Currently, ondemand calculates the target frequency proportional to load
using the formula:
Target frequency = C * load
where C = policy->cpuinfo.max_freq / 100
Though, in many cases, the minimum available frequency is pretty high and
the above calculation introduces a dead band from load 0 to
100 * policy->cpuinfo.min_freq / policy->cpuinfo.max_freq where the target
frequency is always calculated to less than policy->cpuinfo.min_freq and
the minimum frequency is selected.
For example: on Intel i7-3770 @ 3.4GHz the policy->cpuinfo.min_freq = 1600000
and the policy->cpuinfo.max_freq = 3400000 (without turbo). Thus, the CPU
starts to scale up at a load above 47.
On quad core 1500MHz Krait the policy->cpuinfo.min_freq = 384000
and the policy->cpuinfo.max_freq = 1512000. Thus, the CPU starts to scale
at load above 25.
Change the calculation of target frequency to eliminate the above effect using
the formula:
Target frequency = A + B * load
where A = policy->cpuinfo.min_freq and
B = (policy->cpuinfo.max_freq - policy->cpuinfo->min_freq) / 100
This will map load values 0 to 100 linearly to cpuinfo.min_freq to
cpuinfo.max_freq.
Also, use the CPUFREQ_RELATION_C in __cpufreq_driver_target to select the
closest frequency in frequency_table. This is necessary to avoid selection
of minimum frequency only when load equals to 0. It will also help for selection
of frequencies using a more 'fair' criterion.
Tables below show the difference in selected frequency for specific values
of load without and with this patch. On Intel i7-3770 @ 3.40GHz:
Without With
Load Target Selected Target Selected
0 0 1600000 1600000 1600000
5 170050 1600000 1690050 1700000
10 340100 1600000 1780100 1700000
15 510150 1600000 1870150 1900000
20 680200 1600000 1960200 2000000
25 850250 1600000 2050250 2100000
30 1020300 1600000 2140300 2100000
35 1190350 1600000 2230350 2200000
40 1360400 1600000 2320400 2400000
45 1530450 1600000 2410450 2400000
50 1700500 1900000 2500500 2500000
55 1870550 1900000 2590550 2600000
60 2040600 2100000 2680600 2600000
65 2210650 2400000 2770650 2800000
70 2380700 2400000 2860700 2800000
75 2550750 2600000 2950750 3000000
80 2720800 2800000 3040800 3000000
85 2890850 2900000 3130850 3100000
90 3060900 3100000 3220900 3300000
95 3230950 3300000 3310950 3300000
100 3401000 3401000 3401000 3401000
On ARM quad core 1500MHz Krait:
Without With
Load Target Selected Target Selected
0 0 384000 384000 384000
5 75600 384000 440400 486000
10 151200 384000 496800 486000
15 226800 384000 553200 594000
20 302400 384000 609600 594000
25 378000 384000 666000 702000
30 453600 486000 722400 702000
35 529200 594000 778800 810000
40 604800 702000 835200 810000
45 680400 702000 891600 918000
50 756000 810000 948000 918000
55 831600 918000 1004400 1026000
60 907200 918000 1060800 1026000
65 982800 1026000 1117200 1134000
70 1058400 1134000 1173600 1134000
75 1134000 1134000 1230000 1242000
80 1209600 1242000 1286400 1242000
85 1285200 1350000 1342800 1350000
90 1360800 1458000 1399200 1350000
95 1436400 1458000 1455600 1458000
100 1512000 1512000 1512000 1512000
Tested on Intel i7-3770 CPU @ 3.40GHz and on ARM quad core 1500MHz Krait
(Android smartphone).
Benchmarks on Intel i7 shows a performance improvement on low and medium
work loads with lower power consumption. Specifics:
Phoronix Linux Kernel Compilation 3.1:
Time: -0.40%, energy: -0.07%
Phoronix Apache:
Time: -4.98%, energy: -2.35%
Phoronix FFMPEG:
Time: -6.29%, energy: -4.02%
Also, running mp3 decoding (very low load) shows no differences with and
without this patch.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit dfa5bb6225 (cpufreq: ondemand: Change the calculation
of target frequency), this return statement is no longer needed.
