Devices which know that they are spares do not really need to have
an event count that matches the rest of the array, so there are no
data-in-sync issues. It is enough that the uuid matches.
So remove the requirement that the event count is up-to-date.
We currently still write out and event count on spares, but this
allows us in a year or 3 to stop doing that completely.
Signed-off-by: NeilBrown <neilb@suse.de>
When updating the event count for a simple clean <-> dirty transition,
we try to avoid updating the spares so they can safely spin-down.
As the event_counts across an array must be +/- 1, this means
decrementing the event_count on a dirty->clean transition.
This is not always safe and we have to avoid the unsafe time.
We current do this with a misguided idea about it being safe or
not depending on whether the event_count is odd or even. This
approach only works reliably in a few common instances, but easily
falls down.
So instead, simply keep internal state concerning whether it is safe
or not, and always assume it is not safe when an array is first
assembled.
Signed-off-by: NeilBrown <neilb@suse.de>
Some time ago we stopped the clean/active metadata updates
from being written to a 'spare' device in most cases so that
it could spin down and say spun down. Device failure/removal
etc are still recorded on spares.
However commit 51d5668cb2 broke this 50% of the time,
depending on whether the event count is even or odd.
The change log entry said:
This means that the alignment between 'odd/even' and
'clean/dirty' might take a little longer to attain,
how ever the code makes no attempt to create that alignment, so it
could take arbitrarily long.
So when we find that clean/dirty is not aligned with odd/even,
force a second metadata-update immediately. There are already cases
where a second metadata-update is needed immediately (e.g. when a
device fails during the metadata update). We just piggy-back on that.
Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Level modifications change the output of mdstat. The mdmon manager
thread is interested in these events for external metadata management.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This is
- unnecessary because mddev_suspend is always followed by a call to
->stop, and each ->stop unregisters the thread, and
- a problem as it makes it awkwards to suspend and then resume a
device as we will want later.
Signed-off-by: NeilBrown <neilb@suse.de>
We used to pass the personality make_request function direct
to the block layer so the first argument had to be a queue.
But now we have the intermediary md_make_request so it makes
at lot more sense to pass a struct mddev_s.
It makes it possible to have an mddev without its own queue too.
Signed-off-by: NeilBrown <neilb@suse.de>
This moves the call to the other side of set_readonly, but that should
not be an issue.
This encapsulates in 'md_stop' all of the functionality for internally
stopping the array, leaving all the interactions with externalities
(sysfs, request_queue, gendisk) in do_md_stop.
Signed-off-by: NeilBrown <neilb@suse.de>
Using do_md_stop to set an array to read-only is a little confusing.
Now most of the common code has been factored out, split
md_set_readonly off in to a separate function.
Signed-off-by: NeilBrown <neilb@suse.de>
Further refactoring of do_md_stop.
This one requires some explanation as it takes code from different
places in do_md_stop, so some re-ordering happens.
We only get into this part of do_md_stop if there are no active opens
of the device, so no writes can be happening and the device must have
been flushed. In md_stop_writes we want to stop any internal sources
of writes - i.e. resync - and flush out the metadata.
The only code that was previously before some of this code is
code to clean up the queue, the mddev, the gendisk, or sysfs, all
of which is probably better after code that makes active changes (i.e.
triggers writes).
Signed-off-by: NeilBrown <neilb@suse.de>
do_md_stop is large and clunky, so hard to understand.
This is a first step of refactoring, pulling two simple
sub-functions out.
Signed-off-by: NeilBrown <neilb@suse.de>
As part of relaxing the binding between an mddev and gendisk,
we separate do_md_run into two functions.
md_run does all the work internal to md
do_md_run calls md_run and makes and changes to gendisk
that are required.
Signed-off-by: NeilBrown <neilb@suse.de>
We set ->changed to 1 and call check_disk_change at the end
of md_open so that bd_invalidated would be set and thus
partition rescan would happen appropriately.
Now that we call revalidate_disk directly, which sets bd_invalidates,
that indirection is no longer needed and can be removed.
Signed-off-by: NeilBrown <neilb@suse.de>
Using ->array_sectors rather than get_capacity() is more
direct and is a step towards relaxing the tight connection
between mddev and gendisk.
Signed-off-by: NeilBrown <neilb@suse.de>
While I generally prefer letting personalities do as much as possible,
given that we have a central md_make_request anyway we may as well use
it to simplify code.
Also this centralises knowledge of ->gendisk which will help later.
Signed-off-by: NeilBrown <neilb@suse.de>
Level changes can be very significant, so make sure
to notify them via sysfs.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When metadata is being managed by user-space, md doesn't know
what the maximum number of devices allowed in an array is
so ->max_disks is 0. In this case we should allow any (+ve)
number of disks.
Signed-off-by: NeilBrown <neilb@suse.de>
Writing "none" to "../md/dev-xx/slot" removes that device
from being an active part of the array, but it didn't
set ->raid_disk to -1 to record this fact.
Signed-off-by: Maciej Trela <Maciej.Trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This was needed when sysfs files could only be 'notified'
from process context. Now that we have sys_notify_direct,
we can call it directly from an interrupt.
Signed-off-by: NeilBrown <neilb@suse.de>
Some levels expect the 'redundancy group' to be present,
others don't.
So when we change level of an array we might need to
add or remove this group.
This requires fixing up the current practice of overloading ->private
to indicate (when ->pers == NULL) that something needs to be removed.
So create a new ->to_remove to fill that role.
When changing levels, we may need to add or remove attributes. When
changing RAID5 -> RAID6, we both add and remove the same thing. It is
important to catch this and optimise it out as the removal is delayed
until a lock is released, so trying to add immediately would cause
problems.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When an array is stopped we need to remove some
sysfs files which are dependent on the type of array.
We need to delay that deletion as deleting them while holding
reconfig_mutex can lead to deadlocks.
We currently delay them until the array is completely destroyed.
However it is possible to deactivate and then reactivate the array.
It is also possible to need to remove sysfs files when changing level,
which can potentially happen several times before an array is
destroyed.
So we need to delete these files more promptly: as soon as
reconfig_mutex is dropped.
We need to ensure this happens before do_md_run can restart the array,
so we use open_mutex for some extra locking. This is not deadlock
prone.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When the user sets the block device to readwrite then the mddev should
follow suit. Otherwise, the BUG_ON in md_write_start() will be set to
trigger.
The reverse direction, setting mddev->ro to match a set readonly
request, can be ignored because the blkdev level readonly flag precludes
the need to have mddev->ro set correctly. Nevermind the fact that
setting mddev->ro to 1 may fail if the array is in use.
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Some time ago we stopped the clean/active metadata updates
from being written to a 'spare' device in most cases so that
it could spin down and say spun down. Device failure/removal
etc are still recorded on spares.
However commit 51d5668cb2 broke this 50% of the time,
depending on whether the event count is even or odd.
The change log entry said:
This means that the alignment between 'odd/even' and
'clean/dirty' might take a little longer to attain,
how ever the code makes no attempt to create that alignment, so it
could take arbitrarily long.
So when we find that clean/dirty is not aligned with odd/even,
force a second metadata-update immediately. There are already cases
where a second metadata-update is needed immediately (e.g. when a
device fails during the metadata update). We just piggy-back on that.
Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
======
This fix is related to
http://bugzilla.kernel.org/show_bug.cgi?id=15142
but does not address that exact issue.
======
sysfs does like attributes being removed while they are being accessed
(i.e. read or written) and waits for the access to complete.
As accessing some md attributes takes the same lock that is held while
removing those attributes a deadlock can occur.
This patch addresses 3 issues in md that could lead to this deadlock.
Two relate to calling flush_scheduled_work while the lock is held.
This is probably a bad idea in general and as we use schedule_work to
delete various sysfs objects it is particularly bad.
In one case flush_scheduled_work is called from md_alloc (called by
md_probe) called from do_md_run which holds the lock. This call is
only present to ensure that ->gendisk is set. However we can be sure
that gendisk is always set (though possibly we couldn't when that code
was originally written. This is because do_md_run is called in three
different contexts:
1/ from md_ioctl. This requires that md_open has succeeded, and it
fails if ->gendisk is not set.
2/ from writing a sysfs attribute. This can only happen if the
mddev has been registered in sysfs which happens in md_alloc
after ->gendisk has been set.
3/ from autorun_array which is only called by autorun_devices, which
checks for ->gendisk to be set before calling autorun_array.
So the call to md_probe in do_md_run can be removed, and the check on
->gendisk can also go.
In the other case flush_scheduled_work is being called in do_md_stop,
purportedly to wait for all md_delayed_delete calls (which delete the
component rdevs) to complete. However there really isn't any need to
wait for them - they have already been disconnected in all important
ways.
