When sending HCI data over NCI, HCI return code is part
of the NCI data. In order to get correctly the HCI return
code, we assume the NCI communication is successful and
extract the return code for the nci_hci functions return code.
This is done because nci_to_errno does not match hci return
code value.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When sending HCI data over NCI, cmd information should be
present only on the first packet.
Each packet shall be specifically allocated and sent to the
NCI layer.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This functin takes as a parameter a pointer to the nci_dev
struct and the first byte from the values of the first domain
specific parameter that was used for the connection creation.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the number of destination speific parameters supplied is 0
the call will fail. If the first destination specific parameter
does not have a value, curr_id will be set to 0.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Initially it was used to create hooks in the driver for
proprietary operations. Currently it is being used for hooks
for both proprietary and generic operations.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver may be required to act when some responses or
notifications arrive. For example the NCI core does not have a
handler for NCI_OP_CORE_GET_CONFIG_RSP. The NFCC can send a
config response that has to be read by the driver and the packet
may contain vendor specific data.
The Fields Peak driver needs to take certain actions when a reset
notification arrives (packet also not handled by the nfc core).
The driver handlers do not interfere with the core and they are
called after the core processes the packet.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This allows sending core commands from the driver. The driver
should be able to send NCI core commands like CORE_GET_CONFIG_CMD.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver should know that it can continue with post setup where
setup left off. Being able to execute post_setup when setup fails
may force the developer to keep this state in the driver.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
FDP driver needs to send the firmware as regular packets
(not fragmented). The driver should have a way to
get the max packet size for a given connection.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For the firmware update the driver may use nci_send_data.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The exit label performs device_unlock(&dev->dev);, which will fail when dev
is NULL, and nfc_put_device(dev);, which is not useful when dev is NULL, so
just exit the function immediately.
Problem found using scripts/coccinelle/null/deref_null.cocci
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since we do not know in which context drivers will call these
routines, they should use the unlocked version of nci_request,
i.e. __nci_request.
It is up to drivers to know/decide if they need to take the
req_lock mutex before calling those routines. When being called
from the NCI setup routine there is no need to do so as ops->setup
is called under req_lock.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A proprietary vendor command may send back useful data to the user
application.
For example, the field level applied on the NFC router antenna.
Still based on net/wireless/nl80211.c implementation,
add nfc_vendor_cmd_alloc_reply_skb and nfc_vendor_cmd_reply in
order to send back over netlink data generated by a proprietary
command.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
skb can be NULL and may lead to a NULL pointer error.
Add a check condition before setting HCI rx buffer.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some drivers needs to have ability to reinit NCI core, for example
after updating firmware in setup() of post_setup() callback. This
patch makes nci_core_reset() and nci_core_init() functions public,
to make it possible.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some drivers require non-standard configuration after NCI_CORE_INIT
request, because they need to know ndev->manufact_specific_info or
ndev->manufact_id. This patch adds post_setup handler allowing to do
such custom configuration.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When NFC_ATTR_VENDOR_DATA is not set, data_len is 0 and data is NULL.
Fixes the following warning:
net/nfc/netlink.c:1536:3: warning: 'data' may be used uninitialized
+in this function [-Wmaybe-uninitialized]
return cmd->doit(dev, data, data_len);
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC_ATTR_VENDOR_DATA is an optional vendor_cmd argument.
The current code was potentially using a non existing argument
leading to potential catastrophic results.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It was not possible to register a UART driver due
to a bad condition.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NCI deactivate management was modified to support all NCI
deactivation type. Problem is that all the API are not ready
yet for it.
Problem is that with current code, when neard asks to deactivate
the tag it sends a deactivate SLEEP but nobody will then send a
IDLE deactivate. This IDLE deactivate is mandatory since NFC
controller can only be unlocked by DH.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support of Marvell NFC chip controlled over UART
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some NFC controller supports UART as host interface.
As with SPI, a lot of code can be shared between vendor
drivers. This patch add the generic support of UART and
provides some extension API for vendor specific needs.
This code is strongly inspired by the Bluetooth HCI ldisc
implementation. NCI UART vendor drivers will have to register
themselves to this layer via nci_uart_register.
Underlying tty will have to be configured from user land
thanks to an ioctl.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Vendor commands are passed from userspace through the
NFC_CMD_VENDOR netlink command, allowing driver and hardware
specific operations implementations like for example RF tuning
or production line calibration.
Drivers will associate a set of vendor commands to a vendor
id, which could typically be an OUI. The netlink kernel
implementation will try to match the received vendor id
and sub command attributes with the registered ones. When
such match is found, the driver defined sub command routine
is called.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When closing the device some data (proprietary commands)
might be sent. The core state machine needs to be set for
correct command execution.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Handle allowing to send proprietary nci commands anywhere in the nci
state machine.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some device may need to execute some proprietary commands
in order to "wake-up"; Before the nci state initialization.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
setup was executed in any case, even if NCI_RESET failed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow for drivers to explicitly define handlers for each
proprietary notifications and responses they expect to support.
