There are a few places around the code that invert inverted and possibly
inverted CD line. That's really confusing. Squash them all into one place
in mmc_gpiod_request_cd(). MMC_CAP2_CD_ACTIVE_HIGH is used analogously to
WP line: in GPIO mode it is used only at probe time to switch polarity, for
native mode it is left as is.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/db189b715596d63caf8c6a088bddc71dd69a879b.1576031637.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use MMC_CAP2_RO_ACTIVE_HIGH flag as indicator if GPIO line is to be
inverted compared to DT/platform-specified polarity. The flag is not used
after init in GPIO mode anyway. No functional changes intended.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/a60f563f11bbff821da2fa2949ca82922b144860.1576031637.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add possibility to toggle active-low flag of a gpio descriptor. This is
useful for compatibility code, where defaults are inverted vs DT gpio
flags or the active-low flag is taken from elsewhere.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/7ce0338e01ad17fa5a227176813941b41a7c35c1.1576031637.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A relatively large set of fixes here, the biggest part of it is for
fallout from the GPIO descriptor rework that affected several of the
devices with usable native chip select support. There's also some new
PCI IDs for Intel Jasper Lake devices.
The conversion to platform_get_irq() in the fsl driver is an incremental
fix for build errors introduced on SPARC by the earlier fix for error
handling in probe in that driver.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl34xt8THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0D64B/91GGhGgNybvExhls79YKQx9STnv8Vl
sIVgbnVxnTHrAa+s/5ML0T8LzH9W5KcBUuL+KCd0oMdaE9QZSCKGdraEqDJz7Ie4
iHbBSAtwL0tegbyM+J4oKC3wen3Lg1u1iwn4Plo2fVKEah7zG6gdneQcf454EnEF
om2Sj2K7tqoqN1jIl0j/FGQtlDXvhzp3m+CyGakjzsBvINmSGixrO5Lit/dx3qSf
xkhLDWZqUk3UatusPXhpJJVxWPuVvT5NQkvUYDte1rHxrVdolYQctwBRPN/uZ2hq
FcLzUbWVFx7p3cDqvuQ6XTptpue4njnaPOT/LW6tud4BexlaV1q83XYs
=gPXn
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A relatively large set of fixes here, the biggest part of it is for
fallout from the GPIO descriptor rework that affected several of the
devices with usable native chip select support. There's also some new
PCI IDs for Intel Jasper Lake devices.
The conversion to platform_get_irq() in the fsl driver is an
incremental fix for build errors introduced on SPARC by the earlier
fix for error handling in probe in that driver"
* tag 'spi-fix-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: fsl: use platform_get_irq() instead of of_irq_to_resource()
spi: nxp-fspi: Ensure width is respected in spi-mem operations
spi: spi-ti-qspi: Fix a bug when accessing non default CS
spi: fsl: don't map irq during probe
spi: spi-cavium-thunderx: Add missing pci_release_regions()
spi: sprd: Fix the incorrect SPI register
gpiolib: of: Make of_gpio_spi_cs_get_count static
spi: fsl: Handle the single hardwired chipselect case
gpio: Handle counting of Freescale chipselects
spi: fsl: Fix GPIO descriptor support
spi: dw: Correct handling of native chipselect
spi: cadence: Correct handling of native chipselect
spi: pxa2xx: Add support for Intel Jasper Lake
The driver is compatible with both Tegra186 and Tegra194, but currently
it cannot be selected if only Tegra194 support is enabled. Allow builds
with only Tegra194 support enabled to select this driver.
While at it, select this driver by default on Tegra194 builds because it
is an essential part of the system.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191213130034.219227-1-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move Lynxpoint GPIO driver under Intel pin control umbrella
for further transformation to a real pin control driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
- fix gpio-xtensa build failure
- fix a regression in gpio-mockup
- fix a gcc warning in gpio-aspeed
- fix a section mismatch problem in xgs-iproc
- fix a problem with emulated open-drain outputs in gpiolib core
- switch to bitops in gpio-pca953x after converting the driver to
using bitmap
- add a missed file to MAINTAINERS entry
-----BEGIN PGP SIGNATURE-----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=dqqa
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.5-rc2-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into fixes
gpio fixes for v5.5-rc2
- fix gpio-xtensa build failure
- fix a regression in gpio-mockup
- fix a gcc warning in gpio-aspeed
- fix a section mismatch problem in xgs-iproc
- fix a problem with emulated open-drain outputs in gpiolib core
- switch to bitops in gpio-pca953x after converting the driver to
using bitmap
- add a missed file to MAINTAINERS entry
We have for some time the assign_bit() API to replace open coded
if (foo)
set_bit(n, bar);
else
clear_bit(n, bar);
Use this API in GPIO library code.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191204194229.64251-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The LogiCVC display hardware block comes with GPIO capabilities
that must be exposed separately from the main driver (as GPIOs) for
use with regulators and panels. A syscon is used to share the same
regmap across the two drivers.
Add a minimalistic GPIO driver to drive these GPIOs, using a syscon
regmap when available.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://lore.kernel.org/r/20191203141243.251058-5-paul.kocialkowski@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove MODULE_VERSION(), as it isn't needed at all: the only version
making sense is the kernel version.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The string literal "gpiochip" is used in several places.
Add a definition for it, and use it everywhere, to make sure everything
stays in sync.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191127084253.16356-2-geert+renesas@glider.be
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_irq_count() is the more generic way (independent of
device trees) to determine the count of available interrupts. So
use this instead.
As platform_irq_count() might return an error code (which
of_irq_count doesn't) some additional handling is necessary.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
platform_irq_count() is the more generic way (independent of
device trees) to determine the count of available interrupts. So
use this instead.
As platform_irq_count() might return an error code (which
of_irq_count doesn't) some additional handling is necessary.
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There is no need to have a forward declaration for pca953x_dt_ids[].
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Since we have driver converted to use bitmap API we must use
traditional bit operations (set_bit(), clear_bit(), etc.)
against it.
Currently IRQ callbacks are missed in the conversion and
thus broken.
Let's fix it right here right now.
Fixes: 35d13d9489 ("gpio: pca953x: convert to use bitmap API")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Don't hardcode irq trigger to IRQF_TRIGGER_LOW while registering IRQ
handler. IRQ/platform core will take care of setting appropriate trigger
type.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
gpiolib has a corner case with open drain outputs that are emulated.
When such outputs are outputting a logic 1, emulation will set the
hardware to input mode, which will cause gpiod_get_direction() to
report that it is in input mode. This is different from the behaviour
with a true open-drain output.
Unify the semantics here.
Cc: <stable@vger.kernel.org>
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When built into the kernel, the driver causes a link problem:
`iproc_gpio_remove' referenced in section `.data' of drivers/gpio/gpio-xgs-iproc.o: defined in discarded section `.exit.text' of drivers/gpio/gpio-xgs-iproc.o
Remove the incorrect annotation.
Fixes: 6a41b6c5fc ("gpio: Add xgs-iproc driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
gcc has a hard time tracking whether BUG_ON(1) ends
execution or not:
drivers/gpio/gpio-aspeed-sgpio.c: In function 'bank_reg':
drivers/gpio/gpio-aspeed-sgpio.c:112:1: error: control reaches end of non-void function [-Werror=return-type]
Use the simpler BUG() that gcc knows cannot continue.
Fixes: f8b410e369 ("gpio: aspeed-sgpio: Rename and add Kconfig/Makefile")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Restore the external behavior of gpio-mockup to what it was prior to the
change to using GPIO_LINE_DIRECTION.
Fixes: e42615ec23 ("gpio: Use new GPIO_LINE_DIRECTION")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When a GPIO offset in a lookup table is out-of-range, the printed error
message (1) does not include the actual out-of-range value, and (2)
contains an off-by-one error in the upper bound.
Avoid user confusion by also printing the actual GPIO offset, and
correcting the upper bound of the range.
While at it, use "%u" for unsigned int.
Sample impact:
-requested GPIO 0 is out of range [0..32] for chip e6052000.gpio
+requested GPIO 0 (45) is out of range [0..31] for chip e6052000.gpio
Fixes: 2a3cf6a359 ("gpiolib: return -ENOENT if no GPIO mapping exists")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191127095919.4214-1-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit cad6fade6e ("xtensa: clean up WSR*/RSR*/get_sr/set_sr") removed
{RSR,WSR}_CPENABLE from xtensa code, but did not fix up all users,
breaking gpio-xtensa driver build. Update gpio-xtensa to use
new xtensa_{get,set}_sr API.
Cc: stable@vger.kernel.org # v5.0+
Fixes: cad6fade6e ("xtensa: clean up WSR*/RSR*/get_sr/set_sr")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There is no need to split some of the lines. However, improve the style
of multi-line comment. On top of this there is no need to have double
space.
Correct above indentation issues without altering the functionality.
Link: http://lkml.kernel.org/r/20191022172922.61232-12-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While PCA_PCAL is defined for PCA953X type only, we still may use an
offset of the input from regs structure for sake of consistency.
Link: http://lkml.kernel.org/r/20191022172922.61232-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We always will have at least one iteration of the loop due to pending
being guaranteed to be non-zero. That is, we may remove extra variable
and check in the IRQ handler.
Link: http://lkml.kernel.org/r/20191022172922.61232-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace verbose implementation in set_multiple callback with
for_each_set_clump8 macro to simplify code and improve clarity. An
improvement in this case is that banks that are not masked will now be
skipped.
Link: http://lkml.kernel.org/r/5b24887e97f3093e4832d7c50a1093f537e91ab4.1570641097.git.vilhelm.gray@gmail.com
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Morten Hein Tiljeset <morten.tiljeset@prevas.dk>
Cc: Phil Reid <preid@electromag.com.au>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix sparse warning:
drivers/gpio/gpiolib-of.c:35:5: warning:
symbol 'of_gpio_spi_cs_get_count' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191130012828.14504-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Core changes:
- Expose pull up/down flags for the GPIO character device to
userspace. After clear input from the RaspberryPi and Beagle
communities, it has been established that prototyping,
industrial automation and make communities strongly need
this feature, and as we want people to use the character
device, we have implemented the simple pull up/down
interface for GPIO lines. This means we can specify that
a (chip-specific) pull up/down resistor can be enabled,
but does not offer fine-grained control such as cases
where the resistance of the same pull resistor can be
controlled (yet).
- Introduce devm_fwnode_gpiod_get_index() and start to phase out
the old symbol devm_fwnode_get_index_gpiod_from_child().
- A bit of documentation clean-up work.
- Introduce a define for GPIO line directions and deploy it
in all GPIO drivers in the drivers/gpio directory.
- Add a special callback to populate pin ranges when
cooperating with the pin control subsystem and registering
ranges as part of adding a gpiolib driver and a
gpio_irq_chip driver at the same time. This is also
deployed in the Intel Merrifield driver.
New drivers:
- RDA Micro GPIO controller.
- XGS-iproc GPIO driver.
Driver improvements:
- Wake event and debounce support on the Tegra 186 driver.
- Finalize the Aspeed SGPIO driver.
- MPC8xxx uses a normal IRQ handler rather than a chained
handler.
-----BEGIN PGP SIGNATURE-----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=o13I
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.5 kernel cycle
Core changes:
- Expose pull up/down flags for the GPIO character device to
userspace.
After clear input from the RaspberryPi and Beagle communities, it
has been established that prototyping, industrial automation and
make communities strongly need this feature, and as we want people
to use the character device, we have implemented the simple pull
up/down interface for GPIO lines.
This means we can specify that a (chip-specific) pull up/down
resistor can be enabled, but does not offer fine-grained control
such as cases where the resistance of the same pull resistor can be
controlled (yet).
- Introduce devm_fwnode_gpiod_get_index() and start to phase out the
old symbol devm_fwnode_get_index_gpiod_from_child().
- A bit of documentation clean-up work.
- Introduce a define for GPIO line directions and deploy it in all
GPIO drivers in the drivers/gpio directory.
- Add a special callback to populate pin ranges when cooperating with
the pin control subsystem and registering ranges as part of adding
a gpiolib driver and a gpio_irq_chip driver at the same time. This
is also deployed in the Intel Merrifield driver.
New drivers:
- RDA Micro GPIO controller.
- XGS-iproc GPIO driver.
Driver improvements:
- Wake event and debounce support on the Tegra 186 driver.
