Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use net_device_ops for usbnet device, and export for use
by other derived drivers.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default handler for net_device_stats already does same thing.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calculate a score for each 1000 IRQs:
- TX completions are worth 1 point
- RX completions are worth 4 if merged using LRO or 2 otherwise
Reduce moderation if the score is less than 10000, down to a minimum
of 5 us. Increase moderation if the score is more than 20000, up to
the specified maximum.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bug this function works around only applies to the first set of
page-mapped registers; other pages can be written without locking.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases, reading the legacy interrupt status register can
acknowledge an event queue whose attention flag has not yet been set
in the register. Until we service this event queue it will not
generate any more interrupts. Therefore, as a secondary check, poll
the next slot in each active event queue whose flag is not set.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet parser used in the TX data path for locating checksum
fields can lose synchronisation with the TX queue manager when
handling packets that look like IPv4 but are too short (17-32 bytes).
Work around this by padding to 33 bytes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb driver was using map_single to map the skbs and then unmap_page to
unmap them. This update changes that so instead uses skb_dma_map and
skb_dma_unmap.
In addition the next_to_watch member of the buffer_info struct was being
set uneccesarily. I removed the spots where it was set without being needed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if there are no multicast addresses programmed into the PF then
the VFs cannot have their multicast filters reset. This change makes it so
the code path that updates vf multicast is always called along with the pf
updates.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb was previously setting up all of the timer members itself. It is
easier to just call setup_timer and reduce the calls to one line.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes IGB_DESC_UNUSED and replaces it with a function call
instead in order to cleanup some of the ugliness introduced by the macro.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the 82575 is fed 802.1q packets, it chokes with
an error of the form:
igb 0000:08:00.1 partial checksum but proto=81!
As the logic there was not smart enough to look into
the vlan header to pick out the encapsulated protocol.
There are times when we'd like to send these packets
out without having to configure a vlan on the interface.
Here we check for the vlan tag and allow the packet to
go out with the correct hardware checksum.
Thanks to Kand Ly <kand@riverbed.com> for discovering the
issue and the coming up with a solution. This patch is
based upon his work.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
IBM EMAC driver performs device reset (drivers/net/ibm_newemac/core.c:
emac_probe() -> emac_init_phy() -> emac_reset()) before registering
appropriate net_device (emac_probe() -> register_netdev()), so
net_device name contains raw format string during EMAC reset ("eth%d").
If the case of reset timeout, emac_report_timeout_error() function is
called to report an error. The problem is this function uses net_device
name to report device related, which is not correct, as a result in the
kernel log buffer we see:
eth%d: reset timeout
The solution is to print device_node full_name instead. After applying
the patch proposed, error string is like the following:
/plb/opb/ethernet@ef600e00: reset timeout
Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert ixgbe to use net_device_ops properly.
Rather than changing the select_queue function pointer
just check the flag.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1577ecef76 ("netdev: Merge UCC
and gianfar MDIO bus drivers") broke the TSEC TBI PHY support: the
driver now refuses to probe TBI MDIO buses as it doesn't know about
"fsl,gianfar-tbi" compatible entry, and thus _probe() fails with
-ENODEV status.
Fix this by adding "fsl,gianfar-tbi" to the list of known Gianfar
MDIO buses.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 4826857f1b ("gianfar: pass the
proper dev to DMA ops") introduced this build breakage:
CC drivers/net/gianfar.o
drivers/net/gianfar.c: In function 'gfar_suspend':
drivers/net/gianfar.c:552: error: 'struct gfar_private' has no member named 'dev'
drivers/net/gianfar.c: In function 'gfar_resume':
drivers/net/gianfar.c:601: error: 'struct gfar_private' has no member named 'dev'
make[2]: *** [drivers/net/gianfar.o] Error 1
Fix this by converting suspend and resume routines to use
gfar_private->ndev.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables support for the new Intel 82552 adapter (new PHY paired
with the existing MAC in the ICH7 chipset). No new features are added to
the driver, however there are minor changes due to updated registers and a
few workarounds for hardware errata.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When merging into Jeff's tree:
commit 5f66f20806
Author: Arthur Jones <ajones@riverbed.com>
Date: Thu Mar 19 01:13:08 2009 +0000
e1000e: allow tx of pre-formatted vlan tagged packets
We lost one line, this fixes that missing
piece...
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed duplicated #include in drivers/net/dnet.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The watchdog will schedule an interrupt to help make sure queues are
cleaned in the case when an interrupt is missed, most likely due to very
high load. On 82599, there are extra interrupt registers to account for
the larger number of MSI-X vectors (64 total for 82599 vs. 18 total for
82598). These must be taken into account when performing this operation in
the watchdog.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool isn't reporting the support level of WoL for 82599 KX4 devices.
While the device does support WoL, ethtool was never updated to properly
report the level of support, nor will it allow ethtool to modify the type
of packets to listen for.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82598's PCI bus reporting on driver load was broken after 82599 merged.
This results in incorrect reporting, and an erroneous warning message
that the 82598 is in a PCIe slot that isn't fast enough to run 10GbE.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code updates ixgb so that it can use the skb_dma_map/unmap functions
to map the buffers. In addition it also updates the tx hang logic to use
time_stamp instead of dma to determine if it has detected a tx hang.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with igb, when the e1000e driver is fed 802.1q
packets with hardware checksum on, it chokes with an
error of the form:
checksum_partial proto=81!
As the logic there was not smart enough to look into
the vlan header to pick out the encapsulated protocol.
There are times when we'd like to send these packets
out without having to configure a vlan on the interface.
Here we check for the vlan tag and allow the packet to
go out wiht the correct hardware checksum.
Thanks to Kand Ly <kand@riverbed.com> for discovering the
issue and the coming up with a solution. This patch is
based upon his work.
Fixups from Stephen Hemminger <shemminger@vyatta.com> and
Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a few issues I noticed in e1000e. These include a double free
of the skb if mapping fails, and the fact that context descriptors appear
to be left in the descriptor ring after the failure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device ID and related support for 82583 mac.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Radheka Godse <radheka.godse@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpu_to_le16 here looks suspicious to me, I don't think we need it
because put_unaligned_le16 also does this.
I don't currently have any big endian hardware with a PCI bus available
to test on, so I haven't been able to verify this.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the generic eth_mac_addr function with one that
also updates the hardware mac address registers. It also renames the
existing smsc911x_set_mac_address function to
smsc911x_hw_set_mac_address for clarity.
Newer LAN911x and all LAN921x devices also support changing the mac
address while the device is running, which is useful for some bonding
modes.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vast majority of bit constants in this driver are defined in the
header file, but TX and RX status word bits are not. This patch (which
should make no functional change) defines these, to make the driver
slightly more readable.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sungem driver only got partially converted to net_device_ops.
