* 'for-usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
Intel xhci: Limit number of active endpoints to 64.
Intel xhci: Ignore spurious successful event.
Intel xhci: Support EHCI/xHCI port switching.
Intel xhci: Add PCI id for Panther Point xHCI host.
xhci: STFU: Be quieter during URB submission and completion.
xhci: STFU: Don't print event ring dequeue pointer.
xhci: STFU: Remove function tracing.
xhci: Don't submit commands when the host is dead.
xhci: Clear stopped_td when Stop Endpoint command completes.
The Panther Point chipset has an xHCI host controller that has a limit to
the number of active endpoints it can handle. Ideally, it would signal
that it can't handle anymore endpoints by returning a Resource Error for
the Configure Endpoint command, but they don't. Instead it needs software
to keep track of the number of active endpoints, across configure endpoint
commands, reset device commands, disable slot commands, and address device
commands.
Add a new endpoint context counter, xhci_hcd->num_active_eps, and use it
to track the number of endpoints the xHC has active. This gets a little
tricky, because commands to change the number of active endpoints can
fail. This patch adds a new xHCI quirk for these Intel hosts, and the new
code should not have any effect on other xHCI host controllers.
Fail a new device allocation if we don't have room for the new default
control endpoint. Use the endpoint ring pointers to determine what
endpoints were active before a Reset Device command or a Disable Slot
command, and drop those once the command completes.
Fail a configure endpoint command if it would add too many new endpoints.
We have to be a bit over zealous here, and only count the number of new
endpoints to be added, without subtracting the number of dropped
endpoints. That's because a second configure endpoint command for a
different device could sneak in before we know if the first command is
completed. If the first command dropped resources, the host controller
fails the command for some reason, and we're nearing the limit of
endpoints, we could end up oversubscribing the host.
To fix this race condition, when evaluating whether a configure endpoint
command will fix in our bandwidth budget, only add the new endpoints to
xhci->num_active_eps, and don't subtract the dropped endpoints. Ignore
changed endpoints (ones that are dropped and then re-added), as that
shouldn't effect the host's endpoint resources. When the configure
endpoint command completes, subtract off the dropped endpoints.
This may mean some configuration changes may temporarily fail, but it's
always better to under-subscribe than over-subscribe resources.
(Originally my plan had been to push the resource allocation down into the
ring allocation functions. However, that would cause us to allocate
unnecessary resources when endpoints were changed, because the xHCI driver
allocates a new ring for the changed endpoint, and only deletes the old
ring once the Configure Endpoint command succeeds. A further complication
would have been dealing with the per-device endpoint ring cache.)
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The xHCI host controller in the Panther Point chipset sometimes produces
spurious events on the event ring. If it receives a short packet, it
first puts a Transfer Event with a short transfer completion code on the
event ring. Then it puts a Transfer Event with a successful completion
code on the ring for the same TD. The xHCI driver correctly processes the
short transfer completion code, gives the URB back to the driver, and then
prints a warning in dmesg about the spurious event. These warning
messages really fill up dmesg when an HD webcam is plugged into xHCI.
This spurious successful event behavior isn't technically disallowed by
the xHCI specification, so make the xHCI driver just ignore the spurious
completion event.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The Intel Panther Point chipsets contain an EHCI and xHCI host controller
that shares some number of skew-dependent ports. These ports can be
switched from the EHCI to the xHCI host (and vice versa) by a hardware MUX
that is controlled by registers in the xHCI PCI configuration space. The
USB 3.0 SuperSpeed terminations on the xHCI ports can be controlled
separately from the USB 2.0 data wires.
This switchover mechanism is there to support users who do a custom
install of certain non-Linux operating systems that don't have official
USB 3.0 support. By default, the ports are under EHCI, SuperSpeed
terminations are off, and USB 3.0 devices will show up under the EHCI
controller at reduced speeds. (This was more palatable for the marketing
folks than having completely dead USB 3.0 ports if no xHCI drivers are
available.) Users should be able to turn on xHCI by default through a
BIOS option, but users are happiest when they don't have to change random
BIOS settings.
This patch introduces a driver method to switchover the ports from EHCI to
xHCI before the EHCI driver finishes PCI enumeration. We want to switch
the ports over before the USB core has the chance to enumerate devices
under EHCI, or boot from USB mass storage will fail if the boot device
connects under EHCI first, and then gets disconnected when the port
switches over to xHCI.
Add code to the xHCI PCI quirk to switch the ports from EHCI to xHCI. The
PCI quirks code will run before any other PCI probe function is called, so
this avoids the issue with boot devices.
Another issue is with BIOS behavior during system resume from hibernate.
If the BIOS doesn't support xHCI, it may switch the devices under EHCI to
allow use of the USB keyboard, mice, and mass storage devices. It's
supposed to remember the value of the port routing registers and switch
them back when the OS attempts to take control of the xHCI host controller,
but we all know not to trust BIOS writers.