- Finalize the Aspeed SGPIO driver.
- MPC8xxx uses a normal IRQ handler rather than a chained handler"
* tag 'gpio-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (64 commits)
gpio: Add TODO item for regmap helper
Documentation: gpio: driver.rst: Fix warnings
gpio: of: Fix bogus reference to gpiod_get_count()
gpiolib: Grammar s/manager/managed/
gpio: lynxpoint: Setup correct IRQ handlers
MAINTAINERS: Replace my email by one @kernel.org
gpiolib: acpi: Make acpi_gpiochip_alloc_event always return AE_OK
gpio/mpc8xxx: fix qoriq GPIO reading
gpio: mpc8xxx: Don't overwrite default irq_set_type callback
gpiolib: acpi: Print pin number on acpi_gpiochip_alloc_event errors
gpiolib: fix coding style in gpiod_hog()
drm/bridge: ti-tfp410: switch to using fwnode_gpiod_get_index()
gpio: merrifield: Pass irqchip when adding gpiochip
gpio: merrifield: Add GPIO <-> pin mapping ranges via callback
gpiolib: Introduce ->add_pin_ranges() callback
gpio: mmio: remove untrue leftover comment
gpio: em: Use platform_get_irq() to obtain interrupts
gpio: tegra186: Add debounce support
gpio: tegra186: Program interrupt route mapping
gpio: tegra186: Derive register offsets from bank/port
...
We have a special quirk to handle the Freescale
nonstandard SPI chipselect GPIOs in the gpiolib-of.c
file, but it currently only handles the case where
the GPIOs are actually requested (gpiod_*get()).
We also need to handle that the SPI core attempts
to count the GPIOs before use, and that needs a
similar quirk in the OF part of the library.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20191128083718.39177-2-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of the
patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs apis
so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over time,
it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules and
have it "just work" for a variety of platforms (like a distro kernel)
The big problem turned out to be a lack of depandancy information
between different areas of DT entries, and the work here resolves that
problem and now allows devices to boot properly, and quicker than a
monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6m6Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yntJQCcCqg6RQ7LTdHuZv1ETeefXlsfk00An1Jtean6
42bWGx52bGFvAcpjWy8R
=P7hq
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of
the patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs
apis so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over
time, it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules
and have it "just work" for a variety of platforms (like a distro
kernel). The big problem turned out to be a lack of dependency
information between different areas of DT entries, and the work here
resolves that problem and now allows devices to boot properly, and
quicker than a monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues"
* tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (68 commits)
tracing: Remove unnecessary DEBUG_FS dependency
of: property: Add device link support for interrupt-parent, dmas and -gpio(s)
debugfs: Fix !DEBUG_FS debugfs_create_automount
of: property: Add device link support for "iommu-map"
of: property: Fix the semantics of of_is_ancestor_of()
i2c: of: Populate fwnode in of_i2c_get_board_info()
drivers: base: Fix Kconfig indentation
firmware_loader: Fix labels with comma for builtin firmware
driver core: Allow device link operations inside sync_state()
driver core: platform: Declare ret variable only once
cpu-topology: declare parse_acpi_topology in <linux/arch_topology.h>
crypto: hisilicon: no need to check return value of debugfs_create functions
driver core: platform: use the correct callback type for bus_find_device
firmware_class: make firmware caching configurable
driver core: Clarify documentation for fwnode_operations.add_links()
mailbox: tegra: Fix superfluous IRQ error message
net: caif: Fix debugfs on 64-bit platforms
mac80211: Use debugfs_create_xul() helper
media: c8sectpfe: no need to check return value of debugfs_create functions
of: property: Add device link support for iommus, mboxes and io-channels
...
Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6ewA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymNXACfebVkDrFOH9EqDgFArPvZ1i9EmZ4AoLbE1Wki
ftJApk+Ov1BT2TvClOza
=cXqg
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (198 commits)
char: Fix Kconfig indentation, continued
habanalabs: add more protection of device during reset
habanalabs: flush EQ workers in hard reset
habanalabs: make the reset code more consistent
habanalabs: expose reset counters via existing INFO IOCTL
habanalabs: make code more concise
habanalabs: use defines for F/W files
habanalabs: remove prints on successful device initialization
habanalabs: remove unnecessary checks
habanalabs: invalidate MMU cache only once
habanalabs: skip VA block list update in reset flow
habanalabs: optimize MMU unmap
habanalabs: prevent read/write from/to the device during hard reset
habanalabs: split MMU properties to PCI/DRAM
habanalabs: re-factor MMU masks and documentation
habanalabs: type specific MMU cache invalidation
habanalabs: re-factor memory module code
habanalabs: export uapi defines to user-space
habanalabs: don't print error when queues are full
habanalabs: increase max jobs number to 512
...
Another fairly quiet release for the regulator API, some work all around
including some core work but mostly in specialist or driver specific
code:
- Fix for powering off boot-on regulators.
- Enhancements to the coupled regulator support introduced in the last
release.
- Conversion of a bunch of drivers to the fwnode API for GPIOs.
- Mode support for DA9062.
- New device support for Qualcomm PM1650, PM8004 and PM895 and Silergy
SR83X.
- Removal of obsolete AB8505 support.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl3b04ETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0B82B/9Eto3rSo03EqkkKG3clSKPDGO9WSZG
LSLQ0lbHxsXL8cyIoOx8S/ygiyLn07SLFbLFVhkMi/JXNlPxlNMKMohY3yNffKMd
7DQgWiqeFDEyxU9bFoTR1mAWMfycNUCGFDWel2EjmnhJ0NA5hyjXzXwgoYIUWMPf
GQBMp6Qbxtl9SShNeuMNlzFdHdThAr8JNm014UVQLeg0Kx1DowMDWgCYVuHmRqDB
6VF37pNxaqPcGB/nqxJfSJULrj6brLJuQ9KFNGROxP9VPK8lt0+Aaeg3HsLq/LLe
z6q0bAJ9EVJYhAuJYrSpUgDdd5pxcshLj3rzl70kH0Ac+GWjQsqfoqTO
=jJ5N
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Another fairly quiet release for the regulator API, some work all
around including some core work but mostly in specialist or driver
specific code:
- Fix for powering off boot-on regulators
- Enhancements to the coupled regulator support introduced in the
last release
- Conversion of a bunch of drivers to the fwnode API for GPIOs
- Mode support for DA9062
- New device support for Qualcomm PM1650, PM8004 and PM895 and
Silergy SR83X
- Removal of obsolete AB8505 support"
* tag 'regulator-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (49 commits)
regulator: da9062: Return REGULATOR_MODE_INVALID for invalid mode
regulator: Fix Kconfig indentation
regulator: tps6105x: add optional devicetree support
tps6105x: add optional devicetree support
regulator: rn5t618: fix rc5t619 ldo10 enable
regulator: vexpress: Use PTR_ERR_OR_ZERO() to simplify code
dt-bindings: mfd: da9062: describe buck modes
regulator: da9062: add of_map_mode support for bucks
regulator: da9062: refactor buck modes into header
regulator: stpmic1: Set a default ramp delay value
regulator: core: Let boot-on regulators be powered off
regulator: core: Don't try to remove device links if add failed
regulator: ab8500: Remove SYSCLKREQ from enum ab8505_regulator_id
regulator: ab8500: Remove AB8505 USB regulator
regulator: fan53555: add chip id for Silergy SYR83X
regulator: fixed: add off-on-delay
dt-bindings: regulator: fixed: add off-on-delay-us property
regulator: core: Allow generic coupling only for always-on regulators
regulator: core: Release coupled_rdevs on regulator_init_coupling() error
regulator: bd70528: Add MODULE_ALIAS to allow module auto loading
...
- Atomics-related code sees some rework & cleanup, most notably allowing
Loongson LL/SC errata workarounds to be more bulletproof & their
correctness to be checked at build time.
- Command line setup code is simplified somewhat, resolving various
corner cases.
- MIPS kernels can now be built with kcov code coverage support.
- We can now build with CONFIG_FORTIFY_SOURCE=y.
- Miscellaneous cleanups.
And some platform specific changes:
- We now disable some broken TLB functionality on certain Ingenic
systems, and JZ4780 systems gain some devicetree nodes to support
more devices.
- Loongson support sees a number of cleanups, and we gain initial
support for Loongson 3A R4 systems.
- We gain support for MediaTek MT7688-based GARDENA Smart Gateway
systems.
- SGI IP27 (Origin 2*) see a number of fixes, cleanups &
simplifications.
- SGI IP30 (Octane) systems are now supported.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXdwj2RYccGF1bGJ1cnRv
bkBrZXJuZWwub3JnAAoJED6nn6y1dQDd54QA/2CrWLcWCcWVwN8XwLTh3gWf8/k7
d19Ttd0bYrsBUnaHAP9s9kc9RFOAhB3p1G0dsMZqI0YX7emLGPgW3ejJ7CXNCg==
=/Hsa
-----END PGP SIGNATURE-----
Merge tag 'mips_5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"The main MIPS changes for 5.5:
- Atomics-related code sees some rework & cleanup, most notably
allowing Loongson LL/SC errata workarounds to be more bulletproof &
their correctness to be checked at build time.
- Command line setup code is simplified somewhat, resolving various
corner cases.
- MIPS kernels can now be built with kcov code coverage support.
- We can now build with CONFIG_FORTIFY_SOURCE=y.
- Miscellaneous cleanups.
And some platform specific changes:
- We now disable some broken TLB functionality on certain Ingenic
systems, and JZ4780 systems gain some devicetree nodes to support
more devices.
- Loongson support sees a number of cleanups, and we gain initial
support for Loongson 3A R4 systems.
- We gain support for MediaTek MT7688-based GARDENA Smart Gateway
systems.
- SGI IP27 (Origin 2*) see a number of fixes, cleanups &
simplifications.
- SGI IP30 (Octane) systems are now supported"
* tag 'mips_5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (107 commits)
MIPS: SGI-IP27: Enable ethernet phy on second Origin 200 module
MIPS: PCI: Fix fake subdevice ID for IOC3
MIPS: Ingenic: Disable abandoned HPTLB function.
MIPS: PCI: remember nasid changed by set interrupt affinity
MIPS: SGI-IP27: Fix crash, when CPUs are disabled via nr_cpus parameter
mips: add support for folded p4d page tables
mips: drop __pXd_offset() macros that duplicate pXd_index() ones
mips: fix build when "48 bits virtual memory" is enabled
MIPS: math-emu: Reuse name array in debugfs_fpuemu()
MIPS: allow building with kcov coverage
MIPS: Loongson64: Drop setup_pcimap
MIPS: Loongson2ef: Convert to early_printk_8250
MIPS: Drop CPU_SUPPORTS_UNCACHED_ACCELERATED
MIPS: Loongson{2ef, 32, 64} convert to generic fw cmdline
MIPS: Drop pmon.h
MIPS: Loongson: Unify LOONGSON3/LOONGSON64 Kconfig usage
MIPS: Loongson: Rename LOONGSON1 to LOONGSON32
MIPS: Loongson: Fix return value of loongson_hwmon_init
MIPS: add support for SGI Octane (IP30)
MIPS: PCI: make phys_to_dma/dma_to_phys for pci-xtalk-bridge common
...
When commit 75e99bf5ed ("gpio: lynxpoint: set default handler to be
handle_bad_irq()") switched default handler to be handle_bad_irq() the
lp_irq_type() function remained untouched. It means that even request_irq()
can't change the handler and we are not able to handle IRQs properly anymore.
Fix it by setting correct handlers in the lp_irq_type() callback.
Fixes: 75e99bf5ed ("gpio: lynxpoint: set default handler to be handle_bad_irq()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191118180251.31439-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
acpi_gpiochip_alloc_event is used to loop over all _AEI resources, if
we fail to bind an event handler to one of them, that is not a reason to
not try the other resources.
This commit modifies acpi_gpiochip_alloc_event to always return AE_OK,
so that we will always try to add an event handler for all _AEI resources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20191114102600.34558-2-hdegoede@redhat.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Qoriq requires the IBE register to be set to enable GPIO inputs to be
read. Set it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1iX3HC-00069N-0T@rmk-PC.armlinux.org.uk
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The per-SoC devtype structures can contain their own callbacks that
overwrite mpc8xxx_gpio_devtype_default.