Reported-by: Henrik Nilsson <Karl.Henrik.Nilsson@gmail.com>
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Function __cpufreq_driver_target() checks if target_freq is within
policy->min and policy->max range. generic_powersave_bias_target() also
checks if target_freq is valid via a cpufreq_frequency_table_target()
call. So, drop the unnecessary duplicate check in *_check_cpu().
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Chapter 14 of Documentation/CodingStyle says:
The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts
readability and introduces an opportunity for a bug when the pointer
variable type is changed but the corresponding sizeof that is passed
to a memory allocator is not.
This wasn't followed consistently in drivers/cpufreq, let's make it
more consistent by always following this rule.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
They are called policy, cur_policy, new_policy, data, etc. Just call
them policy wherever possible.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch addresses the following issues in the header files in the
cpufreq core:
- Include headers in ascending order, so that we don't add same
many times by mistake.
- <asm/> must be included after <linux/>, so that they override
whatever they need to.
- Remove unnecessary includes.
- Don't include files already included by cpufreq.h or
cpufreq_governor.h.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This sysfs file was called ignore_nice_load earlier and commit
4d5dcc4 (cpufreq: governor: Implement per policy instances of
governors) changed its name to ignore_nice by mistake.
Lets get it renamed back to its original name.
Reported-by: Martin von Gagern <Martin.vGagern@gmx.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ondemand governor calculates load in terms of frequency and
increases it only if load_freq is greater than up_threshold
multiplied by the current or average frequency. This appears to
produce oscillations of frequency between min and max because,
for example, a relatively small load can easily saturate minimum
frequency and lead the CPU to the max. Then, it will decrease
back to the min due to small load_freq.
Change the calculation method of load and target frequency on the
basis of the following two observations:
- Load computation should not depend on the current or average
measured frequency. For example, absolute load of 80% at 100MHz
is not necessarily equivalent to 8% at 1000MHz in the next
sampling interval.
- It should be possible to increase the target frequency to any
value present in the frequency table proportional to the absolute
load, rather than to the max only, so that:
Target frequency = C * load
where we take C = policy->cpuinfo.max_freq / 100.
Tested on Intel i7-3770 CPU @ 3.40GHz and on Quad core 1500MHz Krait.
Phoronix benchmark of Linux Kernel Compilation 3.1 test shows an
increase ~1.5% in performance. cpufreq_stats (time_in_state) shows
that middle frequencies are used more, with this patch. Highest
and lowest frequencies were used less by ~9%.
[rjw: We have run multiple other tests on kernels with this
change applied and in the vast majority of cases it turns out
that the resulting performance improvement also leads to reduced
consumption of energy. The change is additionally justified by
the overall simplification of the code in question.]
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When initializing the default powersave_bias value, we need to first
make sure that this policy is running the ondemand governor.
Reported-and-tested-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I don't see how the virtual address of the tuners pointer would be of
any help to anyone so remove it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This allows for another [arch specific] driver to hook into existing
powersave bias function of the ondemand governor. i.e. This allows AMD
specific powersave bias function (in a separate AMD specific driver)
to aid ondemand governor's frequency transition decisions.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently we always calculate the CPU iowait time and add it to idle time.
If we are in ondemand and we use io_is_busy, we re-calculate iowait time
and we subtract it from idle time.
With this patch iowait time is calculated only when necessary avoiding
the double call to get_cpu_iowait_time_us. We use a parameter in
function get_cpu_idle_time to distinguish when the iowait time will be
added to idle time or not, without the need of keeping the prev_io_wait.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.,org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Following patch has introduced per cpu timers or works for ondemand and
conservative governors.
commit 2abfa876f1
Author: Rickard Andersson <rickard.andersson@stericsson.com>
Date: Thu Dec 27 14:55:38 2012 +0000
cpufreq: handle SW coordinated CPUs
This causes additional unnecessary interrupts on all cpus when the load is
recently evaluated by any other cpu. i.e. When load is recently evaluated by cpu
x, we don't really need any other cpu to evaluate this load again for the next
sampling_rate time.
