Change dsi_vc_config_l4/vp() to loop for the VC_BUSY flag to change, and
return an error if it fails.
Busy looping is bad, but there's no interrupt that can be used for all the
cases where VC can be busy. So the caller should first try to make sure
that the VC is not busy, if possible, and then call dsi_vc_config_l4/vp().
Most notable case when the caller cannot be sure if the VC is busy is
after frame has been sent. Usually DSI buffers have been emptied until we
need to reconfig the VC, but in some rare cases the VC can still be busy,
and this patch will handle that case.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Once the DSI PLL is separated from the DSI display a full DSI reset will
not be performed every time the display is enabled so the interface and
VCs must be disabled when disabling the display. If the VCs are not
disabled some register accesses will abort.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The TRM tells us to wait for the DSI PLL derived clocks to become
active before selecting them for use. I didn't actually have any issues
which this would fix but according to the TRM it seems to be the right
thing to do.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Print an error message if dsi_calc_clock_rates() fails just like it's
done when dispc_calc_clock_rates() fails.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Do not leave the free running pixel clock enabled if the DSI PLL reset
times out.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The OCTEON is a MIPS64 based SOC family with an on chip watchdog unit.
The driver is split into two source files one for the C code and one
for assembly. Assembly is needed to handle the NMI and then print the
machine state before the reboot is triggered.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Marc Zyngier <maz@misterjones.org>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
To: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org,
Patchwork: https://patchwork.linux-mips.org/patch/1503/
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 drivers/watchdog/octeon-wdt-main.c
create mode 100644 drivers/watchdog/octeon-wdt-nmi.S
au1000_eth uses firmware calls to get a valid MAC address, and changes
it depending on platform device id. This patch moves this logic out of
the driver into the platform device registration part, where boards with
supported chips can use whatever firmware interface they need; the default
implementation maintains compatibility with existing, YAMON-based firmware.
Tested-by: Wolfgang Grandegger <wg@denx.de>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1481/
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the SERIAL_8250_AU1X00 config symbol. Instead, use the MIPS_ALCHEMY
one which is always defined when building an Au1x00-based platform.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Linux-serial <linux-serial@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This one depends on a previous patch (which removes SOC_AU1X00 and changes
MACH_ALCHEMY) to apply cleanly (and then actually work), so I'd love for
this to go in via the mips tree.
Remove the CONFIG_SOC_AU1X00 Kconfig symbol since its job can also be done
by MACH_ALCHEMY, now renamed to MIPS_ALCHEMY.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
request_region should be used with release_region, not request_mem_region.
Geert Uytterhoeven pointed out that in the case of drivers/video/gbefb.c,
the problem is actually the other way around; request_mem_region should be
used instead of request_region.
The semantic patch that finds/fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r1@
expression start;
@@
request_region(start,...)
@b1@
expression r1.start;
@@
request_mem_region(start,...)
@depends on !b1@
expression r1.start;
expression E;
@@
- release_mem_region
+ release_region
(start,E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
atc_chain_complete shall be called with atchan->lock held
and bh disabled.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use {read|write}l instead of __raw_{read|write}l since PCH DMA
controller is PCI device.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
I often use "ethtool -i" command to check what driver controls the
ehternet device. But because current virtio_net driver doesn't
support "ethtool -i", it becomes the following:
# ethtool -i eth3
Cannot get driver information: Operation not supported
This patch simply adds the "ethtool -i" support. The following is the
result when using the virtio_net driver with my patch applied to.
# ethtool -i eth3
driver: virtio_net
version: N/A
firmware-version: N/A
bus-info: virtio0
Personally, "-i" is one of the most frequently-used option, and most
network drivers support "ethtool -i", so I think virtio_net also
should do.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use ARRAY_SIZE)
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPP channel ops structure should be const.
Cleanup the declarations to use standard C99 format.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the availablility of a sysfs device attribute for examining disk serial
numbers the ioctl is no longer needed. The user-space changes for this aren't
upstream yet so we don't have any users to worry about.
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Create a new attribute for virtio-blk devices that will fetch the serial number
of the block device. This attribute can be used by udev to create disk/by-id
symlinks for devices that don't have a UUID (filesystem) associated with them.
ATA_IDENTIFY strings are special in that they can be up to 20 chars long
and aren't required to be nul-terminated. The buffer is also zero-padded
meaning that if the serial is 19 chars or less that we get a nul-terminated
string. When copying this value into a string buffer, we must be careful to
copy up to the nul (if it present) and only 20 if it is longer and not to
attempt to nul terminate; this isn't needed.
Changes since v1:
- Added BUILD_BUG_ON() for PAGE_SIZE check
- Removed min() since BUILD_BUG_ON() handles the check
- Replaced serial_sysfs() by copying id directly to buffer
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: john cooper <john.cooper@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If we want to support barriers with the cache=writethrough mode in qemu
we need to tell the block layer that we only need queue drains to
implement a barrier. Follow the model set by SCSI and IDE and assume
that there is no volatile write cache if the host doesn't advertize it.
While this might imply working barriers on old qemu versions or other
hypervisors that actually have a volatile write cache this is only a
cosmetic issue - these hypervisors don't guarantee any data integrity
with or without this patch, but with the patch we at least provide
data ordering.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This restricts the use of the big kernel lock to the i830 and i810
device drivers. The three remaining users in common code (open, ioctl
and release) get converted to a new mutex, the drm_global_mutex,
making the locking stricter than the big kernel lock.
This may have a performance impact, but only in those cases that
currently don't use DRM_UNLOCKED flag in the ioctl list and would
benefit from that anyway.
The reason why i810 and i830 cannot use drm_global_mutex in their
mmap functions is a lock-order inversion problem between the current
use of the BKL and mmap_sem in these drivers. Since the BKL has
release-on-sleep semantics, it's harmless but it would cause trouble
if we replace the BKL with a mutex.
Instead, these drivers get their own ioctl wrappers that take the
BKL around every ioctl call and then set their own handlers as
DRM_UNLOCKED.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
In most use cases the driver will be using the same static config all
the time: interpreting i2c_board_info::platform_data as the default
config we can can save the GPU driver a redundant set_config() call.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
free_netdev finally calls kfree which makes the contents
of ndev and priv (private data contained in ndev) invalid.
So iounmap should be called before free_netdev.
Cc: David S. Miller <davem@davemloft.net>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sriramakrishnan <srk@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize tasklet before interrupts are requested to prevent
scheduling of an uninitialized tasklet.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is required should we ever attempt to use an io-mapping where
KM_USER0 is verboten, such as inside an IRQ context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
R4xx also uses the atom add connector function, but underscan is only
supported on avivo chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
v2: Userspace (notably xf86-video-{intel,ati}) became confused when
drmSetInterfaceVersion() started returning -EBUSY as they used a second
call (the first done in drmOpen()) to check their master credentials.
Since userspace wants to be able to repeatedly call
drmSetInterfaceVersion() allow them to do so.
v3: Rebase to drm-core-next.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (30 commits)
Revert "HID: add support for the Wacom Intuos 4 wireless"
HID: fix up Kconfig entry for ACRUX driver
HID: add ACRUX game controller force feedback support
HID: Force input registration for "VEC footpedal"
HID: add HID_QUIRK_HIDINPUT_FORCE
HID: hid-input.c: indentation fixes
HID: hiddev: use usb_find_interface, get rid of BKL
HID: ignore digitizer usage Undefined (0x00)
HID: Add support for Conceptronic CLLRCMCE
HID: hid-ids.h: Whitespace fixup, align using TABs
HID: picolcd: implement refcounting of framebuffer
HID: picolcd: do not reallocate memory on depth change
HID: picolcd: Add minimal palette required by fbcon on 8bpp
HID: magicmouse: Correct parsing of large X and Y motions.
HID: magicmouse: report last touch up
HID: picolcd: fix deferred_io init/cleanup to fb ordering
HID: hid-ids.h: keep vendor ids in alphabetical order
HID: add proper support for Elecom BM084 bluetooth mouse
HID: magicmouse: enable horizontal scrolling
HID: magicmouse: add param for scroll speed
...
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (39 commits)
random: Reorder struct entropy_store to remove padding on 64bits
padata: update API documentation
padata: Remove padata_get_cpumask
crypto: pcrypt - Update pcrypt cpumask according to the padata cpumask notifier
crypto: pcrypt - Rename pcrypt_instance
padata: Pass the padata cpumasks to the cpumask_change_notifier chain
padata: Rearrange set_cpumask functions
padata: Rename padata_alloc functions
crypto: pcrypt - Dont calulate a callback cpu on empty callback cpumask
padata: Check for valid cpumasks
padata: Allocate cpumask dependend recources in any case
padata: Fix cpu index counting
crypto: geode_aes - Convert pci_table entries to PCI_VDEVICE (if PCI_ANY_ID is used)
pcrypt: Added sysfs interface to pcrypt
padata: Added sysfs primitives to padata subsystem
padata: Make two separate cpumasks
padata: update documentation
padata: simplify serialization mechanism
padata: make padata_do_parallel to return zero on success
padata: Handle empty padata cpumasks
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (276 commits)
[SCSI] zfcp: Trigger logging in the FCP channel on qdio error conditions
[SCSI] zfcp: Introduce experimental support for DIF/DIX
[SCSI] zfcp: Enable data division support for FCP devices
[SCSI] zfcp: Prevent access on uninitialized memory.
