For i.MX6SX enet use AXI bus, reset MAC will make system bus dead
if ENET-AXI bus has pending access (AHB bus should not have such issue).
So, disable enet with AVB MAC instead of reset MAC itself.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
initilized all queues according to queue number get from DT file.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Duan Fugang <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the tx/rx queue number is 1, user can config the queue number
at DTS file like this:
fsl,num-tx-queues=<3>;
fsl,num-rx-queues=<3>
Since i.MX6SX enet-AVB IP support multi queues, so use multi queues
interface to allocate and set up an Ethernet device.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just change data structure to support multi-queue.
Only 1 queue enabled.
Ethernet multiqueue mechanism can improve performance in SMP system.
For single hw queue, multiqueue can balance cpu loading.
For multi hw queues, multiple cores can process network packets in parallel,
and refer the article for the detail advantage for multiqueue:
http://vger.kernel.org/~davem/davem_nyc09.pdf
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add enet AVB feature macro define for imx6sx.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6sx enet has below clocks for user config:
clk_ipg: ipg_clk_s, ipg_clk_mac0_s, 66Mhz
clk_ahb: enet system clock, it is enet AXI clock for imx6sx.
For imx6sx, it alos is the clock source of interrupt coalescing.
The clock range: 200Mhz ~ 266Mhz.
clk_ref: refrence clock for tx and rx. For imx6sx enet RGMII mode,
the refrence clock is 125Mhz coming from internal PLL or external.
In i.MX6sx-arm2 board, the clock is from internal PLL.
clk_ref is optional, depends on board.
clk_enet_out: The clock can be output from internal PLL. It can supply 50Mhz
clock for phy. clk_enet_out is optional, depends on chip and board.
clk_ptp: 1588 ts clock. It is optional, depends on chip.
The patch add clk_ref to distiguish the different clocks.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the Marvell driver with some cleanups by Claudio Leite
and myself.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Claudio Leite <leitec@staticky.com>
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla says:
====================
be2net: patch set
Patch 1 fixes some minor issues with log messages in be2net.
Patch 2 replaces strcpy() calls with strlcpy() to avoid possible buffer
overflow.
Patch 3 improves the RX buffer posting scheme for jumbo frames.
Patch 4 replaces the use of v0 of SET_FLOW_CONTROL cmd with v1 to receive
a definitive completion status from FW.
Patch 5 adds support for ethtool "-m" ethtool option.
Patch 6 fixes port-type reporting via ethtool get_settings for QSFP/SFP+
interfaces.
Patch 7 fixes the usage of MODIFY_EQD FW cmd to target a max of 8 EQs on
Lancer chip.
Patch 8 enables PCIe error reporting even for VFs.
Pls consider applying this patch set to net-next. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently PCIe error reporting is enabled only on PFs. This patch enables
this feature on VFs too as Lancer VFs support it.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MODIFY_EQ_DELAY FW cmd on Lancer is supported for a max of 8 EQs per cmd.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the ethtool port-type/supported/advertising values based on the
cable_type for QSFP and SFP+ interfaces. The cable_type is parsed from
the transceiver data fetched from the FW.
Signed-off-by: Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the dump-module-eeprom and module-info
ethtool options.
Signed-off-by: Mark Leonard <mark.leonard@emulex.com>
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some configurations the FW doesn't allow changing flow control settings
of a link. Unless a v1 version of the SET_FLOW_CONTROL cmd is used, the FW
doesn't report an error to the driver.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the RX path, the driver currently consumes upto 64 (budget) packets in
one NAPI sweep. When the size of the packet received is larger than a
fragment size (2K), more than one fragment is consumed for each packet.
As the driver currently posts a max of 64 fragments, all the consumed
fragments may not be replenished. This can cause avoidable drops in RX path.
This patch fixes this by posting a max(consumed_frags, 64) frags. This is
done only when there are atleast 64 free slots in the RXQ.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace strcpy with strlcpy, as it avoids a possible buffer overflow.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following minor issues with log messages in be2net:
1) Period is not required at the end of log message.
2) Remove "Unknown grp5 event" logs to reduce noise. The driver can safely
ignore async events from FW it's not interested in.
3) Reword a log message for better readability to say that SRIOV
"is disabled" rather than "not supported".
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have 2 pkt_type_offset functions doing the same thing and
spread across the architecture files. Remove those and replace them
with a PKT_TYPE_OFFSET macro helper which gets the constant value from a
zero sized sk_buff member right in front of the bitfield with offsetof.
