It's not a very good idea to allocate memory during EH. Use
statically allocated buffer for dev->id[] and add 512byte buffer
ap->sector_buf. This buffer is owned by EH (or probing) and to be
used as temporary buffer for various purposes (IDENTIFY, NCQ log page
10h, PM GSCR block).
Signed-off-by: Tejun Heo <htejun@gmail.com>
ap->active_tag was cleared in ata_qc_free(). This left ap->active_tag
dangling after ata_qc_complete(). Spurious interrupts inbetween could
incorrectly access the qc. Clear active_tag in ata_qc_complete().
This change is necessary for later EH changes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_bus_probe() doesn't clear dev->class after ->phy_reset(). This
can result in falsely enabled devices if probing fails. Clear
dev->class to ATA_DEV_UNKNOWN after fetching it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
While moving ata_scsi_error() from LLDD sht to libata transportt,
EXPORT_SYMBOL_GPL() entry was left out. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Rename ata_down_sata_spd_limit() and friends to sata_down_spd_limit()
and likewise for simplicity & consistency.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Move ata_set_mode() failure handling outside of ap->ops->set_mode if
clause such that it can handle ap->ops->set_mode failures after it's
updated.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Devices which consumed all their changes used to be disabled every
iteration. This causes unnecessary noise in the console output.
Disable once and leave alone.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As waiting for some register bits to change seems to be a common
operation shared by some controllers, implement helper function
ata_wait_register(). This function also takes care of register write
flushing.
Note that the condition is inverted, the wait is over when the masked
value does NOT match @val. As we're waiting for bits to change, this
test is more powerful and allows the function to be used in more
places.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
@verbose was added to ata_reset_fn_t because AHCI complained during
probing if no device was attached to the port. However, muting
failure message isn't the correct approach. Reset methods are
responsible for detecting no device condition and finishing
successfully. Now that AHCI softreset is fixed, kill @verbose.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make setting CBL type responsibility of probeinit. This allows using
only ap->cbl == ATA_CBL_SATA test in all other parts. Without this,
ata_down_sata_spd_limit() doesn't work during probe reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Overriding the whole EH code is a per-transport, not per-host thing.
Move ->eh_strategy_handler to the transport class, same as
->eh_timed_out.
Downside is that scsi_host_alloc can't check for the total lack of EH
anymore, but the transition period from old EH where we needed it is
long gone already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert the ATAPI_ENABLE_DMADIR compile time option needed
by some SATA-PATA bridge to runtime module parameter.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
irq-pio minor fix:
- remove the redundant hsm_task_state = HSM_ST_IDLE
- add devno to printk() as done in upstream
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make libata-core routines which will be used by EH implementation
extern.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A lot of EH codes are about to be added to libata. Separate out
libata-eh.c. ata_scsi_timed_out(), ata_scsi_error(),
ata_qc_timeout(), ata_eng_timeout(), ata_eh_qc_complete() and
ata_eh_qc_retry() are moved. No code is changed by this patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current code passes pointer to ap around and repeatedly performs
ata_qc_from_tag() to access the ongoing qc. This is unnatural and
makes EH synchronization cumbersome. Make PIO codes deal with qc
instead of ap.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_dev_set_mode() is now responsible for managing ATA_DFLAG_PIO.
Clear it before setting it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_dev_configure() should not clear dynamic device flags determined
elsewhere. Lower eight bits are reserved for feature flags, define
ATA_DFLAG_CFG_MASK and clear only those bits before configuring
device. Without this patch, ATA_DFLAG_PIO gets turned off during
revalidation making PIO mode unuseable.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rename ATA_FLAG_PORT_DISABLED to ATA_FLAG_DISABLED for consistency.
(ATA_FLAG_* are always about ports).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure ata_dev_revalidate() complains on failures and kill
revalidation failure message printed from ata_dev_set_mode().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_bus_probe() now marks failed devices properly and leaves
meaningful transfer mode masks. This patch makes ata_dev_xfermask()
consider disable devices when determining PIO mode to avoid violating
device selection timing.
While at it, move port-wide resttriction out of device iteration loop
and try to make the function look a bit prettier.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve ata_bus_probe() such that configuration failures are handled
better. Each device is given ATA_PROBE_MAX_TRIES chances, but any
non-transient error (revalidation failure with -ENODEV, configuration
failure with -EINVAL...) disables the device directly. Any IO error
results in SATA PHY speed down and ata_set_mode() failure lowers
transfer mode. The last try always puts a device into PIO-0.
