Mechanism of selecting physical mode in genapic when cpu hotplug is enabled on
x86_64, broke the quirk(quirk_intel_irqbalance()) introduced for working
around the transposing interrupt message errata in E7520/E7320/E7525 (revision
ID 0x9 and below. errata #23 in
http://download.intel.com/design/chipsets/specupdt/30304203.pdf).
This errata requires the mode to be in logical flat, so that interrupts can be
directed to more than one cpu(and thus use hardware IRQ balancing enabled by
BIOS on these platforms).
Following four patches fixes this by moving the quirk to early quirk and
forcing the x86_64 genapic selection to logical flat on these platforms.
Thanks to Shaohua for pointing out the breakage.
This patch:
Add write_pci_config_byte() to direct PCI access routines
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: "Li, Shaohua" <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
o Convert more absolute symbols to section relative to keep the theme in
vmlinux.lds.S file and to avoid problem if kernel is relocated.
o Also put a message so that in future people can be aware of it and
avoid introducing absolute symbols.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Make the needlessly global alloc_gdt() static.
(against) pda-percpu-init
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Until not so long ago, there were system log messages pointing to
inconsistent MTRR setup of the video frame buffer caused by the way vesafb
and X worked. While vesafb was fixed meanwhile, I believe fixing it there
only hides a shortcoming in the MTRR code itself, in that that code is not
symmetric with respect to the ordering of attempts to set up two (or more)
regions where one contains the other. In the current shape, it permits
only setting up sub-regions of pre-exisiting ones. The patch below makes
this symmetric.
While working on that I noticed a few more inconsistencies in that code,
namely
- use of 'unsigned int' for sizes in many, but not all places (the patch
is converting this to use 'unsigned long' everywhere, which specifically
might be necessary for x86-64 once a processor supporting more than 44
physical address bits would become available)
- the code to correct inconsistent settings during secondary processor
startup tried (if necessary) to correct, among other things, the value
in IA32_MTRR_DEF_TYPE, however the newly computed value would never get
used (i.e. stored in the respective MSR)
- the generic range validation code checked that the end of the
to-be-added range would be above 1MB; the value checked should have been
the start of the range
- when contained regions are detected, previously this was allowed only
when the old region was uncacheable; this can be symmetric (i.e. the new
region can also be uncacheable) and even further as per Intel's
documentation write-trough and write-back for either region is also
compatible with the respective opposite in the other
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Just like on x86-64, don't touch foreign CPUs' memory if the watchdog
isn't enabled at all.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
While not strictly required with the current code (as the upper half of
page table entries generated by __set_fixmap() cannot be non-zero due
to the second parameter of this function being 'unsigned long'), the
use of set_pte() in __set_fixmap() in the context of clear_fixmap() is
still improper with CONFIG_X86_PAE (see the respective comment in
include/asm-i386/pgtable-3level.h) and would turn into a bug if that
second parameter ever gets changed to a 64-bit type.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The final line of /proc/<pid>/maps on x86_64 for native 64-bit
tasks shows an incorrect ending address and incorrect permissions. There
is only a single page mapped in this vsyscall region, and it is accessible
for both read and execute.
The patch below fixes this. (Since 32-bit-compat tasks have a real vma
with correct perms/range, no change is necessary for that scenario.)
Before the patch, a "cat /proc/self/maps | tail -1" shows this:
ffffffffff600000-ffffffffffe00000 ---p 00000000 [...]
After the patch, this is the output:
ffffffffff600000-ffffffffff601000 r-xp 00000000 [...]
Signed-off-by: Ernie Petrides <petrides@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
gcc doesn't support -mtune=core2 yet, but will be soon. Use -mtune=generic or -mtune=i686
as fallback
TBD need benchmarking for INTEL_USERCOPY etc. So far I used the same defaults as MPENTIUMM
Signed-off-by: Andi Kleen <ak@suse.de>
Add an option to compile for Intel's Core 2
The Kconfig help is a mouthful due to the inventiveness of Intel's
product naming department.
Mainly for the 64bit cache line sizes because gcc doesn't support
optimizing for core2 yet. However it will and then the kernel
should be ready by passing the right option
Also fix the old MPSC help text to confirm better to reality.
Signed-off-by: Andi Kleen <ak@suse.de>
Add a way to disable the timer IRQ routing check via a boot option. The
VMI timer code uses this to avoid triggering the pester Mingo code, which
probes for some very unusual and broken motherboard routings. It fires
100% of the time when using a paravirtual delay mechanism instead of using
a realtime delay, since there is no elapsed real time, and the 4 timer IRQs
have not yet been delivered.
In addition, it is entirely possible, though improbable, that this bug
could surface on real hardware which picks a particularly bad time to enter
SMM mode, causing a long latency during one of the timer IRQs.
While here, make check_timer be __init.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
[chrisw: use no_timer_check to bring inline with x86_64 as per Andi's request]
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
BIOS ROM areas may not be mapped into the guest address space, so be careful
when touching those addresses to make sure they appear to be mapped.
[akpm@osdl.org: fix unused var warning]
AK: Changed __get_user to probe_kernel_address
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Add the three bare TLB accessor functions to paravirt-ops. Most amusingly,
flush_tlb is redefined on SMP, so I can't call the paravirt op flush_tlb.
Instead, I chose to indicate the actual flush type, kernel (global) vs. user
(non-global). Global in this sense means using the global bit in the page
table entry, which makes TLB entries persistent across CR3 reloads, not
global as in the SMP sense of invoking remote shootdowns, so the term is
confusingly overloaded.
AK: folded in fix from Zach for PAE compilation
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Add APIC accessors to paravirt-ops. Unfortunately, we need two write
functions, as some older broken hardware requires workarounds for
Pentium APIC errata - this is the purpose of apic_write_atomic.
AK: replaced __inline with inline
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Two legacy power management modes are much easier to just explicitly disable
when running in paravirtualized mode - neither APM nor PnP is still relevant.
The status of ACPI is still debatable, and noacpi is still a common enough
boot parameter that it is not necessary to explicitly disable ACPI.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Allow selected bug checks to be skipped by paravirt kernels. The two most
important are the F00F workaround (which is either done by the hypervisor,
or not required), and the 'hlt' instruction check, which can break under
some hypervisors.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
1) Each hypervisor writes a probe function to detect whether we are
running under that hypervisor. paravirt_probe() registers this
function.
2) If vmlinux is booted with ring != 0, we call all the probe
functions (with registers except %esp intact) in link order: the
winner will not return.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Both lhype and Xen want to call the core of the x86 cpu detect code before
calling start_kernel.
(extracted from larger patch)
AK: folded in start_kernel header patch
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
It turns out that the most called ops, by several orders of magnitude,
are the interrupt manipulation ops. These are obvious candidates for
patching, so mark them up and create infrastructure for it.
The method used is that the ops structure has a patch function, which
is called for each place which needs to be patched: this returns a
number of instructions (the rest are NOP-padded).
Usually we can spare a register (%eax) for the binary patched code to
use, but in a couple of critical places in entry.S we can't: we make
the clobbers explicit at the call site, and manually clobber the
allowed registers in debug mode as an extra check.
And:
Don't abuse CONFIG_DEBUG_KERNEL, add CONFIG_DEBUG_PARAVIRT.
And:
AK: Fix warnings in x86-64 alternative.c build
And:
AK: Fix compilation with defconfig
And:
^From: Andrew Morton <akpm@osdl.org>
Some binutlises still like to emit references to __stop_parainstructions and
__start_parainstructions.
And:
AK: Fix warnings about unused variables when PARAVIRT is disabled.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Create a paravirt.h header for all the critical operations which need to be
replaced with hypervisor calls, and include that instead of defining native
operations, when CONFIG_PARAVIRT.
This patch does the dumbest possible replacement of paravirtualized
instructions: calls through a "paravirt_ops" structure. Currently these are
function implementations of native hardware: hypervisors will override the ops
structure with their own variants.
All the pv-ops functions are declared "fastcall" so that a specific
register-based ABI is used, to make inlining assember easier.
And:
+From: Andy Whitcroft <apw@shadowen.org>
The paravirt ops introduce a 'weak' attribute onto memory_setup().
Code ordering leads to the following warnings on x86:
arch/i386/kernel/setup.c:651: warning: weak declaration of
`memory_setup' after first use results in unspecified behavior
Move memory_setup() to avoid this.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
IOPL is implicitly saved and restored on task switch,
so explicit check is no longer needed.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Port two patches from i386 to x86_64 delay.c to make sure all rounding is done
upward instead of downward.
There is no sign in commit messages that the mismatch was done on purpose, and
"delay() guarantees sleeping at least for the specified time" is still a valid
rule IMHO.
The original x86 patches are both from pre-GIT era, i.e.:
"[PATCH] round up in __udelay()" in commit
54c7e1f5cc6771ff644d7bc21a2b829308bd126f
"[PATCH] add 1 in __const_udelay()" in commit
42c77a9801b8877d8b90f65f75db758822a0bccc
(both commits are from converted BK repository to x86_64).
AK: fixed gcc warning
linux/arch/x86_64/lib/delay.c:43: warning: suggest parentheses around + or - inside shift
(did this actually work?)
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch makes it possible to compile Calgary in but not use it by
default. In this mode, use 'iommu=calgary' to activate it.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch cleans up the previous "Use BIOS supplied BBAR information"
patch. Mostly stylistic clenaups, but also check for ioremap failure
when we ioremap the BBAR rather than when trying to use it.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Laurent Vivier <Laurent.Vivier@bull.net>
Find the BBAR register address of each Calgary using the "Extended
BIOS Data Area" rather than calculating it ourselves. Also get the bus
topology (what PHB each bus is on) from Calgary rather than
calculating it ourselves.
This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=7407.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Andi Kleen <ak@suse.de>
The recent change to make x86_64 support i386 binaries compiled
with -mregparm=3 only covered signal handlers without SA_SIGINFO.
(the 3-arg "real-time" ones)
To be compatible with i386, both types should be supported.
Signed-off-by: Albert Cahalan <acahalan@gmail.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Instead of adding all kinds of more quirks try various timer
routing variants in check_timer.
In particular this tries to handle quirks from:
- Nvidia NF2-4 reference BIOS: wrong timer override
- Asus: Wrong timer override but no HPET table
- ATI: require timer disabled in 8259
- Some boards: require timer enabled in 8259
We just try many of the the known variants in the hopefully right order
in check_timer.
Trying pin 0/2 on Nvidia suggested by Tim Hockin.
TBD Experimental. Needs a lot of testing
Signed-off-by: Andi Kleen <ak@suse.de>
Makes the intention of the code cleaner to read and avoids
a potential deadlock on mmap_sem. Also change the types of
the arguments to not include __user because they're really
not user addresses.
Signed-off-by: Andi Kleen <ak@suse.de>
Clear the irq releated entries in irq_vector, irq_domain and vector_irq
instead of clearing irq_vector only. So when new irq is created, it
could reuse that vector. (actually is the second loop scanning from
FIRST_DEVICE_VECTOR+8). This could avoid the vectors are used up
with enough module inserting and removing
Cc: Eric W. Biedierman <ebiederm@xmission.com>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-By: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
CLFLUSH is a lot faster than WBINVD so avoid the later if at all
possible.
Always pass the complete list of pages to other CPUs to cut down
the number of IPIs.
Minor other cleanup and sync with i386 version.
Signed-off-by: Andi Kleen <ak@suse.de>
The entry.S code at work_notifysig is surely wrong. It drops into unrelated
code if the branch to work_notifysig_v86 is taken, and CONFIG_VM86=n.
[PATCH] Make vm86 support optional
tree 9b5daef528
pushed to git Jan 8, 2006, and first appears in 2.6.16
The 'fix' here is to also compile out the vm86 test & branch when
CONFIG_VM86=n.
Signed-off-by: Joe Korty <joe.korty@ccur.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Extend bzImage protocol to enable bootloaders to load a completely relocatable
bzImage. Now protected mode component of kernel is also relocatable and a
boot-loader can load the protected mode component at a differnt physical
address than 1MB. (If kernel was built with CONFIG_RELOCATABLE)
Kexec can make use of it to load this kernel at a different physical address
to capture kernel crash dumps.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
o Now CONFIG_PHYSICAL_START is being replaced with CONFIG_PHYSICAL_ALIGN.
Hardcoding the kernel physical start value creates a problem in relocatable
kernel context due to boot loader limitations. For ex, if somebody
compiles a relocatable kernel to be run from address 4MB, but this kernel
will run from location 1MB as grub loads the kernel at physical address
1MB. Kernel thinks that I am a relocatable kernel and I should run from
the address I have been loaded at. So somebody wanting to run kernel
from 4MB alignment location (for improved performance regions) can't do
that.
o Hence, Eric proposed that probably CONFIG_PHYSICAL_ALIGN will make
more sense in relocatable kernel context. At run time kernel will move
itself to a physical addr location which meets user specified alignment
restrictions.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
o Relocations generated w.r.t absolute symbols are not processed as by
definition, absolute symbols are not to be relocated. Explicitly warn
user about absolutions relocations present at compile time.
o These relocations get introduced either due to linker optimizations or
some programming oversights.
o Also create a list of symbols which have been audited to be safe and
don't emit warnings for these.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch modifies the i386 kernel so that if CONFIG_RELOCATABLE is
selected it will be able to be loaded at any 4K aligned address below
1G. The technique used is to compile the decompressor with -fPIC and
modify it so the decompressor is fully relocatable. For the main
kernel relocations are generated. Resulting in a kernel that is relocatable
with no runtime overhead and no need to modify the source code.
A reserved 32bit word in the parameters has been assigned
to serve as a stack so we figure out where are running.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Print the addresses of non-absolute symbols relative to _text
so that ld will generate relocations. Allowing a relocatable
kernel to relocate them. We can't actually use the symbol names
because kallsyms includes static symbols that are not exported
from their object files.
Add the _text symbol definitions to the architectures which don't
define it otherwise linker will fail.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Defining __PHYSICAL_START and __KERNEL_START in asm-i386/page.h works but
it triggers a full kernel rebuild for the silliest of reasons. This
modifies the users to directly use CONFIG_PHYSICAL_START and linux/config.h
which prevents the full rebuild problem, which makes the code much
more maintainer and hopefully user friendly.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Currently when we are reserving the memory the kernel text
resides in we start at __PHYSICAL_START which happens to be
correct but not very obvious. In addition when we start relocating
the kernel __PHYSICAL_START is the wrong value, as it is an
absolute symbol that does not get relocated.
By starting the reservation at __pa_symbol(_text)
the code is clearer and will be correct when relocated.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Ld knows about 2 kinds of symbols, absolute and section
relative. Section relative symbols symbols change value
when a section is moved and absolute symbols do not.
Currently in the linker script we have several labels
marking the beginning and ending of sections that
are outside of sections, making them absolute symbols.
Having a mixture of absolute and section relative
symbols refereing to the same data is currently harmless
but it is confusing.
This must be done carefully as newer revs of ld do not place
symbols that appear in sections without data and instead
ld makes those symbols global :(
My ultimate goal is to build a relocatable kernel. The
safest and least intrusive technique is to generate
relocation entries so the kernel can be relocated at load
time. The only penalty would be an increase in the size
of the kernel binary. The problem is that if absolute and
relocatable symbols are not properly specified absolute symbols
will be relocated or section relative symbols won't be, which
is fatal.
The practical motivation is that when generating kernels that
will run from a reserved area for analyzing what caused
a kernel panic, it is simpler if you don't need to hard code
the physical memory location they will run at, especially
for the distributions.
[AK: and merged:]
o Also put a message so that in future people can be aware of it and
avoid introducing absolute symbols.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
On modern systems RAM errors don't cause NMIs, but it's usually
caused by PCI SERR. Mention PCI instead of RAM in the printk.
Reported by r_hayashi@ctc-g.co.jp (Ryutaro Hayashi)
Cc: r_hayashi@ctc-g.co.jp
Signed-off-by: Andi Kleen <ak@suse.de>
Resending as I believe the discussion about them established they were
correct.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Currently the idle loop has two nested loops -- one high level
in cpu_idle and in some low level idle functions another one.
Looping in the low level idle functions breaks the idle notifiers
because interrupts waking up sleep states need to execute
exit_idle() which is only in cpu_idle().
So don't do that, only loop in cpu_idle(). This only removes
code.