This new offset marker does not change size of struct sk_buff.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we introduced an additional multiplexing/demultiplexing layer
with commit 3e8a72d1da ("net: dsa: reduce number of protocol hooks")
that lives within the DSA code, we no longer need to have a given switch
driver tag_protocol be an actual ethertype value, instead, we can
replace it with an enum: dsa_tag_protocol.
Do this replacement in the drivers, which allows us to get rid of the
cpu_to_be16()/htons() dance, and remove ETH_P_BRCMTAG since we do not
need it anymore.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support hw VLAN for tx and rx. And enable them by default.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap_resource() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
If IPv6 is explicitly disabled before the interface comes up,
it makes no sense to continue when it comes up, even just
print a message.
(I am not sure about other cases though, so I prefer not to touch)
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang says:
====================
ipv6: clean up locking code in anycast and mcast
This patchset cleans up the locking code in anycast.c and mcast.c
and makes the refcount code more readable.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
v1 -> v2:
* refactor some code and make it in a separated patch
* update comments
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor out allocation and initialization and make
the refcount code more readable.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly the code is already protected by rtnl lock.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly the code is already protected by rtnl lock.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor out allocation and initialization and make
the refcount code more readable.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it accept inet6_dev, and rename it to __ipv6_dev_ac_inc()
to reflect this change.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just move rtnl lock up, so that the anycast list can be protected
by rtnl lock now.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These code is now protected by rtnl lock, rcu read lock
is useless now.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov says:
====================
bonding: get rid of curr_slave_lock
This is the second patch-set dealing with bond locking and the purpose here
is to convert curr_slave_lock into a spinlock called "mode_lock" which can
be used in the various modes for their specific needs. The first three
patches cleanup the use of curr_slave_lock and prepare it for the
conversion which is done in patch 4 and then the modes that were using
their own locks are converted to use the new "mode_lock" giving us the
opportunity to remove their locks.
This patch-set has been tested in each mode by running enslave/release of
slaves in parallel with traffic transmission and miimon=1 i.e. running
all the time. In fact this lead to the discovery of a subtle bug related to
RCU which will be fixed in -net.
Also did an allmodconfig test just in case :-)
v2: fix bond_3ad_state_machine_handler's use of mode_lock and
curr_slave_lock
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that locks have been removed, remove some unnecessary comments and
adjust others to reflect reality. Also add a comment to "mode_lock" to
describe its current users and give a brief summary why they need it.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have bond->mode_lock, we can remove the state_machine_lock
and use it in its place. There're no fast paths requiring the per-port
spinlocks so it should be okay to consolidate them into mode_lock.
Also move it inside the unbinding function as we don't want to expose
mode_lock outside of the specific modes.
Suggested-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ALB/TLB specific spinlocks are no longer necessary as we now have
bond->mode_lock for this purpose, so convert them and remove them from
struct alb_bond_info.
Also remove the unneeded lock/unlock functions and use spin_lock/unlock
directly.
Suggested-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
curr_slave_lock is now a misleading name, a much better name is
mode_lock as it'll be used for each mode's purposes and it's no longer
necessary to use a rwlock, a simple spinlock is enough.
Suggested-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly all users of curr_slave_lock already have RTNL as we've discussed
previously so there's no point in using it, the one case where the lock
must stay is the 3ad code, in fact it's the only one.
It's okay to remove it from bond_do_fail_over_mac() as it's called with
RTNL and drops the curr_slave_lock anyway.
bond_change_active_slave() is one of the main places where
curr_slave_lock was used, it's okay to remove it as all callers use RTNL
these days before calling it, that's why we move the ASSERT_RTNL() in
the beginning to catch any potential offenders to this rule.
The RTNL argument actually applies to all of the places where
curr_slave_lock has been removed from in this patch.
Also remove the unnecessary bond_deref_active_protected() macro and use
rtnl_dereference() instead.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First in rlb_teach_disabled_mac_on_primary() it's okay to remove
curr_slave_lock as all callers except bond_alb_monitor() already hold
RTNL, and in case bond_alb_monitor() is executing we can at most have a
period with bad throughput (very unlikely though).
In bond_alb_monitor() it's okay to remove the read_lock as the slave
list is walked with RCU and the worst that could happen is another
transmitter at the same time and thus for a period which currently is 10
seconds (bond_alb.h: BOND_ALB_LP_TICKS).