Since this could cause bugs, please push this to 2.6.29
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch to reconfigure vlan-ids during an i/f down/up cycle
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch to replenish the rx-queue when it is in a starved
state (due to out-of-mem conditions)
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc911x_phy_adjust_link is called periodically by the phy layer (as
it's run in polling mode), and it only updates the hardware when it sees
a change in duplex or carrier. This patch clears the last known values
every time the interface is brought up, instead of only when the module
is loaded.
Without this patch the adjust_link function never updates the hardware
after an ifconfig down; ifconfig up. On a full duplex link this causes
the tx error counter to increment, even though packets are correctly
transmitted, as the default MAC_CR register setting is for half duplex.
The tx errors are "no carrier" errors, which should be ignored in
full-duplex mode. When MAC_CR is set to "full duplex" mode they are
correctly ignored by the hardware.
Note that even with this patch the tx error counter can increment if
packets are transmitted between "ifconfig up" and the first phy poll
interval. An improved solution would use the phy interrupt with phylib,
but I haven't managed to make this work 100% robustly yet.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Address of SH_TSU_ADDR and ARSTR of SH7763 was wrong.
This revise it.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handling of IRQ of the SH7763/SH7764 CPU which sh_eth supported was
changed.
This revises it for this change.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be passing the of_platform device struct into the DMA ops as
its the one that has the archdata setup to know which low-level DMA ops we
should be using (not the net_device one). This isn't an issue until we
expect the archdata to be setup correctly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port's link is down (except to driver restart) and the port is
configured for auto sensing, we try to sense port link type (Ethernet
or InfiniBand) in order to determine how to initialize the port. If
the port type needs to be changed, all mlx4 for the device interfaces
are unregistered and then registered again with the new port
types. Sensing is done with intervals of 3 seconds.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Tulip is currently doing request_irq before it has done its
initialization. This is usually not a problem because it hasn't
enable interrupts yet, but with DEBUG_SHIRQ on, we call the irq handler
when registering the interrupt as a sanity check.
This can result in a NULL ptr dereference, so call tulip_init_ring
before request_irq, and add a free_ring function to do the freeing
now shared with tulip_close.
Tested with a shell loop running ifup, ifdown in a loop a few hundred
times with DEBUG_SHIRQ on.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Make NetworkManager work with virtio_net
For now the semantics are simple: There is always carrier.
This allows a seamless experience with e.g., qemu/kvm
where NetworkManager just configures and sets up
everything automagically.
If/when a generally agreed-upon way to control
carrier on/off in the emulator/hypervisor level
emerges, it will be trivial to extend the driver
to support that too, but for now even this 2-liner
makes user experience that much better.
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects an omission from the following commit:
commit f0c76d6177
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Wed Jul 2 18:21:58 2008 -0700
bonding: refactor mii monitor
The un-refactored code checked the link speed and duplex of
every slave on every pass; the refactored code did not do so.
The 802.3ad and balance-alb/tlb modes utilize the speed and
duplex information, and require it to be kept up to date. This patch
adds a notifier check to perform the appropriate updating when the slave
device speed changes.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary check (skb_padto does the same check)
Remove unnecessary duplicate variable
Remove unnecessary clearing of padded part of skb.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSI-X handler was chosen before the call to pci_enable_msix().
If MSI-X was not available, the wrong MSI-X handler would be used in
INTA mode. This would cause a screaming interrupt problem because
INTA would not be cleared by the MSI-X handler.
Fixed by assigning MSI-X handler after pci_enable_msix() returns
successfully. Also update version to 1.9.3.
Thomas Chenault <thomas_chenault@dell.com> helped us find this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warnings, by using integer firmware types.
drivers/net/netxen/netxen_nic_hw.c: In function 'netxen_load_firmware':
drivers/net/netxen/netxen_nic_hw.c:1146: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1146: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1146: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1159: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1159: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1159: warning: comparison with string literal results in unspecified behavior
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
user needs to see this message even if debugging disabled
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hopefully the register contents will guide us to why this failure occured
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_clear_station_table will be called every time rxon called.
In this function ucode_key_table is set to 0 even though a static
WEP security is set. This will cause in many warning and might be
an issue if dynamic WEP is set. This patch make sure we keep track
of all existing static WEP when this function is called.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During preparation of TX we create DMA mapping to TX command as part of
preparing the TFD. This mapping needs to be cleared at the time TFD is
freed.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945 uses iwl_tx_cmd_complete to reclaim the unused buffers of the queue.
iwl_tx_cmd_complete in turn call the iwl_hcmd_queue_reclaim which will
unmap the dma mapping to tx_cmd and frees the memory.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes the bug 1900 at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1900
Issues:
Throughput and success ratio calculations were not done properly.
Number of retries were exceeding 16.
Fix:
Patch fixes above issues by doing window calculations inline with iwlwifi
Patch adds sanity check to limit number of retries to 16.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_led's structure from iwlwifi.
Patch also removes CONFIG_IWL3945_LEDS flag from Kconfig as 3945's led
support will now be enabled if user selects CONFIG_IWLWIFI_LEDS.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
error is:
iwl3945-base.c:545:5: warning: symbol 'iwl3945_set_dynamic_key' was not
declared. Should it be static?
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When iwlwifi driver receive fixed rate debugfs command, validate the
antenna selection, if the selection is invalid, report the valid antenna
choice and do not set the rate scale table to fixed rate. Otherwise, set
the entire rate scale table to the fixed rate request by the user. this
validation can prevent sysassert happen in uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when perform rate scaling, in tx status function, checking for
IEEE80211_TX_STAT_AMPDU flag instead of IEEE_TX_CTL_AMPDU flag to perform
AMPDU rate scaling operation.
IEEE80211_TX_CTL_AMPDU was set by mac80211 for aggregation pkt. But when
iwlwifi receive the tx status reply, it reset the flag to following
info->flags = IEEE80211_TX_STAT_ACK;
info->flags |= IEEE80211_TX_STAT_AMPDU;
it causes the rate-scaling to not work for aggregation pkt if we checking
for IEEE80211_TX_CTL_AMPDU flag.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During rate scaling, checking for 0 retry count before decrement
the count by 1, this can avoid the retry count to become 255 (0xff),
which will cause the rate to drop faster than what we expect during good
condition (receive 0 retry packet). also change the algorithm to make
the rate not drop faster than what we like.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the MLME handshaking complete and tx aggregation started for the
tid. Do not send unnecessary turn on aggregation request to mac80211.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding more Radio information when displaying
rate_scale_table. This can help to understand how many antenna and the
current RF condition such as SISO, MIMO2, MIMO3.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when display rate_scale_table debugfs information, also display valid tx
antenna information, this will help user to select correct antenna when
issue fixed rate debugfs command
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before: 1099 errors, 93 warnings, 2854 lines checked
After: 19 errors, 47 warnings, 2976 lines checked
The big bulk of this is code indent and over 80 character lines
(Lindent did this part) Other changes are foo * bar spacing, and
trailing whitespace.
v2: Cleans up ill-indented comments. Subsequently, this reduces the
number of warnings, too. Thanks to Joe Perches for pointing this out!
v3: Ran the whole file through Lindent first... which does most of
the work for me. :) Again, thanks to Joe Perches for this.
