Currently we verify if we have slaves by checking if bond->slave_list is
empty. Create a define bond_has_slaves() and use it, a bit more readable
and easier to change in the future.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has no users, so we can remove it.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it uses the hard-to-rcuify bond_for_each_slave_from(), and also
it doesn't check every slave for disrepencies between the actual
IS_UP(slave) and the slave->link == BOND_LINK_UP, but only till we find the
next suitable slave.
Fix this by using bond_for_each_slave() and storing the first good slave in
*before till we find the current_arp_slave, after that we store the first good
slave in new_slave. If new_slave is empty - use the slave stored in before,
and if it's also empty - then we didn't find any suitable slave.
Also, in the meanwhile, check for each slave status.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_find_best_slave() does not have to be balanced - i.e. return the slave
that is *after* some other slave, but rather return the best slave that
suits, except of bond->primary_slave - in which case we just return it if
it's suitable.
After that we just look through all the slaves and return either first up
slave or the slave whose link came back earliest.
We also don't care about curr_active_slave lock cause we use it in
bond_should_change_active() only and there we take it right away - i.e. it
won't go away.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we're using bond_for_each_slave_from(), which is really hard to
implement under RCU and/or neighbour list.
Remove it and use bond_for_each_slave() instead, taking care of the last
used slave.
Also, rename next_rx_slave to rx_slave and store the current (last)
rx_slave.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there are two loops - first we find the first slave in an
aggregator after the xmit_hash_policy() returned number, and after that we
loop from that slave, over bonding head, and till that slave to find any
suitable slave to send the packet through.
Replace it by just one bond_for_each_slave() loop, which first loops
through the requested number of slaves, saving the first suitable one, and
after that we've hit the requested number of slaves to skip - search for
any up slave to send the packet through. If we don't find such kind of
slave - then just send the packet through the first suitable slave found.
Logic remains unchainged, and we skip two loops. Also, refactor it a bit
for readability.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're safe agains removal there, cause we use neighbours primitives.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It needs a list_head *iter, so add it wherever needed. Use both non-rcu and
rcu variants.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only use it in rollback scenarios and can easily use the standart
bond_for_each_dev() instead.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should be used under rtnl/bonding lock, so use the non-RCU version.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new provided function when attaching the lower slave to populate
its ->private with struct slave *new_slave. Also, move it to the end to
be able to 'find' it only after it was completely initialized, and
deinitialize in the first place on release.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we distinguish neighbours (first-level linked devices) from
non-neighbours by the neighbour bool in the netdev_adjacent. This could be
quite time-consuming in case we would like to traverse *only* through
neighbours - cause we'd have to traverse through all devices and check for
this flag, and in a (quite common) scenario where we have lots of vlans on
top of bridge, which is on top of a bond - the bonding would have to go
through all those vlans to get its upper neighbour linked devices.
This situation is really unpleasant, cause there are already a lot of cases
when a device with slaves needs to go through them in hot path.
To fix this, introduce a new upper/lower device lists structure -
adj_list, which contains only the neighbours. It works always in
pair with the all_adj_list structure (renamed from upper/lower_dev_list),
i.e. both of them contain the same links, only that all_adj_list contains
also non-neighbour device links. It's really a small change visible,
currently, only for __netdev_adjacent_dev_insert/remove(), and doesn't
change the main linked logic at all.
Also, add some comments a fix a name collision in
netdev_for_each_upper_dev_rcu() and rework the naming by the following
rules:
netdev_(all_)(upper|lower)_*
If "all_" is present, then we work with the whole list of upper/lower
devices, otherwise - only with direct neighbours. Uninline functions - to
get better stack traces.
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
running bonding in ALB mode requires that learning packets be sent periodically,
so that the switch knows where to send responding traffic. However, depending
on switch configuration, there may not be any need to send traffic at the
default rate of 3 packets per second, which represents little more than wasted
data. Allow the ALB learning packet interval to be made configurable via sysfs
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Acked-by: Veaceslav Falico <vfalico@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We make bond_arp_rcv global so it can be used in bond_sysfs if the bond
interface is up and arp_interval is being changed to a positive value
and cleared otherwise as per Jay's suggestion.
