The slot-gpio API provides a generic card-detection handler. To support a
wider range of hosts it has to call the host's card-event callback, if
implemented. Also increase the debounce interval to 200ms to match the
SDHCI driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
'sc' is used only when CONFIG_PM_RUNTIME is defined. Hence define it
conditionally.
Silences the following warning:
drivers/mmc/host/sdhci-s3c.c: In function ‘sdhci_s3c_notify_change’:
drivers/mmc/host/sdhci-s3c.c:378:20: warning: unused variable ‘sc’ [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The Ricoh SDHCI controllers support Highspeed clocks as evident from
the ricoh_mmc_probe_slot() settings. Hence, SDHCI_CAN_DO_HISPD needs
to be set to enable SDIO client drivers to set/enable high speed clock
settings
Signed-off-by: Madhvapathi Sriram <Madhvapathi.Sriram@csr.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This commit taken from Rabeeh's Cubox kernel and re-worked for DT;
Sebastian Hasselbrath is believed to be the original author.
Some Cuboxes require a GPIO for card detection; this implements the
optional GPIO support for card detection. This GPIO is logic 0 for
card inserted.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
We need to use the two-stage initialization for sdhci-pltfm if we're
going to do anything extra at initialization time.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use devm_clk_get() rather than clk_get() to make cleanup paths more simple.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
A-003500: False ADMA Error might be reported when ADMA is used for
multiple block read command with Stop at Block Gap. If PROCTL[SABGREQ]
is set when the particular block's data is received by the System side
logic before entire block (with CRC) data is received by the SD side
logic, and also if ADMA descriptor line is fetched at the same time,
then DMA engine might report false ADMA error. eSDHC might not be able
to Continue (PROCTL[CREQ]=1) after Stop at Block Gap.
This issue will impact the eSDHC IP VVN2.3.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
ctype is using 1-bit buswidth mode by default.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
To ensure the stable clock need to enable before set the
DW_MMC_CARD_NEED_INIT flag. If set DW_MMC_CARD_NEED_INIT flag,
wait for 80-clock before first command after power-up.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If "caps2" host capabilities does not indicate support for MMC
HS200, don't allow clock speeds >52MHz. Currently, for MMC, the
clock speed is set to the lesser of the max speed the eMMC module
supports (card->ext_csd.hs_max_dtr) or the max base clock of the
host controller (host->f_max based on BASE_CLK_FREQ in the host
CAPS register). This means that a host controller that doesn't
support HS200 mode but has a base clock of 100MHz and an eMMC module
that supports HS200 speeds will end up using a 100MHz clock.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use managed device resource functions for easy handling.
This makes driver simpler in the routine of error and exit.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMCIF only uses one clock, all ARM and SuperH platforms register MMCIF
clock lookup entries with no connection ID, hence it can be dropped in
the driver too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHI only uses one clock, all ARM and SuperH platform register SDHI clock
lookup entries with no connection ID, hence it can be dropped in the
driver too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
During its probing the SDHI driver prints out the clock frequency, but
does it wrongly, always reporting 0Hz. Use the MMC host frequency value
to fix this issue.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use devm_kzalloc, devm_gpio_request_one and devm_request_irq to make
cleanup path simpler.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The OLPC XO-1.75 laptop includes a SDHCI controller which is 1.8v
capable, and it truthfully reports so in its capabilities. This
alternate voltage is used for driving new "UHS-I" SD cards at their
full speed.
However, what the controller doesn't know is that the motherboard
physically doesn't have a 1.8v supply available, so attempting to
switch to the 1.8v level will result in a situation that cannot be
recovered from without physically replugging the SD card.
Add a device tree flag that can be used on systems like these,
and hook it up to the equivalent SDHCI quirk.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The OLPC XO-1.75 laptop includes a SDHCI controller which is 1.8v
capable, and it truthfully reports so in its capabilities. This
alternate voltage is used for driving new "UHS-I" SD cards at their
full speed.
However, what the controller doesn't know is that the motherboard
physically doesn't have a 1.8v supply available.
Add a quirk so that systems such as this one can override disable
1.8v support, adding support for UHS-I cards (by running them at
3.3v).
