82598 and 82599 do not support SFP 1G modules. Instead of allowing the
driver to load, but never get link, rejecting the module and displaying
a useful message is more preferrable. The framework for displaying the
failure message already exists, now we just need to detect and reject the
SFP modules.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code writes the PME enabled bit in PCI config space which is
wrong. This was needed for pre-release hardware, and was not removed from
the driver. Also, we need to clear the WUS (wake up status) after we
resume. Otherwise we can't wake for the same event again since it's still
asserted in the hardware. Plus, the multicast lists were being written
improperly, causing multicast WoL to fail.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Andrew Lutomirski <amluto@gmail.com>
All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice
This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.
This apparently confused *some* versions of networkmanager.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: Andrew Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The thresholds for the DCB priority flow control are incorrect for 82599.
This fixes the thresholds to be correct.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The traffic classes in hardware are not symmetrical for Rx and Tx. Rx
is every 16 descriptor queues, Tx is not. It runs 32-32-16-16-8-8-8 when
running with 8 traffic classes, and runs 64-32-16 when running with 4
traffic classes. This patch fixes the mapping.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC warns:
drivers/net/ixgbe/ixgbe_main.c: In function 'ixgbe_sfp_config_module_task':
drivers/net/ixgbe/ixgbe_main.c:3920: warning: suggest parantheses around
operand of '!' or change '&' to '&&' or '!' to '~'
Which I think is right. Bracket to remove ambiguity.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent ixgbe from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate ixgbe_shutdown() from ixgbe_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the update of real_num_tx_queues from
ixgbe_acquire_msix_vectors() to ixgbe_set_num_queues(), to ensure it
be always in sync with num_tx_queues.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't do the num_tx_queues based masking on calculating tx queue
index.
1) num_tx_queues is not always power-of-2, because it also depends on
the online cpu numbers. So the masking could be a performance bug
on a 6 cpu system.
2) queue_mapping will be limited by real_num_tx_queues=num_tx_queues
in the generic netdev function set_cur_queue_map(). So the bound
limiting here is not necessary.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC warns:
drivers/net/ixgbe/ixgbe_main.c: In function 'ixgbe_sfp_config_module_task':
drivers/net/ixgbe/ixgbe_main.c:3920: warning: suggest parantheses around
operand of '!' or change '&' to '&&' or '!' to '~'
Which I think is right. Bracket to remove ambiguity.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all physical connection types are being correctly identified. This
fixes that issue, and cleans up the logic to make it more maintainable.
Also clean up the code for device capabilities from the EEPROM to support
multiple SKUs of the same hardware.
Bump the version to reflect all the updates since the 82599 merge.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The orig_autoc variable tracks the original setting of the autonegotiate
state prior to trying a new speed. The usage is inconsistent and not very
maintainable. This patch updates the usage to make it more consistent.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does two things:
1) On 82599, the PHY is emedded in the MAC. On 82598, the SFP+ NIC has an external PHY. The reset in the SFP+ setup patch for 82598 is unnecessary on 82599, and adds extra dead time to device initialization. This removes that PHY reset for 82599 only.
2) On 82599, the SFP+ modules are multispeed fiber modules (10G/1G). We need to make sure to identify them properly for the remaining init sections to properly set them up.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PHY operations are determined, the PHY must be identified. This
identification causes bus access, and should be contained within its own
routines. This also helps the 82599 PHY init paths for both SFP+ and
KX/KX4 devices to be easier to maintain.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When flow control is disabled, an invalid low/high watermark configuration
should not matter.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 supports 64 IVAR registers this patch adds a define to
allow us to access them.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These defines allow for definition of target pool for packets that
pass L2 filtering but didn't pass any of the pool filters. They are
needed to reset the default pool.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IXGBE_MTQC_64VF was wrong and 32VF not defined at all. This patch
corrects that.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The discard pause frames bit was not enabled, so flow control frames could
be passed up to the host. Enabled DPF to keep the frames off the stack.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All NICs were reporting WOL support when only the KX4 NIC is capable of
supporting WOL. This patch adds a function to check for and exclude all
non-WOL capable nics from enabling WOL in ethtool.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LED blink code is common for 82599 as well. It should be moved to
ixgbe_common.c so both devices can use it, and not have it duplicated.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While setting up the ring parameters using ethtool the driver can
panic or leak memory as ixgbe_open tries to setup tx & rx resources.