The clear intention is that mpc8xxx_irq_set_type is used in case the SoC
does not specify a more specific callback. But what happens is that if
the SoC doesn't specify one, its .irq_set_type is de-facto NULL, and
this overwrites mpc8xxx_irq_set_type to a no-op. This means that the
following SoCs are affected:
- fsl,mpc8572-gpio
- fsl,ls1028a-gpio
- fsl,ls1088a-gpio
On these boards, the irq_set_type does exactly nothing, and the GPIO
controller keeps its GPICR register in the hardware-default state. On
the LS1028A, that is ACTIVE_BOTH, which means 2 interrupts are raised
even if the IRQ client requests LEVEL_HIGH. Another implication is that
the IRQs are not checked (e.g. level-triggered interrupts are not
rejected, although they are not supported).
Fixes: 82e39b0d85 ("gpio: mpc8xxx: handle differences between incarnations at a single place")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20191115125551.31061-1-olteanv@gmail.com
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Print pin number and error-code on acpi_gpiochip_alloc_event errors,
to help debugging these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20191114102600.34558-1-hdegoede@redhat.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There should be spaces between logical operators and their operands.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Prerequisite patch against GPIO library to register pin ranges in time.
* Second attempt to fix Intel Merrifield GPIO driver to utilize irqchip.
The following is an automated git shortlog grouped by driver:
gpiolib:
- Introduce ->add_pin_ranges() callback
merrifield:
- Pass irqchip when adding gpiochip
- Add GPIO <-> pin mapping ranges via callback
-----BEGIN PGP SIGNATURE-----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=BRPx
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel
intel-gpio for v5.5-1
* Prerequisite patch against GPIO library to register pin ranges in time.
* Second attempt to fix Intel Merrifield GPIO driver to utilize irqchip.
The following is an automated git shortlog grouped by driver:
gpiolib:
- Introduce ->add_pin_ranges() callback
merrifield:
- Pass irqchip when adding gpiochip
- Add GPIO <-> pin mapping ranges via callback
- add MODULE_ALIAS() for bd70528 (makes it possible to autoload the
module from user-space)
- use proper irc_chip names in gpio-em and gpio-rcar
- expose the line bias settings to user-space in the form of new request
flags
- expose a new ioctl() to user-space which allows to change certain
proprties of requested lines without releasing them first
- various updates for gpio-tegra186: debounce support, code
simplification and interrupt routing
- use platform_get_irq() in gpio-em for some code shrinkage
- remove leftovers after recent gpio-mmio changes
-----BEGIN PGP SIGNATURE-----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=qZW7
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.5-updates-for-linus-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio: updates for v5.5
- add MODULE_ALIAS() for bd70528 (makes it possible to autoload the
module from user-space)
- use proper irc_chip names in gpio-em and gpio-rcar
- expose the line bias settings to user-space in the form of new request
flags
- expose a new ioctl() to user-space which allows to change certain
proprties of requested lines without releasing them first
- various updates for gpio-tegra186: debounce support, code
simplification and interrupt routing
- use platform_get_irq() in gpio-em for some code shrinkage
- remove leftovers after recent gpio-mmio changes
- fix debounce times in max776520 and bd70528
- fix parallel build of gpio tools
-----BEGIN PGP SIGNATURE-----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=R2RD
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.4-rc8-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into fixes
gpio fixes for v5.4-rc8
- fix debounce times in max776520 and bd70528
- fix parallel build of gpio tools
The Terra Pad 1061 has the usual micro-USB-B id-pin handler, but instead
of controlling the actual micro-USB-B it turns the 5V boost for the
tablet's USB-A connector and its keyboard-cover connector off.
The actual micro-USB-B connector on the tablet is wired for charging only,
and its id pin is *not* connected to the GPIO which is used for the
(broken) id-pin event handler in the DSDT.
While at it not only add a comment why the Terra Pad 1061 is on the
blacklist, but also fix the missing comment for the Minix Neo Z83-4 entry.
Fixes: 61f7f7c8f9 ("gpiolib: acpi: Add gpiolib_acpi_run_edge_events_on_boot option and blacklist")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward conversion.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
When IRQ chip is instantiated via GPIO library flow, the few functions,
in particular the ACPI event registration mechanism, on some of ACPI based
platforms expect that the pin ranges are initialized to that point.
Add GPIO <-> pin mapping ranges via callback in the GPIO library flow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When IRQ chip is being added by GPIO library, the ACPI based platform expects
GPIO <-> pin mapping ranges to be initialized in order to correctly initialize
ACPI event mechanism on affected platforms. Unfortunately this step is missed.
Introduce ->add_pin_ranges() callback to fill the above mentioned gap.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
The comment should have been removed when new GPIO direction
definitions were taken in use as the function logic was changed. It
is now perfectly valid and Ok to hit the return from the bottom of
the direction getting function.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The GPIO controller found on Tegra186 and later supports debouncing for
inputs for up to 255 ms.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The controls for the GG port on Tegra194 resides in the power partition
of the C5 PCIe controller and its interrupt route mapping can therefore
not be programmed by early boot firmware along with that of the other
ports.
Detect this generically by looking at which controls have already been
locked down using the security registers and fill in default values for
controls that are unlocked.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The register offsets for a given bank and port can be easily derived
from the bank and port indices. Update the port descriptors to list only
the bank and port numbers to simplify this.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add the GPIOHANDLE_SET_CONFIG_IOCTL to the gpio chardev.
The ioctl allows some of the configuration of a requested handle to be
changed without having to release the line.
The primary use case is the changing of direction for bi-directional
lines.
Based on initial work by Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Move validation of line handle flags into helper function.
This reduces the size and complexity of linehandle_create and allows the
validation to be reused elsewhere.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add support for the pull up/down state set via gpiolib line requests to
be reflected in the state of the mockup.
Use case is for testing of the GPIO uAPI, specifically the pull up/down
flags.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Allow pull up/down bias to be set on output lines.
Use case is for open source or open drain applications where
internal pull up/down may conflict with external biasing.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Allow pull up/down bias to be disabled, allowing the line to float
or to be biased only by external circuitry.
Use case is for where the bias has been applied previously, either
by default or by the user, but that setting may conflict with the
current use of the line.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add support for pull up/down to lineevent_create.
Use cases include receiving asynchronous presses from a
push button without an external pull up/down.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add pull-up/pull-down flags to the gpio line get and
set ioctl() calls. Use cases include a push button
that does not have an external resistor.
Addition use cases described by Limor Fried (ladyada) of
Adafruit in this PR for Adafruit_Blinka Python lib:
https://github.com/adafruit/Adafruit_Blinka/pull/59
Signed-off-by: Drew Fustini <drew@pdp7.com>
[Kent: added BIAS to GPIO flag names and restrict application to input
lines]
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The irq_chip .name field should contain the device's class name, not the
instance's name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The irq_chip .name field should contain the device's class name, not the
instance's name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The bd70528 GPIO driver is probed by MFD driver. Add MODULE_ALIAS
in order to allow udev to load the module when MFD sub-device cell
for GPIO is added.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The debounce time passed to gpiod_set_debounce() is specified in
microseconds, so make sure to use the correct unit when computing the
register values, which denote delays in milliseconds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Cc: <stable@vger.kernel.org>
Fixes: 18bc64b3ae ("gpio: Initial support for ROHM bd70528 GPIO block")
[Bartosz: fixed a typo in commit message]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When converting milliseconds to microseconds in commit fffa6af948
("gpio: max77620: Use correct unit for debounce times") some ~1 ms gaps
were introduced between the various ranges supported by the controller.
Fix this by changing the start of each range to the value immediately
following the end of the previous range. This way a debounce time of,
say 8250 us will translate into 16 ms instead of returning an -EINVAL
error.
Typically the debounce delay is only ever set through device tree and
specified in milliseconds, so we can never really hit this issue because
debounce times are always a multiple of 1000 us.
The only notable exception for this is drivers/mmc/host/mmc-spi.c where
the CD GPIO is requested, which passes a 1 us debounce time. According
to a comment preceeding that code this should actually be 1 ms (i.e.
1000 us).
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 8c550e94b8.
This was prematurely applied and we need to back it out to merge
a better version of the development track for this feature.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_gpiochip_add(), when fails, calls gpiochip_remove_pin_ranges().
ADD:
gpiochip_add_data_with_key() ->
of_gpiochip_add() -> (ERROR path)
gpiochip_remove_pin_ranges()
At the same time of_gpiochip_remove() calls exactly the above mentioned
function unconditionally and so does gpiochip_remove().
REMOVE:
gpiochip_remove() ->
gpiochip_remove_pin_ranges()
of_gpiochip_remove() ->
gpiochip_remove_pin_ranges()
Since gpiochip_remove() calls gpiochip_remove_pin_ranges() unconditionally,
we have duplicate call to the same function when it's not necessary.
Move gpiochip_remove_pin_ranges() from of_gpiochip_add() to gpiochip_add()
to avoid duplicate calls and be consistent with the explicit call in
gpiochip_remove().
Fixes: e93fa3f243 ("gpiolib: remove duplicate pin range code")
Depends-on: f7299d441a ("gpio: of: Fix of_gpiochip_add() error path")
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's hard for occasional GPIO code reader/writer to know if values 0/1
equal to IN or OUT. Use defined GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT to help them out.
NOTE - for gpio-amd-fch and gpio-bd9571mwv:
This commit also changes the return value for direction get to equal 1
for direction INPUT. Prior this commit these drivers might have
returned some other positive value but 1 for INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The table of devicetree identifiers is annotated as __initconst
indicating that it can be discarded after kernel boot but it is
referenced from the driver struct which has no init annotation leading
to a linker warning:
WARNING: vmlinux.o(.data+0x82d58): Section mismatch in reference from the variable bcm_iproc_gpio_driver to the variable .init.rodata:bcm_iproc_gpio_of_match
The variable bcm_iproc_gpio_driver references
the variable __initconst bcm_iproc_gpio_of_match
Since drivers can be probed after init the lack of annotation on the
driver struct is correct so remove the annotation from the match table.
Fixes: 6a41b6c5fc ("gpio: Add xgs-iproc driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO irqchip needs to initialize the valid mask
before initializing the IRQ hardware, because sometimes
the latter require the former to be executed first.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20191030122914.967-1-linus.walleij@linaro.org
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 8f86a5b4ad.
It has been established that this causes a boot regression on
both Baytrail and Cherrytrail SoCs, and we can't have that in
the final kernel release, so we need to revert it.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 6658f87f21.
This revert is a prerequisite for the later revert of commit
8f86a5b4ad.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 4c87540940.
This revert is a prerequisite for the later revert of commit
8f86a5b4ad.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have symbol namespaces, use them in MCB to not pollute the
default namespace with MCB internals.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jessica Yu <jeyu@kernel.org>
Reviewed-by: Michael Moese <mmoese@suse.de>
Link: https://lore.kernel.org/r/20191016100158.1400-1-jthumshirn@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix VDSO time-related function behavior for systems where we need to
fall back to syscalls, but were instead returning bogus results.
- A fix to TLB exception handlers for Cavium Octeon systems where they
would inadvertently clobber the $1/$at register.
- A build fix for bcm63xx configurations.
- Switch to using my @kernel.org email address.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXbTEbhYccGF1bGJ1cnRv
bkBrZXJuZWwub3JnAAoJED6nn6y1dQDd+HsBAJ2Zvzlm+CftfNTPbG1SihhyH3s4
edn8VuexsPJp+TjJAP9UZHPQj35tvS5MWYRg0YsNz9HYPTVclYdEsLS9KbSMCw==
=YNU+
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXbylbRYccGF1bGJ1cnRv
bkBrZXJuZWwub3JnAAoJED6nn6y1dQDd3JkA/2zyRKMikSbQjyr3E2XRnx0HwIUa
UjeQvSR0+wofAI0VAP9D3IzB0ugAsGawUSWeYHK5CXBoSrsFNasjxNBT/G1MDA==
=duXm
-----END PGP SIGNATURE-----
Merge tag 'mips_fixes_5.4_3' into mips-next
Pull in mips-fixes primarily to gain build fixes in order to allow
better testing of mips-next.
A few MIPS fixes:
- Fix VDSO time-related function behavior for systems where we need to
fall back to syscalls, but were instead returning bogus results.
- A fix to TLB exception handlers for Cavium Octeon systems where they
would inadvertently clobber the $1/$at register.