This is my final answer!
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a driver for Marvell 88w8xxx TOPDOG PCI/PCIe wireless parts.
This initial version supports the 88w8687 802.11b/g PCIe part on
channels 1-11, and only STA mode is currently implemented.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must not disable ACK sending in this case since it would break
normal station operations. In addition, clarify the comment about AP
mode to make more sense.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the sparse complaints:
drivers/net/wireless/ath9k/eeprom.c:1407:5: warning: symbol
'ath9k_hw_4k_get_spur_channel' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:1436:19: warning: symbol
'eep_4k_ops' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2808:5: warning: symbol
'ath9k_hw_def_get_spur_channel' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2837:19: warning: symbol
'eep_def_ops' was not declared. Should it be static?
CC [M] drivers/net/wireless/ath9k/eeprom.o
CHECK drivers/net/wireless/ath9k/mac.c
CC [M] drivers/net/wireless/ath9k/mac.o
CHECK drivers/net/wireless/ath9k/calib.c
drivers/net/wireless/ath9k/calib.c:883:6: warning: symbol 'ar9285_clc'
was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not a fatal message, hitting it simply means we're
going to tell the upper layers to slow their horses down but
as we make more descriptors available we let the show continue
by waking up the queues in ath_wake_mac80211_queue().
We downgrade this as otherwise we fill up your kernel log with
messages which can be common under heavy traffic.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a module parameter for mac80211_hwsim regulatory testing.
This module parameter is designed specifically to help test the
different possible types of driver specific regulatory requests
and also helps to test world roaming, all without any hardware.
If you want to just simply test different alpha2s just use the userspace
regulatory request as this won't buy you anything new.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this so we can later inform userspace who set the
regulatory domain and provide details of the request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used as we can always just assume the first
regulatory domain set will _always_ be a static regulatory
domain. REGDOM_SET_BY_CORE will be the first request from
cfg80211 for a regdomain and that then populates the first
regulatory request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before: 881 errors, 265 warnings, 4507 lines checked
After: 114 errors, 273 warnings, 4548 lines checked
This was mostly "space required after that ',' (ctx:VxV)".
Also a fair number of whitespace, code indent, and C99 comment cleanups.
New warnings introduced are all "line over 80 character"
md5sums are identical, as I skipped any fixes which may have altered the resulting binary.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate table would not have been chosen before the interface
has been brought up. Reading 'rcstat' in this case would result
in an oops, fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 expects the driver to fill in the starting
sequence number of an ADDBA request to initiate TX aggregation.
IEEE80211_TX_CTL_AMPDU would be set for frames only after a
successful ADDBA exchange, but we have to increment the
internal sequence counter for the normal(non-AMPDU) data frames proerly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI was not being initialized correctly for all HW variants.
This patch fixes it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for Acer Ferrari 5000, and also specifies
the subsystem device ids for previously reported e-machines e510 and
Acer Aspire One A150.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put the device id-to-gpio mapping in a table to make it easier to add
new devices. The list of supported devices is unchanged.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move LED code out of base.c for clarity.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not touch mac parameter passed to ath5k_eeprom_read_mac unless
we are sure we have correct address. I.e. when returning error, do
not change it.
While at it, use '= {}' compiler trick for memsetting mac_d.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make some structures const to place them in .rodata, since we won't
change them.
Most important parts of objdump -h:
- 0 .text 00011170
+ 0 .text 00011140
- 5 .rodata 0000828e
+ 5 .rodata 0000895e
- 13 .data 00000560
+ 13 .data 00000110
- 14 .devinit.data 00000260
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
device name was changed from 100 to 1000
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add check for new association to ease reading.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Passing frames with a bad FCS to the user is an optional feature.
However it doesn't work reliable and strangely not in the native monitor mode?!
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hopefully nothing controversial here, since the driver hasn't been touched in a while!
Before: 36 errors, 6 warnings, 482 lines checked
After: 0 errors, 3 warnings, 485 lines checked
This was nearly all trailing whitespace, * and parenthesis spacing, and code indent changes.
md5sum of object file before and after are identical.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch improves range and connection stability in AR9285.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove obsolete enums from ipw2x00/ieee80211.h, they are not used anymore.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use IE definitions from linux/ieee80211.h and drop the appropriate enum
from ipw2x00/ieee80211.h
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove several duplicated defines from ipw2x00/ieee80211.h which are
also available in linux/ieee80211.h.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace all remaining occurrences of CONFIG_IEEE80211_DEBUG with
CONFIG_LIBIPW_DEBUG in libipw to allow debug output again.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_radio_{en,dis}able is only compiled if RFKILL is enabled, but it is
required by the 'ath9k_wiphy_select' function.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath9k/debug.c: In function 'read_file_wiphy':
drivers/net/wireless/ath9k/debug.c:377: error: implicit declaration of
function 'put_unaligned_le32'
drivers/net/wireless/ath9k/debug.c:378: error: implicit declaration of
function 'put_unaligned_le16'
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath9k/ahb.c: In function 'ath_ahb_probe':
drivers/net/wireless/ath9k/ahb.c:136: error: 'aphy' undeclared (first
use in this function)
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current macro is wrong, because detects some AR5416 devices as an
AR9100 device. The AR5416 devices would have performance issues after
this change, because the contents of the ar5416 specific and of the
ar9100 specificinitval arrays are swapped. Fortunately we can correct
this with the rename of the arrays simply.
Changes-licesed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All other version checking macros are in a common location within the
reg.h file. The AR_SREV_9100_OR_LATER macro is wrong currently, but will
be fixed with the next patch.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we have two different versions of this macros. Because they
would have to do the same thing, we should simplify and merge them.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix AR9285 1.1 and 1.2 version check macro.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the initvalues for AR9285 chipset and also adds
periodic PA offset caliberation.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
accessing RXBUF list in ath_rx_cleanup may cause panic if
ath_descdma_setup fails even before RXBUF list is initialized.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can sleep for memory during init time and so allocating rx buffers,
descriptro buffers with GFP_KERNEL should help us to get rid of transient
alloc fails.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ACME Inc. is now selling a dual band radio.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables power save support on all p54 devices.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds SoftLED support for all p54 devices.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disabling the receiver logic with P54_FILTER_TYPE_RX_DISABLED is not
supported by all firmwares. However we have an alternative: hibernation.
And the only side effect - so far - is a bit less power consumption. WIN!
