When receiving incoming connection to specific services, always use
general bonding. This ensures that the link key gets stored and can be
used for further authentications.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When attempting to setup eSCO connections it can happen that some link
manager implementations fail to properly negotiate the eSCO parameters
and thus fail the eSCO setup. Normally the link manager is responsible
for the negotiation of the parameters and actually fallback to SCO if
no agreement can be reached. In cases where the link manager is just too
stupid, then at least try to establish a SCO link if eSCO fails.
For the Bluetooth devices with EDR support this includes handling packet
types of EDR basebands. This is particular tricky since for the EDR the
logic of enabling/disabling one specific packet type is turned around.
This fix contains an extra bitmask to disable eSCO EDR packet when
trying to fallback to a SCO connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A role switch with devices following the Bluetooth pre-2.1 standards
or without Encryption Pause and Resume support is not possible if
encryption is enabled. Most newer headsets require the role switch,
but also require that the connection is encrypted.
For connections with a high security mode setting, the link will be
immediately dropped. When the connection uses medium security mode
setting, then a grace period is introduced where the TX is halted and
the remote device gets a change to re-enable encryption after the
role switch. If not re-enabled the link will be dropped.
Based on initial work by Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current security model is based around the flags AUTH, ENCRYPT and
SECURE. Starting with support for the Bluetooth 2.1 specification this is
no longer sufficient. The different security levels are now defined as
SDP, LOW, MEDIUM and SECURE.
Previously it was possible to set each security independently, but this
actually doesn't make a lot of sense. For Bluetooth the encryption depends
on a previous successful authentication. Also you can only update your
existing link key if you successfully created at least one before. And of
course the update of link keys without having proper encryption in place
is a security issue.
The new security levels from the Bluetooth 2.1 specification are now
used internally. All old settings are mapped to the new values and this
way it ensures that old applications still work. The only limitation
is that it is no longer possible to set authentication without also
enabling encryption. No application should have done this anyway since
this is actually a security issue. Without encryption the integrity of
the authentication can't be guaranteed.
As default for a new L2CAP or RFCOMM connection, the LOW security level
is used. The only exception here are the service discovery sessions on
PSM 1 where SDP level is used. To have similar security strength as with
a Bluetooth 2.0 and before combination key, the MEDIUM level should be
used. This is according to the Bluetooth specification. The MEDIUM level
will not require any kind of man-in-the-middle (MITM) protection. Only
the HIGH security level will require this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to decide if listening RFCOMM sockets should be accept()ed
the BD_ADDR of the remote device needs to be known. This patch adds
a socket option which defines a timeout for deferring the actual
connection setup.
The connection setup is done after reading from the socket for the
first time. Until then writing to the socket returns ENOTCONN.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The L2CAP and RFCOMM applications require support for authorization
and the ability of rejecting incoming connection requests. The socket
interface is not really able to support this.
This patch does the ground work for a socket option to defer connection
setup. Setting this option allows calling of accept() and then the
first read() will trigger the final connection setup. Calling close()
would reject the connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the return value of nlmsg_notify() as follows:
If NETLINK_BROADCAST_ERROR is set by any of the listeners and
an error in the delivery happened, return the broadcast error;
else if there are no listeners apart from the socket that
requested a change with the echo flag, return the result of the
unicast notification. Thus, with this patch, the unicast
notification is handled in the same way of a broadcast listener
that has set the NETLINK_BROADCAST_ERROR socket flag.
This patch is useful in case that the caller of nlmsg_notify()
wants to know the result of the delivery of a netlink notification
(including the broadcast delivery) and take any action in case
that the delivery failed. For example, ctnetlink can drop packets
if the event delivery failed to provide reliable logging and
state-synchronization at the cost of dropping packets.