- A build fix for bcm63xx configurations.
- Switch to using my @kernel.org email address.
Signed-off-by: Paul Burton <paulburton@kernel.org>
CPU_LOONGSON2 -> CPU_LOONGSON2EF
CPU_LOONGSON3 -> CPU_LOONGSON64
As newer loongson-2 products (2G/2H/2K1000) can share kernel
implementation with loongson-3 while 2E/2F are less similar with
other LOONGSON64 products.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: chenhc@lemote.com
Cc: paul.burton@mips.com
This driver supports the Chip Common A GPIO controller present on a
number of Broadcom switch ASICs with integrated SoCs. The controller is
similar to the pinctrl-nsp-gpio and pinctrl-iproc-gpio blocks but
different enough that a separate driver is required.
This has been ported from Broadcom's XLDK 5.0.3 retaining only the CCA
support (pinctrl-iproc-gpio covers CCB).
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191024202703.8017-3-chris.packham@alliedtelesis.co.nz
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for GPIO controller from RDA Micro. This GPIO controller
is an in house IP, developed by RDA Micro (now Unisoc) for the use in
RDA88* series of SoCs. There are multiple GPIO ports present in all SoCs,
each capable of addressing 32 GPIOs. But only first 8 pins have the
interrupt capability.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20191021064413.19840-4-manivannan.sadhasivam@linaro.org
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- only get the second IRQ when there is more than one IRQ in mxc
- move the code around in lineevent_create() for some shrinkage
- fix formatting for GPIO docs
- add DT binding for r8a774b1
- convert drivers that prevously used nocache ioremap() to using regular
devm_platform_ioremap_resource()
- remove some redundant error messages
- shrink object code in 104-idi-48e
- drop an unneeded warning from gpiolib-of
-----BEGIN PGP SIGNATURE-----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=mQ1k
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.5-updates-for-linus-part-1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.5
- only get the second IRQ when there is more than one IRQ in mxc
- move the code around in lineevent_create() for some shrinkage
- fix formatting for GPIO docs
- add DT binding for r8a774b1
- convert drivers that prevously used nocache ioremap() to using regular
devm_platform_ioremap_resource()
- remove some redundant error messages
- shrink object code in 104-idi-48e
- drop an unneeded warning from gpiolib-of
Some devicetrees specify the ACTIVE_LOW flag in the fixed regulator GPIO
handle. While this has always been ignored, it's consistent with the
behavior of the regulator binding in the absence of the
"enable-active-high" DT property. It doesn't make much sense to print a
user visible warning for a configuration which is consistent, so only
print the warning if the GPIO flag contradicts the behavior dictated by
by the enable-active-high property.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[Bartosz: coding style tweak]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
More than one gpio controllers can share one interrupt, change the
driver to request shared irq.
While this will work, it will mess up userspace accounting of the number
of interrupts per second in tools such as vmstat. The reason is that
for every GPIO interrupt, /proc/interrupts records the count against GIC
interrupt 68 or 69, as well as the GPIO itself. So, for every GPIO
interrupt, the total number of interrupts that the system has seen
increments by two.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Link: https://lore.kernel.org/r/20191011005643.41007-1-hui.song_1@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We switch the default handler to be handle_bad_irq() instead of
handle_simple_irq() (which was not correct anyway).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver wants to initialize related registers before IRQ chip will be added.
That's why move it to a corresponding callback. It also fixes the NULL pointer
dereference.
Fixes: 8f86a5b4ad ("gpio: merrifield: Pass irqchip when adding gpiochip")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver wants to initialize related registers before IRQ chip will be added.
That's why move it to a corresponding callback. It also fixes the NULL pointer
dereference.
Fixes: 7b1e889436 ("gpio: lynxpoint: Pass irqchip when adding gpiochip")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver wants to initialize related registers before IRQ chip will be added.
That's why move it to a corresponding callback. It also fixes the NULL pointer
dereference.
Fixes: 8069e69a97 ("gpio: intel-mid: Pass irqchip when adding gpiochip")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After changing the drivers to use GPIO core to add an IRQ chip
it appears that some of them requires a hardware initialization
before adding the IRQ chip.
Add an optional callback ->init_hw() to allow that drivers
to initialize hardware if needed.
This change is a part of the fix NULL pointer dereference
brought to the several drivers recently.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During conversion to internal IRQ chip initialization the commit
8f86a5b4ad ("gpio: merrifield: Pass irqchip when adding gpiochip")
lost the irq_base assignment.
drivers/gpio/gpio-merrifield.c: In function ‘mrfld_gpio_probe’:
drivers/gpio/gpio-merrifield.c:405:17: warning: variable ‘irq_base’ set but not used [-Wunused-but-set-variable]
Assign the girq->first to it.
Fixes: 8f86a5b4ad ("gpio: merrifield: Pass irqchip when adding gpiochip")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Don't populate the array register_offset on the stack but instead make it
static. Makes the object code smaller by 63 bytes. Also add the int type
specifier to clean up a checkpatch warning.
Before:
text data bss dec hex filename
9212 5712 1408 16332 3fcc drivers/gpio/gpio-104-idi-48.o
After:
text data bss dec hex filename
9085 5776 1408 16269 3f8d drivers/gpio/gpio-104-idi-48.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There's no need to emit an error message on probe failure unless we're
printing some meaningful info. Otherwise the core driver code will
inform us about a probe error. Also: the driver currently drops info
about errors propagated from called functions by default to returning
-EINVAL. This fixes it as well.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There's no need to use the nocache variant of ioremap(). Switch to
using devm_platform_ioremap_resource().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There's no need to use the nocache variant of ioremap(). Switch to
using devm_platform_ioremap_resource().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There's no need to use the nocache variant of ioremap(). Switch to
using devm_platform_ioremap_resource().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
There's no need to use the nocache variant of ioremap(). Switch to
using devm_platform_ioremap_resource().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There's no need to emit an error message on probe failure unless we're
printing some meaningful info. Otherwise the core driver code will
inform us about a probe error.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add pull-up/pull-down flags to the gpio line get and
set ioctl() calls. Use cases include a push button
that does not have an external resistor.
Addition use cases described by Limor Fried (ladyada) of
Adafruit in this PR for Adafruit_Blinka Python lib:
https://github.com/adafruit/Adafruit_Blinka/pull/59
Signed-off-by: Drew Fustini <drew@pdp7.com>
Link: https://lore.kernel.org/r/20190921102522.8970-1-drew@pdp7.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO controller doesn't have any controls to enable the system to
wake up from low power states based on activity on GPIO pins. An extra
hardware block that is part of the power management controller (PMC)
contains these controls. In order for the GPIO controller to be able
to cooperate with the PMC, obtain a reference to the PMC's IRQ domain
and make it a parent to the GPIO controller's IRQ domain. This way the
PMC gets an opportunity to program the additional registers required
to enable wakeup sources on suspend.
Based on additional work by Bitan Biswas <bbiswas@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191002144502.156393-2-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt-related register fields on the MAX77620 GPIO controller
share registers with GPIO related fields. If the IRQ chip is implemented
with regmap-irq, this causes the IRQ controller code to overwrite fields
previously configured by the GPIO controller code.
Two examples where this causes problems are the NVIDIA Jetson TX1 and
Jetson TX2 boards, where some of the GPIOs are used to enable vital
power regulators. The MAX77620 GPIO controller also provides the USB OTG
ID pin. If configured as an interrupt, this causes some of the
regulators to be powered off.
Signed-off-by: Timo Alho <talho@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191002122825.3948322-3-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
regmap_add_irq_chip() will try to allocate all of the IRQ descriptors
upfront if passed a non-zero irq_base parameter. However, the intention
is to allocate IRQ descriptors on an as-needed basis if possible. Pass 0
instead of -1 to fix that use-case.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191002122825.3948322-2-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpiod_set_debounce() function takes the debounce time in
microseconds. Adjust the switch/case values in the MAX77620 GPIO to use
the correct unit.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191002122825.3948322-1-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This introduces fwnode_gpiod_get_index() that iterates through common gpio
suffixes when trying to locate a GPIO within a given firmware node.
We also switch devm_fwnode_gpiod_get_index() to call
fwnode_gpiod_get_index() instead of iterating through GPIO suffixes on
its own.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190913032240.50333-3-dmitry.torokhov@gmail.com
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_fwnode_get_index_gpiod_from_child() is too long, besides the fwnode
in question does not have to be a child of device node. Let's rename it
to devm_fwnode_gpiod_get_index() and keep the old name for compatibility
for now.
Also let's add a devm_fwnode_gpiod_get() wrapper as majority of the
callers need a single GPIO.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20190913032240.50333-2-dmitry.torokhov@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move all the flags sanitization before any memory allocation in
lineevent_create() in order to remove a couple unneeded gotos.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When toggling the level trigger to emulate the edge trigger, the
EIC offset is incorrect without adding the corresponding bank index,
thus fix it.
Fixes: 7bf0d7f622 ("gpio: eic: Add edge trigger emulation for EIC")
Cc: stable@vger.kernel.org
Signed-off-by: Bruce Chen <bruce.chen@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Since commit ec757001c8 ("gpio: Enable nonexclusive gpiods from DT
nodes") we are able to get GPIOD_FLAGS_BIT_NONEXCLUSIVE marked gpios.
Currently the gpiolib uses the wrong flags variable for the check. We
need to check the gpiod_flags instead of the of_gpio_flags else we
return -EBUSY for GPIOD_FLAGS_BIT_NONEXCLUSIVE marked and requested
gpiod's.
Fixes: ec757001c8 gpio: Enable nonexclusive gpiods from DT nodes
Cc: stable@vger.kernel.org
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[Bartosz: the function was moved to gpiolib-of.c so updated the patch]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When emulating open-drain/open-source by not actively driving the output
lines - we're simply changing their mode to input. This is wrong as it
will then make it impossible to change the value of such line - it's now
considered to actually be in input mode. If we want to still use the
direction_input() callback for simplicity then we need to set FLAG_IS_OUT
manually in gpiod_direction_output() and not clear it in
gpio_set_open_drain_value_commit() and
gpio_set_open_source_value_commit().
Fixes: c663e5f567 ("gpio: support native single-ended hardware drivers")
Cc: stable@vger.kernel.org
Reported-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
On some of i.MX SoCs like i.MX8QXP, there is ONLY one IRQ for each
GPIO bank, so it is better to check the IRQ count before getting
second IRQ to avoid below error message during probe:
[ 1.070908] gpio-mxc 5d080000.gpio: IRQ index 1 not found
[ 1.077420] gpio-mxc 5d090000.gpio: IRQ index 1 not found
[ 1.083766] gpio-mxc 5d0a0000.gpio: IRQ index 1 not found
[ 1.090122] gpio-mxc 5d0b0000.gpio: IRQ index 1 not found
[ 1.096470] gpio-mxc 5d0c0000.gpio: IRQ index 1 not found
[ 1.102804] gpio-mxc 5d0d0000.gpio: IRQ index 1 not found
[ 1.109144] gpio-mxc 5d0e0000.gpio: IRQ index 1 not found
[ 1.115475] gpio-mxc 5d0f0000.gpio: IRQ index 1 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This renames the "gpio-aspeed" driver to conform with other
GPIO drivers as "gpio-aspeed-sgpio.c". All GPIO drivers
should start with the string "gpio-" no special exceptions.
Also the Kconfig and Makefile entries should normally
go with the driver but I missed this in my review, sorry
for mistake. "CONFIG_GPIO_ASPEED_SGPIO" is used to
activate this driver.
Cc: Hongwei Zhang <hongweiz@ami.com>
Fixes: 7db47faae7 ("gpio: aspeed: Add SGPIO driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190927114833.12551-1-linus.walleij@linaro.org
Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of, mostly
minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS file,
making official his role as a reviewer.
