The TILE-Gx chip includes a packet-processing network engine called
mPIPE ("Multicore Programmable Intelligent Packet Engine"). This
change adds support for using the mPIPE engine from within the
kernel. The engine has more functionality than is exposed here,
but to keep the kernel code and binary simpler, this is a subset
of the full API designed to enable standard Linux networking only.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The dma_queue support is used by both the mPipe (networking)
and Trio (PCI) hardware shims on tilegx. This common code is
selected when either of those drivers is built.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Add support for MMIO read/write on tilegx to support GXIO IORPC access.
Similar to the asm-generic version, but we include memory fences on
the writes to be conservative.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The GXIO I/O RPC subsystem handles exporting I/O hardware resources to
Linux and to applications running under Linux.
For instance, memory which is made available for I/O DMA must be mapped
by an I/O TLB; that means that such memory must be locked down by Linux,
so that it is not swapped or otherwise reused, as long as those I/O
TLB entries are active. Similarly, configuring direct hardware access
introduces new validation requirements. If a user application registers
memory, Linux must ensure that the supplied virtual addresses are valid,
and turn them into client physical addresses. Similarly, when Linux then
supplies those client physical addresses to the Tilera hypervisor, it
must in turn validate those before turning them into the real physical
addresses which are required by the hardware.
To the extent that these sorts of activities were required on previous
TILE architecture processors, they were implemented in a device-specific
fashion. This meant that every I/O device had its own Tilera hypervisor
driver, its own Linux driver, and in some cases its own user-level
library support. There was a large amount of more-or-less functionally
identical code in different places, particularly in the different Linux
drivers. For TILE-Gx, this support has been generalized into a common
framework, known as the I/O RPC framework or just IORPC.
The two "gxio" directories (one for headers, one for sources) start
with just a few files in each with this infrastructure commit, but
after adding support for the on-board I/O shims for networking, PCI,
USB, crypto, compression, I2CS, etc., there end up being about 20 files
in each directory.
More information on the IORPC framework is in the <hv/iorpc.h> header,
included in this commit.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
* pci/myron-pcibios_setup:
xtensa/PCI: factor out pcibios_setup()
x86/PCI: adjust section annotations for pcibios_setup()
unicore32/PCI: adjust section annotations for pcibios_setup()
tile/PCI: factor out pcibios_setup()
sparc/PCI: factor out pcibios_setup()
sh/PCI: adjust section annotations for pcibios_setup()
sh/PCI: factor out pcibios_setup()
powerpc/PCI: factor out pcibios_setup()
parisc/PCI: factor out pcibios_setup()
MIPS/PCI: adjust section annotations for pcibios_setup()
MIPS/PCI: factor out pcibios_setup()
microblaze/PCI: factor out pcibios_setup()
ia64/PCI: factor out pcibios_setup()
cris/PCI: factor out pcibios_setup()
alpha/PCI: factor out pcibios_setup()
PCI: pull pcibios_setup() up into core
The PCI core provides a generic pcibios_setup() routine. Drop this
architecture-specific version in favor of that.
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
mn10300 has a header (in its include/asm directory) that is a thin
wrapper around asm-generic/ipc.h. This wrapper is useless, since that
header doesn't exist. It is also unused (no file includes asm/ipc.h).
hexagon and tile generate similar headers at build time (using a
generic-y entry in include/asm/Kbuild). These generated headers are
useless and unused too.
Remove this header and these generic-y entries.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: David Howells <dhowells@redhat.com> [MN10300]
Signed-off-by: Michal Marek <mmarek@suse.cz>
Instruction bundles are always little-endian, even when running in
big-endian mode. I missed this internal bug fix when cherry-picking
the big-endian code to return to the community.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The definition of 32-bit values in the 64-bit tilegx architecture is that
they should be sign-extended regardless of whether they are considered
signed or unsigned by the compiler. Accordingly, we need to use an
"ld4s" rather than "ld4u" to load and sign-extend for get_user().
This fixes glibc bug 14238 (see http://sourceware.org/bugzilla),
introduced during the 3.5 merge window.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
It will update busn_res accordingly, so we get that for last_busno.
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Replace the struct pci_bus secondary/subordinate members with the
struct resource busn_res. Later we'll build a resource tree of these
bus numbers.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some code was moved from init_task.c to setup.c but the appropriate
header needed to be moved as well.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This routine isn't used unless CONFIG_HOMECACHE is enabled, which
isn't even available as a public configuration option yet.
Since it no longer links correctly in 3.4, just remove it for now.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
ipi_call_lock/unlock() lock resp. unlock call_function.lock. This lock
protects only the call_function data structure itself, but it's
completely unrelated to cpu_online_mask. The mask to which the IPIs
are sent is calculated before call_function.lock is taken in
smp_call_function_many(), so the locking around set_cpu_online() is
pointless and can be removed.
[ tglx: Massaged changelog ]
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: ralf@linux-mips.org
Cc: sshtylyov@mvista.com
Cc: david.daney@cavium.com
Cc: nikunj@linux.vnet.ibm.com
Cc: paulmck@linux.vnet.ibm.com
Cc: axboe@kernel.dk
Cc: peterz@infradead.org
Cc: Chris Metcalf <cmetcalf@tilera.com>
Link: http://lkml.kernel.org/r/1338275765-3217-6-git-send-email-yong.zhang0@gmail.com
Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull third pile of signal handling patches from Al Viro:
"This time it's mostly helpers and conversions to them; there's a lot
of stuff remaining in the tree, but that'll either go in -rc2
(isolated bug fixes, ideally via arch maintainers' trees) or will sit
there until the next cycle."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
x86: get rid of calling do_notify_resume() when returning to kernel mode
blackfin: check __get_user() return value
whack-a-mole with TIF_FREEZE
FRV: Optimise the system call exit path in entry.S [ver #2]
FRV: Shrink TIF_WORK_MASK [ver #2]
FRV: Prevent syscall exit tracing and notify_resume at end of kernel exceptions
new helper: signal_delivered()
powerpc: get rid of restore_sigmask()
most of set_current_blocked() callers want SIGKILL/SIGSTOP removed from set
set_restore_sigmask() is never called without SIGPENDING (and never should be)
TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set
don't call try_to_freeze() from do_signal()
pull clearing RESTORE_SIGMASK into block_sigmask()
sh64: failure to build sigframe != signal without handler
openrisc: tracehook_signal_handler() is supposed to be called on success
new helper: sigmask_to_save()
new helper: restore_saved_sigmask()
new helpers: {clear,test,test_and_clear}_restore_sigmask()
HAVE_RESTORE_SIGMASK is defined on all architectures now
Pull vfs changes from Al Viro.
"A lot of misc stuff. The obvious groups:
* Miklos' atomic_open series; kills the damn abuse of
->d_revalidate() by NFS, which was the major stumbling block for
all work in that area.
* ripping security_file_mmap() and dealing with deadlocks in the
area; sanitizing the neighborhood of vm_mmap()/vm_munmap() in
general.
* ->encode_fh() switched to saner API; insane fake dentry in
mm/cleancache.c gone.
* assorted annotations in fs (endianness, __user)
* parts of Artem's ->s_dirty work (jff2 and reiserfs parts)
* ->update_time() work from Josef.
* other bits and pieces all over the place.
