This patch adds a workaround for an IOMMU BIOS problem to
the AMD IOMMU driver. The result of the bug is that the
IOMMU does not execute commands anymore when the system
comes out of the S3 state resulting in system failure. The
bug in the BIOS is that is does not restore certain hardware
specific registers correctly. This workaround reads out the
contents of these registers at boot time and restores them
on resume from S3. The workaround is limited to the specific
IOMMU chipset where this problem occurs.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch moves the setting of the configuration and
feature flags out out the acpi table parsing path and moves
it into the iommu-enable path. This is needed to reliably
fix resume-from-s3.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The guest can use the paravirt clock in kvmclock.c which is used
by sched_clock(), which in turn is used by the tracing mechanism
for timestamps, which leads to infinite recursion.
Disable mcount/tracing for kvmclock.o.
Cc: stable@kernel.org
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When using a paravirt clock, pvclock.c can be used by sched_clock(),
which in turn is used by the tracing mechanism for timestamps,
which leads to infinite recursion.
Disable mcount/tracing for pvclock.o.
Cc: stable@kernel.org
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
LKML-Reference: <4C9A9A3F.4040201@goop.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
earlyprintk can take and I/O port, so we need to handle this case in
the setup code too, otherwise 0x3f8 will be treated as a baud rate.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C7B05A6.4010801@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Torsten reported that there is garbage output,
after commit 8fee13a48e (x86,
setup: enable early console output from the decompressor)
It turns out we missed the offset for that case.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C7B0578.8090807@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch adds CPU type detection for dunnington processor (Family 6
/ Model 29) to be identified as core 2 family cpu type (wikipedia
source).
I tested oprofile on Intel(R) Xeon(R) CPU E7440 reporting itself as
model 29, and it runs without an issue.
Spec:
http://www.intel.com/Assets/en_US/PDF/specupdate/320336.pdf
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Robert Richter <robert.richter@amd.com>
We used to have a hypercall which reloaded the entire GDT, then we
switched to one which loaded a single entry (to match the IDT code).
Some comments were not updated, so fix them.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reported by: Eviatar Khen <eviatarkhen@gmail.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: hpet: Work around hardware stupidity
x86, build: Disable -fPIE when compiling with CONFIG_CC_STACKPROTECTOR=y
x86, cpufeature: Suppress compiler warning with gcc 3.x
x86, UV: Fix initialization of max_pnode
Lengths and types of breakpoints are encoded in a half byte
into CPU registers. However when we extract these values
and store them, we add a high half byte part to them: 0x40 to the
length and 0x80 to the type.
When that gets reloaded to the CPU registers, the high part
is masked.
While making the instruction breakpoints available for perf,
I zapped that high part on instruction breakpoint encoding
and that broke the arch -> generic translation used by ptrace
instruction breakpoints. Writing dr7 to set an inst breakpoint
was then failing.
There is no apparent reason for these high parts so we could get
rid of them altogether. That's an invasive change though so let's
do that later and for now fix the problem by restoring that inst
breakpoint high part encoding in this sole patch.
Reported-by: Kelvie Wong <kelvie@ieee.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: Will Deacon <will.deacon@arm.com>
This patch adds CPU type detection for the Intel Celeron 540, which is
part of the Core 2 family according to Wikipedia; the family and ID pair
is absent from the Volume 3B table referenced in the source code
comments. I have tested this patch on an Intel Celeron 540 machine
reporting itself as Family 6 Model 22, and OProfile runs on the machine
without issue.
Spec:
http://download.intel.com/design/mobile/SPECUPDT/317667.pdf
Signed-off-by: Patrick Simmons <linuxrocks123@netscape.net>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@kernel.org
Signed-off-by: Robert Richter <robert.richter@amd.com>
In commit d4d6715, we reopened an old hole for a 64-bit ptracer touching a
32-bit tracee in system call entry. A %rax value set via ptrace at the
entry tracing stop gets used whole as a 32-bit syscall number, while we
only check the low 32 bits for validity.
Fix it by truncating %rax back to 32 bits after syscall_trace_enter,
in addition to testing the full 64 bits as has already been added.
Reported-by: Ben Hawkes <hawkes@sota.gen.nz>
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
On 64 bits, we always, by necessity, jump through the system call
table via %rax. For 32-bit system calls, in theory the system call
number is stored in %eax, and the code was testing %eax for a valid
system call number. At one point we loaded the stored value back from
the stack to enforce zero-extension, but that was removed in checkin
d4d6715016. An actual 32-bit process
will not be able to introduce a non-zero-extended number, but it can
happen via ptrace.
Instead of re-introducing the zero-extension, test what we are
actually going to use, i.e. %rax. This only adds a handful of REX
prefixes to the code.
Reported-by: Ben Hawkes <hawkes@sota.gen.nz>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@kernel.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
compat_alloc_user_space() expects the caller to independently call
access_ok() to verify the returned area. A missing call could
introduce problems on some architectures.
This patch incorporates the access_ok() check into
compat_alloc_user_space() and also adds a sanity check on the length.
The existing compat_alloc_user_space() implementations are renamed
arch_compat_alloc_user_space() and are used as part of the
implementation of the new global function.
This patch assumes NULL will cause __get_user()/__put_user() to either
fail or access userspace on all architectures. This should be
followed by checking the return value of compat_access_user_space()
for NULL in the callers, at which time the access_ok() in the callers
can also be removed.
Reported-by: Ben Hawkes <hawkes@sota.gen.nz>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James Bottomley <jejb@parisc-linux.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <stable@kernel.org>
This more or less reverts commits 08be979 (x86: Force HPET
readback_cmp for all ATI chipsets) and 30a564be (x86, hpet: Restrict
read back to affected ATI chipsets) to the status of commit 8da854c
(x86, hpet: Erratum workaround for read after write of HPET
comparator).
The delta to commit 8da854c is mostly comments and the change from
WARN_ONCE to printk_once as we know the call path of this function
already.
This needs really in depth explanation:
First of all the HPET design is a complete failure. Having a counter
compare register which generates an interrupt on matching values
forces the software to do at least one superfluous readback of the
counter register.
While it is nice in theory to program "absolute" time events it is
practically useless because the timer runs at some absurd frequency
which can never be matched to real world units. So we are forced to
calculate a relative delta and this forces a readout of the actual
counter value, adding the delta and programming the compare
register. When the delta is small enough we run into the danger that
we program a compare value which is already in the past. Due to the
compare for equal nature of HPET we need to read back the counter
value after writing the compare rehgister (btw. this is necessary for
absolute timeouts as well) to make sure that we did not miss the timer
event. We try to work around that by setting the minimum delta to a
value which is larger than the theoretical time which elapses between
the counter readout and the compare register write, but that's only
true in theory. A NMI or SMI which hits between the readout and the
write can easily push us beyond that limit. This would result in
waiting for the next HPET timer interrupt until the 32bit wraparound
of the counter happens which takes about 306 seconds.
So we designed the next event function to look like:
match = read_cnt() + delta;
write_compare_ref(match);
return read_cnt() < match ? 0 : -ETIME;
At some point we got into trouble with certain ATI chipsets. Even the
above "safe" procedure failed. The reason was that the write to the
compare register was delayed probably for performance reasons. The
theory was that they wanted to avoid the synchronization of the write
with the HPET clock, which is understandable. So the write does not
hit the compare register directly instead it goes to some intermediate
register which is copied to the real compare register in sync with the
HPET clock. That opens another window for hitting the dreaded "wait
for a wraparound" problem.
To work around that "optimization" we added a read back of the compare
register which either enforced the update of the just written value or
just delayed the readout of the counter enough to avoid the issue. We
unfortunately never got any affirmative info from ATI/AMD about this.
One thing is sure, that we nuked the performance "optimization" that
way completely and I'm pretty sure that the result is worse than
before some HW folks came up with those.
Just for paranoia reasons I added a check whether the read back
compare register value was the same as the value we wrote right
before. That paranoia check triggered a couple of years after it was
added on an Intel ICH9 chipset. Venki added a workaround (commit
8da854c) which was reading the compare register twice when the first
check failed. We considered this to be a penalty in general and
restricted the readback (thus the wasted CPU cycles) to the known to
be affected ATI chipsets.
