2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-23 12:43:55 +08:00
Commit Graph

376 Commits

Author SHA1 Message Date
Jamie Wellnitz
41415862a2 [SCSI] lpfc 8.1.2: Add ERROR and WARM_START modes for diagnostic purposes.
Add ERROR and WARM_START modes for diagnostic purposes.

Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-02-28 19:00:36 -06:00
Jamie Wellnitz
7f0b5b1913 [SCSI] lpfc 8.1.2: Correct use of the hostdata field in scsi_host
Correct use of the hostdata field in scsi_host

Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-02-28 18:58:02 -06:00
Jamie Wellnitz
901a920f07 [SCSI] lpfc 8.1.2: Fixed system panic in lpfc_sli_brdreset during dynamic add of LP11K
Fixed system panic in lpfc_sli_brdreset during dynamic add of LP11K

Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-02-28 18:55:24 -06:00
James.Smart@Emulex.Com
fefcb2b677 [SCSI] lpfc 8.1.1 : kill use of pci_read_config_xxx
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-12-13 18:35:50 -07:00
James.Smart@Emulex.Com
875fbdfe9b [SCSI] lpfc 8.1.1 : Add polled-mode support
- Add functionality to run in polled mode only. Includes run time
  attribute to enable mode.
- Enable runtime writable hba settings for coallescing and delay parameters

Customers have requested a mode in the driver to run strictly polled.
This is generally to support an environment where the server is extremely
loaded and is looking to reclaim some cpu cycles from adapter interrupt
handling.

This patch adds a new "poll" attribute, and the following behavior:

if value is 0 (default):
  The driver uses the normal method for i/o completion. It uses the
  firmware feature of interrupt coalesing. The firmware allows a
  minimum number of i/o completions before an interrupt, or a maximum
  time delay between interrupts.  By default, the driver sets these
  to no delay (disabled) or 1 i/o - meaning coalescing is disabled.

  Attributes were provided to change the coalescing values, but it was
  a module-load time only and global across all adapters.
  This patch allows them to be writable on a per-adapter basis.

if value is 1 :
  Interrupts are left enabled, expecting that the user has tuned the
  interrupt coalescing values. When this setting is enabled, the driver
  will attempt to service completed i/o whenever new i/o is submitted
  to the adapter. If the coalescing values are large, and the i/o
  generation rate steady, an interrupt will be avoided by servicing
  completed i/o prior to the coalescing thresholds kicking in. However,
  if the i/o completion load is high enough or i/o generation slow, the
  coalescion values will ensure that completed i/o is serviced in a timely
  fashion.

if value is 3 :
  Turns off FCP i/o interrupts altogether. The coalescing values now have
  no effect. A new attribute "poll_tmo" (default 10ms) exists to set
  the polling interval for i/o completion. When this setting is enabled,
  the driver will attempt to service completed i/o and restart the
  interval timer whenever new i/o is submitted. This behavior allows for
  servicing of completed i/o sooner than the interval timer, but ensures
  that if no i/o is being issued, then the interval timer will kick in
  to service the outstanding i/o.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-12-13 18:34:14 -07:00
James.Smart@Emulex.Com
5cc36b3cd0 [SCSI] lpfc 8.1.1 : Bring model descriptions in sync with Emulex standard generic names
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-12-13 18:27:57 -07:00
James.Smart@Emulex.Com
e4adb20406 [SCSI] lpfc 8.1.1 : Add support for more members of the Light Pulse 11xxx (4Gb) family
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-12-13 18:27:22 -07:00
James.Smart@Emulex.Com
6175c02a0b [SCSI] lpfc 8.1.1 : Fixes to error handlers
- Release task management command before counting outstanding commands.
  TMF was being erroneously counted as an active outstanding command.
- Serialize EH calls and block requests when EH function is running.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-12-13 18:26:47 -07:00
James.Smart@Emulex.Com
6281bfe000 [SCSI] lpfc 8.1.1 : Fixes for short cable pulls
Cause: Link bounces were causing discovery ELS's to be killed.
Driver was not properly flushing ELS commands upon the subsequent
link bounces. Thus, processing of ELS post link bounce erroneously
assumed discovery failure and device loss.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-12-13 18:16:01 -07:00
James.Smart@Emulex.Com
1de933f35b [SCSI] lpfc 8.1.1: Miscellaneous Cleanups
Miscellaneous Cleanups:
- Remove ProgType READ_REV mailbox command value check in lpfc_config_port_prep.
- Convert simple printk to an lpfc_printf_log in queuecommand.
- Modify lpfc_abort_handler message 0749 to display more accurate text and data.
- Minor style cleanup: fix 3 long lines in lpfc_hw.h