[SCSI] zfcp: Post events through FC transport class
[SCSI] zfcp: Cleanup QDIO attachment and improve processing.
[SCSI] zfcp: Cleanup function parameters for sbal value.
[SCSI] zfcp: Use correct width for timer_interval field
[SCSI] zfcp: Remove SCSI device when removing unit
[SCSI] zfcp: Use memdup_user and kstrdup
[SCSI] zfcp: Fix retry after failed "open port" erp action
[SCSI] zfcp: Fail erp after timeout
[SCSI] zfcp: Use forced_reopen in terminate_rport_io callback
[SCSI] zfcp: Register SCSI devices after successful fc_remote_port_add
[SCSI] zfcp: Do not try "forced close" when port is already closed
[SCSI] zfcp: Do not unblock rport from REOPEN_PORT_FORCED
[SCSI] sd: add support for runtime PM
[SCSI] implement runtime Power Management
[SCSI] convert to the new PM framework
[SCSI] Unify SAM_ and SAM_STAT_ macros
...
* upstream/pvhvm:
Introduce CONFIG_XEN_PVHVM compile option
blkfront: do not create a PV cdrom device if xen_hvm_guest
support multiple .discard.* sections to avoid section type conflicts
xen/pvhvm: fix build problem when !CONFIG_XEN
xenfs: enable for HVM domains too
x86: Call HVMOP_pagetable_dying on exit_mmap.
x86: Unplug emulated disks and nics.
x86: Use xen_vcpuop_clockevent, xen_clocksource and xen wallclock.
xen: Fix find_unbound_irq in presence of ioapic irqs.
xen: Add suspend/resume support for PV on HVM guests.
xen: Xen PCI platform device driver.
x86/xen: event channels delivery on HVM.
x86: early PV on HVM features initialization.
xen: Add support for HVM hypercalls.
Conflicts:
arch/x86/xen/enlighten.c
arch/x86/xen/time.c
* upstream/core:
xen/panic: use xen_reboot and fix smp_send_stop
Xen: register panic notifier to take crashes of xen guests on panic
xen: support large numbers of CPUs with vcpu info placement
xen: drop xen_sched_clock in favour of using plain wallclock time
pvops: do not notify callers from register_xenstore_notifier
xen: make sure pages are really part of domain before freeing
xen: release unused free memory
Currently register_xenstore_notifier notifies the caller during the
registration itself if xenstore is believed to be ready. This behaviour
causes problems to PV on HVM guests, in which case callers should be
notified by xenbus_probe only after the platform pci driver is loaded.
We already make sure xenbus_probe is called at the right time, calling
it either from device_initcall (PV case) or from the platform pci
driver initialization (HVM case) so we don't need this additional
notification.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
'cnt' is unsigned, so this code may become wrong in future as
dmatest_add_threads() can return error code:
cnt = dmatest_add_threads(dtc, DMA_MEMCPY);
thread_count += cnt > 0 ? cnt : 0;
^^^^^^^
Now it can return only -EINVAL if and only if second argument of
dmatest_add_threads() is not one of DMA_MEMCPY, DMA_XOR, DMA_PQ.
So, now it is not wrong but may become wrong in future.
The semantic patch that finds this problem (many false-positive results):
(http://coccinelle.lip6.fr/)
// <smpl>
@ r1 @
identifier f;
@@
int f(...) { ... }
@@
identifier r1.f;
type T;
unsigned T x;
@@
*x = f(...)
...
*x > 0
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
On some platforms (MacPro3,1) the BIOS assigns the ioatdma device to the
incorrect iommu causing faults when the driver initializes. Add a quirk
to catch this misconfiguration and try falling back to untranslated
operation (which works in the MacPro3,1 case).
Assuming there are other platforms with misconfigured iommus teach the
ioatdma driver to treat initialization failures as non-fatal (just fail
the driver load and emit a warning instead of triggering a BUG_ON).
This can be classified as a boot regression since 2.6.32 on affected
platforms since the ioatdma module did not autoload prior to that
kernel.
Cc: <stable@kernel.org>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Reported-by: Chris Li <lkml@chrisli.org>
Tested-by: Chris Li <lkml@chrisli.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This extends the DMA engine driver for the COH 901 318 used in the
U300 platform with the generic runtime slave control command.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This extends the DMA engine driver for the DMA40 used in the
U8500 platform with the generic runtime slave configuration
interface.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Topcliff PCH is the platform controller hub that is going to
be used in Intel's upcoming general embedded platforms. This
adds the driver for Topcliff PCH DMA controller. The DMA
channels are strictly for device to host or host to device
transfers and cannot be used for generic memcpy.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
[kill GFP_ATOMIC, kill __raw_{read|write}l, locking fixlet]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Export req_lim via sysfs for debugging.
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Acked-by: David Dillow <dave@thedillows.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
82ca934176 added scary looking
but harmless error messages. Make them clearer and make the
actual failure message show up with the same severity as the
harmless one.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If kzalloc() fails return with -ENOMEM from ipw2100_net_init() which is
called by register_netdev.
CC: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_rx_skb_preprocess nulls rxs and the mactime is never set again -
mactime is always 0. This causes problems in IBSS mode.
ieee80211_rx_bss_info uses mactime to decide if an IBSS merge is needed.
Without this patch the merge is triggered by each beacon received.
This can be recognized by the "beacon TSF higher than local TSF - IBSS
merge with BSSID" log message accompanying each beacon.
This problem was not completely fixed in commit
a6d2055b02 and is not a stable kernel fix.
It is solely intended for wireless-testing.
Signed-off-by: Jan Friedrich <jft@dev2day.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SMC2802W appears to work with p54pci.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: David Cozatt <olbrannon@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed a possible issue in the paused flag management of the
ath_atx_tid data structure. In particular, in a noisy environment and
under heavy load, I observed that the AGGR session establishment could
fail several times consecutively causing values of the paused flag
greater than one for this TID (ath_tx_pause_tid is called more than
once from ath_tx_aggr_start).
Considering that the session for this TID can not be established also
after the mac80211 stack calls the ieee80211_agg_tx_operational() since
the ath_tx_aggr_resume() lowers the paused flag only by one.
This patch also replaces some BUG_ON calls with WARN_ON, as even if
these unlikely conditions happen, it's not fatal enough to justify a
BUG_ON.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 was not relying on the CTL indexes from the EEPROM for capping the
max output power. The CTL indexes from the EEPROM provide calibrated
limits for output power for each tested and supported frequency. Without
this the device operates at a power level which only conforms to the
transmit spectrum mask as specified by IEEE Annex I.2.3.
The regulatory limit by CRDA is always used but does not provide
calibrated values for optimal performance, specially on band edges.
Using the calibrated data from the EEPROM ensures the device
operates at optimal output power while still ensuring proper
regulatory compliance. The device uses the minimum of these tree
values, the value from CRDA, the calibrated value from CTL indexex,
and the value to conform to the IEEE transmit spectrum mask.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1271_dump() uses cmd after kfree(cmd). Move kfree() just after
wl1271_dump().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
small typo fix in ucode_bt_stats_read debugfs file
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is a uCode bug which cause the tx queue id not match scd_flow
in compressed block ack frame, and it need to be addressed in uCode.
Currently, driver will log the information when it happen.
Since it is possible happen very often and we do not want to fill the syslog,
so don't enable the logging by default.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When iwlwifi is compiled w/o debug, we get
this warning:
iwl-agn.c: In function ‘iwlagn_load_firmware’:
iwl-agn.c:2014: warning: passing argument 3 of ‘iwl_print_hex_dump’ discards qualifiers from pointer target type
iwl-debug.h:73: note: expected ‘void *’ but argument is of type ‘const u8 *’
because the const qualifier is missing in the
inline stub. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR5008-AR9002, other forms of calibration must not be started while
the noise floor calibration is running, as this can create invalid
readings which were sometimes not even recoverable by any further
calibration attempts.
This patch also ensures that the result of noise floor measurements
are processed faster and also allows the result of the initial
calibration on reset to make it into the NF history buffer
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noise floor history buffer is currently not kept per channel, which
can lead to problems when changing channels from a clean channel to a
noisy one. Also when switching from HT20 to HT40, the noise floor
history buffer is full of measurements, but none of them contain data
for the extension channel, which it needs quite a bit of time to recover
from.
This patch puts all the per-channel calibration data into a single data
structure, and gives the the driver control over whether that is used
per-channel or even not used for some channels.
For ath9k_htc, I decided to keep this per-channel in order to avoid
creating regressions.
For ath9k, the data is kept only for the operating channel, which saves
some space. ath9k_hw takes care of wiping old data when the operating
channel or its channel flags change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the software scan callback was used to indicate to the hardware,
when it was safe to calibrate. This didn't really work properly, because it
depends on a specific order of software scan callbacks vs. channel changes.