Make both the xHCI driver and the EHCI driver attempt to switchover the
ports in their PCI resume functions. We can't guarantee which PCI device
will be resumed first, so this avoids any race conditions. Writing a '1'
to an already set port switchover bit or a '0' to a cleared port switchover
bit should have no effect.
The xHCI PCI configuration registers will be documented in the EDS-level
chipset spec, which is not public yet. I have permission from legal and
the Intel chipset group to release this patch early to allow good Linux
support at product launch. I've tried to document the registers as much
as possible, so please let me know if anything is unclear.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The twl6025 uses a different regulator for USB than the 6030 so select
the correct regulator name depending on the subclass of device.
Since V1
Use features passed via platform data instead of global variable.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Unsurprisingly, URBs get submitted and completed a lot in the xHCI
driver. If we have to print 10 lines of debug for every URB submitted
or completed, then that can cause the whole system to stay in the
interrupt handler too long, and can cause Missed Service completion
codes for isochronous transfers.
Cut down the debugging in the URB submission and completion paths:
- Don't squawk about successful transfers, only unsuccessful ones.
- Only print the number of bytes transferred if this was a short
transfer.
- Don't print the endpoint index for successful transfers (will add
more debug to failed transfers to show endpoint index there later).
- Stop printing MMIO writes. This debugging shows up when the endpoint
doorbell is rung a to start a transfer (basically for every URB).
- Don't print out the ring enqueue and dequeue pointers
- Stop printing when we're pointing to a link TRB.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Stop printing out the event ring dequeue pointer and status register in
the operational register set. The host will report an OK status 99% of
the time the interrupt handler is called, and usually when it's really
hosed, a host controller won't even call the interrupt handler. So the
line is really useless.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Remove unnecessary debugging from the xHCI driver. We don't need to
know what function we're calling or returning from. Now I know how to
use markup-oops.pl to de-mystify stack dumps of crashes.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When the xHCI host controller dies, the USB core may attempt to reset the
devices to their default configuration before disconnecting them. This
causes calls into the xHCI bandwidth allocation functions. Don't allow
those functions to submit commands or work on xHCI structures if the host
controller is marked as dying.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When an URB is cancelled, the xHCI driver issues a Stop Endpoint command
so that it can manipulate the ring and remove the transfer. The xHC
hardware then places a transfer event with the completion code "Stopped"
or "Stopped Invalid" to let the driver know what TD it was in the middle
of processing. This TD and TRB is stored in ep->stopped_td and
ep->stopped_trb. These pointers are also used in handling stalled
endpoints.
By design, the Stop Endpoint command can race with URB completion. By
the time the Stop Endpoint command is handled, the URBs to be cancelled
may have been given back to the driver. Unfortunately, the stopped_td
and stopped_trb pointers were not getting cleared in this case.
The USB core unconditionally tries to reset the toggle bits on any
endpoints when a new alternate interface setting is installed. When the
xHCI driver saw that ep->stopped_td was still set from the Stop Endpoint
command, xhci_reset_endpoint assumed the endpoint was actually stalled,
and attempted to clean up the endpoint rings. This would manifest
itself in a failed Reset Endpoint command and failed Set TR dequeue
Pointer command after a successful Configure Endpoint command. It may
have also been causing driver oops when the stopped_td was accessed.
This patch should be backported to stable kernels since 2.6.31. Before
2.6.33, stopped_td was found in the xhci_endpoint_ring, not the
xhci_virt_ep.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: Make struct pcmcia_device_id const, sound drivers edition
staging: pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Make declaration and uses of struct pcmcia_device_id const
pcmcia/sa1100: put sa11x0_pcmcia_hw_init[] to .devinit.data
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
USB: UHCI: Support big endian GRUSBHC HC
sparc: add {read,write}*_be routines
USB: UHCI: Add support for big endian descriptors
USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
USB: UHCI: Add support for big endian mmio
usb-storage: Correct adjust_quirks to include latest flags
usb/isp1760: Fix possible unlink problems
usb/isp1760: Move function isp1760_endpoint_disable() within file.
USB: remove remaining usages of hcd->state from usbcore and fix regression
usb: musb: ux500: add configuration and build options for ux500 dma
usb: musb: ux500: add dma glue layer for ux500
usb: musb: ux500: add dma name for ux500
usb: musb: ux500: add ux500 specific code for gadget side
usb: musb: fix compile error
usb-storage: fix up the unusual_realtek device list
USB: gadget: f_audio: Fix invalid dereference of initdata
EHCI: don't rescan interrupt QHs needlessly
OHCI: fix regression caused by nVidia shutdown workaround
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (110 commits)
[SCSI] qla2xxx: Refactor call to qla2xxx_read_sfp for thermal temperature.
[SCSI] qla2xxx: Unify the read/write sfp mailbox command routines.
[SCSI] qla2xxx: Clear complete initialization control block.