The updated logic will use ixgbe_down/up after successful allocation of
tx & rx resources
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
We were basicly ignoring ethtool users request for FC autoneg
and replying to queries with a "best guess". This patch
enables the driver to store if we want to enable/disable
autoneg FC and do the correct behavior.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When network interface is made active we were not handling the error
scenarios properly to clean up rx & tx resources which might result in
a driver panic.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves an issue with map single being used to map a buffer and
then unmap page being used to unmap it. In addition it handles any error
conditions that may be detected using skb_dma_map.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MSI-X allocation broke after the 82599 merge on systems with more than 8
CPU cores. 82598 drops back into MSI mode, which isn't sufficient to run
full, efficient 10G line rate.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the past flow control wasn't enabled by default under the
incorrect assumption that this opened up us to a denial of
service attack. However since any switch that forwarded flow
control would be extremely msiconfigured and/or buggy, this
concern no longer out weighs the preformance gains from
having FC enabled.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The priority flow control settings from the netlink layer aren't taking
effect in the base driver. The boolean pfc_mode_enable in the dcb_config
struct isn't being set, so the hardware configuration code is never
reached.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool tries to get advertised speed from phy.autoneg_advertised.
However for copper media this wasn't happening until later do to
an other fix which moved mac.ops.setup_link_speed placement in
ixgbe_link_config(). This patch will display the default advertised
speeds if it can't yet get this information from phy.autoneg_advertised.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ixgbe driver had issues when DEBUG was defined because the hw_dbg macro
was incomplete. This patch completes the code based off of the code that
already existed in the igb module.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing DCB parameters, ixgbe needs to have the MAC reset. The way
the flow control code is setup today, PFC will be disabled on a reset.
This patch adds a new flow control type for PFC, and then has the netlink
layer take care of toggling which type of flow control to enable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert ixgbe to use net_device_ops properly.
Rather than changing the select_queue function pointer
just check the flag.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The watchdog will schedule an interrupt to help make sure queues are
cleaned in the case when an interrupt is missed, most likely due to very
high load. On 82599, there are extra interrupt registers to account for
the larger number of MSI-X vectors (64 total for 82599 vs. 18 total for
82598). These must be taken into account when performing this operation in
the watchdog.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool isn't reporting the support level of WoL for 82599 KX4 devices.
While the device does support WoL, ethtool was never updated to properly
report the level of support, nor will it allow ethtool to modify the type
of packets to listen for.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82598's PCI bus reporting on driver load was broken after 82599 merged.
This results in incorrect reporting, and an erroneous warning message
that the 82598 is in a PCIe slot that isn't fast enough to run 10GbE.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup a bit of whitespace, add some function header comments, and fix a
few comments around the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx DMA unit should be disabled when bringing the device down. Also,
the KX4 device with 82599 supports WoL, so we should clear the Wake Up
Status (WUS) after a PCIe slot reset.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are possible times that a driver may fail to completely initialize,
due to a buggy platform or a buggy kernel. In those cases, we'd rather
fail gracefully instead of a panic. Add a few safety checks to some
critical paths to try and prevent a panic in these corner-case situations.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleans up the following pieces of the Rx initialization path:
- Enable the ECC memory fault interrupt in OTHER causes.
- Fix an 82598 initialization of RDRXCTL when depending on RSS and VMDq to
be enabled. We don't need these features enabled to safely set the MVMEN
bit to allow multiple SRRCTL register mappings into the RXDCTL registers.
- Fix the RSS initialization path to not stomp on DCB accidentally. When
configuring the MRQC (multiple Rx queue contol) register, we want to make
sure we only OR in features as necessary, instead of full assignment.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx accounting when cleaning during NAPI was not completely properly.
We should use the work_limit to determine when to finish cleaning, and
use the same to return the cleaned status. The impact of running like this
causes the NAPI clean for this Tx to get stuck in a scheduling loop, and
can result in Tx not getting cleaned, ending with a Tx hang and device
reset.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionally if the driver was loaded in a system that
didn't support MSI-X or MSI and was on a shared interrupt,
the driver would then panic in NAPI on the first shared
interrupt because we hadn't called napi_add yet.
Solution: call napi_add before calling request_irq
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt models using EITR have changed in 82599. The way the register
is laid out, the change is transparent to some of the existing code.
However, some of it isn't. This patch fixes all the cases where EITR
handling is different than 82598.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 mistakenly enabled drop on Rx queues in the packet buffer. The
default mode should be store-and-forward from the FIFO.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_no_dma_resources counter reported by ethtool -S ethX is not
counting correctly. In 82599, the queue mappings for the counters need
to be mapped properly, and accounted for properly.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A purely cosmetic change. Report which physical layer is present, instead
of PHY unknown. 82599 added new PHY types for the SFP+ devices, and this
was missed getting updated.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple unicast address support appears to have been broken with the
change to support net_device_ops. This a regression from 2.6.28 to 2.6.29.