Some sort of code is present to avoid that but we are still getting timer
interrupts for all cpus. A good way of avoiding this would be to modify delays
for all cpus (policy->cpus) whenever any cpu has evaluated load.
This patch does this change and some related code cleanup.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because we have per cpu timer now, we check if we need to evaluate load again or
not (In case it is recently evaluated). Here the 2nd cpu which got timer
interrupt updates core_dbs_info->sample_type irrespective of load evaluation is
required or not. Which is wrong as the first cpu is dependent on this variable
set to an older value.
Moreover it would be best in this case to schedule 2nd cpu's timer to
sampling_rate instead of freq_lo or hi as that must be managed by the other cpu.
In case the other cpu idles in between then also we wouldn't loose much power.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, there can't be multiple instances of single governor_type.
If we have a multi-package system, where we have multiple instances
of struct policy (per package), we can't have multiple instances of
same governor. i.e. We can't have multiple instances of ondemand
governor for multiple packages.
Governors directory in sysfs is created at /sys/devices/system/cpu/cpufreq/
governor-name/. Which again reflects that there can be only one
instance of a governor_type in the system.
This is a bottleneck for multicluster system, where we want different
packages to use same governor type, but with different tunables.
This patch uses the infrastructure provided by earlier patch and
implements init/exit routines for ondemand and conservative
governors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix some typos in comments.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order to avoid the calculation of up_threshold - down_differential
every time that the frequency must be decreased, we replace the
down_differential tuner with the adj_up_threshold which keeps the
difference across multiple checks.
Update the adj_up_threshold only when the up_theshold is also updated.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the inclusion of following patches:
9f4eb10 cpufreq: conservative: call dbs_check_cpu only when necessary
772b4b1 cpufreq: ondemand: call dbs_check_cpu only when necessary
code redundancy between the conservative and ondemand governors is
introduced again, so get rid of it.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix governors code to set all cpu's cdbs->cpu to the the actual cpu id
and use cur_policy->cpu istead of cdbs->cpu to track current governor's
leader cpu.
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Implement a generic helper function policy_is_shared() to replace the
current dbs_sw_coordinated_cpus() at cpufreq level, so that it can be
used by code other than cpufreq governors.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify update_sampling_rate() to check, and eventually immediately
schedule, all CPU's do_dbs_timer delayed work.
This is required in case of software coordinated CPUs, as we now have a
separate delayed work for each CPU.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify ondemand timer to not resample CPU utilization if recently
sampled from another SW coordinated core.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fixes a bug that occurred when we had load on a secondary CPU
and the primary CPU was sleeping. Only one sampling timer was spawned
and it was spawned as a deferred timer on the primary CPU, so when a
secondary CPU had a change in load this was not detected by the cpufreq
governor (both ondemand and conservative).
This patch make sure that deferred timers are run on all CPUs in the
case of software controlled CPUs that run on the same frequency.
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix cpufreq_gov_ondemand to skip CPU where another governor is used.
The bug present itself as NULL pointer access on the mutex_lock() call,
an can be reproduced on an SMP machine by setting the default governor
to anything other than ondemand, setting a single CPU's governor to
ondemand, then changing the sample rate by writing on:
> /sys/devices/system/cpu/cpufreq/ondemand/sampling_rate
Backtrace:
Nov 26 17:36:54 balto kernel: [ 839.585241] BUG: unable to handle kernel NULL pointer dereference at (null)
Nov 26 17:36:54 balto kernel: [ 839.585311] IP: [<ffffffff8174e082>] __mutex_lock_slowpath+0xb2/0x170
[snip]
Nov 26 17:36:54 balto kernel: [ 839.587005] Call Trace:
Nov 26 17:36:54 balto kernel: [ 839.587030] [<ffffffff8174da82>] mutex_lock+0x22/0x40
Nov 26 17:36:54 balto kernel: [ 839.587067] [<ffffffff81610b8f>] store_sampling_rate+0xbf/0x150
Nov 26 17:36:54 balto kernel: [ 839.587110] [<ffffffff81031e9c>] ? __do_page_fault+0x1cc/0x4c0
Nov 26 17:36:54 balto kernel: [ 839.587153] [<ffffffff813309bf>] kobj_attr_store+0xf/0x20
Nov 26 17:36:54 balto kernel: [ 839.587192] [<ffffffff811bb62d>] sysfs_write_file+0xcd/0x140
Nov 26 17:36:54 balto kernel: [ 839.587234] [<ffffffff8114c12c>] vfs_write+0xac/0x180
Nov 26 17:36:54 balto kernel: [ 839.587271] [<ffffffff8114c472>] sys_write+0x52/0xa0
Nov 26 17:36:54 balto kernel: [ 839.587306] [<ffffffff810321ce>] ? do_page_fault+0xe/0x10
Nov 26 17:36:54 balto kernel: [ 839.587345] [<ffffffff81751202>] system_call_fastpath+0x16/0x1b
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Restore the correct delay value for ondemand's od_dbs_timer, as it was
changed erroneously in commit 83f0e55 (cpufreq: governors: remove
redundant code).