Also, software scans are not the only thing that triggers off-channel
activity, so it's better to use the newly added indication from mac80211 for
this and not use the software scan callback for anything calibration related.
This fixes at least some of the invalid noise floor readings that I've seen
in AP mode on AR9160
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writes to the analog shift registers, which are issues by the initval
programming function, require a 100 usec delay (similar to AR9002,
but in a different register range).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When updating the PAPRD table in hardware, PAPRD itself needs to be
disabled first, otherwise the hardware can throw a data bus error,
which upsets at least some platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The periodic noise floor calibration is broken on this chip family, because
it keeps triggering a software-filtered noise floor calibration, but never
reads the result before uploading the history buffer value to the hardware.
Fix this with a call to ath9k_hw_getnf(), just like on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9003 the initial noise floor calibration is currently triggered
at the end of the reset without allowing the hardware to update the
baseband settings. This could potentially make scans in noisy
environments a bit more unreliable, so use the same calibration
sequence that is used on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit f84b29ec0a
Author: Johannes Berg <johannes.berg@intel.com>
Date: Tue May 18 02:29:13 2010 -0700
iwlwifi: queue user-initiated scan when doing internal scan
introduced a potential deadlock because it calls
ieee80211_scan_completed() with the priv->mutex
held, but mac80211 may call back into iwlwifi
which would lead to recursive locking. Move this
out from under the mutex.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
phy/marvell: add 88ec048 support
igb: Program MDICNFG register prior to PHY init
e1000e: correct MAC-PHY interconnect register offset for 82579
hso: Add new product ID
can: Add driver for esd CAN-USB/2 device
l2tp: fix export of header file for userspace
can-raw: Fix skb_orphan_try handling
Revert "net: remove zap_completion_queue"
net: cleanup inclusion
phy/marvell: add 88e1121 interface mode support
u32: negative offset fix
net: Fix a typo from "dev" to "ndev"
igb: Use irq_synchronize per vector when using MSI-X
ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
e1000e: Fix irq_synchronize in MSI-X case
e1000e: register pm_qos request on hardware activation
ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
net: Add getsockopt support for TCP thin-streams
cxgb4: update driver version
cxgb4: add new PCI IDs
...
Manually fix up conflicts in:
- drivers/net/e1000e/netdev.c: due to pm_qos registration
infrastructure changes
- drivers/net/phy/marvell.c: conflict between adding 88ec048 support
and cleaning up the IDs
- drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
conflict (registration change vs marking it static)
The current strategy in ib_srp for posting receive buffers is:
* Post one buffer after channel establishment.
* Post one buffer before sending an SRP_CMD or SRP_TSK_MGMT to the target.
As a result, only the first non-SRP_RSP information unit from the
target will be processed. If that first information unit is an
SRP_T_LOGOUT, it will be processed. On the other hand, if the
initiator receives an SRP_CRED_REQ or SRP_AER_REQ before it receives a
SRP_T_LOGOUT, the SRP_T_LOGOUT won't be processed.
We can fix this inconsistency by changing the strategy for posting
receive buffers to:
* Post all receive buffers after channel establishment.
* After a receive buffer has been consumed and processed, post it again.
A side effect is that the ib_post_recv() call is moved out of the SCSI
command processing path. Since __srp_post_recv() is not called
directly any more, get rid of it and move the code directly into
srp_post_recv(). Also, move srp_post_recv() up in the file to avoid a
forward declaration.
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Acked-by: David Dillow <dave@thedillows.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft-2.6:
ibft: Use IBFT_SIGN instead of open-coding the search string.
ibft: convert iscsi_ibft module to iscsi boot lib
ibft: separate ibft parsing from sysfs interface
ibft: For UEFI machines actually do scan ACPI for iBFT.
ibft: Update iBFT handling for v1.03 of the spec.
Replace an open-coded dump of the receive buffer with a call to
print_hex_dump().
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Runtime: Add runtime PM statistics (v3)
PM / Runtime: Make runtime_status attribute not debug-only (v. 2)
PM: Do not use dynamically allocated objects in pm_wakeup_event()
PM / Suspend: Fix ordering of calls in suspend error paths
PM / Hibernate: Fix snapshot error code path
PM / Hibernate: Fix hibernation_platform_enter()
pm_qos: Get rid of the allocation in pm_qos_add_request()
pm_qos: Reimplement using plists
plist: Add plist_last
PM: Make it possible to avoid races between wakeup and system sleep
PNPACPI: Add support for remote wakeup
PM: describe kernel policy regarding wakeup defaults (v. 2)
PM / Hibernate: Fix typos in comments in kernel/power/swap.c
Change abbreviated IB_QPT_RAW_ETY to IB_QPT_RAW_ETHERTYPE to make
the special QP type easier to understand.
cf http://www.mail-archive.com/linux-rdma@vger.kernel.org/msg04530.html
Signed-off-by: Aleksey Senin <alekseys@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (88 commits)
ips driver: make it less chatty
intel_scu_ipc: fix size field for intel_scu_ipc_command
intel_scu_ipc: return -EIO for error condition in busy_loop
intel_scu_ipc: fix data packing of PMIC command on Moorestown
Clean up command packing on MRST.
zero the stack buffer before giving random garbage to the SCU
Fix stack buffer size for IPC writev messages
intel_scu_ipc: Use the new cpu identification function
intel_scu_ipc: tidy up unused bits
Remove indirect read write api support.
intel_scu_ipc: Support Medfield processors
intel_scu_ipc: detect CPU type automatically
x86 plat: limit x86 platform driver menu to X86
acpi ec_sys: Be more cautious about ec write access
acpi ec: Fix possible double io port registration
hp-wmi: acpi_drivers.h is already included through acpi.h two lines below
hp-wmi: Fix mixing up of and/or directive
dell-laptop: make dell_laptop_i8042_filter() static
asus-laptop: fix asus_input_init error path
msi-wmi: make needlessly global symbols static
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
Input: adp5588-keypad - fix NULL dereference in adp5588_gpio_add()
Input: cy8ctmg110 - capacitive touchscreen support
Input: keyboard - also match braille-only keyboards
Input: adp5588-keys - export unused GPIO pins
Input: xpad - add product ID for Hori Fighting Stick EX2
Input: adxl34x - fix leak and use after free
Input: samsung-keypad - Add samsung keypad driver
Input: i8042 - reset keyboard controller wehen resuming from S2R
Input: synaptics - set min/max for finger width
Input: synaptics - only report width on hardware that supports it
Input: evdev - signal that device is writable in evdev_poll()
Input: mousedev - signal that device is writable in mousedev_poll()
Input: change input handlers to use bool when possible
Input: document the MT event slot protocol
Input: introduce MT event slots
Input: usbtouchscreen - implement reset_resume
Input: usbtouchscreen - implement runtime power management
Input: usbtouchscreen - implement basic suspend/resume
Input: Add ATMEL QT602240 touchscreen driver
Input: fix signedness warning in input_set_keycode()
...
* 'v4l_for_2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (243 commits)
V4L/DVB: sms: Convert IR support to use the Remote Controller core
V4L/DVB: sms: properly initialize IR phys and IR name
V4L/DVB: standardize names at rc-dib0700 tables
V4L/DVB: smsusb: enable IR port for Hauppauge WinTV MiniStick
V4L/DVB: dib0700: Fix RC protocol logic to properly handle NEC/NECx and RC-5
V4L/DVB: dib0700: properly implement IR change_protocol
V4L/DVB: dib0700: break keytable into NEC and RC-5 variants
V4L/DVB: dib0700: avoid bad repeat
V4L/DVB: Port dib0700 to rc-core
V4L/DVB: Add a keymap file with dib0700 table
V4L/DVB: dvb-usb: add support for rc-core mode
V4L/DVB: dvb-usb: prepare drivers for using rc-core
V4L/DVB: dvb-usb: get rid of struct dvb_usb_rc_key
V4L/DVB: rj54n1cb0c: fix a comment in the driver
V4L/DVB: V4L2: sh_vou: VOU does support the full PAL resolution too
V4L/DVB: V4L2: sh_mobile_camera_ceu: add support for CSI2
V4L/DVB: V4L2: soc-camera: add a MIPI CSI-2 driver for SH-Mobile platforms
V4L/DVB: V4L2: soc-camera: export soc-camera bus type for notifications
V4L/DVB: V4L2: mediabus: add 12-bit Bayer and YUV420 pixel formats
V4L/DVB: mediabus: fix ambiguous pixel code names
...
Simple changes to fix warnings:
CHECK drivers/infiniband/hw/nes/nes_verbs.c
nes_verbs.c:1944:45: warning: Using plain integer as NULL pointer
nes_verbs.c:1944:48: warning: Using plain integer as NULL pointer
CHECK drivers/infiniband/hw/nes/nes_cm.c
nes_cm.c:2645:43: warning: mixing different enum types
nes_cm.c:2645:43: int enum iw_cm_event_type versus
nes_cm.c:2645:43: int enum iw_cm_event_status
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Acked-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't hang a host thread if the FW stops responding.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
spi_write_then_read() may return its own return codes (e.g. -EIO),
so let's propagate the value down to the probe().