The third issue is that raid5->stop() removes some attribute names
while the lock is held. There is already some infrastructure in place
to delay attribute removal until after the lock is released (using
schedule_work). So extend that infrastructure to remove the
raid5_attrs_group.
This does not address all lockdep issues related to the sysfs
"s_active" lock. The rest can be address by splitting that lockdep
context between symlinks and non-symlinks which hopefully will happen.
Signed-off-by: NeilBrown <neilb@suse.de>
If two arrays share a device, then they will not both resync at the
same time. One will wait for the other to complete.
While waiting, the MD_RECOVERY_INTR flag is not checked so a device
failure, which would make the resync pointless, does not cause the
resync to abort, so the failed device cannot be removed (as it cannot
be remove while a resync is happening).
So add a test for MD_RECOVERY_INTR.
Reported-by: Brett Russ <bruss@netezza.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Since commit dfc7064500,
->hot_remove_disks has not removed non-failed devices from
an array until recovery is no longer possible.
So the code in do_md_run to get around the fact that
md_check_recovery (which calls ->hot_remove_disks) would
remove partially-in-sync devices is no longer needed.
So remove it.
Signed-off-by: NeilBrown <neilb@suse.de>
By default md_do_sync() will perform recovery if no other actions are
specified. However, action_show() relies on MD_RECOVERY_RECOVER to be
set otherwise it returns 'idle'. So, add a missing set
MD_RECOVERY_RECOVER when starting recovery.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The start_ro modules parameter can be used to force arrays to be
started in 'auto-readonly' in which they are read-only until the first
write. This ensures that no resync/recovery happens until something
else writes to the device. This is important for resume-from-disk
off an md array.
However if an array is started 'readonly' (by writing 'readonly' to
the 'array_state' sysfs attribute) we want it to be really 'readonly',
not 'auto-readonly'.
So strengthen the condition to only set auto-readonly if the
array is not already read-only.
Signed-off-by: NeilBrown <neilb@suse.de>
evms configures md arrays by:
open device
send ioctl
close device
for each different ioctl needed.
Since 2.6.29, the device can disappear after the 'close'
unless a significant configuration has happened to the device.
The change made by "SET_ARRAY_INFO" can too minor to stop the device
from disappearing, but important enough that losing the change is bad.
So: make sure SET_ARRAY_INFO sets mddev->ctime, and keep the device
active as long as ctime is non-zero (it gets zeroed with lots of other
things when the array is stopped).
This is suitable for -stable kernels since 2.6.29.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Makes use of skip_spaces() defined in lib/string.c for removing leading
spaces from strings all over the tree.
It decreases lib.a code size by 47 bytes and reuses the function tree-wide:
text data bss dec hex filename
64688 584 592 65864 10148 (TOTALS-BEFORE)
64641 584 592 65817 10119 (TOTALS-AFTER)
Also, while at it, if we see (*str && isspace(*str)), we can be sure to
remove the first condition (*str) as the second one (isspace(*str)) also
evaluates to 0 whenever *str == 0, making it redundant. In other words,
"a char equals zero is never a space".
Julia Lawall tried the semantic patch (http://coccinelle.lip6.fr) below,
and found occurrences of this pattern on 3 more files:
drivers/leds/led-class.c
drivers/leds/ledtrig-timer.c
drivers/video/output.c
@@
expression str;
@@
( // ignore skip_spaces cases
while (*str && isspace(*str)) { \(str++;\|++str;\) }
|
- *str &&
isspace(*str)
)
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Cc: Julia Lawall <julia@diku.dk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable external metadata arrays to manage rebuild checkpointing via a
md/dev-XXX/recovery_start attribute which reflects rdev->recovery_offset
Also update resync_start_store to allow 'none' to be written, for
consistency.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Other walks of this list are either under rcu_read_lock() or the list
mutation lock (mddev_lock()). This protects against the improbable case of a
disk being removed from the array at the start of md_do_sync().
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As v1.x metadata can record that a member of the array is
not completely recovered, it make sense to record that a
spare has become a regular member of the array at the earliest
opportunity.
So remove the tests on "recovery_offset > 0" in super_1_sync
as they really aren't needed, and schedule a metadata update
immediately after adding spares to a degraded array.
This means that if a crash happens immediately after a recovery
starts, the new device will be included in the array and recovery will
continue from wherever it was up to. Previously this didn't happen
unless recovery was at least 1/16 of the way through.
Signed-off-by: NeilBrown <neilb@suse.de>
The RAID ioctls are only implemented in md.c, so the
handling for them should also be moved there from
fs/compat_ioctl.c.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Neil Brown <neilb@suse.de>
Cc: Andre Noll <maan@systemlinux.org>
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
We've noticed severe lasting performance degradation of our raid
arrays when we have drives that yield large amounts of media errors.
The raid10 module will queue each failed read for retry, and also
will attempt call fix_read_error() to perform the read recovery.
Read recovery is performed while the array is frozen, so repeated
recovery attempts can degrade the performance of the array for
extended periods of time.
With this patch I propose adding a per md device max number of
corrected read attempts. Each rdev will maintain a count of
read correction attempts in the rdev->read_errors field (not
used currently for raid10). When we enter fix_read_error()
we'll check to see when the last read error occurred, and
divide the read error count by 2 for every hour since the
last read error. If at that point our read error count
exceeds the read error threshold, we'll fail the raid device.
In addition in this patch I add sysfs nodes (get/set) for
the per md max_read_errors attribute, the rdev->read_errors
attribute, and added some printk's to indicate when
fix_read_error fails to repair an rdev.
For testing I used debugfs->fail_make_request to inject
IO errors to the rdev while doing IO to the raid array.
Signed-off-by: Robert Becker <Rob.Becker@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
A new attribute directory 'bitmap' in 'md' is created which
contains files for configuring the bitmap.
'location' identifies where the bitmap is, either 'none',
or 'file' or 'sector offset from metadata'.
Writing 'location' can create or remove a bitmap.
Adding a 'file' bitmap this way is not yet supported.
'chunksize' and 'time_base' must be set before 'location'
can be set.
'chunksize' can be set before creating a bitmap, but is
currently always over-ridden by the bitmap superblock.
'time_base' and 'backlog' can be updated at any time.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Andre Noll <maan@systemlinux.org>
safe_delay_store can parse fixed point numbers (for fractions
of a second). We will want to do that for another sysfs
file soon, so factor out the code.
Signed-off-by: NeilBrown <neilb@suse.de>
... and into bitmap_info. These are all configuration parameters
that need to be set before the bitmap is created.
Signed-off-by: NeilBrown <neilb@suse.de>
In preparation for making bitmap fields configurable via sysfs,
start tidying up by making a single structure to contain the
configuration fields.
Signed-off-by: NeilBrown <neilb@suse.de>
Previously barriers were only supported on RAID1. This is because
other levels requires synchronisation across all devices and so needed
a different approach.
Here is that approach.
When a barrier arrives, we send a zero-length barrier to every active
device. When that completes - and if the original request was not
empty - we submit the barrier request itself (with the barrier flag
cleared) and then submit a fresh load of zero length barriers.
The barrier request itself is asynchronous, but any subsequent
request will block until the barrier completes.
The reason for clearing the barrier flag is that a barrier request is
allowed to fail. If we pass a non-empty barrier through a striping
raid level it is conceivable that part of it could succeed and part
could fail. That would be way too hard to deal with.
So if the first run of zero length barriers succeed, we assume all is
sufficiently well that we send the request and ignore errors in the
second run of barriers.
RAID5 needs extra care as write requests may not have been submitted
to the underlying devices yet. So we flush the stripe cache before
proceeding with the barrier.
Note that the second set of zero-length barriers are submitted
immediately after the original request is submitted. Thus when
a personality finds mddev->barrier to be set during make_request,
it should not return from make_request until the corresponding
per-device request(s) have been queued.
That will be done in later patches.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Andre Noll <maan@systemlinux.org>
If a resync/recovery/check/repair is interrupted for some reason, it
can be useful to know exactly where it got up to.
So in that case, do not clear curr_resync_completed.
Initialise it when starting a resync/recovery/... instead.
Signed-off-by: NeilBrown <neilb@suse.de>
When a 'check' or 'repair' finished we should clear resync_min
so that a future check/repair will cover the whole array (by default).
However if it is interrupted, we should update resync_min to
where we got up to, so that when the check/repair continues it
just does the remainder of the array.
Signed-off-by: NeilBrown <neilb@suse.de>
A write intent bitmap can be removed from an array while the
array is active.
When this happens, all IO is suspended and flushed before the
bitmap is removed.
However it is possible that bitmap_daemon_work is still running to
clear old bits from the bitmap. If it is, it can dereference the
bitmap after it has been freed.
So introduce a new mutex to protect bitmap_daemon_work and get it
before destroying a bitmap.