This avoids a problem where the system would first try to run the
card at 1.8v, fail, and then not be able to fully reset the card
to retry at the normal 3.3v voltage.
This is more appropriate than using the MISSING_CAPS quirk, which
is intended for cases where the SDHCI controller is actually lying
about its capabilities, and would force us to somehow override both
caps words from another source.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend methods provided by SDIO drivers are not supposed to be called by
the PM core. Instead, when the SDIO core gets to suspend a device's
ancestor, it calls the device driver's suspend routine. However, the PM
core executes suspend callback routines directly for device drivers whose
bus types don't provide suspend callbacks. In consequece, because the
SDIO bus type doesn't provide a suspend callback, the SDIO drivers'
suspend routines will be executed by the PM core (which shouldn't
happen).
To prevent this from happening, add empty system suspend/resume callbacks
for the SDIO bus type.
An analogous change had been made already by commit (e841a7c mmc: sdio:
Use empty system suspend/resume callbacks at the bus level), but then it
was reverted inadvertently by commit (d8e2ac3 mmc: sdio: Fix PM_SLEEP
related build warnings) that attempted to fix build warnings introduced
by commit e841a7c.
Reported-by: NeilBrown <neilb@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add missing usb_put_dev on failure path in vub300_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Marina Makienko <makienko@ispras.ru>
Signed-off-by: Chris Ball <cjb@laptop.org>
clk_{un}prepare is mandatory for platforms using common clock
framework. Because for SPEAr we don't do anything in clk_{un}prepare()
calls, just call them once in probe/remove.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SPEAr sdhci driver expects the clock to be set to 50 MHz for proper
functioning. This patch sets clk to 50 MHz in probe.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for pin configuration using pinctrl subsystem
to the sdhci-s3c driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The set of GPIO pins used by sdhci-s3c driver varies between
configurations, such as card detect method, pinctrl availability, etc.
This overly complicates the code requesting and freeing GPIO pins, which
must check which pins are used, when freeing them.
This patch modifies the sdhci-s3c driver to use devm_gpio_request to
free requested pins automatically after unbinding the driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The IP versions older than 2.3 didn't support commands with busy
response which expect the TC bit set. But after the VVN2.3, eSDHC
IP has supported it.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The third argument for of_get_property() is a pointer, hence pass
NULL instead of 0.
Fixes the following sparse warning:
sdhci-s3c.c:452:48: warning: Using plain integer as NULL pointer
sdhci-s3c.c:457:52: warning: Using plain integer as NULL pointer
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Define the most frequently used bitmasks of the Interrupt Enable /
Interrupt Status register with consistent naming ( with _EN suffix).
Use meaningful concatenation of bitfields for INT_EN_MASK, which shows
which interrupts are enabled by default. No functional changes.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fatal errors for the driver are not reported when just error debug
is enabled. Convert selected dev_dbg to dev_err for accurate error
reporting.
Reported-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
prepare() is supposed to prevent new children from being registered.
On the MMC subsystem, children (new cards) registration starts with
the card detect IRQ.
Move card detect IRQ disabling to prepare() so that no new cards
will be registered while we're trying to suspend.
Likewise, move card detect IRQ enabling to complete() so we only
try to register new children after our MMC IP is back up.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
HSMMC IP on AM33xx need a special setting to handle High-speed cards.
Other platforms like TI81xx, OMAP4 may need this as-well. This depends
on the HSMMC IP timing closure done for the high speed cards.
From AM335x TRM (SPRUH73F - 18.3.12 Output Signals Generation):
The MMC/SD/SDIO output signals can be driven on either falling edge or
rising edge depending on the SD_HCTL[2] HSPE bit. This feature allows
to reach better timing performance, and thus to increase data transfer
frequency.
There are few pre-requisites for enabling the HSPE bit
- Controller should support High-Speed-Enable Bit and
- Controller should not be using DDR Mode and
- Controller should advertise that it supports High Speed in
capabilities register and
- MMC/SD clock coming out of controller > 25MHz
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Update error code to cmd->error for commands with response_busy and no data.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Avoid soft reset of command internal state machine on data errors.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
ae4bf788ee ("mmc: omap_hsmmc: consolidate error report handling of HSMMC
IRQ") sets both end_cmd and end_trans to 1.