[SCSI] qla2xxx: Allow an override of the registered maximum LUN.
[SCSI] qla2xxx: Add host number in reset and quiescent message logs.
[SCSI] qla2xxx: Correctly read sfp single byte mailbox register.
[SCSI] qla2xxx: Add qla82xx_rom_unlock() function.
[SCSI] qla2xxx: Log if qla82xx firmware fails to load from flash.
[SCSI] qla2xxx: Use passed in host to initialize local scsi_qla_host in queuecommand function
[SCSI] qla2xxx: Correct buffer start in edc sysfs debug print.
[SCSI] qla2xxx: Update firmware version after flash update for ISP82xx.
[SCSI] qla2xxx: Fix hang during driver unload when vport is active.
[SCSI] qla2xxx: Properly set the dsd_list_len for dsd_chaining in cmd type 6.
[SCSI] qla2xxx: Fix virtual port failing to login after chip reset.
[SCSI] qla2xxx: Fix vport delete hang when logins are outstanding.
[SCSI] hpsa: Change memset using sizeof(ptr) to sizeof(*ptr)
[SCSI] ipr: Rate limit DMA mapping errors
[SCSI] hpsa: add P2000 to list of shared SAS devices
[SCSI] hpsa: do not attempt PCI power management reset method if we know it won't work.
[SCSI] hpsa: remove superfluous sleeps around reset code
...
Commit e66eed651f ("list: remove prefetching from regular list
iterators") removed the include of prefetch.h from list.h, which
uncovered several cases that had apparently relied on that rather
obscure header file dependency.
So this fixes things up a bit, using
grep -L linux/prefetch.h $(git grep -l '[^a-z_]prefetchw*(' -- '*.[ch]')
grep -L 'prefetchw*(' $(git grep -l 'linux/prefetch.h' -- '*.[ch]')
to guide us in finding files that either need <linux/prefetch.h>
inclusion, or have it despite not needing it.
There are more of them around (mostly network drivers), but this gets
many core ones.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
{read,write}l_be are now defined for SPARC and do not need to be
defined for SPARC_LEON in ehci.h. This patch fixes the following
warnings:
CC drivers/usb/host/ehci-hcd.o
In file included from drivers/usb/host/ehci-hcd.c:119:
drivers/usb/host/ehci.h:631:1: warning: "readl_be" redefined
...
drivers/usb/host/ehci-hcd.c:119:
drivers/usb/host/ehci.h:632:1: warning: "writel_be" redefined
...
Signed-off-by: Jan Andersson <jan@gaisler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for big endian GRUSBHC UHCI controllers.
The HCD bus glue will probe the register interface to determine
the endianness of the controller.
Tested on GR-LEON4-ITX board which has a controller with little endian
interface and on custom LEON3 board with a BE controller.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for universal host controllers that use
big endian descriptors. Support for BE descriptors requires a non-PCI
host controller. For kernels with PCI-only UHCI there should be no
change in behaviour.
This patch tries to replicate the technique used to support BE descriptors
in the EHCI HCD. Parts added to uhci-hcd.h are basically copy'n'paste from
ehci.h.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1462) updates the special accessor functions defined in
uhci-hcd.h. Rather than using a full compiler barrier, all we really
need is the ACCESS_ONCE() mechanism, because the idea is to force the
compiler to store a fixed copy of a possibly changing value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for big endian mmio to the UHCI HCD. Big endian
mmio is supported by adding a flag bit to the UHCI HCD replicating the
solution used in the EHCI HCD.
When adding big endian support this patch also adds a check to see if we
need to support HCs with PCI I/O registers when we support HCs with MMIO.
This patch also adds 'const' to the register access functions' uhci_hcd
argument.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commits ae38c78a03
and 00914025cc added quirk flags
US_FL_NO_READ_DISC_INFO and US_FL_NO_READ_CAPACITY_16 to
the usb-storage driver. However they did not add the corresponding flags
to adjust_quirks() in usb.c, so there was no facility for a user
to over-ride/add them via the quirks module parameter.
Signed-off-by: Karl Relton <karllinuxtest.relton@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use skip map to avoid spurious interrupts from unlinked transfers.
Also changes to urb_dequeue() and endpoint_disable() to avoid
release of spinlock in uncertain state.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Preparation for patch #2. The function isp1760_endpoint_disable() does almost
the same thing as urb_dequeue(). In patch #2 I change these to use a common
helper function instead of calling each other - for clarity but also to
avoid releasing the spinlock while in a "questionable" state. It seemed
proper to have these functions close to each other in the code.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1467) removes the last usages of hcd->state from
usbcore. We no longer check to see if an interrupt handler finds that
a controller has died; instead we rely on host controller drivers to
make an explicit call to usb_hc_died().