Reviewed-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Several of these goto exit; uses should be direct returns
as skb is not yet initialized by nci_hci_get_param().
Miscellanea:
o Use !memcmp instead of memcmp() == 0
o Remove unnecessary goto from if () {... goto exit;} else {...} exit:
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In preparation for changing how struct net is refcounted
on kernel sockets pass the knowledge that we are creating
a kernel socket from sock_create_kern through to sk_alloc.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
portid is an unsigned integer. Fix urelease_work to
match all other portid user in the kernel.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
A simple forward for firmware download (i.e. sending a new firmware
to the NFC adapter) from the NFC subsystem to the drivers.
This feature is required to update the firmware of NXP-NCI NFC
controllers but can be used by any NCI driver.
This feature has been present in the HCI subsystem since 9a695d.
Signed-off-by: Clément Perrochaud <clement.perrochaud@effinnov.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
After TIPC doesn't depend on iocb argument in its internal
implementations of sendmsg() and recvmsg() hooks defined in proto
structure, no any user is using iocb argument in them at all now.
Then we can drop the redundant iocb argument completely from kinds of
implementations of both sendmsg() and recvmsg() in the entire
networking stack.
Cc: Christoph Hellwig <hch@lst.de>
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFCEE_DISCOVER_CMD is a specified NCI command used to discover
NFCEE IDs.
Move nci_nfcee_discover() call to nci_discover_se() in order to
guarantee:
- NFCEE_DISCOVER_CMD run when the NCI state machine is initialized
- NFCEE_DISCOVER_CMD is not run in case there is not discover_se
hook defined by a NFC device driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
conn_info is currently allocated only after nfcee_discovery_ntf
which is not generic enough for logical connection other than
NFCEE. The corresponding conn_info is now created in
nci_core_conn_create_rsp().
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For consistency sake change nci_core_conn_create_rsp structure
credits field to credits_cnt.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current implementation limits nci_core_conn_create_req()
to only manage NCI_DESTINATION_NFCEE.
Add new parameters to nci_core_conn_create() to support all
destination types described in the NCI specification.
Because there are some parameters with variable size dynamic
buffer allocation is needed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The NCI_STATIC_RF_CONN_ID logical connection is the most used
connection. Keeping it directly accessible in the nci_dev
structure will simplify and optimize the access.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When receiving an interface activation notification, if
the RF interface is NCI_RF_INTERFACE_NFCEE_DIRECT, we
need to ignore the following parameters and change the NCI
state machine to NCI_LISTEN_ACTIVE. According to the NCI
specification, the parameters should be 0 and shall be
ignored.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The NFCC sends an NCI_OP_RF_NFCEE_ACTION_NTF notification
to the host (DH) to let it know that for example an RF
transaction with a payment reader is done.
For now the notification handler is empty.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC_EVT_TRANSACTION is sent through netlink in order for a
specific application running on a secure element to notify
userspace of an event. Typically the secure element application
counterpart on the host could interpret that event and act
upon it.
Forwarded information contains:
- SE host generating the event
- Application IDentifier doing the operation
- Applications parameters
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to the NCI specification, one can use HCI over NCI
to talk with specific NFCEE. The HCI network is viewed as one
logical NFCEE.
This is needed to support secure element running HCI only
firmwares embedded on an NCI capable chipset, like e.g. the
st21nfcb.
There is some duplication between this piece of code and the
HCI core code, but the latter would need to be abstracted even
more to be able to use NCI as a logical transport for HCP packets.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to communicate with an NFCEE, we need to open a logical
connection to it, by sending the NCI_OP_CORE_CONN_CREATE_CMD
command to the NFCC. It's left up to the drivers to decide when
to close an already opened logical connection.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFCEEs can be enabled or disabled by sending the
NCI_OP_NFCEE_MODE_SET_CMD command to the NFCC. This patch
provides an API for drivers to enable and disable e.g. their
NCI discoveredd secure elements.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFCEEs (NFC Execution Environment) have to be explicitly
discovered by sending the NCI_OP_NFCEE_DISCOVER_CMD
command. The NFCC will respond to this command by telling
us how many NFCEEs are connected to it. Then the NFCC sends
a notification command for each and every NFCEE connected.
Here we implement support for sending
NCI_OP_NFCEE_DISCOVER_CMD command, receiving the response
and the potential notifications.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current NCI core only support the RF static connection.
For other NFC features such as Secure Element communication, we
may need to create logical connections to the NFCEE (Execution
Environment.
In order to track each logical connection ID dynamically, we add a
linked list of connection info pointers to the nci_dev structure.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the newly introduced pipes table hci_dev fields,
the nfc_hci_pipe2gate routine is no longer needed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When a command is received, it is sometime needed to let the CLF driver do
some additional operations. (ex: count remaining pipe notification...)
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We update the tracked pipes status when receiving HCI commands.
Also we forward HCI errors and we reply to any HCI command, even though
we don't support it.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As there can be several pipes connected to the same gate, we need
to know which pipe ID to use when sending an HCI response. A gate
ID is not enough.