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces most printk(KERN_* "") with their by dev_* analogue.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All three drivers (p54pci, p54usb and p54spi) are implementing the
same functionality three times. So, why not put it into the shared library?!
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes a problem when the (Soft)LED stayed on after the module was unloaded.
It turned out that the USB core disables all endpoints before calling the disconnect method.
So it was impossible to switch off the radio & LEDs.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver are trying to create an 'ath9k' directory in debugfs for each
device currently. If there are more than one device in the system, the
second try will always fail.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently part of support for FW caching is unconditionally compiled
in even if it is never used. Consistently remove caching support if
not requested by user.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd_op_tx() must not return an arbitrary error value since that can
leave mac80211 trying to retransmit the frame and with the extra data
pushed into the beginning of the skb on every attempt, this will end up
causing a kernel panic (skb_under_panic from skb_push call). This can
happen, e.g., when ejecting the device when associated.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All 802.11n PCI devices (Cardbus, PCI, mini-PCI) require
serialization of IO when on non-uniprocessor systems. PCI
express devices not not require this.
This should fix our only last standing open ath9k kernel.org
bugzilla bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=12110
A port is probably required to older kernels and I can work on
that.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most fasync implementations do something like:
return fasync_helper(...);
But fasync_helper() will return a positive value at times - a feature used
in at least one place. Thus, a number of other drivers do:
err = fasync_helper(...);
if (err < 0)
return err;
return 0;
In the interests of consistency and more concise code, it makes sense to
map positive return values onto zero where ->fasync() is called.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
It fails on the following systems:
- RTL8169sc/8110sc (XID 18000000)
reported by Tim Durack <tdurack@gmail.com> (x86)
- RTL8169sb/8110sb (XID 10000000)
reported by Mikael Pettersson <mikpe@it.uu.se> (ARM)
The patch appeared to work on x86 for the following systems:
RTL8169sb/8110sb 10000000 PCI (EXT)
RTL8110s 04000000 PCI (EXT)
RTL8102e 24a00000 PCI-E (LOM)
RTL8168c/8111c 3c2000c0 PCI-E (LOM)
RTL8168b/8111b 38000000 PCI-E (LOM)
RTL8168b/8111b 38000000 PCI-E (EXT)
The patch exposes two problems:
1) while not completely wrong, mac addresses are not read correctly
from the EEPROM
2) the MAC address registers are not correctly set
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
It shortens the code and fixes the current pci_unmap leak with
padded skb reported by Dave Jones.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L0s workaround should be moved into a pci quirk and so it is not
necessary in the driver. This update removes the L0s workaround from the
igb driver.
This was the second half of the PCI quirk patch that Matthew Wilcox did
not pick up when he picked up the quirk patch.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To mark all features and bugfixes submitted since 4.0.11.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the load balancing capability of firmware
and hardware to spray traffic into different cpus through
separate rx msix interrupts.
The feature is being enabled for NX3031, NX2031 (old) will be
enabled later. This depends on msi-x and compatibility with
msi and legacy is maintained by enabling single rx ring.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o remove max_ prefix from ring sizes, since they don't really
represent max possible sizes.
o cleanup naming of rx ring types (normal, jumbo, lro).
o simplify logic to choose rx ring size, gig ports get half
rx ring of 10 gig ports.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detach network interface on PCI suspend and recreate hardware
context after resumes.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup a bit of whitespace, add some function header comments, and fix a
few comments around the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx DMA unit should be disabled when bringing the device down. Also,
the KX4 device with 82599 supports WoL, so we should clear the Wake Up
Status (WUS) after a PCIe slot reset.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are possible times that a driver may fail to completely initialize,
due to a buggy platform or a buggy kernel. In those cases, we'd rather
fail gracefully instead of a panic. Add a few safety checks to some
critical paths to try and prevent a panic in these corner-case situations.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleans up the following pieces of the Rx initialization path:
- Enable the ECC memory fault interrupt in OTHER causes.
- Fix an 82598 initialization of RDRXCTL when depending on RSS and VMDq to
be enabled. We don't need these features enabled to safely set the MVMEN
bit to allow multiple SRRCTL register mappings into the RXDCTL registers.
- Fix the RSS initialization path to not stomp on DCB accidentally. When
configuring the MRQC (multiple Rx queue contol) register, we want to make
sure we only OR in features as necessary, instead of full assignment.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx accounting when cleaning during NAPI was not completely properly.
We should use the work_limit to determine when to finish cleaning, and
use the same to return the cleaned status. The impact of running like this
causes the NAPI clean for this Tx to get stuck in a scheduling loop, and
can result in Tx not getting cleaned, ending with a Tx hang and device
reset.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionally if the driver was loaded in a system that
didn't support MSI-X or MSI and was on a shared interrupt,
the driver would then panic in NAPI on the first shared
interrupt because we hadn't called napi_add yet.
Solution: call napi_add before calling request_irq
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt models using EITR have changed in 82599. The way the register
is laid out, the change is transparent to some of the existing code.
However, some of it isn't. This patch fixes all the cases where EITR
handling is different than 82598.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 mistakenly enabled drop on Rx queues in the packet buffer. The
default mode should be store-and-forward from the FIFO.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_no_dma_resources counter reported by ethtool -S ethX is not
counting correctly. In 82599, the queue mappings for the counters need
to be mapped properly, and accounted for properly.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A purely cosmetic change. Report which physical layer is present, instead
of PHY unknown. 82599 added new PHY types for the SFP+ devices, and this
was missed getting updated.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 82576 copper adapter and necessary code to restrict wol for
quad port adapter to first port.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding device id to support 82576NS dual port copper
NIC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a typo that was doing a less than comparison instead of
a left shift due to the fact that I didn't get enough <'s in there.
This resolves an issue in which vlans were not functioning correctly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Pf to pool if adding a VLVF register value and the VFTA bit is
already set.
This patch addresses the unlikely situation that the PF adds a vlan
entry when the vlvf is full, and a vf later adds the vlan to the vlvf.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to support wol on the second port for situations such as when the
lan ports are on the motherboard itself.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If DCA is undefined then the adapter struct becomes unnecessary. To
resolve this issue the DCA calls can simply make a call to the adapter
struct through the rx_ring adapter struct member.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_running check in igb poll is a hold over from the use of fake
netdevs to use multiple queues with NAPI prior to 2.6.24. It is no longer
necessary to have the call there and it currently can cause errors if
work_done == budget.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the new DCA API, the driver should use dca3_get_tag() instead of
the obsolete dca_get_tag().
Signed-off-by: Maciej Sosnowski < maciej.sosnowski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove flash size check which made sense only for ancient
boards with 1MB flash. The check is based on values read
from specific locations and fails with firmware size changes.
This prevents driver from getting right mac addresses.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found the PPP subsystem to not work properly when connecting channels
with different speeds to the same bundle.