This turned out to be a utterly wrong decision. 2.6.35 testers
experienced massive problems and finally one of them bisected it down
to commit 30a564be which spured some further investigation.
Finally we got confirmation that the write to the compare register can
be delayed by up to two HPET clock cycles which explains the problems
nicely. All we can do about this is to go back to Venki's initial
workaround in a slightly modified version.
Just for the record I need to say, that all of this could have been
avoided if hardware designers and of course the HPET committee would
have thought about the consequences for a split second. It's out of my
comprehension why designing a working timer is so hard. There are two
ways to achieve it:
1) Use a counter wrap around aware compare_reg <= counter_reg
implementation instead of the easy compare_reg == counter_reg
Downsides:
- It needs more silicon.
- It needs a readout of the counter to apply a relative
timeout. This is necessary as the counter does not run in
any useful (and adjustable) frequency and there is no
guarantee that the counter which is used for timer events is
the same which is used for reading the actual time (and
therefor for calculating the delta)
Upsides:
- None
2) Use a simple down counter for relative timer events
Downsides:
- Absolute timeouts are not possible, which is not a problem
at all in the context of an OS and the expected
max. latencies/jitter (also see Downsides of #1)
Upsides:
- It needs less or equal silicon.
- It works ALWAYS
- It is way faster than a compare register based solution (One
write versus one write plus at least one and up to four
reads)
I would not be so grumpy about all of this, if I would not have been
ignored for many years when pointing out these flaws to various
hardware folks. I really hate timers (at least those which seem to be
designed by janitors).
Though finally we got a reasonable explanation plus a solution and I
want to thank all the folks involved in chasing it down and providing
valuable input to this.
Bisected-by: Nix <nix@esperi.org.uk>
Reported-by: Artur Skawina <art.08.09@gmail.com>
Reported-by: Damien Wyart <damien.wyart@free.fr>
Reported-by: John Drescher <drescherjm@gmail.com>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: stable@kernel.org
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The arch/x86/Makefile uses scripts/gcc-x86_$(BITS)-has-stack-protector.sh
to check if cc1 supports -fstack-protector. When -fPIE is passed to cc1,
these scripts fail causing stack protection to be disabled even when it
is available.
This fix is similar to commit c47efe5548
Reported-by: Kai Dietrich <mail@cleeus.de>
Signed-off-by: Magnus Granberg <zorry@gentoo.org>
LKML-Reference: <20100913101319.748A1148E216@opensource.dyc.edu>
Signed-off-by: Anthony G. Basile <basile@opensource.dyc.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Gcc 3.x generates a warning
arch/x86/include/asm/cpufeature.h: In function `__static_cpu_has':
arch/x86/include/asm/cpufeature.h:326: warning: asm operand 1 probably doesn't match constraints
on each file.
But static_cpu_has() for gcc 3.x does not need __static_cpu_has().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
LKML-Reference: <201008300127.o7U1RC6Z044051@www262.sakura.ne.jp>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
A real life genuine preemption leak..
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix calculation of "max_pnode" for systems where the the highest
blade has neither cpus or memory. (And, yes, although rare this
does occur).
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20100910150808.GA19802@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'kvm-updates/2.6.36' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Perform hardware_enable in CPU_STARTING callback
KVM: i8259: fix migration
KVM: fix i8259 oops when no vcpus are online
KVM: x86 emulator: fix regression with cmpxchg8b on i386 hosts
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mcheck: Avoid duplicate sysfs links/files for thresholding banks
io-mapping: Fix the address space annotations
x86: Fix the address space annotations of iomap_atomic_prot_pfn()
x86, mm: Fix CONFIG_VMSPLIT_1G and 2G_OPT trampoline
x86, hwmon: Fix unsafe smp_processor_id() in thermal_throttle_add_dev
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Try to handle unknown nmis with an enabled PMU
perf, x86: Fix handle_irq return values
perf, x86: Fix accidentally ack'ing a second event on intel perf counter
oprofile, x86: fix init_sysfs() function stub
lockup_detector: Sync touch_*_watchdog back to old semantics
tracing: Fix a race in function profile
oprofile, x86: fix init_sysfs error handling
perf_events: Fix time tracking for events with pid != -1 and cpu != -1
perf: Initialize callchains roots's childen hits
oprofile: fix crash when accessing freed task structs
Top of kvm_kpic_state structure should have the same memory layout as
kvm_pic_state since it is copied by memcpy.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
operand::val and operand::orig_val are 32-bit on i386, whereas cmpxchg8b
operands are 64-bit.
Fix by adding val64 and orig_val64 union members to struct operand, and
using them where needed.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: bus speed strings should be const
PCI hotplug: Fix build with CONFIG_ACPI unset
PCI: PCIe: Remove the port driver module exit routine
PCI: PCIe: Move PCIe PME code to the pcie directory
PCI: PCIe: Disable PCIe port services during port initialization
PCI: PCIe: Ask BIOS for control of all native services at once
ACPI/PCI: Negotiate _OSC control bits before requesting them
ACPI/PCI: Do not preserve _OSC control bits returned by a query
ACPI/PCI: Make acpi_pci_query_osc() return control bits
ACPI/PCI: Reorder checks in acpi_pci_osc_control_set()
PCI: PCIe: Introduce commad line switch for disabling port services
PCI: PCIe AER: Introduce pci_aer_available()
x86/PCI: only define pci_domain_nr if PCI and PCI_DOMAINS are set
PCI: provide stub pci_domain_nr function for !CONFIG_PCI configs
This patch fixes the sparse warnings when the return pointer of
iomap_atomic_prot_pfn() is used as an argument of iowrite32()
and friends.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
LKML-Reference: <1283633804-11749-1-git-send-email-currojerez@riseup.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When the PMU is enabled it is valid to have unhandled nmis, two
events could trigger 'simultaneously' raising two back-to-back
NMIs. If the first NMI handles both, the latter will be empty
and daze the CPU.
The solution to avoid an 'unknown nmi' massage in this case was
simply to stop the nmi handler chain when the PMU is enabled by
stating the nmi was handled. This has the drawback that a) we
can not detect unknown nmis anymore, and b) subsequent nmi
handlers are not called.
This patch addresses this. Now, we check this unknown NMI if it
could be a PMU back-to-back NMI. Otherwise we pass it and let
the kernel handle the unknown nmi.
This is a debug log:
cpu #6, nmi #32333, skip_nmi #32330, handled = 1, time = 1934364430
cpu #6, nmi #32334, skip_nmi #32330, handled = 1, time = 1934704616
cpu #6, nmi #32335, skip_nmi #32336, handled = 2, time = 1936032320
cpu #6, nmi #32336, skip_nmi #32336, handled = 0, time = 1936034139
cpu #6, nmi #32337, skip_nmi #32336, handled = 1, time = 1936120100
cpu #6, nmi #32338, skip_nmi #32336, handled = 1, time = 1936404607
cpu #6, nmi #32339, skip_nmi #32336, handled = 1, time = 1937983416
cpu #6, nmi #32340, skip_nmi #32341, handled = 2, time = 1938201032
cpu #6, nmi #32341, skip_nmi #32341, handled = 0, time = 1938202830
cpu #6, nmi #32342, skip_nmi #32341, handled = 1, time = 1938443743
cpu #6, nmi #32343, skip_nmi #32341, handled = 1, time = 1939956552
cpu #6, nmi #32344, skip_nmi #32341, handled = 1, time = 1940073224
cpu #6, nmi #32345, skip_nmi #32341, handled = 1, time = 1940485677
cpu #6, nmi #32346, skip_nmi #32347, handled = 2, time = 1941947772
cpu #6, nmi #32347, skip_nmi #32347, handled = 1, time = 1941949818
cpu #6, nmi #32348, skip_nmi #32347, handled = 0, time = 1941951591
Uhhuh. NMI received for unknown reason 00 on CPU 6.
Do you have a strange power saving mode enabled?