Instead of changing the nfc_hci_send_response() API to something
not aligned with the rest of the HCI API, we call nfc_hci_hcp_message_tx
directly.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to keep host source information on specific hci event (such as
evt_connectivity or evt_transaction) and because 2 pipes can be connected
to the same gate, it is necessary to add a table referencing every pipe
with a {gate, host} tuple.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Several pipes may point to the same CLF gate, so getting the gate ID
as an input is not enough.
For example dual secure element may have 2 pipes (1 for uicc and
1 for eSE) pointing to the connectivity gate.
As resolving gate and host IDs can be done from a pipe, we now pass
the pipe ID to the event received handler.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove one useless blank line at beginning of nfc_disable_se function.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove one useless blank line at beginning of nfc_enable_se function.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.
This makes the very common pattern of
if (genlmsg_end(...) < 0) { ... }
be a whole bunch of dead code. Many places also simply do
return nlmsg_end(...);
and the caller is expected to deal with it.
This also commonly (at least for me) causes errors, because it is very
common to write
if (my_function(...))
/* error condition */
and if my_function() does "return nlmsg_end()" this is of course wrong.
Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.
Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did
- return nlmsg_end(...);
+ nlmsg_end(...);
+ return 0;
I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.
One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-12-08
Please pull this last batch of pending wireless updates for the 3.19 tree...
For the wireless bits, Johannes says:
"This time I have Felix's no-status rate control work, which will allow
drivers to work better with rate control even if they don't have perfect
status reporting. In addition to this, a small hwsim fix from Patrik,
one of the regulatory patches from Arik, and a number of cleanups and
fixes I did myself.
Of note is a patch where I disable CFG80211_WEXT so that compatibility
is no longer selectable - this is intended as a wake-up call for anyone
who's still using it, and is still easily worked around (it's a one-line
patch) before we fully remove the code as well in the future."
For the Bluetooth bits, Johan says:
"Here's one more bluetooth-next pull request for 3.19:
- Minor cleanups for ieee802154 & mac802154
- Fix for the kernel warning with !TASK_RUNNING reported by Kirill A.
Shutemov
- Support for another ath3k device
- Fix for tracking link key based security level
- Device tree bindings for btmrvl + a state update fix
- Fix for wrong ACL flags on LE links"
And...
"In addition to the previous one this contains two more cleanups to
mac802154 as well as support for some new HCI features from the
Bluetooth 4.2 specification.
From the original request:
'Here's what should be the last bluetooth-next pull request for 3.19.
It's rather large but the majority of it is the Low Energy Secure
Connections feature that's part of the Bluetooth 4.2 specification. The
specification went public only this week so we couldn't publish the
corresponding code before that. The code itself can nevertheless be
considered fairly mature as it's been in development for over 6 months
and gone through several interoperability test events.
Besides LE SC the pull request contains an important fix for command
complete events for mgmt sockets which also fixes some leaks of hci_conn
objects when powering off or unplugging Bluetooth adapters.
A smaller feature that's part of the pull request is service discovery
support. This is like normal device discovery except that devices not
matching specific UUIDs or strong enough RSSI are filtered out.
Other changes that the pull request contains are firmware dump support
to the btmrvl driver, firmware download support for Broadcom BCM20702A0
variants, as well as some coding style cleanups in 6lowpan &
ieee802154/mac802154 code.'"
For the NFC bits, Samuel says:
"With this one we get:
- NFC digital improvements for DEP support: Chaining, NACK and ATN
support added.
- NCI improvements: Support for p2p target, SE IO operand addition,
SE operands extensions to support proprietary implementations, and
a few fixes.
- NFC HCI improvements: OPEN_PIPE and NOTIFY_ALL_CLEARED support,
and SE IO operand addition.
- A bunch of minor improvements and fixes for STMicro st21nfcb and
st21nfca"
For the iwlwifi bits, Emmanuel says:
"Major works are CSA and TDLS. On top of that I have a new
firmware API for scan and a few rate control improvements.
Johannes find a few tricks to improve our CPU utilization
and adds support for a new spin of 7265 called 7265D.
Along with this a few random things that don't stand out."
And...
"I deprecate here -8.ucode since -9 has been published long ago.
Along with that I have a new activity, we have now better
a infrastructure for firmware debugging. This will allow to
have configurable probes insides the firmware.
Luca continues his work on NetDetect, this feature is now
complete. All the rest is minor fixes here and there."
For the Atheros bits, Kalle says:
"Only ath10k changes this time and no major changes. Most visible are:
o new debugfs interface for runtime firmware debugging (Yanbo)
o fix shared WEP (Sujith)
o don't rebuild whenever kernel version changes (Johannes)
o lots of refactoring to make it easier to add new hw support (Michal)
There's also smaller fixes and improvements with no point of listing
here."
In addition, there are a few last minute updates to ath5k,
ath9k, brcmfmac, brcmsmac, mwifiex, rt2x00, rtlwifi, and wil6210.
Also included is a pull of the wireless tree to pick-up the fixes
originally included in "pull request: wireless 2014-12-03"...