Also, remove jedec == 0 check, it isn't needed as nowadays we use
dedicated SPI device IDs for non-JEDEC flashes.
Suggested-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since commit 18c6182bae ("Rework
probing/JEDEC code"), m25p80 driver successfully registers chips
even if JEDEC probing fails.
This was needed to support non-JEDEC flashes. Though, it appears
that some platforms (e.g. blackfin bf533 stamp[1]) used the old
behavior to detect if there's any flash connected, so the driver
have to fail on JEDEC probing errors.
This patch restores the old behavior for JEDEC flashes, and adds
"-nonjedec" SPI device IDs for M25Pxx flashes, so that the kernel
still supports non-JEDEC flashes.
[1] http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=5975
Reported-by: Mingquan Pan
Reported-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
For no-mmu systems mmap() on RAM/ROM devices already works
but for systems with mmu it probably was not tested and
doesn't work.
This patch allows using mmap() on MTD RAM/ROM devices on systems
with MMU. It has been tested on mpc5121e based platform with
MR0A16A MRAM device attached over LocalBus.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for static flash partitioning from a platform
device. Also, we clean up some weirdness where statements were separated
by commas instead of semicolons. While we are at it, fix some minor bad
white space, too.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The mtd layer is responsible to call mtd->{suspend,resume}. Doing it
again in the driver is wrong and results in a warning:
nand_resume called for a chip which is not in suspended state
at resume time. Removing the calls from the resume and suspend
functions makes them empty allowing them to be deleted completely.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The variable 'syn' was being used uninitialized. Also
fixed incorrect use of syn[] vs s[].
Tested on powerpc board with 64MiB DOC2000.
Signed-off-by: Mark Ware <mware@elphinstone.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Samsung SoCs use own chip_probe function.
Don't touch the memory configuration at probe time.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Samsung SoCs use the own OneNAND controler and detect OneNAND chip at power on.
To use this feature, introduce the chip_probe function.
Also remove workaround for Samsung SoCs.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
EDAC MC3: CE page 0xc32281, offset 0x8a0, grain 0, syndrome 0x1, row 2, channel 1, label "": amd64_edac
EDAC MC3: CE - no information available: amd64_edacError Overflow
Add the missing space before "Error Overflow" on the second line.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Marvell 88ec048 is a derivative of its 88e1121r device. From the programmer's
perspective, the one major difference is the addition of an additional control
bit in Page 2 Register 16 - used to control the padding of odd nibble
preambles.
This patch adds support for this new device, while inheriting as much code as
possible from the existing 88e1121r implementation.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This connector attribute allows you to enable or disable underscan
on a digital output to compensate for panels that automatically
overscan (e.g., many HDMI TVs). Valid values for the attribute are:
off - forces underscan off
on - forces underscan on
auto - enables underscan if an HDMI TV is connected, off otherwise
default value is auto.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Prior to this patch the code was dividing the src_v by the dst_h
and vice versa, rather than src_v/dst_v and src_h/dst_h.
This could lead to problems in the calculation of the display
watermarks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of /ssd/git/drm-next: (230 commits)
drm/i915: Clear the Ironlake dithering flags when the pipe doesn't want it.
drm/agp/i915: trim stolen space to 32M
drm/i915: Unset cursor if out-of-bounds upon mode change (v4)
drm/i915: Unreference object not handle on creation
drm/i915: Attempt to uncouple object after catastrophic failure in unbind
drm/i915: Repeat unbinding during free if interrupted (v6)
drm/i915: Refactor i915_gem_retire_requests()
drm/i915: Warn if we run out of FIFO space for a mode
drm/i915: Round up the watermark entries (v3)
drm/i915: Typo in (unused) register mask for overlay.
drm/i915: Check overlay stride errata for i830 and i845
drm/i915: Validate the mode for eDP by using fixed panel size
drm/i915: Always use the fixed panel timing for eDP
drm/i915: Enable panel fitting for eDP
drm/i915: Add fixed panel mode parsed from EDID for eDP without fixed mode in VBT
drm/i915/sdvo: Set sync polarity based on actual mode
drm/i915/hdmi: Set sync polarity based on actual mode
drm/i915/pch: Set transcoder sync polarity for DP based on actual mode
drm/i915: Initialize LVDS and eDP outputs before anything else
drm/i915/dp: Correctly report eDP in the core connector type
...
Intel variants don't support it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Logic was:
if (mode0 && mode1)
else if (mode0)
else
Should be:
if (mode0 && mode1)
else if (mode0)
else if (mode1)
Otherwise we may end up calculating the priority regs with
unitialized values.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16492
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
I wrote this for the prime sharing work, but I also noticed other external
non-upstream drivers from a large company carrying a similiar patch, so I
may as well ship it in master.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch addresses an issue seen on 82580 in which the MDICNFG
register will be reset during a single function reset and as a
result we will be unable to communicate with the PHY. To correct
the issue, added a call to reset_mdicnfg just prior to the first
access of the MDICNFG register in sgnii_uses_mdio.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC-PHY interconnect register set on ICH/PCH parts is accessed through
a peephole mechanism by writing an offset to a CSR register. The offset
for the interconnect's half-duplex control register (which is used in a
jumbo frame workaround for 82579) is incorrect.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a driver for esd's USB high speed
CAN interface. The driver supports devices with
multiple CAN interfaces.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My fine DisplayPort output was getting ST dithering forever after
having had the LVDS enabled at one point.
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch adds a hwmon driver for package level thermal control. The driver
dumps package level thermal information through sysfs interface so that upper
level application (e.g. lm_sensor) can retrive the information.
Instead of having the package level hwmon code in coretemp, I write a seperate
driver pkgtemp because:
First, package level thermal sensors include not only sensors for each core,
but also sensors for uncore, memory controller or other components in the
package. Logically it will be clear to have a seperate hwmon driver for package
level hwmon to monitor wider range of sensors in a package. Merging package
thermal driver into core thermal driver doesn't make sense and may mislead.
Secondly, merging the two drivers together may cause coding mess. It's easier
to include various package level sensors info if more sensor information is
implemented. Coretemp code needs to consider a lot of legacy machine cases.
Pkgtemp code only considers platform starting from Sandy Bridge.
On a 1Sx4Cx2T Sandy Bridge platform, lm-sensors dumps the pkgtemp and coretemp:
pkgtemp-isa-0000
Adapter: ISA adapter
physical id 0: +33.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0001
Adapter: ISA adapter
Core 1: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0002
Adapter: ISA adapter
Core 2: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0003
Adapter: ISA adapter
Core 3: +32.0°C (high = +79.0°C, crit = +99.0°C)
[ hpa: folded v3 patch removing improper global variable "SHOW" ]
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
LKML-Reference: <1280448826-12004-3-git-send-email-fenghua.yu@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: do not warn unnecessarily
UBI: do not print message about corruptes PEBs if we have none of them
UBI: improve delete-compatible volumes handling
UBI: fix error message and compilation warnings
UBI: generate random image_seq when formatting MTD devices
UBI: improve ECC error message
UBI: improve corrupted flash handling
UBI: introduce eraseblock counter variables
UBI: introduce a new IO return code
UBI: simplify IO error codes
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (291 commits)
ARM: AMBA: Add pclk support to AMBA bus infrastructure
ARM: 6278/2: fix regression in RealView after the introduction of pclk
ARM: 6277/1: mach-shmobile: Allow users to select HZ, default to 128
ARM: 6276/1: mach-shmobile: remove duplicate NR_IRQS_LEGACY
ARM: 6246/1: mmci: support larger MMCIDATALENGTH register
ARM: 6245/1: mmci: enable hardware flow control on Ux500 variants
ARM: 6244/1: mmci: add variant data and default MCICLOCK support
ARM: 6243/1: mmci: pass power_mode to the translate_vdd callback
ARM: 6274/1: add global control registers definition header file for nuc900
mx2_camera: fix type of dma buffer virtual address pointer
mx2_camera: Add soc_camera support for i.MX25/i.MX27
arm/imx/gpio: add spinlock protection
ARM: Add support for the LPC32XX arch
ARM: LPC32XX: Arch config menu supoport and makefiles
ARM: LPC32XX: Phytec 3250 platform support
ARM: LPC32XX: Misc support functions
ARM: LPC32XX: Serial support code
ARM: LPC32XX: System suspend support
ARM: LPC32XX: GPIO, timer, and IRQ drivers
ARM: LPC32XX: Clock driver
...