And bond_alb_handle_active_change() is okay because it's always called
with RTNL. Removed the ASSERT_RTNL() because it'll be inserted in the
parent function in a following patch.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the read_lock in bond_3ad_lacpdu_recv() since when the slave is
being released its rx_handler is removed before 3ad unbind, so even if
packets arrive, they won't see the slave in an inconsistent state.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtqueue_add() populates the virtqueue descriptor table from the sgs
given. If it uses an indirect descriptor table, then it puts a single
descriptor in the descriptor table pointing to the kmalloc'ed indirect
table where the sg is populated.
Previously vring_add_indirect() did the allocation and the simple
linear layout. We replace that with alloc_indirect() which allocates
the indirect table then chains it like the normal descriptor table so
we can reuse the core logic.
This slows down pktgen by less than 1/2 a percent (which uses direct
descriptors), as well as vring_bench, but it's far neater.
vring_bench before:
1061485790-1104800648(1.08254e+09+/-6.6e+06)ns
vring_bench after:
1125610268-1183528965(1.14172e+09+/-8e+06)ns
pktgen before:
787781-796334(793165+/-2.4e+03)pps 365-369(367.5+/-1.2)Mb/sec (365530384-369498976(3.68028e+08+/-1.1e+06)bps) errors: 0
pktgen after:
779988-790404(786391+/-2.5e+03)pps 361-366(364.35+/-1.3)Mb/sec (361914432-366747456(3.64885e+08+/-1.2e+06)bps) errors: 0
Now, if we make force indirect descriptors by turning off any_header_sg
in virtio_net.c:
pktgen before:
713773-721062(718374+/-2.1e+03)pps 331-334(332.95+/-0.92)Mb/sec (331190672-334572768(3.33325e+08+/-9.6e+05)bps) errors: 0
pktgen after:
710542-719195(714898+/-2.4e+03)pps 329-333(331.15+/-1.1)Mb/sec (329691488-333706480(3.31713e+08+/-1.1e+06)bps) errors: 0
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to have several callers which just used arrays. They're
gone, so we can use sg_next() everywhere, simplifying the code.
On my laptop, this slowed down vring_bench by 15%:
vring_bench before:
936153354-967745359(9.44739e+08+/-6.1e+06)ns
vring_bench after:
1061485790-1104800648(1.08254e+09+/-6.6e+06)ns
However, a more realistic test using pktgen on a AMD FX(tm)-8320 saw
a few percent improvement:
pktgen before:
767390-792966(785159+/-6.5e+03)pps 356-367(363.75+/-2.9)Mb/sec (356068960-367936224(3.64314e+08+/-3e+06)bps) errors: 0
pktgen after:
787781-796334(793165+/-2.4e+03)pps 365-369(367.5+/-1.2)Mb/sec (365530384-369498976(3.68028e+08+/-1.1e+06)bps) errors: 0
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the only driver which doesn't hand virtqueue_add_inbuf and
virtqueue_add_outbuf a well-formed, well-terminated sg. Fix it,
so we can make virtio_add_* simpler.
pktgen results:
modprobe pktgen
echo 'add_device eth0' > /proc/net/pktgen/kpktgend_0
echo nowait 1 > /proc/net/pktgen/eth0
echo count 1000000 > /proc/net/pktgen/eth0
echo clone_skb 100000 > /proc/net/pktgen/eth0
echo dst_mac 4e:14:25:a9:30:ac > /proc/net/pktgen/eth0
echo dst 192.168.1.2 > /proc/net/pktgen/eth0
for i in `seq 20`; do echo start > /proc/net/pktgen/pgctrl; tail -n1 /proc/net/pktgen/eth0; done
Before:
746547-793084(786421+/-9.6e+03)pps 346-367(364.4+/-4.4)Mb/sec (346397808-367990976(3.649e+08+/-4.5e+06)bps) errors: 0
After:
767390-792966(785159+/-6.5e+03)pps 356-367(363.75+/-2.9)Mb/sec (356068960-367936224(3.64314e+08+/-3e+06)bps) errors: 0
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-09-12
This series contains updates to e1000, ixgbe and ixgbevf.
Mark provide two fixes to reduce compile warnings produce by ixgbe
and ixgbevf.
Alex provides two patches for ixgbe, first removes the receive buffer
allocation at the end of the ixgbe_clean_rx_irq(). The reason for
removing this is to avoid the extra latency introduced by the MMIO write.