After each failure, the whole port is reset to make sure that the
controller and all the devices are in a known and stable state. The
reset also applies SATA SPD configuration if necessary.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ata_down_xfermask_limit(). This function manipulates
@dev->pio/mwdma/udma_mask such that the next lower transfer mode is
selected. This will be used to improve ata_bus_probe() failure
handling and later by EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some devices react badly if resets are performed back-to-back. Give
devices some time to breath and tell user that we're taking a nap.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_drive_probe_reset() use SATA SPD configuration. Hardreset
will be force if speed renegotiation is necessary. Also, if a
hardreset fails, PHY speed is stepped down and hardreset is retried
until the lowest speed is reached.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ap->sata_spd_limit contrains SATA PHY speed of the port. It is
initialized to the configured value prior to probing thus preserving
BIOS configured value. hardreset is responsible for applying SPD
limit and sata_std_hardreset() is updated to do that. SATA SPD limit
will be used to enhance failure handling during probing and later by
EH.
This patch also normalizes some comments around affected code.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't overwrite SPD setting during hard reset. This change has the
(intended) side effect of honoring the BIOS configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When ata_set_mode() fails on a device, make ata_set_mode() return
error code and pointer to the device instead of disabling it directly.
This gives more control to higher level driving logic.
This patch does not change the end result (configured transfer mode)
although it may make libata repeat mode configuration to the peer of a
failing device. Later ata_bus_probe() rewrite will make full use of
this change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Handle DRQ=1 ERR=1 situation. Revised according to what IDE try_to_flush_leftover_data() does.
Changes:
- For ATA PIO writes and ATAPI devices, just stop the HSM and let EH handle it.
- For ATA PIO reads, read only one block of junk data and then let EH handle it.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Merge ata_host_set_pio() and ata_host_set_dma() into ata_set_mode()
and use function-level *dev to iterate over devices. This eases
soon-to-follow ata_set_mode() interface change.
While at it, kill an unnecessary comment and normalize others.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_set_mode() return without doing anything if there is no
device on the port. This is in preparation for ata_bus_probe()
changes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch renames ata_dev_present() to ata_dev_enabled() and adds
ata_dev_disabled(). This is to discern the state where a device is
present but disabled from not-present state. This disctinction is
necessary when configuring transfer mode because device selection
timing must not be violated even if a device fails to configure.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make do_probe_reset() generic by pushing classification check into
ata_drive_probe_reset() and rename it to ata_do_reset(). This will be
used by EH reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ata_spd_string() from sata_print_link_status(). This
will be used by SATA spd configuration routines.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_bus_probe() uses unsigned int rc to receive negative errno and
returns the converted unsigned int value. Convert temporary variables
to int and make ata_bus_probe() return negative errno on failure.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_set_mode() return correct error value when ata_dev_set_mode()
fails.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_xfer_tbl is terminated by entry with -1 as ->shift. However,
->shift was unsigned int making the termination condition bogus. This
patch converts ->shift and ->bits to int.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is no reason for the issuer to diddle with a failed qc as the
issuer has complete control over when a qc gets freed (usually in
->complete_fn). Make ata_qc_issue() responsible for completing qcs
which failed to issue.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On sg_err failure path, ata_qc_issue() doesn't mark the qc active
before returning. This triggers WARN_ON() in __ata_qc_complete() when
the qc gets completed. This patch moves ap->active_tag and
QCFLAG_ACTIVE setting to the top of the function.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
print out information for ATAPI devices with CDB interrupts
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_dev_init_params() fixes:
- Get the "heads" and "sectors" parameters from caller instead of implicitly from dev->id[].
- Return AC_ERR_INVALID instead of 0 if an invalid parameter is found
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Last of the set, just clean up some oddments. Assuming the whole set is
now ok then the remaining differences are the setup of PIO_0 at reset
and the ->data_xfer method.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a field to the host_set called 'flags' (was host_set_flags changed
to suit Jeff)
Add a simplex_claimed field so we can remember who owns the DMA channel
Add a ->mode_filter() hook to allow drivers to filter modes
Add docs for mode_filter and set_mode
Filter according to simplex state
Filter cable in core
This provides the needed framework to support all the mode rules found
in the PATA world. The simplex filter deals with 'to spec' simplex DMA
systems found in older chips. The cable filter avoids duplicating the
same rules in each chip driver with PATA. Finally the mode filter is
neccessary because drive/chip combinations have errata that forbid
certain modes with some drives or types of ATA object.
Drive speed setup remains per channel for now and the filters now use
the framework Tejun put into place which cleans them up a lot from the
older libata-pata patches.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I think this is still needed with the new probe code (which btw seems to
be missing docs in upstream ?).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some hardware doesn't want the usual mode setup logic running. This
allows the hardware driver to replace it for special cases in the least
invasive way possible.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some CD-ROM drives are slow to clear DRQ, after the last data block
is read by PIO. Use ata_wait_idle() after reading the last data block.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Current irq-pio checks ERR bit and stops on ERR before it does anything else.
This behavior doesn't look right.
The DRQ bit should take higher precedence than the ERR bit.
Changes:
- Let the HSM do the data transfer whenever the
device asks for DRQ bit, even if the ERR bit is set.