In some cases e.g. poll_idle the idle loop is a little longer
now because cpu_idle checks more things. I hope that isn't a problem
ACPI idle doesn't change behaviour because it never looped anyways.
Cc: len.brown@intel.com
Cc: eranian@hpl.hp.com
Signed-off-by: Andi Kleen <ak@suse.de>
Use the pcurrent field in the PDA to implement the "current" macro. This ends
up compiling down to a single instruction to get the current task.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use the cpu_number in the PDA to implement raw_smp_processor_id. This is a
little simpler than using thread_info, though the cpu field in thread_info
cannot be removed since it is used for things other than getting the current
CPU in common code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
sys_vm86 uses a struct kernel_vm86_regs, which is identical to pt_regs, but
adds an extra space for all the segment registers. Previously this structure
was completely independent, so changes in pt_regs had to be reflected in
kernel_vm86_regs. This changes just embeds pt_regs in kernel_vm86_regs, and
makes the appropriate changes to vm86.c to deal with the new naming.
Also, since %gs is dealt with differently in the kernel, this change adjusts
vm86.c to reflect this.
While making these changes, I also cleaned up some frankly bizarre code which
was added when auditing was added to sys_vm86.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
There are a few places where the change in struct pt_regs and the use of %gs
affect the userspace ABI. These are primarily debugging interfaces where
thread state can be inspected or extracted.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch is the meat of the PDA change. This patch makes several related
changes:
1: Most significantly, %gs is now used in the kernel. This means that on
entry, the old value of %gs is saved away, and it is reloaded with
__KERNEL_PDA.
2: entry.S constructs the stack in the shape of struct pt_regs, and this
is passed around the kernel so that the process's saved register
state can be accessed.
Unfortunately struct pt_regs doesn't currently have space for %gs
(or %fs). This patch extends pt_regs to add space for gs (no space
is allocated for %fs, since it won't be used, and it would just
complicate the code in entry.S to work around the space).
3: Because %gs is now saved on the stack like %ds, %es and the integer
registers, there are a number of places where it no longer needs to
be handled specially; namely context switch, and saving/restoring the
register state in a signal context.
4: And since kernel threads run in kernel space and call normal kernel
code, they need to be created with their %gs == __KERNEL_PDA.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
When a CPU is brought up, a PDA and GDT are allocated for it. The GDT's
__KERNEL_PDA entry is pointed to the allocated PDA memory, so that all
references using this segment descriptor will refer to the PDA.
This patch rearranges CPU initialization a bit, so that the GDT/PDA are set up
as early as possible in cpu_init(). Also for secondary CPUs, GDT+PDA are
preallocated and initialized so all the secondary CPU needs to do is set up
the ldt and load %gs. This will be important once smp_processor_id() and
current use the PDA.
In all cases, the PDA is set up in head.S, before a CPU starts running C code,
so the PDA is always available.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch has the basic definitions of struct i386_pda, and the segment
selector in the GDT.
asm-i386/pda.h is more or less a direct copy of asm-x86_64/pda.h. The most
interesting difference is the use of _proxy_pda, which is used to give gcc a
model for the actual memory operations on the real pda structure. No actual
reference is ever made to _proxy_pda, so it is never defined.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use asm-offsets for the offsets of registers into the pt_regs struct, rather
than having hard-coded constants
I left the constants in the comments of entry.S because they're useful for
reference; the code in entry.S is very dependent on the layout of pt_regs,
even when using asm-offsets.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Keith Owens <kaos@ocs.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch:
- makes ret_from_sys_call no longer global (all external users were
previously switched to use int_ret_from_sys_call)
- adjusts placement of a CFI_{REMEMBER,RESTORE}_STATE pair to better
fit logic flow
- eliminates an unnecessary pair of CFI_{REMEMBER,RESTORE}_STATE
- glues together function- and unwinder-wise the previously separate
system_call and int_ret_from_sys_call function fragments
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Tested (compilation only):
- using allmodconfig
- making sure the files are compiling without any warning/error due to
new changes
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Insert the Local APIC and IO APIC(s) into the resource tree. It allows the
APIC resources to be visible within /proc/iomem. The patch also takes into
account IO APIC(s) mapped in the PCI space by deferring the insertion until
after PCI has allocated its necessary resources.
Signed-off-by: Aaron Durbin <adurbin@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
i386 port of the sLeAZY-fpu feature. Chuck reports that this gives him a +/-
0.4% improvement on his simple benchmark
x86_64 description follows:
Right now the kernel on x86-64 has a 100% lazy fpu behavior: after *every*
context switch a trap is taken for the first FPU use to restore the FPU
context lazily. This is of course great for applications that have very
sporadic or no FPU use (since then you avoid doing the expensive save/restore
all the time). However for very frequent FPU users... you take an extra trap
every context switch.
The patch below adds a simple heuristic to this code: After 5 consecutive
context switches of FPU use, the lazy behavior is disabled and the context
gets restored every context switch. If the app indeed uses the FPU, the trap
is avoided. (the chance of the 6th time slice using FPU after the previous 5
having done so are quite high obviously).
After 256 switches, this is reset and lazy behavior is returned (until there
are 5 consecutive ones again). The reason for this is to give apps that do
longer bursts of FPU use still the lazy behavior back after some time.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Clean up the espfix code:
- Introduced PER_CPU() macro to be used from asm
- Introduced GET_DESC_BASE() macro to be used from asm
- Rewrote the fixup code in asm, as calling a C code with the altered %ss
appeared to be unsafe
- No longer altering the stack from a .fixup section
- 16bit per-cpu stack is no longer used, instead the stack segment base
is patched the way so that the high word of the kernel and user %esp
are the same.
- Added the limit-patching for the espfix segment. (Chuck Ebbert)
[jeremy@goop.org: use the x86 scaling addressing mode rather than shifting]
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Zachary Amsden <zach@vmware.com>
Acked-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
When a spinlock lockup occurs, arrange for the NMI code to emit an all-cpu
backtrace, so we get to see which CPU is holding the lock, and where.
Cc: Andi Kleen <ak@muc.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch removes the default_ldt[] array, as it has been unused since
iBCS stopped being supported. This means it is now possible to actually
set an empty LDT segment.
In order to deal with this, the set_ldt_desc/load_LDT pair has been
replaced with a single set_ldt() operation which is responsible for both
setting up the LDT descriptor in the GDT, and reloading the LDT register.
If there are no LDT entries, the LDT register is loaded with a NULL
descriptor.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Acked-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Here is a patch (used by perfmon2) to detect the presence of the Precise Event
Based Sampling (PEBS) feature for i386. The patch also adds the cpu_has_pebs
macro.
- adds X86_FEATURE_PEBS
- adds cpu_has_pebs to test for X86_FEATURE_PEBS
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Here is a patch (used by perfmon2) to detect the presence of the
Precise Event Based Sampling (PEBS) feature for Intel 64-bit processors.
The patch also adds the cpu_has_pebs macro.
changelog:
- adds X86_FEATURE_PEBS
- adds cpu_has_pebs to test for X86_FEATURE_PEBS
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
This just got removed on x86-64, do the same on 32bit.
It always annoyed me when this ate a line of oops output pushing
interesting stuff off the screen.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The unwinder has some extra newlines, which eat up loads of screen
space when it spews. (See https://bugzilla.redhat.com/bugzilla/attachment.cgi?id=137900
for a nasty example).
warning_symbol-> and warning-> already printk a newline, so don't add one
in the strings passed to them.
[AK: redone for new code]
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix checks that failed to realize that values are 4-kB-unit-sized (note the
format strings in this same diff context which *do* realize the unit size,
via appended "000"!). Also fix an incorrect below-1MB area check (as
gathered from Jan Beulich's unapplied patch at
http://www.ussg.iu.edu/hypermail/linux/kernel/0411.1/1378.html ) Update
mtrr_add_page() docu to make 4-kB-sized calculation more obvious.
Given several further items mentioned in Jan's patch mail, all in all MTRR
code seems surprisingly buggy, for a surprisingly long period of time (many
years). Further work/investigation would be useful.
TBD Note that my patch is pretty much UNTESTED, since I can only verify that it
TBD successfully boots my machine, but I cannot test against actual buggy
TBD hardware which would require these (formerly broken) checks. Long -mm
TBD simmering would make sense, especially since these now-working checks might
TBD turn out to have adverse effects on unaffected hardware.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Import updates from i386's i8259.c
[MIPS] *-berr: Header inclusions for DEC bus error handlers
[MIPS] Compile __do_IRQ() when really needed
[MIPS] genirq: use name instead of typename
[MIPS] Do not use handle_level_irq for ioasic_dma_irq_type.
[MIPS] pte_offset(dir,addr): parenthesis fix
The recent change to convert the is_enabled flag in the PCI device to an
atomic count broke the IA64 compilation.
As pcibios_disable_device is only ever called if the reference count
is zero, convert the if to a BUG_ON.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
A fixup to add missing header inclusions for bus error handlers for
DECstation system after the recent switch to get_irq_regs().
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
__do_IRQ() is needed only by irq handlers that can't use
default handlers defined in kernel/irq/chip.c.
For others platforms there's no need to compile this function
since it won't be used. For those platforms this patch defines
GENERIC_HARDIRQS_NO__DO_IRQ symbol which is used exactly for
this purpose.
Futhermore for platforms which do not use __do_IRQ(), end()
method which is part of the 'irq_chip' structure is not used.
This patch simply removes this method in this case.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The "typename" field was obsoleted by the "name" field.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (43 commits)
sh: sh775x/titan fixes for irq header changes.
sh: update r7780rp defconfig.
sh: compile fixes for header cleanup.
sh: Fixup pte_mkhuge() build failure.
sh: set KBUILD_IMAGE to something sensible.
sh: show held locks in stack trace with lockdep.
sh: platform_pata support for R7780RP
sh: stacktrace/lockdep/irqflags tracing support.
sh: Fixup movli.l/movco.l atomic ops for gcc4.
sh: dyntick infrastructure.
sh: Clock framework tidying.
sh: Turn off IRQs around get_timer_offset() calls.
sh: Get the PGD right in oops case with 64-bit PTEs.
sh: Fix store queue bitmap end.
sh: More flexible + SH7780 earlyprintk SCIF support.
sh: Fixup various PAGE_SIZE == 4096 assumptions.
sh: Fixup 4K irq stacks.
sh: dma-api channel capability extensions.
sh: Drop name overload in dma-sh.
sh: Make dma-isa depend on ISA_DMA_API.
...
* git://git.infradead.org/users/dhowells/workq-2.6:
Actually update the fixed up compile failures.
WorkQueue: Fix up arch-specific work items where possible
WorkStruct: make allyesconfig
WorkStruct: Pass the work_struct pointer instead of context data
WorkStruct: Merge the pending bit into the wq_data pointer
WorkStruct: Typedef the work function prototype
WorkStruct: Separate delayable and non-delayable events.
Adds support for RTCs (through genrtc) for M68KNOMMU.
Board-specific code will have to link the appropriate RTC driver to the
mach_hwclk callback, at minimum.
This patch switches the 68360 code over to using rtc_time.
Signed-off-by: Gavin Lambert <gavinl@compacsort.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 523x timer TRR register is a full 32bits, the older register (on
other ColdFire parts) was only 16 bits. Use the right type of
__raw_read when accessing it.
Problem found by Yaroslav Vinogradov <yaroslav.vinogradov@freescale.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following moves the creation of IPR interupts into setup-7750.c
and updates a few other things to make it all work after the "Drop
CPU subtype IRQ headers" commit. It boots and runs fine on my titan
board.
- adds an ipr_idx to the ipr_data and uses a function in the subtype
code to calculate the address of the IPR registers
- adds a function to enable individual interrupt mode for externals
in the subtype code and calls that from the titan board code
instead of doing it directly.
- I changed the shift in the ipr_data to be the actual # of bits to
shift, instead of the numnber / 4 - made it easier to match with
the manual.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since some header inclusion paths were cleaned up, compilation
broke. Add in the headers we need directly to build again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a platform device for the directly connected
CF interface on R7780RP boards, for use with the
pata_platform libata driver.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds basic NO_IDLE_HZ support to the SH timer API so timers
are able to wire it up. Taken from the ARM version, as it fit in
to our API with very few changes needed.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This syncs up the SH clock framework with the linux/clk.h API,
for which there were only some minor changes required, namely
the clk_get() dev_id and subsequent callsites.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since all of the sys_timer sources currently do this on their own
within the ->get_offset() path, it's more sensible to just have
the caller take care of it when grabbing xtime_lock. Incidentally,
this is more in line with what others (ie, ARM) are doing already.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously this was using a static pgd shift in the reporting
code, simply flip this to PGDIR_SHIFT which does the right
thing depending on varying PTE magnitudes on the SH-X2 MMU.
While we're at it, and since it's been recently added, use
get_TTB() for fetching the TTB, rather than the open coded
instructions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The end of the store queue bitmap is miscalculated when searching
for a free range in sq_remap(), missing the PAGE_SHIFT shift that's
done in sq_api_init(). This runs in to workloads where we can scan
beyond the end of the bitmap.
Spotted by Paul Jackson:
http://marc.theaimsgroup.com/?l=linux-kernel&m=116493191224097&w
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This makes the early printk support somewhat more flexible,
moving the port definition to a config option, and making the
port initialization configurable for sh-ipl+g users.
At the same time, this allows us to trivially wire up the
SH7780 SCIF0, so that's thrown in too more or less for free.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There were a number of places that made evil PAGE_SIZE == 4k
assumptions that ended up breaking when trying to play with
8k and 64k page sizes, this fixes those up.
The most significant change is the way we load THREAD_SIZE,
previously this was done via:
mov #(THREAD_SIZE >> 8), reg
shll8 reg
to avoid a memory access and allow the immediate load. With
a 64k PAGE_SIZE, we're out of range for the immediate load
size without resorting to special instructions available in
later ISAs (movi20s and so on). The "workaround" for this is
to bump up the shift to 10 and insert a shll2, which gives a
bit more flexibility while still being much cheaper than a
memory access.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was a clobber issue with the register we were saving
the stack in, so we switch to a register that we handle in
the clobber list properly already.
This also follows the x86 changes for allowing the softirq
checks from hardirq context.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This extends the SH DMA API for allowing handling of DMA
channels based off of their respective capabilities.
A couple of functions are added to the existing API,
the core bits are register_chan_caps() for registering
channel capabilities, and request_dma_bycap() for fetching
a channel dynamically based off of a capability set.
Signed-off-by: Mark Glaisher <mark.glaisher@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pass along the dev_id from request_dma() all the way down,
rather than inserting an artificial name relating to the TEI
line that we were doing before.
This makes the line a bit less obvious, but dev_id is the proper
behaviour for this regardless.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously we linked in the ISA DMA wrapper unconditionally.
As there are very few users of this, it's better to make it
conditional.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Handle the case where no registered DMACs exist somewhat more
gracefully. While we're at it, check for sysdev_create_file()
failing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The implementation of system call tracing in the kernel has a
couple of ordering problems:
- the validity of the system call number is checked before
calling out to system call tracing code, and should be
done after
- the system call number used when tracing is the one the
system call was invoked with, while the system call tracing
code can legitimatly change the call number (for example
strace permutes fork into clone)
This patch fixes both of these problems, and also reoders the
code slightly to make the direct path through the code the
common case.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Handle simple TLB miss faults which can be resolved completely
from the page table in assembler.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for a generic push switch framework. Adaptable for
various switches, including GPIO switches and the push switches commonly
found on Renesas debug boards.
This allows switch states to be trivially reported through sysfs.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove extra bits from the pmd structure and store a kernel logical
address rather than a physical address. This allows it to be directly
dereferenced. Another piece of wierdness inherited from x86.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add TTB accessor functions and give it a sensible default
value. We will use this later for optimizing the fault
path.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove the previous saving of fault codes into the thread_struct
as they are never used, and appeared to be inherited from x86.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the kernel for gcc4. The existing exception handlers
needed some wrapping for pt_regs access, acessing the registers
via a RELOC_HIDE() pointer.
The strcpy() issues popped up here too, so add -ffreestanding and
kill off the symbol export.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously big endian was simply assumed if little endian was
not set, which led to some cflags ordering issues. There's not
much point to not having a big endian option, so shove one in
a choice and wire it up in the Makefile.