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-12-13 18:14:08 -07:00
Jeff Garzik
a5cf8b7dc5 [PATCH] lpfc build fix
Current upstream 'allmodconfig' build is broken.  This is the obvious
patch...

Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-11-10 21:25:04 -08:00
Jesper Juhl
c9475cb0c3 [PATCH] kfree cleanup: drivers/scsi
This is the drivers/scsi/ part of the big kfree cleanup patch.

Remove pointless checks for NULL prior to calling kfree() in drivers/scsi/.

Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-11-07 07:54:01 -08:00
James.Smart@Emulex.Com
73797e31b5 [SCSI] lpfc 8.1.0 : Add owner field to struct pci_driver
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-10-29 10:32:49 -05:00
James.Smart@Emulex.Com
0bd4ca25ad [SCSI] lpfc: Fix eh_ return codes for commands
Return FAILED from eh_ routines if command(s) is(are) not completed

There were scenarios where we may have returned from the error
handlers prior to all affected commands being flushed to the midlayer.
Add changes to ensure this doesn't happen.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-10-29 10:31:48 -05:00
James Bottomley
604a3e3042 [SCSI] lpfc: Fix for "command completion for iotax x?? not found"
From: James Smart <James.Smart@emulex.com>

There were scenarios where the error handlers could reuse an iotag
value of an active io.  Remove all possibility of this by
pre-assigning iotag resources to command resources.

Signed-off-by: James Smart <James.Smart@emulex.com>

Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-10-29 10:28:33 -05:00
James.Smart@Emulex.Com
f91b392c4d [SCSI] lpfc: Fix for "Unknown IOCB command Data: x0 x3 x0 x0"
Fix for "Unknown IOCB command Data: x0 x3 x0 x0" messages and
inability to see devices

On some platforms, the host-memory based ring mgmt area was not
zero. Also, driver wasn't manipulating the entire 32bits of the ring
pointers.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-10-29 10:19:52 -05:00
James.Smart@Emulex.Com
964b77e776 [SCSI] lpfc: Update to Emulex hba model names
Update adapter names to match Emulex naming conventions.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-10-29 10:10:44 -05:00
James.Smart@Emulex.Com
19a7b4aebf [SCSI] update fc_transport for removal of block/unblock functions
We recently went back to implement a board reset. When we perform the
reset, we wanted to tear down the internal data structures and rebuild
them. Unfortunately, when it came to the rport structure, things were
odd. If we deleted them, the scsi targets and sdevs would be
torn down. Not a good thing for a temporary reset. We could block the
rports, but we either maintain the internal structures to keep the
rport reference (perhaps even replicating what's in the transport),
or we have to fatten the fc transport with new search routines to find
the rport (and deal with a case of a dangling rport that the driver
forgets).

It dawned on me that we had actually reached this state incorrectly.
When the fc transport first started, we did the block/unblock first, then
added the rport interface. The purpose of block/unblock is to hide the
temporary disappearance of the rport (e.g. being deleted, then readded).
Why are we making the driver do the block/unblock ? We should be making
the transport have only an rport add/delete, and the let the transport
handle the block/unblock.