This fixes a regression introduced by commit
9b37596a2e (USB: move usbcore away from
hcd->state). It used to be that when a controller shared an IRQ with
another device and an interrupt arrived while hcd->state was set to
HC_STATE_HALT, the interrupt handler would be skipped. The commit
removed that test; as a result the current code doesn't skip calling
the handler and ends up believing the controller has died, even though
it's only temporarily stopped. The solution is to ignore HC_STATE_HALT
following the handler's return.
As a consequence of this change, several of the host controller
drivers need to be modified. They can no longer implicitly rely on
usbcore realizing that a controller has died because of hcd->state.
The patch adds calls to usb_hc_died() in the appropriate places.
The patch also changes a few of the interrupt handlers. They don't
expect to be called when hcd->state is equal to HC_STATE_HALT, even if
the controller is still alive. Early returns were added to avoid any
confusion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Manuel Lauss <manuel.lauss@googlemail.com>
CC: Rodolfo Giometti <giometti@linux.it>
CC: Olav Kongas <ok@artecdesign.ee>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Unaligned sizes and buffers are not supported and they will be filtered
out by is_compatible().
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Although U8500 and U5500 platforms use paltform dma, Inventra dma specific code
can work for them for the most part. Only difference is for the Rx path where
this patch is making use of request->short_not_ok to select dma mode.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 35a83365da6aa10095c6138cc428c15853409c32
(usb: musb: drop unneeded musb_debug trickery)
introduced a compile error for blackfin and
tusb6010 glue layers. Fix it.
Reported-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch (as1461) fixes the unusual_devs entries for the Realtek USB
card reader. They should be ordered by PID, and they should not
override the Subclass and Protocol values provided by the device.
Otherwise a notification about unnecessary entries gets printed in the
kernel log during probing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-By: Tony Vroon <tony@linx.net>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
as_out_ep_desc contines to be used during gadget enumeration and thus
should not be marked as __initdata
Signed-off-by: Martin Jackson <mjackson220.list@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1466) speeds up processing of ehci-hcd's periodic list.
The existing code will pointlessly rescan an interrupt endpoint queue
each time it encounters the queue's QH in the periodic list, which can
happen quite a few times if the endpoint's period is low. On some
embedded systems, this useless overhead can waste so much time that
the driver falls hopelessly behind and loses events.
The patch introduces a "periodic_stamp" variable, which gets
incremented each time scan_periodic() runs and each time the scan
advances to a new frame. If the corresponding stamp in an interrupt
QH is equal to the current periodic_stamp, we assume the QH has
already been scanned and skip over it. Otherwise we scan the QH as
usual, and if none of its URBs have completed then we store the
current periodic_stamp in the QH's stamp, preventing it from being
scanned again.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1463) fixes a regression caused by commit
3df7169e73 (OHCI: work around for nVidia
shutdown problem).
The original problem encountered by people using NVIDIA chipsets was
that USB devices were not turning off when the system shut down. For
example, the LED on an optical mouse would remain on, draining a
laptop's battery. The problem was caused by a bug in the chipset; an
OHCI controller in the Reset state would continue to drive a bus reset
signal even after system shutdown. The workaround was to put the
controllers into the Suspend state instead.
It turns out that later NVIDIA chipsets do not suffer from this bug.
Instead some have the opposite bug: If a system is shut down while an
OHCI controller is in the Suspend state, USB devices remain powered!
On other systems, shutting down with a Suspended controller causes the
system to reboot immediately. Thus, working around the original bug
on some machines exposes other bugs on other machines.
The best solution seems to be to limit the workaround to OHCI
controllers with a low-numbered PCI product ID. I don't know exactly
at what point NVIDIA changed their chipsets; the value used here is a
guess. So far it was worked out okay for all the people who have
tested it.
This fixes Bugzilla #35032.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andre "Osku" Schmidt <andre.osku.schmidt@googlemail.com>
Tested-by: Yury Siamashka <yurand2@gmail.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If for some reason we fail to set the voltage range for the VDDCX regulator
when removing it's better to still disable and free the regulator as that
avoids leaking a reference to it and is likely to ensure that it's turned
off completely.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When not active the hardware should be able to tolerate voltages within
the normal operating range so when removing set the maximum voltage we
can use to the maximum rather than minimum of the operating range. This
will improve interoperability in case we end up sharing the supply in
some design.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I am sharing patch to the devices/usb/serial/option.c. This allows
operation of Huawei E353 broadband modem using the “option” driver. The
patch simply adds new constant with proper product ID and an entry to
usb_device_id. I worked on the 2.6.38.6 sources. Tested on Dell inspiron
1764 (i3 core cpu) and brand new Huawei E353 modem, Fedora 15 beta.
Looking at the type of change, i doubt it has potential to introduce
problems in other parts of kernel or the driver itself.
Signed-off-by: Marcin Galczynski <marcin@galczynski.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the USB core wants to change to an alternate interface setting that
doesn't include an active endpoint, or de-configuring the device, the xHCI
driver needs to issue a Configure Endpoint command to tell the host to
drop some endpoints from the schedule. After the command completes, the
xHCI driver needs to free rings for any endpoints that were dropped.