This is suitable for any current -stable kernel.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/sysctl-2.6: (43 commits)
security/tomoyo: Remove now unnecessary handling of security_sysctl.
security/tomoyo: Add a special case to handle accesses through the internal proc mount.
sysctl: Drop & in front of every proc_handler.
sysctl: Remove CTL_NONE and CTL_UNNUMBERED
sysctl: kill dead ctl_handler definitions.
sysctl: Remove the last of the generic binary sysctl support
sysctl net: Remove unused binary sysctl code
sysctl security/tomoyo: Don't look at ctl_name
sysctl arm: Remove binary sysctl support
sysctl x86: Remove dead binary sysctl support
sysctl sh: Remove dead binary sysctl support
sysctl powerpc: Remove dead binary sysctl support
sysctl ia64: Remove dead binary sysctl support
sysctl s390: Remove dead sysctl binary support
sysctl frv: Remove dead binary sysctl support
sysctl mips/lasat: Remove dead binary sysctl support
sysctl drivers: Remove dead binary sysctl support
sysctl crypto: Remove dead binary sysctl support
sysctl security/keys: Remove dead binary sysctl support
sysctl kernel: Remove binary sysctl logic
...
For consistency drop & in front of every proc_handler. Explicity
taking the address is unnecessary and it prevents optimizations
like stubbing the proc_handlers to NULL.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Resolve the conflict between v2.6.32-rc7 where dn_def_dev_handler
gets a small bug fix and the sysctl tree where I am removing all
sysctl strategy routines.
This is a combination that didn't really make sense before.
However when a reshape is converting e.g. raid5 -> raid6, the extra
device is not fully in-sync, but is certainly active and contains
important data.
So allow that start to be meaningful and in particular get
the 'recovery_offset' value (which is needed for any non-in-sync
active device) from the reshape_position.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that sys_sysctl is a wrapper around /proc/sys all of
the binary sysctl support elsewhere in the tree is
dead code.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Neil Brown <neilb@suse.de>
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de> for drivers/char/hpet.c
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Each device has its own 'recovery_offset' showing how far
recovery has progressed on the device.
As the only real significance of this is that fact that it can
be stored in the metadata and recovered at restart, and as
only 1.x metadata can do this, we were only updating
'recovery_offset' to 'curr_resync_completed' when updating
v1.x metadata.
But this is wrong, and we will shortly make limited use of this
field in v0.90 metadata.
So move the update into common code.
Signed-off-by: NeilBrown <neilb@suse.de>
If a 'sync_max' has been set (via sysfs), it is wrong to clear it
until a resync (or reshape or recovery ...) actually reached that
point.
So if a resync is interrupted (e.g. by device failure),
leave 'resync_max' unchanged.
This is particularly important for 'reshape' operations that do not
change the size of the array. For such operations mdadm needs to
monitor the reshape taking rolling backups of the section being
reshaped. If resync_max gets cleared, the reshape can get ahead of
mdadm and then the backups that mdadm creates are useless.
This is suitable for 2.6.31.y stable kernels.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When a raid5 (or raid6) array is being reshaped to have fewer devices,
conf->raid_disks is the latter and hence smaller number of devices.
However sometimes we want to use a number which is the total number of
currently required devices - the larger of the 'old' and 'new' sizes.
Before we implemented reducing the number of devices, this was always
'new' i.e. ->raid_disks.
Now we need max(raid_disks, previous_raid_disks) in those places.
This particularly affects assembling an array that was shutdown while
in the middle of a reshape to fewer devices.
md.c needs a similar fix when interpreting the md metadata.
Signed-off-by: NeilBrown <neilb@suse.de>
The management thread for raid4,5,6 arrays are all called
mdX_raid5, independent of the actual raid level, which is wrong and
can be confusion.
So change md_register_thread to use the name from the personality
unless no alternate name (like 'resync' or 'reshape') is given.
This is simpler and more correct.
Cc: Jinzc <zhenchengjin@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Rename some variable and remove some duplicate definitions
to avoid there warnings. None of them are actual errors.
Signed-off-by: NeilBrown <neilb@suse.de>
Recent commit c8c00a6915
changed the exit paths in do_md_stop and was not quite
careful enough. There is one path were 'err' now needs
to be cleared but it isn't.
So setting an array to readonly (with mdadm --readonly) will
work, but will incorrectly report and error: ENXIO.
Signed-off-by: NeilBrown <neilb@suse.de>
Normally we only allow the upper limit for a reshape to be decreased
when the array not performing a sync/recovery/reshape, otherwise there
could be races. But if an array is part-way through a reshape when it
is assembled the reshape is started immediately leaving no window
to set an upper bound.
If the array is started read-only, the reshape will be suspended until
the array becomes writable, so that provides a window during which it
is perfectly safe to reduce the upper limit of a reshape.
So: allow the upper limit (sync_max) to be reduced even if the reshape
thread is running, as long as the array is still read-only.
Signed-off-by: NeilBrown <neilb@suse.de>
When assembling arrays, md allows two devices to have different event
counts as long as the difference is only '1'. This is to cope with
a system failure between updating the metadata on two difference
devices.
However there are currently times when we update the event count by
2. This was done to keep the event count even when the array is clean
and odd when it is dirty, which allows us to avoid writing common
update to spare devices and so allow those spares to go to sleep.
This is bad for the above reason. So change it to never increase by
two. This means that the alignment between 'odd/even' and
'clean/dirty' might take a little longer to attain, but that is only a
small cost. The spares will get a few more updates but that will
still be spared (;-) most updates and can still go to sleep.
Prior to this patch there was a small chance that after a crash an
array would fail to assemble due to the overly large event count
mismatch.
Signed-off-by: NeilBrown <neilb@suse.de>
A recent commit:
commit 449aad3e25
introduced the possibility of an A-B/B-A deadlock between
bd_mutex and reconfig_mutex.
__blkdev_get holds bd_mutex while calling md_open which takes
reconfig_mutex,
do_md_run is always called with reconfig_mutex held, and it now
takes bd_mutex in the call the revalidate_disk.
This potential deadlock was not caught by lockdep due to the
use of mutex_lock_interruptible_nexted which was introduced
by
commit d63a5a74de
do avoid a warning of an impossible deadlock.
It is quite possible to split reconfig_mutex in to two locks.
One protects the array data structures while it is being
reconfigured, the other ensures that an array is never even partially
open while it is being deactivated.
In particular, the second lock prevents an open from completing
between the time when do_md_stop checks if there are any active opens,
and the time when the array is either set read-only, or when ->pers is
set to NULL. So we can be certain that no IO is in flight as the
array is being destroyed.
So create a new lock, open_mutex, just to ensure exclusion between
'open' and 'stop'.
This avoids the deadlock and also avoids the lockdep warning mentioned
in commit d63a5a74d
Reported-by: "Mike Snitzer" <snitzer@gmail.com>
Reported-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NeilBrown <neilb@suse.de>
As revalidate_disk calls check_disk_size_change, it will cause
any capacity change of a gendisk to be propagated to the blockdev
inode. So use that instead of mucking about with locks and
i_size_write.
Also add a call to revalidate_disk in do_md_run and a few other places
where the gendisk capacity is changed.
Signed-off-by: NeilBrown <neilb@suse.de>
The v1.x metadata does not have a fixed size and can grow
when devices are added.
If it grows enough to require an extra sector of storage,
we need to update the 'sb_size' to match.
Without this, md can write out an incomplete superblock with a
bad checksum, which will be rejected when trying to re-assemble
the array.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
We trust the 'desc_nr' field in v1.x metadata enough to use it
as an index in an array. This isn't really safe.
So range-check the value first.
Signed-off-by: NeilBrown <neilb@suse.de>
When an array is changed from RAID6 to RAID5, fewer drives are
needed. So any device that is made superfluous by the level
conversion must be marked as not-active.
For the RAID6->RAID5 conversion, this will be a drive which only
has 'Q' blocks on it.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
This patch replaces md_integrity_check() by two new public functions:
md_integrity_register() and md_integrity_add_rdev() which are both
personality-independent.
md_integrity_register() is called from the ->run and ->hot_remove
methods of all personalities that support data integrity. The
function iterates over the component devices of the array and
determines if all active devices are integrity capable and if their
profiles match. If this is the case, the common profile is registered
for the mddev via blk_integrity_register().
The second new function, md_integrity_add_rdev() is called from the
->hot_add_disk methods, i.e. whenever a new device is being added
to a raid array. If the new device does not support data integrity,
or has a profile different from the one already registered, data
integrity for the mddev is disabled.
For raid0 and linear, only the call to md_integrity_register() from
the ->run method is necessary.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
User space can set various limits on an md array so that resync waits
when it gets to a certain point, or so that I/O is blocked for a short
while.
When md is waiting against one of these limit, it should use an
interruptible wait so as not to add to the load average, and so are
not to trigger a warning if the wait goes on for too long.