I'm not 100% on whether ndo_set_multicast_list can be NULL after this
or not. If ndo_set_rx_mode is set everything _should_ be using it.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'pap' is never used in ixgbe_dcb_hw_config_82599()
and 'eec' in ixgbe_acquire_eeptom() is only used when
status == 0 but GCC has some trouble seeing that.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the hardware-specific code in place, add all supported device id's,
along with base driver changes to enable 82599 devices. The devices
being enabled are:
8086:10f7: 82599EB 10 Gigabit KX4 Network Connection
8086:10fb: 82599EB 10 Gigabit Network Connection
The device 8086:10fb is a fully-pluggable SFP+ NIC.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the DCB (Data Center Bridging) support for 82599 hardware.
This is similar to how the 82598 DCB code works.
This patch also removes the BCN (Backwards Congestion Notification) netlink
configuration code from the driver. BCN was a pre-standard congestion
notification framework, and was not what the IEEE body decided upon for
standard congestion management. QCN (802.1Qau), Quantized Congestion
Notification is the accepted standard, which is not supported by 82599,
hence we remove the support altogether.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the hardware initialization code specific to 82599. This
is similar to the 82598 hardware initialization code. It also includes all
changes to the existing hardware init code to support 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it was pointed out on the list that ixgbe was failing when using 64kB pages
and large 16kB MTU.
since with a 64kB PAGE_SIZE MAX_SKB_FRAGS = 3, the way the driver was
configuring page usage was assuming 2kB is half a page, and was only
ever dmaing that much data to a half page.
(16kB - header size) / 2048 = 7 or 8 pages, which would far exceed 3
adjust the driver to account for these large pages, the hardware can
support DMA to up to 16kB for each descriptor.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Shannon Nelson <shannon.nelson@intel.com>
The ring_feature member of ixgbe_adapter is statically allocated based on
the supported features of the device. When a new feature is added, we need
to manually update the static allocation. This patch makes the feature
list an enum, eliminating the need for multiple updates to the code when
adding a new feature.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The failure happens when an interrupt occurs and the driver is reading
EICR. This read will cause a clear-by-read which leads to two TLP
being inserted in the PCIe retry buffer leading to an overflow of the
buffer and corruption of TLPs.
The solution is different depending where the reading of EICR takes place.
For ixgbe_msix_lsc() since we are in MSIX mode and know OCD is enabled a
clear-by-write is done instead of the normal clear-by-read.
For ixgbe_intr() 0xffffffff is written to EIMC before the read, masking the
interrupts.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Make symbol static.
Fix this sparse warning:
drivers/net/ixgbe/ixgbe_82598.c:59:5: warning: symbol 'ixgbe_get_pcie_msix_count_82598' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing the unused PAGE_USE_COUNT() macro. Also removing the unused
pages variable at ixgbe_configure_rx() function.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that our set_num_queues() routines for each feature are re-entrant, and
can be called at any point, they shouldn't zero out the feature's indices
or mask bits. Subsequent calls into those routines for those features can
result in zero Rx and Tx queues being assigned, causing a panic later in
driver reinitialization.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx Head writeback is causing multi-microsecond stalls on PCIe chipsets, due
to partial cacheline writebacks. Removing this feature removes these
issues.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flow control handling is overly complicated and difficult to maintain.
This patch cleans up the flow control handling and makes it much more
explicit. It also adds 1G flow control autonegotiation, for 1G copper
links, 1G KX links, and 1G fiber links.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ixgbe does not display the EEPROM version in ethtool -i, where
other drivers do. The EEPROM version is located at offset 0x29. This
patch adds support to display it.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code has some flaws in it when performing autonegotiation,
especially on KX/KX4 links. This patch updates the code to better handle
the autonegotiation states on link setup. The patch also removes a redundant
link configuration call on driver load, and moves link configuration to
the ->open() path.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code to determine the number of queues the device will want
on driver initialization is ugly and difficult to maintain. It also
doesn't allow for easy expansion for future features or future hardware.
This patch refactors these routines, and make them easier to deal with.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New year, new copyright date ranges. Also bump the driver version
number to reflect many of the recent changes.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our current MSI-X allocation mechanism does not support new hardware
at all. It also isn't getting the actual number of supported MSI-X vectors
from the device.