This also fixes a problem where bond_arp_rcv was set even though
arp_validate was disabled while the bond was up by unsetting recv_probe
in bond_store_arp_validate and respectively setting it if enabled.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to protect store_arp_validate via rtnl because it can race with
mode changing and we can end up having arp_validate set in a mode
different from active-backup.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_compute_features is always called with RTNL held, so we can safely
drop the read bond->lock.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're protected by RTNL so nothing can happen and we can safely drop the
read bond->lock.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can drop the use of bond->lock for mutual exclusion in
bond_3ad_update_lacp_rate and use RTNL in the sysfs store function
instead. This way we'll prevent races with mode change and interface
up/down as well as simplify update_lacp_rate by removing the check for
port->slave because it'll always be initialized (done while enslaving
with RTNL). This change will also help in the future removal of reader
bond->lock from bond_enslave.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't have to release all slaves when closing the bond dev, so remove
the outdated comment and the braces around the left single statement.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aims to remove a use of the bond->lock for mutual exclusion
which will later allow easier migration to RCU of the users of this
functionality. We use RTNL as a synchronizing mechanism since it's
always held when send_peer_notif is set, and when it is decremented from
the notifier function. We can also drop some locking, and fix the
leakage of the send_peer_notif counter.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store VID in ->vlan_id (if any), and remove the useless ->tag.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're using it currently to verify if we have vlans before getting the tag
from the skb we're about to send. It's useless because the vlan_get_tag()
verifies if the skb has the tag (and returns an error if not), and we can
receive tagged skbs only if we *already* have vlans.
Plus, the current RCUed implementation is kind of useless anyway - the we
can remove the last vlan in the moment we return from the function.
So remove the only usage of it and the whole function.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They're simply annoying and will spam dmesg constantly if we hit them, so
convert to pr_debug so that we still can access them in case of debugging.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are no real users of vlan_list/current_alb_vlan, only the
helpers which maintain them, so remove them.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if there are vlans on top of bond, alb_send_learning_packets()
will never send LPs from the bond itself (i.e. untagged), which might leave
untagged clients unupdated.
Also, the 'circular vlan' logic (i.e. update only MAX_LP_BURST vlans at a
time, and save the last vlan for the next update) is really suboptimal - in
case of lots of vlans it will take a lot of time to update every vlan. It
is also never called in any hot path and sends only a few small packets -
thus the optimization by itself is useless.
So remove the whole current_alb_vlan/MAX_LP_BURST logic from
alb_send_learning_packets(). Instead, we'll first send a packet untagged
and then traverse the upper dev list, sending a tagged packet for each vlan
found. Also, remove the MAX_LP_BURST define - we already don't need it.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create alb_send_lp_vid(), which will handle the skb/lp creation, vlan
tagging and sending, and use it in alb_send_learning_packets().
This way all the logic remains in alb_send_learning_packets(), which
becomes a lot more cleaner and easier to understand.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We always hold the rtnl_lock() in __bond_release_one(), so use
vlan_uses_dev() instead of bond_vlan_used().
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bond_has_this_ip() is aware only of vlan upper devices, and thus
will return false if the address is associated with the upper bridge or any
other device, and thus will break the arp logic.
Fix this by using the upper device list. For every upper device we verify
if the address associated with it is our address, and if yes - return true.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bond_arp_send_all() is aware only of vlans, which breaks
configurations like bond <- bridge (or any other 'upper' device) with IP
(which is quite a common scenario for virt setups).
To fix this we convert the bond_arp_send_all() to first verify if the rt
device is the bond itself, and if not - to go through its list of upper
vlans and their respectiv upper devices (if the vlan's upper device matches
- tag the packet), if still not found - go through all of our upper list
devices to see if any of them match the route device for the target. If the
match is a vlan device - we also save its vlan_id and tag it in
bond_arp_send().
