* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix header export, asm-x86/processor-flags.h, CONFIG_* leaks
x86: BUILD_IRQ say .text to avoid .data.percpu
xen: don't use sysret for sysexit32
x86: call early_cpu_init at the same point
This fixes kernel http://bugzilla.kernel.org/show_bug.cgi?id=11112 (bogus
RTC update IRQs reported) for rtc-cmos, in two ways:
- When HPET is stealing the IRQs, use the first IRQ to grab
the seconds counter which will be monitored (instead of
using whatever was previously in that memory);
- In sane IRQ handling modes, scrub out old IRQ status before
enabling IRQs.
That latter is done by tightening up IRQ handling for rtc-cmos everywhere,
also ensuring that when HPET is used it's the only thing triggering IRQ
reports to userspace; net object shrink.
Also fix a bogus HPET message related to its RTC emulation.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Report-by: W Unruh <unruh@physics.ubc.ca>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces the new syscall inotify_init1 (note: the 1 stands for
the one parameter the syscall takes, as opposed to no parameter before). The
values accepted for this parameter are function-specific and defined in the
inotify.h header. Here the values must match the O_* flags, though. In this
patch CLOEXEC support is introduced.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_inotify_init1
# ifdef __x86_64__
# define __NR_inotify_init1 294
# elif defined __i386__
# define __NR_inotify_init1 332
# else
# error "need __NR_inotify_init1"
# endif
#endif
#define IN_CLOEXEC O_CLOEXEC
int
main (void)
{
int fd;
fd = syscall (__NR_inotify_init1, 0);
if (fd == -1)
{
puts ("inotify_init1(0) failed");
return 1;
}
int coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
puts ("inotify_init1(0) set close-on-exit");
return 1;
}
close (fd);
fd = syscall (__NR_inotify_init1, IN_CLOEXEC);
if (fd == -1)
{
puts ("inotify_init1(IN_CLOEXEC) failed");
return 1;
}
coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
puts ("inotify_init1(O_CLOEXEC) does not set close-on-exit");
return 1;
}
close (fd);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[akpm@linux-foundation.org: add sys_ni stub]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces the new syscall pipe2 which is like pipe but it also
takes an additional parameter which takes a flag value. This patch implements
the handling of O_CLOEXEC for the flag. I did not add support for the new
syscall for the architectures which have a special sys_pipe implementation. I
think the maintainers of those archs have the chance to go with the unified
implementation but that's up to them.
The implementation introduces do_pipe_flags. I did that instead of changing
all callers of do_pipe because some of the callers are written in assembler.
I would probably screw up changing the assembly code. To avoid breaking code
do_pipe is now a small wrapper around do_pipe_flags. Once all callers are
changed over to do_pipe_flags the old do_pipe function can be removed.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_pipe2
# ifdef __x86_64__
# define __NR_pipe2 293
# elif defined __i386__
# define __NR_pipe2 331
# else
# error "need __NR_pipe2"
# endif
#endif
int
main (void)
{
int fd[2];
if (syscall (__NR_pipe2, fd, 0) != 0)
{
puts ("pipe2(0) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
int coe = fcntl (fd[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
printf ("pipe2(0) set close-on-exit for fd[%d]\n", i);
return 1;
}
}
close (fd[0]);
close (fd[1]);
if (syscall (__NR_pipe2, fd, O_CLOEXEC) != 0)
{
puts ("pipe2(O_CLOEXEC) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
int coe = fcntl (fd[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
printf ("pipe2(O_CLOEXEC) does not set close-on-exit for fd[%d]\n", i);
return 1;
}
}
close (fd[0]);
close (fd[1]);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the new dup3 syscall. It extends the old dup2 syscall by one
parameter which is meant to hold a flag value. Support for the O_CLOEXEC flag
is added in this patch.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <time.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_dup3
# ifdef __x86_64__
# define __NR_dup3 292
# elif defined __i386__
# define __NR_dup3 330
# else
# error "need __NR_dup3"
# endif
#endif
int
main (void)
{
int fd = syscall (__NR_dup3, 1, 4, 0);
if (fd == -1)
{
puts ("dup3(0) failed");
return 1;
}
int coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
puts ("dup3(0) set close-on-exec flag");
return 1;
}
close (fd);
fd = syscall (__NR_dup3, 1, 4, O_CLOEXEC);
if (fd == -1)
{
puts ("dup3(O_CLOEXEC) failed");
return 1;
}
coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
puts ("dup3(O_CLOEXEC) set close-on-exec flag");
return 1;
}
close (fd);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the new epoll_create2 syscall. It extends the old epoll_create
syscall by one parameter which is meant to hold a flag value. In this
patch the only flag support is EPOLL_CLOEXEC which causes the close-on-exec
flag for the returned file descriptor to be set.
A new name EPOLL_CLOEXEC is introduced which in this implementation must
have the same value as O_CLOEXEC.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <time.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_epoll_create2
# ifdef __x86_64__
# define __NR_epoll_create2 291
# elif defined __i386__
# define __NR_epoll_create2 329
# else
# error "need __NR_epoll_create2"
# endif
#endif
#define EPOLL_CLOEXEC O_CLOEXEC
int
main (void)
{
int fd = syscall (__NR_epoll_create2, 1, 0);
if (fd == -1)
{
puts ("epoll_create2(0) failed");
return 1;
}
int coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
puts ("epoll_create2(0) set close-on-exec flag");
return 1;
}
close (fd);
fd = syscall (__NR_epoll_create2, 1, EPOLL_CLOEXEC);
if (fd == -1)
{
puts ("epoll_create2(EPOLL_CLOEXEC) failed");
return 1;
}
coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
puts ("epoll_create2(EPOLL_CLOEXEC) set close-on-exec flag");
return 1;
}
close (fd);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the new eventfd2 syscall. It extends the old eventfd
syscall by one parameter which is meant to hold a flag value. In this
patch the only flag support is EFD_CLOEXEC which causes the close-on-exec
flag for the returned file descriptor to be set.
A new name EFD_CLOEXEC is introduced which in this implementation must
have the same value as O_CLOEXEC.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_eventfd2
# ifdef __x86_64__
# define __NR_eventfd2 290
# elif defined __i386__
# define __NR_eventfd2 328
# else
# error "need __NR_eventfd2"
# endif
#endif
#define EFD_CLOEXEC O_CLOEXEC
int
main (void)
{
int fd = syscall (__NR_eventfd2, 1, 0);
if (fd == -1)
{
puts ("eventfd2(0) failed");
return 1;
}
int coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
puts ("eventfd2(0) sets close-on-exec flag");
return 1;
}
close (fd);
fd = syscall (__NR_eventfd2, 1, EFD_CLOEXEC);
if (fd == -1)
{
puts ("eventfd2(EFD_CLOEXEC) failed");
return 1;
}
coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
puts ("eventfd2(EFD_CLOEXEC) does not set close-on-exec flag");
return 1;
}
close (fd);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[akpm@linux-foundation.org: add sys_ni stub]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the new signalfd4 syscall. It extends the old signalfd
syscall by one parameter which is meant to hold a flag value. In this
patch the only flag support is SFD_CLOEXEC which causes the close-on-exec
flag for the returned file descriptor to be set.
A new name SFD_CLOEXEC is introduced which in this implementation must
have the same value as O_CLOEXEC.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <signal.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_signalfd4
# ifdef __x86_64__
# define __NR_signalfd4 289
# elif defined __i386__
# define __NR_signalfd4 327
# else
# error "need __NR_signalfd4"
# endif
#endif
#define SFD_CLOEXEC O_CLOEXEC
int
main (void)
{
sigset_t ss;
sigemptyset (&ss);
sigaddset (&ss, SIGUSR1);
int fd = syscall (__NR_signalfd4, -1, &ss, 8, 0);
if (fd == -1)
{
puts ("signalfd4(0) failed");
return 1;
}
int coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
puts ("signalfd4(0) set close-on-exec flag");
return 1;
}
close (fd);
fd = syscall (__NR_signalfd4, -1, &ss, 8, SFD_CLOEXEC);
if (fd == -1)
{
puts ("signalfd4(SFD_CLOEXEC) failed");
return 1;
}
coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
puts ("signalfd4(SFD_CLOEXEC) does not set close-on-exec flag");
return 1;
}
close (fd);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[akpm@linux-foundation.org: add sys_ni stub]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACPI defines a hardware signature. BIOS calculates the signature according to
hardware configure and if hardware changes while hibernated, the signature
will change. In that case, S4 resume should fail.
Still, there may be systems on which this mechanism does not work correctly,
so it is better to provide a workaround for them. For this reason, add a new
switch to the acpi_sleep= command line argument allowing one to disable
hardware signature checking.
[shaohua.li@intel.com: build fix]
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <Valdis.Kletnieks@vt.edu>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the obsolete and no longer used include/linux/pm_legacy.h
Reviewed-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Pavel Machek <pavel@suse.cz>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On 32-bit architectures PAGE_ALIGN() truncates 64-bit values to the 32-bit
boundary. For example:
u64 val = PAGE_ALIGN(size);
always returns a value < 4GB even if size is greater than 4GB.