Problem Description:
As the "ppp_mp_explode" function fragments the sk_buff buffer evenly
among the PPP channels that are connected to a certain PPP unit to
make up a bundle, if we are transmitting using an upper layer protocol
that requires an Ack before sending the next packet (like TCP/IP for
example), we will have a bandwidth bottleneck on the slowest channel
of the bundle.
Let's clarify by an example. Let's consider a scenario where we have
two PPP links making up a bundle: a slow link (10KB/sec) and a fast
link (1000KB/sec) working at the best (full bandwidth). On the top we
have a TCP/IP stack sending a 1000 Bytes sk_buff buffer down to the
PPP subsystem. The "ppp_mp_explode" function will divide the buffer in
two fragments of 500B each (we are neglecting all the headers, crc,
flags etc?.). Before the TCP/IP stack sends out the next buffer, it
will have to wait for the ACK response from the remote peer, so it
will have to wait for both fragments to have been sent over the two
PPP links, received by the remote peer and reconstructed. The
resulting behaviour is that, rather than having a bundle working
@1010KB/sec (the sum of the channels bandwidths), we'll have a bundle
working @20KB/sec (the double of the slowest channels bandwidth).
Problem Solution:
The problem has been solved by redesigning the "ppp_mp_explode"
function in such a way to make it split the sk_buff buffer according
to the speeds of the underlying PPP channels (the speeds of the serial
interfaces respectively attached to the PPP channels). Referring to
the above example, the redesigned "ppp_mp_explode" function will now
divide the 1000 Bytes buffer into two fragments whose sizes are set
according to the speeds of the channels where they are going to be
sent on (e.g . 10 Byets on 10KB/sec channel and 990 Bytes on
1000KB/sec channel). The reworked function grants the same
performances of the original one in optimal working conditions (i.e. a
bundle made up of PPP links all working at the same speed), while
greatly improving performances on the bundles made up of channels
working at different speeds.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mv643xx_eth_open() is called to up an interface, port_start()
will first re-program the unicast address filter, and then
re-initialise the PORT_CONFIG register, but that will disable unicast
promiscuous mode if it was enabled by the unicast address filter setup.
This isn't a problem on ifconfig up, as ->set_rx_mode() will be called
shortly afterwards which will program the filters again, but it does
trigger when changing the MTU, which calls mv643xx_eth_stop() and then
mv643xx_eth_open() by hand to repopulate the receive rings with skbuffs
of the new size.
Swap the initialisation of the PORT_START register and the call to
the unicast filter setup function to fix this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original patch was submitted last year but wasn't discussed or applied
because of missing maintainer's CCs. I only fixed some formatting errors,
but as I saw tulip is very badly formatted and needs further work.
Original description:
This patch fixes MTU problem, which occurs when using 802.1q VLANs. We
should allow receiving frames of up to 1518 bytes in length, instead of
1514.
Based on patch written by Ben McKeegan for 2.4.x kernels. It is archived
at http://www.candelatech.com/~greear/vlan/howto.html#tulip
I've adjusted a few things to make it apply on 2.6.x kernels.
Tested on D-Link DFE-570TX quad-fastethernet card.
Signed-off-by: Tomasz Lemiech <szpajder@staszic.waw.pl>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It closes a race in phy_stop_machine when reprogramming of phy_timer
(from phy_state_machine) happens between del_timer_sync and cancel_work_sync.
Without this change it could lead to crash if phy_device would be freed after
phy_stop_machine (timer would fire and schedule freed work).
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the circular locking problem by changing the locking strategy
concerning the logging of firmware handles.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC variant in the 405EX and 405EXr chips needs the "440EP" type clock
control workaround to avoid lockups of the Rx side during reset.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple unicast address support appears to have been broken with the
change to support net_device_ops. This a regression from 2.6.28 to 2.6.29.
I'm not 100% on whether ndo_set_multicast_list can be NULL after this
or not. If ndo_set_rx_mode is set everything _should_ be using it.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Dave Jones <davej@redhat.com>
The dma-debug changes caught that this driver uses the
wrong DMA mapping length when skb_padto() does something.
With suggestions from Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the mac address when a macvlan device is up will leave the
device on the wrong hash chain making it impossible to receive
packets.
There is no checking of the mac address set on the macvlan. Allowing
a misconfiguration to grab packets from the the underlying device or
another macvlan.
To resolve these problems I update the hash table of macvlans when the
mac address of a macvlan changes, and when updating the hash table
I verify that the new mac address is usable.
The result is well defined and predictable if not perfect handling of
mac vlan mac addresses.
To keep the code clear I have created a set of hash table maintenance
in macvlan so I am not open coding the hash function and the logic
needed to update the hash table all over the place.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in a network namespace whose only link to
the outside world is a macvlan device, not being
able to create another macvlan is a real pain.
So modify macvlan creation to allow automatically forward
a creation of a macvlan on a macvlan to become a creation
of a macvlan on the underlying network device.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reclaim 8 upper bits of netdev->features from GSO.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch from Juha Leppanen suppresses a false warning if the eeprom
load succeeds on the very last attempt.
Juha> In function smsc911x_open smsc911x_reg_read+udelay can be run 50
Juha> times with timeout reaching -1, and the following if statetement
Juha> does not catch the timeout and no warning is issued. Also if the
Juha> 50th smsc911x_reg_read is GOOD, loop is exited with timeout as 0
Juha> and bogus warning issued. Replace testing order and --timeout
Juha> instead of timeout-- and now max 50 smsc911x_reg_read's are done,
Juha> with max 49 udelays.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch from Juha Leppanen suppresses a false warning if a fast
forward operation succeeds on the very last attempt.
Juha> If smsc911x_reg_read loop is executed 500 times, timeout reaches 0
Juha> and the 500th smsc911x_reg_read result in val is ignored. If
Juha> testing order is changed, then val is checked first. The 500th
Juha> reg_read might be GOOD, why ignore it!
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1577ecef76
Author: Andy Fleming <afleming@freescale.com>
Date: Wed Feb 4 16:42:12 2009 -0800
netdev: Merge UCC and gianfar MDIO bus drivers
left out the deletion of gianfar_mii.c.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar patch as for 8139cp posted yesterday, so the same comment:
So far there was not a chance to set a mac address on running 8139too device.
This is for example needed when you want to use this NIC as a bonding slave in
bonding device in mode balance-alb. This simple patch allows it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far there was not a chance to set a mac address on running 8139cp device.
This is for example needed when you want to use this NIC as a bonding slave in
bonding device in mode balance-alb. This simple patch allows it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently ignores the local or remote link faults
raised at the mac layer. This patch fixes it.