Also, clean the function a bit to be more readable.
CC: Vlad Yasevich <vyasevic@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert bond_vlan_used() to traverse the upper device list to see if we
have any vlans above us. It's protected by rcu, and in case we are holding
rtnl_lock we should call vlan_uses_dev() instead - it's faster.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code in the add bond vlan ids error
handling case instead of 0, as done elsewhere in this function.
Introduced by commit 1ff412ad77.
(bonding: change the bond's vlan syncing functions with the standard ones)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of bond_add_vlan() failure currently we'll have the vlan's
refcnt bumped up in all slaves, but it will never go down because it
failed to get added to the bond, so properly unwind the added vlan if
bond_add_vlan fails.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we have vlan_vids_add/del_by_dev() which serve the same purpose as
bond's bond_add/del_vlans_on_slave() with the good side effect of
reverting the changes if one of the additions fails.
There's only 1 change in the behaviour of enslave: if adding of the
vlans to the slave fails, we'll fail the enslaving because otherwise we
might delete some vlan that wasn't added by the bonding.
The only way this may happen is with ENOMEM currently, so we're in trouble
anyway.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're already protected by RTNL lock, so nothing can happen to bond/its
slaves, and thus the locking is useless here (both bond->lock and
bond->curr_active_slave).
Also, add ASSERT_RTNL() both to bond_set_rx_mode() and bond_hw_addr_swap()
to catch possible uses of it without RTNL locking.
This patch also saves us from a lockdep false-positive in
bond_set_rx_mode() vs bond_hw_addr_swap().
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use a lot of time comparison math for arp_interval
comparisons, which are sometimes quite hard to read and understand.
All the time comparisons have one pattern:
(time - arp_interval_jiffies) <= jiffies <= (time + mod *
arp_interval_jiffies + arp_interval_jiffies/2)
Introduce a new helper - bond_time_in_interval(), which will do the math in
one place and, thus, will clean up the logical code. This helper introduces
a bit of overhead (by always calculating the jiffies from arp_interval),
however it's really not visible, considering that functions using it
usually run once in arp_interval milliseconds.
There are several lines slightly over 80 chars, however breaking them would
result in more hard-to-read code than several character after the 80 mark.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple cleanup to not call slave_last_rx() on every time function. It won't
give any measurable boost - but looks cleaner and easier to understand.
There are no time-consuming functions in between these calls, so it's safe
to call it in the beginning only once.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, on neighbour creation, bond_neigh_init() will be called with a
foreign netdev.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does the initial bonding conversion to RCU. After it the
following modes are protected by RCU alone: roundrobin, active-backup,
broadcast and xor. Modes ALB/TLB and 3ad still acquire bond->lock for
reading, and will be dealt with later. curr_active_slave needs to be
dereferenced via rcu in the converted modes because the only thing
protecting the slave after this patch is rcu_read_lock, so we need the
proper barrier for weakly ordered archs and to make sure we don't have
stale pointer. It's not tagged with __rcu yet because there's still work
to be done to remove the curr_slave_lock, so sparse will complain when
rcu_assign_pointer and rcu_dereference are used, but the alternative to use
rcu_dereference_protected would've created much bigger code churn which is
more difficult to test and review. That will be converted in time.
1. Active-backup mode
1.1 Perf recording while doing iperf -P 4
- old bonding: iperf spent 0.55% in bonding, system spent 0.29% CPU
in bonding
- new bonding: iperf spent 0.29% in bonding, system spent 0.15% CPU
in bonding
1.2. Bandwidth measurements
- old bonding: 16.1 gbps consistently
- new bonding: 17.5 gbps consistently
2. Round-robin mode
2.1 Perf recording while doing iperf -P 4
- old bonding: iperf spent 0.51% in bonding, system spent 0.24% CPU
in bonding
- new bonding: iperf spent 0.16% in bonding, system spent 0.11% CPU
in bonding
2.2 Bandwidth measurements
- old bonding: 8 gbps (variable due to packet reorderings)
- new bonding: 10 gbps (variable due to packet reorderings)
Of course the latency has improved in all converted modes, and moreover
while
doing enslave/release (since it doesn't affect tx anymore).