This lets us clean up some of the cflags ordering while we're
at it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds some preliminary support for the SH-X2 MMU, used by
newer SH-4A parts (particularly SH7785).
This MMU implements a 'compat' mode with SH-X MMUs and an
'extended' mode for SH-X2 extended features. Extended features
include additional page sizes (8kB, 4MB, 64MB), as well as the
addition of page execute permissions.
The extended mode attributes are placed in a second data array,
which requires us to switch to 64-bit PTEs when in X2 mode.
With the addition of the exec perms, we also overhaul the mmap
prots somewhat, now that it's possible to handle them more
intelligently.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This drops the various IRQ headers that were floating around
and primarily providing hardcoded IRQ definitions for the
various CPU subtypes. This quickly got to be an unmaintainable
mess, made even more evident by the subtle breakage introduced
by the SH-2 and SH-2A changes.
Now that subtypes are able to register IRQ maps directly, just
rip all of the headers out.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the various CPU subtypes currently hardcode TIMER_IRQ,
switch this to a config option in the few places we need this.
This allows further removal of hardcoded IRQ headers..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the Solution Engine 7206 and 7619.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits out common bits from the existing exception handler for
use between SH-2/SH-2A and SH-3/4, and adds support for the SH-2/2A
exceptions.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-2A has special division hardware as opposed to a full-fledged FPU,
wire up the exception handlers for this.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements initial support for the SH7206 (SH-2A) and SH7619
(SH-2) MMU-less CPUs.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix up arch-specific work items where possible to use the new work_struct and
delayed_work structs.
Three places that enqueue bits of their stack and then return have been marked
with #error as this is not permitted.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
* master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc: (194 commits)
[POWERPC] Add missing EXPORTS for mpc52xx support
[POWERPC] Remove obsolete PPC_52xx and update CLASSIC32 comment
[POWERPC] ps3: add a default zImage target
[POWERPC] Add of_platform_bus support to mpc52xx psc uart driver
[POWERPC] typo fix and whitespace cleanup on mpc52xx-uart driver
[POWERPC] Fix debug printks for 32-bit resources in the PCI code
[POWERPC] Replace kmalloc+memset with kzalloc
[POWERPC] Linkstation / kurobox support
[POWERPC] Add the e300c3 core to the CPU table.
[POWERPC] ppc: m48t35 add missing bracket
[POWERPC] iSeries: don't build head_64.o unnecessarily
[POWERPC] iSeries: stop dt_mod.o being rebuilt unnecessarily
[POWERPC] Fix cputable.h for combined build
[POWERPC] Allow CONFIG_BOOTX_TEXT on iSeries
[POWERPC] Allow xmon to build on legacy iSeries
[POWERPC] Change ppc64_defconfig to use AUTOFS_V4 not V3
[POWERPC] Tell firmware we can handle POWER6 compatible mode
[POWERPC] Clean images in arch/powerpc/boot
[POWERPC] Fix OF pci flags parsing
[POWERPC] defconfig for lite5200 board
...
The support for the 52xx-based systems is now included under
CONFIG_CLASSIC32, since the 52xx chips have a 603e-based core.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a powerpc make target that can be loaded by the ps3 bootloader (kboot) and
set this as the default image to build for that platform.
Until the compressed zImage wrapper is made, this arranges for a stripped
vmlinux image to be built.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32-bit version and 64-bit version are almost equal. Unify them. This
makes further improvements (for example, copying with parallel, supporting
PREFETCH, etc.) easier.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a fix for a typo repeated several times in #error directives for
invalid SiByte configurations.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (34 commits)
[S390] Don't use small stacks when lockdep is used.
[S390] cio: Use device_reprobe() instead of bus_rescan_devices().
[S390] cio: Retry internal operations after vary off.
[S390] cio: Use path verification for last path gone after vary off.
[S390] non-unique constant/macro identifiers.
[S390] Memory detection fixes.
[S390] cio: Make ccw_dev_id_is_equal() more robust.
[S390] Convert extmem spin_lock into a mutex.
[S390] set KBUILD_IMAGE.
[S390] lockdep: show held locks when showing a stackdump
[S390] Add dynamic size check for usercopy functions.
[S390] Use diag260 for memory size detection.
[S390] pfault code cleanup.
[S390] Cleanup memory_chunk array usage.
[S390] Misaligned wait PSW at memory detection.
[S390] cpu shutdown rework
[S390] cpcmd <-> __cpcmd calling issues
[S390] Bad kexec control page allocation.
[S390] Reset infrastructure for re-IPL.
[S390] Some documentation typos.
...
Remove use of __rom_end symbol all together. This helps clean out the
miscellaneous symbols lying around in the m68knommu linker script.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is a small patch to automatically detect the DRAM size on m520x.
It was generated against 2.6.17-uc0, and tested on an Intec 5208 dev board.
Signed-off-by: Michael Broughton <mbobowik@telusplanet.net>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out SHMAT, SHMDT, SHMGET and SHMCTL support in sys_ipc() for
m68knommu in 2.6 kernel(uClinux-dist-20060803 release) is missing.
(copied from m68k sources, report by David Wu <davidwu@arcturusnetworks.com>)
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes the following compile error with
CONFIG_BLK_DEV_INITRD=n and -Werror-implicit-function-declaration:
...
CC arch/m68knommu/kernel/setup.o
/home/bunk/linux/kernel-2.6/linux-2.6.18-rc5-mm1/arch/m68knommu/kernel/setup.c: In function 'setup_arch':
/home/bunk/linux/kernel-2.6/linux-2.6.18-rc5-mm1/arch/m68knommu/kernel/setup.c:268: error: implicit declaration of function 'paging_init'
make[2]: *** [arch/m68knommu/kernel/setup.o] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The lock dependency validator adds a bunch of extra stack frames to
the stack, which can cause stack overflows. Especially seen on 31 bit
where the small stack is only 4k.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
VMALLOC_END on 31bit should be 0x8000000UL instead of 0x7fffffffL.
The page mask which is used to make sure memory_end is on 4MB/2MB
boundary is wrong and not needed. Therefore remove it.
Make sure a vmalloc area does also exist and work on (future)
machines with 4TB and more memory.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There's no need to have a spin_lock here, but need sleepable context
for vmem_map. Therefore convert the spin_lock into a mutex.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Set KBUILD_IMAGE to a sane value. This enables "make rpm"
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Follow i386/x86_64:
lockdep can be used to print held locks when printing a
backtrace. This can be useful when debugging things like
'scheduling while atomic' asserts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use a wrapper for copy_to/from_user to chose the best usercopy method.
The mvcos instruction is better for sizes greater than 256 bytes, if
mvcos is not available a page table walk is better for sizes greater
than 1024 bytes. Also removed the redundant copy_to/from_user_std_small
functions.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Avoid the tprot loop if diag260 works and reports that there are no
holes in memory. The tprot instruction can lead to a significant delay
in the ipl process if the virtual guest has a lot of memory and the
host is under memory pressure.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Need this at yet another file and don't want to add yet another
extern...
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the memory detection code would ever reach the point where it would
load the wait psw, it would generate a specification exception and the
system would crash at ipl time. This is because of a misaligned wait
psw. It needs to be on a double word boundary instead of a word
boundary.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let one master cpu kill all other cpus instead of sending an external
interrupt to all other cpus so they can kill themselves.
Simplifies reipl/shutdown functions a lot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of reipl cpcmd gets called when all other cpus are not running
anymore. To prevent deadlocks change __cpcmd so that it doesn't take
any locks and call cpcmd or __cpcmd, whatever is correct in the current
context.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of re-IPL and diag308 doesn't work we have to reset all devices
manually and wait synchronously that each reset finished.
This patch adds the necessary infrastucture and the first exploiter of it.
Subsystems that need to add a function that needs to be called at re-IPL
may register/unregister this function via
struct reset_call {
struct reset_call *next;
void (*fn)(void);
};
void register_reset_call(struct reset_call *reset);
void unregister_reset_call(struct reset_call *reset);
When the registered function get called the context is:
- all cpus beside the current one are stopped
- all machine checks and interrupts are disabled
- prefixing is disabled
- a default machine check handler is available for use
The registered functions may not take any locks are sleep.
For the common I/O layer part of this patch:
Introduce a reset_call css_reset that does the following:
- clear all subchannels
- perform a rchp on all channel paths and wait for the resulting
machine checks
This replaces the calls to clear_all_subchannels() and
cio_reset_channel_paths() for kexec and ccw reipl. reipl_ccw_dev() now
uses reipl_find_schid() to determine the subchannel id for a given
device id.
Also remove cio_reset_channel_paths() and friends since they are not
needed anymore.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
segment save will exit with a lock held if the passed segment doesn't
exist. Any subsequent call to segment_save will lead to a deadlock.
Fix this and give up the lock before returning.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since the diag 308 reipl method is superior to the ccw method, we should
use it whenever it is possible. We can do that, if the user has not
specified a new reipl ccw device and the system has been ipled from
a ccw device.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If reboot fails (e.g. because wrong devno has been specified by the user),
we should just stop all cpus, but should not trigger a kernel panic.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If multiple kernel images are installed on one DASD, the loadparm can be used
to select the boot configuration. This patch introduces the following two new
sysfs attributes:
/sys/firmware/ipl/loadparm: shows loadparm of current system (ro)
/sys/firmware/reipl/ccw/loadparm: loadparm used for next reboot (rw)
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The SALIPL entry point has an needless memory detection routine as we
later check the memory size again. The SALIPL code also uses diagnose
0x060 if we are running under VM, but this diagnose is not compatible
with the 64 bit addressing mode. The solution is to get rid of this
code and rely on the memory detection in the startup code.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace the 'is_b' variable with 'slot_b' in at91_mmc_data.
Also add the new 'chipselect' variable for CF/PCMCIA and 'bus_width_16'
variable for NAND.
This (and previous patches) will unfortunately break the current MMC,
USB Gadget and PCMCIA drivers. Updates and fixes for those drivers will
be submitted to the various subsystem maintainers.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cure the damage done by the former PCI debug printks fix for the case
of 64-bit resources (commit 685143ac1f)
which broke it for the plain vanilla 32-bit resources...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the Kurobox(HG)/LinkStation-I NAS systems by Buffalo
Technology, should be also applicable to the PPC TeraStation family.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove CPU_FTR_16M_PAGE from the cupfeatures mask at runtime on iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
xmon still does not run on iSeries, but this allows us to build a combined
kernel that includes it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Defconfig ppc64 kernels running under late-model distros
may hang in the automounter rc.d script, which seems to be
expecting autofs version 4. This patch uses the newer autofs.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the "logical" PVR value used by POWER6 in "compatible" mode
to the list of PVR values that the kernel tells firmware it is able to
handle.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a rule to clean up the various generated image files in
arch/powerpc/boot.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For PCI devices with only io ports, of_bus_pci_get_flags() will fall
through and still mark the resource as IORESOURCE_MEM.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds utility routines used by 52xx device drivers and board support
code. Main functionality is to add device nodes to the of_platform_bus,
retrieve the IPB bus frequency, and find+ioremap device registers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is no need to expose these settings outside the scope
of the interrupt controller code itself.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Efika board isn't different enough from other 52xx based boards to
justify a separate platform. This patch merges it with the support
code for all other 52xx based boards.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
platforms/embedded6xx is probably going away, and 52xx boards need
some extra support the 52xx interrupt controller and DMA engine
anyway. It makes sense to group all the 52xx bits into a single path.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
No other chips use this device, it belongs in a 52xx-specific path.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It doesn't hurt to have this enabled on legacy iSeries and will mean it
is available for a combined build.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 3ccfc65c50 missed the same fixes for
legacy iSeries specific code, so make some more symbols no longer global.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Mostly taken from corresponding Makefile's make-clean rule.
Tested by (cross)compiling for $ARCH PPC and POWERPC and checking
output of git-status.
Signed-off-by: Rutger Nijlunsing <git-commit@tux.tmfweb.nl>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds support for flash device descriptions to the OF device tree.
It's inspired by and partially borrowed from Sergei's patch "[RFC]
Adding MTD to device tree.patch".
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows any secondary CPU thread also to become boot cpu for
POWER5. The patch is required to solve kdump boot issue when the
kdump kernel is booted with parameter "maxcpus=1". XICS init code
tries to match the current boot cpu id with "reg" property in each CPU
node in the device tree. But CPU node is created only for primary
thread CPU ids and "reg" property only reflects primary CPU ids. So
when a kernel is booted on a secondary cpu thread above condition will
never meet and the default distribution server is left as zero. This
leads to route the interrupts to CPU 0, but which is not online at
this time.
We use ibm,ppc-interrupt-server#s to check for both primary and
secondary CPU ids. Accordingly default distribution server value is
initialized from "ibm,ppc-interrupt-gserver#s" property. We loop
through ibm,ppc-interrupt-gserver#s property to find the global
distribution server from the last entry that matches with boot cpuid.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It's currently not possible to build the default zImage
target if PS3 is the only selected platform. This is
a hack to fall back to building the pseries style
zImage, so the build is successful. This will probably
change in the future, if someone writes a PS3 specific
boot wrapper.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
A few code paths need to check whether or not they are running
on the PS3's LV1 hypervisor before making hcalls. This introduces
a new firmware feature bit for this, FW_FEATURE_PS3_LV1.
Now when both PS3 and IBM_CELL_BLADE are enabled, but not PSERIES,
FW_FEATURE_PS3_LV1 and FW_FEATURE_LPAR get enabled at compile time,
which is a bug. The same problem can also happen for (PPC_ISERIES &&
!PPC_PSERIES && PPC_SOMETHING_ELSE). In order to solve this, I
introduce a new CONFIG_PPC_NATIVE option that is set when at least
one platform is selected that can run without a hypervisor and then
turns the firmware feature check into a run-time option.
The new cell oprofile support that was recently merged does not
work on hypervisor based platforms like the PS3, therefore make
it depend on PPC_CELL_NATIVE instead of PPC_CELL. This may change
if we get oprofile support for PS3.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
When renaming CONFIG_PS3 to CONFIG_PPC_PS3, a few occurrences have been
missed.
I also fixed up the alignment in arch/powerpc/platforms/Makefile.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
It may be desireable to build a kernel for cell without
spufs, e.g. as the initial kboot kernel. This requires
that the SPU specific parts of the core dump and the xmon
code depend on CONFIG_SPU_BASE instead of CONFIG_PPC_CELL.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Currently, we only send a sigtrap if the current task is being ptraced.
This is somewhat inconsistant, and it breaks utrace support in fedora.
Removing the check should do the right thing in all cases.
Cc: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This changes the spu_create system call to return an error (-ENODEV) if
and isolated spu context is requested on hardware that doesn't support
isolated mode.
Tested on systemsim with and without isolation support
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch fixes a compile issue for the Efika platform recently
introduced by API changes.
Signed-off-by: Nicolas DET <nd@bplan-gmbh.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the oprofile_cpu_type in cputables.c to be ppc64/970MP. Oprofile
needs to distinquish the MP from other 970 processors so it can add some
new counters specific to the 970MP.
Signed-off-by: Mike Wolf <mjw@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the common cell kernel, I want to have ps3 enabled
to find potential bugs at compile-time.
Also enable SPU disassembly in xmon.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds a ps3_defconfig for the PS3 game console.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds spu support for the PS3 platform.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds support for early access to the parameter data from the PS3 'Other OS'
flash memory area. The parameter data mainly holds user preferences like
static ip address.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds some needed bits for a config option PS3_USE_LPAR_ADDR that disables
the PS3 lpar address translation mechanism. This is a currently needed
workaround for limitations in the design of the generic cell spu support.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds the core platform support for the PS3 game console and other devices
using the PS3 hypervisor.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This fixes the xmon support for the cell spu to be compatable with the split
spu platform code.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This adds a platform specific spu management abstraction and the coresponding
routines to support the IBM Cell Blade. It also removes the hypervisor only
resources that were included in struct spu.
Three new platform specific routines are introduced, spu_enumerate_spus(),
spu_create_spu() and spu_destroy_spu(). The underlying design uses a new
type, struct spu_management_ops, to hold function pointers that the platform
setup code is expected to initialize to instances appropriate to that platform.
