For the YUV conversion to work properly, ->x_scaling[1] should never
be set to VC4_SCALING_NONE, but vc4_get_scaling_mode() might return
VC4_SCALING_NONE if the horizontal scaling ratio exactly matches the
horizontal subsampling factor. Add a test to turn VC4_SCALING_NONE
into VC4_SCALING_PPF when that happens.
The old ->x_scaling[0] adjustment is dropped as I couldn't find any
mention to this constraint in the spec and it's proven to be
unnecessary (I tested various multi-planar YUV formats with scaling
disabled, and all of them worked fine without this adjustment).
Fixes: fc04023faf ("drm/vc4: Add support for YUV planes.")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109102633.32603-1-boris.brezillon@bootlin.com
Some panels need an active-low data enable (DE) signal for the RGB
interface. This requires flipping a bit in the TCON0 polarity register
when setting up the mode for the RGB interface.
Match the associated bus flag and use it to set the polarity inversion
bit for the DE signal when required.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-4-contact@paulk.fr
Features such as dithering and pixel data edge configuration currently
rely on the panel registered with the TCON driver. However, bridges are
also supported in addition to panels for RGB setup.
Instead of retrieving the connector from the panel, get it from the
encoder with the dedicated helper.
Even in the case of bridges, the connector is registered with the
encoder from our driver and is accessible when iterating connectors.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-3-contact@paulk.fr
Passing the encoder to the TCON RGB setup functions allows accessing the
connector from the encoder directly instead of relying on the panel.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-2-contact@paulk.fr
Until we have sorted out all problems.
v2: return -EINVAL during create if flag is set.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/260937/
Convert drm_atomic_plane_check() over to using explicit old vs. new
plane states. Avoids the confusion of "what does plane->state mean
again?".
v2: Stick to the multi-stage logic in plane_switching_crtc() (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106191624.2207-1-ville.syrjala@linux.intel.com
Replace 'crtc->state' with the explicit old crtc state.
Actually it shouldn't matter whether we use the old or the new
crtc state here since any plane that has been removed from the
crtc since the crtc state was duplicated will have been added
to the atomic state already. That is, you can't call
drm_atomic_set_crtc_for_plane() without having the new
plane state already in hand.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101184646.14753-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Add a function to check whether there is at least one plane that
supports a specific format and modifier combination. Drivers can
use this to reject unsupported formats/modifiers in .fb_create().
v2: Accept anyformat if the driver doesn't do planes (Eric)
s/planes_have_format/any_plane_has_format/ (Eric)
Check the modifier as well since we already have a function
that does both
v3: Don't do the check in the core since we may not know the
modifier yet, instead export the function and let drivers
call it themselves
Cc: Eric Anholt <eric@anholt.net>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029183453.28541-1-ville.syrjala@linux.intel.com
It's lockless, and userspace might chance it underneath us. That's not
really a problem, all userspace gets is a slightly dysfunctional
lease with the current code. But this might change, and gcc might
decide to reload a few too many times, and then boom. So better safe
than sorry.
v2: Remove the now unused lessor_priv argument from validate_lease()
(Keith).
v3: Actually add everything ... silly me.
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@gmail.com>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181105101211.22737-1-daniel.vetter@ffwll.ch
This essentially undoes
commit 39868bd766
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Oct 29 08:55:58 2013 +0000
drm: Compact booleans within struct drm_file
We do lockless access to these flags everywhere, and it's kinda not a
great idea to mix lockless and bitfields. Aside from that gcc isn't
generating great code for these.
If this ever becomes an issue size-wise, I think we need atomic_t here
and atomic bitflag ops.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102132543.16486-2-daniel.vetter@ffwll.ch
I spent a bit of time scratching heads and figuring out why the igts
don't work. Probably useful to keep this work.
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@gmail.com>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102132543.16486-1-daniel.vetter@ffwll.ch
This broke rendering on V3D, where we almost always have a 0
in-syncobj.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 48197bc564 ("drm: add syncobj timeline support v9")
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.kernel.org/patch/10669317/
Signed-off-by: Christian König <christian.koenig@amd.com>
VGEM doesn't do anything modeset specific, so in a way exposing a
primary node is 'wrong'. At the same time, we extensively use if for
creating dumb buffers, fences, prime fd <> handle imports/exports.