So... This patch removes the existing fc_remote_port_block/unblock
functions. It moves the block/unblock functionality into the
fc_remote_port_add/delete functions.  Updates for the lpfc driver are
included. Qlogic driver updates are also enclosed, thanks to the
contributions of Andrew Vasquez. [Note: the qla2xxx changes are
relative to the scsi-misc-2.6 tree as of this morning - which does
not include the recent patches sent by Andrew]. The zfcp driver does
not use the block/unblock functions.

One last comment: The resulting behavior feels very clean. The LLDD is
concerned only with add/delete, which corresponds to the physical
disappearance.  However, the fact that the scsi target and sdevs are
not immediately torn down after the LLDD calls delete causes an
interesting scenario... the midlayer can call the xxx_slave_alloc and
xxx_queuecommand functions with a sdev that is at the location the
rport used to be. The driver must validate the device exists when it
first enters these functions. In thinking about it, this has always
been the case for the LLDD and these routines. The existing drivers
already check for existence. However, this highlights that simple
validation via data structure dereferencing needs to be watched.
To deal with this, a new transport function, fc_remote_port_chkready()
was created that LLDDs should call when they first enter these two
routines. It validates the rport state, and returns a scsi result
which could be returned. In addition to solving the above, it also
creates consistent behavior from the LLDD's when the block and deletes
are occuring.

Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-10-28 21:20:07 -05:00
Andrew Morton
68ce1eb540 [SCSI] lpfc build fix
gcc-2.95.x doesn't do anonymous unions.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-09-21 16:25:46 -05:00
Andrew Vasquez
f631b4be76 [SCSI] lpfc: use wwn_to_u64() transport helper
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Acked-by: Smart, James <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-09-10 11:11:48 -05:00
James.Smart@Emulex.Com
918865230e [SCSI] lpfc driver 8.0.30 : convert to use of int_to_scsilun()
Replace use of lpfc_put_lun with midlayer's int_to_scsilun

Remove driver's local definition of lpfc_put_lun (which converts an
int back to a 64-bit LUN) and replace it's use with the recently added
int_to_scsilun function provided by the midlayer.

Note: Embedding midlayer structure in our structure caused
need for more files to include midlayer headers.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-08-12 12:09:01 -05:00
James.Smart@Emulex.Com
f888ba3ce7 [SCSI] lpfc driver 8.0.30 : fix get_stats panic
Fix panic in lpfc_get_stats()

Symptoms: Panic on sysfs stats access

Cause: In lpfc_get_stats() we are writing to memory that we do not
own.

Fix: Fix our stats structure allocation. Embed phba->link_stats in
struct lpfc_hba and stop treating it like rogue structure.

Note: Embedding midlayer/transport structure in our structure caused
need for more files to include midlayer/transport headers.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-08-12 12:08:48 -05:00
James.Smart@Emulex.Com
c44ce17374 [SCSI] lpfc: Update copyright notices
Update copyright notice text and include year 2005.

Add Copyright notice for Christoph Hellwig to several files: lpfc.h
lpfc_attr.c lpfc_els.c lpfc_hbadisc.c lpfc_init.c lpfc_mbox.c
lpfc_mem.c lpfc_nportdisc.c lpfc_scsi.c lpfc_sli.c

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-07-02 19:08:29 -05:00
James.Smart@Emulex.Com
5542134f61 [SCSI] lpfc: Remove $Id$ keyword strings.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-07-02 19:06:16 -05:00
James.Smart@Emulex.Com
06325e7459 [SCSI] lpfc: Add LP6000 PCI ID
Fix driver not seeing LP6000.  Fix: add PCI id to the pci_device_id
table and a short description for the HBA in get_hba_model_desc().
Also add a default clause to the switch statement that parses the
various PCI ID's.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-07-02 17:18:52 -05:00
dea3101e0a lpfc: add Emulex FC driver version 8.0.28
From: 	James.Smart@Emulex.Com

Modified for kernel import and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-04-18 13:50:53 -05:00