The problem resides in PAGE_MASK definition (from include/asm-x86/page.h for
example):
#define PAGE_SHIFT 12
#define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT)
#define PAGE_MASK (~(PAGE_SIZE-1))
...
#define PAGE_ALIGN(addr) (((addr)+PAGE_SIZE-1)&PAGE_MASK)
The "~" is performed on a 32-bit value, so everything in "and" with
PAGE_MASK greater than 4GB will be truncated to the 32-bit boundary.
Using the ALIGN() macro seems to be the right way, because it uses
typeof(addr) for the mask.
Also move the PAGE_ALIGN() definitions out of include/asm-*/page.h in
include/linux/mm.h.
See also lkml discussion: http://lkml.org/lkml/2008/6/11/237
[akpm@linux-foundation.org: fix drivers/media/video/uvc/uvc_queue.c]
[akpm@linux-foundation.org: fix v850]
[akpm@linux-foundation.org: fix powerpc]
[akpm@linux-foundation.org: fix arm]
[akpm@linux-foundation.org: fix mips]
[akpm@linux-foundation.org: fix drivers/media/video/pvrusb2/pvrusb2-dvb.c]
[akpm@linux-foundation.org: fix drivers/mtd/maps/uclinux.c]
[akpm@linux-foundation.org: fix powerpc]
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
it is for uv only
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When I edit the x86_64 Makefile to -fno-unit-at-a-time, bootup panics
on 0xCCs in IRQ0x3e_interrupt(): IRQ0x20_interrupt etc. have got linked
into .data.percpu. Perhaps there are other ways of triggering that:
specify ".text" in the BUILD_IRQ() macro for safety.
I've been using -fno-unit-at-a-time (to lessen inlining, for easier
debugging) for a long time.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Dump all the PIC, local APIC and I/O APIC information at the
fs_initcall() level, which is after ACPI (if used) has initialised PCI
information, making the point of invocation consistent across MP-table and
ACPI platforms. Remove explicit calls to print_IO_APIC() from elsewhere.
Make the interface of all the functions involved consistent between 32-bit
and 64-bit versions and make them all static by default by the means of a
New-and-Improved(TM) __apicdebuginit() macro.
Note that like print_IO_APIC() all these only output anything if
"apic=debug" has been passed to the kernel through the command line.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The CFI_ADJUST_CFA_OFFSET dwarf2 annotation of a push/popf
pair in ret_from_fork wrongly used a value of 4. It should
have been 8. Fix that.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: heukelum@fastmail.fm
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Call early_cpu_init() at the same (early) point in setup_arch().
The x86_64 code was calling it relatively late, after when other arch
code need to do cpu-related setup which depends on it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'sched/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: hrtick_enabled() should use cpu_active()
sched, x86: clean up hrtick implementation
sched: fix build error, provide partition_sched_domains() unconditionally
sched: fix warning in inc_rt_tasks() to not declare variable 'rq' if it's not needed
cpu hotplug: Make cpu_active_map synchronization dependency clear
cpu hotplug, sched: Introduce cpu_active_map and redo sched domain managment (take 2)
sched: rework of "prioritize non-migratable tasks over migratable ones"
sched: reduce stack size in isolated_cpu_setup()
Revert parts of "ftrace: do not trace scheduler functions"
Fixed up conflicts in include/asm-x86/thread_info.h (due to the
TIF_SINGLESTEP unification vs TIF_HRTICK_RESCHED removal) and
kernel/sched_fair.c (due to cpu_active_map vs for_each_cpu_mask_nr()
introduction).
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
cpumask: Provide a generic set of CPUMASK_ALLOC macros
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
Revert "cpumask: introduce new APIs"
cpumask: make for_each_cpu_mask a bit smaller
net: Pass reference to cpumask variable in net/sunrpc/svc.c
...
Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually
This adds fast paths for 32-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
These paths does not need to save and restore all registers as
the general case of tracing does. Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Signed-off-by: Roland McGrath <roland@redhat.com>
This adds fast paths for 32-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
These paths does not need to save and restore all registers as
the general case of tracing does. Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Signed-off-by: Roland McGrath <roland@redhat.com>
This adds a fast path for 64-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
This path does not need to save and restore all registers as
the general case of tracing does. Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Signed-off-by: Roland McGrath <roland@redhat.com>
This short-circuit path in sysret_signal looks wrong to me.
AFAICT, in practice the branch is never taken--and if it were,
it would go wrong. To wit, try loading a module whose init
function does set_thread_flag(TIF_IRET), and see insmod crash
(presumably with a wrong user stack pointer).
This is because the FIXUP_TOP_OF_STACK work hasn't been done yet
when we jump around the call to ptregscall_common and get to
int_with_check--where it expects the user RSP,SS,CS and EFLAGS to
have been stored by FIXUP_TOP_OF_STACK.
I don't think it's normally possible to get to sysret_signal with no
_TIF_DO_NOTIFY_MASK bits set anyway, so these two instructions are
already superfluous. If it ever did happen, it is harmless to call
do_notify_resume with nothing for it to do.
Signed-off-by: Roland McGrath <roland@redhat.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix crash due to missing debugctlmsr on AMD K6-3
x86: add PTE_FLAGS_MASK
x86: rename PTE_MASK to PTE_PFN_MASK
x86: fix pte_flags() to only return flags, fix lguest (updated)
x86: use setup_clear_cpu_cap with disable_apic, fix
x86: move the last Dprintk instance to pr_debug()
This patch consolidates the header guard names which are also used
externally, i.e. in .c files.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Declare time_init() in asm-x86/time.h
Also did cleanup in asm-x86/timer.h :
timer_ack is only required for X86_32
int recalibrate_cpu_khz(void) is for X86_32
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Moved DECLARE_PER_CPU(int, cpu_number) from CONFIG_X86_32_SMP to CONFIG_X86_32
because cpu_number is required for both.
And include asm/smp.h in process_32.c
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
(Jeremy said:
rusty: use PTE_MASK
rusty: use PTE_MASK
rusty: use PTE_MASK
When I asked:
jsgf: does that include the NX flag?
He responded eloquently:
rusty: use PTE_MASK
rusty: use PTE_MASK
yes, it's the official constant of masking flags out of ptes
)
Change a15af1c9ea 'x86/paravirt: add
pte_flags to just get pte flags' removed lguest's private pte_flags()
in favor of a generic one.
Unfortunately, the generic one doesn't filter out the non-flags bits:
this results in lguest creating corrupt shadow page tables and blowing
up host memory.
Since noone is supposed to use the pfn part of pte_flags(), it seems
safest to always do the filtering.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-and-morning-tea-spilled-by: Ingo Molnar <mingo@elte.hu>
introducing an APIC handling probing abstraction:
static struct genapic *apic_probe[] __initdata = {
&apic_x2apic_uv_x,
&apic_x2apic_phys,
&apic_x2apic_cluster,
&apic_physflat,
NULL,
};
This way we can remove UV, x2apic specific code from genapic_64.c and
move them to their specific genapic files.
[ v2: fix compiling when CONFIG_ACPI is not set ]
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
beauty fix: /proc/cpuinfo will still show apic feature even if
we booted up with it disabled.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use the new generic int attribute accessors for the x86 mce tolerant
attribute. Simple example to illustrate the new macros.
There are much more places all over the tree that could be converted
like this.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allow to dynamically generate attributes and share show/store
functions between attributes. Right now most attributes are generated
by special macros and lots of duplicated code. With the attribute
passed it's instead possible to attach some data to the attribute
and then use that in shared low level functions to do different things.
I need this for the dynamically generated bank attributes in the x86
machine check code, but it'll allow some further cleanups.
I converted all users in tree to the new show/store prototype. It's a single
huge patch to avoid unbisectable sections.
Runtime tested: x86-32, x86-64
Compiled only: ia64, powerpc
Not compile tested/only grep converted: sh, arm, avr32
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have the dev_printk() variants for this kind of thing, use them
instead of directly trying to access the bus_id field of struct device.
This is done in order to remove bus_id entirely.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are a couple of places where (P)Dprintk is used which is an old
compile time enabled printk wrapper. Convert it to the generic
pr_debug().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
... so don't need to call clear_cpu_cap again in early_identify_cpu,
and could use cleared_cpu_caps like other places.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch makes the needlessly global kvm_smp_prepare_boot_cpu() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Avi Kivity <avi@qumranet.com>
random uvesafb failures were reported against Gentoo:
http://bugs.gentoo.org/show_bug.cgi?id=222799
and Mihai Moldovan bisected it back to:
> 8f4d37ec07 is first bad commit
> commit 8f4d37ec07
> Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
> Date: Fri Jan 25 21:08:29 2008 +0100
>
> sched: high-res preemption tick
Linus suspected it to be hrtick + vm86 interaction and observed:
> Btw, Peter, Ingo: I think that commit is doing bad things. They aren't
> _incorrect_ per se, but they are definitely bad.
>
> Why?
>
> Using random _TIF_WORK_MASK flags is really impolite for doing
> "scheduling" work. There's a reason that arch/x86/kernel/entry_32.S
> special-cases the _TIF_NEED_RESCHED flag: we don't want to exit out of
> vm86 mode unnecessarily.
>
> See the "work_notifysig_v86" label, and how it does that
> "save_v86_state()" thing etc etc.