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum size of ATR_REQ and ATR_RES is 64 bytes.
The maximum number of General Bytes is calculated by
the maximum number of data bytes in the ATR_REQ/ATR_RES,
substracted by the number of mandatory data bytes.
ATR_REQ: 16 mandatory data bytes, giving a maximum of
48 General Bytes.
ATR_RES: 17 mandatory data bytes, giving a maximum of
47 General Bytes.
Regression introduced in commit a99903ec.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixing: net/nfc/nci/ntf.c:106:31: warning: cast to restricted __le16
message when building with make C=1 CF=-D__CHECK_ENDIAN__
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix warnings:
net/nfc/llcp_commands.c:421:14: warning: incorrect type in assignment (different base types)
net/nfc/llcp_commands.c:421:14: expected unsigned short [unsigned] [usertype] miux
net/nfc/llcp_commands.c:421:14: got restricted __be16
net/nfc/llcp_commands.c:477:14: warning: incorrect type in assignment (different base types)
net/nfc/llcp_commands.c:477:14: expected unsigned short [unsigned] [usertype] miux
net/nfc/llcp_commands.c:477:14: got restricted __be16
Procedure to reproduce:
make ARCH=x86_64 allmodconfig
make C=1 CF=-D__CHECK_ENDIAN__
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some pipe are only created by other host (different than the
Terminal Host).
The pipe values will for example be notified by
NFC_HCI_ADM_NOTIFY_PIPE_CREATED.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
se_io allows to send apdu over the CLF to the embedded
Secure Element.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some tag might get deactivated after some read or write tentative.
This may happen for example with Mifare Ultralight C tag when trying
to read the last 4 blocks (starting block 0x2c) configured as write
only.
NFC_CMD_ACTIVATE_TARGET will try to reselect the tag in order to
detect if it got remove from the field or if it is still present.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
nci_rf_deactivate_req only support NCI_DEACTIVATE_TYPE_IDLE_MODE.
In some situation, it might be necessary to be able to support other
NCI_DEACTIVATE_TYPE such as NCI_DEACTIVATE_TYPE_SLEEP_MODE in order for
example to reactivate the selected target.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A notification for rf deaction can be IDLE_MODE, SLEEP_MODE,
SLEEP_AF_MODE and DISCOVERY. According to each type and the NCI
state machine is different (see figure 10 RF Communication State
Machine in NCI specification)
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The nci status byte was ignored. In case of tag reading for example,
if the tag is removed from the antenna there is no way for the upper
layers (aka: stack) to get inform about such event.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When switching from UICC to another, the CLF may signals to the Terminal
Host that some existing pipe are cleared for future update.
This notification needs to be "acked" by the Terminal Host with a ANY_OK
message.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If our terminal connect with other host like UICC, it may create
a pipe with us, the host controller will notify us new pipe
created, after that UICC will open that pipe, if we don't handle
that request, UICC may failed to continue initialize which may
lead to card emulation feature failed to work
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
se_io allows to send apdu over the CLF to the embedded Secure Element.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some NFC controller using NCI protocols may need a proprietary commands
flow to disable a secure element
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some NFC controller using NCI protocols may need a proprietary commands
flow to enable a secure element
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some NFC controller using NCI protocols may need a proprietary commands
flow to discover all available secure element
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix sparse warning introduced by commit: 9e87f9a9c4
It was generating the following warning:
net/nfc/nci/ntf.c:170:7: sparse: symbol 'nci_get_prop_rf_protocol' was not declared. Should it be static?
Procedure to reproduce it:
# apt-get install sparse
git checkout 9e87f9a9c4
make ARCH=x86_64 allmodconfig
make C=1 CF=-D__CHECK_ENDIAN__
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
se_io allows to send apdu over the CLF to the embedded Secure Element.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Before signaling the deactivation, send a deactivation request if in
RFST_DISCOVERY state because neard assumes polling is stopped and will
try to restart it.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the deactivation type reported by RF_DEACTIVATE_NTF is Discovery, go in
RFST_DISCOVERY state. The NFCC stays in Poll mode and/or Listen mode.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As specified in NCI 1.0 and NCI 1.1, when using the NFC-DEP RF Interface, the
DH and the NFCC shall only use the Static RF Connection for data communication
with a Remote NFC Endpoint.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Target responds to the ATR_REQ with the ATR_RES. Configure the General
Bytes in ATR_RES with the first three octets equal to the NFC Forum LLCP
magic number, followed by some LLC Parameters TLVs described in section
4.5 of [LLCP].
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Changes:
* Extract the Listen mode activation parameters from RF_INTF_ACTIVATED_NTF.
* Store the General Bytes of ATR_REQ.
* Signal that Target mode is activated in case of an activation in NFC-DEP.
* Update the NCI state accordingly.
* Use the various constants defined in nfc.h.
* Fix the ATR_REQ and ATR_RES maximum size. As per NCI 1.0 and NCI 1.1, the
Activation Parameters for both Poll and Listen mode contain all the bytes of
ATR_REQ/ATR_RES starting and including Byte 3 as defined in [DIGITAL].