To the point that we explicitly annotate the vgem fence ioctls as
DRM_RENDER_ALLOW and have an IGT test which opens the render node.
close(drm_open_driver_render(DRIVER_VGEM))
Better late than never, let's flip the switch.
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026120647.7528-1-emil.l.velikov@gmail.com
Allwinner H6 SoC has a cut down version of TCON TOP.
Add binding documentation for it.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[expanded description]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-26-jernej.skrabec@siol.net
Some SoCs, such as H6, doesn't have a full-featured TCON TOP.
Add quirks support for TCON TOP.
Currently the presence of TCON_TV1 and DSI is controlled via the quirks
structure.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Fixed code style and removed unnecessary initialization]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-25-jernej.skrabec@siol.net
It turns out that TCON TOP registers in H6 SoC have non-zero reset
value. This may cause issues if bits are not changed during
configuration.
To prevent that, initialize registers to 0.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-24-jernej.skrabec@siol.net
H6 has Synopsys DWC HDMI 2.0 TX PHY.
There is no freely available documentation for it, only code found in
BSP kernel. However, judging by the code, PHY is very similar to older
Synopsys HDMI PHY described in i.MX6 documentation. Most registers seem
to be the same.
According to i.MX6 documentation, mpll settings are based on pixel clock
and are not specific to each SoC. Because of that, mpll table in this
commit is based on that documentation and not on BSP code. Other PHY
settings were derived from BSP PHY driver code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-23-jernej.skrabec@siol.net
Currently sun8i-hdmi-phy driver supports only custom PHYs connected to
DW HDMI controller. Since newest Allwinner SoCs have unmodified Synopsys
PHY, driver has to be reorganized to support them.
Variant structure is expanded to allow differentiation between custom
and Sysnopsys PHYs and to hold Synopsys PHY settings.
Since DW HDMI bridge platform data has different fields for custom and
Sysnopsys PHY, function sun8i_hdmi_phy_get_ops() is replaced with
sun8i_hdmi_phy_set_ops().
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-22-jernej.skrabec@siol.net
Currently, quirks and compatibles are sorted alphabetically. However,
they should be sorted by family release date and then alphabetically.
Fix that by moving A64 quirks and compatible to bottom. No functional
change is made.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-21-jernej.skrabec@siol.net
The Allwinner H6 SoC uses a v2.12a DesignWare HDMI controller, with
dedicated CEC and HDCP clocks added; the PHY connected is a standard
DesignWare HDMI PHY.
Add binding for it.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[added HDCP clock and reset]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-19-jernej.skrabec@siol.net
It turns out that H6 HDMI BSP kernel driver doesn't change TMDS rate at
all. At this point it is not clear whether it is just not necessary or
it would cause some kind of issues.
Add a quirk for it.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-18-jernej.skrabec@siol.net
Since it is not possible to access sun8i-dw-hdmi driver private data
inside mode_valid function, make it configurable. That way different
versions of HDMI controllers can set different function, depending on
it's limitations.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-17-jernej.skrabec@siol.net
Currently supported Allwinner SoCs with DW HDMI controller have
scrambled addresses and read lock. However, that is not true in general.
For example, A80 and H6 have normal addresses and normal read access.
Move code for unscrambling addresses and unlocking read access to it's
own function and call it from init function.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-16-jernej.skrabec@siol.net
It turns out that even new DW HDMI controllers exhibits same magenta
line issues as older versions.
Enable workaround for v2.12a.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-15-jernej.skrabec@siol.net
Mixer 0 has 1 VI and 3 UI planes, scaler on all planes and can output
4K image @60Hz. It also support 10 bit colors, which are not yet
implemented.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-14-jernej.skrabec@siol.net
Display Engine 3 is an upgrade of DE2 with new features like support for
10 bit color formats and support for AFBC.
Most of DE2 code works with DE3, except some small details.
Implement basic support for DE3. Support for 10 bit colort formats and
AFBC, among others missing features, will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/260238/
Most, if not all, registers found in DE2 still exists in DE3. However,
units are on different base addresses.