Right, I never liked having to fiddle with those TIF flags. Initially I
needed it because the hrtimer base lock could not nest in the rq lock.
That however is fixed these days.
Currently the only reason left to fiddle with the TIF flags is remote
wakeups. We cannot program a remote cpu's hrtimer. I've been thinking
about using the new and improved IPI function call stuff to implement
hrtimer_start_on().
However that does require that smp_call_function_single(.wait=0) works
from interrupt context - /me looks at the latest series from Jens - Yes
that does seem to be supported, good.
Here's a stab at cleaning this stuff up ...
Mihai reported test success as well.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Mihai Moldovan <ionic@ionic.de>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some cleanups in speedstep-centrino.c for NR_CPUS=4096.
* Use new CPUMASK_PTR (instead of old CPUMASK_VAR).
* Replace arrays sized by NR_CPUS with percpu variables.
* Cleanup some formatting problems (>80 chars per line)
and other checkpatch complaints.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* nr_cpu_ids should be used to determine if a percpu area is
available for a given cpu.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Replace NR_CPUS loop with for_each_possible_cpu().
* nr_cpu_ids should be used to determine if a percpu area is
available for a given cpu.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Use nr_cpu_ids instead of NR_CPUS to limit traversal of cpu online map.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* nr_cpu_ids should be used to allocate arrays based on the number of
cpu's present.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It's not possible to enable the unknown_nmi_panic sysctl option
until init is run. It's useful to be able to panic the kernel
during boot too, this adds a parameter to enable this option.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so NUMAQ can use that to call numaq_pre_time_init()
This allows us to remove a NUMAQ special from arch/x86/kernel/setup.c.
(and paves the way to remove the NUMAQ subarch)
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
add these new x86_quirks methods:
int *mpc_record;
int (*mpc_apic_id)(struct mpc_config_processor *m);
void (*mpc_oem_bus_info)(struct mpc_config_bus *m, char *name);
void (*mpc_oem_pci_bus)(struct mpc_config_bus *m);
void (*smp_read_mpc_oem)(struct mp_config_oemtable *oemtable,
unsigned short oemsize);
... and move NUMAQ related mps table handling to numaq_32.c.
also move the call to smp_read_mpc_oem() to smp_read_mpc() directly.
Should not change functionality, albeit it would be nice to get it
tested on real NUMAQ as well ...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
introduce x86_quirks array of boot-time quirk methods.
No change in functionality intended.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Fri, Jul 18, 2008 at 02:03:48PM -0700, Ingo Molnar wrote:
>
> * Yinghai Lu <yhlu.kernel@gmail.com> wrote:
>
> > > git merge tip/x86/x2apic
> > CONFLICT (content): Merge conflict in arch/x86/kernel/Makefile
> > CONFLICT (content): Merge conflict in arch/x86/kernel/paravirt.c
> > CONFLICT (content): Merge conflict in arch/x86/kernel/smpboot.c
> > CONFLICT (content): Merge conflict in arch/x86/kernel/vmi_32.c
> > CONFLICT (content): Merge conflict in arch/x86/xen/enlighten.c
> > CONFLICT (content): Merge conflict in include/asm-x86/apic.h
> > CONFLICT (content): Merge conflict in include/asm-x86/paravirt.h
>
> that's due to the changes in tip/x86/apic and in tip/x86/uv.
>
> ok, i've just merged x86/apic into x86/x2apic and x86/uv as well, and
> pushed out the result.
>
> Note: it's a first raw merge and completely untested. It will now merge
> cleanly into tip/master. There are probably a few details missing.
Ingo, thanks for doing this. While I was testing my merge changes, you posted
yours... anyhow we need this piece, which is missing from your merge.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a directory for x86 arch under debugfs. Can be used to accumulate all
x86 specific debugfs files.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
It's not used anywhere outside its single referencing file.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
On a x86-64 machine (nothing special I could encounter) I had the problem that
crashkernel reservation with the usual "64M@16M" failed. While debugging that,
I encountered that dma32_reserve_bootmem() reserves a memory region which is in
that area.
Because dma32_reserve_bootmem() does not rely on a specific offset but
crashkernel does, it makes sense to move the dma32_reserve_bootmem()
reservation down a bit. I tested that patch and it works without problems. I
don't see any negative effects of that move, but maybe I oversaw something ...
While we strictly don't need that patch in 2.6.27 because we have the
automatic, dynamic offset detection, it makes sense to also include it here
because:
- it's easier to get it in -stable then,
- many people are still used to the 'crashkernel=...@16M' syntax,
- not everybody may be using a reloatable kernel.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: kexec@lists.infradead.org
Cc: vgoyal@redhat.com
Cc: akpm@linux-foundation.org
Cc: Bernhard Walle <bwalle@suse.de>
Cc: yhlu.kernel@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Use the CPUMASK_ALLOC macros in the centrino_target() function.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Optimize various places where a pointer to the cpumask_of_cpu value
will result in reducing stack pressure.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Optimize various places where a pointer to the cpumask_of_cpu value
will result in reducing stack pressure.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* This patch replaces the dangerous lvalue version of cpumask_of_cpu
with new cpumask_of_cpu_ptr macros. These are patterned after the
node_to_cpumask_ptr macros.
In general terms, if there is a cpumask_of_cpu_map[] then a pointer to
the cpumask_of_cpu_map[cpu] entry is used. The cpumask_of_cpu_map
is provided when there is a large NR_CPUS count, reducing
greatly the amount of code generated and stack space used for
cpumask_of_cpu(). The pointer to the cpumask_t value is needed for
calling set_cpus_allowed_ptr() to reduce the amount of stack space
needed to pass the cpumask_t value.
If there isn't a cpumask_of_cpu_map[], then a temporary variable is
declared and filled in with value from cpumask_of_cpu(cpu) as well as
a pointer variable pointing to this temporary variable. Afterwards,
the pointer is used to reference the cpumask value. The compiler
will optimize out the extra dereference through the pointer as well
as the stack space used for the pointer, resulting in identical code.
A good example of the orthogonal usages is in net/sunrpc/svc.c:
case SVC_POOL_PERCPU:
{
unsigned int cpu = m->pool_to[pidx];
cpumask_of_cpu_ptr(cpumask, cpu);
*oldmask = current->cpus_allowed;
set_cpus_allowed_ptr(current, cpumask);
return 1;
}
case SVC_POOL_PERNODE:
{
unsigned int node = m->pool_to[pidx];
node_to_cpumask_ptr(nodecpumask, node);
*oldmask = current->cpus_allowed;
set_cpus_allowed_ptr(current, nodecpumask);
return 1;
}
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This printk has a KERN_ facility level in the format string.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Declaring x86 traps under one hood.
Declaring x86 do_traps before defining them.
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The device<->iommu relationship has to be set from the information in the ACPI
table too. This patch adds this logic to the driver.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: iommu@lists.linux-foundation.org
Cc: bhavna.sarathy@amd.com
Cc: robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The force_mwait variable iss defined either in
arch/x86/kernel/cpu/amd.c or in arch/x86/kernel/setup_64.c, but it is
only initialized and used in arch/x86/kernel/process.c. This patch
moves the declaration to arch/x86/kernel/process.c.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: michael@free-electrons.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jack Ren and Eric Miao tracked down the following long standing
problem in the NOHZ code:
scheduler switch to idle task
enable interrupts
Window starts here
----> interrupt happens (does not set NEED_RESCHED)
irq_exit() stops the tick
----> interrupt happens (does set NEED_RESCHED)
return from schedule()
cpu_idle(): preempt_disable();
Window ends here
The interrupts can happen at any point inside the race window. The
first interrupt stops the tick, the second one causes the scheduler to
rerun and switch away from idle again and we end up with the tick
disabled.
The fact that it needs two interrupts where the first one does not set
NEED_RESCHED and the second one does made the bug obscure and extremly
hard to reproduce and analyse. Kudos to Jack and Eric.
Solution: Limit the NOHZ functionality to the idle loop to make sure
that we can not run into such a situation ever again.
cpu_idle()
{
preempt_disable();
while(1) {
tick_nohz_stop_sched_tick(1); <- tell NOHZ code that we
are in the idle loop
while (!need_resched())
halt();
tick_nohz_restart_sched_tick(); <- disables NOHZ mode
preempt_enable_no_resched();
schedule();
preempt_disable();
}
}
In hindsight we should have done this forever, but ...
/me grabs a large brown paperbag.
Debugged-by: Jack Ren <jack.ren@marvell.com>,
Debugged-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This avoids calling kobject_uevent() with cache_kobject that has
already been deallocated in an error path.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
i386 has show_trace_log_lvl and show_stack_log_lvl, allowing
traces to be emitted with log-level annotations. This patch
introduces them to x86_64, but log_lvl is only ever set to
an empty string. Output of traces is unchanged.
i386-chunk is whitespace-only.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make the diff between the traps_32.c and traps_64.c a bit smaller.
Change traps_32.c to look more like traps_64.c:
- move lock information to file scope
- split out oops_begin() and oops_end() from die()
- increment nest counter in oops_begin
Only whitespace change in traps_64.c
No functional changes intended.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Real-time code needs to know the number of cycles per second
on SGI UV. The information is provided via a run time BIOS
call. This patch provides the linux side of that interface.