-----BEGIN PGP SIGNATURE-----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=C9sW
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of,
mostly minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS
file, making official his role as a reviewer"
* tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (34 commits)
MAINTAINERS: Add myself as reviewer for the PWM subsystem
MAINTAINERS: Add patchwork link for PWM entry
MAINTAINERS: Add a selection of PWM related keywords to the PWM entry
pwm: mediatek: Add MT7629 compatible string
dt-bindings: pwm: Update bindings for MT7629 SoC
pwm: mediatek: Update license and switch to SPDX tag
pwm: mediatek: Use pwm_mediatek as common prefix
pwm: mediatek: Allocate the clks array dynamically
pwm: mediatek: Remove the has_clks field
pwm: mediatek: Drop the check for of_device_get_match_data()
pwm: atmel: Consolidate driver data initialization
pwm: atmel: Remove unneeded check for match data
pwm: atmel: Remove platform_device_id and use only dt bindings
pwm: stm32-lp: Add check in case requested period cannot be achieved
pwm: Ensure pwm_apply_state() doesn't modify the state argument
pwm: fsl-ftm: Don't update the state for the caller of pwm_apply_state()
pwm: sun4i: Don't update the state for the caller of pwm_apply_state()
pwm: rockchip: Don't update the state for the caller of pwm_apply_state()
pwm: Let pwm_get_state() return the last implemented state
pwm: Introduce local struct pwm_chip in pwm_apply_state()
...
It is surprising for a PWM consumer when the variable holding the
requested state is modified by pwm_apply_state(). Consider for example a
driver doing:
#define PERIOD 5000000
#define DUTY_LITTLE 10
...
struct pwm_state state = {
.period = PERIOD,
.duty_cycle = DUTY_LITTLE,
.polarity = PWM_POLARITY_NORMAL,
.enabled = true,
};
pwm_apply_state(mypwm, &state);
...
state.duty_cycle = PERIOD / 2;
pwm_apply_state(mypwm, &state);
For sure the second call to pwm_apply_state() should still have
state.period = PERIOD and not something the hardware driver chose for a
reason that doesn't necessarily apply to the second call.
So declare the state argument as a pointer to a const type and adapt all
drivers' .apply callbacks.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to
the Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver.
-----BEGIN PGP SIGNATURE-----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=2nNz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
The branch contains driver changes that are tightly
connected to SoC specific code. Aside from smaller
cleanups and bug fixes, here is a list of the notable
changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver
for its on-board pluggable extension bus. The
same platform also gains a firmware driver.
- The Samsung Exynos family gains a new Chipid driver
exporting using the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon
chips.
- A firmware driver for the NXP i.MX DSP IPC protocol
using shared memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the
NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for
the S905X3 and A311D chips
- A rework of the TI Davinci framebuffer driver to
allow important cleanups in the platform code
- A couple of device drivers for removed ARM SoC
platforms are removed. Most of the removals were
picked up by other maintainers, this contains
whatever was left.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lxFi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody is
using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still in
active use and are converted to the ARCH_MULTIPLATFORM build, meaning
that we can compile a kernel that works on these along with most other
ARMv5 platforms. Changes toward that goal are also merged for IOP32x,
but additional work is needed to complete this. Patches for the
remaining ARMv5 platforms have started but need more work and some
testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform
and the move of the TI Davinci platform to a new clocksource driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=u+ew
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
v5.4 kernel cycle.
Core changes:
- Support hierarchical GPIO irqchips. We now have three
consumers that can use this: Intel IXP4xx, ThunderX and
Qualcomm SPMI GPIO (in the pinctrl subsystem). The support
code has been long in the making and hashed out so it should
be easily adaptable for all hierarchical irqchip parents.
The code only gets compiled in if hierarchical irqchip
is used at the topmost irq controller at least, as the
hierarchical irqchip requires strict hierarchy all the
way up in the system.
- Determine the need for a "valid_mask" for GPIO lines on the
gpio_chip and conversely for the "valid_mask" for the GPIO
interrupt chip interrupt lines by looking for a
.init_valid_mask() callback in the main chip or GPIO interrupt
chip respectively. Allocate it with bitmap_alloc().
- Isolate the device tree/open firmware GPIO description code
out in its own file properly.
- Isolate the ACPI GPIO description code out in its own file
properly.
- Drop a whole lot of #ifdef:s in the main includes: it does
not hurt to keep the include items around, and we get
quicker and clearer compile failures if the appropriate
kernel symbols are not selected for drivers.
New/deleted drivers:
- New driver for Aspeed SGPIO.
- The KS8695 driver is deleted as the platform gets deleted
from arch/arm in this kernel cycle.
- The Cirrus Logic Madera driver now supports CS47L92 and
CS47L15.
- The Freescale MPC8xxx now supports LS1028A and LS1088A.
Driver improvements:
- We pass the GPIO irqchip intialization by directly filling
in the struct instead of using set-up functions (the new
way) for Intel MID, Lynxpoint, Merrifield, XLP, HLWD, Aspeed,
ZX, VF610, TQMX86, MT7621, Zynq and EP93xx.
Out-of-band changes:
- Fix a GPIO header inclusion in Unicore - no response from
maintainer.
- Drop FMC subsystem from MAINTAINERS - was deleted in the
GPIO tree last cycle so let's mop up the shards.
-----BEGIN PGP SIGNATURE-----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=/TRI
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of changes in the GPIO subsystem for the v5.4 kernel
cycle.
Core changes:
- Support hierarchical GPIO irqchips.
We now have three consumers that can use this: Intel IXP4xx,
ThunderX and Qualcomm SPMI GPIO (in the pinctrl subsystem).
The support code has been long in the making and hashed out so it
should be easily adaptable for all hierarchical irqchip parents.
The code only gets compiled in if hierarchical irqchip is used at
the topmost irq controller at least, as the hierarchical irqchip
requires strict hierarchy all the way up in the system.
- Determine the need for a "valid_mask" for GPIO lines on the
gpio_chip and conversely for the "valid_mask" for the GPIO
interrupt chip interrupt lines by looking for a .init_valid_mask()
callback in the main chip or GPIO interrupt chip respectively.
Allocate it with bitmap_alloc().
- Isolate the device tree/open firmware GPIO description code out in
its own file properly.
- Isolate the ACPI GPIO description code out in its own file
properly.
- Drop a whole lot of #ifdef:s in the main includes: it does not hurt
to keep the include items around, and we get quicker and clearer
compile failures if the appropriate kernel symbols are not selected
for drivers.
New/deleted drivers:
- New driver for Aspeed SGPIO.
- The KS8695 driver is deleted as the platform gets deleted from
arch/arm in this kernel cycle.
- The Cirrus Logic Madera driver now supports CS47L92 and CS47L15.
- The Freescale MPC8xxx now supports LS1028A and LS1088A.
Driver improvements:
- We pass the GPIO irqchip intialization by directly filling in the
struct instead of using set-up functions (the new way) for Intel
MID, Lynxpoint, Merrifield, XLP, HLWD, Aspeed, ZX, VF610, TQMX86,
MT7621, Zynq and EP93xx.
Out-of-band changes:
- Fix a GPIO header inclusion in Unicore - no response from
maintainer.
- Drop FMC subsystem from MAINTAINERS - was deleted in the GPIO tree
last cycle so let's mop up the shards"
* tag 'gpio-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (82 commits)
gpiolib: of: add a fallback for wlf,reset GPIO name
gpio: htc-egpio: Remove unused exported htc_egpio_get_wakeup_irq()
gpio: remove explicit comparison with 0
gpio: creg-snps: use devm_platform_ioremap_resource() to simplify code
gpio: devres: Switch to EXPORT_SYMBOL_GPL()
gpio: of: Switch to EXPORT_SYMBOL_GPL()
gpio: of: Make of_gpio_simple_xlate() private
gpio: of: Make of_get_named_gpiod_flags() private
gpio: aspeed: Add in ast2600 details to Aspeed driver
gpio: aspeed: Use ngpio property from device tree if available
gpio: aspeed: Setup irqchip dynamically
gpio/aspeed: Fix incorrect number of banks
gpio: aspeed: Update documentation with ast2600 controllers
gpio: Initialize the irqchip valid_mask with a callback
gpiolib: acpi: make acpi_can_fallback_to_crs() static
gpio: Fix further merge errors
gpio: Fix up merge collision in include file
gpio: of: Normalize return code variable name
gpio: gpiolib: Normalize return code variable name
gpio: ep93xx: Pass irqchip when adding gpiochip
...
The old Arizona binding did not use -gpio or -gpios suffix, so
devm_gpiod_get() does not work for it. As it is the one of a few users
of devm_gpiod_get_from_of_node() API that I want to remove, I'd rather
have a small quirk in the gpiolib OF handler, and switch Arizona
driver to devm_gpiod_get().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190911075215.78047-2-dmitry.torokhov@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This function was never used upstream, and is a relic of the original
handhelds.org code the htc-egpio driver was based on.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190910141529.21030-1-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No need to compare return value with 0. In case of non-zero
return value, the if condition will be true.
This makes intent a bit more clear to the reader.
"if (x) then", compared to "if (x is not zero) then".
Signed-off-by: Saiyam Doshi <saiyamdoshi.in@gmail.com>
Link: https://lore.kernel.org/r/20190907173910.GA9547@SD
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190906131032.22148-1-yuehaibing@huawei.com
Acked-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change all exported symbols for managed GPIO functions from
EXPORT_SYMBOL() to EXPORT_SYMBOL_GPL(), like is used for their
non-managed counterparts.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190906084539.21838-5-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 9a95e8d25a ("gpio: remove etraxfs driver"), there are
no more users of of_gpio_simple_xlate() outside gpiolib-of.c.
All GPIO drivers that need it now rely on of_gpiochip_add() setting it
up as the default translate function.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190906084539.21838-3-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit f626d6dfb7 ("gpio: of: Break out OF-only code"),
there are no more users of of_get_named_gpiod_flags() outside
gpiolib-of.c.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190906084539.21838-2-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ast2600 is a new generation of SoC from ASPEED. Similarly to the
ast2400 and ast2500, it has a GPIO controller for it's 3.3V GPIO pins.
Additionally, it has a GPIO controller for 1.8V GPIO pins.
As the register names for both controllers are the same and the 36 1.8V
GPIOs and the first 36 of the 3.3V GPIOs are all bidirectional, we can
use the same configuration struct and use the ngpio property to
differentiate between the two sets of GPIOs.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906063737.15428-1-rashmica.g@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the ngpio property from the device tree if it exists. If it doesn't
then fallback to the hardcoded value in the config.
This is in preparation for adding ast2600 support. The ast2600 SoC has
two GPIO controllers and so requires two instances of the GPIO driver.
We use the ngpio property to different between them as they have
different numbers of GPIOs.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906062727.13521-1-rashmica.g@gmail.com
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is in preparation for adding ast2600 support. The ast2600 SoC
requires two instances of the GPIO driver as it has two GPIO
controllers. Each instance needs it's own irqchip.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906062644.13445-1-rashmica.g@gmail.com
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current calculation for the number of GPIO banks is only correct if
the number of GPIOs is a multiple of 32 (if there were 31 GPIOs we would
currently say there are 0 banks, which is incorrect).
Fixes: 361b79119a ('gpio: Add Aspeed driver')
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190906062623.13354-1-rashmica.g@gmail.com
Reviewed-by: Joel Stanley <joel@jms.d.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Another day; another DSDT bug we need to workaround...
Since commit ca876c7483 ("gpiolib-acpi: make sure we trigger edge events
at least once on boot") we call _AEI edge handlers at boot.
In some rare cases this causes problems. One example of this is the Minix
Neo Z83-4 mini PC, this device has a clear DSDT bug where it has some copy
and pasted code for dealing with Micro USB-B connector host/device role
switching, while the mini PC does not even have a micro-USB connector.
This code, which should not be there, messes with the DDC data pin from
the HDMI connector (switching it to GPIO mode) breaking HDMI support.
To avoid problems like this, this commit adds a new
gpiolib_acpi.run_edge_events_on_boot kernel commandline option, which
allows disabling the running of _AEI edge event handlers at boot.
The default value is -1/auto which uses a DMI based blacklist, the initial
version of this blacklist contains the Neo Z83-4 fixing the HDMI breakage.
Cc: stable@vger.kernel.org
Cc: Daniel Drake <drake@endlessm.com>
Cc: Ian W MORRISON <ianwmorrison@gmail.com>
Reported-by: Ian W MORRISON <ianwmorrison@gmail.com>
Suggested-by: Ian W MORRISON <ianwmorrison@gmail.com>
Fixes: ca876c7483 ("gpiolib-acpi: make sure we trigger edge events at least once on boot")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20190827202835.213456-1-hdegoede@redhat.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ian W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After changing the valid_mask for the struct gpio_chip
to detect the need and presence of a valid mask with the
presence of a .init_valid_mask() callback to fill it in,
we augment the gpio_irq_chip to use the same logic.