In [DIGITAL], the maximum size of ATR_REQ/ATR_RES is 64 bytes and they are
numbered starting from Byte 1.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Send LA_SEL_INFO and LF_PROTOCOL_TYPE with NFC-DEP protocol enabled.
Configure 212 Kbit/s and 412 Kbit/s bit rates for Listen F.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Target mode protocols are given to the nci_start_poll() function
but were previously ignored.
To enable P2P Target, when NFC-DEP is requested as a Target mode protocol, add
NFC-A and NFC-F Passive Listen modes in RF_DISCOVER_CMD command.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
list_for_each_entry_safe() is necessary if list objects are deleted from
the list while traversing it. Not the case here, so we can use the base
list_for_each_entry variant.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When an NFC-DEP target receives an ATN PDU, its
supposed to respond with a similar ATN PDU.
When the Target receives an I PDU with the PNI
one less than the current PNI and the last PDU
sent was an ATN PDU, the Target is to resend the
last non-ATN PDU that it has sent. This is
described in section 14.12.3.4 of the NFC Digital
Protocol Spec.
The digital layer's NFC-DEP code doesn't implement
this so add that support.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When an NFC-DEP Initiator times out when waiting for
a DEP_RES from the Target, its supposed to send an
ATN to the Target. The Target should respond to the
ATN with a similar ATN PDU and the Initiator can then
resend the last non-ATN PDU that it sent. No more
than 'N(retry,atn)' are to be send where
2 <= 'N(retry,atn)' <= 5. If the Initiator had just
sent a NACK PDU when the timeout occurred, it is to
continue sending NACKs until 'N(retry,nack)' NACKs
have been send. This is described in section
14.12.5.6 of the NFC-DEP Digital Protocol Spec.
The digital layer's NFC-DEP code doesn't implement
this so add that support.
The value chosen for 'N(retry,atn)' is 2.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When an NFC-DEP Target receives a NACK PDU with
a PNI equal to 1 less than the current PNI, it
is supposed to re-send the last PDU. This is
implied in section 14.12.5.4 of the NFC Digital
Protocol Spec.
The digital layer's NFC-DEP code doesn't implement
Target-side NACK handing so add it. The last PDU
that was sent is saved in the 'nfc_digital_dev'
structure's 'saved_skb' member. The skb will have
an additional reference taken to ensure that the skb
isn't freed when the driver performs a kfree_skb()
on the skb. The length of the skb/PDU is also saved
so the length can be restored when re-sending the PDU
in the skb (the driver will perform an skb_pull() so
an skb_push() needs to be done to restore the skb's
data pointer/length).
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When an NFC-DEP Initiator receives a frame with
an incorrect CRC or with a parity error, and the
frame is at least 4 bytes long, its supposed to
send a NACK to the Target. The Initiator can
send up to 'N(retry,nack)' consecutive NACKs
where 2 <= 'N(retry,nack)' <= 5. When the limit
is exceeded, a PROTOCOL EXCEPTION is raised.
Any other type of transmission error is to be
ignored and the Initiator should continue
waiting for a new frame. This is described
in section 14.12.5.4 of the NFC Digital Protocol
Spec.
The digital layer's NFC-DEP code doesn't implement
any of this so add it. This support diverges from
the spec in two significant ways:
a) NACKs will be sent for ANY error reported by the
driver except a timeout. This is done because
there is currently no way for the digital layer
to distinguish a CRC or parity error from any
other type of error reported by the driver.
b) All other errors will cause a PROTOCOL EXCEPTION
even frames with CRC errors that are less than 4
bytes.
The value chosen for 'N(retry,nack)' is 2.
Targets do not send NACK PDUs.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the peer in an NFC-DEP exchange has a
packet to send that is larger than the local
maximum payload, it sets the 'MI' bit in the
'I' PDU. This indicates that NFC-DEP chaining
is to occur.
When such a PDU is received, the local side
responds with an 'ACK' PDU and this continues
until the peer sends an 'I' PDU with the 'MI'
bit cleared. This indicates that the chaining
sequence is complete and the entire packet has
been transferred.
Receiving chained PDUs is currently not supported
by the digital layer so add that support. When a
chaining sequence is initiated by the peer, the
digital layer will allocate an skb large enough
to hold 8 maximum sized frame payloads. The maximum
payload can range from 64 to 254 bytes so 8 * 254 =
2032 seems like a reasonable compromise between
potentially wasting memory and constantly reallocating
new, larger skbs.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the NFC-DEP code is given a packet to send
that is larger than the peer's maximum payload,
its supposed to set the 'MI' bit in the 'I' PDU's
Protocol Frame Byte (PFB). Setting this bit
indicates that NFC-DEP chaining is to occur.
When NFC-DEP chaining is progress, sender 'I' PDUs
are acknowledged with 'ACK' PDUs until the last 'I'
PDU in the chain (which has the 'MI' bit cleared)
is responded to with a normal 'I' PDU. This can
occur while in Initiator mode or in Target mode.