This is the first of several run time BIOS calls to be defined
in uv/bios.h and bios_uv.c.
Note that BIOS_CALL() is just a stub for now. The bios
side is being worked on.
Signed-off-by: Russ Anderson <rja@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Following recent (and less so) issues with the 8254 timer when routed
through the I/O or local APIC, always report which configurations have
been tried and which one has been set up eventually. This is so that logs
posted by people for some other reason can be used as a cross-reference
when investigating any possible future problems.
The change unifies messages printed on 32-bit and 64-bit platforms and
adds trailing newlines (removes leading ones), so that proper log level
annotation can be used and any possible interspersed output will not cause
a mess.
I have chosen to use apic_printk(APIC_QUIET, ...) rather than printk(...)
so that the distinction of these messages is maintained making possible
future decisions about changes in this area easier. A change posted
separately making apic_verbosity unsigned removes any extra code that
would otherwise be generated as a result of this design decision.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As a microoptimisation, make apic_verbosity unsigned. This will make
apic_printk(APIC_QUIET, ...) expand into just printk(...) with the
surrounding condition and a reference to apic_verbosity removed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Include <asm/i8259.h> for i8259A_lock used in print_PIC() -- #if-0-ed out
by default. The 32-bit version gets it right already.
The plan is to enable this code with "apic=debug" eventually. This will
aid with debugging strange problems without the need to ask people to
apply patches.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce calibrate_APIC_clock so it could help in further 32/64bit
apic code merging.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: macro@linux-mips.org
Cc: yhlu.kernel@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use alternatives to select the workaround for the 11AP Pentium erratum
for the affected steppings on the fly rather than build time. Remove the
X86_GOOD_APIC configuration option and replace all the calls to
apic_write_around() with plain apic_write(), protecting accesses to the
ESR as appropriate due to the 3AP Pentium erratum. Remove
apic_read_around() and all its invocations altogether as not needed.
Remove apic_write_atomic() and all its implementing backends. The use of
ASM_OUTPUT2() is not strictly needed for input constraints, but I have
used it for readability's sake.
I had the feeling no one else was brave enough to do it, so I went ahead
and here it is. Verified by checking the generated assembly and tested
with both a 32-bit and a 64-bit configuration, also with the 11AP
"feature" forced on and verified with gdb on /proc/kcore to work as
expected (as an 11AP machines are quite hard to get hands on these days).
Some script complained about the use of "volatile", but apic_write() needs
it for the same reason and is effectively a replacement for writel(), so I
have disregarded it.
I am not sure what the policy wrt defconfig files is, they are generated
and there is risk of a conflict resulting from an unrelated change, so I
have left changes to them out. The option will get removed from them at
the next run.
Some testing with machines other than mine will be needed to avoid some
stupid mistake, but despite its volume, the change is not really that
intrusive, so I am fairly confident that because it works for me, it will
everywhere.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yinghai Lu noticed that arch/x86/kernel/smpcommon_32.c got
renamed to arch/x86/kernel/smpcommon.c but the old almost-empty
file stayed around. Zap it.
Reported-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge the GDT_ENTRY() macro between arch/x86/boot/pm.c and
arch/x86/kernel/acpi/sleep.c and put the new one in
<asm-x86/segment.h>.
While we're at it, correct the bitmasks for the limit and flags. The
new version relies on using ULL constants in order to cause type
promotion rather than explicit casts; this avoids having to include
<linux/types.h> in <asm-x86/segments.h>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix asm/e820.h for userspace inclusion
x86: fix numaq_tsc_disable
x86: fix kernel_physical_mapping_init() for large x86 systems
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ftrace: do not trace library functions
ftrace: do not trace scheduler functions
ftrace: fix lockup with MAXSMP
ftrace: fix merge buglet
fix:
arch/x86/kernel/numaq_32.c: In function ‘numaq_tsc_disable’:
arch/x86/kernel/numaq_32.c:99: warning: ‘return’ with a value, in function returning void
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
-tip testing found a bootup hang here:
initcall anon_inode_init+0x0/0x130 returned 0 after 0 msecs
calling acpi_event_init+0x0/0x57
the bootup should have continued with:
initcall acpi_event_init+0x0/0x57 returned 0 after 45 msecs
but it hung hard there instead.
bisection led to this commit:
| commit 5806b81ac1
| Merge: d14c8a6... 6712e29...
| Author: Ingo Molnar <mingo@elte.hu>
| Date: Mon Jul 14 16:11:52 2008 +0200
| Merge branch 'auto-ftrace-next' into tracing/for-linus
turns out that i made this mistake in the merge:
ifdef CONFIG_FTRACE
# Do not profile debug utilities
CFLAGS_REMOVE_tsc_64.o = -pg
CFLAGS_REMOVE_tsc_32.o = -pg
those two files got unified meanwhile - so the dont-profile annotation
got lost. The proper rule is:
CFLAGS_REMOVE_tsc.o = -pg
i guess this could have been caught sooner if the CFLAGS_REMOVE* kbuild
rule aborted the build if it met a target that does not exist anymore?
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
"idle=nomwait" disables the use of the MWAIT
instruction from both C1 (C1_FFH) and deeper (C2C3_FFH)
C-states.
When MWAIT is unavailable, the BIOS and OS generally
negotiate to use the HALT instruction for C1,
and use IO accesses for deeper C-states.
This option is useful for power and performance
comparisons, and also to work around BIOS bugs
where broken MWAIT support is advertised.
http://bugzilla.kernel.org/show_bug.cgi?id=10807http://bugzilla.kernel.org/show_bug.cgi?id=10914
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
"idle=halt" limits the idle loop to using
the halt instruction. No MWAIT, no IO accesses,
no C-states deeper than C1.
If something is broken in the idle code,
"idle=halt" is a less severe workaround
than "idle=poll" which disables all power savings.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
991528d734
(ACPI: Processor native C-states using MWAIT)
started passing C2C3_FFH to _PDC to tell the BIOS
that Linux supports MWAIT for deep C-states.
However, we should first double check with the hardware
that it actually supports MWAIT before potentially exposing
a BIOS bug of an MWAIT _CST on HW that doesn't support MWAIT.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
This closes some arcane holes in single-step handling that can arise
only when user programs set TF directly (via popf or sigreturn) and
then use vDSO (syscall/sysenter) system call entry. In those entry
paths, the clear_TF_reenable case hits and we must check TIF_SINGLESTEP
to be sure our bookkeeping stays correct wrt the user's view of TF.
Signed-off-by: Roland McGrath <roland@redhat.com>
This unifies and cleans up the syscall tracing code on i386 and x86_64.
Using a single function for entry and exit tracing on 32-bit made the
do_syscall_trace() into some terrible spaghetti. The logic is clear and
simple using separate syscall_trace_enter() and syscall_trace_leave()
functions as on 64-bit.
The unification adds PTRACE_SYSEMU and PTRACE_SYSEMU_SINGLESTEP support
on x86_64, for 32-bit ptrace() callers and for 64-bit ptrace() callers
tracing either 32-bit or 64-bit tasks. It behaves just like 32-bit.
Changing syscall_trace_enter() to return the syscall number shortens
all the assembly paths, while adding the SYSEMU feature in a simple way.
Signed-off-by: Roland McGrath <roland@redhat.com>
This unifies the treatment of TIF_SINGLESTEP on i386 and x86_64.
The bit is now excluded from _TIF_WORK_MASK on i386 as it has been
on x86_64. This means the do_notify_resume() path using it is never
used, so TIF_SINGLESTEP is not cleared on returning to user mode.
Both now leave TIF_SINGLESTEP set when returning to user, so that
it's already set on an int $0x80 system call entry. This removes
the need for testing TF on the system_call path. Doing it this way
fixes the regression for PTRACE_SINGLESTEP into a sigreturn syscall,
introduced by commit 1e2e99f0e4.
The clear_TF_reenable case that sets TIF_SINGLESTEP can only happen
on a non-exception kernel entry, i.e. sysenter/syscall instruction.
That will always get to the syscall exit tracing path.
Signed-off-by: Roland McGrath <roland@redhat.com>
The enable_single_step() logic bails out early if TF is already set.
That skips some of the bookkeeping that keeps things straight.
This makes PTRACE_SINGLEBLOCK break the behavior of a user task
that was already setting TF itself in user mode.
Fix the bookkeeping to notice the old TF setting as it should.