Signed-off-by: NeilBrown <neilb@suse.de>
As the recent bug in md_alloc showed, having a single exit path for
unlocking and putting is a good idea. So restructure md_alloc to have
a single mutex_unlock and mddev_put, and use gotos where necessary.
Found-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When an md device is created by name (rather than number) we need to
check that the name is not already in use. If this check finds a
duplicate, we return an error without dropping the lock or freeing
the newly create mddev.
This patch fixes that.
Cc: stable@kernel.org
Found-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If we try to modify one of the md/ sysfs files
suspend_lo or suspend_hi
when the array is not active, we dereference a NULL.
Protect against that.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
If the superblock of a component device indicates the presence of a
bitmap but the corresponding raid personality does not support bitmaps
(raid0, linear, multipath, faulty), then something is seriously wrong
and we'd better refuse to run such an array.
Currently, this check is performed while the superblocks are examined,
i.e. before entering personality code. Therefore the generic md layer
must know which raid levels support bitmaps and which do not.
This patch avoids this layer violation without adding identical code
to various personalities. This is accomplished by introducing a new
public function to md.c, md_check_no_bitmap(), which replaces the
hard-coded checks in the superblock loading functions.
A call to md_check_no_bitmap() is added to the ->run method of each
personality which does not support bitmaps and assembly is aborted
if at least one component device contains a bitmap.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
It is easiest to round sizes to multiples of chunk size in
the personality code for those personalities which care.
Those personalities now do the rounding, so we can
remove that function from common code.
Also remove the upper bound on the size of a chunk, and the lower
bound on the size of a device (1 chunk), neither of which really buy
us anything.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently the assignment to utime gets skipped for 'external'
metadata. So move it to the top of the function so that it
always gets effected.
This is of largely cosmetic interest. Nothing actually depends
on ->utime being right for external arrays.
"mdadm --monitor" does use it for 0.90 and 1.x arrays, but with
mdadm-3.0, this is not important for external metadata.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently, the md layer checks in analyze_sbs() if the raid level
supports reconstruction (mddev->level >= 1) and if reconstruction is
in progress (mddev->recovery_cp != MaxSector).
Move that printk into the personality code of those raid levels that
care (levels 1, 4, 5, 6, 10).
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
The difference between these two methods is artificial.
Both check that a pending reshape is valid, and perform any
aspect of it that can be done immediately.
'reconfig' handles chunk size and layout.
'check_reshape' handles raid_disks.
So make them just one method.
Signed-off-by: NeilBrown <neilb@suse.de>
Passing the new layout and chunksize as args is not necessary as
the mddev has fields for new_check and new_layout.
This is preparation for combining the check_reshape and reconfig
methods
Signed-off-by: NeilBrown <neilb@suse.de>
A straight-forward conversion which gets rid of some
multiplications/divisions/shifts. The patch also introduces a couple
of new ones, most of which are due to conf->chunk_size still being
represented in bytes. This will be cleaned up in subsequent patches.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the chunk_size field to chunk_sectors with the
implied change of semantics. Since
is_power_of_2(chunk_size) = is_power_of_2(chunk_sectors << 9)
= is_power_of_2(chunk_sectors)
these bits don't need an adjustment for the shift.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Remove chunk size check from md as this is now performed in the run
function in each personality.
Replace chunk size power 2 code calculations by a regular division.
Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
In order for the metadata to always be consistent, we mustn't updated
curr_resync_completed without also updating reshape_position.
The reshape code updates both at the same time. However since
commit 97e4f42d62
the common md_do_sync will sometimes update curr_resync_completed
but is not in a position to update reshape_position.
So if MD_RECOVERY_RESHAPE is set (indicating that a reshape is
happening, so reshape_position might change), don't update
curr_resync_completed in md_do_sync, leave it to the per-personality
reshape code.
Signed-off-by: NeilBrown <neilb@suse.de>
The md resync engine has a 'frozen' state which ensures that
no resync/recovery. This is used to avoid races.
Export this state through the 'sync_action' sysfs attribute
so that user-space can benefit and also avoid some races.
Signed-off-by: NeilBrown <neilb@suse.de>
Instead of always returns EINVAL if anything goes wrong
when setting the array size, add the option of
E2BIG
if the size requested is too large. This makes it easier
for user-space to be sure what went wrong.
Signed-off-by: NeilBrown <neilb@suse.de>
We previously didn't update these fields when writing the metadata
because they could never change. They can now, so we better write
them.
v0.90 metadata always updated these fields.
Signed-off-by: NeilBrown <neilb@suse.de>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
md maintains link in sys/mdXX/md/ to identify which device has
which role in the array. e.g.
rd2 -> dev-sda
indicates that the device with role '2' in the array is sda.
These links are only present when the array is active. They are
created immediately after ->run is called, and so should be removed
immediately after ->stop is called.
However they are currently removed a little bit later, and it is
possible for ->run to be called again, thus adding these links, before
they are removed.
So move the removal earlier so they are consistently only present when
the array is active.
Signed-off-by: NeilBrown <neilb@suse.de>
Being able to write 'clean' to an 'array_state' of an inactive array
to activate it in 'clean' mode is both unnecessary and inconvenient.
It is unnecessary because the same can be achieved by writing
'active'. This activates and array, but it still remains 'clean'
until the first write.
It is inconvenient because writing 'clean' is more often used to
cause an 'active' array to revert to 'clean' mode (thus blocking
any writes until a 'write-pending' is promoted to 'active').
Allowing 'clean' to both activate an array and mark an active array as
clean can lead to races: One program writes 'clean' to mark the
active array as clean at the same time as another program writes
'inactive' to deactivate (stop) and active array. Depending on which
writes first, the array could be deactivated and immediately
reactivated which isn't what was desired.
So just disable the use of 'clean' to activate an array.
This avoids a race that can be triggered with mdadm-3.0 and external
metadata, so it suitable for -stable.
Reported-by: Rafal Marszewski <rafal.marszewski@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Two problems in status_resync.
1/ It still used Kilobytes as the basic block unit, while most code
now uses sectors uniformly.
2/ It doesn't allow for the possibility that max_sectors exceeds
the range of "unsigned long".
So
- change "max_blocks" to "max_sectors", and store sector numbers
in there and in 'resync'
- Make 'rt' a 'sector_t' so it can temporarily hold the number of
remaining sectors.
- use sector_div rather than normal division.
- change the magic '100' used to preserve precision to '32'.
+ making it a power of 2 makes division easier
+ it doesn't need to be as large as it was chosen when we averaged
speed over the entire run. Now we average speed over the last 30
seconds or so.
Reported-by: "Mario 'BitKoenig' Holbe" <Mario.Holbe@TU-Ilmenau.DE>
Signed-off-by: NeilBrown <neilb@suse.de>
There are circumstances when a user-space process might need to
"oversee" a resync/reshape process. For example when doing an
in-place reshape of a raid5, it is prudent to take a backup of each
section before reshaping it as this is the only way to provide
safety against an unplanned shutdown (i.e. crash/power failure).
The sync_max sysfs value can be used to stop the resync from
advancing beyond a particular point.
So user-space can:
suspend IO to the first section and back it up
set 'sync_max' to the end of the section
wait for 'sync_completed' to reach that point
resume IO on the first section and move on to the next section.
However this process requires the kernel and user-space to run in
lock-step which could introduce unnecessary delays.
It would be better if a 'double buffered' approach could be used with
userspace and kernel space working on different sections with the
'next' section always ready when the 'current' section is finished.
One problem with implementing this is that sync_completed is only
guaranteed to be updated when the sync process reaches sync_max.
(it is updated on a time basis at other times, but it is hard to rely
on that). This defeats some of the double buffering.
With this patch, sync_completed (and reshape_position) get updated as
the current position approaches sync_max, so there is room for
userspace to advance sync_max early without losing updates.
To be precise, sync_completed is updated when the current sync
position reaches half way between the current value of sync_completed
and the value of sync_max. This will usually be a good time for user
space to update sync_max.
If sync_max does not get updated, the updates to sync_completed
(together with associated metadata updates) will occur at an
exponentially increasing frequency which will get unreasonably fast
(one update every page) immediately before the process hits sync_max
and stops. So the update rate will be unreasonably fast only for an
insignificant period of time.
Signed-off-by: NeilBrown <neilb@suse.de>
The sync_completed file reports how much of a resync (or recovery or
reshape) has been completed.
However due to the possibility of out-of-order completion of writes,
it is not certain to be accurate.
We have an internal value - mddev->curr_resync_completed - which is an
accurate value (though it might not always be quite so uptodate).
So:
- make curr_resync_completed be uptodate a little more often,
particularly when raid5 reshape updates status in the metadata
- report curr_resync_completed in the sysfs file
- allow poll/select to report all updates to md/sync_completed.
This makes sync_completed completed usable by any external metadata
handler that wants to record this status information in its metadata.