Normally it would've been in two or three pull requests, but
signal.git stuff had eaten a lot of time during this cycle ;-/"
Fix up trivial conflicts in Documentation/filesystems/vfs.txt (the
'truncate_range' inode method was removed by the VM changes, the VFS
update adds an 'update_time()' method), and in fs/btrfs/ulist.[ch] (due
to sparse fix added twice, with other changes nearby).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (95 commits)
nfs: don't open in ->d_revalidate
vfs: retry last component if opening stale dentry
vfs: nameidata_to_filp(): don't throw away file on error
vfs: nameidata_to_filp(): inline __dentry_open()
vfs: do_dentry_open(): don't put filp
vfs: split __dentry_open()
vfs: do_last() common post lookup
vfs: do_last(): add audit_inode before open
vfs: do_last(): only return EISDIR for O_CREAT
vfs: do_last(): check LOOKUP_DIRECTORY
vfs: do_last(): make ENOENT exit RCU safe
vfs: make follow_link check RCU safe
vfs: do_last(): use inode variable
vfs: do_last(): inline walk_component()
vfs: do_last(): make exit RCU safe
vfs: split do_lookup()
Btrfs: move over to use ->update_time
fs: introduce inode operation ->update_time
reiserfs: get rid of resierfs_sync_super
reiserfs: mark the superblock as dirty a bit later
...
Does block_sigmask() + tracehook_signal_handler(); called when
sigframe has been successfully built. All architectures converted
to it; block_sigmask() itself is gone now (merged into this one).
I'm still not too happy with the signature, but that's a separate
story (IMO we need a structure that would contain signal number +
siginfo + k_sigaction, so that get_signal_to_deliver() would fill one,
signal_delivered(), handle_signal() and probably setup...frame() -
take one).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Only 3 out of 63 do not. Renamed the current variant to __set_current_blocked(),
added set_current_blocked() that will exclude unblockable signals, switched
open-coded instances to it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
replace boilerplate "should we use ->saved_sigmask or ->blocked?"
with calls of obvious inlined helper...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
first fruits of ..._restore_sigmask() helpers: now we can take
boilerplate "signal didn't have a handler, clear RESTORE_SIGMASK
and restore the blocked mask from ->saved_mask" into a common
helper. Open-coded instances switched...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull second pile of signal handling patches from Al Viro:
"This one is just task_work_add() series + remaining prereqs for it.
There probably will be another pull request from that tree this
cycle - at least for helpers, to get them out of the way for per-arch
fixes remaining in the tree."
Fix trivial conflict in kernel/irq/manage.c: the merge of Andrew's pile
had brought in commit 97fd75b7b8 ("kernel/irq/manage.c: use the
pr_foo() infrastructure to prefix printks") which changed one of the
pr_err() calls that this merge moves around.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
keys: kill task_struct->replacement_session_keyring
keys: kill the dummy key_replace_session_keyring()
keys: change keyctl_session_to_parent() to use task_work_add()
genirq: reimplement exit_irq_thread() hook via task_work_add()
task_work_add: generic process-context callbacks
avr32: missed _TIF_NOTIFY_RESUME on one of do_notify_resume callers
parisc: need to check NOTIFY_RESUME when exiting from syscall
move key_repace_session_keyring() into tracehook_notify_resume()
TIF_NOTIFY_RESUME is defined on all targets now
Pull tile updates from Chris Metcalf:
"These changes cover a range of new arch/tile features and
optimizations. They've been through LKML review and on linux-next for
a month or so. There's also one bug-fix that just missed 3.4, which
I've marked for stable."
Fixed up trivial conflict in arch/tile/Kconfig (new added tile Kconfig
entries clashing with the generic timer/clockevents changes).
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: default to tilegx_defconfig for ARCH=tile
tile: fix bug where fls(0) was not returning 0
arch/tile: mark TILEGX as not EXPERIMENTAL
tile/mm/fault.c: Port OOM changes to handle_page_fault
arch/tile: add descriptive text if the kernel reports a bad trap
arch/tile: allow querying cpu module information from the hypervisor
arch/tile: fix hardwall for tilegx and generalize for idn and ipi
arch/tile: support multiple huge page sizes dynamically
mm: add new arch_make_huge_pte() method for tile support
arch/tile: support kexec() for tilegx
arch/tile: support <asm/cachectl.h> header for cacheflush() syscall
arch/tile: Allow tilegx to build with either 16K or 64K page size
arch/tile: optimize get_user/put_user and friends
arch/tile: support building big-endian kernel
arch/tile: allow building Linux with transparent huge pages enabled
arch/tile: use interrupt critical sections less
There is no "ARCH=tile" (just like there is no "ARCH=x86") so we need
to pick a default configuration, either tilepro or tilegx, when users
specify ARCH=tile. We'll use tilegx, since that's our current chip.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This is because __builtin_clz(0) returns 64 for the "undefined" case
of 0, since the builtin just does a right-shift 32 and "clz" instruction.
So, use the alpha approach of casting to u32 and using __builtin_clzll().
Cc: stable@vger.kernel.org
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Also create a TILEPRO config setting to use for #ifdefs where it
is cleaner to do so, and make the 64BIT setting depend directly
on the setting of TILEGX.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Commit d065bd810b
(mm: retry page fault when blocking on disk transfer) and
commit 37b23e0525
(x86,mm: make pagefault killable)
The above commits introduced changes into the x86 pagefault handler
for making the page fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial
during OOM killer invocation.
Port these changes to tile.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
[cmetcalf@tilera.com: initialize "flags" after "write" updated.]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
If the kernel unexpectedly takes a bad trap, it's convenient to
have it report the type of trap as part of the error. This gives
customers a bit more context before they call up customer support.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This just adds a few more attributes to the information Linux
can query from the hypervisor for the /sys/hypervisor/board/ directory,
providing part, serial#, revision#, and description for cpu modules
(as opposed to the board itself, or any mezzanine boards).
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The hardwall drain code was not properly implemented for tilegx,
just tilepro, so you couldn't reliably restart an application that
made use of the udn.
In addition, the code was only applicable to the udn (user dynamic
network). On tilegx there is a second user network that is available
(the "idn"), and there is support for having I/O shims deliver
user-level interrupts to applications ("ipi") which functions in a
very similar way to the inter-core permissions used for udn/idn.
So this change also generalizes the code from supporting just the udn
to supports udn/idn/ipi on tilegx.
By default we now use /dev/hardwall/{udn,idn,ipi} with separate
minor numbers for the three devices.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This change adds support for a new "super" bit in the PTE, using the new
arch_make_huge_pte() method. The Tilera hypervisor sees the bit set at a
given level of the page table and gangs together 4, 16, or 64 consecutive
pages from that level of the hierarchy to create a larger TLB entry.
One extra "super" page size can be specified at each of the three levels
of the page table hierarchy on tilegx, using the "hugepagesz" argument
on the boot command line. A new hypervisor API is added to allow Linux
to tell the hypervisor how many PTEs to gang together at each level of
the page table.
To allow pre-allocating huge pages larger than the buddy allocator can
handle, this change modifies the Tilera bootmem support to put all of
memory on tilegx platforms into bootmem.
As part of this change I eliminate the vestigial CONFIG_HIGHPTE support,
which never worked anyway, and eliminate the hv_page_size() API in favor
of the standard vma_kernel_pagesize() API.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We already had a syscall that did some dcache flushing, but it was
not used in practice. Make it MIPS compatible instead so it can
do both the DCACHE and ICACHE actions. We have code that wants to
be able to use the ICACHE flush mode from userspace so this change
enables that.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This change introduces new flags for the hv_install_context()
API that passes a page table pointer to the hypervisor. Clients
can explicitly request 4K, 16K, or 64K small pages when they
install a new context. In practice, the page size is fixed at
kernel compile time and the same size is always requested every
time a new page table is installed.
The <hv/hypervisor.h> header changes so that it provides more abstract
macros for managing "page" things like PFNs and page tables. For
example there is now a HV_DEFAULT_PAGE_SIZE_SMALL instead of the old
HV_PAGE_SIZE_SMALL. The various PFN routines have been eliminated and
only PA- or PTFN-based ones remain (since PTFNs are always expressed
in fixed 2KB "page" size). The page-table management macros are
renamed with a leading underscore and take page-size arguments with
the presumption that clients will use those macros in some single
place to provide the "real" macros they will use themselves.