For the IBM Cell Blade support, I put the hypervisor only resources that were
in struct spu into a platform specific data structure struct spu_pdata.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This includes:
* version 1.24 of ppc-dis.c
* version 1.88 of ppc-opc.c
* version 1.23 of ppc.h
I can't vouch for the accuracy etc. of these changes, but it brings
us into line with binutils - and from a cursory test appears to work
fine.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
While adding spu disassembly support it struck me that we're actually
carrying quite a lot of code around, just to do disassembly in the case
of a crash.
While on large systems it's not an issue, on smaller ones it might be
nice to have xmon - but without the weight of the disassembly support.
For a Cell build this saves ~230KB (!), and for pSeries ~195KB.
We still support the 'di' and 'sdi' commands, however they just dump
the instruction in hex.
Move the definitions into a header to clean xmon.c just a tiny bit.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds a "sdi" command to xmon, to disassemble the contents
of an spu's local store.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch imports and munges the spu disassembly code from binutils.
All files originated from version 1.1 in binutils cvs.
* spu.h, spu-insns.h and spu-opc.c are unchanged except for pathnames.
* spu-dis.c has been edited heavily:
* use printf instead of info->fprintf_func and similar.
* pass the instruction in rather than reading it.
* we have no equivalent to symbol_at_address_func, so we just assume
there is never a symbol at the address given.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
In order to do disassembly of spu binaries in xmon, we need to abstract
the disassembly function from ppc_inst_dump.
We do this by making the actual disassembly function a function pointer
that we pass to ppc_inst_dump(). To save updating all the callers, we
turn ppc_inst_dump() into generic_inst_dump() and make ppc_inst_dump()
a wrapper which always uses print_insn_powerpc().
Currently we pass the dialect into print_insn_powerpc(), but we always
pass 0 - so just make it a local.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Add a command to xmon to dump the memory of a spu's local store.
This mimics the 'd' command which dumps regular memory, but does
a little hand holding by taking the user supplied address and
finding that offset in the local store for the specified spu.
This makes it easy for example to look at what was executing on a spu:
1:mon> ss
...
Stopped spu 04 (was running)
...
1:mon> sf 4
Dumping spu fields at address c0000000019e0a00:
...
problem->spu_npc_RW = 0x228
...
1:mon> sd 4 0x228
d000080080318228 01a00c021cffc408 4020007f217ff488 |........@ ..!...|
Aha, 01a00c02, which is of course rdch $2,$ch24 !
--
Updated to only do the setjmp goo around the spu access, and not
around prdump because it does its own (via mread).
Also the num variable is now common between sf and sd, so you don't
have to keep typing the spu number in if you're repeating commands
on the same spu.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
After stopping spus in xmon I often find myself trawling through the
field dumps to find out which spus were running. The spu stopping
code actually knows what's running, so let's print it out to save
the user some futzing.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
My patch to add spu helpers to xmon (a898497088)
introduced a few sparse warnings, because I was dereferencing an __iomem
pointer.
I think the best way to handle it is to actually use the appropriate in_beXX
functions. Need to rejigger the DUMP macro a little to accomodate that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
With soft-disabled interrupts in power_save, we can
still get external exceptions on Cell, even if we are
in pause(0) a.k.a. sleep state.
When the CPU really wakes up through the 0x100 (system reset)
vector, while we have already started processing the 0x500
(external) exception, we get a panic in unrecoverable_exception()
because of the lost state.
This occurred in Systemsim for Cell, but as far as I can see,
it can theoretically occur on any machine that uses the
system reset exception to get out of sleep state.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds SPU elf notes to the coredump. It creates a separate note
for each of /regs, /fpcr, /lslr, /decr, /decr_status, /mem, /signal1,
/signal1_type, /signal2, /signal2_type, /event_mask, /event_status,
/mbox_info, /ibox_info, /wbox_info, /dma_info, /proxydma_info, /object-id.
A new macro, ARCH_HAVE_EXTRA_NOTES, was created for architectures to
specify they have extra elf core notes.
A new macro, ELF_CORE_EXTRA_NOTES_SIZE, was created so the size of the
additional notes could be calculated and added to the notes phdr entry.
A new macro, ELF_CORE_WRITE_EXTRA_NOTES, was created so the new notes
would be written after the existing notes.
The SPU coredump code resides in spufs. Stub functions are provided in the
kernel which are hooked into the spufs code which does the actual work via
register_arch_coredump_calls().
A new set of __spufs_<file>_read/get() functions was provided to allow the
coredump code to read from the spufs files without having to lock the
SPU context for each file read from.
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Devices with no "reg" nor "dcr-reg" property are given a bus_id which
is the node name alone. This means that if more than one such device
with the same names are present in the system, sysfs will have
collisions when creating the symlinks and will fail registering the
devices.
This works around that problem by assigning successive numbers to such
devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds code to look at the properties firmware puts in the device
tree to determine what compatibility mode the partition is in on
POWER6 machines, and set the ELF aux vector AT_HWCAP and AT_PLATFORM
entries appropriately.
Specifically, we look at the cpu-version property in the cpu node(s).
If that contains a "logical" PVR value (of the form 0x0f00000x), we
call identify_cpu again with this PVR value. A value of 0x0f000001
indicates the partition is in POWER5+ compatibility mode, and a value
of 0x0f000002 indicates "POWER6 architected" mode, with various
extensions disabled. We also look for various other properties:
ibm,dfp, ibm,purr and ibm,spurr.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PPU event-based and cycle-based profiling support to Oprofile for Cell.
Oprofile is expected to collect data on all CPUs simultaneously.
However, there is one set of performance counters per node. There are
two hardware threads or virtual CPUs on each node. Hence, OProfile must
multiplex in time the performance counter collection on the two virtual
CPUs.
The multiplexing of the performance counters is done by a virtual
counter routine. Initially, the counters are configured to collect data
on the even CPUs in the system, one CPU per node. In order to capture
the PC for the virtual CPU when the performance counter interrupt occurs
(the specified number of events between samples has occurred), the even
processors are configured to handle the performance counter interrupts
for their node. The virtual counter routine is called via a kernel
timer after the virtual sample time. The routine stops the counters,
saves the current counts, loads the last counts for the other virtual
CPU on the node, sets interrupts to be handled by the other virtual CPU
and restarts the counters, the virtual timer routine is scheduled to run
again. The virtual sample time is kept relatively small to make sure
sampling occurs on both CPUs on the node with a relatively small
granularity. Whenever the counters overflow, the performance counter
interrupt is called to collect the PC for the CPU where data is being
collected.
The oprofile driver relies on a firmware RTAS call to setup the debug bus
to route the desired signals to the performance counter hardware to be
counted. The RTAS call must set the routing registers appropriately in
each of the islands to pass the signals down the debug bus as well as
routing the signals from a particular island onto the bus. There is a
second firmware RTAS call to reset the debug bus to the non pass thru
state when the counters are not in use.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following routines are added to arch/powerpc/platforms/cell/pmu.c:
cbe_clear_pm_interrupts()
cbe_enable_pm_interrupts()
cbe_disable_pm_interrupts()
cbe_query_pm_interrupts()
cbe_pm_irq()
cbe_init_pm_irq()
This also adds a routine in arch/powerpc/platforms/cell/interrupt.c and
some macros in cbe_regs.h to manipulate the IIC_IR register:
iic_set_interrupt_routing()
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move some PMU-related macros and function prototypes from cbe_regs.h
and pmu.h in arch/powerpc/platforms/cell/ to a new header at
include/asm-powerpc/cell-pmu.h
This is cleaner to use from the oprofile code, since that sits in
arch/powerpc/oprofile, not in the cell platform directory.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
More macros for manipulating bits in the Cell PMU control registers.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add symbol-exports for the new routines in arch/powerpc/platforms/cell/pmu.c.
They are needed for Oprofile, which can be built as a module.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In order to fit with the "don't-run-spus-outside-of-spu_run" model, this
patch starts the isolated-mode loader in spu_run, rather than
spu_create. If spu_run is passed an isolated-mode context that isn't in
isolated mode state, it will run the loader.
This fixes potential races with the isolated SPE app doing a
stop-and-signal before the PPE has called spu_run: bugzilla #29111.
Also (in conjunction with a mambo patch), this addresses #28565, as we
always set the runcntrl register when entering spu_run.
It is up to libspe to ensure that isolated-mode apps are cleaned up
after running to completion - ie, put the app through the "ISOLATE EXIT"
state (see Ch11 of the CBEA).
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This change adds a read accessor for the SPE problem-state run control
register.
This is required for for applying (userspace) changes made to the run
control register while the SPE is stopped - simply asserting the master
run control bit is not sufficient. My next patch for isolated-mode
setup requires this.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When the user changes the runcontrol register, an SPU might be
running without a process being attached to it and waiting for
events. In order to prevent this, make sure we always disable
the priv1 master control when we're not inside of spu_run.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When fixing spufs to map the 'mem' file backing store cacheable,
I incorrectly set the physical mapping to use both cache-inhibited
and guarded mapping, which resulted in a serious performance
degradation.
Debugged-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When one of the spufs files is mapped into a process address
space, regular users can use ptrace to attempt accessing
them with access_process_vm(). With the way that the
mappings currently work, this likely causes an oops.
Setting the vm_flags to VM_IO makes sure that ptrace can
not access them but returns an error code. This is not
the perfect solution in case of the local store mapping,
but it fixes the oops in a well-defined way.
Also remove leftover VM_RESERVED flags in spufs. The
VM_RESERVED flag is on it's way out and not checked by
the memory managment code anymore.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Christoph Hellwig <chellwig@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When there is pending signals, current spufs_run_spu() always returns
-ERESTARTSYS and it is called again automatically.
But, if spe already stopped by stop-and-signal or halt instruction,
returning -ERESTARTSYS makes stop-and-signal/halt lost and
spu run over the end-point.
For your convenience, I attached a sample code to restage this bug.
If there is no bug, printed NPC will be 0x4000.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we attempt an MFC DMA to an unmapped address, the event
returned from spu_run should be SPE_EVENT_SPE_DATA_STORAGE,
not SPE_EVENT_INVALID_DMA.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace the use of the platform specific variable spu.nid with the
platform independednt variable spu.node.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to check the channel count of the signal notification registers
before reading them, because it can be undefined when the count is
zero. In order to read count and data atomically, we read from the
saved context.
This patch uses spu_acquire_saved() to force a context save before a
/signal1 or /signal2 read. Because of this it is no longer necessary to
have backing_ops and hw_ops versions of this function so they have been
removed.
Regular applications should not rely on reading this register
to be fast, as it's conceptually a write-only file from the PPE
perspective.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch implements read only access to
/mbox_info - SPU Write Outbound Mailbox
/ibox_info - SPU Write Outbound Interrupt Mailbox
/wbox_info - SPU Read Inbound Mailbox
These files are used by gdb in order to look into the current mailbox
queues without changing the contents at the same time. They are
not meant for general programming use, since the access requires
a context save and is therefore rather slow.
It would be good to complement this patch with one that adds
write support as well.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes the /spu_tag_mask file from spufs. The data provided by
this file is also available from the /dma_info file in the dma_info_mask
of the spu_dma_info struct.
The file was intended to be used by gdb, but that never used it, and
now it has been replaced with the more verbose dma_info file.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The /lslr file gives read access to the SPU_LSLR register in hex; 0x3fff
for example The /dma_info file provides read access to the SPU Command
Queue in a binary format. The /proxydma_info files provides read access
access to the Proxy Command Queue in a binary format. The spu_info.h
file provides data structures for interpreting the binary format of
/dma_info and /proxydma_info.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patches changes /npc, /decr, /decr_status, /spu_tag_mask,
/event_mask, /event_status, and /srr0 files to provide output according to
the format string "0x%llx" instead of "%llx".
Before this patch some files used "0x%llx" and other used "%llx" which is
inconsistent and potentially confusing. A user might assume "%llx" numbers
were decimal if they happened to not contain any a-f digits. This change
will break any code cannot tolerate a leading 0x in the file contents. The
only known users of these files are the libspe but there might also be
some scripts which access these files. This risk is deemed acceptable for
future consistency.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SCC parameter RAM areas are mapped wrong in MPC8xx device descriptions. All
memory areas overlap with the next one, so that I2C, SPI, SMC1 and SMC2 cannot
be enabled if the four SCCs are.
Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/sysdev/mpc52xx_pic.c breaks the ppc build
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch below fixes an arithmetic wrap-around issue on 32bit machines
using smp-tbsync. Without this patch a timebase value over
0x000000007fffffff will hang the boot process while bringing up
secondary CPUs.
Signed-off-by: Adrian Cox <adrian@humboldt.co.uk>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes 2 changes to clean up the flat device tree handling
logic in the zImage wrapper.
First, there were two callbacks from the dt_ops structure used for
producing a final flat tree to pass to the kerne: dt_ops.ft_pack()
which packed the flat tree (possibly a no-op) and dt_ops.ft_addr()
which retreived the address of the final blob. Since they were only
ever called together, this patch combines the two into a single new
callback, dt_ops.finalize(). This new callback does whatever
platform-dependent things are necessary to produce a final flat device
tree blob, and returns the blob's addres.
Second, the current logic calls the kernel with a flat device tree if
one is build into the zImage wrapper, otherwise it boots the kernel
with a PROM pointer, expecting the kernel to copy the OF device tree
itself. This approach precludes the possibility of the platform
wrapper code building a flat device tree from whatever
platform-specific information firmware provides. Thus, this patch
takes the more sensible approach of invoking the kernel with a flat
tree if the dt_ops.finalize callback provides one (by whatever means).
So, the dt_ops.finalize callback can be NULL, or can be a function
which returns NULL. In either case, the zImage wrapper logic assumes
that this is a platform with OF and invokes the kernel accordingly.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes the handling of the initrd (or initramfs) in the
zImage wrapper a little easier to follow. Instead of passing the
initrd addresses out from prep_kernel() via the cryptic a1 and a2
parameters, use the global struct add_range, 'initrd'. prep_kernel()
already passes information through the 'vmlinux' addr_range struct, so
this seems like a reasonable extension.
Some comments also clarify the logic with prep_kernel(): we use an
initrd included in the zImage if present, otherwise we use an initrd
passed in by the bootloader in the a1 and a2 parameters (yaboot, at
least, uses this mechanism to pass an initrd).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Per email discussion, it appears that rtas_stop_self()
and pSeries_mach_cpu_die() should not be compiled if
CONFIG_HOTPLUG_CPU is not defined. This patch adds
#ifdefs around these bits of code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch adds a tsi108/9 pci interrupt controller host.
On mpc7448hpc2 board, pci_irq_fixup function is removed, which makes the
pci_read_irq_line be the default pci irq fixup.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix compilation without PCI support for Bubinga, CPCI405 and EP405.
bios_fixup() for these boards uses functions available only with
CONFIG_PCI, so linker fails.
Signed-off-by: Wojtek Kaniewski <wojtekka@toxygen.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PPC/booke reg MCSR value misquoted
Signed-off-by: nkalmala <nkalmala@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rewrite local_get_flags and local_irq_disable to use r13 explicitly,
to avoid the risk that gcc will split get_paca()->soft_enabled into a
sequence unsafe against preemption. Similar care in local_irq_restore.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Merge 32 and 64 bits asm-powerpc/io.h
The rework on io.h done for the new hookable accessors made it easier,
so I just finished the work and merged 32 and 64 bits io.h for arch/powerpc.
arch/ppc still uses the old version in asm-ppc, there is just too much gunk
in there that I really can't be bothered trying to cleanup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In order to suppose platforms with devices above 4Gb on 32 bits platforms
with a >32 bits physical address space, we used to have a special ioremap64
along with a fixup routine fixup_bigphys_addr.
This shouldn't be necessary anymore as struct resource now supports 64 bits
addresses even on 32 bits archs. This patch enables that option when
CONFIG_PHYS_64BIT is set and removes ioremap64 and fixup_bigphys_addr.
This is a preliminary work for the upcoming merge of 32 and 64 bits io.h
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds full cell iommu support (and iommu disabled mode).
It implements mapping/unmapping of iommu pages on demand using the
standard powerpc iommu framework. It also supports running with
iommu disabled for machines with less than 2GB of memory. (The
default is off in that case, though it can be forced on with the
kernel command line option iommu=force).
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that the direct DMA ops supports an offset, we use that instead
of defining our own.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes dma_alloc_coherent() use node local allocation when
using the direct DMA ops. The node is obtained from the new device
extension. If no such extension is present, the current node is used.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds an optional global offset that can be added to DMA addresses
when using the direct DMA operations.