Also I've stress tested all modes doing enslave/release in a loop while
transmitting traffic.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I factored out the tx xmit code which relies on slave id in
bond_xmit_slave_id. It is global because later it can be used also in
3ad mode xmit. Unnecessary obvious comments are removed. Active-backup
mode is simplified because bond_dev_queue_xmit always consumes the skb.
bond_xmit_xor becomes one line because of bond_xmit_slave_id.
bond_for_each_slave_from is not used in bond_xmit_slave_id because later
when RCU is used we can avoid important race condition by using standard
rculist routines.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need to start from the curr_active_slave as the frame will be
sent to all eligible slaves anyway, so we remove the unnecessary local
variables, checks and comments, and make it use the standard list API.
This has the nice side-effect that later when it's converted to RCU
a race condition will be avoided which could lead to double packet tx.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all the cases we already hold bond->lock for reading, so the slave
can't get away and the check != NULL is sufficient. curr_active_slave
can still change after the read_lock is unlocked prior to use of the
dereferenced value, so there's no need for it. It either contains a
valid slave which we use (and can't get away), or it is NULL which is
checked.
In some places the read_lock of curr_slave_lock was left because we need
it not to change while performing some action (e.g. syncing current
active slave's addresses, sending ARP requests through the active slave)
such cases will be dealt with individually while converting to RCU.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aims to remove struct bonding's first_slave and struct
slave's next and prev pointers, and replace them with the standard Linux
list API. The old macros are converted to list API as well and some new
primitives are available now. The checks if there're slaves that used
slave_cnt have been replaced by the list_empty macro.
Also a few small style fixes, changing longest -> shortest line in local
variable declarations, leaving an empty line before return and removing
unnecessary brackets.
This is the first step to gradual RCU conversion.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 4aa5dee4d9 ("net: convert resend IGMP to notifier event")
we try to acquire rtnl in bond_resend_igmp_join_requests but it can be
scheduled with rtnl already held (e.g. when bond_change_active_slave is
called with rtnl) causing a loop of immediate reschedules + calls because
rtnl_trylock fails each time since it's being already held.
For me this issue leads to system hangs very easy:
modprobe bonding; ifconfig bond0 up; ifenslave bond0 eth0; rmmod
bonding;
The fix is to introduce a small (1 jiffy) delay which is enough for the
sections holding rtnl to finish without putting any strain on the system.
Also adjust the timer in bond_change_active_slave to be 1 jiffy, since
most of the time it's called with rtnl already held.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 4aa5dee4d9 ("net: convert resend IGMP to notifier event") we
have 1 read_unlock in bond_resend_igmp_join_requests which isn't paired
with a read_lock because it's removed by that commit.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This started out with fixing a sparse warning, then I realized that
the wrapper function bond_netpoll_info could just be removed
by rolling it into the enable code.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have BOND_MODE_ROUNDROBIN pre-defined as 0, and it's the lowest
mode number.
Use it to check the arg lower bound instead of magic number 0 in
bond_mode_name.
Signed-off-by: Wang Sheng-Hui <shhuiw@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error is found by the checkpatch.pl tools.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need rtnl protection while reading slave_cnt and updating
the .fail_over_mac, and it also follows the logic "don't change
anything slave-related without rtnl". :)
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/bonding/bond_sysfs.c:1302: ERROR: else should follow close brace '}'
net/bonding/bond_sysfs.c:1314: ERROR: else should follow close brace '}'
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The slave_xxx_netpoll will call synchronize_rcu_bh(),
so the function may schedule and sleep, it should't be
called under spinlocks.
bond_netpoll_setup() and bond_netpoll_cleanup() are always
protected by rtnl lock, it is no need to take the read lock,
as the slave list couldn't be changed outside rtnl lock.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
