debug messages
- Update Christoffer's email address (linaro -> arm)
x86:
- Expose userspace-relevant bits of a newly added feature
- Fix TLB flushing on VMX with VPID, but without EPT"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86/headers/UAPI: Move DISABLE_EXITS KVM capability bits to the UAPI
kvm: apic: Flush TLB after APIC mode/address change if VPIDs are in use
arm/arm64: KVM: Add PSCI version selection API
KVM: arm/arm64: vgic: Kick new VCPU on interrupt migration
arm64: KVM: Demote SVE and LORegion warnings to debug only
MAINTAINERS: Update e-mail address for Christoffer Dall
KVM: arm/arm64: Close VMID generation race
Here are some small driver core and firmware fixes for 4.17-rc3
There's a kobject WARN() removal to make syzkaller a lot happier about
some "normal" error paths that it keeps hitting, which should reduce the
number of false-positives we have been getting recently.
There's also some fimware test and documentation fixes, and the
coredump() function signature change that needed to happen after -rc1
before drivers started to take advantage of it.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWuMxrw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymFpQCg1JM62/W8e6mQ4vdZNQmAzgMKMEMAniOMcVRX
/oDWXp64mYwJu+GTxnIJ
=+9Gk
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are some small driver core and firmware fixes for 4.17-rc3
There's a kobject WARN() removal to make syzkaller a lot happier about
some "normal" error paths that it keeps hitting, which should reduce
the number of false-positives we have been getting recently.
There's also some fimware test and documentation fixes, and the
coredump() function signature change that needed to happen after -rc1
before drivers started to take advantage of it.
All of these have been in linux-next with no reported issues"
* tag 'driver-core-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
firmware: some documentation fixes
selftests:firmware: fixes a call to a wrong function name
kobject: don't use WARN for registration failures
firmware: Fix firmware documentation for recent file renames
test_firmware: fix setting old custom fw path back on exit, second try
test_firmware: Install all scripts
drivers: change struct device_driver::coredump() return type to void
Here are some tty and serial driver fixes for reported issues for
4.17-rc3.
Nothing major, but a number of small things:
- device tree fixes/updates for serial ports
- earlycon fixes
- n_gsm fixes
- tty core change reverted to help resolve syszkaller reports
- other serial driver small fixes
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWuM0Vg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yksXgCgqT2E9Ah5O/uZp3yGAjRILKjX294AoI46+t3W
Xy8WA1Fw1NCMBvfvCVIv
=gBd0
-----END PGP SIGNATURE-----
Merge tag 'tty-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for reported issues for
4.17-rc3.
Nothing major, but a number of small things:
- device tree fixes/updates for serial ports
- earlycon fixes
- n_gsm fixes
- tty core change reverted to help resolve syszkaller reports
- other serial driver small fixes
All of these have been in linux-next with no reported issues"
* tag 'tty-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Use __GFP_NOFAIL for tty_ldisc_get()
tty: serial: xuartps: Setup early console when uartclk is also passed
tty: Don't call panic() at tty_ldisc_init()
tty: Avoid possible error pointer dereference at tty_ldisc_restore().
dt-bindings: mvebu-uart: DT fix s/interrupts-names/interrupt-names/
tty: serial: qcom_geni_serial: Use signed variable to get IRQ
earlycon: Use a pointer table to fix __earlycon_table stride
serial: sh-sci: Document r8a77470 bindings
dt-bindings: meson-uart: DT fix s/clocks-names/clock-names/
serial: imx: fix cached UCR2 read on software reset
serial: imx: warn user when using unsupported configuration
serial: mvebu-uart: Fix local flags handling on termios update
tty: n_gsm: Fix DLCI handling for ADM mode if debug & 2 is not set
tty: n_gsm: Fix long delays with control frame timeouts in ADM mode
Here are 2 staging driver fixups for 4.17-rc3.
The first is the remaining stragglers of the irda code removal that you
pointed out during the merge window. The second is a fix for the
wilc1000 driver due to a patch that got merged in 4.17-rc1.
Both of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWuMyew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymXxACffYtMbj0Vg5pD0yAPqRzJ2iVMVE0AnRkp4BYQ
kXgAjDeSyrdKPUwQ7Hl2
=UNuF
-----END PGP SIGNATURE-----
Merge tag 'staging-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are two staging driver fixups for 4.17-rc3.
The first is the remaining stragglers of the irda code removal that
you pointed out during the merge window. The second is a fix for the
wilc1000 driver due to a patch that got merged in 4.17-rc1.
Both of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: wilc1000: fix NULL pointer exception in host_int_parse_assoc_resp_info()
staging: irda: remove remaining remants of irda code removal
Here are a number of USB driver fixes for reported problems for
4.17-rc3.
The "largest" here is a number of phy core changes for reported problems
with the -rc1 release. There's also the usual musb and xhci fixes, as
well as new device id updates. There are also some usbip fixes for
reported problems as more people start to use that code with containers.
All of these have been in linux-next with no reported issues, except the
last few new device ids, which are "obviously correct" :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWuM0+g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynJ0QCfShhVDAuE1neAmu4vF9HFY8eoe3UAn1b71qRn
UJ5VIrtn1cS0bB3tPwmu
=sdc6
-----END PGP SIGNATURE-----
Merge tag 'usb-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB driver fixes for reported problems for
4.17-rc3.
The "largest" here is a number of phy core changes for reported
problems with the -rc1 release. There's also the usual musb and xhci
fixes, as well as new device id updates. There are also some usbip
fixes for reported problems as more people start to use that code with
containers.