Switch all driver using the gpio_irq_chio valid_mask
over to this new method.
This makes sure the valid_mask for the gpio_irq_chip gets
filled in when we add the gpio_chip, which makes it a
little easier to switch over drivers using the old
way of setting up gpio_irq_chip over to the new method
of passing the gpio_irq_chip along with the gpio_chip.
(See drivers/gpio/TODO for details.)
Cc: Joel Stanley <joel@jms.id.au>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20190904140104.32426-1-linus.walleij@linaro.org
It is not used outside gpiolib-acpi.c module, so there is no need to
export it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190904172624.GA76617@dtor-ws
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should only try to execute fallback quirks handling when previous
call returned -ENOENT, and not when we did not get -EPROBE_DEFER.
The other errors should be treated as hard errors: we did find the GPIO
description, but for some reason we failed to handle it properly.
The fallbacks should only be executed when previous handlers returned
-ENOENT, which means the mapping/description was not found.
Also let's remove the explicit deferral handling when iterating through
GPIO suffixes: it is not needed anymore as we will not be calling
fallbacks for anything but -ENOENT.
Fixes: df451f83e1 ("gpio: of: fix Freescale SPI CS quirk handling")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190903231856.GA165165@dtor-ws
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clean up of IRQ chip initialization has been done in few drivers.
Stale record in MAINTAINERS database is removed.
The following is an automated git shortlog grouped by driver:
intel-mid:
- Pass irqchip when adding gpiochip
- MAINTAINERS: Remove stale record for gpio-intel-mid.c
lynxpoint:
- Pass irqchip when adding gpiochip
merrifield:
- Pass irqchip when adding gpiochip
pch:
- Use dev_get_drvdata
-----BEGIN PGP SIGNATURE-----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=0wOc
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel
intel-gpio for v5.4-1
The clean up of IRQ chip initialization has been done in few drivers.
Stale record in MAINTAINERS database is removed.
The following is an automated git shortlog grouped by driver:
intel-mid:
- Pass irqchip when adding gpiochip
- MAINTAINERS: Remove stale record for gpio-intel-mid.c
lynxpoint:
- Pass irqchip when adding gpiochip
merrifield:
- Pass irqchip when adding gpiochip
pch:
- Use dev_get_drvdata
lineevent_create should not allow any of GPIOHANDLE_REQUEST_OUTPUT,
GPIOHANDLE_REQUEST_OPEN_DRAIN or GPIOHANDLE_REQUEST_OPEN_SOURCE to be set.
Fixes: d7c51b47ac ("gpio: userspace ABI for reading/writing GPIO lines")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
linehandle_create should not allow both GPIOHANDLE_REQUEST_INPUT
and GPIOHANDLE_REQUEST_OUTPUT to be set.
Fixes: d7c51b47ac ("gpio: userspace ABI for reading/writing GPIO lines")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When using single_open() for opening, single_release() should be
used instead of seq_release(), otherwise there is a memory leak.
Fixes: 2a9e27408e ("gpio: mockup: rework debugfs interface")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The previous merge of v5.3-rc7 was struggle enough, now it
gave rise to new errors and now I fix those too.
Fixes: 151a41014b ("Merge tag 'v5.3-rc7' into devel")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is confusing to name return variables mixedly "status",
"err" or "ret". I just changed them all to "ret", by personal
preference, to lower cognitive stress.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190716115854.12098-1-linus.walleij@linaro.org
It is confusing to name return variables mixedly "status",
"err" or "ret". I just changed them all to "ret", by personal
preference, to lower cognitive stress.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190716091145.8235-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Thierry Reding <treding@nvidia.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190812130000.22252-1-linus.walleij@linaro.org
- use a helper variable for &pdev->dev in gpio-em
- tweak the ifdefs in GPIO headers
- fix function links in HTML docs
- remove an unneeded error message from ixp4xx
- use the optional clk_get in gpio-mxc instead of checking the return value
- a couple improvements in pca953x
- allow to build gpio-lpc32xx on non-lpc32xx targets
-----BEGIN PGP SIGNATURE-----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=6y9c
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.4-updates-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio: updates for v5.4
- use a helper variable for &pdev->dev in gpio-em
- tweak the ifdefs in GPIO headers
- fix function links in HTML docs
- remove an unneeded error message from ixp4xx
- use the optional clk_get in gpio-mxc instead of checking the return value
- a couple improvements in pca953x
- allow to build gpio-lpc32xx on non-lpc32xx targets
The register number needs to be translated for chips with more than 8
ports. This patch fixes a bug causing all chips with more than 8 GPIO pins
to not work correctly.
Fixes: 0f25fda840 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
Cc: Cc: <stable@vger.kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The type of reg_direction needs to match the type of the regmap, which
is u8.
Fixes: 0f25fda840 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
Cc: Cc: <stable@vger.kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190809132649.25176-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
This driver requests the IRQ directly in the driver so it
differs a bit from the others.
Cc: Greg Ungerer <gerg@kernel.org>
Cc: Nicholas Mc Guire <hofrat@osadl.org>
Cc: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: René van Dorst <opensource@vdorst.com>
Link: https://lore.kernel.org/r/20190809141116.16403-1-linus.walleij@linaro.org
If 'devm_kcalloc()' fails, we should go through the error handling path,
should some clean-up be needed.
Fixes: 42d9fc7176 ("gpio: ftgpio: Pass irqchip when adding gpiochip")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20190822204538.4791-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The user space like gpioinfo only see the GPIO usage but not the
MUX usage (e.g. I2C or SPI usage) of a pin. As a user we want
to know which pin is free/safe to use. So take the MUX usage of
strict pinmux controllers into account to get a more realistic
view for ioctl GPIO_GET_LINEINFO_IOCTL.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/20190814110035.13451-1-ramon.fried@linux.intel.com
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new API for registering a gpio_irq_chip along with a
gpio_chip has a different semantic ordering than the old
API which added the irqchip explicitly after registering
the gpio_chip.
Move the calls to add the gpio_irq_chip *last* in the
function, so that the different hooks setting up OF and
ACPI and machine gpio_chips are called *before* we try
to register the interrupts, preserving the elder semantic
order.
This cropped up in the PL061 driver which used to work
fine with no special ACPI quirks, but started to misbehave
using the new API.
Fixes: e0d8972898 ("gpio: Implement tighter IRQ chip integration")
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Reported-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190820080527.11796-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190809144045.26018-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190809141916.20999-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190809133845.30991-1-linus.walleij@linaro.org
ls1028a and ls1088a platform share common special function.
The gpio hardware what they use is the same version.
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Link: https://lore.kernel.org/r/20190808101628.36782-3-hui.song_1@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Do not expose the base VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After we switched the two drivers that have .need_valid_mask
set to use the callback for setting up the .valid_mask,
we can just use the presence of the .init_valid_mask()
callback (or the OF reserved ranges, nota bene) to determine
whether to allocate the mask or not and we can drop the
.need_valid_mask field altogether.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190819093058.10863-1-linus.walleij@linaro.org
It is more helpful for drivers to have the affected fields
directly available when we use the callback to set up the
valid mask. Change this and switch over the only user
(MSM) to use the passed parameters. If we do this we can
also move the mask out of publicly visible struct fields.
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190819084904.30027-1-linus.walleij@linaro.or
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
config GPIO_MOCKUP is defined in a big if GPIOLIB ... endif block so it
doesn't need to depend explicitly on GPIOLIB.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20190725131002.14597-1-uwe@kleine-koenig.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On the gta04 we see:
spi_gpio: probe of spi_lcd failed with error -2
The quirk introduced in
commit e3023bf806 ("gpio: of: Handle the Freescale SPI CS")
can also be triggered by a temporary -EPROBE_DEFER and
so "convert" it to a hard -ENOENT.
Disable that conversion by checking for -EPROBE_DEFER.
Fixes: e3023bf806 ("gpio: of: Handle the Freescale SPI CS")
Suggested-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20190816165000.32334-1-andreas@kemnade.info
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I revisited some older patches here, getting two of the remaining
ARM platforms to build with ARCH_MULTIPLATFORM like most others do.
In case of lpc32xx, I created a new set of patches, which seemed
easier than digging out what I did for an older release many
years ago.
* lpc32xx/multiplatform:
ARM: lpc32xx: allow multiplatform build
ARM: lpc32xx: clean up header files
serial: lpc32xx: allow compile testing
net: lpc-enet: allow compile testing
net: lpc-enet: fix printk format strings
net: lpc-enet: fix badzero.cocci warnings
net: lpc-enet: move phy setup into platform code
net: lpc-enet: factor out iram access
gpio: lpc32xx: allow building on non-lpc32xx targets
serial: lpc32xx_hs: allow compile-testing
watchdog: pnx4008_wdt: allow compile-testing
usb: udc: lpc32xx: allow compile-testing
usb: ohci-nxp: enable compile-testing
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The driver uses hardwire MMIO addresses instead of the data
that is passed in device tree. Change it over to only
hardcode the register offset values and allow compile-testing.
Link: https://lore.kernel.org/r/20190809144043.476786-6-arnd@arndb.de
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20190809125515.19094-1-linus.walleij@linaro.org
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20190809140005.11654-1-linus.walleij@linaro.org
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Tested-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Jayachandran C <jnair@caviumnetworks.com>
Cc: Kamlakant Patel <kamlakant.patel@broadcom.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190809135119.6946-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Jan Kotas <jank@cadence.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jan Kotas <jank@cadence.com>
Link: https://lore.kernel.org/r/20190809131804.20352-1-linus.walleij@linaro.org
Use the new infrastructure for hierarchical irqchips in
gpiolib.
The major part of the rewrite was dues to the fact that
the driver was passing around a per-irq pointer to
struct thunderx_line * data container, and the central
handlers will assume struct gpio_chip * to be passed
to we need to use the hwirq as index to look up the
struct thunderx_line * for each IRQ.
The pushing and pop:ing of the irqdomain was confusing
because I've never seen this before, but I tried to
replicate it as best I could.
I have no chance to test or debug this so I need
help.
Cc: David Daney <david.daney@cavium.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190808123242.5359-4-linus.walleij@linaro.org
This modifies the IXP4xx driver to use the new helpers
to handle the remapping of parent to child hardware irqs
in the gpiolib core.
This pulls the majority of the code out of the driver
and use the generic code in gpiolib.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: Bitan Biswas <bbiswas@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Cc: Thierry Reding <treding@nvidia.com>
Cc: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190808123242.5359-2-linus.walleij@linaro.org
Hierarchical IRQ domains can be used to stack different IRQ
controllers on top of each other.
Bring hierarchical IRQ domains into the GPIOLIB core with the
following basic idea:
Drivers that need their interrupts handled hierarchically
specify a callback to translate the child hardware IRQ and
IRQ type for each GPIO offset to a parent hardware IRQ and
parent hardware IRQ type.
Users have to pass the callback, fwnode, and parent irqdomain
before calling gpiochip_irqchip_add().
We use the new method of just filling in the struct
gpio_irq_chip before adding the gpiochip for all hierarchical
irqchips of this type.
The code path for device tree is pretty straight-forward,
while the code path for old boardfiles or anything else will
be more convoluted requireing upfront allocation of the
interrupts when adding the chip.
One specific use-case where this can be useful is if a power
management controller has top-level controls for wakeup
interrupts. In such cases, the power management controller can
be a parent to other interrupt controllers and program
additional registers when an IRQ has its wake capability
enabled or disabled.
The hierarchical irqchip helper code will only be available
when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using
this should select or depend on that symbol. When using
hierarchical IRQs, the parent interrupt controller must
also be hierarchical all the way up to the top interrupt
controller wireing directly into the CPU, so on systems
that do not have this we can get rid of all the extra
code for supporting hierarchical irqs.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: Bitan Biswas <bbiswas@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Cc: David Daney <david.daney@cavium.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Brian Masney <masneyb@onstation.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Co-developed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
There are three families of IOP machines we support in Linux: iop32x
(which includes EP80219), iop33x and iop13xx (aka IOP34x aka WP8134x).
All products we support in the kernel are based on the first of these,
iop32x, the other families only ever supported the Intel reference
boards but no actual machine anyone could ever buy.
While one could clearly make them all three work in a single kernel
with some work, this takes the easy way out, removing the later two
platforms entirely, under the assumption that there are no remaining
users.