This patch also modifies the rtnetlink code to ignore the return
value of rtnl_notify() in all callers. The function rtnl_notify()
(before this patch) returned the error of the unicast notification
which makes rtnl_set_sk_err() reports errors to all listeners. This
is not of any help since the origin of the change (the socket that
requested the echoing) notices the ENOBUFS error if the notification
fails and should resync itself.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: fix double free at netns creation
veth : add the set_mac_address capability
sunlance: Beyond ARRAY_SIZE of ib->btx_ring
sungem: another error printed one too early
ISDN: fix sc/shmem printk format warning
SMSC: timeout reaches -1
smsc9420: handle magic field of ethtool_eeprom
sundance: missing parentheses?
smsc9420: fix another postfixed timeout
wimax/i2400m: driver loads firmware v1.4 instead of v1.3
vlan: Update skb->mac_header in __vlan_put_tag().
cxgb3: Add support for PCI ID 0x35.
tcp: remove obsoleted comment about different passes
TG3: &&/|| confusion
ATM: misplaced parentheses?
net/mv643xx: don't disable the mib timer too early and lock properly
net/mv643xx: use GFP_ATOMIC while atomic
atl1c: Atheros L1C Gigabit Ethernet driver
net: Kill skb_truesize_check(), it only catches false-positives.
net: forcedeth: Fix wake-on-lan regression
It turns out that net_alive is unnecessary, and the original problem
that led to it being added was simply that the icmp code thought
it was a network device and wound up being unable to handle packets
while there were still packets in the network namespace.
Now that icmp and tcp have been fixed to properly register themselves
this problem is no longer present and we have a stronger guarantee
that packets will not arrive in a network namespace then that provided
by net_alive in netif_receive_skb. So remove net_alive allowing
packet reception run a little faster.
Additionally document the strong reason why network namespace cleanup
is safe so that if something happens again someone else will have
a chance of figuring it out.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the sysdev_suspend/resume from the callee to the callers, with
no real change in semantics, so that we can rework the disabling of
interrupts during suspend/hibernation.
This is based on an earlier patch from Linus.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* hibernate:
PM: Fix suspend_console and resume_console to use only one semaphore
PM: Wait for console in resume
PM: Fix pm_notifiers during user mode hibernation
swsusp: clean up shrink_all_zones()
swsusp: dont fiddle with swappiness
PM: fix build for CONFIG_PM unset
PM/hibernate: fix "swap breaks after hibernation failures"
PM/resume: wait for device probing to finish
Consolidate driver_probe_done() loops into one place
there's a few places that currently loop over driver_probe_done(), and
I'm about to add another one. This patch abstracts it into a helper
to reduce duplication.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (26 commits)
drm/radeon: update sarea copies of last_ variables on resume.
drm/i915: Keep refs on the object over the lifetime of vmas for GTT mmap.
drm/i915: take struct mutex around fb unref
drm: Use spread spectrum when the bios tells us it's ok.
drm: Collapse identical i8xx_clock() and i9xx_clock().
drm: Bring PLL limits in sync with DDX values.
drm: Add locking around cursor gem operations.
drm: Propagate failure from setting crtc base.
drm: Check for a NULL encoder when reverting on error path
drm/i915: Cleanup the hws on ringbuffer constrution failure.
drm/i915: Don't add panel_fixed_mode to the probed modes list at LVDS init.
drm: Release user fbs in drm_release
drm/i915: Unpin the fb on error during construction.
drm/i915: Unpin the hws if we fail to kmap.
drm/i915: Unpin the ringbuffer if we fail to ioremap it.
drm/i915: unpin for an invalid memory domain.
drm/i915: Release and unlock on mmap_gtt error path.
drm/i915: Set framebuffer alignment based upon the fence constraints.
drm: Do not leak a new reference for flink() on an existing name
drm/i915: Fix potential AB-BA deadlock in i915_gem_execbuffer()
...
Intel 8257x Ethernet boards have a feature called Serial Over Lan.
This feature works by emulating a serial port, and it is detected by
kernel as a normal 8250 port. However, this emulation is not perfect, as
also noticed on changeset 7500b1f602.
Before this patch, the kernel were trying to check if the serial TX is
capable of work using IRQ's.
This were done with a code similar this:
serial_outp(up, UART_IER, UART_IER_THRI);
lsr = serial_in(up, UART_LSR);
iir = serial_in(up, UART_IIR);
serial_outp(up, UART_IER, 0);
if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT)
up->bugs |= UART_BUG_TXEN;
This works fine for other 8250 ports, but, on 8250-emulated SoL port, the
chip is a little lazy to down UART_IIR_NO_INT at UART_IIR register.
