There is a very old quirk for the intel E7502 E7320 and E7525 memory
controller hubs that disables usage of msi interrupts on pcie hotplug
bridges of those devices, and disables changing the affinity of irqs.
Today all we have to do to disable msi on a specific device is to set
dev->no_msi, which is much more straightforward than the previous
logic.
The re-running of this fixup after pci hotplug happens below these
devices is totally bogus. All of the state we change is pure software
state and we don't change the hardware at all. Which means hotplug on
the lower devices doesn't have a chance to change this state. So we
can safely remove the special case from the pciehp driver and the pcie
portdriver.
I suspect the special case was someone's expermental debug code that
slipped in. Certainly it isn't mentioned in commit
6fb8880a61510295aece04a542767161f624dffe aka BKrev:
41966101LJ_ogfOU0m2aE6teZfQnuQ where the code first appears.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Multiple bits might be set in the Uncorrectable Error Status
register. But aer_print_error_source() only report a error of
the lowest bit set in the error status register.
So print strings for all bits unmasked and set.
And check First Error Pointer to mark the error occured first.
This FEP is not valid when the corresponing bit of the Uncorrectable
Error Status register is not set, or unimplemented or undefined.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ERR_{,UN}CORRECTABLE_ERROR_MASK are set of error bits which linux know,
set of PCI_ERR_COR_* and PCI_ERR_UNC_* defined in linux/pci_regs.h.
This masks make aerdrv not to report errors of unknown bit, while aerdrv
have ability to report such undefined errors as "Unknown Error Bit %2d".
OTOH aerdrv_errprint does not have any check of setting in mask register.
So it could report masked wrong error by finding bit in status without
knowing that the bit is masked in the mask register.
This patch changes aerdrv to use mask state in mask register propely
instead of defined/hardcoded ERR_{,UN}CORRECTABLE_ERROR_MASK.
This change prevents aerdrv from reporting masked error, and also enable
reporting unknown errors.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The static buffer errmsg_buff[] is used only for building error
message in fixed format, and is protected by a spinlock.
This patch removes this buffer and the spinlock.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The flag AER_MULTI_ERROR_VALID_FLAG in info->flag does mean that the
root port receives multiple error messages. Error messages can be
posted from different devices, so it does not mean that each reported
device has multiple errors.
If there are multiple error devices and the root port has valid error
source ID, it would be nice to report which device is the error source
reported first.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In case of multiple errors, struct aer_err_info would be reused among
all reported devices. So the info->status should be initialized before
recycled. Otherwise error of one device might be reported as the error
of another device. Also info->flags has similar problem on reporting
TLP header.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Definitions of MASK macros in aerdrv_errprint.c are tricky and unsafe.
For example, AER_AGENT_TRANSMITTER_MASK(_sev, _stat) does work like:
static inline func(int _sev, int _stat)
{
if (_sev == AER_CORRECTABLE)
return (_stat & (PCI_ERR_COR_REP_ROLL|PCI_ERR_COR_REP_TIMER));
else
return (_stat & PCI_ERR_COR_REP_ROLL);
}
In case of else path here, for uncorrectable errors, testing bits in
_stat by PCI_ERR_COR_* does not make sense because _stat should have only
PCI_ERR_UNC_* bits originated in uncorrectable error status register.
But at this time this is safe because uncorrectable error using bit
position same to PCI_ERR_COR_REP_ROLL(= bit position 8) is not defined.
Likewise, AER_AGENT_COMPLETER_MASK is always PCI_ERR_UNC_COMP_ABORT but
it works because bit 15 of correctable error status is not defined.
It means that these MASK macros will turn to be wrong once if new error
is defined. (In fact, bit 15 of correctable is now defined in PCIe 2.1)
This patch changes these MASK macros to be more strict, not to return
PCI_ERR_COR_* bits for uncorrectable error status and vise versa.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add ids module parameter which allows specifying initial IDs for the
pci-stub driver. When built into the kernel, pci-stub is linked
before any real pci drivers and by setting up IDs from initialization
it can prevent built-in drivers from attaching to specific devices.
While at it, make pci_stub_probe() print out about devices it grabbed
to weed out "but my controller isn't being probed" bug reports.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Separate out pci_add_dynid() from store_new_id() and export it so that
in-kernel code can add PCI IDs dynamically. As the function will be
available regardless of HOTPLUG, put it and pull pci_free_dynids()
outside of CONFIG_HOTPLUG.
This will be used by pci-stub to initialize initial IDs via module
param.
While at it, remove bogus get_driver() failure check.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add support for PCI-E 5.0 GT/s in max_bus_speed and cur_bus_speed.
Reviewed-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The L0s state can be managed separately for each direction (upstream
direction and downstream direction) of the link. But in the current
implementation, those are mixed up. With this patch, L0s for each
direction are managed separately.