Dazed and confused, but trying to continue
Deltas:
nmi #32334 340186
nmi #32335 1327704
nmi #32336 1819 <<<< back-to-back nmi [1]
nmi #32337 85961
nmi #32338 284507
nmi #32339 1578809
nmi #32340 217616
nmi #32341 1798 <<<< back-to-back nmi [2]
nmi #32342 240913
nmi #32343 1512809
nmi #32344 116672
nmi #32345 412453
nmi #32346 1462095 <<<< 1st nmi (standard) handling 2 counters
nmi #32347 2046 <<<< 2nd nmi (back-to-back) handling one
counter nmi #32348 1773 <<<< 3rd nmi (back-to-back)
handling no counter! [3]
For back-to-back nmi detection there are the following rules:
The PMU nmi handler was handling more than one counter and no
counter was handled in the subsequent nmi (see [1] and [2]
above).
There is another case if there are two subsequent back-to-back
nmis [3]. The 2nd is detected as back-to-back because the first
handled more than one counter. If the second handles one counter
and the 3rd handles nothing, we drop the 3rd nmi because it
could be a back-to-back nmi.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
[ renamed nmi variable to pmu_nmi to avoid clash with .nmi in entry.S ]
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: peterz@infradead.org
Cc: gorcunov@gmail.com
Cc: fweisbec@gmail.com
Cc: ying.huang@intel.com
Cc: ming.m.lin@intel.com
Cc: eranian@google.com
LKML-Reference: <1283454469-1909-3-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
During testing of a patch to stop having the perf subsytem
swallow nmis, it was uncovered that Nehalem boxes were randomly
getting unknown nmis when using the perf tool.
Moving the ack'ing of the PMI closer to when we get the status
allows the hardware to properly re-set the PMU bit signaling
another PMI was triggered during the processing of the first
PMI. This allows the new logic for dealing with the
shortcomings of multiple PMIs to handle the extra NMI by
'eat'ing it later.
Now one can wonder why are we getting a second PMI when we
disable all the PMUs in the begining of the NMI handler to
prevent such a case, for that I do not know. But I know the fix
below helps deal with this quirk.
Tested on multiple Nehalems where the problem was occuring.
With the patch, the code now loops a second time to handle the
second PMI (whereas before it was not).
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: peterz@infradead.org
Cc: robert.richter@amd.com
Cc: gorcunov@gmail.com
Cc: fweisbec@gmail.com
Cc: ying.huang@intel.com
Cc: ming.m.lin@intel.com
Cc: eranian@google.com
LKML-Reference: <1283454469-1909-2-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The use of the return value of init_sysfs() with commit
10f0412 oprofile, x86: fix init_sysfs error handling
discovered the following build error for !CONFIG_PM:
.../linux/arch/x86/oprofile/nmi_int.c: In function ‘op_nmi_init’:
.../linux/arch/x86/oprofile/nmi_int.c:784: error: expected expression before ‘do’
make[2]: *** [arch/x86/oprofile/nmi_int.o] Error 1
make[1]: *** [arch/x86/oprofile] Error 2
This patch fixes this.
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
Signed-off-by: Robert Richter <robert.richter@amd.com>
On failure init_sysfs() might not properly free resources. The error
code of the function is not checked. And, when reinitializing the exit
function might be called twice. This patch fixes all this.
Cc: stable@kernel.org
Signed-off-by: Robert Richter <robert.richter@amd.com>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86, Pentium4: Clear the P4_CCCR_FORCE_OVF flag
tracing/trace_stack: Fix stack trace on ppc64
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, tsc, sched: Recompute cyc2ns_offset's during resume from sleep states
sched: Fix rq->clock synchronization when migrating tasks
If on Pentium4 CPUs the FORCE_OVF flag is set then an NMI happens
on every event, which can generate a flood of NMIs. Clear it.
Reported-by: Vince Weaver <vweaver1@eecs.utk.edu>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
rc2 kernel crashes when booting second cpu on this CONFIG_VMSPLIT_2G_OPT
laptop: whereas cloning from kernel to low mappings pgd range does need
to limit by both KERNEL_PGD_PTRS and KERNEL_PGD_BOUNDARY, cloning kernel
pgd range itself must not be limited by the smaller KERNEL_PGD_BOUNDARY.
Signed-off-by: Hugh Dickins <hughd@google.com>
LKML-Reference: <alpine.LSU.2.00.1008242235120.2515@sister.anvils>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-upstream/pvhvm' of git://xenbits.xensource.com/people/ianc/linux-2.6:
xen: pvhvm: make it clearer that XEN_UNPLUG_* define bits in a bitfield
xen: pvhvm: rename xen_emul_unplug=ignore to =unnnecessary
xen: pvhvm: allow user to request no emulated device unplug
It is not immediately clear what this option causes to become
ignored. The actual meaning is that it is not necessary to unplug the
emulated devices to safely use the PV ones, even if the platform does
not support the unplug protocol. (pressumably the user will only add
this option if they have ensured that their domain configuration is
safe).
I think xen_emul_unplug=unnecessary better captures this.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Stefano Stabellini <Stefano.Stabellini@eu.citrix.com>
this allows the user to disable pvhvm and revert to emulated devices
in case of a system misconfiguration (e.g. initramfs with only
emulated drivers in it).
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Stefano Stabellini <Stefano.Stabellini@eu.citrix.com>
* 'kvm-updates/2.6.36' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PIT: free irq source id in handling error path
KVM: destroy workqueue on kvm_create_pit() failures
KVM: fix poison overwritten caused by using wrong xstate size
The "Configure" word tends to make user believe they have to say 'yes'
to be able to choose the number of procs/nodes. "Enable" should be
unambiguous enough.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix BUG: using smp_processor_id() in preemptible thermal_throttle_add_dev.
We know the cpu number when calling thermal_throttle_add_dev, so we can
remove smp_processor_id call in thermal_throttle_add_dev by supplying
the cpu number as argument.
This should resolve kernel bugzilla 16615/16629.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
LKML-Reference: <20100820073634.GB5209@swordfish.minsk.epam.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Joerg Roedel <Joerg.Roedel@amd.com>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
TSC's get reset after suspend/resume (even on cpu's with invariant TSC
which runs at a constant rate across ACPI P-, C- and T-states). And in
some systems BIOS seem to reinit TSC to arbitrary large value (still
sync'd across cpu's) during resume.
This leads to a scenario of scheduler rq->clock (sched_clock_cpu()) less
than rq->age_stamp (introduced in 2.6.32). This leads to a big value
returned by scale_rt_power() and the resulting big group power set by the
update_group_power() is causing improper load balancing between busy and
idle cpu's after suspend/resume.
This resulted in multi-threaded workloads (like kernel-compilation) go
slower after suspend/resume cycle on core i5 laptops.
Fix this by recomputing cyc2ns_offset's during resume, so that
sched_clock() continues from the point where it was left off during
suspend.
Reported-by: Florian Pritz <flo@xssn.at>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: <stable@kernel.org> # [v2.6.32+]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1282262618.2675.24.camel@sbsiddha-MOBL3.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix a boot crash when apic=debug is used and the APIC is
not properly initialized.
This issue appears during Xen Dom0 kernel boot but the
fix is generic and the crash could occur on real hardware
as well.
Signed-off-by: Daniel Kiper <dkiper@net-space.pl>
Cc: xen-devel@lists.xensource.com
Cc: konrad.wilk@oracle.com
Cc: jeremy@goop.org
Cc: <stable@kernel.org> # .35.x, .34.x, .33.x, .32.x
LKML-Reference: <20100819224616.GB9967@router-fw-old.local.net-space.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When testing cpu hotplug code on 32-bit we kept hitting the "CPU%d:
Stuck ??" message due to multiple cores concurrently accessing the
cpu_callin_mask, among others.
Since these codepaths are not protected from concurrent access due to
the fact that there's no sane reason for making an already complex
code unnecessarily more complex - we hit the issue only when insanely
switching cores off- and online - serialize hotplugging cores on the
sysfs level and be done with it.
[ v2.1: fix !HOTPLUG_CPU build ]
Cc: <stable@kernel.org>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20100819181029.GC17171@aftab>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Fix dummy inline stubs for trampoline-related functions when no
trampolines exist (until we get rid of the no-trampoline case
entirely.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <4C6C294D.3030404@zytor.com>
This patch fixes machine crashes which occur when heavily exercising the
CPU hotplug codepaths on a 32-bit kernel. These crashes are caused by
AMD Erratum 383 and result in a fatal machine check exception. Here's
the scenario:
1. On 32-bit, the swapper_pg_dir page table is used as the initial page
table for booting a secondary CPU.