Test case at: http://sources.redhat.com/cgi-bin/cvsweb.cgi/~checkout~/tests/ptrace-tests/tests/step-jump-cont-strict.c?cvsroot=systemtap
Signed-off-by: Roland McGrath <roland@redhat.com>
the paravirt-spinlock patches caused a boot hang with this config:
http://redhat.com/~mingo/misc/config-Wed_Jul__9_14_47_04_CEST_2008.bad
i have bisected it down to:
| commit e17b58c2e85bc2ad2afc07fb8d898017c2b75ed1
| Author: Jeremy Fitzhardinge <jeremy@goop.org>
| Date: Mon Jul 7 12:07:53 2008 -0700
|
| xen: implement Xen-specific spinlocks
i.e. applying that patch alone causes the hang. The hang happens in the
ftrace self-test:
initcall utsname_sysctl_init+0x0/0x19 returned 0 after 0 msecs
calling init_sched_switch_trace+0x0/0x4c
Testing tracer sched_switch: PASSED
initcall init_sched_switch_trace+0x0/0x4c returned 0 after 167 msecs
calling init_function_trace+0x0/0x12
Testing tracer ftrace:
[hard hang]
it should have continued like this:
Testing tracer ftrace: PASSED
initcall init_function_trace+0x0/0x12 returned 0 after 198 msecs
calling init_irqsoff_tracer+0x0/0x14
Testing tracer irqsoff: PASSED
initcall init_irqsoff_tracer+0x0/0x14 returned 0 after 3 msecs
calling init_mmio_trace+0x0/0x12
initcall init_mmio_trace+0x0/0x12 returned 0 after 0 msecs
the problem is that such lowlevel primitives as spinlocks should never
be built with -pg (which ftrace does). Marking paravirt.o as non-pg and
marking all spinlock ops as always-inline solve the hang.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Implement a version of the old spinlock algorithm, in which everyone
spins waiting for a lock byte. In order to be compatible with the
ticket-lock's use of a zero initializer, this uses the convention of
'0' for unlocked and '1' for locked.
This algorithm is much better than ticket locks in a virtual
envionment, because it doesn't interact badly with the vcpu scheduler.
If there are multiple vcpus spinning on a lock and the lock is
released, the next vcpu to be scheduled will take the lock, rather
than cycling around until the next ticketed vcpu gets it.
To use this, you must call paravirt_use_bytelocks() very early, before
any spinlocks have been taken.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Christoph Lameter <clameter@linux-foundation.org>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Virtualization <virtualization@lists.linux-foundation.org>
Cc: Xen devel <xen-devel@lists.xensource.com>
Cc: Thomas Friebel <thomas.friebel@amd.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ticket spinlocks have absolutely ghastly worst-case performance
characteristics in a virtual environment. If there is any contention
for physical CPUs (ie, there are more runnable vcpus than cpus), then
ticket locks can cause the system to end up spending 90+% of its time
spinning.
The problem is that (v)cpus waiting on a ticket spinlock will be
granted access to the lock in strict order they got their tickets. If
the hypervisor scheduler doesn't give the vcpus time in that order,
they will burn timeslices waiting for the scheduler to give the right
vcpu some time. In the worst case it could take O(n^2) vcpu scheduler
timeslices for everyone waiting on the lock to get it, not counting
new cpus trying to take the lock while the log-jam is sorted out.
These hooks allow a paravirt backend to replace the spinlock
implementation.
At the very least, this could revert the implementation back to the
old lock algorithm, which allows the next scheduled vcpu to take the
lock, and has basically fairly good performance.
It also allows the spinlocks to take advantages of the hypervisor
features to make locks more efficient (spin and block, for example).
The cost to native execution is an extra direct call when using a
spinlock function. There's no overhead if CONFIG_PARAVIRT is turned
off.
The lock structure is fixed at a single "unsigned int", initialized to
zero, but the spinlock implementation can use it as it wishes.
Thanks to Thomas Friebel's Xen Summit talk "Preventing Guests from
Spinning Around" for pointing out this problem.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Christoph Lameter <clameter@linux-foundation.org>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Virtualization <virtualization@lists.linux-foundation.org>
Cc: Xen devel <xen-devel@lists.xensource.com>
Cc: Thomas Friebel <thomas.friebel@amd.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Exceptions using paranoidentry need to have their exception frames
adjusted explicitly.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
AMD only supports "syscall" from 32-bit compat usermode.
Intel and Centaur(?) only support "sysenter" from 32-bit compat usermode.
Set the X86 feature bits accordingly, and set up the vdso in
accordance with those bits. On the offchance we run on in a 64-bit
environment which supports neither syscall nor sysenter from 32-bit
mode, then fall back to the int $0x80 vdso.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This reverts commit 033786969d1d1b5af12a32a19d3a760314d05329.
Suresh Siddha reported that this broke booting on his 2GB testbox.
Reported-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Implement the failsafe callback, so that iret and segment register
load exceptions are reported to the kernel.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add the Xen entrypoint and ELF notes to head_64.S. Adapts xen-head.S
to compile either 32-bit or 64-bit.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As a stopgap until Mike Travis's x86-64 gs-based percpu patches are
ready, provide workaround functions for x86_read/write_percpu for
Xen's use.
Specifically, this means that we can't really make use of vcpu
placement, because we can't use a single gs-based memory access to get
to vcpu fields. So disable all that for now.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This allows Xen's xen_cpu_up() to allocate a pda for the new CPU.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Update arch/x86's use of page-aligned variables. The change to
arch/x86/xen/mmu.c fixes an actual bug, but the rest are cleanups
and to set a precedent.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
process_64.c:__switch_to has some very old strange formatting, some of
it dating back to pre-git. Fix it up.
No functional changes.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Early fixmap will allocate its own L1 pagetable page for fixmap
mappings, so there's no need to preallocate one.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Call paravirt_pagetable_setup_{start,done}
These paravirt_ops functions were not being called on x86_64.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Dave Hansen reported a build error on 32bit which went unnoticed
as newer gcc versions seem to optimize unused static functions
away before compiling them.
Make vread_tsc() depend on CONFIG_X86_64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'timers/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: add PCI ID for 6300ESB force hpet
x86: add another PCI ID for ICH6 force-hpet
kernel-paramaters: document pmtmr= command line option
acpi_pm clccksource: fix printk format warning
nohz: don't stop idle tick if softirqs are pending.
pmtmr: allow command line override of ioport
nohz: reduce jiffies polling overhead
hrtimer: Remove unused variables in ktime_divns()
hrtimer: remove warning in hres_timers_resume
posix-timers: print RT watchdog message
On Mon, 2008-04-21 at 18:54 -0400, Masami Hiramatsu wrote:
> Thank you for reporting.
>
> Actually, kprobes tries to fixup thread's flags in post_kprobe_handler
> (which is called from kprobe_exceptions_notify) by
> trace_hardirqs_fixup_flags(pt_regs->flags). However, even the irq flag
> is set in pt_regs->flags, true hardirq is still off until returning
> from do_debug. Thus, lockdep assumes that hardirq is off without annotation.
>
> IMHO, one possible solution is that fixing hardirq flags right after
> notify_die in do_debug instead of in post_kprobe_handler.
My reply to BZ 10489:
> [ 2.707509] Kprobe smoke test started
> [ 2.709300] ------------[ cut here ]------------
> [ 2.709420] WARNING: at kernel/lockdep.c:2658 check_flags+0x4d/0x12c()
> [ 2.709541] Modules linked in:
> [ 2.709588] Pid: 1, comm: swapper Not tainted 2.6.25.jml.057 #1
> [ 2.709588] [<c0126acc>] warn_on_slowpath+0x41/0x51
> [ 2.709588] [<c010bafc>] ? save_stack_trace+0x1d/0x3b
> [ 2.709588] [<c0140a83>] ? save_trace+0x37/0x89
> [ 2.709588] [<c011987d>] ? kernel_map_pages+0x103/0x11c
> [ 2.709588] [<c0109803>] ? native_sched_clock+0xca/0xea
> [ 2.709588] [<c0142958>] ? mark_held_locks+0x41/0x5c
> [ 2.709588] [<c0382580>] ? kprobe_exceptions_notify+0x322/0x3af
> [ 2.709588] [<c0142aff>] ? trace_hardirqs_on+0xf1/0x119
> [ 2.709588] [<c03825b3>] ? kprobe_exceptions_notify+0x355/0x3af
> [ 2.709588] [<c0140823>] check_flags+0x4d/0x12c
> [ 2.709588] [<c0143c9d>] lock_release+0x58/0x195
> [ 2.709588] [<c038347c>] ? __atomic_notifier_call_chain+0x0/0x80
> [ 2.709588] [<c03834d6>] __atomic_notifier_call_chain+0x5a/0x80
> [ 2.709588] [<c0383508>] atomic_notifier_call_chain+0xc/0xe
> [ 2.709588] [<c013b6d4>] notify_die+0x2d/0x2f
> [ 2.709588] [<c038168a>] do_debug+0x67/0xfe
> [ 2.709588] [<c0381287>] debug_stack_correct+0x27/0x30
> [ 2.709588] [<c01564c0>] ? kprobe_target+0x1/0x34
> [ 2.709588] [<c0156572>] ? init_test_probes+0x50/0x186
> [ 2.709588] [<c04fae48>] init_kprobes+0x85/0x8c
> [ 2.709588] [<c04e947b>] kernel_init+0x13d/0x298
> [ 2.709588] [<c04e933e>] ? kernel_init+0x0/0x298
> [ 2.709588] [<c04e933e>] ? kernel_init+0x0/0x298
> [ 2.709588] [<c0105ef7>] kernel_thread_helper+0x7/0x10
> [ 2.709588] =======================
> [ 2.709588] ---[ end trace 778e504de7e3b1e3 ]---
> [ 2.709588] possible reason: unannotated irqs-off.