Sender NFC-DEP chaining is currently not implemented
in the digital layer so add that support. Unfortunately,
since sending a frame may require writing the CRC to the
end of the data, the relevant data part of the original
skb must be copied for each intermediate frame.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The maximum payload for NFC-DEP exchanges (i.e., the
number of bytes between SoD and EoD) is negotiated
using the ATR_REQ, ATR_RES, and PSL_REQ commands.
The valid maximum lengths are 64, 128, 192, and 254
bytes.
Currently, NFC-DEP code assumes that both sides are
always using 254 byte maximums and ignores attempts
by the peer to change it. Instead, implement the
negotiation code, enforce the local maximum when
receiving data from the peer, and don't send payloads
that exceed the remote's maximum. The default local
maximum is 254 bytes.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC-DEP DEP_REQ and DEP_RES exchanges using 'I'
and 'ACK/NACK' PDUs have a sequence number called
the Packet Number Information (PNI). The PNI
is incremented (modulo 4) after every DEP_REQ/
DEP_RES pair and should be verified by the digital
layer code. That verification isn't always done,
though, so add code to make sure that it is done.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to chapter 14 of the NFC-DEP Digital
Protocol Spec., the NAD byte should never be
present in DEP_REQ or DEP_RES frames. However,
this is not enforced so add that enforcement code.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When in Target mode, the Initiator specifies whether
subsequent DEP_REQ and DEP_RES frames will include
a DID byte by the value passed in the ATR_REQ. If
the DID value in the ATR_REQ is '0' then no DID
byte will be included. If the DID value is between
'1' and '14' then a DID byte containing the same
value must be included in subsequent DEP_REQ and
DEP_RES frames. Any other DID value is invalid.
This is specified in sections 14.8.1.2 and 14.8.2.2
of the NFC Digital Protocol Spec.
Checking the DID value (if it should be there at all),
is not currently supported by the digital layer's
NFC-DEP code. Add this support by remembering the
DID value in the ATR_REQ, checking the DID value of
received DEP_REQ frames (if it should be there at all),
and including the remembered DID value in DEP_RES
frames when appropriate.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When in Initiator mode, the digital layer's
NFC-DEP code always sets the Device ID (DID)
value in the ATR_REQ to '0'. This means that
subsequent DEP_REQ and DEP_RES frames must
never include a DID byte. This is specified
in sections 14.8.1.1 and 14.8.2.1 of the NFC
Digital Protocol Spec.
Currently, the digital layer's NFC-DEP code
doesn't enforce this rule so add code to ensure
that there is no DID byte in DEP_RES frames.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rearrange some of the code in digital_in_recv_dep_res()
and digital_tg_recv_dep_req() so the initial code looks
similar. The real reason is prepare the code for some
upcoming patches that require these changes.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When digital_in_send_cmd() or digital_tg_send_cmd()
fail, they do not free the skb that was passed to
them so the routine that allocated the skb should
free it. Currently, there are several routines in
the NFC-DEP code that don't do this so make them.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This encapsulates all of the skb_copy_datagram_iovec() callers
with call argument signature "skb, offset, msghdr->msg_iov, length".
When we move to iov_iters in the networking, the iov_iter object will
sit in the msghdr.
Having a helper like this means there will be less places to touch
during that transformation.
Based upon descriptions and patch from Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>
In NFC Forum NCI specification, some RF Protocol values are
reserved for proprietary use (from 0x80 to 0xfe).
Some CLF vendor may need to use one value within this range
for specific technology.
Furthermore, some CLF may not becompliant with NFC Froum NCI
specification 2.0 and therefore will not support RF Protocol
value 0x06 for PROTOCOL_T5T as mention in a draft specification
and in a recent push.
Adding get_rf_protocol handle to the nci_ops structure will
help to set the correct technology to target.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NCI RF FRAME interface is used for all kind of tags
except ISODEP ones. So for all other kind of tags the
status byte has to be removed.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
All contexts have to be initiliazed before calling
nfc_register_device otherwise it is possible to call
nci_dev_up before ending the nci_register_device
function. In such case kernel will crash on non
initialized variables.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to operate at the fasted bit rate
possible, add initiator-side support for
PSL REQ while in P2P mode. The PSL REQ
will switch the RF technology to 424F
whenever possible.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Conflicts:
net/6lowpan/iphc.c
Minor conflicts in iphc.c were changes overlapping with some
style cleanups.
John W. Linville says:
====================
Please pull this last(?) batch of wireless change intended for the
3.17 stream...
For the NFC bits, Samuel says:
"This is a rather quiet one, we have:
- A new driver from ST Microelectronics for their NCI ST21NFCB,
including device tree support.
- p2p support for the ST21NFCA driver
- A few fixes an enhancements for the NFC digital laye"
For the Atheros bits, Kalle says:
"Michal and Janusz did some important RX aggregation fixes, basically we
were missing RX reordering altogether. The 10.1 firmware doesn't support
Ad-Hoc mode and Michal fixed ath10k so that it doesn't advertise Ad-Hoc
support with that firmware. Also he implemented a workaround for a KVM
issue."