When transitioning a QP to the error state, in progress RWQEs need to
be marked complete. This also involves releasing the reference count
to the memory regions referenced in the SGEs. The locking in the
receive packet processing wasn't sufficient to prevent qib_error_qp()
from modifying the r_sge state at the same time, thus leading to
kernel panics.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't processes too many packets without allowing other IRQ functions
a chance to run. Otherwise, there is a chance of getting a "soft
lockup" messages and poor application response times.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Up to now, we have set the number of available user contexts based on
the number of hardware contexts which is set according to the number
of available CPUs. This was fine since most CPUs had a power of two
number of cores and the chip supported 4, 8, or 16 user contexts. Now
that some systems have 12 cores, the default isn't optimal and should
be set to 12 even though 16 hardware contexts need to be enabled.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes up a brace warning found by the checkpatch.pl tool
Signed-off-by: Neal Buckendahl <nealb001@tbcnet.com>
Signed-off-by: Dave Jones <davej@redhat.com>
and fix the broken case if a core's frequency depends on others.
trace_power_frequency was only implemented in a rather ungeneric way
in acpi-cpufreq driver's target() function only.
-> Move the call to trace_power_frequency to
cpufreq.c:cpufreq_notify_transition() where CPUFREQ_POSTCHANGE
notifier is triggered.
This will support power frequency tracing by all cpufreq drivers
trace_power_frequency did not trace frequency changes correctly when
the userspace governor was used or when CPU cores' frequency depend
on each other.
-> Moving this into the CPUFREQ_POSTCHANGE notifier and pass the cpu
which gets switched automatically fixes this.
Robert Schoene provided some important fixes on top of my initial
quick shot version which are integrated in this patch:
- Forgot some changes in power_end trace (TP_printk/variable names)
- Variable dummy in power_end must now be cpu_id
- Use static 64 bit variable instead of unsigned int for cpu_id
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: davej@redhat.com
CC: arjan@infradead.org
CC: linux-kernel@vger.kernel.org
CC: robert.schoene@tu-dresden.de
Tested-by: robert.schoene@tu-dresden.de
Signed-off-by: Dave Jones <davej@redhat.com>
For UP systems this is not required, and results in a more consistent
sample interval.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jocelyn Falempe <jocelyn.falempe@motorola.com>
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
lock_policy_rwsem_* and unlock_policy_rwsem_* functions are scheduled
to be unexported when 2.6.33. Now there are no other callers of them
out of cpufreq.c, unexport them and make them static.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Make simpler to read and call.
*** v3 - Always call when powersave_bias is enabled.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Dave Jones <davej@redhat.com>
395913d0b1 ("[CPUFREQ] remove rwsem lock
from CPUFREQ_GOV_STOP call (second call site)") is not needed, because
there is no rwsem lock in cpufreq_ondemand and cpufreq_conservative
anymore. Lock should not be released until the work done.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=1594
Signed-off-by: Andrej Gelenberg <andrej.gelenberg@udo.edu>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Dave Jones <davej@redhat.com>
We don't need a dev_warn when we exceed a thermal or power limit as
we'll handle it appropriately by clamping down on the CPU, GPU or both
as needed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
NR_IRQS may be as low as 16, causing a (harmless?) buffer overflow in
pcmcia_setup_isa_irq():
static u8 pcmcia_used_irq[NR_IRQS];
...
if ((try < 32) && pcmcia_used_irq[irq])
continue;
This is read-only, so if this address would be non-zero, it would just
mean we would not attempt an IRQ >= NR_IRQS -- which would fail anyway!
And as request_irq() fails for an irq >= NR_IRQS, the setting code path:
pcmcia_used_irq[irq]++;
is never reached as well.
Reported-by: Christoph Fritz <chf.fritz@googlemail.com>
CC: stable@kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Fortify the interface to not accept negative values, remove
memctrl_int_store() as a result. Also, sanitize bandwidth setting by
making the argument a simple u32 instead of strange u32 pointer being
passed around for no obvious reason. Then, fix error handling and teach
it to return proper error values. Finally, make code more readable,
simplify debug messages.
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
The correct check is to verify whether in high range we're below 4GB
and not to extract the DctSelBaseAddr again. See "2.8.5 Routing DRAM
Requests" in the F10h BKDG.
Cc: <stable@kernel.org> # .32.x .33.x .34.x
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Switch to reusing the mcheck core's machine check polling mechanism
instead of duplicating functionality by using the EDAC polling routine.
Correct formatting while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
All F2x110-related bit defines are used at only one place so replace
them with simple BIT() macros.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
This option differs from EDAC_DEBUG only by printing the file and
line of where the debug statement is placed, which contains unneeded
information. So remove it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Remove the two syndrome extraction macros and add a single function
which does the same thing but with proper typechecking. While at it,
make sure to cache ECC syndrome size and dump it in debug output.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Size for PMIC read/write command is byte, while it is DWORD for other
IPC commands.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: ALan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Data is 2-byte per entry for PMIC read-modify-update command.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Don't pass more bytes in the command length field than we filled.
Signed-off-by: Andy Ross <andy.ross@windriver.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
some messages take 4 bytes, but only fill 3 bytes....
this patch makes sure that whatever we send to the SCU is zeroed first
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The stack buffer for IPC messages was 16 bytes, limiting messages to a
size of 4 (each message is 32 bit).
However, the touch screen driver is trying to send messages of size 5....
(AC: Set to 20 bytes having checked the max size allowed)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This provides an architecture level board identify function to replace the
cpuid direct usage
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The firmware of production devices does not support this interface so this
is dead code.
Signed-off-by: Sreedhara DS <sreedhara.ds@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Changes to work on bothMmoorestown and Medfield
New pci id added for Medfield
Return type of ipc_data_readl chnaged from u8 to u32
Signed-off-by: Sreedhara DS <sreedhara.ds@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Intel SCU message formats depend upon the processor type. Replace the
module option with automatic detection of the processor type.
Signed-off-by: Sreedhara DS <sreedhara.ds@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
My .config contains ACER_WMI=m. On SPARC. That does not make sense.
Restrict the x86 platform driver menu to x86.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
- Set Kconfig option default n
- Only allow root to read/write io file (sever bug!)
- Introduce write support module param -> default off
- Properly clean up if any debugfs files cannot be created
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: mjg59@srcf.ucam.org
CC: platform-driver-x86@vger.kernel.org
CC: linux-acpi@vger.kernel.org
CC: astarikovskiy@suse.de
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Make dell_laptop_i8042_filter() static as it's used only in dell-laptop.c
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This patch includes below fixes:
1. return -ENOMEM instead of 0 if input_allocate_device fail.
2. fix wrong goto if sparse_keymap_setup fail.
3. fix wrong goto if input_register_device fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
backlight is needlessly defined global.
This patch makes the symbol static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Add support for Toshiba Illumination. This is a set of LEDs installed on
some Toshiba laptops. It is controlled through ACPI, the commands has been
found through reverse engineering. It has been tested on a Toshiba Qosmio
G50-122.
Signed-off-by: Pierre Ducroquet <pinaraf@pinaraf.info>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Moorestown has PMIC chip which contains GPIO blocks. The PMIC chip is
connected to Langwell by SPI interface. So this GPIO driver will be regarded
as SPI GPIO expander though the actual GPIO access is through IPC and SRAM.
The SPI master contoller will probe this device driver by parsing SPIB table.
Cleaned up for new IPC, GPE removed and some printk and other tidying by
Alan Cox. Fixes for points noted by Matthew Garrett
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Formerly these have been exposed through /proc/..
Better register them where all IO ports should get registered
and scream loud if someone else claims to use them.
EC data and command port typically should show up like this
then:
...
0060-0060 : keyboard
0062-0062 : EC data
0064-0064 : keyboard
0066-0066 : EC command
0070-0071 : rtc0
...
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: Alexey Starikovskiy <astarikovskiy@suse.de>
CC: Len Brown <lenb@kernel.org>
CC: linux-kernel@vger.kernel.org
CC: linux-acpi@vger.kernel.org
CC: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: platform-driver-x86@vger.kernel.org
Signed-off-by: Matthew Garrett <mjg@redhat.com>
A userspace app to easily read/write the EC can be found here:
ftp://ftp.suse.com/pub/people/trenn/sources/ec/ec_access.c
Multiple ECs are not supported, but shouldn't be hard to add as soon
as the ec driver itself will support them.
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: Alexey Starikovskiy <astarikovskiy@suse.de>
CC: Len Brown <lenb@kernel.org>
CC: linux-kernel@vger.kernel.org
CC: linux-acpi@vger.kernel.org
CC: platform-driver-x86@vger.kernel.org
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This patch provides the same information through debugfs, which previously was
provided through /proc/acpi/embedded_controller/*/info
This is the gpe the EC is connected to and whether the global lock
gets used.
The io ports used are added to /proc/ioports in another patch.
Beside the fact that /proc/acpi is deprecated for quite some time,
this info is not needed for applications and thus can be moved
to debugfs instead of a public interface like /sys.
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: Alexey Starikovskiy <astarikovskiy@suse.de>
CC: Len Brown <lenb@kernel.org>
CC: linux-kernel@vger.kernel.org
CC: linux-acpi@vger.kernel.org
CC: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: platform-driver-x86@vger.kernel.org
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Other patches in this series add the same info to /sys/... and
/proc/ioports.
The info removed should never have been used in an application,
eventually someone read it manually.
/proc/acpi is deprecated for more than a year anyway...