That brings it a step closer to the 32 bits direct DMA operations, and makes
it useable on Cell when the MMU is disabled and we are using a spider
southbridge.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch implements a workaround for a Spider PCI host bridge bug
where it doesn't enforce some of the PCI ordering rules unless some
manual manipulation of a special register is done. In order to be
fully compliant with the PCI spec, I do this on every MMIO read
operation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way iSeries hooks on PCI IO operations (both MMIO
and PIO) and provides a generic way for other platforms to do so (we
have need to do that for various other platforms).
While reworking the IO ops, I ended up doing some spring cleaning in
io.h and eeh.h which I might want to split into 2 or 3 patches (among
others, eeh.h had a lot of useless stuff in it).
A side effect is that EEH for PIO should work now (it used to pass IO
ports down to the eeh address check functions which is bogus).
Also, new are MMIO "repeat" ops, which other archs like ARM already had,
and that we have too now: readsb, readsw, readsl, writesb, writesw,
writesl.
In the long run, I might also make EEH use the hooks instead
of wrapping at the toplevel, which would make things even cleaner and
relegate EEH completely in platforms/iseries, but we have to measure the
performance impact there (though it's really only on MMIO reads)
Since I also need to hook on ioremap, I shuffled the functions a bit
there. I introduced ioremap_flags() to use by drivers who want to pass
explicit flags to ioremap (and it can be hooked). The old __ioremap() is
still there as a low level and cannot be hooked, thus drivers who use it
should migrate unless they know they want the low level version.
The patch "arch provides generic iomap missing accessors" (should be
number 4 in this series) is a pre-requisite to provide full iomap
API support with this patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes the Cell DMA code work on both the Spider and the Axon
south bridges by turning cell_dma_valid into a variable instead of a
constant. This is a temporary patch until we have full iommu support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When enabled in Kconfig, it will pick up any of_platform_device
matching it's match list (currently type "pci", "pcix", "pcie",
or "ht" and setup a PHB for it.
Platform must provide a ppc_md.pci_setup_phb() for it to work
(for doing the necessary initialisations specific to a given PHB
like setting up the config space ops).
It's currently only available on 64 bits as the 32 bits PCI code
can't quite cope with it in it's current form. I will fix that
later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a "parent" struct device to our PCI host bridge data structure so that
PCI can be rooted off another device in sysfs.
Note that arch/ppc doesn't use it, only arch/powerpc, though it's available
for both 32 and 64 bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The BUID is the first entry of a PCI host bridge "reg" property.
Now that PCI busses can be anywhere in the device-tree, we need to
fully translate the value there to a CPU physical address before
we can use it with RTAS.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When parsing the OF "ranges" properties of PCI host busses to determine
the mapping of a PCI bus, we need to translate the "parent" address using
the prom_parse.c routines in order to obtain a CPU physical address.
This wasn't necessary while PCI busses were always at the root of the
device-tree but this is no longer the case on Cell where they can be
anywhere in the tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a bus device notifier to the of_platform bus type on
cell to setup the DMA operations for of_platform_devices. We currently
use the PCI operations as Cell use a special version of them that
happens to be suitable for our needs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch completely refactors DMA operations for 64 bits powerpc. 32 bits
is untouched for now.
We use the new dev_archdata structure to add the dma operations pointer
and associated data to struct device. While at it, we also add the OF node
pointer and numa node. In the future, we might want to look into merging
that with pci_dn as well.
The old vio, pci-iommu and pci-direct DMA ops are gone. They are now replaced
by a set of generic iommu and direct DMA ops (non PCI specific) that can be
used by bus types. The toplevel implementation is now inline.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Hook up of_platform_bus_probe with the cell platform in order to publish
the non-PCI devices in the device-tree of cell blades as of_platform_device(s)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch first splits of_device.c and of_platform.c, the later containing
the bits relative to of_platform_device's. On the "breaks" side of things,
drivers uisng of_platform_device(s) need to include asm/of_platform.h now
and of_(un)register_driver is now of_(un)register_platform_driver.
In addition to a few utility functions to locate of_platform_device(s),
the main new addition is of_platform_bus_probe() which allows the platform
code to trigger an automatic creation of of_platform_devices for a whole
tree of devices.
The function acts based on the type of the various "parent" devices encountered
from a provided root, using either a default known list of bus types that can be
"probed" or a passed-in list. It will only register devices on busses matching
that list, which mean that typically, it will not register PCI devices, as
expected (since they will be picked up by the PCI layer).
This will be used by Cell platforms using 4xx-type IOs in the Axon bridge
and can be used by any embedded-type device as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support for southbridges using the MPIC interrupt controller to
the native cell platforms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch applies on top of the MPIC DCR support. It makes the MPIC
driver capable of a lot more auto-configuration based on the device-tree,
for example, it can retreive it's own physical address if not passed as
an argument, find out if it's DCR or MMIO mapped, and set the BIG_ENDIAN
flag automatically in the presence of a "big-endian" property in the
device-tree node.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch implements support for DCR based MPIC implementations. Such
implementations have the MPIC_USES_DCR flag set and don't use the phys_addr
argument of mpic_alloc (they require a valid dcr mapping in the device node)
This version of the patch can use a little bif of cleanup still (I can
probably consolidate rb->dbase/doff, at least once I'm sure on how the
hardware is actually supposed to work vs. possible simulator issues) and
it should be possible to build a DCR-only version of the driver. I need
to cleanup a bit the CONFIG_* handling for that and probably introduce
CONFIG_MPIC_MMIO and CONFIG_MPIC_DCR.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds new dcr_map/dcr_read/dcr_write accessors for DCRs that
can be used by drivers to transparently address either native DCRs or
memory mapped DCRs. The implementation for memory mapped DCRs is done
after the binding being currently worked on for SLOF and the Axon
chipset. This patch enables it for the cell native platform
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These were inherited from ARCH=ppc, but are not needed since parsing of interrupts
should be done via the of_* functions (who can do swizzling). If we ever need to
do non-standard swizzling on bridges without a device-node, then we might add
back a slightly different version of ppc_md.pci_swizzle but for now, that is not
the case.
I removed the couple of calls for these in 83xx. If that breaks something, then
there is a problem with the device-tree on these.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way IRQs are fixed up on PCI for arch powerpc.
It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().
It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.
I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.
I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
XScale cores either have a DSP coprocessor (which contains a single
40 bit accumulator register), or an iWMMXt coprocessor (which contains
eight 64 bit registers.)
Because of the small amount of state in the DSP coprocessor, access to
the DSP coprocessor (CP0) is always enabled, and DSP context switching
is done unconditionally on every task switch. Access to the iWMMXt
coprocessor (CP0/CP1) is enabled only when an iWMMXt instruction is
first issued, and iWMMXt context switching is done lazily.
CONFIG_IWMMXT is supposed to mean 'the cpu we will be running on will
have iWMMXt support', but boards are supposed to select this config
symbol by hand, and at least one pxa27x board doesn't get this right,
so on that board, proc-xscale.S will incorrectly assume that we have a
DSP coprocessor, enable CP0 on boot, and we will then only save the
first iWMMXt register (wR0) on context switches, which is Bad.
This patch redefines CONFIG_IWMMXT as 'the cpu we will be running on
might have iWMMXt support, and we will enable iWMMXt context switching
if it does.' This means that with this patch, running a CONFIG_IWMMXT=n
kernel on an iWMMXt-capable CPU will no longer potentially corrupt iWMMXt
state over context switches, and running a CONFIG_IWMMXT=y kernel on a
non-iWMMXt capable CPU will still do DSP context save/restore.
These changes should make iWMMXt work on PXA3xx, and as a side effect,
enable proper acc0 save/restore on non-iWMMXt capable xsc3 cores such
as IOP13xx and IXP23xx (which will not have CONFIG_CPU_XSCALE defined),
as well as setting and using HWCAP_IWMMXT properly.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* sanitize prototypes, annotate
* usual ntohs->shift
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes, annotate
* collapse csum_partial_copy
* usual ntohs->shift
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes, annotate
* kill csum_partial_copy_fromuser
* kill shift-by-16 in checksum calculations
* ntohs->shift in checksum calculations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes, annotate
* collapse csum_partial_copy
* kill csum_partial_copy_fromuser
* ntohs->shift in checksum calculation
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitized prototypes, annotated
* kill shift-by-16 in checksum calculation
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes, annotate
* kill shift-by-16 in checksum calculations
* htons->shift in l-e checksum calculations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes, annotated
* collapsed csum_partial_copy()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes, annotate
* ntohs -> shift in checksum calculations in l-e case
* kill shift-by-16 in checksum calculations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes, annotate
* ntohs -> shift in checksum calculations
* kill access_ok() in csum_partial_copy_from_user
* collapse do_csum_partial_copy_from_user
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes and annotate
* collapse csum_partial_copy
NB: csum_partial() is almost certainly still buggy.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes and annotate
* collapse csum_partial_copy
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes and annotate
* kill cast-as-lvalue abuses in csum_partial()
* usual ntohs-equals-shift for checksum purposes
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* sanitize prototypes and annotate
* kill useless access_ok() in csum_partial_copy_from_user() (the only
caller checks it already).
* do_csum_partial_copy_from_user() is not needed now
* replace htons(len) with len << 8 - they are the same wrt checksums
on little-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 281ea49b0c,
which broke ACPI Interrupt source overrides that move
the SCI from one IRQ in PIC mode to another in IOAPIC mode.
If the SCI shared an interrupt line with another device,
this would result in a "irq 18: nobody cared" type failure.
http://bugzilla.kernel.org/show_bug.cgi?id=7601
Signed-off-by: Len Brown <len.brown@intel.com>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (31 commits)
[MIPS] Remove duplicate ISA DMA code for 0 DMA channel case.
[MIPS] Remove unused definition of cpu_to_lelongp()
[MIPS] Remove userspace proofing from <asm/bitops.h>.
[MIPS] Remove old junk left from old atomic_lock.
[MIPS] Use conditional traps for BUG_ON on MIPS II and better.
[MIPS] mips HPT cleanup: make clocksource_mips public
[MIPS] do_IRQ cleanup
[MIPS] Avoid dupliate D-cache flush on R400C / R4400 SC and MC variants.
[MIPS] Remove redundant r4k_blast_icache() calls
[MIPS] Work around bogus gcc warnings.
[MIPS] Fix double inclusions
[MIPS] use generic_handle_irq, handle_level_irq, handle_percpu_irq
[MIPS] IRQ cleanups
[MIPS] mips hpt cleanup: get rid of mips_hpt_init
[MIPS] PB1200: Remove duplicate definitions
[MIPS] Fix alignment hole in struct cache_desc; shrink struct.
[MIPS] Oprofile: kernel support for the R10000.
[MIPS] Remove unused R10000 performance counter definitions.
[MIPS] Add support for kexec
[MIPS] Don't print presence of WAIT instruction on bootup.
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
Driver core: show drivers in /sys/module/
Documentation/driver-model/platform.txt update/rewrite
Driver core: platform_driver_probe(), can save codespace
driver core: Use klist_remove() in device_move()
driver core: Introduce device_move(): move a device to a new parent.
Driver core: make drivers/base/core.c:setup_parent() static
driver core: Introduce device_find_child().
sysfs: sysfs_write_file() writes zero terminated data
cpu topology: consider sysfs_create_group return value
Driver core: Call platform_notify_remove later
ACPI: Change ACPI to use dev_archdata instead of firmware_data
Driver core: add dev_archdata to struct device
Driver core: convert sound core to use struct device
Driver core: change mem class_devices to be real devices
Driver core: convert fb code to use struct device
Driver core: convert firmware code to use struct device
Driver core: convert mmc code to use struct device
Driver core: convert ppdev code to use struct device
Driver core: convert PPP code to use struct device
Driver core: convert cpuid code to use struct device
...
Remove BTB_ENABLE from proc-xsc3.S
On some early revisions of xsc3 enabling the branch target buffer can cause
crashes, see erratum #42.
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge L_PTE_COHERENT with L_PTE_SHARED and free up a L_PTE_* bit.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global pci_bf_sort static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updated patch adds the Intel ICH9 LPC and SMBus Controller DID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Tested (compilation only):
- using allmodconfig
- making sure the files are compiling without any warning/error due to
new changes
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mostly CodingStyle cleanups for arch/i386/pci/i386.c:
- fit in 80 columns;
- use a #defined value instead of an inline constant;
Also change one resource_size_t (DBG) printk from %08lx to %lx since
it can be more than 32 bits (more than 8 hexits).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support a shadowed ROM when running with an ACPI capable PROM.
Define a new dev.resource flag IORESOURCE_ROM_BIOS_COPY to
describe the case of a BIOS shadowed ROM, which can then
be used to avoid pci_map_rom() making an unneeded call to
pci_enable_rom().
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
First phase in introducing ACPI support to SN.
In this phase, when running with an ACPI capable PROM,
the DSDT will define the root busses and all SN nodes
(SGIHUB, SGITIO). An ACPI bus driver will be registered
for the node devices, with the acpi_pci_root_driver being
used for the root busses. An ACPI vendor descriptor is
now used to pass platform specific information for both
nodes and busses, eliminating the need for the current
SAL calls. Also, with ACPI support, SN fixup code is no longer
needed to initiate the PCI bus scans, as the acpi_pci_root_driver
does that.
However, to maintain backward compatibility with non-ACPI capable
PROMs, none of the current 'fixup' code can been deleted, though
much restructuring has been done. For example, the bulk of the code
in io_common.c is relocated code that is now common regardless
of what PROM is running, while io_acpi_init.c and io_init.c contain
routines specific to an ACPI or non ACPI capable PROM respectively.
A new pci bus fixup platform vector has been created to provide
a hook for invoking platform specific bus fixup from pcibios_fixup_bus().
The size of io_space[] has been increased to support systems with
large IO configurations.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This file no longer uses pci_cache_line_size, so delete the declaration
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The setting of the CACHE_LINE_SIZE register in sparc64's pci
initialisation code isn't quite adequate as the device may have
incompatible requirements. The generic code tests for this, so switch
sparc64 over to using it.
Since sparc64 has different L1 cache line size and PCI cache line size,
it would need to override the generic code like i386 and ia64 do. We
know what the cache line size is at compile time though, so introduce a
new optional constant PCI_CACHE_LINE_BYTES.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pci_generic_prep_mwi() code does everything that pcibios_prep_mwi()
does on ia64. All we need to do is be sure that pci_cache_line_size
is set appropriately, and we can delete pcibios_prep_mwi().
Using SMP_CACHE_BYTES as the default was wrong on uniprocessor machines
as it is only 8 bytes. The default in the generic code of L1_CACHE_BYTES
is at least as good.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The number of permutations of crap we do is amazing and almost all of it
has the wrong effect in 2.6.
At the heart of this is the PCI SFF magic which says that compatibility
mode PCI IDE controllers use ISA IRQ routing and hard coded addresses
not the BAR values. The old quirks variously clears them, sets them,
adjusts them and then IDE ignores the result.
In order to drive all this garbage out and to do it portably we need to
handle the SFF rules directly and properly. Because we know the device
BAR 0-3 are not used in compatibility mode we load them with the values
that are implied (and indeed which many controllers actually
thoughtfully put there in this mode anyway).
This removes special cases in the IDE layer and libata which now knows
that bar 0/1/2/3 always contain the correct address. It means our
resource allocation map is accurate from boot, not "mostly accurate"
after ide is loaded, and it shoots lots of code. There is also lots more
code and magic constant knowledge to shoot once this is in and settled.
Been in my test tree for a while both with drivers/ide and with libata.
Wants some -mm shakedown in case I've missed something dumb or there are
corner cases lurking.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Create include/asm-arm/arch-ixp4xx/udc.h and
add platfrom device ixp4xx_udc_device into
arch/arm/mach-ixp4xx/common.c.
This allows us to use pxa2xx-udc on
the ixp4xx platfrom. Both pxa2xx and
ixp4xx use the same device controller.
Signed-off-by:Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch contains various updates the at91rm9200_devices.c file:
* Consistent naming of resources and platform_devices.
* PCMCIA/Compact Flash: Configuration of the memory controller
moved out of the driver and into this file.
* MMC: Enable the VCC pin (if one is configured)
* MMC: Enable the internal pullups on the I/O pins.