Setting end_cmd to 1 for Data Timeout/CRC leads to NULL pointer dereference of
host->cmd as the command complete has previously been handled.
Set end_cmd only in case of command Timeout/CRC.
Moreover host->cmd->error should not be updated on data error case, only
host->data->error needs to be updated.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add dt-based retrieval of host sdio pm capabilities. Based on
the dt based discovery do a bus init in the resume function.
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add support for optional pm capabilities such as MMC_PM_KEEP_POWER
and MMC_PM_WAKE_SDIO_IRQ.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For regulator vmmc/vmmcq, use voltage range as below
3.3v/3.0v: (2.7v, 3.6v)
1.8v: (1.7v, 1.95v)
Original code uses the precise value which may fail in regulator
driver if it does NOT support the precise voltage.
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for the SD/MMC host controller found
on Wondermedia 8xxx series SoCs, currently supported under
arm/arch-vt8500.
A binding document is also included, based on mmc.txt with
additional properties.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
RPMB partition is accessing though /dev/block/mmcXrpmb device
User callers can read and write entire data frame(s) as defined
by JEDEC Standard JESD84-A441, using standard IOCTL interface.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Provide support for automatically sending Set Block Count
(CMD23) messages. Used at least for RPMB support.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Do not scan rpmb partitions for "soft" partitions, since the rpmb
partition contains protected data. Silences the following message
during boot:
mmcblkXRPMB: unknown partition table
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Following JEDEC standard, if the mmc supports RPMB partition,
a new interface is created and exposed via /dev/block.
Users will be able to access RPMB partition using standard
mmc IOCTL commands.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable the quirk SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN since
SD_CAPABILITIES_1[15:8](BASE_FREQ) can't get correct base clock value.
It returns a fixed pre-set value like 200 on some sdhci-pxav3 based
platforms like MMP3 while return 0 on the other sdhci-pxav3 based
platforms. So we enable the quirk and get the base clock via function
get_max_clock. Also add get_max_clock.
Reported-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Philip Rakity <prakity@Marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are discrepancies with regards to how MMC capabilities
are carried throughout the subsystem. Let's standardise them
to eliminate any confusion.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
All MXS users have been converted to device tree and the board files have
been removed.
No need to keep platform data in the driver.
Also move bus_width declaration in the beggining of mxs_mmc_probe() to
avoid: 'warning: ISO C90 forbids mixed declarations and code'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Before this patch, we always used only single sg entry for SDIO transfer.
This patch switches to using multiple sg entries. In the case of dwmci,
it supports only up to 4KB size per single sg entry. So if we want to
transfer more than 4KB, we should send more than 1 command.
When we tested before applying this patch, it took around 335 us for
5K(5120) bytes transfer with dwmci controller. After applying this patch,
it takes 242 us for 5K bytes. So this patch makes around 38% performance
improvement for 5K bytes transfer. If the transfer size is bigger, then
the performance improvement ratio will be increased.
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are infinite loops in the mmc code that can be caused by bad
hardware. The code will loop forever if the device never comes back
from program mode, R1_STATE_PRG, and it is not ready for data,
R1_READY_FOR_DATA.
A long timeout is added to prevent the code from looping forever.
The timeout will occur if the device never comes back from program
state or the device never becomes ready for data.
It's not clear whether the timeout will do more than log a pr_err()
and then start a fresh hang all over again. We may need to extend
this patch later to perform some kind of reset of the device (is
that possible?) or rejection of new I/O to the device.
Signed-off-by: Trey Ramsay <tramsay@linux.vnet.ibm.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The patch "dw_mmc: fix multiple drv_data NULL dereferences" has
unfortunately clashed with my "mmc: dw_mmc: constify dw_mci_idmac_ops
in exynos back-end" patch, causing new warnings to appear.