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: Alexey Starikovskiy <astarikovskiy@suse.de>
CC: Len Brown <lenb@kernel.org>
CC: linux-kernel@vger.kernel.org
CC: linux-acpi@vger.kernel.org
CC: platform-driver-x86@vger.kernel.org
Signed-off-by: Matthew Garrett <mjg@redhat.com>
In current implementation, acpi_pcc_write_sset return 1
if write is successful, 0 if write is failed.
But all the callers consider acpi_pcc_write_sset return 0
if write is successful and return negtive if write is failed.
This patch changes the implementation of acpi_pcc_write_sset to
return 0 if write is successful, -EIO if write is failed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The hotplug_disabled module parameter is determinated at the module load
time. Change the value after the module is loaded does not make sense and
has no effect at all, thus set the permissions to 0444 instead of 0644.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The wapf module parameters defines the behavior of the Fn+Fx wlan key.
The wlan_status and bluetooth_status module parameters are for setting the
wlan/bluetooth status on boot.
All above module parameters are determinated only at the module load time.
Change the value after the module is loaded does not make sense and has
no effect at all, thus set the permissions to 0444 instead of 0644.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Remove non-used acer_quirks struct definition.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
When acpi_evaluate_object() is passed ACPI_ALLOCATE_BUFFER, the caller
must kfree the returned buffer if AE_OK is returned.
Call Trace:
wmab_execute
-> wmi_evaluate_method
-> acpi_evaluate_object
Thus if callers of wmab_execute() pass ACPI_ALLOCATE_BUFFER, the return
buffer must be kfreed if wmab_execute return AE_OK.
[akpm@linux-foundation.org: avoid multiple return points, remove unneeded cast, remove unneeded initialisation of `status']
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
When acpi_evaluate_object() is passed ACPI_ALLOCATE_BUFFER, the caller
must kfree the returned buffer if AE_OK is returned.
The callers of wmi_query_block() pass ACPI_ALLOCATE_BUFFER, and thus must
check its return value before accessing or kfree() on the buffer.
This patch adds a missing kfree(out.pointer) before exit
WMID_set_capabilities() and get_wmid_devices().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
To improve readability rename add_device() to
create_toshiba_proc_entries() and rename remove_device() to
remove_toshiba_proc_entries().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Márton Németh <nm127@freemail.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Add error checking and return -ENOMEM if input_allocate_device() fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
remove_device() and add_device() are not related to ACPI APIs, it does not
make sense to return acpi_status for both functions.
Current implementation of add_device() always AE_OK, thus the return value
checking for add_device() always return false for ACPI_FAILURE(status).
This patch makes add_device() to be void and remove the unnecessary return
value checking.
remove_proc_entry() won't fail, thus change remove_device() to be void.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Márton Németh <nm127@freemail.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Fix resource reclaim in below cases:
1. acerhdf_register_platform() does not properly handle
platform_device_alloc() failure and platform_device_add() failure This
patch adds error handing for acerhdf_register_platform().
2. acerhdf_register_platform() return err with acerhdf_dev == NULL.
as a result, acerhdf_unregister_platform() does not do resource reclaim
in acerhdf_init() error path. This patch adds error handing for
acerhdf_register_platform(), thus correct the error handing path in
acerhdf_init(). goto out_err instead of err_unreg if
acerhdf_register_platform() fail.
3. platform_device_del() should only used in error handling. Current
implementation missed a platform_device_put() in acerhdf_exit. This
patch fixes it by using platform_device_unregister() instead of
platform_device_del() in acerhdf_unregister_platform.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Feuerer <peter@piie.net>
Cc: Matthew Garrett <mjg@redhat.com>
Acked-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
In current implementation, store_ledd() does not return error if
write_acpi_int fail. This patch fixes it by return -ENODEV if
write_acpi_int fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
According to the comments of write_acpi_int_ret(), write_acpi_int_ret()
should return 0 if write is successful, -1 else. Thus if handle is NULL,
the write does not happen, it should return -1.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
rfkill uses a const struct rfkill_ops pointer.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The following symbols are needlessly defined global:
logolamp_led
kblamps_led
This patch makes the symbols static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
cmpc_accel_sensitivity_attr is needlessly defined global.
This patch makes the symbol static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Daniel Oliveira Nascimento <don@syst.com.br>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The following symbols are needlessly defined global:
thz_dev
cl_dev
acerhdf_dev
acerhdf_dev_ops
acerhdf_cooling_ops
This patch makes the symbols static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Borislav Petkov <bp@alien8.de>
Acked-by: Peter Feuerer <peter@piie.net>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
In the case of no match ( hotk->model == END_MODEL ), the only posible
case to return 0 is to have a Samsung P30 detected. This patch improves
readability by moving related code after if/else clause to be inside if
clause.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Karol Kozimor <sziwan@users.sourceforge.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
In the case of no match ( hotk->model == END_MODEL ), model sholud be
kfreed before return AE_OK.
This patch includes below fixes:
1. adds a missing kfree(model) before return AE_OK.
2. asus_hotk_get_info should return int, thus return 0 instead of AE_OK.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Karol Kozimor <sziwan@users.sourceforge.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
dmi_check_system() walks the table running matching functions until
someone returns non zero or we hit the end.
This patch makes dmi_check_cb to return 1 so dmi_check_system() return
immediately when a match is found.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Cc: Matthew Garrett <mjg@redhat.com>a
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The driver now supports the Compal JHL90 (which I use) and it has some
added features. The biggest novelties are a battery interface
(power_supply) and a temperature and fan control interface (hmwon). It
also adds a power-off feature to the backlight subsystem and it exports a
few files that can enable/disable wake_on_XXX events.
Much of the original code of the old features is still there, but I've
changed some names to keep the naming more coherent with the added
functionalities. (Sorry for the huge patch)
Some technical stuff about the new driver:
First of all, I'm not sure if the extra features also work on the other
Compal boards. Currently they only get enabled if the DMI data indicates
you are on a JHL90 board.
Secondly, I've noticed a quirk in my fan controller. I have to re-send
the wanted pwm-level to the controller every so often. If I don't do
this, the fanspeed will slowly rise until after a couple of minutes it's
at full speed. (Note that every normal userland application will probably
update the pwm-level every so often anyway, based on temperature readings,
so this might not be an issue in practice) If this turns out to be a
problem with all the controllers, maybe we should implement a kernel timer
and have the driver re-send the pwm level every XX seconds to make this
transparent to userspace? (However, I couldn't immediately find a way to
do this cleanly.)
Additional information can be found in the source comments.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: add missing semicolon]
Signed-off-by: Roald Frederickx <roald.frederickx@gmail.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
compal-laptop uses hwmon interfaces, so it should depend on HWMON.
compal-laptop.c:(.devinit.text+0x4071f): undefined reference to `hwmon_device_register'
compal-laptop.c:(.devexit.text+0x6ec0): undefined reference to `hwmon_device_unregister'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Roald Frederickx <roald.frederickx@gmail.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
input_free_device() should only be used if input_register_device() was not
called yet or if it failed. This patch removes unnecessary
input_free_device calls.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Matthew Garrett <mjg@redhat.com>a
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Peter Feuerer <peter@piie.net>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Andreas Mohr <andi@lisas.de>
Cc: Len Brown <lenb@kernel.org>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Driver didn't verify the pointers in which it got product information back
from DMI; on QEMU one of the pointers came back null, which made the
driver crash and subsequently caused a kernel panic.
Signed-off-by: Rahul Chaturvedi <rkc@chromium.org>
Signed-off-by: Peter Feuerer <peter@piie.net>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Andreas Mohr <andi@lisas.de>
Cc: Len Brown <lenb@kernel.org>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Remove "chk_off" as it was only needed for T31 netbooks. But those
netbooks can also be handled just with "cmd_off" register (0x9e) for
reading the state back.
Signed-off-by: Peter Feuerer <peter@piie.net>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Andreas Mohr <andi@lisas.de>
Cc: Len Brown <lenb@kernel.org>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Add new BIOS versions for Acer 1410 and 1810xx and Packard Bell netbooks.
Fixed registers of Acer AOA150 BIOS version v0.3114: Old registers caused
Fan to spin up at every temperature check.
Signed-off-by: Peter Feuerer <peter@piie.net>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Andreas Mohr <andi@lisas.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Thomas Bächler reports that his machine generates two keycodes for zooming
in and out. Add these to the default keymap.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Thomas Bächler <thomas@archlinux.org>
platform_device_unregister calls platform_device_del and platform_device_put,
thus this change is logically equivalent to original code.
I made this change because the documents in platform.c shows that:
platform_device_del and platform_device_put must _only_ be externally called
in error cases. All other usage is a bug.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
If dell_new_hk_type is true, dell_legacy_wmi_keymap will point to a memory
allocated in setup_new_hk_map().
In this case, the memory is not freed in current implementation.
This patch fixes the leak by kfree(dell_wmi_keymap) if dell_new_hk_type is true.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
dmi_check_system() walks the table running matching functions until someone
returns non zero or we hit the end.