To prepare for addition of DE3 support, registers macros are reworked so
they take base address as parameter.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[rebased]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-10-jernej.skrabec@siol.net
This commit adds compatibles used in H6 display pipeline, namely for
display engine, mixer and TV TCON.
H6 display engine is somewhat similar to R40, just less TCONs and
mixer support more features.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-8-jernej.skrabec@siol.net
The Allwinner H6 DE3 bus is similar to the A64 DE2 one.
Add its compatible string with the A64 string as fallback to the
binding.
Some description of the binding is modified to make it more generic.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Fixed compatible name]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-2-jernej.skrabec@siol.net
Leases are entirely implemented within drm.ko, no need to even tempt
drivers into doing nasty things. And if there's really a need, we can
always re-export these again.
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@gmail.com>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102143107.25722-1-daniel.vetter@ffwll.ch
Add tests that verify that drm_internal_framebuffer_create creates
buffers correctly by creating a dummy drm_device with a mock function
for the fb_create callback.
To decide if a buffer has been created or not it just checks if
fb_create callback has been called for the particular drm_mode_fb_cmd2
that's being tested.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101151051.1509-8-alexandru-cosmin.gheorghe@arm.com
If we want to be able to write drmselftests for non-static core
functions that are not intended to be used by drivers we need this
functions to be exported.
This adds a macro that is tied of CONFIG_DRM_DEBUG_SELFTEST, and uses
that to export drm_internal_framebuffer_create, in order for
subsequent patches to be able to test it.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101151051.1509-7-alexandru-cosmin.gheorghe@arm.com
Mali-DP implements a number of tiled yuv formats which are not
currently described in drm_fourcc.h.
This adds those definitions and describes their memory layout by
using the newly added char_per_block, block_w, block_h.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101151051.1509-3-alexandru-cosmin.gheorghe@arm.com
For some pixel formats .cpp structure in drm_format info it's not
enough to describe the peculiarities of the pixel layout, for example
tiled formats or packed formats at bit level.
What's implemented here is to add three new members to drm_format_info
that could describe such formats:
- char_per_block[3]
- block_w[3]
- block_h[3]
char_per_block will be put in a union alongside cpp, for transparent
compatibility with the existing format descriptions.
Regarding, block_w and block_h they are intended to be used through
their equivalent getters drm_format_info_block_width /
drm_format_info_block_height, the reason of the getters is to abstract
the fact that for normal formats block_w and block_h will be unset/0,
but the methods will be returning 1.
Additionally, convenience function drm_format_info_min_pitch had been
added that computes the minimum required pitch for a given pixel
format and buffer width.
Using that the following drm core functions had been updated to
generically handle both block and non-block formats:
- drm_fb_cma_get_gem_addr: for block formats it will just return the
beginning of the block.
- framebuffer_check: Use the newly added drm_format_info_min_pitch.
- drm_gem_fb_create_with_funcs: Use the newly added
drm_format_info_min_pitch.
- In places where is not expecting to handle block formats, like fbdev
helpers I just added some warnings in case the block width/height
are greater than 1.
Changes since v3:
- Add helper function for computing the minimum required pitch.
- Improve/cleanup documentation
Changes since v8:
- Fixed build on 32bits arm architectures, with:
- return DIV_ROUND_UP((u64)buffer_width * info->char_per_block[plane],
+ return DIV_ROUND_UP_ULL((u64)buffer_width * info->char_per_block[plane],
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101170055.5433-1-alexandru-cosmin.gheorghe@arm.com
Having failed any attempts at a more generic solution,
I fall back to the very specific solution: define a simple
panel for the ARM RTSM emulated platforms.
I am doing this so we can convert all old users from the
previous fbdev driver to the PL111 DRM driver.
This works fine as far as I can test, provided the
device tree for RTSM AEMv8 is augmented accordingly.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026111334.3365-1-linus.walleij@linaro.org
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jyri Sarha <jsarha@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025201340.34227-9-noralf@tronnes.org
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025201340.34227-8-noralf@tronnes.org
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025201340.34227-7-noralf@tronnes.org
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025201340.34227-3-noralf@tronnes.org