Our mac however only advertizes link events, so wait for the
phy to stabilize the link, then enable mac link events interrupts.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the heurstics workaround unlocking a hung mac:
- reduce Tx mac toggling by enabling Tx drain before resetting the mac
- Take Tx (lack of) activity in account only
- Update the monitoring counter range to 64 bits
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under RX pressure, The HW might generate a high load of interrupts
to signal mac fifo or free lists overflow.
Disable the interrupts, and poll the relevant status bits
to maintain stats.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate TX and RX reclaim handlers
Don't disable interrupts in RX reclaim handler.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Elmininate a cache miss when accessing the CPL header within
the first aggregated buffer.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update skb truesize correctly for the 2nd buffer from a Jumbo frame
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Release page chunk reference in case we fail to map it.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ring free lists door bell less frequently,
specifically every quarter of the active FL
size.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With some asic configurations xmit of frames smaller than 60 bytes may
fail.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving netif_napi_del() up the call chain so it will get called from all
exit points.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*netif_rx_* functions is obsolete and removed in newer kernels so
we need to use corresponding *napi_* functions instead.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver for Dave DNET ethernet controller found on Dave/DENX QongEVB-LITE
FPGA. Heavily based on Dave sources, I've just adopted it to current
kernel version and done some code cleanup.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix printk format warnings:
drivers/net/wimax/i2400m/netdev.c:523: warning: format '%zu' expects type 'size_t', but argument 7 has type 'unsigned int'
drivers/net/wimax/i2400m/netdev.c:548: warning: format '%zu' expects type 'size_t', but argument 7 has type 'unsigned int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same operation is performed when the Ethernet driver initializes
the port.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch clears the irqstatus register with the exact same events it
has read from it. Since the read-write operation is not atomic, a new
irqstatus bit could have been set in between these operations and would
then be cleared accidentally.
Secondly, we now don't need any spin lock protection when
scheduling/completing napi poll as the isr will not execute anymore (as
we turn off all interrupts now).
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the throughput mode poll settings to reduce the
number of interrupts. This is only used by older hardware that need a
timer irq in throughput mode.
Secondly, this patch increases the default rx ring from 128 to 512. This
drastically improves bandwidth utilization for small packets sizes i.e
512 bytes.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the logic to moderate the interrupts by changing the
mode between throughput and poll. If there has been a large amount of
time without any burst of network load, the code will transition to pure
throughput mode (where each tx/rx/other will cause an interrupt). If
bursts of network load occurs, it will transition to poll based mode to
help reduce cpu utilization (it will not interrupt on each packet) while
maintaining the optimum network bandwidth utilization.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is only a subset of changes so that it is easier to see the
modifications. This patch removes the isr 'for' loop and shifts all the
logic to account for new tab spacing.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new optimization mode called Dynamic has been added. This will be mode
where interrupt moderation logic will dynamically switch between pure
throughput mode and poll based (called 'cpu') mode.
Also, for newer chipsets, the timer irq is not needed for throughput
mode. Secondly, since we are modifying the irqmask to change between
modes, msix is not supported.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The napi poll routine has been modified to handle all interrupt events
and process them accordingly. Therefore, the ISR will now only schedule
the napi poll and disable all interrupts instead of just disabling rx
interrupt.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two tx_done routines to handle tx completion processing. Both
these functions now take in a limit value and return the amount of tx
completions. This will be used by a future patch to determine the total
amount of work done.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unnecessary overhead code. Firstly, there is no nead
to mask off unwanted interrupts as we will be checking against the
irqmask field anyways. Secondly, there has been no value in last few
years from detecting error or unknown interrupts.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will save the irq events in the driver's context so that the
napi routine knows which interrupts have occurred. Subsequent changes
will be moving all interrupt processing into the napi poll routine.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes support for msix running in conjunction with napi.
There has been reported issues regarding the behaviour of irqmask and
generation of interrupts by the HW when in MSIX mode. When running napi,
the driver is constantly turning off/on the irqmask. For the time being,
I am going to disable it until I can root cause the issue.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing napi enable/disable calls.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer versions of the stats feature would not encompass all older
versions. This would result in only retreiving a subset of all available
stats in HW.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocols that use packet_type can be __read_mostly section for better
locality. Elminate any unnecessary initializations of NULL.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove huge board config structure from each instance, read
only necessary fields from flash.
Replace board_type with port_type (1G/10G), there's another
board_type field describing card type (SFP/XFP/CX4).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAX_RCV_CTX was set to 1, there's only rx context per
PCI function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rearrange open and close into hardware attach(), detach() and
nic up() and down(). this will be used for suspend/resume
subsequently.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o remove unused rx fragment handling code.
o imporove check for status descriptor ownership.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a bug, which occasionally caused failure in PRAM initialization after
the cold boot.
Also incremented version number to 1.45.27.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a proper cast to the argument of PAGE_ALIGN macro so that the output
won't depend on its original type. Without this cast aligned value will be
truncated to the size of the argument type.
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Tested-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sge_buff_size may not be more than 0xffff.
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Tested-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was introduced in an earlier net-next patch.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With some asic configurations xmit of frames smaller than 60 bytes may
fail.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving netif_napi_del() up the call chain so it will get called from all
exit points.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The completion interrupt disable routine is only called from the ISR, so
there is no need for irqsave/restore.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of extraneous ql_cycle_adapter. It's only called from the one
place.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remaining registers are separated into:
- <mach/regs-ost.h>
- <mach/regs-rtc.h>
- <mach/regs-intc.h>
and then we can remove pxa-regs.h completely. Instead of #include this
file, let's:
1. include the specific <mach/regs-*.h> with care (if that's absolutely
necessary)
2. define the registers in the driver, make cleanly defined API to expose
the register access to external with sufficient reason
Signed-off-by: Eric Miao <eric.miao@marvell.com>
pxa-regs.h and hardware.h are not intended for use directly in driver
code, remove those unnecessary references.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch fixes a number of race conditions in the driver.
Up until now, "entry" pointer was initialized before acquiring the right lock.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes compilation, if the PCI core is disabled.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs ath9k/phy#/wiphy can be used to show the current list of
virtual wiphys and to add/remove virtual wiphys. Eventually, this
interface could be replaced with a cfg80211/nl80211 command that is
passed through mac80211.