Due to that, UART_BUG_TXEN is sometimes enabled. However, as TX IRQ keeps
working, and the TX polling is now enabled, the driver miss-interprets the
IRQ received later, hanging up the machine until a key is pressed at the
serial console.
This is the 6 version of this patch. Previous versions were trying to
introduce a large enough delay between serial_outp and serial_in(up,
UART_IIR), but not taking forever. However, the needed delay couldn't be
safely determined.
At the experimental tests, a delay of 1us solves most of the cases, but
still hangs sometimes. Increasing the delay to 5us was better, but still
doesn't solve. A very high delay of 50 ms seemed to work every time.
However, poking around with delays and pray for it to be enough doesn't
seem to be a good approach, even for a quirk.
So, instead of playing with random large arbitrary delays, let's just
disable UART_BUG_TXEN for all SoL ports.
[akpm@linux-foundation.org: fix warnings]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds more documentation of the lowlevel API to avoid future bugs.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kzfree() is a wrapper for kfree() that additionally zeroes the underlying
memory before releasing it to the slab allocator.
Currently there is code which memset()s the memory region of an object
before releasing it back to the slab allocator to make sure
security-sensitive data are really zeroed out after use.
These callsites can then just use kzfree() which saves some code, makes
users greppable and allows for a stupid destructor that isn't necessarily
aware of the actual object size.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Matt Mackall <mpm@selenic.com>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds NETLINK_BROADCAST_ERROR which is a netlink
socket option that the listener can set to make netlink_broadcast()
return errors in the delivery to the caller. This option is useful
if the caller of netlink_broadcast() do something with the result
of the message delivery, like in ctnetlink where it drops a network
packet if the event delivery failed, this is used to enable reliable
logging and state-synchronization. If this socket option is not set,
netlink_broadcast() only reports ESRCH errors and silently ignore
ENOBUFS errors, which is what most netlink_broadcast() callers
should do.
This socket option is based on a suggestion from Patrick McHardy.
Patrick McHardy can exchange this patch for a beer from me ;).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes potential fault at fault time if the object was unreferenced
while the mapping still existed. Now, while the mmap_offset only lives
for the lifetime of the object, the object also stays alive while a vma
exists that needs it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check the error paths within intel_pipe_set_base() to first cleanup and
then report back the error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Avoids leaking fbs and associated buffers on release.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Tested-by: Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
After moving mac addresses in __vlan_put_tag() skb->mac_header needs
to be updated.
Reported-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: fix deadlock in blk_abort_queue() for drivers that readd to timeout list
block: fix booting from partitioned md array
block: revert part of 18ce3751cc
cciss: PCI power management reset for kexec
paride/pg.c: xs(): &&/|| confusion
fs/bio: bio_alloc_bioset: pass right object ptr to mempool_free
block: fix bad definition of BIO_RW_SYNC
bsg: Fix sense buffer bug in SG_IO
Since I don't work for SUSE any more and the bwalle@suse.de address is
invalid, correct it in the copyright headers and documentation.
Signed-off-by: Bernhard Walle <bernhard.walle@gmx.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have a Digi Neo 8 PCI card (114f:00b1) Serial controller: Digi
International Digi Neo 8 (rev 05)
that works with the jsm driver after using the following patch.
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Cc: Scott H Kilau <Scott_Kilau@digi.com>
Cc: Wendy Xiong <wendyx@us.ibm.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now, early_pfn_in_nid(PFN, NID) may returns false if PFN is a hole.
and memmap initialization was not done. This was a trouble for
sparc boot.
To fix this, the PFN should be initialized and marked as PG_reserved.