I happened to notice the old hv_set_caching() API was totally broken
(it assumed 4KB pages) so I changed it so it would nominally work
correctly with other page sizes.
Tag modules with the page size so you can't load a module built with
a conflicting page size. (And add a test for SMP while we're at it.)
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Use direct load/store for the get_user/put_user.
Previously, we would call out to a helper routine that would do the
appropriate thing and then return, handling the possible exception
internally. Now we inline the load or store, along with a "we succeeded"
indication in a register; if the load or store faults, we write a
"we failed" indication into the same register and then return to the
following instruction. This is more efficient and gives us more compact
code, as well as being more in line with what other architectures do.
The special futex assembly source file for TILE-Gx also disappears in
this change; we just use the same inlining idiom there as well, putting
the appropriate atomic operations directly into futex_atomic_op_inuser()
(and thus into the FUTEX_WAIT function).
The underlying atomic copy_from_user, copy_to_user functions were
renamed using the (cryptic) x86 convention as copy_from_user_ll and
copy_to_user_ll.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The toolchain supports big-endian mode now, so add support for building
the kernel to run big-endian as well.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The change adds some infrastructure for managing tile pmd's more generally,
using pte_pmd() and pmd_pte() methods to translate pmd values to and
from ptes, since on TILEPro a pmd is really just a nested structure
holding a pgd (aka pte). Several existing pmd methods are moved into
this framework, and a whole raft of additional pmd accessors are defined
that are used by the transparent hugepage framework.
The tile PTE now has a "client2" bit. The bit is used to indicate a
transparent huge page is in the process of being split into subpages.
This change also fixes a generic bug where the return value of the
generic pmdp_splitting_flush() was incorrect.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
In general we want to avoid ever touching memory while within an
interrupt critical section, since the page fault path goes through
a different path from the hypervisor when in an interrupt critical
section, and we carefully decided with tilegx that we didn't need
to support this path in the kernel. (On tilepro we did implement
that path as part of supporting atomic instructions in software.)
In practice we always need to touch the kernel stack, since that's
where we store the interrupt state before releasing the critical
section, but this change cleans up a few things. The IRQ_ENABLE
macro is split up so that when we want to enable interrupts in a
deferred way (e.g. for cpu_idle or for interrupt return) we can
read the per-cpu enable mask before entering the critical section.
The cache-migration code is changed to use interrupt masking instead
of interrupt critical sections. And, the interrupt-entry code is
changed so that we defer loading "tp" from per-cpu data until after
we have released the interrupt critical section.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Pull KVM changes from Avi Kivity:
"Changes include additional instruction emulation, page-crossing MMIO,
faster dirty logging, preventing the watchdog from killing a stopped
guest, module autoload, a new MSI ABI, and some minor optimizations
and fixes. Outside x86 we have a small s390 and a very large ppc
update.
Regarding the new (for kvm) rebaseless workflow, some of the patches
that were merged before we switch trees had to be rebased, while
others are true pulls. In either case the signoffs should be correct
now."
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
arch/powerpc/kvm/book3s_segment.S and arch/x86/include/asm/kvm_para.h.
I suspect the kvm_para.h resolution ends up doing the "do I have cpuid"
check effectively twice (it was done differently in two different
commits), but better safe than sorry ;)
* 'next' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (125 commits)
KVM: make asm-generic/kvm_para.h have an ifdef __KERNEL__ block
KVM: s390: onereg for timer related registers
KVM: s390: epoch difference and TOD programmable field
KVM: s390: KVM_GET/SET_ONEREG for s390
KVM: s390: add capability indicating COW support
KVM: Fix mmu_reload() clash with nested vmx event injection
KVM: MMU: Don't use RCU for lockless shadow walking
KVM: VMX: Optimize %ds, %es reload
KVM: VMX: Fix %ds/%es clobber
KVM: x86 emulator: convert bsf/bsr instructions to emulate_2op_SrcV_nobyte()
KVM: VMX: unlike vmcs on fail path
KVM: PPC: Emulator: clean up SPR reads and writes
KVM: PPC: Emulator: clean up instruction parsing
kvm/powerpc: Add new ioctl to retreive server MMU infos
kvm/book3s: Make kernel emulated H_PUT_TCE available for "PR" KVM
KVM: PPC: bookehv: Fix r8/r13 storing in level exception handler
KVM: PPC: Book3S: Enable IRQs during exit handling
KVM: PPC: Fix PR KVM on POWER7 bare metal
KVM: PPC: Fix stbux emulation
KVM: PPC: bookehv: Use lwz/stw instead of PPC_LL/PPC_STL for 32-bit fields
...
Pull timer updates from Thomas Gleixner.
Various trivial conflict fixups in arch Kconfig due to addition of
unrelated entries nearby. And one slightly more subtle one for sparc32
(new user of GENERIC_CLOCKEVENTS), fixed up as per Thomas.
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
timekeeping: Fix a few minor newline issues.
time: remove obsolete declaration
ntp: Fix a stale comment and a few stray newlines.
ntp: Correct TAI offset during leap second
timers: Fixup the Kconfig consolidation fallout
x86: Use generic time config
unicore32: Use generic time config
um: Use generic time config
tile: Use generic time config
sparc: Use: generic time config
sh: Use generic time config
score: Use generic time config
s390: Use generic time config
openrisc: Use generic time config
powerpc: Use generic time config
mn10300: Use generic time config
mips: Use generic time config
microblaze: Use generic time config
m68k: Use generic time config
m32r: Use generic time config
...
Pull fpu state cleanups from Ingo Molnar:
"This tree streamlines further aspects of FPU handling by eliminating
the prepare_to_copy() complication and moving that logic to
arch_dup_task_struct().
It also fixes the FPU dumps in threaded core dumps, removes and old
(and now invalid) assumption plus micro-optimizes the exit path by
avoiding an FPU save for dead tasks."
Fixed up trivial add-add conflict in arch/sh/kernel/process.c that came
in because we now do the FPU handling in arch_dup_task_struct() rather
than the legacy (and now gone) prepare_to_copy().
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, fpu: drop the fpu state during thread exit
x86, xsave: remove thread_has_fpu() bug check in __sanitize_i387_state()
coredump: ensure the fpu state is flushed for proper multi-threaded core dump
fork: move the real prepare_to_copy() users to arch_dup_task_struct()
Pull scheduler changes from Ingo Molnar:
"The biggest change is the cleanup/simplification of the load-balancer:
instead of the current practice of architectures twiddling scheduler
internal data structures and providing the scheduler domains in
colorfully inconsistent ways, we now have generic scheduler code in
kernel/sched/core.c:sched_init_numa() that looks at the architecture's
node_distance() parameters and (while not fully trusting it) deducts a
NUMA topology from it.
This inevitably changes balancing behavior - hopefully for the better.
There are various smaller optimizations, cleanups and fixlets as well"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Taint kernel with TAINT_WARN after sleep-in-atomic bug
sched: Remove stale power aware scheduling remnants and dysfunctional knobs
sched/debug: Fix printing large integers on 32-bit platforms
sched/fair: Improve the ->group_imb logic
sched/nohz: Fix rq->cpu_load[] calculations
sched/numa: Don't scale the imbalance
sched/fair: Revert sched-domain iteration breakage
sched/x86: Rewrite set_cpu_sibling_map()
sched/numa: Fix the new NUMA topology bits
sched/numa: Rewrite the CONFIG_NUMA sched domain support
sched/fair: Propagate 'struct lb_env' usage into find_busiest_group
sched/fair: Add some serialization to the sched_domain load-balance walk
sched/fair: Let minimally loaded cpu balance the group
sched: Change rq->nr_running to unsigned int
x86/numa: Check for nonsensical topologies on real hw as well
x86/numa: Hard partition cpu topology masks on node boundaries
x86/numa: Allow specifying node_distance() for numa=fake
x86/sched: Make mwait_usable() heed to "idle=" kernel parameters properly
sched: Update documentation and comments
sched_rt: Avoid unnecessary dequeue and enqueue of pushable tasks in set_cpus_allowed_rt()
Pull smp hotplug cleanups from Thomas Gleixner:
"This series is merily a cleanup of code copied around in arch/* and
not changing any of the real cpu hotplug horrors yet. I wish I'd had
something more substantial for 3.5, but I underestimated the lurking
horror..."