Unfortunately, the xHCI driver wasn't actually freeing the endpoint rings
for dropped endpoints. The rings would be freed if the endpoint's
information was simply changed (and a new ring was installed), but dropped
endpoints never had their rings freed. This caused errors when the ring
segment DMA pool was freed when the xHCI driver was unloaded:
[ 5582.883995] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff88003371d000 busy
[ 5582.884002] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880033716000 busy
[ 5582.884011] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880033455000 busy
[ 5582.884018] xhci_hcd 0000:06:00.0: Freed segment pool
[ 5582.884026] xhci_hcd 0000:06:00.0: Freed device context pool
[ 5582.884033] xhci_hcd 0000:06:00.0: Freed small stream array pool
[ 5582.884038] xhci_hcd 0000:06:00.0: Freed medium stream array pool
[ 5582.884048] xhci_hcd 0000:06:00.0: xhci_stop completed - status = 1
[ 5582.884061] xhci_hcd 0000:06:00.0: USB bus 3 deregistered
[ 5582.884193] xhci_hcd 0000:06:00.0: PCI INT A disabled
Fix this issue and free endpoint rings when their endpoints are
successfully dropped.
This patch should be backported to kernels as old as 2.6.31.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
When an endpoint ring is freed, it is either cached in a per-device ring
cache, or simply freed if the ring cache is full. If the ring was added
to the cache, then virt_dev->num_rings_cached is incremented. The cache
is designed to hold up to 31 endpoint rings, in array indexes 0 to 30.
When the device is freed (when the slot was disabled),
xhci_free_virt_device() is called, it would free the cached rings in
array indexes 0 to virt_dev->num_rings_cached.
Unfortunately, the original code in xhci_free_or_cache_endpoint_ring()
would put the first entry into the ring cache in array index 1, instead of
array index 0. This was caused by the second assignment to rings_cached:
rings_cached = virt_dev->num_rings_cached;
if (rings_cached < XHCI_MAX_RINGS_CACHED) {
virt_dev->num_rings_cached++;
rings_cached = virt_dev->num_rings_cached;
virt_dev->ring_cache[rings_cached] =
virt_dev->eps[ep_index].ring;
This meant that when the device was freed, cached rings with indexes 0 to
N would be freed, and the last cached ring in index N+1 would not be
freed. When the driver was unloaded, this caused interesting messages
like:
xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880063040000 busy
This should be queued to stable kernels back to 2.6.33.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Dmitry's patch
dfa49c4ad1 USB: xhci - fix math in xhci_get_endpoint_interval()
introduced a bug. The USB 2.0 spec says that full speed isochronous endpoints'
bInterval must be decoded as an exponent to a power of two (e.g. interval =
2^(bInterval - 1)). Full speed interrupt endpoints, on the other hand, don't
use exponents, and the interval in frames is encoded straight into bInterval.
Dmitry's patch was supposed to fix up the full speed isochronous to parse
bInterval as an exponent, but instead it changed the *interrupt* endpoint
bInterval decoding. The isochronous endpoint encoding was the same.
This caused full speed devices with interrupt endpoints (including mice, hubs,
and USB to ethernet devices) to fail under NEC 0.96 xHCI host controllers:
[ 100.909818] xhci_hcd 0000:06:00.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x99, new slot info = 0x38100000
[ 100.909821] xhci_hcd 0000:06:00.0: xhci_check_bandwidth called for udev ffff88011f0ea000
...
[ 100.910187] xhci_hcd 0000:06:00.0: ERROR: unexpected command completion code 0x11.
[ 100.910190] xhci_hcd 0000:06:00.0: xhci_reset_bandwidth called for udev ffff88011f0ea000
When the interrupt endpoint was added and a Configure Endpoint command was
issued to the host, the host controller would return a very odd error message
(0x11 means "Slot Not Enabled", which isn't true because the slot was enabled).
Probably the host controller was getting very confused with the bad encoding.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Dmitry Torokhov <dtor@vmware.com>
Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Tested-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-next' of master.kernel.org:/pub/scm/linux/kernel/git/balbi/usb:
MAINTAINERS: tree moved to kernel.org
usb: musb: Calling VBUS pulsing API when SRP is initiated.
usb: otg: TWL6030: OMAP4430: Adding SRP VBUS pulsing API
usb: musb: host: remove duplicate check in musb_ep_program()
usb: musb: export musb_interrupt symbol
usb: musb: allow musb and glue layers to be modules
usb: musb: drop unneeded musb_debug trickery
composite.c always sets req->length to zero
and expects function driver's setup handlers
to return the amount of bytes to be used
on req->length. If we test against req->length
w_length will always be greater than req->length
thus making us always stall that particular
SEND_ENCAPSULATED_COMMAND request.