For the Bluetooth bits, Gustavo and Johan say:
"To quote Gustavo from his previous request:
'Some last minute fixes for -next. We have a fix for a use after free in
RFCOMM, another fix to an issue with ADV_DIRECT_IND and one for ADV_IND with
auto-connection handling. Last, we added support for reading the codec and
MWS setting for controllers that support these features.'
Additionally there are fixes to LE scanning, an update to conform to the 4.1
core specification as well as fixes for tracking the page scan state. All
of these fixes are important for 3.17."
And,
"We've got:
- 6lowpan fixes/cleanups
- A couple crash fixes, one for the Marvell HCI driver and another in LE SMP.
- Fix for an incorrect connected state check
- Fix for the bondable requirement during pairing (an issue which had
crept in because of using "pairable" when in fact the actual meaning
was "bondable" (these have different meanings in Bluetooth)"
Along with those are some late-breaking hardware support patches in
brcmfmac and b43 as well as a stray ath9k patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The digital layer of the NFC subsystem currently
supports a 'tg_listen_mdaa' driver hook that supports
devices that can do mode detection and automatic
anticollision. However, there are some devices that
can do mode detection but not automatic anitcollision
so add the 'tg_listen_md' hook to support those devices.
In order for the digital layer to get the RF technology
detected by the device from the driver, add the
'tg_get_rf_tech' hook. It is only valid to call this
hook immediately after a successful call to 'tg_listen_md'.
CC: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
stop_poll allows to stop CLF reader polling. Some other operations might be
necessary for some CLF to stop polling. For example in card mode.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add T1T matching with Jewel during notification.
It was causing "the target found does not have the desired protocol"
to show up.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add new "NFC_DIGITAL_FRAMING_*" calls to the digital
layer so the driver can make the necessary adjustments
when performing anticollision while in target mode.
The driver must ensure that the effect of these calls
happens after the following response has been sent but
before reception of the next request begins.
Acked-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently, digital_target_found() has a race between
the events started by calling nfc_targets_found()
(which ultimately expect ddev->poll_tech_count to be
zero) and setting ddev->poll_tech_count to zero after
the call to nfc_targets_found(). When the race is
"lost" (i.e., ddev->poll_tech_count is found to not
be zero by the events started by nfc_targets_found()),
an error message is printed and the target is not found.
A similar race exists when digital_tg_recv_atr_req()
calls nfc_tm_activated().
Fix this by first saving the current value of
ddev->poll_tech_count and then clearing it before
calling nfc_targets_found()/nfc_tm_activated().
Clearing ddev->poll_tech_count before calling
nfc_targets_found()/nfc_tm_activated() eliminates
the race. Saving the value is required so it can be
restored when nfc_targets_found()/nfc_tm_activated()
fails and polling needs to continue.
Acked-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In digital_in_recv_sel_res(), the code that determines
the tag type will interpret bits 7:6 (lsb being b1 as
per the Digital Specification) of a SEL RES set to 11b
as a Type 4 tag. This is okay except that the neard
will interpret the same value as an NFC-DEP device
(in src/tag.c:set_tag_type() in the neard source).
Make the digital layer's interpretation match neard's
interpretation by changing the order of the checks in
digital_in_recv_sel_res() so that a value of 11b in
bits 7:6 is interpreted as an NFC-DEP device instead
of a Type 4 tag.
Acked-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There are several instances where a pskb_copy or __pskb_copy is
immediately followed by an skb_clone.
Add a couple of new functions to allow the copy skb to be allocated
from the fclone cache and thus speed up subsequent skb_clone calls.
Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <antonio@meshcoding.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Arvid Brodin <arvid.brodin@alten.se>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds some entropy to polling cycles, choosing the next
polling rf technology randomly. This reflects the change done in the
pn533 driver, avoiding possible infinite loop for devices that export 2
targets on 2 different modulations. If the first target is not
readable, we will stay in an error loop for ever.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The error code returned by digital_in_send_cmd() was not returned by
digital_in_send_atr_req().
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
So that anyone listening on SOCKPROTO_RAW for raw frames will get all
NCI frames, in both directions. This actually implements userspace NFC
NCI sniffing.
It's now up to userspace to decode those frames.
Signed-off-by: Hiren Tandel <hirent@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This allows for a more generic NFC sniffing by using SOCKPROTO_RAW
SOCK_RAW to read RAW NFC frames. This is for sniffing anything but LLCP
(HCI, NCI, etc...).
Signed-off-by: Hiren Tandel <hirent@marvell.com>
Signed-off-by: Rahul Tank <rahult@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ATR_RES response received within Activation Parameters is already
in correct order. Reversing it fails LLCP magic number check and
so P2P functionality fails.
Signed-off-by: Hiren Tandel <hirent@marvell.com>
Signed-off-by: Rahul Tank <rahult@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to section 5.15.1.3 of the NFC Activity
Specification, multiple SENSF_REQ commands can be
received by a target before it receives an ATR_REQ
command. To handle this, add a routine that checks
whether a SENSF_REQ or ATR_REQ has been recieved.