This patch makes dmi_matched to return 1 so dmi_check_system() return
immediately when a match is found.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The interface file is not writable, thus set permissions to S_IRUGO.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The callers of write_acpi_int_ret() pass ACPI_ALLOCATE_BUFFER,
the caller must kfree the returned buffer if AE_OK is returned.
This patch adds a missing kfree(buffer.pointer) before return -ENOMEM
if kstrdup fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
When acpi_evaluate_object() is passed ACPI_ALLOCATE_BUFFER,
the caller must kfree the returned buffer if AE_OK is returned.
The callers of wmi_get_event_data() pass ACPI_ALLOCATE_BUFFER,
and thus must check its return value before accessing
or kfree() on the buffer.
This patch adds return value checking for wmi_get_event_data()
and adds a missing kfree(obj) in the end of wmi_notify_debug
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Fixes pressing the eject key on Dell Studio 1555 does not work and produces
message :
dell-wmi: Unknown key 0 pressed
Signed-off-by: Islam Amer <pharon@gmail.com>
platform_device_unregister will also call platform_device_put() to drop reference count.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This patch properly kfree out.pointer and gblock in error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This patch fixes the resource reclaim in acer_wmi_init error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Stanse found that there are two NULL checks missing in ips_monitor. So
check their value too and bail out appropriately if the allocation
failed.
While at it, add one more kfree to the fail path. It is not necessary
now, but may be needed in the future when a new allocation is added.
And for completeness.
Also remove unneeded initialization of the variables. They are all set
right after their declaration.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current implementation in hp_wmi_init does not check any error and always
return success.
This patch properly handles recource reclaim and return err in error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
rfkill_alloc returns NULL when it fails if RFKILL is enabled. When RFKILL is
disabled, its return value of ERR_PTR(-ENODEV) is OK to use as all rfkill
functions will work with it, as they are simply empty stubs.
Reported-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: platform-driver-x86@vger.kernel.org
Cc: mjg@redhat.com
Cc: don@syst.com.br
Cc: rpurdie@rpsys.net
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Be sure to enable GPU turbo by default at load time and check GPU busy
and MCP exceeded status correctly. Also fix up CPU power comparison and
work around buggy MCH temp reporting.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Intel Core i3/5 platforms with integrated graphics support both CPU and
GPU turbo mode. CPU turbo mode is opportunistic: the CPU will use any
available power to increase core frequencies if thermal headroom is
available. The GPU side is more manual however; the graphics driver
must monitor GPU power and temperature and coordinate with a core
thermal driver to take advantage of available thermal and power headroom
in the package.
The intelligent power sharing (IPS) driver is intended to coordinate
this activity by monitoring MCP (multi-chip package) temperature and
power, allowing the CPU and/or GPU to increase their power consumption,
and thus performance, when possible. The goal is to maximize
performance within a given platform's TDP (thermal design point).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
msi-laptop uses i8042_*() interfaces, so it should depend on
SERIO_I8042. E.g., when SERIO_I8042=m and MSI_LAPTOP=y:
msi-laptop.c:(.text+0x18a7fe): undefined reference to `i8042_install_filter'
msi-laptop.c:(.init.text+0xd69d): undefined reference to `i8042_remove_filter'
msi-laptop.c:(.exit.text+0x19c3): undefined reference to `i8042_remove_filter'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Randy Dunlap has reported that building classmate-laptop fails when
CONFIG_RFKILL=m and CONFIG_ACPI_CMPC=y. He suggested depending on
RFKILL, but, then, it will not be possible to select classmate-laptop
when RFKILL is off. There's no known problem with building and using
classmate-laptop with RFKILL off. So depend on RFKILL or RFKILL=n.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: platform-driver-x86@vger.kernel.org
Cc: Daniel Oliveira Nascimento <don@syst.com.br>
Give different error messages if device_enum is NULL or if its type field
has the wrong value.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@
if ((E == NULL && ...) || ...)
{
... when != if (...) S1 else S2
when != E = E1
* E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
- Improve error handling, by explictly return zero for success, error otherwise
- WMI query command can have arbitrary input sized params
- WMI query command can have specific output sized params (0, 4, 128,..) byte
I like to go on here, but this is a rather intrusive change that should
be looked at first. I am sure the one or other thing can be done better or
there might be typo/bug somewhere.
This did not get any testing yet, only compile tested.
Next steps could be:
- Eventually introduce hp_wmi_perform_{read,write}_query macros
- Introduce new wireless query interface (0x1B)
- more
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
CC: linux-acpi@vger.kernel.org
CC: platform-driver-x86@vger.kernel.org
Depending on ACPI version (1.0 -> 32 bit) an integer could be
32 or 64 bit long. _WED internal concatenates two integers and
the return value will be 8 byte (2* 32 bit) or 16 byte (2* 64 bit)
long, depending on the ACPI version.
Also the data send with the WMI event is defined to be splitted into:
- Event ID -> 4 bytes
- Event Data -> 4 bytes
This gets messed up with new ACPI versions.
But it's a HP BIOS bug that may get fixed in the future
-> Support both, 16 and 8 byte _WED buffers.
Also the wrong assumption that from the event data sent, only the
first byte is relevant got cleaned up that it fits event_id/event_data
as described above.
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: robert.moore@intel.com
Signed-off-by: Matthew Garrett <mjg@redhat.com>
CC: platform-driver-x86@vger.kernel.org
CC: linux-acpi@vger.kernel.org
Event id 0x4 defines the hotkey event.
No need (or even wrong) to query HPWMI_HOTKEY_QUERY if event id is != 0x4.
Reorder the eventcode conditionals and use switch case instead of if/else.
Use an enum for the event ids cases.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
CC: linux-acpi@vger.kernel.org
CC: platform-driver-x86@vger.kernel.org
This patch includes below fixes in error path:
1. fix a memory leak if device_create_file failed in
intel_menlow_add_one_attribute
2. properly free added attributes before return error in
intel_menlow_register_sensor error handler
3. properly call acpi_bus_unregister_driver before return error in
intel_menlow_module_init
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Prepare for supporting panels other than Taal in this driver.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add support for configuring regulators in the panel specific
configuration data.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The driver will support other panels in addition to Taal, print also the
name.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add a structure for panel specific configration to be able to support
more than one panel in the future.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Make ESD check usage configurable in DSI panel data, as opposed to a
define.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Get board specific information from the Nokia DSI panel data structure
instead of the DSS.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add gpio irq based external TE support with timeout.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Switch from numbered to named labels to make it easier to add new
labels for error handling.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move ESD work queuing and cancelling out of taal_power_on/off() to avoid
problems related to taal_esd_work() calling the power on/off functions.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Change state only if power on was succesful.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move dsi_bus_lock/unlock() out of taal_power_on/off() to avoid deadlock
in taal_esd_work().
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Bail out from taal_enable_te() and taal_run_test() if panel is not
enabled.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Check return values and bail out on errors.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
ESD work is never queued in probe, no need to cancel it on probe error.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Separate gpio_request() and request_irq() error handling.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
After the addition of proper hardware reset, taal_hw_reset(), there's no
need for an additional platform enable/disable. Remove them.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Avoid potential race conditions in sysfs access to taal data.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Issue a proper reset pulse on the reset line instead of just doing power
on/off.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
taal_bl_update_status was missing locks to protect taal_data. This caused
a kernel crash randomly, as the code attempted to set the brightness while
the OMAP's DSI block was actually disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Using nanoseconds as arguments to functions that set the DSI timeouts was
perhaps not so good idea. The timeouts are based on different DSI clocks,
so the possible range for the timeouts vary greatly depending on the
clocks. Also, the multipliers used with the timeouts cause big gaps in the
timeout range, meaning that the nanosecond based functions could cause the
timeout to be quite far from the intended value.
This patch changes the functions to take the plain tick values with the
multiplier enable/disable bits, and sets the TA/LP_RX/HS_TX timeouts to
maximum. While the timeouts could be much lower, the fact is that when
TA/LP_RX/HS_TX timeout happens, we are in an error situation and not in a
hurry anyway.
STOP_STATE_COUNTER is a different matter, but it is only used at
initialization time, and won't normally affect the performance.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Using the shared workqueue led to to a deadlock in the case where the
display was unblanked via keyboard.
What happens is something like this:
- User presses a key
context 1:
- drivers/char/keyboard.c calls schedule_console_callback()
- fb_unblank takes the console semaphore
- dsi bus lock is taken, and frame transfer is started (dsi bus lock is
left on)
- Unblank code tries to set the panel backlight, which tries to take dsi
bus lock, but is blocked while the frame transfer is going on
context 2, shared workqueue, console_callback in drivers/char/vt.c:
- Tries to take console semaphore
- Blocks, as console semaphore is being held by context 1
- No other shared workqueue work can be run
context 3, HW irq, caused by FRAMEDONE interrupt:
- Interrupt handler schedules framedone-work in shared workqueue
- Framedone-work is never ran, as the shared workqueue is blocked. This
means that the unblank thread stays blocked, which means that context 2
stays blocked.