Fix up trivial conflicts in arch/{arm,sparc,x86}/Kconfig and
arch/sparc/include/asm/thread_info_32.h
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
um: Remove leftover declaration of alloc_task_struct_node()
task_allocator: Use config switches instead of magic defines
sparc: Use common threadinfo allocator
score: Use common threadinfo allocator
sh-use-common-threadinfo-allocator
mn10300: Use common threadinfo allocator
powerpc: Use common threadinfo allocator
mips: Use common threadinfo allocator
hexagon: Use common threadinfo allocator
m32r: Use common threadinfo allocator
frv: Use common threadinfo allocator
cris: Use common threadinfo allocator
x86: Use common threadinfo allocator
c6x: Use common threadinfo allocator
fork: Provide kmemcache based thread_info allocator
tile: Use common threadinfo allocator
fork: Provide weak arch_release_[task_struct|thread_info] functions
fork: Move thread info gfp flags to header
fork: Remove the weak insanity
sh: Remove cpu_idle_wait()
...
Sigh, I missed to check which architecture Kconfig files actually
include the core Kconfig file. There are a few which did not. So we
broke them.
Instead of adding the includes to those, we are better off to move the
include to init/Kconfig like we did already with irqs and others.
This does not change anything for the architectures using the old
style periodic timer mode. It just solves the build wreckage there.
For those architectures which use the clock events infrastructure it
moves the include of the core Kconfig file to "General setup" which is
a way more logical place than having it at random locations specified
by the architecture specific Kconfigs.
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Anna-Maria Gleixner <anna-maria@glx-um.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some discussion with the glibc mailing lists revealed that this was
necessary for 64-bit platforms with MIPS-like sign-extension rules
for 32-bit values. The original symptom was that passing (uid_t)-1 to
setreuid() was failing in programs linked -pthread because of the "setxid"
mechanism for passing setxid-type function arguments to the syscall code.
SYSCALL_WRAPPERS handles ensuring that all syscall arguments end up with
proper sign-extension and is thus the appropriate fix for this problem.
On other platforms (s390, powerpc, sparc64, and mips) this was fixed
in 2.6.28.6. The general issue is tracked as CVE-2009-0029.
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Historical prepare_to_copy() is mostly a no-op, duplicated for majority of
the architectures and the rest following the x86 model of flushing the extended
register state like fpu there.
Remove it and use the arch_dup_task_struct() instead.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1336692811-30576-1-git-send-email-suresh.b.siddha@intel.com
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This passes siginfo and mcontext to tilegx32 signal handlers that
don't have SA_SIGINFO set just as we have been doing for tilegx64.
Cc: stable@vger.kernel.org
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
First, we were at risk of handling thread-info flags, in particular
do_signal(), when returning from kernel space. This could happen
after a failed kernel_execve(), or when forking a kernel thread.
The fix is to test in do_work_pending() for user_mode() and return
immediately if so; we already had this test for one of the flags,
so I just hoisted it to the top of the function.
Second, if a ptraced process updated the callee-saved registers
in the ptregs struct and then processed another thread-info flag, we
would overwrite the modifications with the original callee-saved
registers. To fix this, we add a register to note if we've already
saved the registers once, and skip doing it on additional passes
through the loop. To avoid a performance hit from the couple of
extra instructions involved, I modified the GET_THREAD_INFO() macro
to be guaranteed to be one instruction, then bundled it with adjacent
instructions, yielding an overall net savings.
Reported-By: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The current code groups up to 16 nodes in a level and then puts an
ALLNODES domain spanning the entire tree on top of that. This doesn't
reflect the numa topology and esp for the smaller not-fully-connected
machines out there today this might make a difference.
Therefore, build a proper numa topology based on node_distance().
Since there's no fixed numa layers anymore, the static SD_NODE_INIT
and SD_ALLNODES_INIT aren't usable anymore, the new code tries to
construct something similar and scales some values either on the
number of cpus in the domain and/or the node_distance() ratio.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: linux-alpha@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-sh@vger.kernel.org
Cc: Matt Turner <mattst88@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: sparclinux@vger.kernel.org
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Greg Pearson <greg.pearson@hp.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: bob.picco@oracle.com
Cc: chris.mason@oracle.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-r74n3n8hhuc2ynbrnp3vt954@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Same code. Use the generic version. The special Makefile treatment is
pointless anyway as init_task.o contains only data which is handled by
the linker script. So no point on being treated like head text.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Link: http://lkml.kernel.org/r/20120503085035.528129988@linutronix.de
Preparatory patch to make the idle thread allocation for secondary
cpus generic.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20120420124556.964170564@linutronix.de
This continues the theme started with vm_brk() and vm_munmap():
vm_mmap() does the same thing as do_mmap(), but additionally does the
required VM locking.
This uninlines (and rewrites it to be clearer) do_mmap(), which sadly
duplicates it in mm/mmap.c and mm/nommu.c. But that way we don't have
to export our internal do_mmap_pgoff() function.
Some day we hopefully don't have to export do_mmap() either, if all
modular users can become the simpler vm_mmap() instead. We're actually
very close to that already, with the notable exception of the (broken)
use in i810, and a couple of stragglers in binfmt_elf.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge reason: development work has dependency on kvm patches merged
upstream.
Conflicts:
Documentation/feature-removal-schedule.txt
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Until we push the unaligned access support for tilegx, it's silly
to have arch/tile/kernel/proc.c generate a warning about an unused
variable. Extend the #ifdef to cover all the code and data for now.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The scheduler depends on receiving the CPU_STARTING notification, without
which we end up into a lot of trouble. So add the missing call to
notify_cpu_starting() in the bringup code.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
When a host stops or suspends a VM it will set a flag to show this. The
watchdog will use these functions to determine if a softlockup is real, or the
result of a suspended VM.
Signed-off-by: Eric B Munson <emunson@mgebm.net>
asm-generic changes Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Pull arch/tile bug fixes from Chris Metcalf:
"This includes Paul Gortmaker's change to fix the <asm/system.h>
disintegration issues on tile, a fix to unbreak the tilepro ethernet
driver, and a backlog of bugfix-only changes from internal Tilera
development over the last few months.
They have all been to LKML and on linux-next for the last few days.
The EDAC change to MAINTAINERS is an oddity but discussion on the
linux-edac list suggested I ask you to pull that change through my
tree since they don't have a tree to pull edac changes from at the
moment."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (39 commits)
drivers/net/ethernet/tile: fix netdev_alloc_skb() bombing
MAINTAINERS: update EDAC information
tilepro ethernet driver: fix a few minor issues
tile-srom.c driver: minor code cleanup
edac: say "TILEGx" not "TILEPro" for the tilegx edac driver
arch/tile: avoid accidentally unmasking NMI-type interrupt accidentally
arch/tile: remove bogus performance optimization
arch/tile: return SIGBUS for addresses that are unaligned AND invalid
arch/tile: fix finv_buffer_remote() for tilegx
arch/tile: use atomic exchange in arch_write_unlock()
arch/tile: stop mentioning the "kvm" subdirectory
arch/tile: export the page_home() function.
arch/tile: fix pointer cast in cacheflush.c
arch/tile: fix single-stepping over swint1 instructions on tilegx
arch/tile: implement panic_smp_self_stop()
arch/tile: add "nop" after "nap" to help GX idle power draw
arch/tile: use proper memparse() for "maxmem" options
arch/tile: fix up locking in pgtable.c slightly
arch/tile: don't leak kernel memory when we unload modules
arch/tile: fix bug in delay_backoff()
...