Signed-off-by: NeilBrown <neilb@suse.de>
When adding devices to an active array via sysfs, there is currently
no way to mark a device as 'in-sync' which is useful when
incrementally assembling an array.
So add that option.
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-linus' of git://neil.brown.name/md: (53 commits)
md/raid5 revise rules for when to update metadata during reshape
md/raid5: minor code cleanups in make_request.
md: remove CONFIG_MD_RAID_RESHAPE config option.
md/raid5: be more careful about write ordering when reshaping.
md: don't display meaningless values in sysfs files resync_start and sync_speed
md/raid5: allow layout and chunksize to be changed on active array.
md/raid5: reshape using largest of old and new chunk size
md/raid5: prepare for allowing reshape to change layout
md/raid5: prepare for allowing reshape to change chunksize.
md/raid5: clearly differentiate 'before' and 'after' stripes during reshape.
Documentation/md.txt update
md: allow number of drives in raid5 to be reduced
md/raid5: change reshape-progress measurement to cope with reshaping backwards.
md: add explicit method to signal the end of a reshape.
md/raid5: enhance raid5_size to work correctly with negative delta_disks
md/raid5: drop qd_idx from r6_state
md/raid6: move raid6 data processing to raid6_pq.ko
md: raid5 run(): Fix max_degraded for raid level 4.
md: 'array_size' sysfs attribute
md: centralize ->array_sectors modifications
...
When no resync if happening, both of these files currently have
meaningless values (is slightly different ways).
Change them to "none" in that case.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently raid5 (the only module that supports restriping)
notices that the reshape has finished be sync_request being
given a large value, and handles any cleanup them.
This patch changes it so md_check_recovery calls into an
explicit finish_reshape method as well.
The clean-up from sync_request can do things that need to be
done promptly, typically things local to the raid5_conf_t
structure.
The "finish_reshape" method is called under the mddev_lock
so it can do things involving reconfiguring the device.
This allows us to get rid of md_set_array_sectors_locked, which
would have caused a deadlock if you tried to stop and array
while a reshape was happening.
Signed-off-by: NeilBrown <neilb@suse.de>
Allow userspace to set the size of the array according to the following
semantics:
1/ size must be <= to the size returned by mddev->pers->size(mddev, 0, 0)
a) If size is set before the array is running, do_md_run will fail
if size is greater than the default size
b) A reshape attempt that reduces the default size to less than the set
array size should be blocked
2/ once userspace sets the size the kernel will not change it
3/ writing 'default' to this attribute returns control of the size to the
kernel and reverts to the size reported by the personality
Also, convert locations that need to know the default size from directly
reading ->array_sectors to <pers>_size. Resync/reshape operations
always follow the default size.
Finally, fixup other locations that read a number of 1k-blocks from
userspace to use strict_blocks_to_sectors() which checks for unsigned
long long to sector_t overflow and blocks to sectors overflow.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Get personalities out of the business of directly modifying
->array_sectors. Lays groundwork to introduce policy on when
->array_sectors can be modified.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2-drive raid5's aren't very interesting. But if you are converting
a raid1 into a raid5, you will at least temporarily have one. And
that it a good time to set the layout/chunksize for the new RAID5
if you aren't happy with the defaults.
layout and chunksize don't actually affect the placement of data
on a 2-drive raid5, so we just do some internal book-keeping.
Signed-off-by: NeilBrown <neilb@suse.de>
Implement this for RAID6 to be able to 'takeover' a RAID5 array. The
new RAID6 will use a layout which places Q on the last device, and
that device will be missing.
If there are any available spares, one will immediately have Q
recovered onto it.
Signed-off-by: NeilBrown <neilb@suse.de>
To be able to change the 'level' of an md/raid array, we need to
suspend the device so that no requests are active - then move some
pointers around etc.
The code already keeps counts of active requests and the ->quiesce
function can be used to wait until those counts hit zero.
However the quiesce function blocks new requests once they are all
ready 'inside' the personality module, and that is too late if we want
to replace the personality modules.
So make all md requests come in through a common md_make_request
function that keeps track of how many requests have entered the
modules but may not yet be on the internal reference counts.
Allow md_make_request to be blocked when we want to suspend the
device, and make it possible to wait for all those in-transit requests
to be added to internal lists so that ->quiesce can wait for them.
There is still a problem that when a request completes, we drop the
ref count inside the personality code so there is a short time between
when the refcount hits zero, and when the personality code is no
longer being used.
The personality code never blocks (schedule or spinlock) between
dropping the refcount and exiting the routine, so this should be safe
(as put_module calls synchronize_sched() before unmapping the module
code).
Signed-off-by: NeilBrown <neilb@suse.de>
Mostly md_unregister_thread is only called when we know that the
thread is NULL, but sometimes we need to check first. It is safer
to put the check inside md_unregister_thread itself.
Signed-off-by: NeilBrown <neilb@suse.de>
When an md array is undergoing a change, we have new_* fields that
show the new values.
When no change is happening, it is least confusing if these have
the same value as the normal fields.
This is true in most cases, but not when the values are set via sysfs.
So fix this up.
A subsequent patch will BUG_ON if these things aren't consistent.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the "size" field of struct mdk_rdev_s to
"sectors" and changes this field to store sectors instead of
blocks.
All users of this field, linear.c, raid0.c and md.c, are fixed up
accordingly which gets rid of many multiplications and divisions.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the "size" field of struct mddev_s to "dev_sectors"
and stores the number of 512-byte sectors instead of the number of
1K-blocks in it.
All users of that field, including raid levels 1,4-6,10, are adjusted
accordingly. This simplifies the code a bit because it allows to get
rid of a couple of divisions/multiplications by two.
In order to make checkpatch happy, some minor coding style issues
have also been addressed. In particular, size_store() now uses
strict_strtoull() instead of simple_strtoull().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
When a drive is added to an array using ADD_NEW_DISK, there are two
places we can get certain flags from: the metadata on the disk or the
flags passed through the IOCTL.
For the WriteMostly flag (aka MD_DISK_WRITEMOSTLY) we take the value
from either of those sources depending on if it is set (i.e. we
effectively 'or' the two sources together).
This makes it awkward to clear, and is at best inconsistent.
As documented code (in mdadm) requires that setting
MD_DISK_WRITEMOSTLY in the ioctl will be effective, we resolve the
inconsistency by always using the value for this flag from the ioctl,
and ignoring the value on disk.
Signed-off-by: NeilBrown <neilb@suse.de>
Version 1.x metadata has the ability to record the status of a
partially completed drive recovery.
However we only update that record on a clean shutdown.
It would be nice to update it on unclean shutdowns too, particularly
when using a bitmap that removes much to the 'sync' effort after an
unclean shutdown.
One complication with checkpointing recovery is that we only know
where we are up to in terms of IO requests started, not which ones
have completed. And we need to know what has completed to record
how much is recovered. So occasionally pause the recovery until all
submitted requests are completed, then update the record of where
we are up to.
When we have a bitmap, we already do that pause occasionally to keep
the bitmap up-to-date. So enhance that code to record the recovery
offset and schedule a superblock update.
And when there is no bitmap, just pause 16 times during the resync to
do a checkpoint.
'16' is a fairly arbitrary number. But we don't really have any good
way to judge how often is acceptable, and it seems like a reasonable
number for now.
Signed-off-by: NeilBrown <neilb@suse.de>
This makes the includes more explicit, and is preparation for moving
md_k.h to drivers/md/md.h
Remove include/raid/md.h as its only remaining use was to #include
other files.
Signed-off-by: NeilBrown <neilb@suse.de>
.. as they are part of the user-space interface.
Also move MdpMinorShift into there so we can remove duplication.
Lastly move mdp_major in. It is less obviously part of the user-space
interface, but do_mounts_md.c uses it, and it is acting a bit like
user-space.
Signed-off-by: NeilBrown <neilb@suse.de>
Move the headers with the local structures for the disciplines and
bitmap.h into drivers/md/ so that they are more easily grepable for
hacking and not far away. md.h is left where it is for now as there
are some uses from the outside.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
MAJOR_NR was only required for magic in linux/blk.h in 2.4 or earlier
kernels, so no need to keep it around.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
md: Add support for data integrity to MD
If all subdevices support the same protection format the MD device is
flagged as integrity capable.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
There are two problems with is_mddev_idle.
1/ sync_io is 'atomic_t' and hence 'int'. curr_events and all the
rest are 'long'.
So if sync_io were to wrap on a 64bit host, the value of
curr_events would go very negative suddenly, and take a very
long time to return to positive.
So do all calculations as 'int'. That gives us plenty of precision
for what we need.
2/ To initialise rdev->last_events we simply call is_mddev_idle, on
the assumption that it will make sure that last_events is in a
suitable range. It used to do this, but now it does not.