This patch allows the number of MSI-X vectors to be specific to a device,
plus it gets the number of MSI-X vectors available from PCIe configuration
space.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the device ID for BX devices using the 82598 MAC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And support for the KX/KX4 mezzanine card. Device id 0x10B6.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load times for NICs that use i2c to communicate with the phy were taking
~4.5 sec per port. This fix first checks to see if the link is already
up before calling get_link_capabilities, since if it is we don't need
query the phy for link state.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes ixgbe invoke the GRO hooks instead of LRO. As
GRO has a compatible external interface to LRO this is a very
straightforward replacement.
As GRO uses the napi structure to track the held packets, I've
modified the code paths involved to pass that along.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_off() is sufficient to stop Tx into the driver. Stopping the Tx
queues is redundant and unnecessary. By the same token, netif_carrier_on()
will be sufficient to re-enable Tx, so waking the queues is unnecessary.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register VLAN ID 0 so that frames with VLAN ID 0 are received and get
their tag stripped when ixgbe is not in DCB mode. VLAN ID 0 means
that the frame is 'priority tagged' only - it is not a VLAN, but the
priority value is the tag in valid. The functions
ixgbe_vlan_rx_register() and ixgbe_vlan_rx_kill_vid() were moved up a
couple functions to correct compiling issues with this change.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The is an issue where setting Relaxed Ordering (RO) bit
(in a PCI-E write transaction) on 82598 causing the chipset
to drop DCA hints. This patch forces RO not to be set for
descriptors as well as payload. This will only be in effect
while DCA is enabled and no performance difference was
noticed in testing.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The adapter rings are kcalloc()'d, but in set_ringparam() in ixgbe_ethtool,
we replace that memory from the vmalloc() pool. This can result in a NULL
pointer reference when trying to modify the rings at a later time, or on
device removal.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows DCB mode to change the number of queues, and presumably
the number of NAPI instances, safely.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this sparse warnings:
drivers/net/ixgbe/ixgbe_82598.c:180:5: warning: symbol 'ixgbe_get_copper_link_capabilities_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_82598.c:245:5: warning: symbol 'ixgbe_setup_fc_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_82598.c:729:5: warning: symbol 'ixgbe_set_vmdq_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_82598.c:773:5: warning: symbol 'ixgbe_set_vfta_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_82598.c:897:5: warning: symbol 'ixgbe_read_analog_reg8_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_82598.c:919:5: warning: symbol 'ixgbe_write_analog_reg8_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_82598.c:940:5: warning: symbol 'ixgbe_read_i2c_eeprom_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_82598.c:1000:5: warning: symbol 'ixgbe_get_supported_physical_layer_82598' was not declared. Should it be static?
drivers/net/ixgbe/ixgbe_dcb_82598.c💯5: warning: symbol 'ixgbe_dcb_config_packet_buffers_82598' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Priority flow contol statistics for Data Center Bridging (DCB) weren't
included in ethtool. This patch adds them.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the Backward Congestion Notification Address (BCNA) attribute to the
Backward Congestion Notification (BCN) interface for Data Center Bridging
(DCB), which was missing. Receive the BCNA attribute in the ixgbe driver.
The BCNA attribute is for a switch to inform the endstation about the physical
port identification in order to support BCN on aggregated links.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Data Center Bridging (DCB) had no way to know if setstate had failed in the
driver. This patch enables dcb netlink code to handle the status for the DCB
setstate interface. Likewise it allows the driver to return a failed status
if MSI-X isn't enabled.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was initially reported by Joerg Roedel <joerg.roedel@amd.com>
It appears that ixgbe has had a long standing bug where it was unmapping a different size than it had mapped.
ixgbe 0000:02:00.0: PCI-DMA: device driver frees DMA memory with different sizes than it mapped.