For example:
# cat /debug/ath9k/phy0/wiphy
primary: phy0
# echo add > /debug/ath9k/phy0/wiphy
# cat /debug/ath9k/phy0/wiphy
primary: phy0
secondary: phy1
# echo del=phy1 > /debug/ath9k/phy0/wiphy
# cat /debug/ath9k/phy0/wiphy
primary: phy0
In addition, following commands can be used to test pausing and
unpausing of the virtual wiphys:
pause=phy1
unpause=phy1
select=phy1
(select pauses and unpauses wiphys automatically based on channel)
schedule=500
(set wiphy scheduling interval in msec; 0 = disable; default value: 500)
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a very simple scheduler that goes through the wiphys and
schedules one at a time every N milliseconds (current default value:
500 ms). This is enough for initial testing, but there are number of
areas where a more complex scheduler can improve operations greatly.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow mac80211-controlled channel changes on an active wiphy and
especially during a scan. We need this as long as the scan is
controlled by mac80211. Moving this control into the driver could
allow some optimizations on scanning while using multiple virtual
interfaces, but for now, try to work as well as possible with the
current scan mechanism.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like channel change may fail in some cases and end up leaving
the hardware in state where it cannot transmit any frames. Add a
workaround to recover from this state if we detect that wiphy
selection is failing due to wiphys not leaving PAUSING state.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 should not be requesting us to transmit frames on paused
wiphys since we stop the TX queues. Just in case, add debug code to
make sure we catch if this were to happen.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For now, allow channel changes immediately and just force the other
virtual wiphys to paused state. This is needed to allow
mac80211-controlled scan to control channel changes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Notify the AP that we may be sleeping longer to allow the AP power
save code to buffer larger number of frames for us when using virtual
wiphys.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of always going through initialization/deinitialization steps,
do this only for the first/last wiphy to not break the other wiphys.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_wiphy_select() can be used to select a virtual wiphy to be
activated. Other virtual wiphys will be paused and once that is done,
the operational channel is changed and the wiphys that are on the
selected channel will be unpaused.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow virtual wiphys to be paused/unpaused to allow off-channel
operations. Pause will stop all TX queues for the wiphy and move the
STA into power save mode if in managed mode. Unpause wakes up the TX
queues and notifies the AP that the STA woke up if in managed mode.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow RX filter to pass through all broadcast/multicast frames (i.e.,
no BSSID filtering) if virtual interfaces are used. Software filtering
will be used in this case to drop broadcast/multicast frames for
foreign BSSIDs.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new struct ath_softc::sec_wiphy array is used to store information
about virtual wiphys and select which wiphy is used in calls to
mac80211. Each virtual wiphy will be assigned a different MAC address
based on the virtual wiphy index.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the initial step in allowing ath9k to register multiple
virtual radios (wiphys). The goal of virtual radios is to allow the
same radio to be shared for multiple virtual interfaces that may
operate on different channels. The mac80211 virtual interface support
is designed only for single channel operation and as such, it is not
suitable for this type of use. Anyway, it can be used on top of the
virtual radio concept, if desired (e.g., use two virtual radios to
handle two channels and then add multiple mac80211 virtual interfaces
on top of each virtual radio).
The new struct ath_wiphy is now registered as the driver data
structure for wiphy. This structure has a pointer to the shared (among
virtual wiphys of the same physical radio) struct ath_softc data. The
primary wiphy maintains the allocated memory for ath_softc. Secondary
(virtual) wiphys will only allocate the new ath_wiphy structure.
Registration of secondary wiphys is added in a separate patch.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a hardcoded BSSID mask (mask for own addresses),
iterate through all active interfaces and determine the minimal mask
that covers all local addresses.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace the internal sc_vaps array and index values by using vif
pointer from mac80211. Allow multiple VIPs to be registered. Though,
number of beaconing VIFs is still limited by ATH_BCBUF (currently
1). Multiple virtual STAs support is not yet complete, but at least
the data structures should now be able to handle this.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By exporting the register base, and word size to userspace
through debugfs it will be easier to create scripts which
parse the register information. This makes debugging and
register dumps information easier.
This will break my previous scripts which dumped and parsed
all information, but since this is only for debugging purposes
this change should not be a problem.
Dumpfiles created with the old version can be easily manually
edited to make them compatible with this new approach, which
means there will be no problems comparing dumps from the
different versions either.
Also be more consistent with using tabs to seperate different
fields.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to use ath_keyset() wrapper for
ath9k_hw_set_keycache_entry() calls. In addition, improve the comments
describing the key setting operations.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current bitmask is invalid, because the tx dma size is a 3 bit wide
value.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't store the beacon timestamp internally, nor
do we do any TIM handling in ath9k.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TSF has to be reset only once, upon bringing
the interface up in AP mode. For any beacon reconfigure calls
after that, resetting the TSF results in incorrect beacon generation.
The only exception is a change in the beacon interval,
which is indicated to the driver by mac80211 through
IEEE80211_CONF_CHANGE_BEACON_INTERVAL, handle this properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the code easier to understand.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never use SC_OP_NO_RESET, it is not configurable at all.
Remove all code that deals with this flag and make beacon
stuck processing simple.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove useless comments, fix indentation.
Also, remove all occurrences of ASSERT(vif) which are not needed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only use case for this right now is ANI calibration,
but more might come up in the future.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old code doesn't work correctly e.g. on newer chipsets like AR5418+AR2122 and AR5416+AR2133.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old code doesn't work correctly e.g. on newer chipsets like AR5418+AR2122 and AR5416+AR2133.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the RX handler to pass more status flags to mac80211.
It also changes part of the drop policy, if bad frames were requested. (Note that
currently mac80211 will throw a WARN_ON in that case. But nothing bad will happen).
This also removes some obsolete unused timestamping code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So that a new created IBSS network
doesn't break on the first scan.
It seems to Sujith and me that this
stupid code unnecessary, too.
So remove it...
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restore network sleep mode in isr if power save is enabled.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This callback can be used to handle dynamic 20/40,
and changes in the operating channel's HT parameters.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used anywhere in ath9k and is just making the code more
confusing.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are number of small details about the keycache operations that
are very easy to miss (and forget), so better include detailed
comments in ath9k_hw_set_keycache_entry() to avoid having to figure
out this every time when having to touch this area.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce stack memory footprint of iwlwifi.
(From >1000 bytes for each *_table_read
on i386 down to 32)
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Software antenna tuning is broken because of an function
ordering problem during rt2x00link_tuner().
rt2x00link_precalculate_signal()
rt2x00leds_led_quality()
rt2x00lib_antenna_diversity()
rt2x00link_precalculate_signal() will reset the quality TX/RX counters,
however rt2x00lib_antenna_diversity() requires the RX counter to
see what RSSI value must be used for a particular antenna.
We can't change the ordering since rt2x00lib_antenna_diversity() might
reset other statistics which are needed by the function called earlier.
Move the reset of the quality TX/RX counters into a seperate function
and move the call to after rt2x00lib_antenna_diversity().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can use iwl_activate_qos instead of iwl3945_activate_qos.
Patch does two things
1) Patch adds iwl_activate_qos in core library.
2) 3945 makes use of iwl_activate_qos.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch does following,
1) mac80211's shared data is now initialized in iwl3945_setup_mac.
2) Set the rfkill to right state after initialization
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for iwlagn:
- Have to free eeprom of version check fails - otherwise we end up with
memory leak.
- Include removal of workqueue (created in _setup_deferred_work) in error
handling.
for iwl3945:
- Fix a few places to jump to correct error handling.