All of these have been in linux-next with no reported issues, except
the last few new device ids, which are "obviously correct" :)"
* tag 'usb-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: musb: dsps: drop duplicate phy initialisation
USB: musb: host: prevent core phy initialisation
usb: core: phy: add the SPDX-License-Identifier and include guard
xhci: Fix Kernel oops in xhci dbgtty
usb: select USB_COMMON for usb role switch config
usb: core: phy: add missing forward declaration for "struct device"
usb: core: phy: make it a no-op if CONFIG_GENERIC_PHY is disabled
usb: core: use phy_exit during suspend if wake up is not supported
usb: core: split usb_phy_roothub_{init,alloc}
usb: core: phy: fix return value of usb_phy_roothub_exit()
usb: typec: ucsi: Increase command completion timeout value
Revert "xhci: plat: Register shutdown for xhci_plat"
usb: core: Add quirk for HP v222w 16GB Mini
Documentation: typec.rst: Use literal-block element with ascii art
usb: typec: ucsi: fix tracepoint related build error
usbip: usbip_event: fix to not print kernel pointer address
usbip: usbip_host: fix to hold parent lock for device_attach() calls
usbip: vhci_hcd: Fix usb device and sockfd leaks
usbip: vhci_hcd: check rhport before using in vhci_hub_control()
USB: Increment wakeup count on remote wakeup.
...
When CONFIG_BPF_JIT_ALWAYS_ON is enabled, kernel has limitation for
bpf_jit_enable, so it has fixed value 1 and we cannot set it to 2
for JIT opcode dumping; this patch is to update the doc for it.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Only the overlay notifier callbacks have a chance to potentially get
hold of references to those two resources, but they are not supposed to
store them beyond OF_OVERLAY_POST_REMOVE.
Document the overlay notifier API, its constraint regarding pointer
lifetime, and then remove intentional leaks of ovcs->overlay_tree and
ovcs->fdt from free_overlay_changeset.
See also https://lkml.org/lkml/2018/4/23/1063 and following.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Virtual devices such as tunnels and bonding can handle large packets.
Only segment packets when reaching a physical or loopback device.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert commits
92af4dcb4e ("tracing: Unify the "boot" and "mono" tracing clocks")
127bfa5f43 ("hrtimer: Unify MONOTONIC and BOOTTIME clock behavior")
7250a4047a ("posix-timers: Unify MONOTONIC and BOOTTIME clock behavior")
d6c7270e91 ("timekeeping: Remove boot time specific code")
f2d6fdbfd2 ("Input: Evdev - unify MONOTONIC and BOOTTIME clock behavior")
d6ed449afd ("timekeeping: Make the MONOTONIC clock behave like the BOOTTIME clock")
72199320d4 ("timekeeping: Add the new CLOCK_MONOTONIC_ACTIVE clock")
As stated in the pull request for the unification of CLOCK_MONOTONIC and
CLOCK_BOOTTIME, it was clear that we might have to revert the change.
As reported by several folks systemd and other applications rely on the
documented behaviour of CLOCK_MONOTONIC on Linux and break with the above
changes. After resume daemons time out and other timeout related issues are
observed. Rafael compiled this list:
* systemd kills daemons on resume, after >WatchdogSec seconds
of suspending (Genki Sky). [Verified that that's because systemd uses
CLOCK_MONOTONIC and expects it to not include the suspend time.]
* systemd-journald misbehaves after resume:
systemd-journald[7266]: File /var/log/journal/016627c3c4784cd4812d4b7e96a34226/system.journal
corrupted or uncleanly shut down, renaming and replacing.
(Mike Galbraith).
* NetworkManager reports "networking disabled" and networking is broken
after resume 50% of the time (Pavel). [May be because of systemd.]
* MATE desktop dims the display and starts the screensaver right after
system resume (Pavel).
* Full system hang during resume (me). [May be due to systemd or NM or both.]
That happens on debian and open suse systems.
It's sad, that these problems were neither catched in -next nor by those
folks who expressed interest in this change.
Reported-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Reported-by: Genki Sky <sky@genki.is>,
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kevin Easton <kevin@guarana.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Salyzyn <salyzyn@android.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Including:
- Fixup outdated kernel-doc paths
- Slightly too short title underline
- Some typos
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Distributed filesystems are most effective when the server and client
clocks are synchronised. Embedded devices often use NFS for their
root filesystem but typically do not contain an RTC, so the clocks of
the NFS server and the embedded device will be out-of-sync when the root
filesystem is mounted (and may not be synchronised until late in the
boot process).
Extend ipconfig with the ability to export IP addresses of NTP servers
it discovers to /proc/net/ipconfig/ntp_servers. They can be supplied as
follows:
- If ipconfig is configured manually via the "ip=" or "nfsaddrs="
kernel command line parameters, one NTP server can be specified in
the new "<ntp0-ip>" parameter.
- If ipconfig is autoconfigured via DHCP, request DHCP option 42 in
the DHCPDISCOVER message, and record the IP addresses of up to three
NTP servers sent by the responding DHCP server in the subsequent
DHCPOFFER message.
ipconfig will only write the NTP server IP addresses it discovers to
/proc/net/ipconfig/ntp_servers, one per line (in the order received from
the DHCP server, if DHCP autoconfiguration is used); making use of these
NTP servers is the responsibility of a user space process (e.g. an
initrd/initram script that invokes an NTP client before mounting an NFS
root filesystem).
Signed-off-by: Chris Novakovic <chris@chrisn.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