This patch changes early_pfn_in_nid() return true if PFN is a hole.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reported-by: David Miller <davem@davemlloft.net>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
What's happening is that the assertion in mm/page_alloc.c:move_freepages()
is triggering:
BUG_ON(page_zone(start_page) != page_zone(end_page));
Once I knew this is what was happening, I added some annotations:
if (unlikely(page_zone(start_page) != page_zone(end_page))) {
printk(KERN_ERR "move_freepages: Bogus zones: "
"start_page[%p] end_page[%p] zone[%p]\n",
start_page, end_page, zone);
printk(KERN_ERR "move_freepages: "
"start_zone[%p] end_zone[%p]\n",
page_zone(start_page), page_zone(end_page));
printk(KERN_ERR "move_freepages: "
"start_pfn[0x%lx] end_pfn[0x%lx]\n",
page_to_pfn(start_page), page_to_pfn(end_page));
printk(KERN_ERR "move_freepages: "
"start_nid[%d] end_nid[%d]\n",
page_to_nid(start_page), page_to_nid(end_page));
...
And here's what I got:
move_freepages: Bogus zones: start_page[2207d0000] end_page[2207dffc0] zone[fffff8103effcb00]
move_freepages: start_zone[fffff8103effcb00] end_zone[fffff8003fffeb00]
move_freepages: start_pfn[0x81f600] end_pfn[0x81f7ff]
move_freepages: start_nid[1] end_nid[0]
My memory layout on this box is:
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x0081ff5d
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[8] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00020000
[ 0.000000] 1: 0x00800000 -> 0x0081f7ff
[ 0.000000] 1: 0x0081f800 -> 0x0081fe50
[ 0.000000] 1: 0x0081fed1 -> 0x0081fed8
[ 0.000000] 1: 0x0081feda -> 0x0081fedb
[ 0.000000] 1: 0x0081fedd -> 0x0081fee5
[ 0.000000] 1: 0x0081fee7 -> 0x0081ff51
[ 0.000000] 1: 0x0081ff59 -> 0x0081ff5d
So it's a block move in that 0x81f600-->0x81f7ff region which triggers
the problem.
This patch:
Declaration of early_pfn_to_nid() is scattered over per-arch include
files, and it seems it's complicated to know when the declaration is used.
I think it makes fix-for-memmap-init not easy.
This patch moves all declaration to include/linux/mm.h
After this,
if !CONFIG_NODES_POPULATES_NODE_MAP && !CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID
-> Use static definition in include/linux/mm.h
else if !CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID
-> Use generic definition in mm/page_alloc.c
else
-> per-arch back end function will be called.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reported-by: David Miller <davem@davemlloft.net>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The conversion of atmel-mci to dma_request_channel missed the
initialization of the channel dma_slave information. The filter_fn passed
to dma_request_channel is responsible for initializing the channel's
private data. This implementation has the additional benefit of enabling
a generic client-channel data passing mechanism.
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
YAMAMOTO-san noticed that task_dirty_inc doesn't seem to be called properly for
cases where set_page_dirty is not used to dirty a page (eg. mark_buffer_dirty).
Additionally, there is some inconsistency about when task_dirty_inc is
called. It is used for dirty balancing, however it even gets called for
__set_page_dirty_no_writeback.
So rather than increment it in a set_page_dirty wrapper, move it down to
exactly where the dirty page accounting stats are incremented.
Cc: YAMAMOTO Takashi <yamamoto@valinux.co.jp>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As requested by Michael, add a missing check for valid flags in
timerfd_settime(), and make it return EINVAL in case some extra bits are
set.
Michael said:
If this is to be any use to userland apps that want to check flag
support (perhaps it is too late already), then the sooner we get it
into the kernel the better: 2.6.29 would be good; earlier stables as
well would be even better.
[akpm@linux-foundation.org: remove unused TFD_FLAGS_SET]
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: <stable@kernel.org> [2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently seq_read assumes that the offset passed to it is always the
offset it passed to user space. In the case pread this assumption is
broken and we do the wrong thing when presented with pread.
To solve this I introduce an offset cache inside of struct seq_file so we
know where our logical file position is. Then in seq_read if we try to
read from another offset we reset our data structures and attempt to go to
the offset user space wanted.
[akpm@linux-foundation.org: restore FMODE_PWRITE]
[pjt@google.com: seq_open needs its fmode opened up to take advantage of this]
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Paul Turner <pjt@google.com>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Separate FMODE_PREAD and FMODE_PWRITE into separate flags to reflect the
reality that the read and write paths may have independent restrictions.