This should hopefully fix the issue for good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The at91-mci driver is not needed anymore since the atmel-mci driver now
supports all Atmel devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC debounce clock is applicable only for omap2430, warning message gets
printed when enable fails for debounce clock. Remove the get debounce clock
failure message as it is noisy for other platforms.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Maximum bus frequency can be limited by external circuitry like level
shifters etc. Allow passing this value from DT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This allows DT-driven board to set up the pin mux only when the driver
is in use.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When a SD card is initialized some data transfers of 64 and 8 bytes
are issued. It seems the DMA has some problems dealing with these kind
of "short" transfers, leading sometimes to the SD card not being detected.
In order to solve this problem, do not use DMA for transfer sizes lower
than the sector size.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since v3.2 we have nice macro to define the platform driver's init and exit
calls. This patch simplifies the dw_mmc platform driver by using that macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Girish K S <girish.shivanajappa@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In case both 'req' and 'mq->mqrq_prev->req' are null, there is no request
to be processed. That means there is no need to switch buffer.
Switching buffer is required only after finishing 'issue_fn'.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Tested-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The vmmc regulator enable in sdhci_add_host is NOT necessary since
it can be enabled during mmc_power_up by function mmc_regulator_set_ocr.
And this extra enable will make regulator_enable/regulator_disable
unbalanced. Consequently, vmmc can't be disabled during mmc_power_off.
Also, if the vqmmc regulator exists, it should be enabled regardless it
support 1.8v or not.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some systems, e.g., kzm9g, MMCIF interfaces can produce spurious
interrupts without any active request. To prevent the Oops, that results
in such cases, don't dereference the mmc request pointer until we make
sure, that we are indeed processing such a request.
Reported-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Cc: stable@vger.kernel.org
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 8464dd52d3, which was a misapplied debugging
version of the patch, not the final patch itself.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: stable@vger.kernel.org
2abeb5c5de ("Add clk_(enable/disable) in runtime suspend/resume")
added the capability to stop the clocks when the device is runtime
suspended, but forgot to handle the case of the card-detect using
an external gpio.
Therefore in the case that runtime-pm is enabled, start the io-clock
when a card is inserted and stop it again once it is removed.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinitconst is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-mmc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a driver for SDHCI controllers enumerated via ACPI and identified
by the ACPI Compatibility ID PNP0D40 (or other SDHCI-specific ACPI
hardware IDs in the future).
[rjw: Added the changelog.]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Chris Ball <cjb@laptop.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This fixes the following build error on some architectures (parisc at least):
drivers/mmc/host/rtsx_pci_sdmmc.c: In function 'sd_normal_rw':
drivers/mmc/host/rtsx_pci_sdmmc.c:448:2: error: implicit
declaration of function 'kzalloc'
[-Werror=implicit-function-declaration]
drivers/mmc/host/rtsx_pci_sdmmc.c:448:6: warning: assignment
makes pointer from integer without a cast [enabled by default]
drivers/mmc/host/rtsx_pci_sdmmc.c:472:2: error: implicit
declaration of function 'kfree'
[-Werror=implicit-function-declaration]
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For Realtek card reader, internal regsiter SD_CFG2 should be configured
before transferring data.
The default value of SD_CFG2 is proper for writing data. But for reading
sequence, the timing is not good enough. So in some extreme circumstance,
card reader may sample the response data from the card as good even if
the data is wrong. And this will cause the bad consequence.
In the prior version, the value of this register has been calculated,
but forgotten to write back to the internal register.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Realtek PCI-E SD/MMC card host driver is used to access SD/MMC card,
with the help of Realtek PCI-E card reader MFD driver.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
Here it is enough to switch to refcounting in tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty from struct sdio_uart_port is unused. Proper refcounted tty in
tty_port->tty is used instead. So remove the member from that
structure.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c5hx
-----END PGP SIGNATURE-----
Merge tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91 into next/headers
From Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
arm: at91: mach header cleanup
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
* tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91:
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Realtek PCI-E SD/MMC card host driver is used to access SD/MMC card,
with the help of Realtek PCI-E card reader MFD driver.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If host clock is disabled, host cannot detect a card in case of using
CD internal for detection.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The of_device_id match data is now marked as const and
must not be modified. This changes the dw_mmc to mark
all pointers passing the dw_mci_drv_data or dw_mci_dma_ops
structures as const, and also marks the static definitions
as const.