> [ 2.709588] irq event stamp: 370065
> [ 2.709588] hardirqs last enabled at (370065): [<c0382580>] kprobe_exceptions_notify+0x322/0x3af
> [ 2.709588] hardirqs last disabled at (370064): [<c0381bb7>] do_int3+0x1d/0x7d
> [ 2.709588] softirqs last enabled at (370050): [<c012b464>] __do_softirq+0xfa/0x100
> [ 2.709588] softirqs last disabled at (370045): [<c0107438>] do_softirq+0x74/0xd9
> [ 2.714751] Kprobe smoke test passed successfully
how I love this stuff...
Ok, do_debug() is a trap, this can happen at any time regardless of the
machine's IRQ state. So the first thing we do is fix up the IRQ state.
Then we call this die notifier stuff; and return with messed up IRQ
state... YAY.
So, kprobes fudges it..
notify_die(DIE_DEBUG)
kprobe_exceptions_notify()
post_kprobe_handler()
modify regs->flags
trace_hardirqs_fixup_flags(regs->flags); <--- must be it
So what's the use of modifying flags if they're not meant to take effect
at some point.
/me tries to reproduce issue; enable kprobes test thingy && boot
OK, that reproduces..
So the below makes it work - but I'm not getting this code; at the time
I wrote that stuff I CC'ed each and every kprobe maintainer listed in
the usual places but got no reposonse - can some please explain this
stuff to me?
Are the saved flags only for the TF bit or are they made in full effect
later (and if so, where) ?
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-2.6.27' of git://git.infradead.org/users/dwmw2/firmware-2.6: (64 commits)
firmware: convert sb16_csp driver to use firmware loader exclusively
dsp56k: use request_firmware
edgeport-ti: use request_firmware()
edgeport: use request_firmware()
vicam: use request_firmware()
dabusb: use request_firmware()
cpia2: use request_firmware()
ip2: use request_firmware()
firmware: convert Ambassador ATM driver to request_firmware()
whiteheat: use request_firmware()
ti_usb_3410_5052: use request_firmware()
emi62: use request_firmware()
emi26: use request_firmware()
keyspan_pda: use request_firmware()
keyspan: use request_firmware()
ttusb-budget: use request_firmware()
kaweth: use request_firmware()
smctr: use request_firmware()
firmware: convert ymfpci driver to use firmware loader exclusively
firmware: convert maestro3 driver to use firmware loader exclusively
...
Fix up trivial conflicts with BKL removal in drivers/char/dsp56k.c and
drivers/char/ip2/ip2main.c manually.
* 'core/printk' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, generic: mark early_printk as asmlinkage
printk: export console_drivers
printk: remember the message level for multi-line output
printk: refactor processing of line severity tokens
printk: don't prefer unsuited consoles on registration
printk: clean up recursion check related static variables
namespacecheck: more kernel/printk.c fixes
namespacecheck: fix kernel printk.c
* 'tracing/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (228 commits)
ftrace: build fix for ftraced_suspend
ftrace: separate out the function enabled variable
ftrace: add ftrace_kill_atomic
ftrace: use current CPU for function startup
ftrace: start wakeup tracing after setting function tracer
ftrace: check proper config for preempt type
ftrace: trace schedule
ftrace: define function trace nop
ftrace: move sched_switch enable after markers
ftrace: prevent ftrace modifications while being kprobe'd, v2
fix "ftrace: store mcount address in rec->ip"
mmiotrace broken in linux-next (8-bit writes only)
ftrace: avoid modifying kprobe'd records
ftrace: freeze kprobe'd records
kprobes: enable clean usage of get_kprobe
ftrace: store mcount address in rec->ip
ftrace: build fix with gcc 4.3
namespacecheck: fixes
ftrace: fix "notrace" filtering priority
ftrace: fix printout
...
Explain that we set up the descriptors for Big Real Mode, and why we
do so. In particular, one system that is known to fail without it is
the Lenovo X61.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The explanation for recent video BIOS suspend quirk failures is that
the VESA BIOS expects to be entered in Big Real Mode (*.limit = 0xffffffff)
instead of ordinary Real Mode (*.limit = 0xffff).
This patch changes the segment descriptors to Big Real Mode instead.
The segment descriptor registers (what Intel calls "segment cache") is
always active. The only thing that changes based on CR0.PE is how it is
*loaded* and the interpretation of the CS flags.
The segment descriptor registers contain of the following sub-registers:
selector (the "visible" part), base, limit and flags. In protected mode
or long mode, they are loaded from descriptors (or fs.base or gs.base can
be manipulated directly in long mode.) In real mode, the only thing
changed by a segment register load is the selector and the base, where the
base <- selector << 4. In particular, *the limit and the flags are not
changed*.
As far as the handling of the CS flags: a code segment cannot be writable
in protected mode, whereas it is "just another segment" in real mode, so
there is some kind of quirk that kicks in for this when CR0.PE <- 0. I'm
not sure if this is accomplished by actually changing the cs.flags register
or just changing the interpretation; it might be something that is
CPU-specific. In particular, the Transmeta CPUs had an explicit "CS is
writable if you're in real mode" override, so even if you had loaded CS
with an execute-only segment it'd be writable (but not readable!) on return
to real mode. I'm not at all sure if that is how other CPUs behave.
Signed-off-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when try to make hpet_enable use io_remap instead fixmap got
ioremap: invalid physical address fed00000
------------[ cut here ]------------
WARNING: at arch/x86/mm/ioremap.c:161 __ioremap_caller+0x8c/0x2f3()
Modules linked in:
Pid: 0, comm: swapper Not tainted 2.6.26-rc9-tip-01873-ga9827e7-dirty #358
Call Trace:
[<ffffffff8026615e>] warn_on_slowpath+0x6c/0xa7
[<ffffffff802e2313>] ? __slab_alloc+0x20a/0x3fb
[<ffffffff802d85c5>] ? mpol_new+0x88/0x17d
[<ffffffff8022a4f4>] ? mcount_call+0x5/0x31
[<ffffffff8022a4f4>] ? mcount_call+0x5/0x31
[<ffffffff8024b0d2>] __ioremap_caller+0x8c/0x2f3
[<ffffffff80e86dbd>] ? hpet_enable+0x39/0x241
[<ffffffff8022a4f4>] ? mcount_call+0x5/0x31
[<ffffffff8024b466>] ioremap_nocache+0x2a/0x40
[<ffffffff80e86dbd>] hpet_enable+0x39/0x241
[<ffffffff80e7a1f6>] hpet_time_init+0x21/0x4e
[<ffffffff80e730e9>] start_kernel+0x302/0x395
[<ffffffff80e722aa>] x86_64_start_reservations+0xb9/0xd4
[<ffffffff80e722fe>] ? x86_64_init_pda+0x39/0x4f
[<ffffffff80e72400>] x86_64_start_kernel+0xec/0x107
---[ end trace a7919e7f17c0a725 ]---
it seems for amd system that is set later...
try to move setting early in early_identify_cpu.
and remove same code for intel and centaur.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
only add direct mapping for aperture
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix for pv - clean up the namespace there too.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Strengthen the return type for the _node_to_cpumask_ptr to be
a const pointer. This adds compiler checking to insure that
node_to_cpumask_map[] is not changed inadvertently.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: "akpm@linux-foundation.org" <akpm@linux-foundation.org>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that IRQ2 is never made available to the I/O APIC, there is no need
to special-case it and mask as a workaround for broken systems. Actually,
because of the former, mask_IO_APIC_irq(2) is a no-op already.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
generalize the x2apic code some more.
let read_apic_id become a macro (later on a function/inline)
GET_APIC_ID(apic_read(APIC_ID))
+#define read_apic_id() (GET_APIC_ID(apic_read(APIC_ID)))
instead of this weird construct:
-#define read_apic_id (genapic->read_apic_id)
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
got this on a test-system:
calling numaq_tsc_disable+0x0/0x39
NUMAQ: disabling TSC
initcall numaq_tsc_disable+0x0/0x39 returned 0 after 0 msecs
that's because we should not be using arch_initcall to call numaq_tsc_disable.
need to call it in setup_arch before time_init()/tsc_init()
and call it in init_intel() to make the cpu feature bits right.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
end_user_pfn used to modify the meaning of the e820 maps.
Now that all e820 operations are cleaned up, unified, tightened up,
the e820 map always get updated to reality, we don't need to keep
this secondary mechanism anymore.
If you hit this commit in bisection it means something slipped through.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
tighten the boundary checks around max_low_pfn_mapped - dont overmap
nor undermap into holes.
also print out tseg for AMD cpus, for diagnostic purposes.
(this is an SMM area, and we split up any big mappings around that area)
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
also remove GET_APIC_ID when read_apic_id is used.
need to apply after
[PATCH] x86: mach_apicdef.h need to include before smp.h
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andrew says:
> There's no point in declaring it inline if it's always called indirectly.
And point taken!
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
x2apic support. Interrupt-remapping must be enabled before enabling x2apic,
this is needed to ensure that IO interrupts continue to work properly after the
cpu mode is changed to x2apic(which uses 32bit extended physical/cluster
apic id).