So now we need to be more explicit about initialisation.
Signed-off-by: NeilBrown <neilb@suse.de>
We can't OR shift values, so get rid of BIO_RW_SYNC and use BIO_RW_SYNCIO
and BIO_RW_UNPLUG explicitly. This brings back the behaviour from before
213d9417fe.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Each different metadata format supported by md supports a
different maximum number of devices.
We really should be enforcing this maximum in the kernel, but
we aren't quite doing that properly.
We currently only enforce it at the 'hot_add' point, which is an
older interface which is not used by current userspace.
We need to also enforce it at 'add_new_disk' time for active arrays
and at 'do_md_run' time when starting a new array.
So move the test from 'hot_add' into 'bind_rdev_to_array' which is
called from both 'hot_add' and 'add_new_disk, and add a new
test in 'analyse_sbs' which is called from 'do_md_run'.
This bug (or missing feature) has been around "forever" and so
the patch is suitable for any -stable that is currently maintained.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
If a raid1 has only one working drive and it has a sector which
gives an error on read, then an attempt to recover onto a spare will
fail, but as the single remaining drive is not removed from the
array, the recovery will be immediately re-attempted, resulting
in an infinite recovery loop.
So detect this situation and don't retry recovery once an error
on the lone remaining drive is detected.
Allow recovery to be retried once every time a spare is added
in case the problem wasn't actually a media error.
Signed-off-by: NeilBrown <neilb@suse.de>
Using sequential numbers to identify md devices is somewhat artificial.
Using names can be a lot more user-friendly.
Also, creating md devices by opening the device special file is a bit
awkward.
So this patch provides a new option for creating and naming devices.
Writing a name such as "md_home" to
/sys/modules/md_mod/parameters/new_array
will cause an array with that name to be created. It will appear in
/sys/block/ /proc/partitions and /proc/mdstat as 'md_home'.
It will have an arbitrary minor number allocated.
md devices that a created by an open are destroyed on the last
close when the device is inactive.
For named md devices, they will not be destroyed until the array
is explicitly stopped, either with the STOP_ARRAY ioctl or by
writing 'clear' to /sys/block/md_XXXX/md/array_state.
The name of the array must start 'md_' to avoid conflict with
other devices.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently md devices, once created, never disappear until the module
is unloaded. This is essentially because the gendisk holds a
reference to the mddev, and the mddev holds a reference to the
gendisk, this a circular reference.
If we drop the reference from mddev to gendisk, then we need to ensure
that the mddev is destroyed when the gendisk is destroyed. However it
is not possible to hook into the gendisk destruction process to enable
this.
So we drop the reference from the gendisk to the mddev and destroy the
gendisk when the mddev gets destroyed. However this has a
complication.
Between the call
__blkdev_get->get_gendisk->kobj_lookup->md_probe
and the call
__blkdev_get->md_open
there is no obvious way to hold a reference on the mddev any more, so
unless something is done, it will disappear and gendisk will be
destroyed prematurely.
Also, once we decide to destroy the mddev, there will be an unlockable
moment before the gendisk is unlinked (blk_unregister_region) during
which a new reference to the gendisk can be created. We need to
ensure that this reference can not be used. i.e. the ->open must
fail.
So:
1/ in md_probe we set a flag in the mddev (hold_active) which
indicates that the array should be treated as active, even
though there are no references, and no appearance of activity.
This is cleared by md_release when the device is closed if it
is no longer needed.
This ensures that the gendisk will survive between md_probe and
md_open.
2/ In md_open we check if the mddev we expect to open matches
the gendisk that we did open.
If there is a mismatch we return -ERESTARTSYS and modify
__blkdev_get to retry from the top in that case.
In the -ERESTARTSYS sys case we make sure to wait until
the old gendisk (that we succeeded in opening) is really gone so
we loop at most once.
Some udev configurations will always open an md device when it first
appears. If we allow an md device that was just created by an open
to disappear on an immediate close, then this can race with such udev
configurations and result in an infinite loop the device being opened
and closed, then re-open due to the 'ADD' even from the first open,
and then close and so on.
So we make sure an md device, once created by an open, remains active
at least until some md 'ioctl' has been made on it. This means that
all normal usage of md devices will allow them to disappear promptly
when not needed, but the worst that an incorrect usage will do it
cause an inactive md device to be left in existence (it can easily be
removed).
As an array can be stopped by writing to a sysfs attribute
echo clear > /sys/block/mdXXX/md/array_state
we need to use scheduled work for deleting the gendisk and other
kobjects. This allows us to wait for any pending gendisk deletion to
complete by simply calling flush_scheduled_work().
Signed-off-by: NeilBrown <neilb@suse.de>
md_free is the .release handler for the md kobj_type.
So it makes sense to release all the objects referenced by
the mddev in there, rather than just prior to calling kobject_put
for what we think is the last time.
Signed-off-by: NeilBrown <neilb@suse.de>
It is more balanced to just do simple initialisation in mddev_find,
which allocates and links a new md device, and leave all the
more sophisticated allocation to md_probe (which calls mddev_find).
md_probe already allocated the gendisk. It should allocate the
queue too.
Signed-off-by: NeilBrown <neilb@suse.de>
The rdev_for_each macro defined in <linux/raid/md_k.h> is identical to
list_for_each_entry_safe, from <linux/list.h>, it should be defined to
use list_for_each_entry_safe, instead of reinventing the wheel.
But some calls to each_entry_safe don't really need a safe version,
just a direct list_for_each_entry is enough, this could save a temp
variable (tmp) in every function that used rdev_for_each.
In this patch, most rdev_for_each loops are replaced by list_for_each_entry,
totally save many tmp vars; and only in the other situations that will call
list_del to delete an entry, the safe version is used.
Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
There is no compelling need for this, but sysfs_notify_dirent is a
nicer interface and the change is good for consistency.
Signed-off-by: NeilBrown <neilb@suse.de>
It turns out that it is only safe to call blkdev_ioctl when the device
is actually open (as ->bd_disk is set to NULL on last close). And it
is quite possible for do_md_stop to be called when the device is not
open. So discard the call to blkdev_ioctl(BLKRRPART) which was
added in
commit 934d9c23b4
It is just as easy to call this ioctl from userspace when needed (on
mdadm -S) so leave it out of the kernel
Signed-off-by: NeilBrown <neilb@suse.de>
md arrays are not currently destroyed when they are stopped - they
remain in /sys/block. Last time I tried this I tripped over locking
too much.
A consequence of this is that udev doesn't remove anything from /dev.
This is rather ugly.
As an interim measure until proper device removal can be achieved,
make sure all partitions are removed using the BLKRRPART ioctl, and
send a KOBJ_CHANGE when an md array is stopped.
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-linus' of git://neil.brown.name/md:
md: allow extended partitions on md devices.
md: use sysfs_notify_dirent to notify changes to md/dev-xxx/state
md: use sysfs_notify_dirent to notify changes to md/array_state
To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The new extended partition support provides a much nicer was
to have partitions on md devices that the 'mdp' alternate major.
We cannot really get rid of 'mdp' at this time, but we can
enable extended partitions as that will probably make life
easier for sysadmins.
Signed-off-by: NeilBrown <neilb@suse.de>
The 'state' file for a device reports, for example, when the device
has failed. Changes should be reported to userspace ASAP without
the possibility of blocking on low-memory. sysfs_notify does
have that possibility (as it takes a mutex which can be held
across a kmalloc) so use sysfs_notify_dirent instead.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that we have sysfs_notify_dirent, use it to notify changes
to md/array_state.
As sysfs_notify_dirent can be called in atomic context, we can
remove the delayed notify and the MD_NOTIFY_ARRAY_STATE flag.
Signed-off-by: NeilBrown <neilb@suse.de>
safe_delay_store() currently truncates the last character of input since
it tells strlcpy that the buffer can only hold 'len' characters, off by
one. sysfs already null terminates the buffer, so just increase the
last argument to strlcpy.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Today's linux-next build (powerpc ppc64_defconfig) failed like this:
drivers/md/raid1.c: In function 'sync_request':
drivers/md/raid1.c:1759: error: implicit declaration of function 'msleep_interruptible'
make[3]: *** [drivers/md/raid1.o] Error 1
make[3]: *** Waiting for unfinished jobs....
drivers/md/raid10.c: In function 'sync_request':
drivers/md/raid10.c:1749: error: implicit declaration of function 'msleep_interruptible'
make[3]: *** [drivers/md/raid10.o] Error 1
drivers/md/md.c: In function 'md_do_sync':
drivers/md/md.c:5915: error: implicit declaration of function 'msleep'
Caused by commit 6caa3b0bbdb474647f6bdd8a958ffc46f78d8d58 ("md: Remove
unnecessary #includes, #defines, and function declarations"). I added
the following patch.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently, the 'chunk_size' of an array must be at-least PAGE_SIZE.