- Reorganize error handling to match with code flow.
- Include iwl_free_channel_map as part of error handling.
- Include releasing eeprom as part of error handling.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
unify the set key flow with iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In IBSS, TSF maintains local clock counters at each station. Network
Synchronization follows a completely distributed scheme where beacon frames
are generated. Each station maintain its own TSF timestamp, extracted from
beacon timestamps they recieved. Following patch synchronize this beacon timestamp
with uCode.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
update API to support new numbering that is used for other newer devices.
5150 ucode has not been released yet, so the first released API will be v2.
For those who do have a v1 API the driver does have backward compatibility
support new value of REPLY_TX_POWER_DBM_CMD
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure we print out a warning when the index is out of bounds,
i.e. even on hw_rix == AR5K_MAX_RATES.
Also change to WARN and print text with the reported hw_rix.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect Michael MIC key (RX, should have been TX) was set for the
group key in AP mode. This resulted in all broadcast frames triggering
Michael MIC errors and eventual TKIP countermeasures. The change here
sets the correct Michael MIC key based on whether the local end is the
authenticator (well, AP for now).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Tested-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Applying kernel janitors todos (reduce stack
footprint where possible) to airo wireless driver.
(Before 1124 bytes on i386, now 876)
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
spin can reach -1 after the loop, so 0 is still success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements get_tsf() of ieee80211_ops in the zd1211rw driver.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nohwcrypt=1 module parameter can now be used to disable hardware
crypto in ath9k. While the hardware acceleration handles most cases,
it may be useful to be able to force mac80211 software implementation
to be used for some tests, e.g., with virtual interface combinations
that may not yet be supported in the key cache configuration. In
addition, this allows management frame protection to be tested with
older hardware revisions.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both the agn and 3945 drivers has some problems with dealing with
errors in their probe functions. Ensure that a goto will undo only
things that was done before the goto was called.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add more usb_dev to rt73usb.c . IDs 'stolen' from the
windows inf file(10/21/2008, 1.03.02.0000) plus some
from the Ralink linux driver(2009_0206_RT73_Linux_STA_Drv1.1.0.2.tar.bz2)
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add more usb_dev to rt2500usb.c . IDs 'stolen' from the
windows inf file(02/12/2009, 2.01.01.0015).
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, tmspci tokenring driver crashes on device initialization
because it requests its irq before initializing corresponding data
structures. Fix this by moving request_irq call to a safer place.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the error count a per-NIC variable.
Reset this the count after an hour if it has not reached the critical value.
Set the critical value back to 5.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When flushing queues we disable normal interrupt and event handling and
poll event queue 0 looking for flush completions. Unfortunately the
flush event polling loop fails to move past any other type of event.
This problem has not been observed in production hardware but appears to
be a possibility.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i2c_del_adapter() leaves dangling pointers in the structure. If we
retry the NIC probe and pass the structure to i2c_add_adapter() again
it will lead to an oops unless we clear it first.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If MAC switching fails, stop the port properly.
If PHY reinitialisation fails, clear the port_initialized flag.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6833c043f9 introduced the phy
auto-powerdown capability. While the APD feature only works for 5761
and 5784 asic revisions, the (harmless portion of the) code was applied
to all 5705 and newer devices. However, the 5906 phy departs from the
usual design. This commit was interfering with the 5906's ability to
negotiate link against some switches. This patch corrects the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with while (--worklimit >= 0); worklimit reaches -1 after the loop. In
3c589_cs.c this caused a warning not to be printed.
In 3c574_cs.c contrastingly, el3_rx() treats worklimit differently:
static int el3_rx(struct net_device *dev, int worklimit)
{
while (--worklimit >= 0) { ... }
return worklimit;
}
el3_rx() is only called by function el3_interrupt(): twice:
static irqreturn_t el3_interrupt(int irq, void *dev_id)
{
int work_budget = max_interrupt_work;
while(...) {
if (...)
work_budget = el3_rx(dev, work_budget);
if (...)
work_budget = el3_rx(dev, work_budget);
if (--work_budget < 0) {
...
break;
}
}
}
The error path can occur 2 too early.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with while (timeout-- > 0); timeout reaches -1 after the loop, so the tests
below are off by one. also don't do an '< 0' test on an unsigned.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the firmware is issuing events to the driver the events
must be removed from the queue. If the queue overflows, the
firmware will build and special event that captures those that
are lost.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This event will arrive at boot time or after an
MPI processor reset if the firmware failed to initialize.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This worker and it's supporting routines are used for
IDC 'inter-device-communication' events that require
an ACK mailbox command be sent to allow completion
of the request. These requests are originated by
another function wanting to change some common
port paramters. Typical example would be:
1) Change max TX/RX frame size allowed.
2) Change pause parameters.
3) Change loopback mode.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add vendor/product IDs for new no name dm9601 compatible usb ethernet
adaptors.
Reported-by: Eric Lauriault <eric@linux.ca>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limitation to only 1500 byte mtu's limits the utility of the veth
device for testing routing. So implement implement a configurable
MTU.
For consistency I drop packets on the receive side when they are
larger than the MTU. I count those drops. And I allow
a little padding for vlan headers.
I also test the mtu when a new device is created with netlink
because that path currently bypasses the current mtu setting
code.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o set port mode after resetting device.
o prefer cut-through firmware (doesn't require on-card memory).
o load flashed firmware if newer.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support larger dma mask if firmware indicates capability
to handle larger addresses.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds functionality to get and set port parameters.
Currently it is used to set maximum TX/RX frame sizes. This process is
also capable of setting:
1) Pause type: Standard or Priority based.
2) Loop back mode.
3) Enable Jumbo frame mode (included here...)
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device has more firmware support for link management, setting
TX and RX maximum frame sizes.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface will be used for setting things like maximum
frame size, setting WOL, and ACKing changes requested by the FCOE
function.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding "ethtool -d" support. Due to the complexity of the FW and HW, there are a
lot of different regions in the chip - to keep the code as clean as possible,
the ranges were put in an H file. Some areas cannot be read if the driver is
running - so by default, the driver will not access those areas - but any
programmer facing a problem will be able to easily manipulate the driver to
extract full dump. The full dump can also be used with kernel dump modules in
case of kernel panic.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the FP index to relevant debug prints and simply beautify some others
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 8726 module detection option is disabled, module should be transmitting
regardless of invalid read from EEPROM
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microcode download requires write of another register and read from
"Limiting/LRM mode" register before setting
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On unload, the FW assumes that no packets will be sent after the driver sends
the FW stop command. To ensure that, the driver must always call
netif_tx_disable
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using DMA engine (DMAE) to initialize large consecutive memories in the chip
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the napi_poll budget only when updating it. Also add a comment to explain
the rmb
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx interrupt is very short and there is no need to limit it to a budget
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