2. To make this work, swapper_pg_dir needs a direct mapping of physical
memory in it (the low mappings). By adding those low, large page (2M)
mappings (PAE kernel), we create the necessary conditions for Erratum
383 to occur.
3. Other CPUs which do not participate in the off- and onlining game may
use swapper_pg_dir while the low mappings are present (when leave_mm is
called). For all steps below, the CPU referred to is a CPU that is using
swapper_pg_dir, and not the CPU which is being onlined.
4. The presence of the low mappings in swapper_pg_dir can result
in TLB entries for addresses below __PAGE_OFFSET to be established
speculatively. These TLB entries are marked global and large.
5. When the CPU with such TLB entry switches to another page table, this
TLB entry remains because it is global.
6. The process then generates an access to an address covered by the
above TLB entry but there is a permission mismatch - the TLB entry
covers a large global page not accessible to userspace.
7. Due to this permission mismatch a new 4kb, user TLB entry gets
established. Further, Erratum 383 provides for a small window of time
where both TLB entries are present. This results in an uncorrectable
machine check exception signalling a TLB multimatch which panics the
machine.
There are two ways to fix this issue:
1. Always do a global TLB flush when a new cr3 is loaded and the
old page table was swapper_pg_dir. I consider this a hack hard
to understand and with performance implications
2. Do not use swapper_pg_dir to boot secondary CPUs like 64-bit
does.
This patch implements solution 2. It introduces a trampoline_pg_dir
which has the same layout as swapper_pg_dir with low_mappings. This page
table is used as the initial page table of the booting CPU. Later in the
bringup process, it switches to swapper_pg_dir and does a global TLB
flush. This fixes the crashes in our test cases.
-v2: switch to swapper_pg_dir right after entering start_secondary() so
that we are able to access percpu data which might not be mapped in the
trampoline page table.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
LKML-Reference: <20100816123833.GB28147@aftab>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
A bug in the family-model-stepping matching code caused the presence of
errata to go undetected when OSVW was not used. This causes hangs on
some K8 systems because the E400 workaround is not enabled.
Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
LKML-Reference: <1282141190-930137-1-git-send-email-hans.rosenfeld@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Fix the Errata AAK100/AAP53/BD53 workaround, the officialy documented
workaround we implemented in:
11164cd: perf, x86: Add Nehelem PMU programming errata workaround
doesn't actually work fully and causes a stuck PMU state
under load and non-functioning perf profiling.
A functional workaround was found by trial & error.
Affects all Nehalem-class Intel PMUs.
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1281073148.2125.63.camel@ymzhang.sh.intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <stable@kernel.org> # .35.x
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
vt,console,kdb: preserve console_blanked while in kdb
vt: fix regression warnings from KMS merge
arm,kgdb: fix GDB_MAX_REGS no longer used
kgdb: add missing __percpu markup in arch/x86/kernel/kgdb.c
kdb: fix compile error without CONFIG_KALLSYMS
Make do_execve() take a const filename pointer so that kernel_execve() compiles
correctly on ARM:
arch/arm/kernel/sys_arm.c:88: warning: passing argument 1 of 'do_execve' discards qualifiers from pointer target type
This also requires the argv and envp arguments to be consted twice, once for
the pointer array and once for the strings the array points to. This is
because do_execve() passes a pointer to the filename (now const) to
copy_strings_kernel(). A simpler alternative would be to cast the filename
pointer in do_execve() when it's passed to copy_strings_kernel().
do_execve() may not change any of the strings it is passed as part of the argv
or envp lists as they are some of them in .rodata, so marking these strings as
const should be fine.
Further kernel_execve() and sys_execve() need to be changed to match.
This has been test built on x86_64, frv, arm and mips.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Otherwise we'll duplicate definitions with the pci.h stubs.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
breakinfo->pev is a pointer to percpu pointer but was missing __percpu markup.
Add it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
gcc-4.6: ACPI: fix unused but set variables in ACPI
ACPI thermal: make procfs I/F depend on CONFIG_ACPI_PROCFS
ACPI video: make procfs I/F depend on CONFIG_ACPI_PROCFS
ACPI processor: remove deprecated ACPI procfs I/F
ACPI power_resource: remove unused procfs I/F
ACPI: remove deprecated ACPI procfs I/F
ACPI: introduce drivers/acpi/sysfs.c
ACPI: introduce module parameter acpi.aml_debug_output
ACPI: introduce drivers/acpi/debugfs.c
ACPI, APEI, ERST debug support
ACPI, APEI, Manage GHES as platform devices
ACPI, APEI, Rename CPER and GHES severity constants
ACPI, APEI, Fix a typo of error path of apei_resources_request
ACPI / ACPICA: Fix reference counting problems with GPE handlers
ACPI: Add the check of ADR flag in course of finding ACPI handle for PCI device
ACPI / Sleep: Drop acpi_suspend_finish()
ACPI / Sleep: Consolidate suspend and hibernation routines
ACPI / Wakeup: Simplify enabling of wakeup devices
ACPI / Sleep: Rework enabling wakeup devices
ACPI / Sleep: Free NVS copy if suspending of devices fails
Fixed up totally buggered "ACPI: fix unused but set variables in ACPI"
patch that doesn't even compile in the merge.
Thanks to Sedat Dilek <sedat.dilek@googlemail.com> for noticing the
breakage before I even pulled. And a big "Grrr.." at Len for not even
bothering to compile the tree before asking me to pull.
fpu.state is allocated from task_xstate_cachep, the size of task_xstate_cachep
is xstate_size. xstate_size is set from cpuid instruction, which is often
smaller than sizeof(struct xsave_struct). kvm is using sizeof(struct xsave_struct)
to fill in/out fpu.state.xsave, as what we allocated for fpu.state is
xstate_size, kernel will write out of memory and caused poison/redzone/padding
overwritten warnings.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Reviewed-by: Sheng Yang <sheng@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Sheng Yang <sheng@linux.intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Mark arguments to certain system calls as being const where they should be but
aren't. The list includes:
(*) The filename arguments of various stat syscalls, execve(), various utimes
syscalls and some mount syscalls.
(*) The filename arguments of some syscall helpers relating to the above.
(*) The buffer argument of various write syscalls.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
perf: Add back list_head data types
perf ui hist browser: Fixup key bindings
perf ui browser: Add ui_browser__show counterpart: __hide
perf annotate: Cycle thru sorted lines with samples
perf ui: Make SPACE work as PGDN in all browsers
perf annotate: Sort by hottest lines in the TUI
perf ui: Complete the breakdown of util/newt.c
perf ui: Move hists browser to util/ui/browsers/
perf symbols: Ignore mapping symbols on ARM
perf ui: Move map browser to util/ui/browsers/
perf ui: Move annotate browser to util/ui/browsers/
perf ui: Move ui_progress routines to separate file in util/ui/
perf ui: Move ui_helpline routines to separate file in util/ui/
perf ui: Shorten ui_browser member names
perf, x86: P4 PMU -- update nmi irq statistics and unmask lvt entry properly
perf ui: Start breaking down newt.c into multiple files
perf tui: Introduce list_head based generic ui_browser refresh routine
perf probe: Fix memory leaks in add_perf_probe_events
perf probe: Fix to copy the type for raw parameters
perf report: Speed up exit path
...
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Initialize BAU MMRs only on hubs with cpus
x86, UV: Modularize BAU send and wait
x86, UV: BAU broadcast to the local hub
x86, UV: Correct BAU regular message type
x86, UV: Remove BAU check for stay-busy
x86, UV: Correct BAU discovery of hubs and sockets
x86, UV: Correct BAU software acknowledge
x86, UV: BAU structure rearranging
x86, UV: Shorten access to BAU statistics structure
x86, UV: Disable BAU on network congestion
x86, UV: BAU tunables into a debugfs file
x86, UV: Calculate BAU destination timeout
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, asm: Use a lower case name for the end macro in atomic64_386_32.S
x86, asm: Refactor atomic64_386_32.S to support old binutils and be cleaner
x86: Document __phys_reloc_hide() usage in __pa_symbol()
x86, apic: Map the local apic when parsing the MP table.