* NAND: Configuration of the memory controller moved out of the
driver and into this file.
* Added TWI/I2C resources.
* The names of some of the CONFIG_ variables were changed.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A number of configuration file changes.
These are mainly to replace references to ARCH_AT91RM9200 and
ARCH_AT91SAM9261 with the common/generic ARCH_AT91. That way we don't
need to mention every specific AT91 processor explicitly.
Also adds the configuration option for AT91SAM9260-EK and AT91SAM9261-EK
boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the Atmel AT91SAM9261-EK board.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the Atmel AT91SAM9260-EK board.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The master abort check in ixp2000_pci_read_config() recently started
failing due to the compiler optimising out the read access following
the clearing of pci_master_aborts. Mark pci_master_aborts volatile to
force the compiler to reload it on every use.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add initial board support for the ADS Sphere board.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch includes a number of small changes for integrating the
AT91SAM9261 and AT91SAM0260 support.
* Can only select support for one AT91 processor at a time.
* Remove most of the remaining static memory mapping for the
AT91RM9200.
* Reserve 1Mb of memory below the IO for mapping the internal SRAM
and any custom board-specific devices (ie, FPGA).
* The SAM9260 has more serial ports, so increase the maximum to 7.
* Define the standard chipselect addresses, and define other
addresses relative to those.
* CLOCK_TICK_RATE is different on the SAM926x's.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The bits used to select the USB clocks are different on the SAM9's.
Add support for the HCK clocks on the AT91SAM9261.
Patch from Patrice Vilchez & Nicolas Ferre
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch converts the old CONFIG_MTD_PHYSMAP_ options to the new
physmap API by creating a physmap platform device for the NOR flash
found on the Atmel AT91RM9200-DK and AT91RM9200-EK boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the Carmeva board support:
* Specify the MMC Write-protect and Detection pins.
* Add configuration of SPI devices.
Patch from Peer Georgi.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Attached is a patch for at91rm9200_time.c which removes
the 'BUG: soft lockup detected on CPU#0!' message when
exiting suspended states.
Patch from Savin Zlobec
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch includes the pin initialization, resource definition and
registration of the platform_devices for the SAM9260 and SAM9261
processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the timer on the Atmel AT91SAM9261 and AT91SAM9260
processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the drivers (and other files) which include the
hardware headers. This fixes the breakage introduced in patches 3950/1
and 3951/1 (those patches were getting big).
The AVR32 architecture uses the same serial driver and had its own copy
of at91rm9200_pdc.h. Renamed it to at91_pdc.h
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the initial support for the newer Atmel AT91SAM9261 and
AT91SAM9260 processors. The code is based on, and makes use of, the
existing AT91RM9200 support.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The external interrupt sources are different on the various AT91
processors. This patch introduces the global 'at91_extern_irq' variable
that contains a bitset of the available external interrupt sources.
The processor reset mechanism also differs on the various AT91
processors. This patch also adds a global 'at91_arch_reset' callback
(from system.h) into the processor-specific code to perform the reset.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch renames the arch/arm/mach-at91rm9200/devices.c file to
at91rm9200_devices.c. The file contains AT91RM9200-specific code, so we
will need separate files for the SAM9 processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no point having the Versatile PB initialisation using an
arch_initcall() and then checking whether it's running on a
Versatile PB board - this is what the .init_machine function
pointer in the machine description is for. Use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove ARM local cache of 4 struct thread_info.
Can cause oops under certain circumstances.
Russell indicated the original optimization was
required on older kernels to avoid thread starvation
on memory fragmentation, but may no longer be
required. I've updated the patch to 19rc4 and
ensured no <config.h> dain-bramage slipped in this
time (sorry about that).
Original description follows:
I was given some test results which pointed to an
Oops in alloc_thread_info (happened 2x), and after
looking at the code, I see that ARM has its own
local cache of 4 struct thread_info. There wasn't
any clear (to me) synchronization between the
alloc_thread_info and the free_thread_info.
I looked over the other arch, and they all simply
allocate them on an as needed basis, so I simplified
the ARM to do the same, based on the other arch
(e.g. PPC) and the folks doing the testing have
indicated that this fixed the oops.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix warnings and errors in arch/arm/mm for nommu build.
Remove commented out function prototype in pgtable-nommu.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't reset OSCR to zero as this prevents us from having a contiguous
time source. The value returned by sched_clock() is reset to zero in the
middle of the boot process otherwise, making CONFIG_PRINTK_TIME rather
messed up.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't reset OSCR to zero as this prevents us from having a contiguous
time source. The value returned by sched_clock() is reset to zero in the
middle of the boot process otherwise, making CONFIG_PRINTK_TIME rather
messed up.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DEBUG_WAITQ appears to have been removed by others, but no one
removed the configuration option from ARM. Remote it from both
Kconfig.debug and all default configurations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These files want to provide/access ELF hwcap information, so should
be including asm/elf.h rather than asm/procinfo.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix an apparant hang with the "apm -s" command. We omitted to wake up
this process once resume had completed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The APM emulation can sometimes cause suspend to fail to work due
to apparantly waiting for some process to acknowledge an event when
it actually has already done so. We re-jig the event handling to
work around this behaviour.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Changes persistant -> persistent. www.dictionary.com does not know
persistant (with an A), but should it be one of those things you can
spell in more than one correct way, let me know.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix various .c/.h typos in comments (no code changes).
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix various Kconfig typos.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Make clocksource_mips public and get rid of mips_hpt_read,
mips_hpt_mask.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now we have both function and macro version of do_IRQ() and the former
is used only by DEC and non-preemptive kernel. This patch makes
everyone use the macro version and removes the function version.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
r4k_flush_cache_all() and r4k_flush_cache_mm() case: these are noop if
the CPU did not have dc_aliases. It would mean we do not need to care
about icache here.
r4k_flush_cache_range case: if r4k_flush_cache_mm() did not need to
care about icache, it would be same for this function.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Further incorporation of generic irq framework. Replacing __do_IRQ()
by proper flow handler would make the irq handling path a bit simpler
and faster.
* use generic_handle_irq() instead of __do_IRQ().
* use handle_level_irq for obvious level-type irq chips.
* use handle_percpu_irq for irqs marked as IRQ_PER_CPU.
* setup .eoi routine for irq chips possibly used with handle_percpu_irq.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a big irq cleanup patch.
* Use set_irq_chip() to register irq_chip.
* Initialize .mask, .unmask, .mask_ack field. Functions for these
method are already exist in most case.
* Do not initialize .startup, .shutdown, .enable, .disable fields if
default routines provided by irq_chip_set_defaults() were suitable.
* Remove redundant irq_desc initializations.
* Remove unnecessary local_irq_save/local_irq_restore, spin_lock.
With this cleanup, it would be easy to switch to slightly lightwait
irq flow handlers (handle_level_irq(), etc.) instead of __do_IRQ().
Though whole this patch is quite large, changes in each irq_chip are
not quite simple. Please review and test on your platform. Thanks.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently nobody outside time.c require mips_hpt_init(). Remove it
and call c0_hpt_timer_init() directly if R4k counter was used for
timer interrupt.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add special short path for emulationg RDHWR which is used to support TLS.
Add an extra prologue for cpu_has_vtag_icache case.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch has rewritten GALILEO_INL/GALILEO_OUTL using GT_READ/GT_WRITE.
This patch tested on Cobalt Qube2.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It allows caller of this function to not care about CKSEG0/XKPHYS
address mixes. It's now automatically done by free_init_pages().
We can now safely remove hack needed by 64 bit kernels with
CONFIG_BUILD_ELF64=n in free_initmem().
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It should fix the broken code in resource_init() too.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
and use new __pa() implementation instead introduced by the previous
patch. Indeed this macro can be used now even by the 64 bit kernels
with CONFIG_BUILD_ELF64=n config.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
__pa() was used by virt_to_page() and virt_addr_valid(). These
latter are used when kernel is initialised so __pa() is not
appropriate, we use virt_to_phys() instead.
Futhermore __pa() is going to take care of CKSEG0/XKPHYS
address mix for 64 bit kernels. This makes __pa() more complex
than virt_to_phys() and this extra work is not needed by
virt_to_page() and virt_addr_valid().
Eventually it consolidates virt_to_phys() prototype by making
its argument 'const'. this avoids some warnings that was due
to some virt_to_page() usages which pass const pointer.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] x86-64: Use stricter in process stack check for unwinder
[PATCH] i386: Fix compilation with UP genericarch
[PATCH] x86-64: Fix warning in io_apic.c
[PATCH] x86-64: work around gcc4 issue with -Os in Dwarf2 stack unwind
[PATCH] x86_64: Align data segment to PAGE_SIZE boundary
Previously it would check for alignment only, which could break
if the stack pointer was unaligned. Now explicitely check if the
stack pointer is in the stack page of the current process.
Ported from i386.
Signed-off-by: Andi Kleen <ak@suse.de>
Commit 2c8c0e6b8d ("[PATCH] Convert x86-64
to early param") broke the earlyprintk=...,keep feature.
This restores that functionality. Tested on x86_64. Must-have for
v2.6.19, no risk.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Eliminate two warnings:
kernel/power/pm.c:205: warning: 'pm_register' is deprecated (declared at kernel/power/pm.c:64)
kernel/power/pm.c:206: warning: 'pm_send_all' is deprecated (declared at kernel/power/pm.c:180)
by updating defconfig files to contain a sensible PM_LEGACY default.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reimplement execvp for our purposes - after we call fork() it is fundamentally
unsafe to use the kernel allocator - current is not valid there. So we simply
pass to our modified execvp() a preallocated buffer. This fixes a real bug
and works very well in testing (I've seen indirectly warning messages from the
forked thread - they went on the pipe connected to its stdout and where read
as a number by UML, when calling read_output(). I verified the obtained
number corresponded to "BUG:").
The added use of __cant_sleep() is not a new bug since __cant_sleep() is
already used in the same function - passing an atomicity parameter would be
better but it would require huge change, stating that this function must not
be called in atomic context and can sleep is a better idea (will make sure of
this gradually).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3941/1: [Jornada7xx] - Addition to MAINTAINERS
[ARM] 3942/1: ARM: comment: consistent_sync should not be called directly
[ARM] ebsa110: fix warnings generated by asm/arch/io.h
[ARM] 3933/1: Source drivers/ata/Kconfig
Removing flush_icache_page a while ago broke SB1 which was using an empty
flush_data_cache_page function. This glues things well enough so a more
efficient but also more intrusive solution can be found later.
Signed-Off-By: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
/*
* Note: Drivers should NOT use this function directly, as it will break
* platforms with CONFIG_DMABOUNCE.
* Use the driver DMA support - see dma-mapping.h (dma_sync_*)
*/
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pass the work_struct pointer to the work function rather than context data.
The work function can use container_of() to work out the data.
For the cases where the container of the work_struct may go away the moment the
pending bit is cleared, it is made possible to defer the release of the
structure by deferring the clearing of the pending bit.
To make this work, an extra flag is introduced into the management side of the
work_struct. This governs auto-release of the structure upon execution.
Ordinarily, the work queue executor would release the work_struct for further
scheduling or deallocation by clearing the pending bit prior to jumping to the
work function. This means that, unless the driver makes some guarantee itself
that the work_struct won't go away, the work function may not access anything
else in the work_struct or its container lest they be deallocated.. This is a
problem if the auxiliary data is taken away (as done by the last patch).
However, if the pending bit is *not* cleared before jumping to the work
function, then the work function *may* access the work_struct and its container
with no problems. But then the work function must itself release the
work_struct by calling work_release().
In most cases, automatic release is fine, so this is the default. Special
initiators exist for the non-auto-release case (ending in _NAR).
Signed-Off-By: David Howells <dhowells@redhat.com>
Separate delayable work items from non-delayable work items be splitting them
into a separate structure (delayed_work), which incorporates a work_struct and
the timer_list removed from work_struct.
The work_struct struct is huge, and this limits it's usefulness. On a 64-bit
architecture it's nearly 100 bytes in size. This reduces that by half for the
non-delayable type of event.
Signed-Off-By: David Howells <dhowells@redhat.com>
mpc832x, as in mpc8360, needs to explicitly find and create the
platform device for ucc_geth in 2.6.19. This code will likely be
readapted to Benh's new of_ methods for 2.6.20.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
o Explicitly align data segment to PAGE_SIZE boundary otherwise depending on
config options and tool chain it might be placed on a non PAGE_SIZE aligned
boundary and vmlinux loaders like kexec fail when they encounter a
PT_LOAD type segment which is not aligned to PAGE_SIZE boundary.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Switch to using irq_handler_t for interrupt function handler pointers.
Change name of m68knommu's irq_hanlder_t data structure so it doesn't
clash with the common type (include/linux/interrupt.h).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is to fix compile error of x86-64 memory hotplug without any NUMA
option.
CC arch/x86_64/mm/init.o
arch/x86_64/mm/init.c:501: error: redefinition of 'memory_add_physaddr_to_nid'
include/linux/memory_hotplug.h:71: error: previous definition of 'memory_add_phys
addr_to_nid' was here
arch/x86_64/mm/init.c:509: error: redefinition of 'memory_add_physaddr_to_nid'
arch/x86_64/mm/init.c:501: error: previous definition of 'memory_add_physaddr_to_
nid' was here
I confirmed compile completion with !NUMA, (NUMA & !ACPI_NUMA),
or (NUMA & ACPI_NUMA).
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Acked-by: Andi Kleen <ak@suse.de>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove two warnings:
drivers/serial/8250_early.c:136: warning: unused variable 'mapsize'
include/linux/io.h:47: warning: passing argument 1 of '__readb' discards qualifiers from pointer target type
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM doesn't source drivers/Kconfig like most architectures do, so the
newly added drivers/ata is currently not made available on ARM. SATA
is used on some ARM machines, like the Thecus N2100, so we need to
source drivers/ata/Kconfig.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When showing the stack backtrace, make sure that we never accept not
only an unchanging frame pointer, but also a frame pointer that moves
back down the stack frame. It must always grow up (toward older stack
frames).
I doubt this has triggered, but a subtly corrupt stack with extremely
unlucky contents could cause us to loop forever on a bogus endless frame
pointer chain.
This review was triggered by much worse problems happening in some of
the other stack unwinding code.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The scheduler on Andreas Friedrich's hyperthreading system stopped
working properly: the scheduler would never move tasks to another CPU!
The lask known working kernel was 2.6.8.
After a couple of attempts to corner the bug, the following smoking gun
was found:
BIOS reported wrong ACPI idfor the processor
CPU#1: set_cpus_allowed(), swapper:1, 3 -> 2
[<c0103bbe>] show_trace_log_lvl+0x34/0x4a
[<c0103ceb>] show_trace+0x2c/0x2e
[<c01045f8>] dump_stack+0x2b/0x2d
[<c0116a77>] set_cpus_allowed+0x52/0xec
[<c0101d86>] cpu_idle_wait+0x2e/0x100
[<c0259c57>] acpi_processor_power_exit+0x45/0x58
[<c0259752>] acpi_processor_remove+0x46/0xea
[<c025c6fb>] acpi_start_single_object+0x47/0x54
[<c025cee5>] acpi_bus_register_driver+0xa4/0xd3
[<c04ab2d7>] acpi_processor_init+0x57/0x77
[<c01004d7>] init+0x146/0x2fd
[<c0103a87>] kernel_thread_helper+0x7/0x10
a quick look at cpu_idle_wait() shows how broken that code is
on i386: it changes the init task's affinity map but never
restores it ...
and because all userspace tasks get forked by init, they all
inherited that single-CPU affinity mask. x86_64 cloned this
bug too.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andreas Friedrich <andreas.friedrich@fujitsu-siemens.com>
Cc: Wolfgang Erig <Wolfgang.Erig@fujitsu-siemens.com>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
the new dwarf2 unwinder crashes while trying to dump the stack:
Leftover inexact backtrace:
Unable to handle kernel paging request at ffffffff82800000 RIP:
[<ffffffff8026cf26>] dump_trace+0x35b/0x3d2
PGD 203027 PUD 205027 PMD 0
Oops: 0000 [2] PREEMPT SMP
CPU 0
Modules linked in:
Pid: 30, comm: khelper Not tainted 2.6.19-rc6-rt1 #11
RIP: 0010:[<ffffffff8026cf26>] [<ffffffff8026cf26>] dump_trace+0x35b/0x3d2
RSP: 0000:ffff81003fb9d848 EFLAGS: 00010006
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff805b3520 RDI: 0000000000000000
RBP: ffffffff827ffff9 R08: ffffffff80aad000 R09: 0000000000000005
R10: ffffffff80aae000 R11: ffffffff8037961b R12: ffff81003fb9d858
R13: 0000000000000000 R14: ffffffff80598460 R15: ffffffff80ab1fc0
FS: 0000000000000000(0000) GS:ffffffff806c4200(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: ffffffff82800000 CR3: 0000000000201000 CR4: 00000000000006e0
this crash happened because it did not sanitize the dwarf2 data it
got, and got an unaligned stack pointer - which happily walked past
the process stack (and eventually reached the end of kernel memory
and pagefaulted there) due to this naive iteration condition:
HANDLE_STACK (((long) stack & (THREAD_SIZE-1)) != 0);
note that i386 is alot more conservative when it comes to trusting
stack pointers:
static inline int valid_stack_ptr(struct thread_info *tinfo, void *p)
{
return p > (void *)tinfo &&
p < (void *)tinfo + THREAD_SIZE - 3;
}
but the x86_64 code did not take this bit of i386 code.