The return path as we reload registers and core state requires that r30
hold a boolean indicating whether we are returning from an NMI, but in a
couple of cases we weren't setting this properly, with the result that we
could accidentally unmask the NMI interrupt(s), which could cause confusion.
Now we set r30 in every place where we jump into the interrupt return path.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We were re-homing the initial task's kernel stack on the boot cpu,
but in fact it's better to let it stay globally homed, since that
task isn't bound to the boot cpu anyway. This is more of a general
cleanup than an actual performance optimization, but it removes
code, which is a good thing. :-)
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Previously we were returning SIGSEGV in this case. It seems cleaner
to return SIGBUS since the hardware figures out alignment traps
before TLB violations, so SIGBUS is the "more correct" signal.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
There were some correctness issues with this code that are now fixed
with this change. The change is likely less performant than it could
be, but it should no longer be vulnerable to any races with memory
operations on the memory network while invalidating a range of memory.
This code is run infrequently so performance isn't critical, but
correctness definitely is.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This idiom is used elsewhere when we do an unlock by writing a zero,
but I missed it here. Using an atomic operation avoids waiting
on the write buffer for the unlocking write to be sent to the home cache.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
It causes "make clean" to fail, for example. Once we have KVM support
complete, we'll reinstate the subdir reference.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Pragmatically it couldn't be wrong to cast pointers to long to compare
them (since all kernel addresses are in the top half of VA space),
but it's more correct to cast to unsigned long.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
If we are single-stepping and make a syscall, we call ptrace_notify()
explicitly on the return path back to user space, since we are returning
to a pc value set artificially to the next instruction, and otherwise
we won't register that we stepped over the syscall instruction (swint1).
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This allows the later-panicking tiles to wait in a lower power state
until they get interrupted with an smp_send_stop().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We should be holding the init_mm.page_table_lock in shatter_huge_page()
since we are modifying the kernel page tables. Then, only if we are
walking the other root page tables to update them, do we want to take
the pgd_lock.
Add a comment about taking the pgd_lock that we always do it with
interrupts disabled and therefore are not at risk from the tlbflush
IPI deadlock as is seen on x86.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We were carefully computing a value to use for the number of loops
to spin for, and then ignoring it.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Previously we only handled kernels up to a single huge page in size.
Now we create additional PTEs appropriately.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
If we took a page fault while we had interrupts disabled, we
shouldn't enable them in the page fault handler.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We make sure not to try to set the home for an MMIO PTE (on tilegx)
or a PTE that isn't referencing memory managed by Linux.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Doing so raises the possibility of self-deadlock if we are waiting
for a backtrace for an oprofile or perf interrupt while we are
in the middle of migrating our own stack page.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Not associated with any code changes, so I'm just lumping these
comment changes into a commit by themselves.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We now respond to MEM_ERROR traps (e.g. an atomic instruction to
non-cacheable memory) with a SIGBUS.
We also no longer generate a console crash message if a user
process die due to a SIGTRAP.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
In certain circumstances we need to do a bunch of jump-and-link
instructions to fill the hardware return-address stack with nonzero values.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Fix a long-standing bug in the stack backtracer where we would print
garbage to the console instead of kernel function names, if the kernel
wasn't built with symbol support (e.g. mboot).
Make sure to tag every line of userspace backtrace output if we actually
have the mmap_sem, since that way if there's no tag, we know that it's
because we couldn't trylock the semaphore.
Stop doing a TLB flush and examining page tables during backtrace.
Instead, just trust that __copy_from_user_inatomic() will properly fault
and return a failure, which it should do in all cases.
Fix a latent bug where the backtracer would directly examine a signal
context in user space, rather than copying it safely to kernel memory
first. This meant that a race with another thread could potentially
have caused a kernel panic.
Guard against unaligned sp when trying to restart backtrace at an
interrupt or signal handler point in the kernel backtracer.
Report kernel symbolic information for the call instruction rather
than for the following instruction. We still report the actual numeric
address corresponding to the instruction after the call, for the sake
of consistency with the normal expectations for stack backtracers.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Add a comment explaining why this is important, and add a CFLAGS_REMOVE
clause to the Makefile to make sure it happens.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
With lockstat we can end up trying to get a backtrace before
"high_memory" is initialized, so don't worry about range testing
if it is zero.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
It still returns whether @v was not @u, not the old value,
unlike __atomic_add_unless().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arun Sharma <asharma@fb.com>
We aren't yet using this definition in the kernel, but fix it up
before someone goes looking for it.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Commit bd119c6923
"Disintegrate asm/system.h for Tile"
created the asm/switch_to.h file, but did not add an include
of it to all its users.
Also, commit b4816afa39
"Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h"
introduced the concept of asm/cmpxchg.h but the tile arch
never got one. Fork the cmpxchg content out of the asm/atomic.h
file to create one.
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=W59/
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/rustyrussell/linux
Pull cpumask cleanups from Rusty Russell:
"(Somehow forgot to send this out; it's been sitting in linux-next, and
if you don't want it, it can sit there another cycle)"
I'm a sucker for things that actually delete lines of code.
Fix up trivial conflict in arch/arm/kernel/kprobes.c, where Rusty fixed
a user of &cpu_online_map to be cpu_online_mask, but that code got
deleted by commit b21d55e98a ("ARM: 7332/1: extract out code patch
function from kprobes").
* tag 'for-linus' of git://github.com/rustyrussell/linux:
cpumask: remove old cpu_*_map.
documentation: remove references to cpu_*_map.
drivers/cpufreq/db8500-cpufreq: remove references to cpu_*_map.
remove references to cpu_*_map in arch/
Pull arch/tile (really asm-generic) update from Chris Metcalf:
"These are a couple of asm-generic changes that apply to tile."
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
compat: use sys_sendfile64() implementation for sendfile syscall
[PATCH v3] ipc: provide generic compat versions of IPC syscalls
This has been obsolescent for a while; time for the final push.
In adjacent context, replaced old cpus_* with cpumask_*.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: David S. Miller <davem@davemloft.net> (arch/sparc)
Acked-by: Chris Metcalf <cmetcalf@tilera.com> (arch/tile)
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: linux-hexagon@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: sparclinux@vger.kernel.org
Merge third batch of patches from Andrew Morton:
- Some MM stragglers
- core SMP library cleanups (on_each_cpu_mask)
- Some IPI optimisations
- kexec
- kdump
- IPMI
- the radix-tree iterator work
- various other misc bits.
"That'll do for -rc1. I still have ~10 patches for 3.4, will send
those along when they've baked a little more."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (35 commits)
backlight: fix typo in tosa_lcd.c
crc32: add help text for the algorithm select option
mm: move hugepage test examples to tools/testing/selftests/vm
mm: move slabinfo.c to tools/vm
mm: move page-types.c from Documentation to tools/vm
selftests/Makefile: make `run_tests' depend on `all'
selftests: launch individual selftests from the main Makefile
radix-tree: use iterators in find_get_pages* functions
radix-tree: rewrite gang lookup using iterator
radix-tree: introduce bit-optimized iterator
fs/proc/namespaces.c: prevent crash when ns_entries[] is empty
nbd: rename the nbd_device variable from lo to nbd
pidns: add reboot_pid_ns() to handle the reboot syscall
sysctl: use bitmap library functions
ipmi: use locks on watchdog timeout set on reboot
ipmi: simplify locking
ipmi: fix message handling during panics
ipmi: use a tasklet for handling received messages
ipmi: increase KCS timeouts
ipmi: decrease the IPMI message transaction time in interrupt mode
...