It's wrong for several reasons, but the most direct one is that the
fault may be for the stack accesses to set up a previous SIGBUS. When
we have a kernel exception, the kernel exception handler does all the
fixups, not some user-level signal handler.
Even apart from the nested SIGBUS issue, it's also wrong to give out
kernel fault addresses in the signal handler info block, or to send a
SIGBUS when a system call already returns EFAULT.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
acpi_perf_data is a percpu pointer but was missing __percpu markup.
Add it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dave Jones <davej@redhat.com>
This replaces Version 1 of this patch, which broke the build when
CONFIG_KEXEC and CONFIG_CRASH_DUMP were configured off. In that case
the storage for the 'in_crash_kexec' flag was never built.
This version defines that flag as 0 if CONFIG_KEXEC is not set.
The patch is tested with all combinations of those two options.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <E1OiZcw-0001Hb-2g@eag09.americas.sgi.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The current computation, introduced with f12a15be63, of FSEC_PER_SEC using
the multiplication of (FSEC_PER_NSEC * NSEC_PER_SEC) is performed only
with 32bit integers on small machines, resulting in an overflow and a
*very* short intervals being programmed. An interrupt storm follows.
Note that we also have to specify FSEC_PER_SEC as being long long to
overcome the same limitations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pcc_cpu_info is a percpu pointer but was missing __percpu markup.
Add it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'stable/xen-swiotlb-0.8.6' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
x86: Detect whether we should use Xen SWIOTLB.
pci-swiotlb-xen: Add glue code to setup dma_ops utilizing xen_swiotlb_* functions.
swiotlb-xen: SWIOTLB library for Xen PV guest with PCI passthrough.
xen/mmu: inhibit vmap aliases rather than trying to clear them out
vmap: add flag to allow lazy unmap to be disabled at runtime
xen: Add xen_create_contiguous_region
xen: Rename the balloon lock
xen: Allow unprivileged Xen domains to create iomap pages
xen: use _PAGE_IOMAP in ioremap to do machine mappings
Fix up trivial conflicts (adding both xen swiotlb and xen pci platform
driver setup close to each other) in drivers/xen/{Kconfig,Makefile} and
include/xen/xen-ops.h
Use a lowercase name for the end macro, which somehow fixes a binutils 2.16
problem.
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
LKML-Reference: <tip-30246557a06bb20618bed906a06d1e1e0faa8bb4@git.kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The old code didn't work on binutils 2.12 because setting a symbol to
a register apparently requires a fairly recent version.
This commit refactors the code to use the C preprocessor instead, and
in the process makes the whole code a bit easier to understand.
The object code produced is unchanged as expected.
This fixes kernel bugzilla 16506.
Reported-by: Dieter Stussy <kd6lvw+software@kd6lvw.ampr.org>
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org> 2.6.35
LKML-Reference: <tip-*@git.kernel.org>
Architectures implement dma_is_consistent() in different ways (some
misinterpret the definition of API in DMA-API.txt). So it hasn't been so
useful for drivers. We have only one user of the API in tree. Unlikely
out-of-tree drivers use the API.
Even if we fix dma_is_consistent() in some architectures, it doesn't look
useful at all. It was invented long ago for some old systems that can't
allocate coherent memory at all. It's better to export only APIs that are
definitely necessary for drivers.
Let's remove this API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
defines it as ARCH_DMA_MINALIGN (formally ARCH_KMALLOC_MINALIGN). So we
can unify dma_get_cache_alignment implementations.
Note that some architectures implement dma_get_cache_alignment wrongly.
dma_get_cache_alignment() should return the minimum DMA alignment. So
fully-coherent architectures should return 1. This patch also fixes this
issue.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Until all supported versions of gcc recognize
-fno-strict-overflow, we should keep the RELOC_HIDE() magic in
__pa_symbol(). Comment it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
LKML-Reference: <1281508661-29507-1-git-send-email-namhyung@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As pointed out by Jiri Slaby: when I resolved the the 32-bit x85 system
call entry tables for prlimit (due to the conflict with fanotify), I
forgot to add the numbering in comments that we do for every fifth entry.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
* 'writable_limits' of git://decibel.fi.muni.cz/~xslaby/linux:
unistd: add __NR_prlimit64 syscall numbers
rlimits: implement prlimit64 syscall
rlimits: switch more rlimit syscalls to do_prlimit
rlimits: redo do_setrlimit to more generic do_prlimit
rlimits: add rlimit64 structure
rlimits: do security check under task_lock
rlimits: allow setrlimit to non-current tasks
rlimits: split sys_setrlimit
rlimits: selinux, do rlimits changes under task_lock
rlimits: make sure ->rlim_max never grows in sys_setrlimit
rlimits: add task_struct to update_rlimit_cpu
rlimits: security, add task_struct to setrlimit
Fix up various system call number conflicts. We not only added fanotify
system calls in the meantime, but asm-generic/unistd.h added a wait4
along with a range of reserved per-architecture system calls.
* 'for-linus' of git://git.infradead.org/users/eparis/notify: (132 commits)
fanotify: use both marks when possible
fsnotify: pass both the vfsmount mark and inode mark
fsnotify: walk the inode and vfsmount lists simultaneously
fsnotify: rework ignored mark flushing
fsnotify: remove global fsnotify groups lists
fsnotify: remove group->mask
fsnotify: remove the global masks
fsnotify: cleanup should_send_event
fanotify: use the mark in handler functions
audit: use the mark in handler functions
dnotify: use the mark in handler functions
inotify: use the mark in handler functions
fsnotify: send fsnotify_mark to groups in event handling functions
fsnotify: Exchange list heads instead of moving elements
fsnotify: srcu to protect read side of inode and vfsmount locks
fsnotify: use an explicit flag to indicate fsnotify_destroy_mark has been called
fsnotify: use _rcu functions for mark list traversal
fsnotify: place marks on object in order of group memory address
vfs/fsnotify: fsnotify_close can delay the final work in fput
fsnotify: store struct file not struct path
...
Fix up trivial delete/modify conflict in fs/notify/inotify/inotify.c.
Workqueues are now initialized as part of the early_initcall(). So they
are available for use during cold boot process aswell.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No real bugs, just some dead code and some fixups.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kunmap_atomic() is currently at level -4 on Rusty's "Hard To Misuse"
list[1] ("Follow common convention and you'll get it wrong"), except in
some architectures when CONFIG_DEBUG_HIGHMEM is set[2][3].
kunmap() takes a pointer to a struct page; kunmap_atomic(), however, takes
takes a pointer to within the page itself. This seems to once in a while
trip people up (the convention they are following is the one from
kunmap()).
Make it much harder to misuse, by moving it to level 9 on Rusty's list[4]
("The compiler/linker won't let you get it wrong"). This is done by
refusing to build if the type of its first argument is a pointer to a
struct page.
The real kunmap_atomic() is renamed to kunmap_atomic_notypecheck()
(which is what you would call in case for some strange reason calling it
with a pointer to a struct page is not incorrect in your code).
The previous version of this patch was compile tested on x86-64.
[1] http://ozlabs.org/~rusty/index.cgi/tech/2008-04-01.html
[2] In these cases, it is at level 5, "Do it right or it will always
break at runtime."
[3] At least mips and powerpc look very similar, and sparc also seems to
share a common ancestor with both; there seems to be quite some
degree of copy-and-paste coding here. The include/asm/highmem.h file
for these three archs mention x86 CPUs at its top.
[4] http://ozlabs.org/~rusty/index.cgi/tech/2008-03-30.html
[5] As an aside, could someone tell me why mn10300 uses unsigned long as
the first parameter of kunmap_atomic() instead of void *?