On systems where apicid's are > 255, BIOS can handover the control to OS in
x2apic mode. Or if the OS handover was in legacy xapic mode, check
if it is capable of x2apic mode. And if we succeed in enabling
Interrupt-remapping, then we can enable x2apic mode in the CPU.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
MSI and MSI-X support for interrupt remapping infrastructure.
MSI address register will be programmed with interrupt-remapping table
entry(IRTE) index and the IRTE will contain information about the vector,
cpu destination, etc.
For MSI-X, all the IRTE's will be consecutively allocated in the table,
and the address registers will contain the starting index to the block
and the data register will contain the subindex with in that block.
This also introduces a new irq_chip for cleaner irq migration (in the process
context as opposed to the current irq migration in the context of an interrupt.
interrupt-remapping infrastructure will help us achieve this).
As MSI is edge triggered, irq migration is a simple atomic update(of vector
and cpu destination) of IRTE and flushing the hardware cache.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
IO-APIC support in the presence of interrupt-remapping infrastructure.
IO-APIC RTE will be programmed with interrupt-remapping table entry(IRTE)
index and the IRTE will contain information about the vector, cpu destination,
trigger mode etc, which traditionally was present in the IO-APIC RTE.
Introduce a new irq_chip for cleaner irq migration (in the process
context as opposed to the current irq migration in the context of an interrupt.
interrupt-remapping infrastructure will help us achieve this cleanly).
For edge triggered, irq migration is a simple atomic update(of vector
and cpu destination) of IRTE and flush the hardware cache.
For level triggered, we need to modify the io-apic RTE aswell with the update
vector information, along with modifying IRTE with vector and cpu destination.
So irq migration for level triggered is little bit more complex compared to
edge triggered migration. But the good news is, we use the same algorithm
for level triggered migration as we have today, only difference being,
we now initiate the irq migration from process context instead of the
interrupt context.
In future, when we do a directed EOI (combined with cpu EOI broadcast
suppression) to the IO-APIC, level triggered irq migration will also be
as simple as edge triggered migration and we can do the irq migration
with a simple atomic update to IO-APIC RTE.
TBD: some tests/changes needed in the presence of fixup_irqs() for
level triggered irq migration.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce basic apic operations which handle the apic programming. This
will be used later to introduce another specific operations for x2apic.
For the perfomance critial accesses like IPI's, EOI etc, we use the
native operations as they are already referenced by different
indirections like genapic, irq_chip etc.
64bit Paravirt ops can also define their apic operations accordingly.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On three of the several paths in entry_64.S that call
do_notify_resume() on the way back to user mode, we fail to properly
check again for newly-arrived work that requires another call to
do_notify_resume() before going to user mode. These paths set the
mask to check only _TIF_NEED_RESCHED, but this is wrong. The other
paths that lead to do_notify_resume() do this correctly already, and
entry_32.S does it correctly in all cases.
All paths back to user mode have to check all the _TIF_WORK_MASK
flags at the last possible stage, with interrupts disabled.
Otherwise, we miss any flags (TIF_SIGPENDING for example) that were
set any time after we entered do_notify_resume(). More work flags
can be set (or left set) synchronously inside do_notify_resume(), as
TIF_SIGPENDING can be, or asynchronously by interrupts or other CPUs
(which then send an asynchronous interrupt).
There are many different scenarios that could hit this bug, most of
them races. The simplest one to demonstrate does not require any
race: when one signal has done handler setup at the check before
returning from a syscall, and there is another signal pending that
should be handled. The second signal's handler should interrupt the
first signal handler before it actually starts (so the interrupted PC
is still at the handler's entry point). Instead, it runs away until
the next kernel entry (next syscall, tick, etc).
This test behaves correctly on 32-bit kernels, and fails on 64-bit
(either 32-bit or 64-bit test binary). With this fix, it works.
#define _GNU_SOURCE
#include <stdio.h>
#include <signal.h>
#include <string.h>
#include <sys/ucontext.h>
#ifndef REG_RIP
#define REG_RIP REG_EIP
#endif
static sig_atomic_t hit1, hit2;
static void
handler (int sig, siginfo_t *info, void *ctx)
{
ucontext_t *uc = ctx;
if ((void *) uc->uc_mcontext.gregs[REG_RIP] == &handler)
{
if (sig == SIGUSR1)
hit1 = 1;
else
hit2 = 1;
}
printf ("%s at %#lx\n", strsignal (sig),
uc->uc_mcontext.gregs[REG_RIP]);
}
int
main (void)
{
struct sigaction sa;
sigset_t set;
sigemptyset (&sa.sa_mask);
sa.sa_flags = SA_SIGINFO;
sa.sa_sigaction = &handler;
if (sigaction (SIGUSR1, &sa, NULL)
|| sigaction (SIGUSR2, &sa, NULL))
return 2;
sigemptyset (&set);
sigaddset (&set, SIGUSR1);
sigaddset (&set, SIGUSR2);
if (sigprocmask (SIG_BLOCK, &set, NULL))
return 3;
printf ("main at %p, handler at %p\n", &main, &handler);
raise (SIGUSR1);
raise (SIGUSR2);
if (sigprocmask (SIG_UNBLOCK, &set, NULL))
return 4;
if (hit1 + hit2 == 1)
{
puts ("PASS");
return 0;
}
puts ("FAIL");
return 1;
}
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We have two conflicting DMA-based quirks in there for the same set of
boxes (HP nx6325 and nx6125) and one of them actually breaks my box.
So remove the extra code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: =?iso-8859-1?q?T=F6r=F6k_Edwin?= <edwintorok@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In the course of the recent unification of the NMI watchdog an assignment
to timer_ack to switch off unnecesary POLL commands to the 8259A in the
case of a watchdog failure has been accidentally removed. The statement
used to be limited to the 32-bit variation as since the rewrite of the
timer code it has been relevant for the 82489DX only. This change brings
it back.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is no such entity as ISA IRQ2. The ACPI spec does not make it
explicitly clear, but does not preclude it either -- all it says is ISA
legacy interrupts are identity mapped by default (subject to overrides),
but it does not state whether IRQ2 exists or not. As a result if there is
no IRQ0 override, then IRQ2 is normally initialised as an ISA interrupt,
which implies an edge-triggered line, which is unmasked by default as this
is what we do for edge-triggered I/O APIC interrupts so as not to miss an
edge.
To the best of my knowledge it is useless, as IRQ2 has not been in use
since the PC/AT as back then it was taken by the 8259A cascade interrupt
to the slave, with the line position in the slot rerouted to newly-created
IRQ9. No device could thus make use of this line with the pair of 8259A
chips. Now in theory INTIN2 of the I/O APIC may be usable, but the
interrupt of the device wired to it would not be available in the PIC mode
at all, so I seriously doubt if anybody decided to reuse it for a regular
device.
However there are two common uses of INTIN2. One is for IRQ0, with an
ACPI interrupt override (or its equivalent in the MP table). But in this
case IRQ2 is gone entirely with INTIN0 left vacant. The other one is for
an 8959A ExtINTA cascade. In this case IRQ0 goes to INTIN0 and if ACPI is
used INTIN2 is assumed to be IRQ2 (there is no override and ACPI has no
way to report ExtINTA interrupts). This is where a problem happens.
The problem is INTIN2 is configured as a native APIC interrupt, with a
vector assigned and the mask cleared. And the line may indeed get active
and inject interrupts if the master 8959A has its timer interrupt enabled
(it might happen for other interrupts too, but they are normally masked in
the process of rerouting them to the I/O APIC). There are two cases where
it will happen:
* When the I/O APIC NMI watchdog is enabled. This is actually a misnomer
as the watchdog pulses are delivered through the 8259A to the LINT0
inputs of all the local APICs in the system. The implication is the
output of the master 8259A goes high and low repeatedly, signalling
interrupts to INTIN2 which is enabled too!
[The origin of the name is I think for a brief period during the
development we had a capability in our code to configure the watchdog to
use an I/O APIC input; that would be INTIN2 in this scenario.]
* When the native route of IRQ0 via INTIN0 fails for whatever reason -- as
it happens with the system considered here. In this scenario the timer
pulse is delivered through the 8259A to LINT0 input of the local APIC of
the bootstrap processor, quite similarly to how is done for the watchdog
described above. The result is, again, INTIN2 receives these pulses
too. Rafael's system used to escape this scenario, because an incorrect
IRQ0 override would occupy INTIN2 and prevent it from being unmasked.
My conclusion is IRQ2 should be excluded from configuration in all the
cases and the current exception for ACPI systems should be lifted. The
reason being the exception not only being useless, but harmful as well.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Unlike the 32-bit one, the 64-bit variation of the LVT0 setup code for
the "8259A Virtual Wire" through the local APIC timer configuration does
not fully configure the relevant irq_chip structure. Instead it relies on
the preceding I/O APIC code to have set it up, which does not happen if
the I/O APIC variants have not been tried.
The patch includes corresponding changes to the 32-bit variation too
which make them both the same, barring a small syntactic difference
involving sequence of functions in the source. That should work as an aid
with the upcoming merge.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
IRQ0 is edge-triggered, but the "8259A Virtual Wire" through the local
APIC configuration in the 32-bit version uses the "fasteoi" handler
suitable for level-triggered APIC interrupt. Rewrite code so that the
"edge" handler is used. The 64-bit version uses different code and is
unaffected.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The RING0_INT_FRAME macro defines a CFI_STARTPROC.