While I think the real problem is in keyboard/virtual terminal code, using
a private workqueue in the DSI driver is perhaps safer and more robust
than using the shared one. The DSI works should not be delayed more than a
millisecond or so, and even if the private workqueue gives us no hard
promise of doing so, it's still safer bet than the shared workqueue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
dsi_vc_flush_receive_data() is meant to dump data when something has gone
wrong, and thus we should use DSSERR, not DSSDBG.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Trigger WARN_ON() messages from various places in the code in case the
memory region is not currently locked.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When more than one memory region needs to be lockd at the same time use
the memory region id to fix the order in which the locks are taken. Also
one needs to use the _nested() versions of the locking primitives. The
memory region id can serve as the lock class there as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
R/W semaphore is a good fit for the memory region locking pattern.
So use it.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add locking to the memory regions to make sure the memory region size
won't be changed while some other piece of code is performing some
checks or setup based on that information.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Separate the memory region from the framebuffer device a little bit.
It's now possible to select the memory region used by the framebuffer
device using the new mem_idx parameter of omapfb_plane_info. If the
mem_idx is specified it will be interpreted as an index into the
memory regions array, if it's not specified the framebuffer's index is
used instead. So by default each framebuffer keeps using it's own
memory region which preserves backwards compatibility.
This allows cloning the same memory region to several overlays and yet
each overlay can be controlled independently since they can be
associated with separate framebuffer devices.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
In omapfb_enable_overlay() if the overlay state is already what we want
skip the set_overlay_info().
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
If video memory hasn't been allocate have check_fb_var() still check
most of the settings, just skip the ones involving the size of the
memory region. Also skip the memory address calculations in
omapfb_setup_overlay() if there's no memory.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Split the overlay address calculations into their own function.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When there are multiple scaled overlays simply checking whether the update
area intersects any of them in order is not enough. If eg. VID1 starts out
completely outside the update area but VID2 causes the update area to
increase in such a way that VID1 now falls partially within the increased
update area VID1 should be rechecked and the update area possibly
increased even further to fully encompass VID1. So simply keep looping
over the overlays until such time that none of the overlays caused the
update area to change.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When DSS transitions from off mode to on VENC may generate a spurious
SYNC_LOST_DIGIT error. Just ack it when restoring the context. Also
restore IRQENABLE last to avoid triggering interrupts before the
context is fully restored.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When the display is not active make the wait_for_go() functions return
immediately.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Check whether the display actually has the set_update_mode() function
before calling it. Only the sysfs codepath was broken, the omapfb ioctl
had the necessary protection.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
For some reason screen updates of certain odd widths seem to be triggering
HS TX timeouts on OMAP 3430, even if bigger updates do not. The reason for
this is unknown, but increasing the timeout removes the problem with no
(so far) noticeable problems. I haven't seen this problem on OMAP 3630.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Several drivers contained dummy code to request for memory windows,
even though they never made use of it. Remove all such code
snippets.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Insert PCMCIA device resources into the resource tree. However, this is
currently only implemented for sockets which do not statically map the
resources.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Introduce a new field into struct pcmcia_device named "resource" and of
type struct resource *, which contains the IO port ranges allocated for
this device. Memory window ranges and registration with the resource
trees will follow at a later date.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch adds support for RGMII RX/TX delay configuration on marvell 88e1121
and derivatives. With this patch, PHY_INTERFACE_MODE_RGMII_*ID modes are now
supported on these devices.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The typo was causing compilation errors since "dev" was not defined.
Signed-off-by: Henrique Camargo <henrique.camargo@ensitec.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize all IRQs when using MSI-X. Similar to ixgbe.
Issue was reported on e1000e, but the patch is also valid for igb.
CC: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change corrects an issue that resulted in a null pointer dereference
for the addition of VLAN 0 without any VLANs being registered. Also this
code removes some unnecessary checks for defines and the unnecessary setting
of VLAN flags since that is now handled within the kernel via the
vlan_features.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original patch/work from Jean Delvare <jdelvare@suse.de>
Synchronize all IRQs when in MSI-X IRQ mode.
Jean's original patch hard coded the sync with the 3 possible vectors,
this patch incorporates more flexibility for the future and aligns
with how igb stores the number of vectors into the adapter structure.
CC: Jean Delvare <jdelvare@suse.de>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pm_qos_add_request call has to register the pm_qos request with the pm_qos
susbsystem before first use of the pm_qos request via
pm_qos_update_request.
As pm_qos changed to use plists there is no benefit in registering and
unregistering the pm_qos request on ifup/ifdown and thus we move the
registering into e1000_open and the unregistering in e1000_close.
This fixes the following warning:
[ 1.786060] WARNING: at kernel/pm_qos_params.c:264
pm_qos_update_request+0x28/0x54()
[ 1.786088] Hardware name: Latitude E6500
[ 1.787045] pm_qos_update_request() called for unknown object
[ 1.787966] Modules linked in:
[ 1.788940] Pid: 1, comm: swapper Not tainted 2.6.35-rc5-mmotm0719 #1
[ 1.790035] Call Trace:
[ 1.791121] [<ffffffff81037335>] warn_slowpath_common+0x80/0x98
[ 1.792205] [<ffffffff810373e1>] warn_slowpath_fmt+0x41/0x43
[ 1.793279] [<ffffffff81057c14>] pm_qos_update_request+0x28/0x54
[ 1.794347] [<ffffffff8134889e>] e1000_configure+0x421/0x459
[ 1.795393] [<ffffffff8134afbd>] e1000_open+0xbd/0x37c
[ 1.796436] [<ffffffff8105743a>] ? raw_notifier_call_chain+0xf/0x11
[ 1.797491] [<ffffffff8145f948>] __dev_open+0xae/0xe2
[ 1.798547] [<ffffffff8145f997>] dev_open+0x1b/0x49
[ 1.799612] [<ffffffff8146e36e>] netpoll_setup+0x84/0x259
[ 1.800685] [<ffffffff81b5037c>] init_netconsole+0xbc/0x21f
[ 1.801744] [<ffffffff81b5026c>] ? sir_wq_init+0x0/0x35
[ 1.802793] [<ffffffff81b502c0>] ? init_netconsole+0x0/0x21f
[ 1.803845] [<ffffffff810002ff>] do_one_initcall+0x7a/0x12f
[ 1.804885] [<ffffffff81b2ccae>] kernel_init+0x138/0x1c2
[ 1.805915] [<ffffffff81003554>] kernel_thread_helper+0x4/0x10
[ 1.806937] [<ffffffff81590e00>] ? restore_args+0x0/0x30
[ 1.807955] [<ffffffff81b2cb76>] ? kernel_init+0x0/0x1c2
[ 1.808958] [<ffffffff81003550>] ? kernel_thread_helper+0x0/0x10
[ 1.809958] ---[ end trace 84b562a00a60539e ]---
Signed-off-by: Florian Mickler <florian@mickler.org>
Tested-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Endpoint timer manipulation needs to be done inside the lock. Otherwise
we can get into a situation where a timer is stopped before it is started,
which hits the WARN_ON() in stop_ep_timer().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is only one control txq per tx channel. So use the port number
as the queue index when sending.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There exists a race condition where the app disconnects, which
initiates an orderly close (via rdma_fini()), concurrently with an
ingress abort condition, which initiates an abortive close operation.
Since rdma_fini() must be called without IRQs disabled, the fini can
be called after the QP has been transitioned to ERROR. This is ok,
but we need to protect against qp->ep getting NULLed.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The kpad structure is assigned to i2c client via i2s_set_clientdata()
at the end of adp5588_probe(), but in adp5588_gpio_add() we tried to
access it (via dev_get_drvdata! which is not nice at all) causing an
oops.
Let's pass pointer to kpad directly into adp5588_gpio_add() and
adp5588_gpio_remove() to avoid accessing driver data before it is
set up.
Also split out building of gpiomap into a separate function to
clear the logic.
Reported-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Removed TODO item 2 :
Current UIM/KIM communicate via the rfkill device and identified by the unique idx
assisgned by the rfkill sub-system to each of these rfkill entries.
Removed TODO item 1 :
Since there is no way we can test existance of multiple connectivity
devices on platform.
However the basic infrastructure as in providing a context to ST driver
exist.
If multiple devices have to exist on a given platform, multiple ST
platform devices need to be registered and each of the protocol drivers
have to mention which platform device they want to bind to/make use of.
Removed TODO item 3:
Locking have been reviewed and commit
36b5aee46b documents locking.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a common name format for PCI_VENDOR/DEVICE_ID constants.
wlags49_h2 names doesn't fit in the standard.
This patch change the names and also fix some style issues.
Thanks a lot,
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the wwrap.c file that fixes up a brace warnings and
other errors found by the checkpatch.pl tool.
Signed-off-by: Daniele Boncompagni <daniele.boncompagni@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In today linux-next I got a compilation warning:
drivers/staging/quatech_usb2/quatech_usb2.c:1852: warning:
‘qt2_box_flush’ defined but not used
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
rtl8192_usb_probe() does not check alloc_ieee80211() and
register_netdev() return values for errors.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