ixgbe 0000:02:00.0: PCI-DMA: device driver frees DMA memory with different size [device address=0x0000000003fed812] [map size=258 bytes] [unmap size=256 bytes]
Pid: 6178, comm: rmmod Not tainted 2.6.28-rc5 #4 Call Trace:
[<ffffffff8022a2ae>] iommu_queue_inv_iommu_pages+0x5e/0x70
[<ffffffff80225956>] check_unmap+0x1c6/0x240 [<ffffffff80225ff5>] debug_unmap_single+0xb5/0x110 [<ffffffffa0213997>] ixgbe_clean_rx_ring+0x147/0x220 [<ffffffffa0214d7d>] ixgbe_down+0x2fd/0x3d0 [ixgbe] [<ffffffffa02150b3>] ixgbe_close+0x13/0xc0 [ixgbe] [<ffffffff80431326>] dev_close+0x56/0xa0 [<ffffffff804313b3>] rollback_registered+0x43/0x220 [<ffffffff804315a5>] unregister_netdevice+0x15/0x60 [<ffffffff80431601>] unregister_netdev+0x11/0x20 [<ffffffffa021aef8>] ixgbe_remove+0x48/0x16e [ixgbe] [<ffffffff80386ffc>] pci_device_remove+0x2c/0x60 [<ffffffff803ef929>] __device_release_driver+0x99/0x100
[<ffffffff803efa48>] driver_detach+0xb8/0xc0 [<ffffffff803eea6e>] bus_remove_driver+0x8e/0xd0 [<ffffffff80387374>] pci_unregister_driver+0x34/0x90 [<ffffffff8026c6c7>] sys_delete_module+0x1c7/0x2a0 [<ffffffff802a9ce9>] do_munmap+0x349/0x390 [<ffffffff80374481>] __up_write+0x21/0x150 [<ffffffff8020c30b>] system_call_fastpath+0x16/0x1b
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the PCIe Advanced Error Reporting callbacks in
ixgbe. The 82598 hardware supports AER, so we enable it.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seems the ixgbe's code was copied from e1000.
The comment talks about something not exist.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe_init_interrupt_scheme() is called from ixgbe_resume(). Build that
with CONFIG_PM and without CONFIG_HOTPLUG and you've got a problem.
Several helpers called by it also are misannotated __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the netlink option for DCB is necessary to actually be useful,
simplified the Kconfig option. In addition, added useful help text for the
Kconfig option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove redundant argument comments in files of drivers/net/*
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for SFP+ PHY in the following device ID's (10DB,
10F1, 10E1). These SFP+ PHY's are accessed via an I2C interface so the
patch also includes functions to support this.
Another feature of note is that the PHY is pluggable and some
rearchitecting was needed to support this.
Signed-off-by: Donald Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds an interface to configure the Backward Congestion Notification
(BCN) feature. In a BCN capabale network, congestion notifications
from congested points out in the network can cause the end station
limit the rate of a given traffic flow.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a netlink interface for Data Center Bridging (DCB) to get and set
the enable state of the Priority Flow Control (PFC) feature.
Primarily, this is a way to turn off PFC in the driver while DCB
remains enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds interface for Data Center Bridging (DCB) to query (and set if
supported) the number of traffic classes currently supported by the
device for the two (DCB) features: priority groups (PG) and priority
flow control (PFC).
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds to the netlink interface for Data Center Bridging (DCB), allowing
the DCB capabilities supported by a device to be queried.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for Data Center Bridging (DCB) features in the ixgbe
driver and adds an rtnetlink interface for configuring DCB to the
kernel. The DCB feature support included are Priority Grouping (PG) -
which allows bandwidth guarantees to be allocated to groups to traffic
based on the 802.1q priority, and Priority Based Flow Control (PFC) -
which introduces a new MAC control PAUSE frame which works at
granularity of the 802.1p priority instead of the link (IEEE 802.3x).
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to network device ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] drivers/net/ixgbe/ixgbe_main.o
drivers/net/ixgbe/ixgbe_main.c: In function `ixgbe_intr':
drivers/net/ixgbe/ixgbe_main.c:1290: sorry, unimplemented: inlining failed in call to 'ixgbe_irq_enable': function body not available
drivers/net/ixgbe/ixgbe_main.c:1312: sorry, unimplemented: called from here
make[4]: *** [drivers/net/ixgbe/ixgbe_main.o] Error 1
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_off() is sufficient to stop Tx into the driver. Stopping the Tx
queues is redundant and unnecessary. By the same token, netif_carrier_on()
will be sufficient to re-enable Tx, so waking the queues is unnecessary.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel is currently shipping support for adapters with a phy
that does 10GBase-T (copper), which is 10 Gigabit ethernet
over standard Category 6 cabling.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot select INTEL_IOATDMA in Kconfig as soon as MYRI10GE or IXGBE
is enabled since the former is not available on all architectures.
Just use a Kconfig bool {IXGBE,MYRI10GE}_DCA set to =y when DCA
support can actually be built.
[myri10ge portion written and signed-off-by] Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch cleans up some whitespace items, reorders a couple of functions, and removes some outdated comments.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch corrects support for NAPI so that queues are correctly added and
removed during suspend/resume in the event that the number of MSI-X vectors
changes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch cleans up a bit of whitespace issues with the driver, updates
the copyright information, and bumps the version number up.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgbe_xmit_frame can be refactored to use fewer locals and better
utilize common kernel macros.
also fixed minor buglet with internal to driver vlan flag variable being
passed incorrectly.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
some functions were un-necessarily using local variables.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is partial preparation for a future patch which will extend
ixgbe_set_num_queues
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
clean up the hardware shutdown sequence to prevent hardware
from continuing to send when resetting or unloading.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a massive update that includes infrastructure for further patches
where we will add support for more phy types and eeprom types.