The fix is to align the stack pointer.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
on x86_64, the CONFIG_CC_STACKPROTECTOR build fails if used in a
distcc setup that has "CC" defined to "distcc gcc":
gcc: gcc: linker input file unused because linking not done
gcc: gcc: linker input file unused because linking not done
gcc: gcc: linker input file unused because linking not done
this is because the gcc-x86_64-has-stack-protector.sh script
has a 2-parameters assumption. Fix this by passing $(CC) as
a single parameter.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Please-Use-Me-More: make randconfig
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The HP_SIMSCSI driver can't be built as a module (unhealthy dependencies on
things that shouldn't really be exported).
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Use generic_handle_irq() to handle mixed-type irq handling.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
`typename' is going away and is usually uninitialised anwyay.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When called to do a transfer that has a start offset within the cache
line which is uneven between source and destination and a length which
terminates the source of the copy exactly on a cache line, one extra
line gets copied into a temporary buffer. This is normally not an issue
since the buffer is a kernel buffer and only the requested information
gets copied into the user buffer.
The problem arises when the source ends at the very last physical page
of memory. That last cache line does not exist and results in the SHUB
chip raising an MCA.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Komuro reports that ISA interrupts do not work after a disable_irq(),
causing some PCMCIA drivers to not work, with messages like
eth0: Asix AX88190: io 0x300, irq 3, hw_addr xx:xx:xx:xx:xx:xx
eth0: found link beat
eth0: autonegotiation complete: 100baseT-FD selected
eth0: interrupt(s) dropped!
eth0: interrupt(s) dropped!
eth0: interrupt(s) dropped!
...
Linus Torvalds <torvalds@osdl.org> said:
"Now, edge-triggered interrupts are a _lot_ harder to mask, because the
Intel APIC is an unbelievable piece of sh*t, and has the edge-detect logic
_before_ the mask logic, so if a edge happens _while_ the device is
masked, you'll never ever see the edge ever again (unmasking will not
cause a new edge, so you simply lost the interrupt).
So when you "mask" an edge-triggered IRQ, you can't really mask it at all,
because if you did that, you'd lose it forever if the IRQ comes in while
you masked it. Instead, we're supposed to leave it active, and set a flag,
and IF the IRQ comes in, we just remember it, and mask it at that point
instead, and then on unmasking, we have to replay it by sending a
self-IPI."
This trivial patch solves the problem.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@redhat.com>
Acked-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] x86-64: Fix race in exit_idle
[PATCH] x86-64: Fix vgetcpu when CONFIG_HOTPLUG_CPU is disabled
[PATCH] x86: Add acpi_user_timer_override option for Asus boards
[PATCH] x86-64: setup saved_max_pfn correctly (kdump)
[PATCH] x86-64: Handle reserve_bootmem_generic beyond end_pfn
[PATCH] x86-64: shorten the x86_64 boot setup GDT to what the comment says
[PATCH] x86-64: Fix PTRACE_[SG]ET_THREAD_AREA regression with ia32 emulation.
[PATCH] x86-64: Fix partial page check to ensure unusable memory is not being marked usable.
Revert "[PATCH] MMCONFIG and new Intel motherboards"
(David:)
If hugetlbfs_file_mmap() returns a failure to do_mmap_pgoff() - for example,
because the given file offset is not hugepage aligned - then do_mmap_pgoff
will go to the unmap_and_free_vma backout path.
But at this stage the vma hasn't been marked as hugepage, and the backout path
will call unmap_region() on it. That will eventually call down to the
non-hugepage version of unmap_page_range(). On ppc64, at least, that will
cause serious problems if there are any existing hugepage pagetable entries in
the vicinity - for example if there are any other hugepage mappings under the
same PUD. unmap_page_range() will trigger a bad_pud() on the hugepage pud
entries. I suspect this will also cause bad problems on ia64, though I don't
have a machine to test it on.
(Hugh:)
prepare_hugepage_range() should check file offset alignment when it checks
virtual address and length, to stop MAP_FIXED with a bad huge offset from
unmapping before it fails further down. PowerPC should apply the same
prepare_hugepage_range alignment checks as ia64 and all the others do.
Then none of the alignment checks in hugetlbfs_file_mmap are required (nor
is the check for too small a mapping); but even so, move up setting of
VM_HUGETLB and add a comment to warn of what David Gibson discovered - if
hugetlbfs_file_mmap fails before setting it, do_mmap_pgoff's unmap_region
when unwinding from error will go the non-huge way, which may cause bad
behaviour on architectures (powerpc and ia64) which segregate their huge
mappings into a separate region of the address space.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Adam Litke <agl@us.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix interrupt routing for via 586 bridges. pirq can be 5 which needs to be
mapped to INTD. But currently the access functions can handle only pirq
1-4. this is similar to the other via chipsets where pirq 4 and 5 are both
mapped to INTD. Fixes bugzilla #7490
Cc: Daniel Paschka <monkey20181@gmx.net>
Cc: Adrian Bunk <bunk@susta.de>
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When another interrupt happens in exit_idle the exit idle notifier
could be called an incorrect number of times.
Add a test_and_clear_bit_pda and use it handle the bit
atomically against interrupts to avoid this.
Pointed out by Stephane Eranian
Signed-off-by: Andi Kleen <ak@suse.de>
The vgetcpu per CPU initialization previously relied on CPU hotplug
events for all CPUs to initialize the per CPU state. That only
worked only on kernels with CONFIG_HOTPLUG_CPU enabled. On the
others some CPUs didn't get their state initialized properly
and vgetcpu wouldn't work.
Change the initialization sequence to instead run in a normal
initcall (which runs after the normal CPU bootup) and initialize
all running CPUs there. Later hotplug CPUs are still handled
with an hotplug notifier.
This actually simplifies the code somewhat.
Signed-off-by: Andi Kleen <ak@suse.de>
Timer overrides are normally disabled on Nvidia board because
they are commonly wrong, except on new ones with HPET support.
Unfortunately there are quite some Asus boards around that
don't have HPET, but need a timer override.
We don't know yet how to handle this transparently,
but at least add a command line option to force the timer override
and let them boot.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
x86_64: setup saved_max_pfn correctly
2.6.19-rc4 has broken CONFIG_CRASH_DUMP support on x86_64. It is impossible
to read out the kernel contents from /proc/vmcore because saved_max_pfn is set
to zero instead of the max_pfn value before the user map is setup.
This happens because saved_max_pfn is initialized at parse_early_param() time,
and at this time no active regions have been registered. save_max_pfn is setup
from e820_end_of_ram(), more exact find_max_pfn_with_active_regions() which
returns 0 because no regions exist.
This patch fixes this by registering before and removing after the call
to e820_end_of_ram().
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
This can happen on kexec kernels with some configurations, in particularly
on Unisys ES7000 systems.
Analysis by Amul Shah
Cc: Amul Shah <amul.shah@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Stephen Tweedie, Herbert Xu, and myself have been struggling with a very
nasty bug in Xen. But it also pointed out a small bug in the x86_64
kernel boot setup.
The GDT limit being setup by the initial bzImage code when entering into
protected mode is way too big. The comment by the code states that the
size of the GDT is 2048, but the actual size being set up is much bigger
(32768). This happens simply because of one extra '0'.
Instead of setting up a 0x800 size, 0x8000 is set up. On bare metal this
is fine because the CPU wont load any segments unless they are
explicitly used. But unfortunately, this breaks Xen on vmx FV, since it
(for now) blindly loads all the segments into the VMCS if they are less
than the gdt limit. Since the real mode segments are around 0x3000, we are
getting junk into the VMCS and that later causes an exception.
Stephen Tweedie has written up a patch to fix the Xen side and will be
submitting that to those folks. But that doesn't excuse the GDT limit
being a magnitude too big.
AK: changed to compute true gdt size in assembler, fixed comment
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andi Kleen <ak@suse.de>
ptrace(PTRACE_[SG]ET_THREAD_AREA) calls from ia32 code
should be passed onto the x86_64 implementation.
The default case in sys32_ptrace used to call to sys_ptrace(), but is
now EINVAL. This patch fixes a regression caused by that changed.
Signed-off-by: Mike McCormack <mike@codeweavers.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix partial page check in e820_register_active_regions to ensure
partial pages are
not being marked as active in the memory pool.
Signed-off-by: Aaron Durbin <adurbin@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
OP_MAX_COUNTER never referenced, and is a reminant of an earlier
oprofile implementation. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] cell: set ARCH_SPARSEMEM_DEFAULT in Kconfig
[POWERPC] Fix cell "new style" mapping and add debug
[POWERPC] pseries: Force 4k update_flash block and list sizes
[POWERPC] CPM_UART: Fix non-console initialisation
[POWERPC] CPM_UART: Fix non-console transmit
[POWERPC] Make sure initrd and dtb sections get into zImage correctly
Fix MSPEC driver to build for non SN2 enabled configs as the driver should
work in cached and uncached modes (no fetchop) on these systems. In
addition make MSPEC select IA64_UNCACHED_ALLOCATOR, which is required for
it and move it to arch/ia64/Kconfig to avoid warnings on non ia64
architectures running allmodconfig. Once the Kconfig code is fixed, we can
move it back.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Cc: Fernando Luis Vzquez Cao <fernando@oss.ntt.co.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new 'wrapper' code generates files that git should ignore;
add them to .gitignore.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a check for a null ppc_md.init_early to allow platforms that
don't require an init_early routine to just set this member to null.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The qe_brg structure manually defined each of the 16 BRG registers, which
made any code that used them cumbersome. This patch replaces the fields
with a single 16-element array.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix compile warnings with CONFIG_PM=n
arch/powerpc/platforms/powermac/feature.c:489: warning: 'save_gpio_levels' defined but not used
arch/powerpc/platforms/powermac/feature.c:490: warning: 'save_gpio_extint' defined but not used
arch/powerpc/platforms/powermac/feature.c:491: warning: 'save_gpio_normal' defined but not used
arch/powerpc/platforms/powermac/feature.c:492: warning: 'save_unin_clock_ctl' defined but not used
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bootwrapper Makefile does not clean up the 'zImage' file that
may be left laying around. This patch removes it when cleaning that
directory.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When the wrapper script is passed a dts file, it runs 'dtc' to create
a dtb file. This patch deletes that dtb file once its no longer needed.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
bad_page_fault() prints a message telling the user what type of bad
fault we took. The first line of this message is currently implemented
as two separate printks. This has the unfortunate effect that if
several cpus simultaneously take a bad fault, the first and second parts
of the printk get jumbled up, which looks dodge and is hard to read.
So do a single one-line printk for each fault type.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Cleaned up interrupt mapping a little by adding a helper
function which parses the irq out of the device-tree, and puts
it into a resource.
* Changed the arch/ppc platform files to specify PHY_POLL, instead of -1
* Changed the fixed phy to use PHY_IGNORE_INTERRUPT
* Added ethtool.h and mii.h to phy.h includes
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add Efika (http://www.bplan-gmbh.de/efika_spec_en.html) platform
support for arch/powerpc.
Signed-off-by: Nicolas DET <nd@bplan-gmbh.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds support for the MPC52xx Interrupt controller for
ARCH=powerpc.
It includes the main code in arch/powerpc/sysdev/ as well as a header
file in include/asm-powerpc.
Signed-off-by: Nicolas DET <nd@bplan-gmbh.de>
Acked-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make nvram_64.o dependent on 64bit, not on MULTIPLATFORM.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
dev_t boot_dev is declared in arch/powerpc/kernel/setup_32.c
and in arch/powerpc/kernel/setup_64.c but not used in these files.
It is only used in arch/powerpc/platforms/powermac/setup.c, so make
it static in this file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since iSeries is merged to MULTIPLATFORM, there is no way to build a 64bit
kernel without MULTIPLATFORM, so PPC_MULTIPLATFORM can be removed in
64bit-only files.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since iSeries is merged to MULTIPLATFORM, there is no way to build a 64bit
kernel without MULTIPLATFORM, so PPC_MULTIPLATFORM can be removed in
64bit-only files.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Most ARM defconfigs don't actually need to have PM_LEGACY enabled.
Disable it for ATEB9200, Collie, IXP4xx, OMAP H2, S3C2410 and
Versatile.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current cell processor support needs sparsemem, so set it as
the default memory model.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a typo in the "new style" code for mapping SPE resources,
which causes it to try to map the same resource 4 times.
It also adds some pr_debug's that are useful to track down issues with
the firmware when bringinh up new machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The enablement of 64k pages on pseries platforms exposed a bug in
the RTAS mechanism for updating firmware. RTAS assumes 4k for flash
block and list sizes, and use of any other sizes results in a failure,
even though PAPR does not specify any such requirement.
This patch changes the rtas_flash module to force the use of 4k memory
block and list sizes when preparing and sending a firmware image to
RTAS. The rtas_flash function now uses a slab cache of 4k blocks with
4k alignment, rather than get_zeroed_page(), to allocate the memory for
the flash blocks and lists. The 4k alignment requirement is specified
in PAPR.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds platform devices' registration for the devices which drivers
either have been added to the mainline or on the way to.
arch/arm/mach-pnx4008/core.c | 69 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 69 insertions(+)
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The "wrapper" script was using the wrong names for the initrd and
dtb (device-tree blob) sections. This fixes it, and also ensures
the symbols for the start and end of the dtb get defined correctly.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This refactoring actually optimizes the code a little by caching the value
that we think the device is programmed with instead of reading it back from
the hardware. Which simplifies the code a little and should speed things up a
bit.
This patch introduces the concept of a ht_irq_msg and modifies the
architecture read/write routines to update this code.
There is a minor consistency fix here as well as x86_64 forgot to initialize
the htirq as masked.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Acked-by: Bryan O'Sullivan <bos@pathscale.com>
Cc: <olson@pathscale.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When ACPI && NUMA, pxm_to_node is used and it exists in drivers/acpi/numa.c
Tony said:
The patch makes sense ... if you pick both of "ACPI" and "NUMA", then you
need (and should automatically be given) ACPI_NUMA too.
The only open question is whether there is a better way of getting there.
Perhaps with less configuration options in the first place? We are heading
towards a future where so many systems will be NUMA that there would seem to
be little benefit in keeping ACPI_NUMA separate from ACPI ... but perhaps
we aren't quite there yet.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujtisu.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are two bugs in the kretprobe-booster.
1) It doesn't make room for gs registers.
2) It doesn't change status of the current kprobe. This status will
effect the fault handling.
This patch fixes these bugs and, additionally, saves skipped registers for
compatibility with the original kretprobe.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Currently there is no specific alignment restriction in linker script
and in some cases it can be placed non 4K aligned addresses. This fails
kexec which checks that segment to be loaded is page aligned.
o I guess, it does not harm data segment to be 4K aligned.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the microcode driver is built in (rather than module) there are some,
ehm, interesting effects happening due to the new "call out to userspace"
behavior that is introduced.. and which runs too early. The result is a
boot hang; which is really nasty.
