To avoid confusion with the recently deleted fib_hash.c
code, use "fib_info_hash_*" instead of plain "fib_hash_*".
Signed-off-by: David S. Miller <davem@davemloft.net>
The time has finally come to remove the hash based routing table
implementation in ipv4.
FIB Trie is mature, well tested, and I've done an audit of it's code
to confirm that it implements insert, delete, and lookup with the same
identical semantics as fib_hash did.
If there are any semantic differences found in fib_trie, we should
simply fix them.
I've placed the trie statistic config option under advanced router
configuration.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Move all shared mem code to bnx2x to avoid code duplication. bnx2x now
performs:
- Read the FCoE and iSCSI max connection information.
- Read the iSCSI and FCoE MACs from NPAR configuration in shmem.
- Block the CNIC for the current function if there is neither FCoE nor
iSCSI valid configuration by returning NULL from bnx2x_cnic_probe().
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both fib_trie and fib_hash have a local implementation of
fib_table_select_default(). This is completely unnecessary
code duplication.
Since we now remember the fib_table and the head of the fib
alias list of the default route, we can implement one single
generic version of this routine.
Looking at the fib_hash implementation you may get the impression
that it's possible for there to be multiple top-level routes in
the table for the default route. The truth is, it isn't, the
insert code will only allow one entry to exist in the zero
prefix hash table, because all keys evaluate to zero and all
keys in a hash table must be unique.
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used later to implement fib_select_default() in a
completely generic manner, instead of the current situation where the
default route is re-looked up in the TRIE/HASH table and then the
available aliases are analyzed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bnx2x version to 1.62.11-0
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded support for emulation/FPGA from the code
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CMS(Common Mode Sense) functionality for 848x3 as this reduces power consumption and allows a better 10G link stability
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for new PHY BCM84833. This PHY is very similar to the BCM84823, only it has different register offset compared to the BCM84823, which needs to be handled correctly.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flexible support to control various SFP+ module features either throughout MDIO registers or GPIO pins according to NVRAM configuration
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and modify some net dev prints to improve error control
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix annoying compilation warning, mainly related to static declarations
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains cosmetic changes only of restyling comments according to Linux coding standard, and add comment for get_emac_base function.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains cosmetic changes only of renaming CL45_WR_OVER_CL22 macro to CL22_WR_OVER_CL45 as it should be.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains cosmetic changes only to fix code alignment, and update copyright comment year
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
batman_skb_recv can be defined in hard-interface.c as static because it is
never used outside of that file.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Some function parameters are obsolete now and can be removed.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The routing algorithm must be able to decide if a fragment can be merged with
the missing part and still be passed to a forwarding interface. The fragments
can only differ by one byte in case that the original payload had an uneven
length. In that situation the sender has to inform all possible receivers that
the tail is one byte longer using the flag UNI_FRAG_LARGETAIL.
The combination of UNI_FRAG_LARGETAIL and UNI_FRAG_HEAD flag makes it possible
to calculate the correct length for even and uneven sized payloads.
The original formula missed to add the unicast header at all and forgot to
remove the fragment header of the second fragment. This made the results highly
unreliable and only useful for machines with large differences between the
configured MTUs.
Reported-by: Russell Senior <russell@personaltelco.net>
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The routing algorithm must know how large two fragments are to be able to
decide that it is safe to merge them or if it should resubmit without waiting
for the second part. When these two fragments have a too different size, it is
not possible to guess right in every situation.
The user could easily configure the MTU of the attached cards so that one
fragment is forwarded and the other one is added to the fragments table to wait
for the missing part.
For even sized packets, it is possible to split it so that the resulting
packages are equal sized by ignoring the old non-fragment header at the
beginning of the original packet.
This still creates different sized fragments for uneven sized packets.
Reported-by: Russell Senior <russell@personaltelco.net>
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Update bnx2x version to 1.62.00-5
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All functions on a port should be set to take the MDC/MDIO lock to avoid contention on the bus
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix link on BCM57712 + BCM8073 when port swap is enabled. Common PHY reset was done on the wrong port.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix blink rate of activity LED of the BCM84823 on 10G link
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A rare link issue with the BCM8073 PHY may occur due to setting XAUI low power mode, while the PHY microcode already does that.
The fix is not to set set XAUI low power mode for this PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The batman-adv vis server has to a stack which stores all information
about packets which should be send later. This stack is protected
with a spinlock that is used to prevent concurrent write access to it.
The send_vis_packets function has to take all elements from the stack
and send them to other hosts over the primary interface. The send will
be initiated without the lock which protects the stack.
The implementation using list_for_each_entry_safe has the problem that
it stores the next element as "safe ptr" to allow the deletion of the
current element in the list. The list may be modified during the
unlock/lock pair in the loop body which may make the safe pointer
not pointing to correct next element.
It is safer to remove and use the first element from the stack until no
elements are available. This does not need reduntant information which
would have to be validated each time the lock was removed.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The free_info function will be called when no reference to the info
object exists anymore. It must be ensured that the allocated memory
gets freed and not only the elements which are managed by the info
object.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
A newly created vis info object must be removed when it couldn't be
added to the hash. The old_info which has to be replaced was already
removed and isn't related to the hash anymore.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
SIOCGETSGCNT is not a unique ioctl value as it it maps tio SIOCPROTOPRIVATE +1,
which unfortunately means the existing infrastructure for compat networking
ioctls is insufficient. A trivial compact ioctl implementation would conflict
with:
SIOCAX25ADDUID
SIOCAIPXPRISLT
SIOCGETSGCNT_IN6
SIOCGETSGCNT
SIOCRSSCAUSE
SIOCX25SSUBSCRIP
SIOCX25SDTEFACILITIES
To make this work I have updated the compat_ioctl decode path to mirror the
the normal ioctl decode path. I have added an ipv4 inet_compat_ioctl function
so that I can have ipv4 specific compat ioctls. I have added a compat_ioctl
function into struct proto so I can break out ioctls by which kind of ip socket
I am using. I have added a compat_raw_ioctl function because SIOCGETSGCNT only
works on raw sockets. I have added a ipmr_compat_ioctl that mirrors the normal
ipmr_ioctl.
This was necessary because unfortunately the struct layout for the SIOCGETSGCNT
has unsigned longs in it so changes between 32bit and 64bit kernels.
This change was sufficient to run a 32bit ip multicast routing daemon on a
64bit kernel.
Reported-by: Bill Fenner <fenner@aristanetworks.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add caif_socket.h and if_caif.h to the kernel header files
exported for use by userspace.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the referenced project website to www.mictronics.de in the Kconfig
help text for the slcan driver.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On older kernels the VLAN code may zero skb->dev before dropping
it and causing it to be reused by GRO.
Unfortunately we didn't reset skb->dev in that case which causes
the next GRO user to get a bogus skb->dev pointer.
This particular problem no longer happens with the current upstream
kernel due to changes in VLAN processing.
However, for correctness we should still reset the skb->dev pointer
in the GRO reuse function in case a future user does the same thing.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib metric memory in this case is static in the kernel image,
so we don't need to reference count it since it's never going
to go away on us.
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are no explicit metrics attached to a route, hook
fi->fib_info up to dst_default_metrics.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the initial gateway towards super-sharing metrics
if they are all set to zero for a route.
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP is going to record metrics for the connection,
so pre-COW the route metrics at route cache entry
creation time.
This avoids several atomic operations that have to
occur if we COW the metrics after the entry reaches
global visibility.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use net_device_stats instance from the struct net_device.
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing __rcu annotations and helpers.
minor : Fix some rcu_dereference() calls in macvtap
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>