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Cc: Russell King <linux@arm.linux.org.uk> (arch/arm)
Cc: Ralf Baechle <ralf@linux-mips.org> (arch/mips)
Cc: David Howells <dhowells@redhat.com> (arch/frv, arch/mn10300)
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com> (arch/mn10300)
Cc: Kyle McMartin <kyle@mcmartin.ca> (arch/parisc)
Cc: Helge Deller <deller@gmx.de> (arch/parisc)
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> (arch/parisc)
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> (arch/powerpc)
Cc: Paul Mackerras <paulus@samba.org> (arch/powerpc)
Cc: "David S. Miller" <davem@davemloft.net> (arch/sparc)
Cc: Thomas Gleixner <tglx@linutronix.de> (arch/x86)
Cc: Ingo Molnar <mingo@redhat.com> (arch/x86)
Cc: "H. Peter Anvin" <hpa@zytor.com> (arch/x86)
Cc: Arnd Bergmann <arnd@arndb.de> (include/asm-generic)
Cc: Rusty Russell <rusty@rustcorp.com.au> ("Hard To Misuse" list)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case if last active performance counter is not overflowed at
moment of NMI being triggered by another counter, the irq
statistics may miss an update stage. As a more serious
consequence -- apic quirk may not be triggered so apic lvt entry
stay masked.
Tested-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20100805150917.GA6311@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The abbreviation of severity should be SEV instead of SER, so the CPER
severity constants are renamed accordingly. GHES severity constants
are renamed in the same way too.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (55 commits)
workqueue: mark init_workqueues() as early_initcall()
workqueue: explain for_each_*cwq_cpu() iterators
fscache: fix build on !CONFIG_SYSCTL
slow-work: kill it
gfs2: use workqueue instead of slow-work
drm: use workqueue instead of slow-work
cifs: use workqueue instead of slow-work
fscache: drop references to slow-work
fscache: convert operation to use workqueue instead of slow-work
fscache: convert object to use workqueue instead of slow-work
workqueue: fix how cpu number is stored in work->data
workqueue: fix mayday_mask handling on UP
workqueue: fix build problem on !CONFIG_SMP
workqueue: fix locking in retry path of maybe_create_worker()
async: use workqueue for worker pool
workqueue: remove WQ_SINGLE_CPU and use WQ_UNBOUND instead
workqueue: implement unbound workqueue
workqueue: prepare for WQ_UNBOUND implementation
libata: take advantage of cmwq and remove concurrency limitations
workqueue: fix worker management invocation without pending works
...
Fixed up conflicts in fs/cifs/* as per Tejun. Other trivial conflicts in
include/linux/workqueue.h, kernel/trace/Kconfig and kernel/workqueue.c
* 'x86-xsave-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, xsave: Make xstate_enable_boot_cpu() __init, protect on CPU 0
x86, xsave: Add __init attribute to setup_xstate_features()
x86, xsave: Make init_xstate_buf static
x86, xsave: Check cpuid level for XSTATE_CPUID (0x0d)
x86, xsave: Introduce xstate enable functions
x86, xsave: Separate fpu and xsave initialization
x86, xsave: Move boot cpu initialization to xsave_init()
x86, xsave: 32/64 bit boot cpu check unification in initialization
x86, xsave: Do not include asm/i387.h in asm/xsave.h
x86, xsave: Use xsaveopt in context-switch path when supported
x86, xsave: Sync xsave memory layout with its header for user handling
x86, xsave: Track the offset, size of state in the xsave layout
* 'x86-olpc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, olpc: Constify an olpc_ofw() arg
x86, olpc: Use pr_debug() for EC commands
x86, olpc: Add comment about implicit optimization barrier
x86, olpc: Add support for calling into OpenFirmware
* 'x86-alternatives-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, alternatives: BUG on encountering an invalid CPU feature number
x86, alternatives: Fix one more open-coded 8-bit alternative number
x86, alternatives: Use 16-bit numbers for cpufeature index
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Clean up arch/x86/kernel/cpu/mtrr/cleanup.c: use ";" not "," to terminate statements
* 'x86-vmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, vmware: Preset lpj values when on VMware.
* 'x86-mtrr-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mtrr: Use stop machine context to rendezvous all the cpu's
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/apic/es7000_32: Remove unused variable
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Avoid unnecessary __clear_user() and xrstor in signal handling
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, vdso: Unmap vdso pages
* 'timers-timekeeping-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
um: Fix read_persistent_clock fallout
kgdb: Do not access xtime directly
powerpc: Clean up obsolete code relating to decrementer and timebase
powerpc: Rework VDSO gettimeofday to prevent time going backwards
clocksource: Add __clocksource_updatefreq_hz/khz methods
x86: Convert common clocksources to use clocksource_register_hz/khz
timekeeping: Make xtime and wall_to_monotonic static
hrtimer: Cleanup direct access to wall_to_monotonic
um: Convert to use read_persistent_clock
timkeeping: Fix update_vsyscall to provide wall_to_monotonic offset
powerpc: Cleanup xtime usage
powerpc: Simplify update_vsyscall
time: Kill off CONFIG_GENERIC_TIME
time: Implement timespec_add
x86: Fix vtime/file timestamp inconsistencies
Trivial conflicts in Documentation/feature-removal-schedule.txt
Much less trivial conflicts in arch/powerpc/kernel/time.c resolved as
per Thomas' earlier merge commit 47916be4e2 ("Merge branch
'powerpc.cherry-picks' into timers/clocksource")
KVM ended up having to put a pretty ugly wrapper around set_64bit()
in order to get the type right. Now set_64bit() takes the expected
u64 type, and this wrapper can be cleaned up.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Avi Kivity <avi@redhat.com>
LKML-Reference: <4C5C4E7A.8040603@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (30 commits)
PCI: update for owner removal from struct device_attribute
PCI: Fix warnings when CONFIG_DMI unset
PCI: Do not run NVidia quirks related to MSI with MSI disabled
x86/PCI: use for_each_pci_dev()
PCI: use for_each_pci_dev()
PCI: MSI: Restore read_msi_msg_desc(); add get_cached_msi_msg_desc()
PCI: export SMBIOS provided firmware instance and label to sysfs
PCI: Allow read/write access to sysfs I/O port resources
x86/PCI: use host bridge _CRS info on ASRock ALiveSATA2-GLAN
PCI: remove unused HAVE_ARCH_PCI_SET_DMA_MAX_SEGMENT_{SIZE|BOUNDARY}
PCI: disable mmio during bar sizing
PCI: MSI: Remove unsafe and unnecessary hardware access
PCI: Default PCIe ASPM control to on and require !EMBEDDED to disable
PCI: kernel oops on access to pci proc file while hot-removal
PCI: pci-sysfs: remove casts from void*
ACPI: Disable ASPM if the platform won't provide _OSC control for PCIe
PCI hotplug: make sure child bridges are enabled at hotplug time
PCI hotplug: shpchp: Removed check for hotplug of display devices
PCI hotplug: pciehp: Fixed return value sign for pciehp_unconfigure_device
PCI: Don't enable aspm before drivers have had a chance to veto it
...
* 'x86-rwsem-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, rwsem: Minor cleanups
x86, rwsem: Stay on fast path when count > 0 in __up_write()
* 'x86-gcc46-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, gcc-4.6: Fix set but not read variables
x86, gcc-4.6: Avoid unused by set variables in rdmsr
* 'x86-setup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, setup: move isdigit.h to ctype.h, header files on top.
x86, setup: enable early console output from the decompressor
x86, setup: reorganize the early console setup
x86, setup: Allow global variables and functions in the decompressor
x86, setup: Only set early_serial_base after port is initialized
x86, setup: Make the setup code also accept console=uart8250
x86, setup: Early-boot serial I/O support
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Ioremap: fix wrong physical address handling in PAT code
x86, tlb: Clean up and correct used type
x86, iomap: Fix wrong page aligned size calculation in ioremapping code
x86, mm: Create symbolic index into address_markers array
x86, ioremap: Fix normal ram range check
x86, ioremap: Fix incorrect physical address handling in PAE mode
x86-64, mm: Initialize VDSO earlier on 64 bits
x86, kmmio/mmiotrace: Fix double free of kmmio_fault_pages
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, vdso: Don't quote $nm in the script for checking vdso references
x86, vdso: Error out if the vdso contains external references
* 'x86-mrst-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mrst: make mrst_timer_options an enum
x86, mrst: make mrst_identify_cpu() an inline returning enum
x86, mrst: add more timer config options
x86, mrst: add cpu type detection
x86: detect scattered cpuid features earlier
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (162 commits)
tracing/kprobes: unregister_trace_probe needs to be called under mutex
perf: expose event__process function
perf events: Fix mmap offset determination
perf, powerpc: fsl_emb: Restore setting perf_sample_data.period
perf, powerpc: Convert the FSL driver to use local64_t
perf tools: Don't keep unreferenced maps when unmaps are detected
perf session: Invalidate last_match when removing threads from rb_tree
perf session: Free the ref_reloc_sym memory at the right place
x86,mmiotrace: Add support for tracing STOS instruction
perf, sched migration: Librarize task states and event headers helpers
perf, sched migration: Librarize the GUI class
perf, sched migration: Make the GUI class client agnostic
perf, sched migration: Make it vertically scrollable
perf, sched migration: Parameterize cpu height and spacing
perf, sched migration: Fix key bindings
perf, sched migration: Ignore unhandled task states
perf, sched migration: Handle ignored migrate out events
perf: New migration tool overview
tracing: Drop cpparg() macro
perf: Use tracepoint_synchronize_unregister() to flush any pending tracepoint call
...