Tested against a Windows XP SP3.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
on 9g20 they are the same as the 9260
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Several resources have been allocated before this kmalloc failure, and thus
they should be released in this error handling code, as done in nearby
error handling code.
The semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression urb;
statement S;
position p1,p2;
@@
urb = usb_alloc_urb@p1(...);
... when != urb
if (urb == NULL) S
... when != urb
(
return <+...urb...+>;
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
cocci.print_main("",p1)
cocci.print_secs("",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the checkpatch warnings listed below:
WARNING: braces {} are not necessary for any arm of this statement
WARNING: please, no space before tabs
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the checkpatch error and warning listed below:
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement the start_srp API to generate the VBUS pulsing and assign it to
otg_transciever function pointer. This will be used by the link driver when
there is SRP initiation from user.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb_ep_program() contains obviously duplicate check for 'dma_channel' in its
IN/receive path -- removing it allows to save one level of indentation. While
at it, improve the comment style...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
currently that's used by another module
(am35x) which, granted, it shouldn't be
using that, but in order to avoid compile
errors, let's export that symbol temporarily
until re-factoring work is done on that
driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This in part reverts commit 7a180e70cf.
(usb: musb: temporarily make it bool) and while
at that we also allow glue layers to be compiled
as modules.
There are still some other changes needed
until we can have a fully functional build
with this setup, but we're getting there.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We have a generic way of enabling/disabling
different debug messages on a driver called
DYNAMIC_PRINTK. Anyone interested in enabling
just part of the debug messages, please read
the documentation under:
Documentation/dynamic-debug-howto.txt
for information on how to use that great
infrastructure.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are several functions using same code to get max ports and port array,
this patch moves the common code to a function in order to reuse them easily.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The BIOS handoff for the unused EHCI controller on the ExoPC tablet
hangs for 90 seconds on boot. Detect that device, skip negotiation
and force the handoff.
Signed-off-by: Andy Ross <andy.ross@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Factor the handoff code out from quirk_usb_disable_ehci
Signed-off-by: Andy Ross <andy.ross@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the xHCI driver attempts to cancel a transfer, it issues a Stop
Endpoint command and waits for the host controller to indicate which TRB
it was in the middle of processing. The host will put an event TRB with
completion code COMP_STOP on the event ring if it stops on a control
transfer TRB (or other types of transfer TRBs). The ring handling code
is supposed to set ep->stopped_trb to the TRB that the host stopped on
when this happens.
Unfortunately, there is a long-standing bug in the control transfer
completion code. It doesn't actually check to see if COMP_STOP is set
before attempting to process the transfer based on which part of the
control TD completed. So when we get an event on the data phase of the
control TRB with COMP_STOP set, it thinks it's a normal completion of
the transfer and doesn't set ep->stopped_td or ep->stopped_trb.
When the ring handling code goes on to process the completion of the Stop
Endpoint command, it sees that ep->stopped_trb is not a part of the TD
it's trying to cancel. It thinks the hardware has its enqueue pointer
somewhere further up in the ring, and thinks it's safe to turn the control
TRBs into no-op TRBs. Since the hardware was in the middle of the control
TRBs to be cancelled, the proper software behavior is to issue a Set TR
dequeue pointer command.
It turns out that the NEC host controllers can handle active TRBs being
set to no-op TRBs after a stop endpoint command, but other host
controllers have issues with this out-of-spec software behavior. Fix this
behavior.
This patch should be backported to kernels as far back as 2.6.31, but it
may be a bit challenging, since process_ctrl_td() was introduced in some
refactoring done in 2.6.36, and some endian-safe patches added in 2.6.40
that touch the same lines.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: stable@kernel.org
The error processing order was wrong.
This patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It was necessary to check pipe condition after disable fifo.
Current driver checked it in a wrong place.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Droids MuIn LCD operates like a serial remote terminal.
Data received are displayed directly on the LCD. This patch
fixes the kernel null pointer oops when it is plugged in.
Add NO_DATA_INTERFACE quirk to tell the driver that "control"
and "data" interfaces are not separated for this device, which
prevents dereferencing a null pointer in the device probe code.
Signed-off-by: Erik Slagter <erik@slagter.name>
Signed-off-by: Maxin B. John <maxin.john@gmail.com>
Tested-by: Erik Slagter <erik@slagter.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Samsung's S3C2416, S3C2443 and S3C2450 includes a USB High-Speed
device controller module. This driver enables support for USB high-speed
gadget functionality for the Samsung S3C24xx SoC's that include this
controller.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Alexander Neumann <alexander@bumpern.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Comparing an unsigned integer with greater than or equal to zero is
always true. So, it is safe to remove similar checks from
'f_mass_storage.c' and 'file_storage.c'
Signed-off-by: Maxin B. John <maxin.john@gmail.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On amd64 unsigned is not as wide as pointer and this causes a compiler
warning. Switching to unsigned long corrects the problem.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The __devinit and __devexit macros were added to probe and remove
functions. The macros move the probe and remove functions to the
devinit and devexit sections
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Defer the SET_CONFIG and SET_INTERFACE control transfer's data/status
stages till we are ready to process new CBW from the host. This way we
ensure that we don't loose any CBW during MSC compliance tests and cause
lock up.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some USB function drivers (e.g. f_mass_storage.c) need to delay or defer the
data/status stages of standard control requests like SET_CONFIGURATION or
SET_INTERFACE till they are done with their bookkeeping and are actually ready
for accepting new commands to their interface.