We have lots of infrastructure in place to partition multi-core systems
such that we have a group of CPUs that are dedicated to specific task:
cgroups, scheduler and interrupt affinity, and cpuisol= boot parameter.
Still, kernel code will at times interrupt all CPUs in the system via IPIs
for various needs. These IPIs are useful and cannot be avoided
altogether, but in certain cases it is possible to interrupt only specific
CPUs that have useful work to do and not the entire system.
This patch set, inspired by discussions with Peter Zijlstra and Frederic
Weisbecker when testing the nohz task patch set, is a first stab at trying
to explore doing this by locating the places where such global IPI calls
are being made and turning the global IPI into an IPI for a specific group
of CPUs. The purpose of the patch set is to get feedback if this is the
right way to go for dealing with this issue and indeed, if the issue is
even worth dealing with at all. Based on the feedback from this patch set
I plan to offer further patches that address similar issue in other code
paths.
This patch creates an on_each_cpu_mask() and on_each_cpu_cond()
infrastructure API (the former derived from existing arch specific
versions in Tile and Arm) and uses them to turn several global IPI
invocation to per CPU group invocations.
Core kernel:
on_each_cpu_mask() calls a function on processors specified by cpumask,
which may or may not include the local processor.
You must not call this function with disabled interrupts or from a
hardware interrupt handler or from a bottom half handler.
arch/arm:
Note that the generic version is a little different then the Arm one:
1. It has the mask as first parameter
2. It calls the function on the calling CPU with interrupts disabled,
but this should be OK since the function is called on the other CPUs
with interrupts disabled anyway.
arch/tile:
The API is the same as the tile private one, but the generic version
also calls the function on the with interrupts disabled in UP case
This is OK since the function is called on the other CPUs
with interrupts disabled.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Sasha Levin <levinsasha928@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Avi Kivity <avi@redhat.com>
Acked-by: Michal Nazarewicz <mina86@mina86.org>
Cc: Kosaki Motohiro <kosaki.motohiro@gmail.com>
Cc: Milton Miller <miltonm@bga.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAT3NKzROxKuMESys7AQKElw/+JyDxJSlj+g+nymkx8IVVuU8CsEwNLgRk
8KEnRfLhGtkXFLSJYWO6jzGo16F8Uqli1PdMFte/wagSv0285/HZaKlkkBVHdJ/m
u40oSjgT013bBh6MQ0Oaf8pFezFUiQB5zPOA9QGaLVGDLXCmgqUgd7exaD5wRIwB
ZmyItjZeAVnDfk1R+ZiNYytHAi8A5wSB+eFDCIQYgyulA1Igd1UnRtx+dRKbvc/m
rWQ6KWbZHIdvP1ksd8wHHkrlUD2pEeJ8glJLsZUhMm/5oMf/8RmOCvmo8rvE/qwl
eDQ1h4cGYlfjobxXZMHqAN9m7Jg2bI946HZjdb7/7oCeO6VW3FwPZ/Ic75p+wp45
HXJTItufERYk6QxShiOKvA+QexnYwY0IT5oRP4DrhdVB/X9cl2MoaZHC+RbYLQy+
/5VNZKi38iK4F9AbFamS7kd0i5QszA/ZzEzKZ6VMuOp3W/fagpn4ZJT1LIA3m4A9
Q0cj24mqeyCfjysu0TMbPtaN+Yjeu1o1OFRvM8XffbZsp5bNzuTDEvviJ2NXw4vK
4qUHulhYSEWcu9YgAZXvEWDEM78FXCkg2v/CrZXH5tyc95kUkMPcgG+QZBB5wElR
FaOKpiC/BuNIGEf02IZQ4nfDxE90QwnDeoYeV+FvNj9UEOopJ5z5bMPoTHxm4cCD
NypQthI85pc=
=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
The motivation for this patchset was that I was looking at a way for a
qemu-kvm process, to exclude the guest memory from its core dump, which
can be quite large. There are already a number of filter flags in
/proc/<pid>/coredump_filter, however, these allow one to specify 'types'
of kernel memory, not specific address ranges (which is needed in this
case).
Since there are no more vma flags available, the first patch eliminates
the need for the 'VM_ALWAYSDUMP' flag. The flag is used internally by
the kernel to mark vdso and vsyscall pages. However, it is simple
enough to check if a vma covers a vdso or vsyscall page without the need
for this flag.
The second patch then replaces the 'VM_ALWAYSDUMP' flag with a new
'VM_NODUMP' flag, which can be set by userspace using new madvise flags:
'MADV_DONTDUMP', and unset via 'MADV_DODUMP'. The core dump filters
continue to work the same as before unless 'MADV_DONTDUMP' is set on the
region.
The qemu code which implements this features is at:
http://people.redhat.com/~jbaron/qemu-dump/qemu-dump.patch
In my testing the qemu core dump shrunk from 383MB -> 13MB with this
patch.
I also believe that the 'MADV_DONTDUMP' flag might be useful for
security sensitive apps, which might want to select which areas are
dumped.
This patch:
The VM_ALWAYSDUMP flag is currently used by the coredump code to
indicate that a vma is part of a vsyscall or vdso section. However, we
can determine if a vma is in one these sections by checking it against
the gate_vma and checking for a non-NULL return value from
arch_vma_name(). Thus, freeing a valuable vma bit.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull kmap_atomic cleanup from Cong Wang.
It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().
Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.
* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
drbd: remove the second argument of k[un]map_atomic()
zcache: remove the second argument of k[un]map_atomic()
gma500: remove the second argument of k[un]map_atomic()
dm: remove the second argument of k[un]map_atomic()
tomoyo: remove the second argument of k[un]map_atomic()
sunrpc: remove the second argument of k[un]map_atomic()
rds: remove the second argument of k[un]map_atomic()
net: remove the second argument of k[un]map_atomic()
mm: remove the second argument of k[un]map_atomic()
lib: remove the second argument of k[un]map_atomic()
power: remove the second argument of k[un]map_atomic()
kdb: remove the second argument of k[un]map_atomic()
udf: remove the second argument of k[un]map_atomic()
ubifs: remove the second argument of k[un]map_atomic()
squashfs: remove the second argument of k[un]map_atomic()
reiserfs: remove the second argument of k[un]map_atomic()
ocfs2: remove the second argument of k[un]map_atomic()
ntfs: remove the second argument of k[un]map_atomic()
...
Pull scheduler changes for v3.4 from Ingo Molnar
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
printk: Make it compile with !CONFIG_PRINTK
sched/x86: Fix overflow in cyc2ns_offset
sched: Fix nohz load accounting -- again!
sched: Update yield() docs
printk/sched: Introduce special printk_sched() for those awkward moments
sched/nohz: Correctly initialize 'next_balance' in 'nohz' idle balancer
sched: Cleanup cpu_active madness
sched: Fix load-balance wreckage
sched: Clean up parameter passing of proc_sched_autogroup_set_nice()
sched: Ditch per cgroup task lists for load-balancing
sched: Rename load-balancing fields
sched: Move load-balancing arguments into helper struct
sched/rt: Do not submit new work when PI-blocked
sched/rt: Prevent idle task boosting
sched/wait: Add __wake_up_all_locked() API
sched/rt: Document scheduler related skip-resched-check sites
sched/rt: Use schedule_preempt_disabled()
sched/rt: Add schedule_preempt_disabled()
sched/rt: Do not throttle when PI boosting
sched/rt: Keep period timer ticking when rt throttling is active
...
[swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
When using the "compat" APIs, architectures will generally want to
be able to make direct syscalls to msgsnd(), shmctl(), etc., and
in the kernel we would want them to be handled directly by
compat_sys_xxx() functions, as is true for other compat syscalls.