- For DRQ=1 ERR=1, don't trust the data
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the the in_wq check easier to read as an inline function.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_check_atapi_dma() fix for LLDDs with the ATA_FLAG_PIO_POLLING flag.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup the following unused functions:
- ata_pio_poll()
- ata_pio_complete()
- ata_pio_first_block()
- ata_pio_block()
- ata_pio_error()
ap->pio_task_timeout and other enums.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert ata_pio_task() to use the new ata_hsm_move().
Changes:
- refactor ata_pio_task() to poll device status register and
- call the new ata_hsm_move() when device indicates it is not BSY.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Let ata_hsm_move() work with both irq-pio and polling pio codepath.
Changes:
- add a new parameter "in_wq" for polling pio
- add return value "poll_next" to tell polling pio task whether the HSM is finished
- merge code from ata_pio_first_block() to the HSM_ST_FIRST state.
- call ata_poll_qc_complete() if called from the workqueue
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Minor fix for ata_hsm_move() to work with ata_host_intr().
Changes:
- WARN_ON() and comment fix
- Make the HSM_ST_LAST device status checking more rigid.
- Treat unknown HSM state as BUG().
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move out the irq-pio HSM code from ata_host_intr() to the new ata_hsm_move() function verbatim.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
atapi_packet_task() was replaced by ata_pio_task().
Remove the unused atapi_packet_task().
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix merge problem with upstream.
Changes:
1. add missing dev->cdb_len = 16 for ATA devices
2. use ata_pio_task instead of atapi_packet_task
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add FIXME above ata_dev_xfermask noting that the current
implementation limits all transfer modes to the fastest of the slowest
device on a port which isn't necessary.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_bus_softreset() should return AC_ERR_* on failure not arbitrary
positive number. While at it, reformat comment above it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
E.D.D. has no user in-tree and mostly useless. Kill it. For possible
out-of-tree users, add a nice warning message and error handling if
LLDD doesn't report any useable reset mechanism (and thus tries to use
E.D.D.).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove some of the dependence on the host_set struct
in preparation for supporting SAS HBAs. Adds a struct device
pointer to the ata_port struct.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At the moment libata doesn't pass pm_message_t down ata_device_suspend.
This causes drives to be powered down when we just want a freeze,
causing unnecessary wear and tear. This patch gets pm_message_t passed
down so that it can be used to determine whether to power down the
drive.
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
drivers/scsi/libata-core.c | 5 +++--
drivers/scsi/libata-scsi.c | 4 ++--
drivers/scsi/scsi_sysfs.c | 2 +-
include/linux/libata.h | 4 ++--
include/scsi/scsi_host.h | 2 +-
5 files changed, 9 insertions(+), 8 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_set_mode() responsible for determining whether to take port
or device offline on failure. ata_dev_set_xfermode() and
ata_dev_set_mode() indicate error to the caller instead of disabling
port directly on failure. Also, for consistency, ata_dev_present()
check is done in ata_set_mode() instead of ata_dev_set_mode().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We may or may not disable a device after ata_dev_configure() fails.
Kill 'not supported, ignoring' message in ata_dev_configure() and use
ata_dev_disable() in ata_bus_probe().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch implements ata_dev_disable() which prints a warning message
and takes @dev offline. Currently, this is done by explicitly
incrementing dev->class with case-by-case warning messages. Giving
user clear indication when libata gives up will be more important as
libata will be doing more retries.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata core is being changed to disallow port/device disable on lower
layers. However, some LLDDs (sata_mv) directly disable port on
command failure. This patch makes ata_exec_internal() check whether a
port got disabled after an internal command. If it is, AC_ERR_SYSTEM
is added to err_mask and the port gets re-enabled.
As internal command failure results in device disable for drivers
which don't implement newer reset/EH callbacks, this change results in
no behavior change for single device per port controllers. For
slave-possible LLDDs which disable port on command failure, (1) such
drivers don't exist currently, (2) issuing command to the other device
of once-disabled port shouldn't result in catastrophe even if such
driver exists. So, this should be enough as a temporary measure.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that each ata_device has xfer masks, per-dev limits can be made
per-dev instead of per-port. Make per-dev limits per-dev.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add per-dev pio/mwdma/udma_mask. All transfer mode limits used to be
applied to ap->*_mask which unnecessarily restricted other devices
sharing the port. This change will also benefit later EH speed down
and hotplug.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Not much to say here except that some drives have fixed and bad firmware
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current code follows the spec but uses an overlong delay. This would
be great if the hardware did. Several vendors however forget the D7
pulldown. Fortunately 0xFF isnt a sane reset state so we can use it to
skip detection as is done in drivers/ide. (ie this is a tested solution
over a long time)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan noted: "bmdma may be zero but the bmdma_irq_clear function gets
called even in this case during pure PIO operation. Check we have a
bmdma before we use it."
I fixed this by adding a check for zero. While was I there, I fixed the
non-standard indentation of the small function's code.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