The patch below is a minimally safe patch to fix this regression for 2.6.19
by just not requesting actual microcode updates during early boot. (That
is a good idea in general anyway)
The "real" fix is a lot more complex given the entire cpu hotplug scenario
(during cpu hotplug you normally need to load the microcode as well); but
the interactions for that are just really messy at this point; this fix at
least makes it work and avoids a full detangle of hotplug.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/x86_64/kernel/cpufreq/../../../i386/kernel/cpu/cpufreq/speedstep-lib.c:131: error: 'MSR_FSB_FREQ' undeclared (first use in this function)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
On some systems such as the IBM x3650 there are bits set in the
upper half of the control values provided by the _PSS object.
These bits are only relevant for cpufreq drivers that use IO ports
which are not currently supported by the speedstep-centrino driver.
The current MSR oriented code assumes that upper bits are not set
and thus fails to work correctly when they are. e.g. the control
and status value equality check fails even though the ACPI spec
allows the inequality.
Signed-off-by: Gary Hade <garyh@us.ibm.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This is the x86-64 version of f9dadfa71b
that did the same thing on i386.
Since the "mask" bit is in the low word, when we write a new entry, we
need to write the high word first, before we potentially unmask it.
The exception is when we actually want to mask the interrupt, in which
case we want to write the low word first to make sure that the high word
doesn't change while the interrupt routing is still active.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is just commit 130fe05dbc ported to
x86-64, for all the same reasons. It cleans up the IO-APIC accesses in
order to then fix the ordering issues.
We move the accessor functions (that were only used by io_apic.c) out of
a header file, and use proper memory-mapped accesses rather than making
up our own "volatile" pointers.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit de09bddb9d. It tried
to reserve the MMCONFIG mmio memory ranges, but since the MMCONFIG
information is broken and often bogus (which is why we don't dare use it
most of the time _anyway_), it does more harm than good.
Cc: Jeff Chua <jeff.chua.linux@gmail.com>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains a fix for a bug introduced more than a year ago
(not setting *eof) and updates whitespace a bit.
Signed-off-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>
show_mem() was not correctly handling holes in the memory
map. It was treating the freed sections of the map as
though they contained valid struct page entries. This
could cause incorrect debugging output or even a kernel
panic.
This patch keeps the struct meminfo around after system
initialization so that show_mem() can use it when
scanning memory. show_mem() now walks over each bank
of each online node, rather than assuming that each node
contains a single contiguous bank.
Signed-off-by: Ray Lehtiniemi <rayl@mail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The timer LED is unusable at HZ=large, since it's got
a hard-wired value of 100 ticks per cycle; when HZ=1024
(for example) it's essentially always-on. This patch
just makes that be HZ ticks per cycle.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Several more Intel CPUs are now capable using the p4-clockmod cpufreq
driver. As it is of limited use most of the time, print a big bold warning
if a better cpufreq driver might be available.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
o Fix warnings
o 768MB worth of I/O ports were insane
o 64-bit kernels don't need special handling because ioremap does the magic
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/momentum/ocelot_c/setup.o
arch/mips/momentum/ocelot_c/setup.c: In function 'momenco_time_init':
arch/mips/momentum/ocelot_c/setup.c:223: warning: format '%d' expects type 'int', but argument 2 has type 'long unsigned int'
Change data type to match format string; a 32-bit type better suits our
needs.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
AVR32: Add missing return instruction in __raw_writesb
AVR32: Wire up sys_epoll_pwait
AVR32: Fix thinko in generic_find_next_zero_le_bit()
AVR32: Get rid of board_early_init
__raw_writesb ends with a conditional branch, which is obviously
wrong. It should return after the last loop terminates.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
setup_lowcore() calls ctl_set_bit() which returns withs interrupts
enabled. The setup arch code is not supposed to enable interrupts that
early. Therefore use the __ctl_set_bit() variant.
This fixes the not working lock dependency validator on non 64 bit
systems.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit 7676bef9c1 breaks DCSS support on
s390. DCSS needs initialized struct pages to work. With the usage of
add_active_range() only the struct pages for physically present pages
are initialized.
This could be fixed if the DCSS driver would initiliaze the struct pages
itself, but this doesn't work too. This is because the mem_map array
does not include holes after the last present memory area and therefore
there is nothing that could be initialized.
To fix this and to avoid some dirty hacks revert this patch for now.
Will be added later when we move to a virtual mem_map.
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The existing implementation of this function seems to be looking for
a one although it should be looking for a zero. This causes trouble
for the ext2 filesystem, which tends to report -ENOSPC without this
patch.
Fix this by complementing each word before scanning.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
board_early_init() is left over from some early prototyping work
where we had to initialize the SDRAM controller ourselves. This
depends on the kernel being loaded into static RAM, which just
isn't possible on any commercially available products today.
In order to run without a boot loader, we need to create a zImage
stub or have the debugger initialize the SDRAM for us (for really
low-level debugging)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
When I added the entries for the robust futex syscall entries, I
forgot to bump NR_SYSCALLS. The current situation is error-prone
because NR_SYSCALLS lives in entry.S where the system call limit
checks are enforced. Move the definition to asm/unistd.h in order to
make this mistake much more difficult to make.
And wire up sys_migrate_pages since the powerpc folks implemented the
compat wrapper for us.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to get the __NR_* constants, we need sys/syscall.h.
linux/unistd.h works as well since it includes syscall.h, however syscall.h
is more parsimonious. We were inconsistent in this, and this patch adds
syscall.h includes where necessary and removes linux/unistd.h includes
where they are not needed.
asm/unistd.h also includes the __NR_* constants, but these are not the
glibc-sanctioned ones, so this also removes one such inclusion.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a UML hang in which everything would just stop until some I/O happened
- a ping, someone whacking the keyboard - at which point everything would
start up again as though nothing had happened.
The cause was gcc reordering some code which absolutely needed to be
executed in the order in the source. When unblock_signals switches signals
from off to on, it needs to see if any interrupts had happened in the
critical section. The interrupt handlers check signals_enabled - if it is
zero, then the handler adds a bit to the "pending" bitmask and returns.
unblock_signals checks this mask to see if any signals need to be
delivered.
The crucial part is this:
signals_enabled = 1;
save_pending = pending;
if(save_pending == 0)
return;
pending = 0;
In order to avoid an interrupt arriving between reading pending and setting
it to zero, in which case, the record of the interrupt would be erased,
signals are enabled.
What happened was that gcc reordered this so that 'save_pending = pending'
came before 'signals_enabled = 1', creating a one-instruction window within
which an interrupt could arrive, set its bit in pending, and have it be
immediately erased.
When the I/O workload is purely disk-based, the loss of a block device
interrupt stops the entire I/O system because the next block request will
wait for the current one to finish. Thus the system hangs until something
else causes some I/O to arrive, such as a network packet or console input.
The fix to this particular problem is a memory barrier between enabling
signals and reading the pending signal mask. An xchg would also probably
work.
Looking over this code for similar problems led me to do a few more
things:
- make signals_enabled and pending volatile so that they don't get cached
in registers
- add an mb() to the return paths of block_signals and unblock_signals so
that the modification of signals_enabled doesn't get shuffled into the
caller in the event that these are inlined in the future.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the new drivers, such as SPI, LED and RTC core,
to the s3c2410_defconfig.
Signed-off-by: Ben Dooks <ben-linux@fluff.irg>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the bast_defconfig, as it has not been updated
since 2.6.13. The s3c2410_defconfig should be a good
replacement.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the smdk2410_defconifg as it is out of data
and has not been touched since 2.6.11.
Use the s3c2410_defconfig instead.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a rework of the ixp4xx irq_chip implementation. The use of
two irq_chip structures and potentially switching between them is a
violation of the intended use of the IRQ framework. The current
implementation does not work with current in-kernel spinlock debugging
or lockdep due to lock recursion problems caused by calling
set_irq_chip/handler from within the chip's set_irq_type().
This patch goes back to using one irq_chip structure and handling the
differences between edge/level, normal/GPIO interrupts inside the
ack/mask/unmask routines themselves.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM patch 3756/1 added HWCAP_IWMMXT. This patch adds support
for broadcasting that info via /proc/cpuinfo and sets it for
the CPU features of the PXA270.
I've booted 19rc3 on a pxa270 and confirmed that the /proc/cpuinfo
shows "iwmmxt" in the Features.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
s3c2410_gpio_getirq() holds for the S3C2412 build,
so ensure that it gets built for all the current
S3C24XX architectures
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dma_sync_single is no more (and to be removed in 2.7) so this export should be dma_sync_single_for_cpu.
Also export dma_sync_single_for_device.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On 64-bit kernel, modules are loaded into XKSEG for now. While XKSEG
address is not a sign-extended 32-bit address, we can not use -msym32
option.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/momentum/ocelot_g/gt-irq.o
arch/mips/momentum/ocelot_g/gt-irq.c:30:5: warning: "CURRENTLY_UNUSED" is not defined
arch/mips/momentum/ocelot_g/gt-irq.c:199:5: warning: "CURRENTLY_UNUSED" is not defined
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When lmo commit 4ef893e0515e8bf336dfbd200884f244869fbb43 was merged to
kernel.org as e73ea273ef patch happily
applied the IP27 segment to IP22. f63f36c18b11e166d0f362ac04dbcd7e6ea23f9e
did fix the effects partially - and with a wrong log message. Now fixed
for real (tm).
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch happily applied an Ocelot G patch to Ocelot C when merging
linux-mips.org changeset 91ee9a801e65d2981dfe327d2519c7fc6ab02e6b into
kernel.org as 6ceb6d3ab2.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit 31473747bd.
Another amazing example of patch(1) messing up - lmo changeset
66e8560d11d02bcadc261498471831a6375ad046 was merged twice to kernel.org
and ended up doing this rubbish job.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It turns out that the linker warnings on 64-bit powerpc about "section
blah exceeds stub group size" were being triggered by conditional
branches in head_64.S branching to global symbols, whether in
head_64.S or in other files. This eliminates the warnings by making
some global symbols in head_64.S no longer global, and by rearranging
some branches.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[ Yee-haa. Maybe I'll notice newly introduced real warnings now - Linus ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since the "mask" bit is in the low word, when we write a new entry, we
need to write the high word first, before we potentially unmask it.
The exception is when we actually want to mask the interrupt, in which
case we want to write the low word first to make sure that the high word
doesn't change while the interrupt routing is still active.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is preparation for fixing the ordering of the accesses that
got broken by the commit cf4c6a2f27 when
factoring out the "common" io apic routing entry accesses.
Move the accessor function (that were only used by io_apic.c) out
of a header file, and use proper memory-mapped accesses rather than
making up our own "volatile" pointers.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The alignment exception used to only check the exception table for
-EFAULT, not for other errors. That opens an oops window if we can
coerce the kernel into getting an alignment exception for other reasons
in what would normally be a user-protected accessor, which can be done
via some of the futex ops. This fixes it by always checking the
exception tables.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On powerpc, probing on emulate_step function will crash 2.6.18.1 when
it is triggered.
When kprobe is triggered, emulate_step() is on its kernel path and
will cause recursive kprobe fault. And branch_taken() is called
in emulate_step(). This disallows kprobes on both of them.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Checking source for other get_paca()->field preemption dangers found that
open_high_hpage_areas does a structure copy into its paca while preemption
is enabled: unsafe however gcc accomplishes it. Just remove that copy:
it's done safely afterwards by on_each_cpu, as in open_low_hpage_areas.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Changed qe_issue_cmd() to write cmd_input to the CECDR unmodified. It
was treating cmd_input as a virtual address and tried to convert it to
a physical address.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 10Gigabit ethernet device drivers appear to be able to chew
up all 256MB of TCE mappings on pSeries systems, as evidenced by
numerous error messages:
iommu_alloc failed, tbl c0000000010d5c48 vaddr c0000000d875eff0 npages 1
Some experimentation indicates that this is essentially because
one 1500 byte ethernet MTU gets mapped as a 64K DMA region when
the large 64K pages are enabled. Thus, it doesn't take much to
exhaust all of the available DMA mappings for a high-speed card.
This patch changes the iommu allocator to work with its own
unique, distinct page size. Although the patch is long, its
actually quite simple: it just #defines a distinct IOMMU_PAGE_SIZE
and then uses this in all the places that matter.
As a side effect, it also dramatically improves network performance
on platforms with H-calls on iommu translation inserts/removes (since
we no longer call it 16 times for a 1500 bytes packet when the iommu HW
is still 4k).
In the future, we might want to make the IOMMU_PAGE_SIZE a variable
in the iommu_table instance, thus allowing support for different HW
page sizes in the iommu itself.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixed a compile error in building the 85xx support with oprofile, and in
the process cleaned up some issues with the fsl_booke performance monitor
code.
* Reorganized FSL Book-E performance monitoring code so that the 7450
wouldn't be built if the e500 was, and cleaned it up so it was more
self-contained.
* Added a cpu_setup function for FSL Book-E. The original
cpu_setup function prototype had no arguments, assuming that
the reg_setup function would copy the required information into
variables which represented the registers. This was silly for
e500, since it has 1 register per counter (rather than 3 for
all counters), so the code has been restructured to have
cpu_setup take the current counter config array as an argument,
with op_powerpc_setup() invoking op_powerpc_cpu_setup() through
on_each_cpu(), and op_powerpc_cpu_setup() invoking the
model-specific cpu_setup function with an argument. The
argument is ignored on all other platforms at present.
* Fixed a confusing line where a trinary operator only had two
arguments
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a few issues in offb:
- A test was inverted causing the palette hack to never work
(no device node was passed down to the init function)
- Some cards seem to have their assigned-addresses property in a random
order, thus we need to try using of_get_pci_address() first, which will
fail if it's not a PCI device, and fallback to of_get_address() in that
case. of_get_pci_address() properly parsees assigned-addresses to test
the BAR number and thus will get it right whatever the order is.
- Some cards (like GXT4500) provide a linebytes of 0xffffffff in the
device-tree which does no good. This patch handles that by using the
screen width when that happens. (Also fixes btext.c while at it).
- Add detection of the GXT4500 in addition to the GXT2000 for the
palette hacks (we use the same hack, palette is linear in register space
at offset 0x6000).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'release' of master.kernel.org:/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Correct definition of handle_IPI
[IA64] move SAL_CACHE_FLUSH check later in boot
[IA64] MCA recovery: Montecito support
[IA64] cpu-hotplug: Fixing confliction between CPU hot-add and IPI
[IA64] don't double >> PAGE_SHIFT pointer for /dev/kmem access
The declaration of handle_IPI in arch/ia64/kernel/smp.c was changed but
not the definition of this function. Remove struct pt_regs from
handle_IPI().
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The check to see if the firmware drops interrupts during a
SAL_CACHE_FLUSH is done to early in the boot. SAL_CACHE_FLUSH expects
to be able to make PAL calls in virtual mode, on some cell based
machines a fault occurs causing a MCA. This patch moves the check
after mmu_context_init so the TLB and VHPT are properly setup.
Signed-off-by Troy Heber <troy.heber@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The information in MCA records is filled in slightly differently on
Montecito than on Madison/McKinley. Usually, the cache check and bus
check target identifiers have the same address. On Montecito the
cache check and bus check target identifiers can be different if
a corrected error (ie SBE or unconsumed poison data) was encountered and
then an uncorrected error (ie DBE) was consumed. In that case, the
cache check target identifier is the physical address of the DBE (that
caused the MCA to surface) while the bus check target identifier is the
physical address of the SBE. This patch correctly finds the target
identifier that triggered the MCA.
If there are multiple valid cache target identifiers in the same
error record then use the one with the lowest cache level.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Since we already moved to GENERIC_TIME, we should implement alternatives
of old do_gettimeoffset routines to get sub-jiffies resolution from
gettimeofday(). This patch includes:
* MIPS clocksource support (based on works by Manish Lachwani).
* remove unused gettimeoffset routines and related codes.
* remove unised 64bit do_div64_32().
* simplify mips_hpt_init. (no argument needed, __init tag)
* simplify c0_hpt_timer_init. (no need to write to c0_count)
* remove some hpt_init routines.
* mips_hpt_mask variable to specify bitmask of hpt value.
* convert jmr3927_do_gettimeoffset to jmr3927_hpt_read.
* convert ip27_do_gettimeoffset to ip27_hpt_read.
* convert bcm1480_do_gettimeoffset to bcm1480_hpt_read.
* simplify sb1250 hpt functions. (no need to subtract and shift)
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/kernel/traps.c:1115: warning: int format, long unsigned int arg (arg 2)
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