A git grep verifies that these flags are always cleared together so this
new behavior will only apply to interfaces that change to clear flags
individually.
This is required for "seq_file: properly cope with pread", a post-2.6.25
regression fix.
[akpm@linux-foundation.org: add comment]
Signed-off-by: Paul Turner <pjt@google.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have get_vm_area_caller() and __get_vm_area() but not
__get_vm_area_caller()
On powerpc, I use __get_vm_area() to separate the ranges of addresses
given to vmalloc vs. ioremap (various good reasons for that) so in order
to be able to implement the new caller tracking in /proc/vmallocinfo, I
need a "_caller" variant of it.
(akpm: needed for ongoing powerpc development, so merge it early)
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The untracked conntrack actually does usually have events marked for
delivery as its not special-cased in that part of the code. Skip the
actual delivery since it impacts performance noticeably.
Signed-off-by: Patrick McHardy <kaber@trash.net>
In NFLOG the per-rule qthreshold should overrides per-instance only
it is set. With current code, the per-rule qthreshold is 1 if not set
and it overrides the per-instance qthreshold.
This patch modifies the default xt_NFLOG threshold from 1 to
0. Thus a value of 0 means there is no per-rule setting and the instance
parameter has to apply.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
We can't OR shift values, so get rid of BIO_RW_SYNC and use BIO_RW_SYNCIO
and BIO_RW_UNPLUG explicitly. This brings back the behaviour from before
213d9417fe.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
A long time ago we had bugs, primarily in TCP, where we would modify
skb->truesize (for TSO queue collapsing) in ways which would corrupt
the socket memory accounting.
skb_truesize_check() was added in order to try and catch this error
more systematically.
However this debugging check has morphed into a Frankenstein of sorts
and these days it does nothing other than catch false-positives.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this sparse warnings:
drivers/net/hamradio/hdlcdrv.c:274:34: warning: incorrect type in argument 2 (different signedness)
drivers/net/hamradio/hdlcdrv.c:279:47: warning: incorrect type in argument 2 (different signedness)
drivers/net/hamradio/hdlcdrv.c:288:39: warning: incorrect type in argument 2 (different signedness)
drivers/net/hamradio/hdlcdrv.c:300:47: warning: incorrect type in argument 2 (different signedness)
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, vm86: fix preemption bug
x86, olpc: fix model detection without OFW
x86, hpet: fix for LS21 + HPET = boot hang
x86: CPA avoid repeated lazy mmu flush
x86: warn if arch_flush_lazy_mmu_cpu is called in preemptible context
x86/paravirt: make arch_flush_lazy_mmu/cpu disable preemption
x86, pat: fix warn_on_once() while mapping 0-1MB range with /dev/mem
x86/cpa: make sure cpa is safe to call in lazy mmu mode
x86, ptrace, mm: fix double-free on race
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Fix NULL dereference in ext4_ext_migrate()'s error handling
ext4: Implement range_cyclic in ext4_da_writepages instead of write_cache_pages
ext4: Initialize preallocation list_head's properly
ext4: Fix lockdep warning
ext4: Fix to read empty directory blocks correctly in 64k
jbd2: Avoid possible NULL dereference in jbd2_journal_begin_ordered_truncate()
Revert "ext4: wait on all pending commits in ext4_sync_fs()"
jbd2: Fix return value of jbd2_journal_start_commit()
During peeloff/accept() sctp needs to save the parent socket state
into the new socket so that any options set on the parent are
inherited by the child socket. This was found when the
parent/listener socket issues SO_BINDTODEVICE, but the
data was misrouted after a route cache flush.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP incorrectly doubles rto ever time a Hearbeat chunk
is generated. However RFC 4960 states:
On an idle destination address that is allowed to heartbeat, it is
recommended that a HEARTBEAT chunk is sent once per RTO of that
destination address plus the protocol parameter 'HB.interval', with
jittering of +/- 50% of the RTO value, and exponential backoff of the
RTO if the previous HEARTBEAT is unanswered.
Essentially, of if the heartbean is unacknowledged, do we double the RTO.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