This code is shared as much as possible with other drivers, so the code may
seem a little obtuse at times but wherever possible we keep to the linux
style and methods.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
in some configurations there can be more than one rx queue per vector
in msi-x mode. Add functionality to be able to clean this without
changing the performance path single-rx-queue cleanup.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
changing ring sizes in ethtool needs to be robust. If an allocation fails the
driver must continue operation, with the previous settings.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
most of the time we only need 1500 bytes for a packet which means
we don't need a whole 4k page for each packet. Share the allocation
by using a reference count to the page and giving half to two
receive descriptors. This can enable us to use packet split mode
all the time due to the performance increase of allocating half
the pages.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
when using more than 8 tx queues you can overrun the 8 bit v_idx
field, so change it to 16 bits to represent the maximum number
of queues (one for each bit)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgbe was incorrectly setting the throttle rate setting for all tx
queues and the driver has been refreshed to better handle a dynamic
interrupt mode as well as multiple queues.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ethtool was not disabling the correct netif flags when setting
checksum disable.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
1) reading some of the registers in our hardware causes them to clear,
so don't read ICR in the ethtool register dump function.
2) several register iterators were not iterating
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Upon review a buglet was found where link change was not causing
an immediate link change event as it should.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch updates the link_up code and watchdog thread so that link_up
doesn't cause stack overflows due to long waits in interrupt context.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
after the most recent patches, the driver was not using the
correct iterator for updating the receive address registers (RAR)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This change makes it so only one srrctl register is programmed per VMDq id, and if VMDq is not enabled it is one register per RSS queue. Currently this function is working correctly for the multiqueue RSS and single queue cases, but if any advances features such as VMDq or DCB would have been enabled this function would have caused issues as it was not correct.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change TSO offloads to use a different context than VLAN insertion
and Tx checksumming. Hardware has separate registers internally for
storing these so use them.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
hardware was configured incorrectly which led all hints to be
sent to queue[0]'s DCA configuration.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
DCA related fixes
=================
- ixgbe was not compiling and using DCA correctly if dca was a module
- DCA interface changed with new kernel
- ixgbe was not correctly configured to indicate DCA hints to the
correct CPU.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
as mentioned by Herbert, our hardware supports IP offloads, not full
checksum offloads for any protocol in existence (even though the
hardware just provides generic csum support over any range of bytes)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This locks the seed down so loading/unloading the driver will present
predictable hashing from RSS. Also move the rx_buf_len out of the adapter
struct, and into the Rx ring struct.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable Tx Head Writeback in the hardware. This helps performance by
removing adapter writebacks to descriptors on transmit completion.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since the adapter cannot tell what the remote end's flow control capability
is through auto-neg, we must turn off flow control by default.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cleanup all the different references to the Tx ring and Rx ring structures
and make them common across the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement HAVE_SET_RX_MODE in the driver for MC and UC lists.
Signed-off-by: Christopher Leech <christopher.leech@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
the driver was misinterpreting rx_csum return value in the descriptor
so occassionally we would indicate an rx_csum error in our stats
when there was none. This would have no effect on traffic because
we would just hand the packet to the stack anyway without the offload
flag set, but would increase CPU for those packets that needed a recompute.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This commit dropped the setting of the default interrupt throttle rate.
commit 021230d40a
Author: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Date: Mon Mar 3 15:03:45 2008 -0800
ixgbe: Introduce MSI-X queue vector code
The following patch adds it back. Without this the default value of 0
causes the performance of this card to be awful. Restoring these to the
default values yields much better performance.
This regression has been around since 2.6.25.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: stable@kernel.org [2.6.25 and later]
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
VLAN filtering is broken, due to reading the incorrect register for
the VLAN filtering settings. Fixed by reading/writing the correct
register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a simple device ID add for adapters that support
CX4 (copper infiniband style cable) connectors for 10GbE.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ixgbe driver was untested with device ID 8086:10c8 but still advertises
support. Currently if this device is present in the system when the driver
is loaded, the system will panic.
Remove this device ID until full support can be tested with available
hardware. This patch is necessary for 2.6.24, 2.6.25 and 2.6.26
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With the recent changes to tx mutiqueue, igb/ixgbe/e1000e was not calling
netif_tx_start_all_queues() before calling netif_tx_wake_all_queues().