So we should really be using CFI_ENDPROC after it.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch removes the memset from the data structure initialization code and
allocate the structures with the __GFP_ZERO flag.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: iommu@lists.linux-foundation.org
Cc: bhavna.sarathy@amd.com
Cc: robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch removes an unneeded initialization from the alloc_command_buffer
function and replaces a memset with __GFP_ZERO.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: iommu@lists.linux-foundation.org
Cc: bhavna.sarathy@amd.com
Cc: robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add pseudo-feature bits to describe whether the CPU supports sysenter
and/or syscall from ia32-compat userspace. This removes a hardcoded
test in vdso32-setup.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yinghai Lu reported crashes on 64-bit x86:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
IP: [<ffffffff80253b17>] hrtick_start_fair+0x89/0x173
[...]
And with a long session of debugging and a lot of difficulty, tracked it down
to this commit:
--------------->
8fbbc4b45c is first bad commit
commit 8fbbc4b45c
Author: Alok Kataria <akataria@vmware.com>
Date: Tue Jul 1 11:43:34 2008 -0700
x86: merge tsc_init and clocksource code
<--------------
The problem is that the TSC unification missed these Makefile rules
in arch/x86/kernel/Makefile:
# Do not profile debug and lowlevel utilities
CFLAGS_REMOVE_tsc_64.o = -pg
CFLAGS_REMOVE_tsc_32.o = -pg
...
CFLAGS_tsc_64.o := $(nostackp)
...
which rules make sure that various instrumentation and debugging
facilities are disabled for code that might end up in a VDSO - such as
the TSC code.
Reported-and-bisected-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As other IOMMUs do, this puts dummy pci_swiotlb_init() in swiotlb.h
and remove ifdef CONFIG_SWIOTLB in pci-dma.c.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
asm-x86/calgary.h has dummy calgary_iommu_init() and detect_calgary()
in !CONFIG_CALGARY_IOMMU case. So we don't need ifdef
CONFIG_CALGARY_IOMMU in pci-dma.c.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Alexis Bruemmer <alexisb@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Our way to handle gart_* functions for CONFIG_GART_IOMMU and
!CONFIG_GART_IOMMU cases is inconsistent.
We have some dummy gart_* functions in !CONFIG_GART_IOMMU case and
also use ifdef CONFIG_GART_IOMMU tricks in pci-dma.c to call some
gart_* functions in only CONFIG_GART_IOMMU case.
This patch removes ifdef CONFIG_GART_IOMMU in pci-dma.c and always use
dummy gart_* functions in iommu.h.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
gart.h has only GART-specific stuff. Only GART code needs it. Other
IOMMU stuff should include iommu.h instead of gart.h.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when more than 4g memory is installed, don't map the big hole below 4g.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
also let mem= to print out modified e820 map too
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Integration generated a duplicate call to use_tsc_delay.
Particularly, the one that is done before we check for general
tsc usability seems wrong.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/visws_quirks.c: In function ‘visws_early_detect’:
arch/x86/kernel/visws_quirks.c:293: error: ‘no_broadcast’ undeclared (first use in this function)
arch/x86/kernel/visws_quirks.c:293: error: (Each undeclared identifier is reported only once
arch/x86/kernel/visws_quirks.c:293: error: for each function it appears in.)
make[1]: *** [arch/x86/kernel/visws_quirks.o] Error 1
make: *** [arch/x86/kernel/visws_quirks.o] Error 2
Signed-off-by: Ingo Molnar <mingo@elte.hu>
this is the big move: flip over VISWS to generic arch support.
From this commit on CONFIG_X86_VISWS is just another (default-disabled)
option that turns on certain quirks - no other complications.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
copy arch/x86/mach-visws/setup_visws.c, apic_visws.c and traps_visws.c
files to arch/x86/kernel/, in preparation of the switchover to a
non-subarch setup for VISWS.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
first step: make the VISWS subarch boot on a regular PC.
We take various shortcuts for that. We copy the generic arch setup file over
into the VISWS setup file.
This is the only step that is not expected to boot on a real VISWS.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add early quirks support.
In preparation of enabling the generic architecture to boot on a VISWS.
This will allow us to remove the VISWS subarch and all its complications.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When an interrupt is rerouted to a different I/O APIC pin the relevant
entry of the irq_2_pin list should get updated accordingly so that
operations are performed on the correct redirection entry.
This is already done by the 32-bit variation of the code and here is a
complementing 64-bit implementation. Should make someone's decision less
tough when merging the two. ;)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 90221a61a71b7ad659d8741cf1e404506b174982.
This too was just temporary diagnostics - not needed now that we've
got the final fix via:
| commit e2079c4386
| Author: Rafael J. Wysocki <rjw@sisk.pl>
| Date: Tue Jul 8 16:12:26 2008 +0200
|
| x86: fix C1E && nx6325 stability problem
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit a74a1cc3df0be89658bc735c8aed80c8392e2c15.
This was just temporary diagnostics commit - not needed now that we've
got the final fix.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
even on 64bit systems with less than 4G RAM, we can now use fixmap
to handle acpi SIT near end of ram.
change e820_end to e820_end_of_ram again?
or e820_ram_pfn?
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
and let 64-bit to fall back to use fixmap too.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
to avoid warning from find_low_pfn_range for high pages size etc
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/acpi/boot.c: In function ‘dmi_ignore_irq0_timer_override’:
arch/x86/kernel/acpi/boot.c:1443: error: implicit declaration of function ‘force_mask_ioapic_irq_2’
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The problems are that, with the ACPI vs timer overring issue _fixed_,
after using the box for some time (between several seconds and 1 hour, at
random) processes get very high CPU loads (once I've got X using 107% of
the CPU, for example) and the system becomes unresponsive, as though there
were interrupts lost or something similar.
Andreas Herrman reproduced similar problems:
> Ok, now I've reproduced the stability problem.
> - Using tip/master,
> - reverting e38502eb8aa82314d5ab0eba45f50e6790dadd88 and
> - applying your patch from this posting
> http://marc.info/?l=linux-kernel&m=121539354224562&w=4
>
> Starting X, firefox, gimp, tuxpaint and doing some drawing in tuxpaint
> results in a slow system. Drawing is almost not possible anymore --
> Selections of new colors, cursors etc. is performed with huge delay
> if it's performed at all.
>
> BTW, the code sets up timer IRQ as Virtual Wire IRQ:
>
> Jul 8 14:57:58 kodscha IO-APIC (apicid-pin) 2-22, 2-23 not connected.
> Jul 8 14:57:58 kodscha ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
> Jul 8 14:57:58 kodscha ...trying to set up timer as Virtual Wire IRQ... works.
>
> and both INT0 and INT2 of IOAPIC are masked:
>
> Jul 8 14:57:58 kodscha NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
> Jul 8 14:57:58 kodscha 00 000 1 0 0 0 0 0 0 00
> Jul 8 14:57:58 kodscha 01 003 0 0 0 0 0 1 1 31
> Jul 8 14:57:58 kodscha 02 003 1 0 0 0 0 0 0 30
>
> I've also seen strange CPU utilization -- with syslog-ng:
>
> top - 15:33:06 up 35 min, 4 users, load average: 1.70, 0.68, 0.37
> Tasks: 64 total, 4 running, 60 sleeping, 0 stopped, 0 zombie
> Cpu0 : 0.0%us,100.0%sy, 0.0%ni, 0.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
> Cpu1 : 6.4%us, 87.2%sy, 0.0%ni, 5.8%id, 0.0%wa, 0.6%hi, 0.0%si, 0.0%st
> Mem: 895384k total, 283568k used, 611816k free, 35492k buffers
> Swap: 1959920k total, 0k used, 1959920k free, 163044k cached
>
> PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
> 4632 root 20 0 17216 800 580 S 104 0.1 0:34.22 syslog-ng
> 28505 root 20 0 205m 11m 4024 S 6 1.3 0:21.16 X
> 28518 root 20 0 56292 5652 4492 S 1 0.6 0:01.80 fluxbox
> 1 root 20 0 3724 608 508 S 0 0.1 0:00.36 init
>
> So far I have no clue why C1E-idle in conjunction with virtual wire
> mode causes this strange behaviour.
>
> ... and I start to think about the root cause of all this.
>
> I've performed similar tests under X with the IRQ0/INT0 configuration and
> I did not see above symptoms.
So lets fall back to the IRQ0/INT0 configuration on this box.
This basically restores the dont-use-the-lapic-timer exception mechanism
that was unconditional on this box prior commit 8750bf5 ("x86: add C1E
aware idle function").
Signed-off-by: Ingo Molnar <mingo@elte.hu>
One of the last IOMMU updates covered a bug in the AMD IOMMU code. The early
detection code does not succeed if the GART is already detected. This patch
fixes this.
Cc: Robert Richter <robert.richter@amd.com>
Cc: Bhavna Sarathy <Bhavna.Sarathy@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: iommu@lists.linux-foundation.org
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Bhavna Sarathy <Bhavna.Sarathy@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