Earlier versions of OpenWRT and Debian both had support for iop32x
but not the others, and they both dropped iop32x as well in their 2015
releases.
Link: https://lore.kernel.org/r/20190809163334.489360-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C parts
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds support for interpreting the input and output bits of one
device on Moxtet bus as GPIOs.
This is needed for example by the SFP cage module of Turris Mox.
Link: https://lore.kernel.org/r/20190812161118.21476-5-marek.behun@nic.cz
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
If the driver doesn't support open-drain/source config options, we
emulate this behavior when setting the direction by calling
gpiod_direction_input() if the default value is 0 (open-source) or
1 (open-drain), thus not actively driving the line in those cases.
This however clears the FLAG_IS_OUT bit for the GPIO line descriptor
and makes the LINEINFO ioctl() incorrectly report this line's mode as
'input' to user-space.
This commit modifies the ioctl() to always set the GPIOLINE_FLAG_IS_OUT
bit in the lineinfo structure's flags field. Since it's impossible to
use the input mode and open-drain/source options at the same time, we
can be sure the reported information will be correct.
Fixes: 521a2ad6f8 ("gpio: add userspace ABI for GPIO line information")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190806114151.17652-1-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The driver uses hardwire MMIO addresses instead of the data
that is passed in device tree. Change it over to only
hardcode the register offset values and allow compile-testing.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-16-swboyd@chromium.org
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the gpio is common to all madera codecs all that is needed
is to setup the correct number of GPIO pins for the CS47L92.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20190722090748.20807-4-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the gpio is common to all madera codecs all that is needed
is to setup the correct number of GPIO pins for the CS47L15.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20190722090748.20807-3-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Refactor gpiochip_allocate_mask() slightly by using bitmap_alloc().
I used bitmap_free() for the corresponding free parts. Actually,
bitmap_free() is a wrapper of kfree(), but I did this for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20190718065101.26994-1-yamada.masahiro@socionext.com
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a device specify register(named GPIO_IBE)
on ls1028a need to enable in initial stage.
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Link: https://lore.kernel.org/r/20190718094902.15562-2-hui.song_1@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to use %s for constant string literals
w/o special characters inside.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There is no need to explicitly compare return code with 0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Use GENMASK() macro for all definitions where it's appropriate.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Instead of open coded variants, switch to direct use of
device_get_match_data().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
i.MX SoC's GPIO clock is optional, so it is better to use
devm_clk_get_optional instead of devm_clk_get.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The recent refactoring to break out OF code to its own file
contained a bug letting the need_valid_mask
be overridden by the need of the device tree range check,
and if there were no ranges, but device tree was active
and the reserved GPIO used in another way, things likely
crash.
Cc: Mark Brown <broonie@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Fixes: f626d6dfb7 ("gpio: of: Break out OF-only code")
Reported-by: Mark Brown <broonie@kernel.org>
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The API, which belongs to GPIO library, is foreign to ACPI headers. Earlier
we moved out I²C out of the latter, and now it's time for
acpi_dev_add_driver_gpios() et al.
For time being the acpi_gpio_get_irq_resource() and acpi_dev_gpio_irq_get()
are left untouched as they need more thought about.
Note, it requires uninline acpi_dev_remove_driver_gpios() to keep purity of
consumer.h.
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Cc: Jie Yang <yang.jie@linux.intel.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: alsa-devel@alsa-project.org (moderated list:INTEL ASoC DRIVERS)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190730104337.21235-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a follow up to the commit
f626d6dfb7 ("gpio: of: Break out OF-only code")
which broke down OF parts of GPIO library. Here we do the similar to ACPI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190730104337.21235-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Define a MODULE_ALIAS() in the gpio sub-driver for max77650 so that
the appropriate module gets loaded together with the core mfd driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190703084601.9276-1-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The core gpiolib should not contain any OF/device tree-only
code. Try to break out the main part of it and push it down
into the optional gpiolib-of.c part of the library.
Create a local gpiolib-of.h header and move stuff around a
bit to get a clean cut.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190717071001.3858-1-linus.walleij@linaro.org
Variable ret is being initialized with a value that is never read
and ret is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190629123306.12519-1-colin.king@canonical.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When a pin is active-low, logical trigger edge should be inverted to match
the same interrupt opportunity.
For example, a button pushed triggers falling edge in ACTIVE_HIGH case; in
ACTIVE_LOW case, the button pushed triggers rising edge. For user space the
IRQ requesting doesn't need to do any modification except to configuring
GPIOHANDLE_REQUEST_ACTIVE_LOW.
For example, we want to catch the event when the button is pushed. The
button on the original board drives level to be low when it is pushed, and
drives level to be high when it is released.
In user space we can do:
req.handleflags = GPIOHANDLE_REQUEST_INPUT;
req.eventflags = GPIOEVENT_REQUEST_FALLING_EDGE;
while (1) {
read(fd, &dat, sizeof(dat));
if (dat.id == GPIOEVENT_EVENT_FALLING_EDGE)
printf("button pushed\n");
}
Run the same logic on another board which the polarity of the button is
inverted; it drives level to be high when pushed, and level to be low when
released. For this inversion we add flag GPIOHANDLE_REQUEST_ACTIVE_LOW:
req.handleflags = GPIOHANDLE_REQUEST_INPUT |
GPIOHANDLE_REQUEST_ACTIVE_LOW;
req.eventflags = GPIOEVENT_REQUEST_FALLING_EDGE;
At the result, there are no any events caught when the button is pushed.
By the way, button releasing will emit a "falling" event. The timing of
"falling" catching is not expected.
Cc: stable@vger.kernel.org
Signed-off-by: Michael Wu <michael.wu@vatics.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Instead of always dereferencing &pdev->dev, just assign a helper local
variable of type struct device * and use it where applicable.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Revert a SPIO GPIO fix that didn't fix anything instead created new
problems.
- Remove the EM GPIO irqdomain in a safe manner.
- Fix a memory leak in the gpio quirks.
- Make the DaVinci error path silent on probe deferral.
-----BEGIN PGP SIGNATURE-----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=/5s0
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- Revert a SPIO GPIO fix that didn't fix anything but instead created
new problems.
- Remove the EM GPIO irqdomain in a safe manner.
- Fix a memory leak in the gpio quirks.
- Make the DaVinci error path silent on probe deferral.
* tag 'gpio-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
Revert "gpio/spi: Fix spi-gpio regression on active high CS"
gpio: em: remove the gpiochip before removing the irq domain
gpiolib: of: fix a memory leak in of_gpio_flags_quirks()
gpio: davinci: silence error prints in case of EPROBE_DEFER
-----BEGIN PGP SIGNATURE-----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=smxY
-----END PGP SIGNATURE-----
Merge tag 'docs/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull rst conversion of docs from Mauro Carvalho Chehab:
"As agreed with Jon, I'm sending this big series directly to you, c/c
him, as this series required a special care, in order to avoid
conflicts with other trees"
* tag 'docs/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (77 commits)
docs: kbuild: fix build with pdf and fix some minor issues
docs: block: fix pdf output
docs: arm: fix a breakage with pdf output
docs: don't use nested tables
docs: gpio: add sysfs interface to the admin-guide
docs: locking: add it to the main index
docs: add some directories to the main documentation index
docs: add SPDX tags to new index files
docs: add a memory-devices subdir to driver-api
docs: phy: place documentation under driver-api
docs: serial: move it to the driver-api
docs: driver-api: add remaining converted dirs to it
docs: driver-api: add xilinx driver API documentation
docs: driver-api: add a series of orphaned documents
docs: admin-guide: add a series of orphaned documents
docs: cgroup-v1: add it to the admin-guide book
docs: aoe: add it to the driver-api book
docs: add some documentation dirs to the driver-api book
docs: driver-model: move it to the driver-api book
docs: lp855x-driver.rst: add it to the driver-api book
...
- silence error messages on probe deferral in gpio-davinci
- fix a memory leak in gpiolib-of
- fix a potential use-after-free error in gpio-em
-----BEGIN PGP SIGNATURE-----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=QeTx
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.3-rc1-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into fixes
GPIO fixes for v5.3-rc1
- silence error messages on probe deferral in gpio-davinci
- fix a memory leak in gpiolib-of
- fix a potential use-after-free error in gpio-em
This reverts commit fbbf145a0e.
It seems I was misguided in my fixup, which was working at the
time but did not work on the final v5.2.
The patch tried to avoid a quirk the gpiolib code not to treat
"spi-gpio" CS gpios "special" by enforcing them to be active
low, in the belief that since the "spi-gpio" driver was
parsing the device tree on its own, it did not care to inspect
the "spi-cs-high" attribute on the device nodes.
That's wrong. The SPI core was inspecting them inside the
of_spi_parse_dt() funtion and setting SPI_CS_HIGH on the
nodes, and the driver inspected this flag when driving the
line.
As of now, the core handles the GPIO and it will consistently
set the GPIO descriptor to 1 to enable CS, strictly requireing
the gpiolib to invert it. And the gpiolib should indeed
enforce active low on the CS line.
Device trees should of course put the right flag on the GPIO
handles, but it used to not matter. If we don't enforce active
low on "gpio-gpio" we may run into ABI backward compatibility
issues, so revert this.
Cc: linux-spi@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190715204529.9539-1-linus.walleij@linaro.org
Pull i2c updates from Wolfram Sang:
"New stuff from the I2C world:
- in the core, getting irqs from ACPI is now similar to OF
- new driver for MediaTek MT7621/7628/7688 SoCs
- bcm2835, i801, and tegra drivers got some more attention
- GPIO API cleanups
- cleanups in the core headers
- lots of usual driver updates"
* 'i2c/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (74 commits)
i2c: mt7621: Fix platform_no_drv_owner.cocci warnings
i2c: cpm: remove casting dma_alloc
dt-bindings: i2c: sun6i-p2wi: Fix the binding example
dt-bindings: i2c: mv64xxx: Fix the example compatible
i2c: i801: Documentation update
i2c: i801: Add support for Intel Tiger Lake
i2c: i801: Fix PCI ID sorting
dt-bindings: i2c-stm32: document optional dmas
i2c: i2c-stm32f7: Add I2C_SMBUS_I2C_BLOCK_DATA support
i2c: core: Tidy up handling of init_irq
i2c: core: Move ACPI gpio IRQ handling into i2c_acpi_get_irq
i2c: core: Move ACPI IRQ handling to probe time
i2c: acpi: Factor out getting the IRQ from ACPI
i2c: acpi: Use available IRQ helper functions
i2c: core: Allow whole core to use i2c_dev_irq_from_resources
eeprom: at24: modify a comment referring to platform data
dt-bindings: i2c: omap: Add new compatible for J721E SoCs
dt-bindings: i2c: mv64xxx: Add YAML schemas
dt-bindings: i2c: sun6i-p2wi: Add YAML schemas
i2c: mt7621: Add MediaTek MT7621/7628/7688 I2C driver
...
- Set 'struct device' fwnode when registering a new device
- New Drivers
- Add support for ROHM BD70528 PMIC
- New Device Support
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
- New Functionality
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
- Fix-ups
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
- Bug Fixes
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera
-----BEGIN PGP SIGNATURE-----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=A3jw
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Set 'struct device' fwnode when registering a new device
New Drivers:
- Add support for ROHM BD70528 PMIC
New Device Support:
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
New Functionality:
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
Fix-ups:
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
Bug Fixes:
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera"
* tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (45 commits)
mfd: hi655x-pmic: Fix missing return value check for devm_regmap_init_mmio_clk
mfd: madera: Fixup SPDX headers
mfd: madera: Remove some unused registers and fix some defaults
mfd: intel-lpss: Release IDA resources
mfd: intel-lpss: Add Intel Elkhart Lake PCH PCI IDs
mfd: cs5535-mfd: Remove ifdef OLPC noise
mfd: stmfx: Fix macro definition spelling
dt-bindings: mfd: Add link to ROHM BD71847 Datasheet
MAINAINERS: Swap words in INTEL PMIC MULTIFUNCTION DEVICE DRIVERS
mfd: cros_ec_dev: Register cros_ec_accel_legacy driver as a subdevice
mfd: rk808: Prepare rk805 for poweroff
mfd: rk808: Check pm_power_off pointer
mfd: cros_ec: differentiate SCP from EC by feature bit
dt-bindings: Add binding for cros-ec-rpmsg
mfd: madera: Add Madera core support for CS47L92
mfd: madera: Add Madera core support for CS47L15
mfd: madera: Update DT bindings to add additional CODECs
mfd: madera: Add supply mapping for MICVDD
mfd: madera: Fix potential uninitialised use of variable
mfd: madera: Fix bad reference to pinctrl.txt file
...