This makes moving an array to a machine with a larger PAGE_SIZE, or
changing the kernel to use a larger PAGE_SIZE, can stop an array from
working.
For RAID10 and RAID4/5/6, this is non-trivial to fix as the resync
process works on whole pages at a time, and assumes them to be wholly
within a stripe. For other raid personalities, this restriction is
not needed at all and can be dropped.
So remove the test on chunk_size from common can, and add it in just
the places where it is needed: raid10 and raid4/5/6.
Signed-off-by: NeilBrown <neilb@suse.de>
Having
function (args)
instead of
function(args)
make is harder to search for calls of particular functions.
So remove all those spaces.
Signed-off-by: NeilBrown <neilb@suse.de>
'read-auto' is a variant of 'readonly' which will switch to writable
on the first write attempt.
Calling do_md_stop to set the array readonly when it is already readonly
returns an error. So make sure not to do that.
Signed-off-by: NeilBrown <neilb@suse.de>
For externally managed metadata, the 'metadata_version' sysfs
attribute is really just a channel for user-space programs to
communicate about how the array is being managed.
It can be useful for this to be changed while the array is active.
Normally changes to metadata_version are not permitted while the array
is active. Change that so that if the metadata is externally managed,
the metadata_version can be changed to a different flavour of external
management.
Signed-off-by: NeilBrown <neilb@suse.de>
Fix rdev_size_store with size == 0.
size == 0 means to use the largest size allowed by the
underlying device and is used when modifying an active array.
This fixes a regression introduced by
commit d7027458d6
Cc: <stable@kernel.org>
Signed-off-by: Chris Webb <chris@arachsys.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Move stats related fields - stamp, in_flight, dkstats - from disk to
part0 and unify stat handling such that...
* part_stat_*() now updates part0 together if the specified partition
is not part0. ie. part_stat_*() are now essentially all_stat_*().
* {disk|all}_stat_*() are gone.
* part_round_stats() is updated similary. It handles part0 stats
automatically and disk_round_stats() is killed.
* part_{inc|dec}_in_fligh() is implemented which automatically updates
part0 stats for parts other than part0.
* disk_map_sector_rcu() is updated to return part0 if no part matches.
Combined with the above changes, this makes NULL special case
handling in callers unnecessary.
* Separate stats show code paths for disk are collapsed into part
stats show code paths.
* Rename disk_stat_lock/unlock() to part_stat_lock/unlock()
While at it, reposition stat handling macros a bit and add missing
parentheses around macro parameters.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Till now, bdev->bd_part is set only if the bdev was for parts other
than part0. This patch makes bdev->bd_part always set so that code
paths don't have to differenciate common handling.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement {disk|part}_to_dev() and use them to access generic device
instead of directly dereferencing {disk|part}->dev. To make sure no
user is left behind, rename generic devices fields to __dev.
This is in preparation of unifying partition 0 handling with other
partitions.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When two md arrays share some block device (e.g each uses different
partitions on the one device), a resync of one array will wait for
the resync on the other to finish.
This can be a long time and as it currently waits TASK_UNINTERRUPTIBLE,
the softlockup code notices and complains.
So use TASK_INTERRUPTIBLE instead and make sure to flush signals
before calling schedule.
Signed-off-by: NeilBrown <neilb@suse.de>
When stopping an md array, or just switching to read-only, we
currently call invalidate_partition while holding the mddev lock.
The main reason for this is probably to ensure all dirty buffers
are flushed (invalidate_partition calls fsync_bdev).
However if any dirty buffers are found, it will almost certainly cause
a deadlock as starting writeout will require an update to the
superblock, and performing that updates requires taking the mddev
lock - which is already held.
This deadlock can be demonstrated by running "reboot -f -n" with
a root filesystem on md/raid, and some dirty buffers in memory.
All other calls to stop an array should already happen after a flush.
The normal sequence is to stop using the array (e.g. umount) which
will cause __blkdev_put to call sync_blockdev. Then open the
array and issue the STOP_ARRAY ioctl while the buffers are all still
clean.
So this invalidate_partition is normally a no-op, except for one case
where it will cause a deadlock.
So remove it.
This patch possibly addresses the regression recored in
http://bugzilla.kernel.org/show_bug.cgi?id=11460
and
http://bugzilla.kernel.org/show_bug.cgi?id=11452
though it isn't yet clear how it ever worked.
Signed-off-by: NeilBrown <neilb@suse.de>
If a 'repair' is requested when an array is in a position to 'recover' raid1
will perform the repair while md believes a recovery is happening. Address
this at both ends, i.e. cancel check/repair requests upon detecting a
recover condition and do not call ->spare_active after completing a
check/repair.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Removing faulty devices from an array is a two stage process.
First the device is moved from being a part of the active array
to being similar to a spare device. Then it can be removed
by a request from user space.
The first step is currently not performed for read-only arrays,
so the second step can never succeed.
So allow readonly arrays to remove failed devices (which aren't
blocked).
Signed-off-by: NeilBrown <neilb@suse.de>
We cannot currently change the size of a write-intent bitmap.
So if we change the size of an array which has such a bitmap, it
tries to set bits beyond the end of the bitmap.
For now, simply reject any request to change the size of an array
which has a bitmap. mdadm can remove the bitmap and add a new one
after the array has changed size.
Signed-off-by: NeilBrown <neilb@suse.de>
A recent patch allowed do_md_stop to know whether it was being called
via an ioctl or not, and thus where to allow for an extra open file
descriptor when checking if it is in use.
This broke then switch to readonly performed by the shutdown notifier,
which needs to work even when the array is still (apparently) active
(as md doesn't get told when the filesystem becomes readonly).
So restore this feature by pretending that there can be lots of
file descriptors open, but we still want do_md_stop to switch to
readonly.
Signed-off-by: NeilBrown <neilb@suse.de>
If we reduce the 'safe_mode_delay', it could still wait for the old
delay to completely expire before doing anything about safe_mode.
Thus the effect if the change is delayed.
To make the effect more immediate, run the timeout function
immediately if the delay was reduced. This may cause it to run
slightly earlier that required, but that is the safer option.
Signed-off-by: NeilBrown <neilb@suse.de>
remove_and_add_spares() assumes that failed devices have been hot-removed
from the array. Removal is skipped in the 'blocked' case so do not count a
device in this state as 'spare'.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
All modifications and most access to the mddev->disks list are made
under the reconfig_mutex lock. However there are three places where
the list is walked without any locking. If a reconfig happens at this
time, havoc (and oops) can ensue.
So use RCU to protect these accesses:
- wrap them in rcu_read_{,un}lock()
- use list_for_each_entry_rcu
- add to the list with list_add_rcu
- delete from the list with list_del_rcu
- delay the 'free' with call_rcu rather than schedule_work
Note that export_rdev did a list_del_init on this list. In almost all
cases the entry was not in the list anymore so it was a no-op and so
safe. It is no longer safe as after list_del_rcu we may not touch
the list_head.
An audit shows that export_rdev is called:
- after unbind_rdev_from_array, in which case the delete has
already been done,
- after bind_rdev_to_array fails, in which case the delete isn't needed.
- before the device has been put on a list at all (e.g. in
add_new_disk where reading the superblock fails).
- and in autorun devices after a failure when the device is on a
different list.
So remove the list_del_init call from export_rdev, and add it back
immediately before the called to export_rdev for that last case.
Note also that ->same_set is sometimes used for lists other than
mddev->list (e.g. candidates). In these cases rcu is not needed.
Signed-off-by: NeilBrown <neilb@suse.de>
Open isn't the only thing that increments ->active. e.g. reading
/proc/mdstat will increment it briefly. So to avoid false positives
in testing for concurrent access, introduce a new counter that counts
just the number of times the md device it open.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the array_size field of struct mddev_s to array_sectors
and converts all instances to use units of 512 byte sectors instead of 1k
blocks.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Also, change the type of the size parameter from unsigned long long to
sector_t and rename it to num_sectors.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
The checks in overlaps() expect all parameters either in block-based
or sector-based quantities. However, its single caller passes two
rdev->data_offset arguments as well as two rdev->size arguments, the
former being sector counts while the latter are measured in 1K blocks.
This could cause rdev_size_store() to accept an invalid size from user
space. Fix it by passing only sector-based quantities to overlaps().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
- used strict_strtoull in place of simple_strtoull
- use my_mddev in place of rdev->mddev (they have the same value)
and more significantly,
- don't adjust mddev->size to fit, rather reject changes which make
rdev->size smaller than mddev->size
Adjusting mddev->size is a hangover from bind_rdev_to_array which
does a similar thing. But it really is a better design to insist that
mddev->size is set as required, then the rdev->sizes are set to allow
for that. The previous way invites confusion.