They can now achieve this functionality by returning USB_GADGET_DELAYED_STATUS
in their setup handlers (e.g. set_alt()). The composite framework will then
defer completion of the control transfer by not completing the data/status stages.
This ensures that the host does not send new packets to the interface till the
function driver is ready to take them.
When the function driver that requested for USB_GADGET_DELAYED_STATUS is done
with its bookkeeping, it should signal the composite framework to continue with
the data/status stages of the control transfer. It can do so by invoking
the new API usb_composite_setup_continue(). This is where the control transfer's
data/status stages are completed and host can initiate new transfers.
The DELAYED_STATUS mechanism is currently only supported if the expected data phase
is 0 bytes (i.e. w_length == 0). Since SET_CONFIGURATION and SET_INTERFACE are the
only cases that will use this mechanism, this is not a limitation.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-next' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
xHCI 1.0: Max Exit Latency Too Large Error
xHCI 1.0: TT_THINK_TIME set
xHCI 1.0: Block Interrupts for Isoch transfer
xHCI 1.0: Isoch endpoint CErr field set
xHCI 1.0: Control endpoint average TRB length field set
xHCI 1.0: Setup Stage TRB Transfer Type flag
This is a new TRB Completion Code of the xHCI spec 1.0.
Asserted by the Evalute Context Command if the proposed Max Exit Latency would
not allow the periodic endpoints of the Device Slot to be scheduled.
Signed-off-by: Alex He <alex.he@amd.com>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xHCI 1.0 spec says the TT Think Time field shall be set to zero if the device
is not a High-speed hub.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Currently an isoc URB is divided into multiple TDs, and every TD will
trigger an interrupt when it's processed. However, software can schedule
multiple TDs at a time, and it only needs an interrupt every URB.
xHCI 1.0 introduces the Block Event Interrupt(BEI) flag which allows Normal
and Isoch Transfer TRBs to place an Event TRB on an Event Ring but not
assert an intrrupt to the host, and the interrupt rate is significantly
reduced and the system performance is improved.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xHCI 1.0 specification specifies that CErr does not apply to Isoch endpoints
and shall be set to '0' for Isoch endpoints.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xHCI 1.0 specification indicates that software should set Average TRB Length
to '8' for control endpoints.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Setup Stage Transfer Type field is added to indicate the presence and the
direction of the Data Stage TD, and determines the direction of the Status
Stage TD so the wLength length field should be ignored by the xHC.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Implement good battery algorithm defined in the battery charging V1.2 spec
for detecting different charging ports. USB hardware is put into low power
mode when connected to a dedicated charging port. vbus_draw and set_power
methods are implemented for determining the allowed current from Host in
different states (un-configured/suspend/configured).
The charger block is implemented using vendor specific registers and the
PHY used in MSM8960(28nm PHY) different from older targets like MSM8x60
and MSM7x30(45nm PHY). The PHY vendor and product id registers are not
implemented in the above chipsets. Hence PHY type is passed via platform
data.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
HSUSB core clock is derived from daytona fabric clock and for
HSUSB operational require minimum core clock at 55MHz. Since, HSUSB
cannot tolerate daytona fabric clock change in the middle of HSUSB
operational, vote for maximum Daytona fabric clock
while usb is operational
Signed-off-by: Anji jonnala <anjir@codeaurora.org>
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the UHCI part of the GRLIB GRUSBHC controller
found on some LEON/GRLIB SoCs.
The UHCI HCD previously only supported controllers connected over PCI.
This patch adds support for the first non-PCI UHCI HC. I have tried to
replicate the solution used in ehci-hcd.c.
Tested on GR-LEON4-ITX board (LEON4/GRLIB with GRUSBHC) and x86 with Intel
UHCI HC.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is part of a series that extend the UHCI HCD to support
non-PCI host controllers.
This patch also extends the uhci_{read,write}* functions to allow accesses
to registers not mapped into PCI I/O space. This extension also includes
the addition of a void __iomem pointer to the uhci structure.
A new Kconfig option is added to signal that the system has a non-PCI HC.
If this Kconfig option is set, uhci-hcd.c will include generic reset functions
for systems that do not make use of keyboard and mouse legacy support. PCI
controllers will still always use the reset functions from pci-quirks
This patch is followed by a patch that adds bus glue for the first non-PCI
UHCI HC.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is part of a series that extend the UHCI HCD to support
non-PCI controllers.