To maintain three states (upstream direction L0s, downstream L0s and
L1), 'aspm_support', 'aspm_enabled', 'aspm_capable', 'aspm_disable'
and 'aspm_default' fields in struct pcie_link_state are changed to
3-bit from 2-bit. The 'latency' field is separated to two 'latency_up'
and 'latency_dw' fields to maintain exit latencies for each direction
of the link. For L0, 'latency_up.l0' and 'latency_dw.l0' are used to
configure upstream direction L0s and downstream direction L0s
respectively. For L1, larger value of 'latency_up.l1' and
'latency_dw.l1' is considered as L1 exit latency.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current implementation, ASPM L0s/L1 is disabled for all links
in the hierarchy if one of the link doesn't meet latency requirement.
But we can partially enable ASPM L0s/L1 on sub-tree in the hierarchy.
This patch allows partial L0s/L1 enablement in the hierarchy. And it
also reduce the calculation cost of ASPM configuration very much.
In the previous implementation, all links were enabled with the same
state. With this patch, enabled state for each link is determined
simply as follows (the 'requested' is from policy_to_aspm_state()).
enabled = requested & (link->aspm_capable & link->aspm_disable)
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce 'aspm_capable' field to maintain the capable ASPM setting of
the link. By the 'aspm_capable', we don't need to recheck latency
every time ASPM policy is changed.
Each bit in 'aspm_capable' is associated to ASPM state (L0S/L1). The
bit is set if the associated ASPM state is supported by the link and
it satisfies the latency requirement (i.e. exit latency < endpoint
acceptable latency). The 'aspm_capable' is updated when
- an endpoint device is added (boot time or hot-plug time)
- an endpoint device is removed (hot-unplug time)
- PCI power state is changed.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce 'aspm_disable' flag to manage disabled ASPM state more
robust way.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix possible NULL dereference in pcie_aspm_exit_link_state(). This
patch also cleanup some code.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove the following check in __pcie_aspm_config_link() because it
nerver be true.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We must not clear bits in 'aspm_enabled' using 'aspm_support', or
'aspm_enabled' and 'aspm_default' might be different from the actual
state. In addtion, 'aspm_default' should be intialized even if
'aspm_support' is 0.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds the most recent additions to the list of 82576 device IDs
to the list of devices needing the SR-IOV quirk.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Background:
Graphic devices are accessed through ranges in I/O or memory space. While most
modern devices allow relocation of such ranges, some "Legacy" VGA devices
implemented on PCI will typically have the same "hard-decoded" addresses as
they did on ISA. For more details see "PCI Bus Binding to IEEE Std 1275-1994
Standard for Boot (Initialization Configuration) Firmware Revision 2.1"
Section 7, Legacy Devices.
The Resource Access Control (RAC) module inside the X server currently does
the task of arbitration when more than one legacy device co-exists on the same
machine. But the problem happens when these devices are trying to be accessed
by different userspace clients (e.g. two server in parallel). Their address
assignments conflict. Therefore an arbitration scheme _outside_ of the X
server is needed to control the sharing of these resources. This document
introduces the operation of the VGA arbiter implemented for Linux kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup based on the prototype from Matthew Milcox.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup based on the prototype from Matthew Milcox.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup based on the prototype from Matthew Milcox.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move it from the middle of the function to the end.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Unify msi_free_irqs() and msix_free_all_irqs(), and rename it to a
common void function free_msi_irqs().
And relocate the common function to where the prototype is located now.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The msi_list never have MSI-X's msi_desc while MSI is enabled,
and also it never have MSI's msi_desc while MSI-X is enabled.
This patch remove check for MSI-X entry from the pci_disable_msi(),
referring that pci_disable_msix() does not have any check for MSI
entry.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We already print it out for pci bridges, so also print it out for pci devices.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
http://bugzilla.kernel.org/show_bug.cgi?id=12542 reports that with the
quirk not applied on resume, msi stops working after resuming and mcp78s
ahci fails due to IRQ mis-delivery. Apply it on resume too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Cc: Tj <linux@tjworld.net>
Reported-by: Nicolas Derive <kalon33@ubuntu.com>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Shut off the long standing
linux/drivers/pci/search.c:144: warning: 'pci_find_device' is deprecated (declared at linux/drivers/pci/search.c:136)
linux/drivers/pci/search.c:144: warning: 'pci_find_device' is deprecated (declared at linux/drivers/pci/search.c:136)
warnings that appear on every build when CONFIG_PCI_LEGACY is enabled.
gcc warns for the use in EXPORT_SYMBOL
I moved these to a separate file and disabled the warning in the Makefile for that file.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
One more form factor for Compaq Evo D510, which needs the same quirk
as the other form factors. Apparently there's no hardware monitoring
chip on that one, but SPD EEPROMs, so it's still worth unhiding the
SMBus.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Nuzhna Pomoshch <nuzhna_pomoshch@yahoo.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some devices allow an individual function to be reset without affecting
other functions in the same device: that's what pci_reset_function does.
For devices that have this support, expose reset attribite in sysfs.
This is useful e.g. for virtualization, where a qemu userspace
process wants to reset the device when the guest is reset,
to emulate machine reboot as closely as possible.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We cannot simply call acpi_get_pci_dev() on any random ACPI handle
and hope that it works, because a PCI root bridge may not have
an associated struct pci_dev.