Signed-off-by: NeilBrown <neilb@suse.de>
Rename it to sb_start to make sure all users have been converted.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
As BLOCK_SIZE_BITS is 10 and
MD_NEW_SIZE_SECTORS(2 * x) = 2 * NEW_SIZE_BLOCKS(x),
the return value of calc_dev_sboffset() doubles. Fix up all three
callers accordingly.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Number of sectors is the preferred unit for sizes of raid devices,
so change calc_dev_size() so that it returns this unit instead of
the number of 1K blocks.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Changing the internal representations of sizes of raid devices
from 1K blocks to sector counts (512B units) is desirable because
it allows to get rid of many divisions/multiplications and unnecessary
casts that are present in the current code.
This patch is a first step in this direction. It replaces the old
1K-based "size" argument of update_size() by "num_sectors" and
fixes up its two callers.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
do_md_stop check the number of active users before allowing the array
to be stopped.
Two problems:
1/ it assumes the request is coming through an open file descriptor
(via ioctl) so it allows for that. This is not always the case.
2/ it doesn't do the check it the array hasn't been activated.
This is not good for cases when we use an inactive array to hold
some devices in a container.
Signed-off-by: Neil Brown <neilb@suse.de>
The current code copies a signed int from user space, converts it to
unsigned and passes the unsigned value to find_rdev_nr() which expects
a signed value. Simply pass the signed value from user space directly.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
If alloc_page() fails, ENOMEM is a more suitable error value
than EINVAL.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
The only caller of sb_equal() tests the return value against
zero, so it's OK to return the negated return value of memcmp().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
- Remove superfluous parentheses.
- Make format string match the type of the variable that is printed.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
In case pers->run() succeeds but creating the bitmap fails, we
print an error message stating that pers->run() has failed.
Print this message only if pers->run() really failed.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
md_allow_write() marks the metadata dirty while holding mddev->lock and then
waits for the write to complete. For externally managed metadata this causes a
deadlock as userspace needs to take the lock to communicate that the metadata
update has completed.
Change md_allow_write() in the 'external' case to start the 'mark active'
operation and then return -EAGAIN. The expected side effects while waiting for
userspace to write 'active' to 'array_state' are holding off reshape (code
currently handles -ENOMEM), cause some 'stripe_cache_size' change requests to
fail, cause some GET_BITMAP_FILE ioctl requests to fall back to GFP_NOIO, and
cause updates to 'raid_disks' to fail. Except for 'stripe_cache_size' changes
these failures can be mitigated by coordinating with mdmon.
md_write_start() still prevents writes from occurring until the metadata
handler has had a chance to take action as it unconditionally waits for
MD_CHANGE_CLEAN to be cleared.
[neilb@suse.de: return -EAGAIN, try GFP_NOIO]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
From: Chris Webb <chris@arachsys.com>
Allow /sys/block/mdX/md/rdY/size to change on running arrays, moving the
superblock if necessary for this metadata version. We prevent the available
space from shrinking to less than the used size, and allow it to be set to zero
to fill all the available space on the underlying device.
Signed-off-by: Chris Webb <chris@arachsys.com>
Signed-off-by: Neil Brown <neilb@suse.de>
The important state change happens during an interrupt
in md_error. So just set a flag there and call sysfs_notify
later in process context.
Signed-off-by: Neil Brown <neilb@suse.de>
When a device fails, when a spare is activated, when
an array is reshaped, or when an array is started,
the extent to which the array is degraded can change.
Signed-off-by: Neil Brown <neilb@suse.de>
When the 'resync' thread starts or stops, when we explicitly
set sync_action, or when we determine that there is definitely nothing
to do, we notify sync_action.
To stop "sync_action" from occasionally showing the wrong value,
we introduce a new flags - MD_RECOVERY_RECOVER - to say that a
recovery is probably needed or happening, and we make sure
that we set MD_RECOVERY_RUNNING before clearing MD_RECOVERY_NEEDED.
Signed-off-by: Neil Brown <neilb@suse.de>
Changes in md/array_state could be of interest to a monitoring
program. So make sure all changes trigger a notification.
Exceptions:
changing active_idle to active is not reported because it
is frequent and not interesting.
changing active to active_idle is only reported on arrays
with externally managed metadata, as it is not interesting
otherwise.
Signed-off-by: Neil Brown <neilb@suse.de>
There is really no need for this test here, and there are valid
cases for selectively removing devices from an array that
it not actually active.
Signed-off-by: Neil Brown <neilb@suse.de>
For all array types but linear, ->hot_add_disk returns 1 on
success, 0 on failure.
For linear, it returns 0 on success and -errno on failure.
This doesn't cause a functional problem because the ->hot_add_disk
function of linear is used quite differently to the others.
However it is confusing.
So convert all to return 0 for success or -errno on failure
and fix call sites to match.
Signed-off-by: Neil Brown <neilb@suse.de>
i.e. extend the 'md/dev-XXX/slot' attribute so that you can
tell a device to fill an vacant slot in an and md array.
Signed-off-by: Neil Brown <neilb@suse.de>
offset_store and rdev_size_store allow control of the region of a
device which is to be using in an md/raid array.
They only allow these values to be set when an array is being assembled,
as changing them on an active array could be dangerous.
However when adding a spare device to an array, we might need to
set the offset and size before starting recovery. So allow
these values to be set also if "->raid_disk < 0" which indicates that
the device is still a spare.
Signed-off-by: Neil Brown <neilb@suse.de>
Arrays personalities such as 'raid0' and 'linear' have no redundancy,
and so marking them as 'clean' or 'dirty' is not meaningful.
So always allow write requests without requiring a superblock update.
Such arrays types are detected by ->sync_request being NULL. If it is
not possible to send a sync request we don't need a 'dirty' flag because
all a dirty flag does is trigger some sync_requests.
Signed-off-by: Neil Brown <neilb@suse.de>
There is a possible race in md_probe. If two threads call md_probe
for the same device, then one could exit (having checked that
->gendisk exists) before the other has called kobject_init_and_add,
thus returning an incomplete kobj which will cause problems when
we try to add children to it.
So extend the range of protection of disks_mutex slightly to
avoid this possibility.
Signed-off-by: Neil Brown <neilb@suse.de>
This makes it possible to just resync a small part of an array.
e.g. if a drive reports that it has questionable sectors,
a 'repair' of just the region covering those sectors will
cause them to be read and, if there is an error, re-written
with correct data.
Signed-off-by: Neil Brown <neilb@suse.de>
md_probe can fail (e.g. alloc_disk could fail) without
returning an error (as it alway returns NULL).
So when we call mddev_find immediately afterwards, we need
to check that md_probe actually succeeded. This means checking
that mdev->gendisk is non-NULL.
cc: <stable@kernel.org>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Neil Brown <neilb@suse.de>
If an array was created with --assume-clean we will oops when trying to
set ->resync_max.
Fix this by initializing ->recovery_wait in mddev_find.
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we get any IO error during a recovery (rebuilding a spare), we abort
the recovery and restart it.
For RAID6 (and multi-drive RAID1) it may not be best to restart at the
beginning: when multiple failures can be tolerated, the recovery may be
able to continue and re-doing all that has already been done doesn't make
sense.
We already have the infrastructure to record where a recovery is up to
and restart from there, but it is not being used properly.
This is because:
- We sometimes abort with MD_RECOVERY_ERR rather than just MD_RECOVERY_INTR,
which causes the recovery not be be checkpointed.
- We remove spares and then re-added them which loses important state
information.
The distinction between MD_RECOVERY_ERR and MD_RECOVERY_INTR really isn't
needed. If there is an error, the relevant drive will be marked as
Faulty, and that is enough to ensure correct handling of the error. So we
first remove MD_RECOVERY_ERR, changing some of the uses of it to
MD_RECOVERY_INTR.
Then we cause the attempt to remove a non-faulty device from an array to
fail (unless recovery is impossible as the array is too degraded). Then
when remove_and_add_spares attempts to remove the devices on which
recovery can continue, it will fail, they will remain in place, and
recovery will continue on them as desired.
Issue: If we are halfway through rebuilding a spare and another drive
fails, and a new spare is immediately available, do we want to:
1/ complete the current rebuild, then go back and rebuild the new spare or
2/ restart the rebuild from the start and rebuild both devices in
parallel.
Both options can be argued for. The code currently takes option 2 as
a/ this requires least code change
b/ this results in a minimally-degraded array in minimal time.
Cc: "Eivind Sarto" <ivan@kasenna.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some configurations, a raid6 resync can be limited by CPU speed
(Calculating P and Q and moving data) rather than by device speed. In
these cases there is nothing to be gained byt serialising resync of arrays
that share a device, and doing the resync in parallel can provide benefit.
So add a sysfs tunable to flag an array as being allowed to resync in
parallel with other arrays that use (a different part of) the same device.
Signed-off-by: Bernd Schubert <bs@q-leap.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