This causes an issue during loading of the driver.
In addition, updated e1000e to use the updated tx mutliqueue api.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This effectively "flips the switch" by making the core networking
and multiqueue-aware drivers use the new TX multiqueue structures.
Non-multiqueue drivers need no changes. The interfaces they use such
as netif_stop_queue() degenerate into an operation on TX queue zero.
So everything "just works" for them.
Code that really wants to do "X" to all TX queues now invokes a
routine that does so, such as netif_tx_wake_all_queues(),
netif_tx_stop_all_queues(), etc.
pktgen and netpoll required a little bit more surgery than the others.
In particular the pktgen changes, whilst functional, could be largely
improved. The initial check in pktgen_xmit() will sometimes check the
wrong queue, which is mostly harmless. The thing to do is probably to
invoke fill_packet() earlier.
The bulk of the netpoll changes is to make the code operate solely on
the TX queue indicated by by the SKB queue mapping.
Setting of the SKB queue mapping is entirely confined inside of
net/core/dev.c:dev_pick_tx(). If we end up needing any kind of
special semantics (drops, for example) it will be implemented here.
Finally, we now have a "real_num_tx_queues" which is where the driver
indicates how many TX queues are actually active.
With IGB changes from Jeff Kirsher.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for a feature bit for something that
can be tested by simply checking the TX queue count.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently VLAN filtering is enabled when the first VLAN is added.
Obviously before that there's no point in receiving any VLAN packets.
Now that we disable VLAN filtering in promiscous mode, we can keep
the VLAN filters enabled the remaining time.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discussed in this thread:
http://www.mail-archive.com/netdev@vger.kernel.org/msg53976.html
promiscous mode means to disable *all* filters. Currently only unicast
and multicast filtering is disabled. This patch changes all Intel
drivers to also disable VLAN filtering.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEh is not recovering in a resonable amount of time on PPC during
ixgbe_down().
Signed-off-by: Paul Larson <pl@us.ibm.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Support for in-kernel LRO with the ability to enable/disable via ethtool
based on comments from Ben Hutchings.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using the new interface for propagating device feature flags into VLAN
devices, turn on TSO and CSUM offload on VLAN devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
To enable EEH support for pci-express network adapters, pcie/msi state
needs to be saved and restored for that adapter.
Tested this EEH patch with Intel 10G pci-express ixgbe adapter.
Signed-off-by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Under CONFIG_DCA the compilation is broken since the commit
bd0362dde0 (ixgbe: Add optional
DCA infrastructure).
IXGBE_SUCCESS is not defined anywhere, replace it with 0.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
82598 cards and up support DCA, which enables the chipset to warm
up the caches for upcoming payload data. This code makes the
driver plug into the CONFIG_DCA infrastructure that was merged
earlier.
Signed-off-by: Jeb Cramer <cramerj@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
82598 can produce a formidable interrupt rate, and is largely
unusable without some form of moderation. The default behaviour
before this patch is to limit irq's to a reasonable number.
However, just like our other drivers we can reduce latency
for small packet-type traffic considerably by allowing the
irq rate to go up dynamically.
This patch introduces a simple irq moderation algorithm based
on traffic analysis. The driver will use more CPU to service
small packets quicker but will perform the same on bulk traffic
as the old code.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that the irq vector code is in place, we can add the conditional
multiqueue TX code in the driver. This requires the optional
CONFIG_NETDEVICES_MULTIQUEUE=y and will not be enabled without
it.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Waskiewicz Jr, Peter P <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This code abstracts the per-queue MSI-X interrupt vector into
a queue vector layer. This abstraction is needed since there can
be many more queues than available MSI-X vectors in a machine.
The MSI-X irq vectors are remapped to a shared queue vector which
can point to several (both RX and TX) hardware queues. The NAPI
algorithm then cleans the appropriate ring/queues on interrupt
or poll.
The remapping is a delicate and complex calculation to make sure
that we're not unbalancing the irq load, and spreads the irqs
as much as possible, and may combine RX and TX flows onto the
same queue vector.
This effectively enables receive flow hashing across vectors
and helps irq load balance across CPUs.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Waskiewicz Jr, Peter P <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In reply to "RE: [Fwd: [PATCH 2.6.25] ixgbe/igb: correctly obtain protocol
information on transmit]" from Andy Gospodarek:
The driver was incorrectly looking at socket headers for
protocol information, needed for checksumming offload. Fix
this by not looking at the socket but frame headers instead.