drivers/mmc/host/dw_mmc-exynos.c: In function 'dw_mci_exynos_probe':
drivers/mmc/host/dw_mmc-exynos.c:234:11: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The MODULE_DEVICE_TABLE entry for dw_mci_exynos_match
was incorrectly copied from the platform back-end, which
causes this error when building the driver as a loadable
module:
drivers/mmc/host/dw_mmc-exynos.c: At top level:
drivers/mmc/host/dw_mmc-exynos.c:226:34: error: '__mod_of_device_table' aliased to undefined symbol 'dw_mci_pltfm_match'
This patch fixes the problem by just using the correct
string.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit 473b095a72 ("mmc: sdhci: fix incorrect command used in tuning")
introduced a NULL dereference at resume-time if an SD 3.0 host controller
raises the SDHCI_NEEDS_TUNING flag while no card is inserted. Seen on an
OLPC XO-4 with sdhci-pxav3, but presumably affects other controllers too.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: stable <stable@vger.kernel.org> [3.3+]
There are two problems here:
The check for vmmc was printing an unnecessary pr_info() when
host->vmmc is NULL.
The intent of the check for vqmmc was to only remove UHS if we have a
regulator that doesn't support the required voltage, but since IS_ERR()
doesn't catch NULL, we were actually removing UHS modes if vqmmc isn't
present at all -- since it isn't present for most users, this breaks
UHS for them. This patch fixes that UHS regression in 3.7-rc1.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Bin Wang <binw@marvell.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
1. Never ever publish a device in the system before it has been setup
to a usable state.
2. Unregister the device _BEFORE_ taking away any resources it may be
using.
3. Don't check clks against NULL.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
A recent commit "mmc: sh_mmcif: fix clock management" has introduced a
use after free bug in sh_mmcif.c: in sh_mmcif_remove() the call to
mmc_free_host() frees private driver data, therefore using it afterwards
is a bug. Revert that hunk.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: stable@vger.kernel.org [3.6]
Signed-off-by: Chris Ball <cjb@laptop.org>
The SDHCI standard defines a 256 byte register set but a device
that specifies a larger iomem region is not an error. Alter the
message condition accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The correct name for the driver is "mxc-mmc".
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
dev->platform_data is NULL in case of device tree boot,
instead use the saved version in struct omap_hsmmc_host.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
struct omap_hsmmc_host *host should not be accessed after mmc_free_host().
Reorder mmc_free_host() after iounmap(host->base).
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
800d78bfcc ("mmc: dw_mmc: add support for implementation specific
callbacks") -- merged in v3.7-rc1 -- introduced multiple NULL pointer
dereferences when the default dw_mci_pltfm_probe() is used, as it sets
host->drv_data to NULL, and that's only checked against NULL in 1 out of
the 7 cases where it is dereferenced.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As mmc_start_host is getting called before enabling the dw_mmc controller
interrupt, there is a problem of missing the SDMMC_INT_CMD_DONE for the
very first command sent by the sdio_reset.
This problem occurs only when we disable MMC debugging i.e, MMC_DEBUG=n.
This patch enables the dw_mmc controller interrupt before mmc_start_host.
Signed-off-by: Yuvaraj CD <yuvaraj.cd@samsung.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
CMD23 causes lots of errors in kernel on some freescale SoCs
(P1020, P1021, P1022, P1024, P1025 and P4080) when MMC card used,
which is because these controllers does not support CMD23,
even on the SoCs which declares CMD23 is supported.
Therefore, we'll not use CMD23.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch removes the following warning.
drivers/mmc/host/dw_mmc.c:1976: warning: passing argument 1 of
'_dev_info' from incompatible pointer type
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This fetches the pinctrl resource for the MMCI driver, and if
a "default" state is found, it is activated.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For writes, HWFC shall be switched off when transfer size <= 8
bytes and when MCLK rate is above 50 MHz. For 50MHz and below
it shall be switched off when transfer size < 8 bytes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