This is allowed per the PCI specification, and is referred to as a
non-materialized bridge.
So, depending on the type of PCI bridge that the handle points to,
use the appropriate interface to return the struct pci_bus correctly.
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
yenta needs this for example.
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This was #define'd as 0 on all platforms, so let's get rid of it.
This change makes pci_scan_slot() slightly easier to read.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
An SR-IOV capable device includes an SR-IOV PCIe capability which
describes the Virtual Function (VF) BAR requirements. A typical SR-IOV
device can support multiple VFs whose BARs must be in a contiguous region,
effectively an array of VF BARs. The BAR reports the size requirement
for a single VF. We calculate the full range needed by simply multiplying
the VF BAR size with the number of possible VFs and create a resource
spanning the full range.
This all seems sane enough except it artificially inflates the alignment
requirement for the VF BAR. The VF BAR need only be aligned to the size
of a single BAR not the contiguous range of VF BARs. This can cause us
to fail to allocate resources for the BAR despite the fact that we
actually have enough space.
This patch adds a thin PCI specific layer over the generic
resource_alignment() function which is aware of the special nature of
VF BARs and does sorting and allocation based on the smaller alignment
requirement.
I recognize that while resource_alignment is generic, it's basically a
PCI helper. An alternative to this patch is to add PCI VF BAR specific
information to struct resource. I opted for the extra layer rather than
adding such PCI specific information to struct resource. This does
have the slight downside that we don't cache the BAR size and re-read
for each alignment query (happens a small handful of times during boot
for each VF BAR).
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Yu Zhao <yu.zhao@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Without the check, the config space may be filled with zeros. Though
the driver should try to avoid call restoring before saving, but the
pci layer also should check this.
Also removes the existing check in pci_restore_standard_config, since
it's superfluous with the new check in restore_state.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: SGI hotplug: do not use hotplug_slot_attr
PCI hotplug: SGI hotplug: fix build failure
By the pci slot changes, callbacks of attributes under slot directory
(/sys/bus/pci/slots) had been changed to get the pointer to struct
pci_slot instead of struct hotplug_slot. So the path_show() that
assumes the parameter is a pointer to struct hotplug_slot seems
broken.
Tested-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The commit bd3d99c170 ("PCI: Remove
untested Electromechanical Interlock (EMI) support in pciehp."), which
removes the definition of "struct hotplug_slot_attr", broke SGI
hotplug driver. By this commit, we get the following compile error.
drivers/pci/hotplug/sgi_hotplug.c:106: error: variable 'sn_slot_path_attr' has initializer but incomplete type
drivers/pci/hotplug/sgi_hotplug.c:106: error: unknown field 'attr' specified in initializer
drivers/pci/hotplug/sgi_hotplug.c:106: error: extra brace group at end of initializer
drivers/pci/hotplug/sgi_hotplug.c:106: error: (near initialization for 'sn_slot_path_attr')
drivers/pci/hotplug/sgi_hotplug.c:106: warning: excess elements in struct initializer
drivers/pci/hotplug/sgi_hotplug.c:106: warning: (near initialization for 'sn_slot_path_attr')
drivers/pci/hotplug/sgi_hotplug.c:106: error: unknown field 'show' specified in initializer
drivers/pci/hotplug/sgi_hotplug.c:106: warning: excess elements in struct initializer
drivers/pci/hotplug/sgi_hotplug.c:106: warning: (near initialization for 'sn_slot_path_attr')
drivers/pci/hotplug/sgi_hotplug.c: In function 'sn_hp_destroy':
drivers/pci/hotplug/sgi_hotplug.c:203: error: invalid use of undefined type 'struct hotplug_slot_attribute'
drivers/pci/hotplug/sgi_hotplug.c: In function 'sn_hotplug_slot_register':
drivers/pci/hotplug/sgi_hotplug.c:655: error: invalid use of undefined type 'struct hotplug_slot_attribute'
This patch fixes this regression by adding the definition of struct
hotplug_slot_attr into sgi_hotplug.c.
Tested-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Two defects work together result in KVM device passthrough randomly can't
work:
1. iommu_snooping is not initialized to zero when vm_iommu_init() called.
So it is possible to get a random value.
2. One line added by commit 2c2e2c38("IOMMU Identity Mapping Support")
change the code path, let it bypass domain_update_iommu_cap(), as well as
missing the increment of domain iommu reference count.
The latter is also likely to cause a leak of domains on repeated VMM
assignment and deassignment.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The physical address passed to domain_pfn_mapping() should be rounded
down to the start of the MM page, not the VT-d page.
This issue causes kernel panic on PAGE_SIZE>VTD_PAGE_SIZE platforms e.g. ia64
platforms.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In domain_sg_mapping(), use aligned_nrpages() instead of hand-coded
rounding code for calculating the size of each sg elem. This means that
on IA64 we correctly round up to the MM page size, not just to the VT-d
page size.
Also remove the incorrect mm_to_dma_pfn() when intel_map_sg() calls
domain_sg_mapping() -- the 'size' variable is in VT-d pages already.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