Fix up trivial conflicts in Makefile and drivers/cpufreq/cpufreq.c
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
Revert "net: Make accesses to ->br_port safe for sparse RCU"
mce: convert to rcu_dereference_index_check()
net: Make accesses to ->br_port safe for sparse RCU
vfs: add fs.h to define struct file
lockdep: Add an in_workqueue_context() lockdep-based test function
rcu: add __rcu API for later sparse checking
rcu: add an rcu_dereference_index_check()
tree/tiny rcu: Add debug RCU head objects
mm: remove all rcu head initializations
fs: remove all rcu head initializations, except on_stack initializations
powerpc: remove all rcu head initializations
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Export cache-coherency capability
iommu-api: Extension to check for interrupt remapping
x86/amd-iommu: Use for_each_pci_dev()
This fixes a regression in 2.6.35 from 2.6.34, that is
present for select models of Intel cpus when people are
using an MP table.
The commit cf7500c0ea
"x86, ioapic: In mpparse use mp_register_ioapic" started
calling mp_register_ioapic from MP_ioapic_info. An extremely
simple change that was obviously correct. Unfortunately
mp_register_ioapic did just a little more than the previous
hand crafted code and so we gained this call path.
The problem call path is:
MP_ioapic_info()
mp_register_ioapic()
io_apic_unique_id()
io_apic_get_unique_id()
get_physical_broadcast()
modern_apic()
lapic_get_version()
apic_read(APIC_LVR)
Which turned out to be a problem because the local apic
was not mapped, at that point, unlike the similar point
in the ACPI parsing code.
This problem is fixed by mapping the local apic when
parsing the mptable as soon as we reasonably can.
Looking at the number of places we setup the fixmap for
the local apic, I see some serious simplification opportunities.
For the moment except for not duplicating the setting up of the
fixmap in init_apic_mappings, I have not acted on them.
The regression from 2.6.34 is tracked in bug
https://bugzilla.kernel.org/show_bug.cgi?id=16173
Cc: <stable@kernel.org> 2.6.35
Reported-by: David Hill <hilld@binarystorm.net>
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@sophos.com>
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@sophos.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <m1eiee86jg.fsf_-_@fess.ebiederm.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
debug_core,kdb: fix crash when arch does not have single step
kgdb,x86: use macro HBP_NUM to replace magic number 4
kgdb,mips: remove unused kgdb_cpu_doing_single_step operations
mm,kdb,kgdb: Add a debug reference for the kdb kmap usage
KGDB: Remove set but unused newPC
ftrace,kdb: Allow dumping a specific cpu's buffer with ftdump
ftrace,kdb: Extend kdb to be able to dump the ftrace buffer
kgdb,powerpc: Replace hardcoded offset by BREAK_INSTR_SIZE
arm,kgdb: Add ability to trap into debugger on notify_die
gdbstub: do not directly use dbg_reg_def[] in gdb_cmd_reg_set()
gdbstub: Implement gdbserial 'p' and 'P' packets
kgdb,arm: Individual register get/set for arm
kgdb,mips: Individual register get/set for mips
kgdb,x86: Individual register get/set for x86
kgdb,kdb: individual register set and and get API
gdbstub: Optimize kgdb's "thread:" response for the gdb serial protocol
kgdb: remove custom hex_to_bin()implementation
* 'upstream/xen' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen: (23 commits)
xen/panic: use xen_reboot and fix smp_send_stop
Xen: register panic notifier to take crashes of xen guests on panic
xen: support large numbers of CPUs with vcpu info placement
xen: drop xen_sched_clock in favour of using plain wallclock time
pvops: do not notify callers from register_xenstore_notifier
Introduce CONFIG_XEN_PVHVM compile option
blkfront: do not create a PV cdrom device if xen_hvm_guest
support multiple .discard.* sections to avoid section type conflicts
xen/pvhvm: fix build problem when !CONFIG_XEN
xenfs: enable for HVM domains too
x86: Call HVMOP_pagetable_dying on exit_mmap.
x86: Unplug emulated disks and nics.
x86: Use xen_vcpuop_clockevent, xen_clocksource and xen wallclock.
implement O_NONBLOCK for /proc/xen/xenbus
xen: Fix find_unbound_irq in presence of ioapic irqs.
xen: Add suspend/resume support for PV on HVM guests.
xen: Xen PCI platform device driver.
x86/xen: event channels delivery on HVM.
x86: early PV on HVM features initialization.
xen: Add support for HVM hypercalls.
...
Use the macros provided by the HW breakpoint API.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Implement the ability to individually get and set registers for kdb
and kgdb for x86.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
CC: Ingo Molnar <mingo@redhat.com>
CC: x86@kernel.org
Newer Intel processors identifying themselves as model 30 are not recognized by
oprofile.
<cpuinfo snippet>
model : 30
model name : Intel(R) Xeon(R) CPU X3470 @ 2.93GHz
</cpuinfo snippet>
Running oprofile on these machines gives the following:
+ opcontrol --init
+ opcontrol --list-events
oprofile: available events for CPU type "Intel Architectural Perfmon"
See Intel 64 and IA-32 Architectures Software Developer's Manual
Volume 3B (Document 253669) Chapter 18 for architectural perfmon events
This is a limited set of fallback events because oprofile doesn't know your CPU
CPU_CLK_UNHALTED: (counter: all)
Clock cycles when not halted (min count: 6000)
INST_RETIRED: (counter: all)
number of instructions retired (min count: 6000)
LLC_MISSES: (counter: all)
Last level cache demand requests from this core that missed the LLC
(min count: 6000)
Unit masks (default 0x41)
----------
0x41: No unit mask
LLC_REFS: (counter: all)
Last level cache demand requests from this core (min count: 6000)
Unit masks (default 0x4f)
----------
0x4f: No unit mask
BR_MISS_PRED_RETIRED: (counter: all)
number of mispredicted branches retired (precise) (min count: 500)
+ opcontrol --shutdown
Tested using oprofile 0.9.6.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
* upstream/pvhvm:
Introduce CONFIG_XEN_PVHVM compile option
blkfront: do not create a PV cdrom device if xen_hvm_guest
support multiple .discard.* sections to avoid section type conflicts
xen/pvhvm: fix build problem when !CONFIG_XEN
xenfs: enable for HVM domains too
x86: Call HVMOP_pagetable_dying on exit_mmap.
x86: Unplug emulated disks and nics.
x86: Use xen_vcpuop_clockevent, xen_clocksource and xen wallclock.
xen: Fix find_unbound_irq in presence of ioapic irqs.
xen: Add suspend/resume support for PV on HVM guests.
xen: Xen PCI platform device driver.
x86/xen: event channels delivery on HVM.
x86: early PV on HVM features initialization.
xen: Add support for HVM hypercalls.