Second patch addresses several issues in the current ixgbe implementation
of busy poll sockets. It was possible for frames to be delivered out of
order if they were held in GRO, so address this by flushing the GRO
buffers before releasing the q_vector back to the idle state. Also, we
were having to take a spinlock on changing the state to and from idle,
so to resolve this, replaced the state value with an atomic and use
atomic_cmpxchg to change the value from idle, and a simple atomic set
to restore it back to idle after we have acquired it. This allows us
to only use a locked operation on acquiring the vector without a need
for a locked operation to release it.
Florian Westphal provides several patches for e1000 which does some
cleanup and updating of the driver. Moved e1000_tbi_adjust_stats()
so that he could make the function static. Added a helper function
to deal with the tbi workaround that was located in 2 different
Rx clean functions. Added a e1000_rx_buffer struct for use on receive
since the transmit and receive have different requirements. Updates
e1000 to use napi_gro_frags API.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend says:
====================
net/sched rcu classifiers and tcf
This series converts the tcf_proto usage to RCU.
This requires updating each classifier individually to handle the
new copy/update requirement and also to update the core list
traversals. This makes the assumption that updates to the tables
are infrequent in comparison to the packet per second being
classified. On a 10Gbps running near line rate we can easily
produce 12+ million packets per second so IMO this is a reasonable
assumption. The updates are serialized by RTNL.
I have done some basic testing on this series and do not see any
immediate splats or issues. The patch series has been running
on my dev systems for a month or so now and I've not seen any
issues. Although my configurations are not overly complicated.
My test cases at this point cover all the filters with a
tight loop to add/remove filters. Some basic estimator tests
where I add an estimator to the qdisc and verify the statistics
accurate using pktgen. And finally I have a small script to
exercise the 'tc actions' interface. Feel free to send me more
tests off list and I can run them.
This is prep work to drop the qdisc lock with the first
target being the ingress qdisc. To be done is making the
tc actions RCU safe and statistics per cpu. These patches
are in the works.
Comments:
- Checkpatch is still giving errors on some >80 char lines I know
about this. IMO the way to fix this is to restructure the sched
code to avoid being so heavily indented. But doing this here
bloats the patchset and anyways there are already lots of >80
chars in these files. I would prefer to keep the patches as is
but let me know if others think I should fix these and I will.
A follow up patch set could restructure the code and fix this
throughout the code blocks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the cls_bpf classifier RCU safe. The tcf_lock
was being used to protect a list of cls_bpf_prog now this list
is RCU safe and updates occur with rcu_replace.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make cls_u32 classifier safe to run without holding lock. This patch
converts statistics that are kept in read section u32_classify into
per cpu counters.
This patch was tested with a tight u32 filter add/delete loop while
generating traffic with pktgen. By running pktgen on vlan devices
created on top of a physical device we can hit the qdisc layer
correctly. For ingress qdisc's a loopback cable was used.
for i in {1..100}; do
q=`echo $i%8|bc`;
echo -n "u32 tos: iteration $i on queue $q";
tc filter add dev p3p2 parent $p prio $i u32 match ip tos 0x10 0xff \
action skbedit queue_mapping $q;
sleep 1;
tc filter del dev p3p2 prio $i;
echo -n "u32 tos hash table: iteration $i on queue $q";
tc filter add dev p3p2 parent $p protocol ip prio $i handle 628: u32 divisor 1
tc filter add dev p3p2 parent $p protocol ip prio $i u32 \
match ip protocol 17 0xff link 628: offset at 0 mask 0xf00 shift 6 plus 0
tc filter add dev p3p2 parent $p protocol ip prio $i u32 \
ht 628:0 match ip tos 0x10 0xff action skbedit queue_mapping $q
sleep 2;
tc filter del dev p3p2 prio $i
sleep 1;
done
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This uses per cpu counters in cls_u32 in preparation
to convert over to rcu.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make cls_tcindex RCU safe.
This patch addds a new RCU routine rcu_dereference_bh_rtnl() to check
caller either holds the rcu read lock or RTNL. This is needed to
handle the case where tcindex_lookup() is being called in both cases.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RCUify the route classifier. For now however spinlock's are used to
protect fastmap cache.
The issue here is the fastmap may be read by one CPU while the
cache is being updated by another. An array of pointers could be
one possible solution.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RCU'ify fw classifier.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