This patch replaces in{b,w,l} and out{b,wl} with calls to local inline
functions. This is done so that the register access functions can be
extended to support register areas not mapped in PCI I/O space.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is part of a series that extend the UHCI HCD to support
non-PCI controllers.
This patch moves PCI specific functions to uhci-pci.c and includes
this file in uhci-hcd.c. It also renames the function uhci_init to
uhci_pci_init.
uhci_init/uhci_pci_init is modified so that the port-detection logic
is kept in a new separate function uhci_count_ports() in uhci-hcd.c.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is part of a series that extend the UHCI HCD to support
non-PCI host controllers.
This patch fixes the following warnings from checkpatch:
ERROR: switch and case should be at the same indent
+ switch (to_pci_dev(uhci_dev(uhci))->vendor) {
+ default:
[...]
+ case PCI_VENDOR_ID_GENESYS:
[...]
+ case PCI_VENDOR_ID_INTEL:
WARNING: static char array declaration should probably be static const char
+ static char bad_Asus_board[] = "A7V8X";
WARNING: Use DEFINE_PCI_DEVICE_TABLE for struct pci_device_id
+static const struct pci_device_id uhci_pci_ids[] = { {
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is part of a series that extend the UHCI HCD to support
non-PCI controllers.
This patch changes calls to uhci_reset_hc, uhci_check_and_reset_hc,
configure_hc, resume_detect_interrupts_are_broken and
global_suspend_mode_is_broken so that they are made through pointers
in the uhci hcd struct. This will allow these functions to be replaced
with bus/arch specific functions.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is part of a series that extend the UHCI HCD to support
non-PCI host controllers.
uhci-hub.c contained two PCI vendor checks for silicon quirks. Move
these checks into uhci-hcd.c and use bits in uhci_hcd structure to
mark that we need to use the quirks.
This patch is followed by other patches that will remove PCI
dependencies from uhci-hcd.c as well.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Though USB controller works without this most of the time, an issue was faced
where USB was configured as printer device and it was dropping first
packet(64 bytes) in full speed mode due to DATA PID mismatch.
The problem gets resolved once unused endpoints are configured as bulk.
As per P1020 RM (Table17-31, bits 19-18, bits 3-2) "When only one endpoint
(RX or TX, but not both) of an endpoint pair is used, the unused endpoint
should be configured as a bulk type endpoint." So according to the RM,
this patch is initializing TX and RX endpoints as bulk type
Signed-off-by: Suchit Lepcha <Suchit.Lepcha@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the checkpatch errors ans warnings listed below:
ERROR: do not use assignment in if condition
WARNING: line over 80 characters
WARNING: braces {} are not necessary for single statement blocks
WARNING: space prohibited between function name and open parenthesis '('
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove a stray 'return 0' at the top of the suspend callback,
and move au1xxx_stop_ehc() out of the ehci spinlock since it takes
some time to complete.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 3dacdf11 "usb: factor out state_string() on otg drivers"
broke building musb drivers since there is already another
otg_state_string() function in musb drivers, but with different
prototype. Fix musb drivers to use common otg_state_string(), too.
Also provide a nop for otg_state_string() if CONFIG_USB_OTG_UTILS
is not defined.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Saves about 50KB of data.
Old/new size of all objects:
text data bss dec hex filename
563015 80096 130684 773795 bcea3 (TOTALS)
610916 32256 130632 773804 bceac (TOTALS)
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be> (for drivers/net/can/softing/softing_cs.c)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch adds support for the GRLIB GRUSBHC EHCI controller from
Aeroflex Gaisler. The controller is typically found on LEON/GRLIB
SoCs.
Tested on GR-LEON4-ITX with with little endian interface and on
LEON3 system on GR-PCI-XC5V development board for big endian
controller.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The two first HC capability registers (CAPLENGTH and HCIVERSION)
are defined as one 8-bit and one 16-bit register. Most HC
implementations have selected to treat these registers as part
of a 32-bit register, giving the same layout for both big and
small endian systems.
This patch adds a new quirk, big_endian_capbase, to support
controllers with big endian register interfaces that treat
HCIVERSION and CAPLENGTH as individual registers.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch clears PORT_PLC if xhci_bus_resume() resumes a previous suspended
port, because if a port transition from U3 to U0 state, it will report a
port link state change, and software should clear the corresponding PLC bit.
It also uses hcd->speed to check if a port is a USB2 protocol port.
The patch fixes the issue that USB keyboard can not wakeup system from
hibernation.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The current code is clearing in_lpm flag after enabling the IRQ.
If IRQ comes immediately before in_lpm flag is set, it thinks that
hardware is in low power mode and disables the IRQ. Fix this by
clearing in_lpm flag before enabling the IRQ.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