There are lots of documents under Documentation/*.txt and a few other
orphan documents elsehwere that belong to the driver-API book.
Move them to their right place.
Reviewed-by: Cornelia Huck <cohuck@redhat.com> # vfio-related parts
Acked-by: Logan Gunthorpe <logang@deltatee.com> # switchtec
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The audience for the Kernel driver-model is clearly Kernel hackers.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> # ice driver changes
In commit 8764c4ca50 ("gpio: em: use the managed version of
gpiochip_add_data()") we implicitly altered the ordering of resource
freeing: since gpiochip_remove() calls gpiochip_irqchip_remove()
internally, we now can potentially use the irq_domain after it was
destroyed in the remove() callback (as devm resources are freed after
remove() has returned).
Use devm_add_action_or_reset() to keep the ordering right and entirely
kill the remove() callback in the driver.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 8764c4ca50 ("gpio: em: use the managed version of gpiochip_add_data()")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a break from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the break.
Issue found with Coccinelle.
Cc: <stable@vger.kernel.org>
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
[Bartosz: tweaked the commit message]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Silence error prints in case of EPROBE_DEFER. This avoids
multiple/duplicate defer prints during boot.
Cc: <stable@vger.kernel.org>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
A couple of new features in the core, the most interesting one
being support for complex regulator coupling configurations
initially targeted at nVidia Tegra SoCs, and some new drivers but
otherwise quite a quiet release.
- Core support for gradual ramping of voltages for devices that
can't manage large changes in hardware from Bartosz Golaszewski.
- Core support for systems that have complex coupling requirements
best described via code, contributed by Dmitry Osipenko.
- New drivers for Dialog SLG51000, Qualcomm PM8005 and ST
Microelectronics STM32-Booster.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl0jIZwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0PG+B/9EQnjM29THpBKM6bKdl8cYcf3Hq/FX
KNtXjwaTM0DqYtpk1RkaHgecxTJwesJ0k9AYijh0ieeMhb5UES280+6B4NqPb7xr
UmFBbNcdk9G+x9q1TyT8akRMkCugEMscQodyk4npzZRjGv8qUsNJUY71Bq2T/JJx
QXo5fKlWICzBahF87DCB5pKC7PKfNkx3BWCrGGXOqoBX2ZEKytyWlCa0nGUZ+LqL
GqXmmIjKL7H8MP3avmrrRHYpeF5DLXAzH+HEIM9Y0F1cRcdgOS1Exv2eG+90a634
yybVDBX2d5zfiEIoRnpldtB52EGXjvwbo7w1mFwh9UgJRbOCZgb+ZQXT
=26r6
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A couple of new features in the core, the most interesting one being
support for complex regulator coupling configurations initially
targeted at nVidia Tegra SoCs, and some new drivers but otherwise
quite a quiet release.
Summary:
- Core support for gradual ramping of voltages for devices that can't
manage large changes in hardware from Bartosz Golaszewski.
- Core support for systems that have complex coupling requirements
best described via code, contributed by Dmitry Osipenko.
- New drivers for Dialog SLG51000, Qualcomm PM8005 and ST
Microelectronics STM32-Booster"
* tag 'regulator-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (52 commits)
regulator: max77650: use vsel_step
regulator: implement selector stepping
regulator: max77650: add MODULE_ALIAS()
regulator: max77620: remove redundant assignment to variable ret
dt-bindings: regulator: add support for the stm32-booster
regulator: add support for the stm32-booster
regulator: s2mps11: Adjust supported buck voltages to real values
regulator: s2mps11: Fix buck7 and buck8 wrong voltages
gpio: Fix return value mismatch of function gpiod_get_from_of_node()
regulator: core: Expose some of core functions needed by couplers
regulator: core: Introduce API for regulators coupling customization
regulator: s2mps11: Add support for disabling S2MPS11 regulators in suspend
regulator: s2mps11: Reduce number of rdev_get_id() calls
regulator: qcom_spmi: Do NULL check for lvs
regulator: qcom_spmi: Fix math of spmi_regulator_set_voltage_time_sel
regulator: da9061/62: Adjust LDO voltage selection minimum value
regulator: s2mps11: Fix ERR_PTR dereference on GPIO lookup failure
regulator: qcom_spmi: add PMS405 SPMI regulator
dt-bindings: qcom_spmi: Document pms405 support
arm64: dts: msm8998-mtp: Add pm8005_s1 regulator
...
Core:
- When a gpio_chip request GPIOs from itself, it can now fully
control the line characteristics, both machine and consumer
flags. This makes a lot of sense, but took some time before I
figured out that this is how it has to work.
- Several smallish documentation fixes.
New drivers:
- The PCA953x driver now supports the TI TCA9539.
- The DaVinci driver now supports the K3 AM654 SoCs.
Driver improvements:
- Major overhaul and hardening of the OMAP driver by Russell
King.
- Starting to move some drivers to the new API passing irq_chip
along with the gpio_chip when adding the gpio_chip instead
of adding it separately.
Unrelated:
- Delete the FMC subsystem.
-----BEGIN PGP SIGNATURE-----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=8zSV
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the big slew of GPIO changes for the v5.3 kernel cycle. This
is mostly incremental work this time.
Three important things:
- The FMC subsystem is deleted through my tree. This happens through
GPIO as its demise was discussed in relation to a patch decoupling
its GPIO implementation from the standard way of handling GPIO. As
it turns out, that is not the only subsystem it reimplements and
the authors think it is better do scratch it and start over using
the proper kernel subsystems than try to polish the rust shiny. See
the commit (ACKed by the maintainers) for details.
- Arnd made a small devres patch that was ACKed by Greg and goes into
the device core.
- SPDX header change colissions may happen, because at times I've
seen that quite a lot changed during the -rc:s in regards to SPDX.
(It is good stuff, tglx has me convinced, and it is worth the
occasional pain.)
Apart from this is is nothing controversial or problematic.
Summary:
Core:
- When a gpio_chip request GPIOs from itself, it can now fully
control the line characteristics, both machine and consumer flags.
This makes a lot of sense, but took some time before I figured out
that this is how it has to work.
- Several smallish documentation fixes.
New drivers:
- The PCA953x driver now supports the TI TCA9539.
- The DaVinci driver now supports the K3 AM654 SoCs.
Driver improvements:
- Major overhaul and hardening of the OMAP driver by Russell King.
- Starting to move some drivers to the new API passing irq_chip along
with the gpio_chip when adding the gpio_chip instead of adding it
separately.
Unrelated:
- Delete the FMC subsystem"
* tag 'gpio-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: tegra: Clean-up debugfs initialisation"
gpiolib: Use spinlock_t instead of struct spinlock
gpio: stp-xway: allow compile-testing
gpio: stp-xway: get rid of the #include <lantiq_soc.h> dependency
gpio: stp-xway: improve module clock error handling
gpio: stp-xway: simplify error handling in xway_stp_probe()
gpiolib: Clarify use of non-sleeping functions
gpiolib: Fix references to gpiod_[gs]et_*value_cansleep() variants
gpiolib: Document new gpio_chip.init_valid_mask field
Documentation: gpio: Fix reference to gpiod_get_array()
gpio: pl061: drop duplicate printing of device name
gpio: altera: Pass irqchip when adding gpiochip
gpio: siox: Use devm_ managed gpiochip
gpio: siox: Add struct device *dev helper variable
gpio: siox: Pass irqchip when adding gpiochip
drivers: gpio: amd-fch: make resource struct const
devres: allow const resource arguments
gpio: ath79: Pass irqchip when adding gpiochip
gpio: tegra: Clean-up debugfs initialisation
gpio: siox: Switch to IRQ_TYPE_NONE
...
Pull irq updates from Thomas Gleixner:
"The irq departement provides the usual mixed bag:
Core:
- Further improvements to the irq timings code which aims to predict
the next interrupt for power state selection to achieve better
latency/power balance
- Add interrupt statistics to the core NMI handlers
- The usual small fixes and cleanups
Drivers:
- Support for Renesas RZ/A1, Annapurna Labs FIC, Meson-G12A SoC and
Amazon Gravition AMR/GIC interrupt controllers.
- Rework of the Renesas INTC controller driver
- ACPI support for Socionext SoCs
- Enhancements to the CSKY interrupt controller
- The usual small fixes and cleanups"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
irq/irqdomain: Fix comment typo
genirq: Update irq stats from NMI handlers
irqchip/gic-pm: Remove PM_CLK dependency
irqchip/al-fic: Introduce Amazon's Annapurna Labs Fabric Interrupt Controller Driver
dt-bindings: interrupt-controller: Add Amazon's Annapurna Labs FIC
softirq: Use __this_cpu_write() in takeover_tasklets()
irqchip/mbigen: Stop printing kernel addresses
irqchip/gic: Add dependency for ARM_GIC_MAX_NR
genirq/affinity: Remove unused argument from [__]irq_build_affinity_masks()
genirq/timings: Add selftest for next event computation
genirq/timings: Add selftest for irqs circular buffer
genirq/timings: Add selftest for circular array
genirq/timings: Encapsulate storing function
genirq/timings: Encapsulate timings push
genirq/timings: Optimize the period detection speed
genirq/timings: Fix timings buffer inspection
genirq/timings: Fix next event index function
irqchip/qcom: Use struct_size() in devm_kzalloc()
irqchip/irq-csky-mpintc: Remove unnecessary loop in interrupt handler
dt-bindings: interrupt-controller: Update csky mpintc
...
For spinlocks the type spinlock_t should be used instead of "struct
spinlock".
Use spinlock_t for spinlock's definition.
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20190704153803.12739-8-bigeasy@linutronix.de
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable compile-testing of the stp-xway GPIO driver now that it does not
depend on any architecture specific includes anymore.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20190702223248.31934-5-martin.blumenstingl@googlemail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the xway_stp_{r,w}32 helpers in xway_stp_w32_mask instead of relying
on ltq_{r,w}32 from the architecture specific <lantiq_soc.h>.
This will allow the driver to be compile-tested on all architectures
that support MMIO.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20190702223248.31934-4-martin.blumenstingl@googlemail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Three module clock error handling improvements:
- use devm_clk_get() so the clock instance can be freed if
devm_gpiochip_add_data() fails later on
- switch to clk_prepare_enable() so the driver is ready whenever the
lantiq target switches to the common clock framework
- disable the clock again (using clk_disable_unprepare()) if
devm_gpiochip_add_data()
All of these are virtually no-ops with the current lantiq target.
However, these will be relevant if we switch to the common clock
framework.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20190702223248.31934-3-martin.blumenstingl@googlemail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Return early if devm_gpiochip_add_data() returns an error instead of
having two consecutive "if (!ret) ..." statements.
Also make xway_stp_hw_init() return void because it unconditionally
returns 0. While here also update the kerneldoc comment for
xway_stp_hw_init().
These changes makes the error handling within the driver consistent.
No functional changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20190702223248.31934-2-martin.blumenstingl@googlemail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Obviously functions that are safe to be called from atomic contexts, can
be called from non-atomic contexts, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190701142809.25308-1-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 372e722ea4 ("gpiolib: use descriptors internally") renamed
the functions to use a "gpiod" prefix, and commit 79a9becda8
("gpiolib: export descriptor-based GPIO interface") introduced the "raw"
variants, but both changes forgot to update the comments.
Readd a similar reference to gpiod_set_value(), which was accidentally
removed by commit 1e77fc8211 ("gpio: Add missing open drain/source
handling to gpiod_set_value_cansleep()").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190701142738.25219-1-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The dev_info() call already prints the device name, so there's
no need to explicitly include it in the message for second time.
Signed-off-by: Enrico Weigelt <info@metux.net>
Link: https://lore.kernel.org/r/1562146944-4162-1-git-send-email-info@metux.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Tien Hock Loh <thloh@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By using devm_gpiochip_add_data() we can get rid of the
remove() callback. As this driver doesn't use the
gpiochip data pointer we simply pass in NULL.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