This disregards extension headers but it's unclear that linux
generates those anyway.
Tested by Andy Gospodarek.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It's easy to oversee this issue when working with this card
as evrything will work OK but performance is severely limited
(something like 1.5gbit on a x1 link) if the pci-express
slot does not offer more bandwidth.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Just like our other drivers before we can switch ixgbe to
provide real-time packet/byte counters to the stack easily.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several counters behave differently on 82598 causing them to display
incorrect values. Adjust the accounting so the reported numbers
make sense and do not double count or represent the wrong item.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We were not returning CHECKSUM_NONE in a lot of cases which is
wrong. Move common exit points in this function and error code
up before the actual work in this function.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A gap was left in the FW release/grab code in up/down path. Fix
it by making the release/grab code a function and calling it in
appropriate locations.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The i82598 can support various media types but this ethtool
code only was coded for fiber just yet.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This ports Herbert Xu's "maybe_stop_tx" code and removes the tx_lock
which is not needed.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After testing we confirmed that the irq_sem can safely be
removed from ixgbe.
Add strict state checking code to various ethtool parts to
properly protect against races between various driver reset
paths.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
While cleaning up the internal API focussing on Fiber and CX4 code
we found that I had broken the copper PHY initialization code. This
patch restores the PHY-specific code. This is mostly uninteresting
since no copper PHY boards are yet available. The changes have been
tested against Fiber only as I do not even have copper PHY versions
of 82598 macs.
This change actually cleans up the API code a bit more and we
lose some initialization code. A few PHY link detection helper
lines of code have been snuck into this patch, as well as a
read flush where it was suspected that this might cause issues.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* use irq_handler_t where appropriate
* no need to use 'irq' function arg, its already stored in a data struct
* rename irq handler 'irq' argument to 'dummy', where the function
has been analyzed and proven not to use its first argument.
* remove always-false "dev_id == NULL" test from irq handlers
* remove pointless casts from void*
* declance: irq argument is not const
* add KERN_xxx printk prefix
* fix minor whitespace weirdness
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several of the Intel ethernet drivers keep an atomic counter used to
manage when to actually hit the hardware with a disable or an enable.
The way the net_rx_work() breakout logic works during a pending
napi_disable() is that it simply unschedules the poll even if it
still has work.
This can potentially leave interrupts disabled, but that is OK
because all of the drivers are about to disable interrupts
anyways in all such code paths that do a napi_disable().
Unfortunately, this trips up the semaphore used here in the Intel
drivers. If you hit this case, when you try to bring the interface
back up it won't enable interrupts. A reload of the driver module
fixes it of course.
So what we do is make sure all the sequences now go:
napi_disable();
atomic_set(&adapter->irq_sem, 0);
*_irq_disable();
which makes sure the counter is always in the correct state.
Reported by Robert Olsson.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression added by changeset
53e52c729c ("[NET]: Make ->poll()
breakout consistent in Intel ethernet drivers.")
As pointed out by Jesse Brandeburg, for three of the drivers edited
above there is breakout logic in the *_clean_tx_irq() code to prevent
running TX reclaim forever. If this occurs, we have to elide NAPI
poll completion or else those TX events will never be serviced.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
This makes the ->poll() routines of the E100, E1000, E1000E, IXGB, and
IXGBE drivers complete ->poll() consistently.
Now they will all break out when the amount of RX work done is less
than 'budget'.
At a later time, we may want put back code to include the TX work as
well (as at least one other NAPI driver does, but by in large NAPI
drivers do not do this). But if so, it should be done consistently
across the board to all of these drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Drivers do this to try to break out of the ->poll()'ing loop
when the device is being brought administratively down.
Now that we have a napi_disable() "pending" state we are going
to solve that problem generically.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make strings const if possible, and fix includes so forward definitions
are seen.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Intel 82598 PCI-Express 10GbE
chipset. Devices will be available on the market soon.
This version of the driver is largely the same as the last release:
* Driver uses a single RX and single TX queue, each using 1 MSI-X
irq vector.
* Driver runs in NAPI mode only
* Driver is largely multiqueue-ready (TM)
Changes since 20070803:
* removed wrappers for hardware functions
* incorporated e1000e-style HW api reorganization code
* sparse/checkpatch cleanups, namespace cleanups
* driver prints out extra debugging information at load time
identifying adapter board number, mac, phy types
* removed ixgbe_api.c, ixgbe_api.h, ixgbe_osdep.h
* driver update to 1.1.18
* removed ixgbe.txt which contained no useful info anymore
[ Integrated napi_struct changes from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>