If its a SENSF_REQ, respond appropriately and
continue waiting for a ATR_REQ. If its an ATR_REQ,
handle it as before.
CC: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The check in digital_tg_send_sensf_res() that excludes
the 'RD' field from the SENSF_RES is inverted. The 'RD'
field should be excluded when the SENSF_REQ 'RC' field
is equal to DIGITAL_SENSF_REQ_RC_NONE instead of when
its not equal. This is described in section 6.6.2.11
of the NFC Digital Specification.
CC: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixing "sparse: cast to restricted __be16" message when building with
make C=1 CF=-D__CHECK_ENDIAN__
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the ISO/IEC 14443-B protocol and Type 4B tags.
It is expected that there will be only one tag within range so the full
anticollision scheme is not implemented. Only the SENSB_REQ/SENSB_RES
and ATTRIB_REQ/ATTRIB_RES are implemented.
CC: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
load_session allows a CLF to restore the gate <-> pipe table from some
proprietary location.
The main advantage to add this function is to reduce the memory wear by
running pipe creation (and storing) only once.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Extend it up to the maximum FWI value 4949 ms defined by the
ISO14443-3 specification.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Several spots in the kernel perform a sequence like:
skb_queue_tail(&sk->s_receive_queue, skb);
sk->sk_data_ready(sk, skb->len);
But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up. So this skb->len access is potentially
to freed up memory.
Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.
And finally, no actual implementation of this callback actually uses
the length argument. And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.
So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.
Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the NFC pull request for 3.15. With this one we have:
- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
now supports those through the NFC netlink and digital APIs.
- Support for TI's trf7970a chipset. This chipset relies on the NFC
digital layer and the driver currently supports type 2, 4A and 5 tags.
- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
relies on a different firmware download protocal than the C2 one. We
now support both and use the right one depending on the version we
detect at runtime.
- Support for 4A tags from the NFC digital layer.
- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xikL
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.15: First pull request
This is the NFC pull request for 3.15. With this one we have:
- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
now supports those through the NFC netlink and digital APIs.
- Support for TI's trf7970a chipset. This chipset relies on the NFC
digital layer and the driver currently supports type 2, 4A and 5 tags.
- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
relies on a different firmware download protocal than the C2 one. We
now support both and use the right one depending on the version we
detect at runtime.
- Support for 4A tags from the NFC digital layer.
- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nfc_llcp_find_local() does not modify any list entry while iterating the list.
So use list_for_each_entry instead of list_for_each_entry_safe.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This checking is common for all caller, so move the checking to one place.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Without this test, it returns NULL if dev->n_targets is 0 anyway.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to the latest draft specification from
the NFC-V committee, ISO/IEC 15693 tags will be
referred to as "Type 5" tags and not "Type V"
tags anymore. Make the code reflect the new
terminology.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This ensures we won't add polling function to the table of polling technologies
for non-supported protocols.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
nfc_find_se() does not modify any list entry while iterating the list.
So use list_for_each_entry instead of list_for_each_entry_safe.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Calling init_completion() once is enough.
Then use reinit_completion() instead in __nci_request() and nci_spi_send().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The check should be for setup function pointer.
This patch fixes NULL pointer dereference issue for NCI
based NFC driver which doesn't define setup handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes a memory leak issue that may occur if data sending fails in
initiator mode. The data_exch structure was not released in case of
error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There was a missing break making the digital stack configured for
ISO1443 target instead of ISO15693.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When a type 4A target is activated, this change adds the ISO-DEP SoD
when sending frames and removes it when receiving responses. Chaining
is not supported so sent frames are rejected if they exceed remote FSC
bytes.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for ATS request and response handling for type 4A tag
activation.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add ISO/IEC 15693 support by having netlink push the
1-byte DSFID and 8-byte UID tag information upstream.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for ISO/IEC 15693 to the digital layer. The code
currently uses single-slot anticollision only since the digital
layer infrastructure only supports one tag per adapter (making
it pointless to do 16-slot anticollision).
The code uses two new framing types:
'NFC_DIGITAL_FRAMING_ISO15693_INVENTORY' and
'NFC_DIGITAL_FRAMING_ISO15693_TVT'. The former is used to
tell the driver to prepare for an Inventory command and the
ensuing anticollision sequence. The latter is used to tell
the driver that the anticollision sequence is over and to
prepare for non-inventory commands.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
This is a follow-up patch to f3d3342602 ("net: rework recvmsg
handler msg_name and msg_namelen logic").
DECLARE_SOCKADDR validates that the structure we use for writing the
name information to is not larger than the buffer which is reserved
for msg->msg_name (which is 128 bytes). Also use DECLARE_SOCKADDR
consistently in sendmsg code paths.
Signed-off-by: Steffen Hurrle <steffen@hurrle.net>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the correct rf tech value and crc functions in target
mode when receiving a PSL_REQ, as done when receiving an ATR_REQ.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>