Conflicts:
arch/x86/xen/enlighten.c
arch/x86/xen/time.c
* upstream/core:
xen/panic: use xen_reboot and fix smp_send_stop
Xen: register panic notifier to take crashes of xen guests on panic
xen: support large numbers of CPUs with vcpu info placement
xen: drop xen_sched_clock in favour of using plain wallclock time
pvops: do not notify callers from register_xenstore_notifier
xen: make sure pages are really part of domain before freeing
xen: release unused free memory
Offline vcpu when using stop_self.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Register a panic notifier so that when the guest crashes it can shut
down the domain and indicate it was a crash to the host.
Signed-off-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
When vcpu info placement is supported, we're not limited to MAX_VIRT_CPUS
vcpus. However, if it isn't supported, then ignore any excess vcpus.
Signed-off-by: Mukesh Rathor <mukesh.rathor@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
xen_sched_clock only counts unstolen time. In principle this should
be useful to the Linux scheduler so that it knows how much time a process
actually consumed. But in practice this doesn't work very well as the
scheduler expects the sched_clock time to be synchronized between
cpus. It also uses sched_clock to measure the time a task spends
sleeping, in which case "unstolen time" isn't meaningful.
So just use plain xen_clocksource_read to return wallclock nanoseconds
for sched_clock.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
phy/marvell: add 88ec048 support
igb: Program MDICNFG register prior to PHY init
e1000e: correct MAC-PHY interconnect register offset for 82579
hso: Add new product ID
can: Add driver for esd CAN-USB/2 device
l2tp: fix export of header file for userspace
can-raw: Fix skb_orphan_try handling
Revert "net: remove zap_completion_queue"
net: cleanup inclusion
phy/marvell: add 88e1121 interface mode support
u32: negative offset fix
net: Fix a typo from "dev" to "ndev"
igb: Use irq_synchronize per vector when using MSI-X
ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
e1000e: Fix irq_synchronize in MSI-X case
e1000e: register pm_qos request on hardware activation
ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
net: Add getsockopt support for TCP thin-streams
cxgb4: update driver version
cxgb4: add new PCI IDs
...
Manually fix up conflicts in:
- drivers/net/e1000e/netdev.c: due to pm_qos registration
infrastructure changes
- drivers/net/phy/marvell.c: conflict between adding 88ec048 support
and cleaning up the IDs
- drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
conflict (registration change vs marking it static)
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (88 commits)
ips driver: make it less chatty
intel_scu_ipc: fix size field for intel_scu_ipc_command
intel_scu_ipc: return -EIO for error condition in busy_loop
intel_scu_ipc: fix data packing of PMIC command on Moorestown
Clean up command packing on MRST.
zero the stack buffer before giving random garbage to the SCU
Fix stack buffer size for IPC writev messages
intel_scu_ipc: Use the new cpu identification function
intel_scu_ipc: tidy up unused bits
Remove indirect read write api support.
intel_scu_ipc: Support Medfield processors
intel_scu_ipc: detect CPU type automatically
x86 plat: limit x86 platform driver menu to X86
acpi ec_sys: Be more cautious about ec write access
acpi ec: Fix possible double io port registration
hp-wmi: acpi_drivers.h is already included through acpi.h two lines below
hp-wmi: Fix mixing up of and/or directive
dell-laptop: make dell_laptop_i8042_filter() static
asus-laptop: fix asus_input_init error path
msi-wmi: make needlessly global symbols static
...
Power limit notification feature is published in Intel 64 and IA-32
Architectures SDMV Vol 3A 14.5.6 Power Limit Notification.
It is implemented first on Intel Sandy Bridge platform.
The patch handles notification interrupt. Interrupt handler dumps power limit
information in log_buf, logs the event in mce log, and increases the event
counters (core_power_limit and package_power_limit). Upper level applications
could use the data to detect system health or diagnose functionality/performance
issues.
In the future, the event could be handled in a more fancy way.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
LKML-Reference: <1280448826-12004-5-git-send-email-fenghua.yu@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add package level thermal throttle interrupt support. The interrupt handler
increases package level thermal throttle count. It also logs the event in MCE
log.
The package level thermal throttle interrupt happens across threads in a
package. Each thread handles the interrupt individually. User level application
is supposed to retrieve correct event count and log based on package/thread
topology. This is the same situation for core level interrupt handler. In the
future, interrupt may be reported only per package or per core.
core_throttle_count and package_throttle_count are used for user interface.
Previously only throttle_count is used for core throttle count. If you think
new core_throttle_count name breaks user interface, I can change this part.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
LKML-Reference: <1280448826-12004-4-git-send-email-fenghua.yu@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch adds a hwmon driver for package level thermal control. The driver
dumps package level thermal information through sysfs interface so that upper
level application (e.g. lm_sensor) can retrive the information.
Instead of having the package level hwmon code in coretemp, I write a seperate
driver pkgtemp because:
First, package level thermal sensors include not only sensors for each core,
but also sensors for uncore, memory controller or other components in the
package. Logically it will be clear to have a seperate hwmon driver for package
level hwmon to monitor wider range of sensors in a package. Merging package
thermal driver into core thermal driver doesn't make sense and may mislead.
Secondly, merging the two drivers together may cause coding mess. It's easier
to include various package level sensors info if more sensor information is
implemented. Coretemp code needs to consider a lot of legacy machine cases.
Pkgtemp code only considers platform starting from Sandy Bridge.
On a 1Sx4Cx2T Sandy Bridge platform, lm-sensors dumps the pkgtemp and coretemp:
pkgtemp-isa-0000
Adapter: ISA adapter
physical id 0: +33.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0001
Adapter: ISA adapter
Core 1: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0002
Adapter: ISA adapter
Core 2: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0003
Adapter: ISA adapter
Core 3: +32.0°C (high = +79.0°C, crit = +99.0°C)
[ hpa: folded v3 patch removing improper global variable "SHOW" ]
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
LKML-Reference: <1280448826-12004-3-git-send-email-fenghua.yu@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The only machines this is triggering on should be supported by
acpi-cpufreq or acpi's internal throttling.
Signed-off-by: Dave Jones <davej@redhat.com>
Use __cpuinit instead of __init for the cpufreq_driver
init function like it is done in powernow-k8.c.
This is removing the warning generated when compiling with
the CONFIG_DEBUG_SECTION_MISMATCH=y option.
Signed-off-by: Holger Hans Peter Freyther <holger@moiji-mobile.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Use __cpuinit instead of __init for the cpufreq_driver
init function like it is done in powernow-k8.c. Use the
__cpuinitdata for data used by the routines marked as __cpuinit.
This is removing the warning generated when compiling with
the CONFIG_DEBUG_SECTION_MISMATCH=y option.
Signed-off-by: Holger Hans Peter Freyther <holger@moiji-mobile.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Use __cpuinit instead of __init for the cpufreq_driver
init function like it is done in powernow-k8.c.
This is removing the warning generated when compiling with
the CONFIG_DEBUG_SECTION_MISMATCH=y option.
Signed-off-by: Holger Hans Peter Freyther <holger@moiji-mobile.com>
Signed-off-by: Dave Jones <davej@redhat.com>
rdmsr() takes the lower 32 bits as a second argument and the high 32 as
a third. Fix the names accordingly since they were swapped.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Dave Jones <davej@redhat.com>
and fix the broken case if a core's frequency depends on others.
trace_power_frequency was only implemented in a rather ungeneric way
in acpi-cpufreq driver's target() function only.
-> Move the call to trace_power_frequency to
cpufreq.c:cpufreq_notify_transition() where CPUFREQ_POSTCHANGE
notifier is triggered.
This will support power frequency tracing by all cpufreq drivers
trace_power_frequency did not trace frequency changes correctly when
the userspace governor was used or when CPU cores' frequency depend
on each other.
-> Moving this into the CPUFREQ_POSTCHANGE notifier and pass the cpu
which gets switched automatically fixes this.
Robert Schoene provided some important fixes on top of my initial
quick shot version which are integrated in this patch:
- Forgot some changes in power_end trace (TP_printk/variable names)
- Variable dummy in power_end must now be cpu_id
- Use static 64 bit variable instead of unsigned int for cpu_id
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: davej@redhat.com
CC: arjan@infradead.org
CC: linux-kernel@vger.kernel.org
CC: robert.schoene@tu-dresden.de
Tested-by: robert.schoene@tu-dresden.de
Signed-off-by: Dave Jones <davej@redhat.com>