However, for historical reasons, several of the existing compat IPC
syscalls do not do this. semctl() expects a pointer to the fourth
argument, instead of the fourth argument itself. msgsnd(), msgrcv()
and shmat() expect arguments in different order.
This change adds an ARCH_WANT_OLD_COMPAT_IPC config option that can be
set to preserve this behavior for ports that use it (x86, sparc, powerpc,
s390, and mips). No actual semantics are changed for those architectures,
and there is only a minimal amount of code refactoring in ipc/compat.c.
Newer architectures like tile (and perhaps future architectures such
as arm64 and unicore64) should not select this option, and thus can
avoid having any IPC-specific code at all in their architecture-specific
compat layer. In the same vein, if this option is not selected, IPC_64
mode is assumed, since that's what the <asm-generic> headers expect.
The workaround code in "tile" for msgsnd() and msgrcv() is removed
with this change; it also fixes the bug that shmat() and semctl() were
not being properly handled.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
As described in e6fa16ab ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block
is pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this
code wrong, so using this helper function should stop that from
happening again.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This was inspired by mchehab@redhat.com's observation that we
didn't have EDAC configured on by default in both files. In addition,
we were setting INITRAMFS_SOURCE to a non-empty string, which isn't
a very common default and required editing to do test builds.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This was Kay Siever's bombing to convert 'cpu' to a regular subsystem.
The change left a bogus second argument to sysfs_create_file().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
* 'for-next' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: Split trivial #if defined(__KERNEL__) && X conditionals
UAPI: Don't have a #elif clause in a __KERNEL__ guard in linux/soundcard.h
UAPI: Fix AHZ multiple inclusion when __KERNEL__ is removed
UAPI: Make linux/patchkey.h easier to parse
UAPI: Fix nested __KERNEL__ guards in video/edid.h
UAPI: Alter the S390 asm include guards to be recognisable by the UAPI splitter
UAPI: Guard linux/cuda.h
UAPI: Guard linux/pmu.h
UAPI: Guard linux/isdn_divertif.h
UAPI: Guard linux/sound.h
UAPI: Rearrange definition of HZ in asm-generic/param.h
UAPI: Make FRV use asm-generic/param.h
UAPI: Make M32R use asm-generic/param.h
UAPI: Make MN10300 use asm-generic/param.h
UAPI: elf_read_implies_exec() is a kernel-only feature - so hide from userspace
UAPI: Don't include linux/compat.h in sparc's asm/siginfo.h
UAPI: Fix arch/mips/include/asm/Kbuild to have separate header-y lines
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (80 commits)
x86/PCI: Expand the x86_msi_ops to have a restore MSIs.
PCI: Increase resource array mask bit size in pcim_iomap_regions()
PCI: DEVICE_COUNT_RESOURCE should be equal to PCI_NUM_RESOURCES
PCI: pci_ids: add device ids for STA2X11 device (aka ConneXT)
PNP: work around Dell 1536/1546 BIOS MMCONFIG bug that breaks USB
x86/PCI: amd: factor out MMCONFIG discovery
PCI: Enable ATS at the device state restore
PCI: msi: fix imbalanced refcount of msi irq sysfs objects
PCI: kconfig: English typo in pci/pcie/Kconfig
PCI/PM/Runtime: make PCI traces quieter
PCI: remove pci_create_bus()
xtensa/PCI: convert to pci_scan_root_bus() for correct root bus resources
x86/PCI: convert to pci_create_root_bus() and pci_scan_root_bus()
x86/PCI: use pci_scan_bus() instead of pci_scan_bus_parented()
x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan
sparc32, leon/PCI: convert to pci_scan_root_bus() for correct root bus resources
sparc/PCI: convert to pci_create_root_bus()
sh/PCI: convert to pci_scan_root_bus() for correct root bus resources
powerpc/PCI: convert to pci_create_root_bus()
powerpc/PCI: split PHB part out of pcibios_map_io_space()
...
Fix up conflicts in drivers/pci/msi.c and include/linux/pci_regs.h due
to the same patches being applied in other branches.
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPBZXBAAoJECgfDbjSjVRpuuYIAIMD0wE96MuTOSBJX4VG8VAP
UyjL9dsfMRy8CKioQo5/fxpTY07YBCWmNauSSX7pzgcoUKBfYIGn4Z1qwGYsWK9M
CzLs6PXLTugw0FtKobHZl/klRTWEBS6YOUjp9x568rplwF+Ppk7b993uj7eS/g+e
T0mUKzqg4/UavbHd9+W5KgC4drQ5hgtu2WZHoUxBK4umnd3C2G+U82Sthg50o/XU
SC8IGm39K8I36HoIWgXj3Y7nkOP3mQELohOT4ZPiVSmLvGS4i47+ix75anO+8ZvZ
jxHr8RC85IK1Nd89NZhbKOyvx0QQiwoKUZaTwcWXJNSOADzZnM6icdIsodc+Elo=
=ccQZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
lib: use generic pci_iomap on all architectures
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
alpha: drop pci_iomap/pci_iounmap from pci-noop.c
mn10300: switch to GENERIC_PCI_IOMAP
mn10300: add missing __iomap markers
frv: switch to GENERIC_PCI_IOMAP
tile: switch to GENERIC_PCI_IOMAP
tile: don't panic on iomap
sparc: switch to GENERIC_PCI_IOMAP
sh: switch to GENERIC_PCI_IOMAP
powerpc: switch to GENERIC_PCI_IOMAP
parisc: switch to GENERIC_PCI_IOMAP
mips: switch to GENERIC_PCI_IOMAP
microblaze: switch to GENERIC_PCI_IOMAP
arm: switch to GENERIC_PCI_IOMAP
alpha: switch to GENERIC_PCI_IOMAP
lib: add GENERIC_PCI_IOMAP
lib: move GENERIC_IOMAP to lib/Kconfig
Fix up trivial conflicts due to changes nearby in arch/{m68k,score}/Kconfig
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
This patch converts TILE's architecture-specific 'pcibios_set_master()'
routine to a non-inlined function. This will allow follow on patches
to create a generic 'pcibios_set_master()' function using the '__weak'
attribute which can be used by all architectures as a default which,
if necessary, can then be over-ridden by architecture-specific code.
Converting 'pci_bios_set_master()' to a non-inlined function will
allow TILE's 'pcibios_set_master()' implementation to remain
architecture-specific after the generic version is introduced and
thus, not change current behavior.
No functional change.
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the 'cpu sysdev_class' over to a regular 'cpu' subsystem
and converts the devices to regular devices. The sysdev drivers are
implemented as subsystem interfaces now.
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Userspace relies on events and generic sysfs subsystem infrastructure
from sysdev devices, which are made available with this conversion.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Len Brown <lenb@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Those two APIs were provided to optimize the calls of
tick_nohz_idle_enter() and rcu_idle_enter() into a single
irq disabled section. This way no interrupt happening in-between would
needlessly process any RCU job.
Now we are talking about an optimization for which benefits
have yet to be measured. Let's start simple and completely decouple
idle rcu and dyntick idle logics to simplify.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Change from direct comparison of ->pid with zero to is_idle_task().
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
It is assumed that rcu won't be used once we switch to tickless
mode and until we restart the tick. However this is not always
true, as in x86-64 where we dereference the idle notifiers after
the tick is stopped.
To prepare for fixing this, add two new APIs:
tick_nohz_idle_enter_norcu() and tick_nohz_idle_exit_norcu().
If no use of RCU is made in the idle loop between
tick_nohz_enter_idle() and tick_nohz_exit_idle() calls, the arch
must instead call the new *_norcu() version such that the arch doesn't
need to call rcu_idle_enter() and rcu_idle_exit().
Otherwise the arch must call tick_nohz_enter_idle() and
tick_nohz_exit_idle() and also call explicitly:
- rcu_idle_enter() after its last use of RCU before the CPU is put
to sleep.
- rcu_idle_exit() before the first use of RCU after the CPU is woken
up.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The tick_nohz_stop_sched_tick() function, which tries to delay
the next timer tick as long as possible, can be called from two
places:
- From the idle loop to start the dytick idle mode
- From interrupt exit if we have interrupted the dyntick
idle mode, so that we reprogram the next tick event in
case the irq changed some internal state that requires this
action.
There are only few minor differences between both that
are handled by that function, driven by the ts->inidle
cpu variable and the inidle parameter. The whole guarantees
that we only update the dyntick mode on irq exit if we actually
interrupted the dyntick idle mode, and that we enter in RCU extended
quiescent state from idle loop entry only.
Split this function into:
- tick_nohz_idle_enter(), which sets ts->inidle to 1, enters
dynticks idle mode unconditionally if it can, and enters into RCU
extended quiescent state.
- tick_nohz_irq_exit() which only updates the dynticks idle mode
when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called).
To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed
into tick_nohz_idle_exit().
This simplifies the code and micro-optimize the irq exit path (no need
for local_irq_save there). This also prepares for the split between
dynticks and rcu extended quiescent state logics. We'll need this split to
further fix illegal uses of RCU in extended quiescent states in the idle
loop.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
tile now has working stubs for ioport_map and ioremap
such that the generic pci_iomap will DTRT: cast to
pointer on memory and return NULL and log message on IO map.
Switch it over to GENERIC_PCI_IOMAP.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
I think panic on iomap is there just for debugging.
If we return NULL instead, the generic pci_iomap will
DTRT so we don't need to roll our own.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We provided very similar routines internally, but now we can hook
into the generic framework by supplying our routines as function
pointers in the irq_chip structure instead.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
When freeing the page with this API, the page was "put" twice.
This was only discovered bringing up an MPT fusion controller, which
actually used the API; it hadn't been invoked previously, so the bug
had gone unnoticed.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The empty_zero_page[] export is required for ZERO_PAGE() module references.
The #includes are due to changes in implicit inclusion, and should of
course have been in the sources from the beginning.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
* 'for-linus' of git://github.com/cmetcalf-tilera/linux-tile:
arch/tile: factor out <arch/opcode.h> header
arch/tile: add the <arch> headers to the set of installed kernel headers
arch/tile: avoid exporting a symbol no longer used by gcc
arch/tile: avoid ISO namespace pollution with <asm/sigcontext.h>
The kernel code was using some <asm> headers that included a mix
of hardware-specific information (typically found in Tilera <arch>
headers) and structures, enums, and function declarations supporting
the disassembly function of the tile-desc.c sources.
This change refactors that code so that a hardware-specific, but
OS- and application-agnostic header, is created: <arch/opcode.h>.
This header is then exported to userspace along with the other
<arch> headers and can be used to build userspace code; in particular,
it is used by glibc as part of implementing the backtrace() function.
The new header, together with a header that specifically describes
the disassembly code (<asm/tile-desc.h> with _32 and _64 variants),
replaces the old <asm/opcode-tile*.h> and <asm/opcode_constants*.h>
headers.
As part of this change, we are also renaming the 32-bit constants
from TILE_xxx to TILEPRO_xxx to better reflect the fact that they
are specific to the TILEPro architecture, and not to TILE-Gx
and any successor "tile" architecture chips.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
These headers are similar to the <asm> headers that describe kernel
APIs, but instead describe aspects of the actual hardware in an
OS- and application-independent manner. We need to include them in
the set of installed headers so that userspace tools (including glibc)
can build purely from the provided kernel headers.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
An earlier Tilera compiler generated calls to an "__ll_mul"
function for long long multiplication. Our libgcc supported that
as an alias for the normal __muldi3 routine, so we made it available
to kernel modules as well. However, for a while now the compiler
has internally been generating only the standard __muldi3 symbol,
and the version we are giving back to the community does not have
the __ll_mul alias, so we are removing it from the kernel too.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
<asm/sigcontext.h> is used by glibc's <bits/sigcontext.h> from <signal.h>,
which means that it can't clutter the namespace with random symbols
or #defines. However, we use <arch/abi.h> to get a suitable type to
hold a machine register.
This change makes <arch/abi.h> safe to use in this kind of context
if __need_int_reg_t is defined prior to including the file; in that
case, it only defines a few symbols that are safe in the ISO namespace
(prefixed with double underscores). <asm/sigcontext.h> then uses
the __uint_reg_t type instead of the normal uint_reg_t.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
time, s390: Get rid of compile warning
dw_apb_timer: constify clocksource name
time: Cleanup old CONFIG_GENERIC_TIME references that snuck in
time: Change jiffies_to_clock_t() argument type to unsigned long
alarmtimers: Fix error handling
clocksource: Make watchdog reset lockless
posix-cpu-timers: Cure SMP accounting oddities
s390: Use direct ktime path for s390 clockevent device
clockevents: Add direct ktime programming function
clockevents: Make minimum delay adjustments configurable
nohz: Remove "Switched to NOHz mode" debugging messages
proc: Consider NO_HZ when printing idle and iowait times
nohz: Make idle/iowait counter update conditional
nohz: Fix update_ts_time_stat idle accounting
cputime: Clean up cputime_to_usecs and usecs_to_cputime macros
alarmtimers: Rework RTC device selection using class interface
alarmtimers: Add try_to_cancel functionality
alarmtimers: Add more refined alarm state tracking
alarmtimers: Remove period from alarm structure
alarmtimers: Remove interval cap limit hack
...
The 32-bit TILEPro support uses some #defines in <asm/atomic_32.h>
for atomic support routines in assembly. To make this more explicit,
I've turned those includes into includes of <asm/atomic_32.h>, which
should hopefully make it clear that they shouldn't be bombed into
<linux/atomic.h> in any cleanups.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Awhile back I removed all the CONFIG_GENERIC_TIME referecnes as
the last of the non-GENERIC_TIME arches were converted.
However, due to the functionality being important and around for
awhile, there apparently were some out of tree hardware enablement
patches that used it and have since been merged.
This patch removes the remaining instances of GENERIC_TIME.
Singed-off-by: John Stultz <john.stultz@linaro.org>
* 'apei-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI, APEI, EINJ Param support is disabled by default
APEI GHES: 32-bit buildfix
ACPI: APEI build fix
ACPI, APEI, GHES: Add hardware memory error recovery support
HWPoison: add memory_failure_queue()
ACPI, APEI, GHES, Error records content based throttle
ACPI, APEI, GHES, printk support for recoverable error via NMI
lib, Make gen_pool memory allocator lockless
lib, Add lock-less NULL terminated single list
Add Kconfig option ARCH_HAVE_NMI_SAFE_CMPXCHG
ACPI, APEI, Add WHEA _OSC support
ACPI, APEI, Add APEI bit support in generic _OSC call
ACPI, APEI, GHES, Support disable GHES at boot time
ACPI, APEI, GHES, Prevent GHES to be built as module
ACPI, APEI, Use apei_exec_run_optional in APEI EINJ and ERST
ACPI, APEI, Add apei_exec_run_optional
ACPI, APEI, GHES, Do not ratelimit fatal error printk before panic
ACPI, APEI, ERST, Fix erst-dbg long record reading issue
ACPI, APEI, ERST, Prevent erst_dbg from loading if ERST is disabled
Some trivial conflicts due to other various merges
adding to the end of common lists sooner than this one.
arch/ia64/Kconfig
arch/powerpc/Kconfig
arch/x86/Kconfig
lib/Kconfig
lib/Makefile
Signed-off-by: Len Brown <len.brown@intel.com>