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Initially ondemand governor was written and then using its code conservative
governor is written. It used a lot of code from ondemand governor, but copy of
code was created instead of using the same routines from both governors. Which
increased code redundancy, which is difficult to manage.
This patch is an attempt to move common part of both the governors to
cpufreq_governor.c file to come over above mentioned issues.
This shouldn't change anything from functionality point of view.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Multiple cpufreq governers have defined similar get_cpu_idle_time_***()
routines. These routines must be moved to some common place, so that all
governors can use them.
So moving them to cpufreq_governor.c, which seems to be a better place for
keeping these routines.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Improved system suspend/resume and runtime PM handling for the SH TMU, CMT
and MTU2 clock event devices (also used by ARM/shmobile).
* Generic PM domains framework extensions related to cpuidle support and
domain objects lookup using names.
* ARM/shmobile power management updates including improved support for the
SH7372's A4S power domain containing the CPU core.
* cpufreq changes related to AMD CPUs support from Matthew Garrett, Andre
Przywara and Borislav Petkov.
* cpu0 cpufreq driver from Shawn Guo.
* cpufreq governor fixes related to the relaxing of limit from Michal Pecio.
* OMAP cpufreq updates from Axel Lin and Richard Zhao.
* cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
* Runtime PM core updates related to the interactions with the system suspend
core from Alan Stern and Kevin Hilman.
* Wakeup sources modification allowing more helper functions to be called from
interrupt context from John Stultz and additional diagnostic code from Todd
Poynor.
* System suspend error code path fix from Feng Hong.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=rbCk
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael J Wysocki:
- Improved system suspend/resume and runtime PM handling for the SH
TMU, CMT and MTU2 clock event devices (also used by ARM/shmobile).
- Generic PM domains framework extensions related to cpuidle support
and domain objects lookup using names.
- ARM/shmobile power management updates including improved support for
the SH7372's A4S power domain containing the CPU core.
- cpufreq changes related to AMD CPUs support from Matthew Garrett,
Andre Przywara and Borislav Petkov.
- cpu0 cpufreq driver from Shawn Guo.
- cpufreq governor fixes related to the relaxing of limit from Michal
Pecio.
- OMAP cpufreq updates from Axel Lin and Richard Zhao.
- cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
- Runtime PM core updates related to the interactions with the system
suspend core from Alan Stern and Kevin Hilman.
- Wakeup sources modification allowing more helper functions to be
called from interrupt context from John Stultz and additional
diagnostic code from Todd Poynor.
- System suspend error code path fix from Feng Hong.
Fixed up conflicts in cpufreq/powernow-k8 that stemmed from the
workqueue fixes conflicting fairly badly with the removal of support for
hardware P-state chips. The changes were independent but somewhat
intertwined.
* tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
Revert "PM QoS: Use spinlock in the per-device PM QoS constraints code"
PM / Runtime: let rpm_resume() succeed if RPM_ACTIVE, even when disabled, v2
cpuidle: rename function name "__cpuidle_register_driver", v2
cpufreq: OMAP: Check IS_ERR() instead of NULL for omap_device_get_by_hwmod_name
cpuidle: remove some empty lines
PM: Prevent runtime suspend during system resume
PM QoS: Use spinlock in the per-device PM QoS constraints code
PM / Sleep: use resume event when call dpm_resume_early
cpuidle / ACPI : move cpuidle_device field out of the acpi_processor_power structure
ACPI / processor: remove pointless variable initialization
ACPI / processor: remove unused function parameter
cpufreq: OMAP: remove loops_per_jiffy recalculate for smp
sections: fix section conflicts in drivers/cpufreq
cpufreq: conservative: update frequency when limits are relaxed
cpufreq / ondemand: update frequency when limits are relaxed
properly __init-annotate pm_sysrq_init()
cpufreq: Add a generic cpufreq-cpu0 driver
PM / OPP: Initialize OPP table from device tree
ARM: add cpufreq transiton notifier to adjust loops_per_jiffy for smp
cpufreq: Remove support for hardware P-state chips from powernow-k8
...
Reevaluate CPU load and update frequency immediately whenever limits
are changed. Currently ondemand doesn't do that when limits are
relaxed, wasting power on systems with relatively low sampling rate.
Signed-off-by: Michal Pecio <mpecio@nvidia.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Initalizers for deferrable delayed_work are confused.
* __DEFERRED_WORK_INITIALIZER()
* DECLARE_DEFERRED_WORK()
* INIT_DELAYED_WORK_DEFERRABLE()
Rename them to
* __DEFERRABLE_WORK_INITIALIZER()
* DECLARE_DEFERRABLE_WORK()
* INIT_DEFERRABLE_WORK()
This patch doesn't cause any functional changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
When a new sampling rate is shorter than the current one, (e.g., 1 sec
--> 10 ms) regardless how short the new one is, the current ondemand
mechanism wait for the previously set timer to be expired.
For example, if the user has just expressed that the sampling rate
should be 10 ms from now and the previous was 1000 ms, the new rate may
become effective 999 ms later, which could be not acceptable for the
user if the user has intended to speed up sampling because the system is
expected to react to CPU load fluctuation quickly from __now__.
In order to address this issue, we need to cancel the previously set
timer (schedule_delayed_work) and reset the timer if resetting timer is
expected to trigger the delayed_work ealier.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq: (23 commits)
[CPUFREQ] EXYNOS: Removed useless headers and codes
[CPUFREQ] EXYNOS: Make EXYNOS common cpufreq driver
[CPUFREQ] powernow-k8: Update copyright, maintainer and documentation information
[CPUFREQ] powernow-k8: Fix indexing issue
[CPUFREQ] powernow-k8: Avoid Pstate MSR accesses on systems supporting CPB
[CPUFREQ] update lpj only if frequency has changed
[CPUFREQ] cpufreq:userspace: fix cpu_cur_freq updation
[CPUFREQ] Remove wall variable from cpufreq_gov_dbs_init()
[CPUFREQ] EXYNOS4210: cpufreq code is changed for stable working
[CPUFREQ] EXYNOS4210: Update frequency table for cpu divider
[CPUFREQ] EXYNOS4210: Remove code about bus on cpufreq
[CPUFREQ] s3c64xx: Use pr_fmt() for consistent log messages
cpufreq: OMAP: fixup for omap_device changes, include <linux/module.h>
cpufreq: OMAP: fix freq_table leak
cpufreq: OMAP: put clk if cpu_init failed
cpufreq: OMAP: only supports OPP library
cpufreq: OMAP: dont support !freq_table
cpufreq: OMAP: deny initialization if no mpudev
cpufreq: OMAP: move clk name decision to init
cpufreq: OMAP: notify even with bad boot frequency
...
Make cputime_t and cputime64_t nocast to enable sparse checking to
detect incorrect use of cputime. Drop the cputime macros for simple
scalar operations. The conversion macros are still needed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CPUFREQ Remove wall variable from cpufreq_gov_dbs_init()
Remove wall variable from cpufreq_gov_dbs_init() as
get_cpu_idle_time_us() no longer updates the last_update_time
unconditionally. Passing non-NULL last_update_time address
will result in accounting additional idle time with
update_ts_time_stats() before returning idle_sleeptime.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Dave Jones <davej@redhat.com>
--
drivers/cpufreq/cpufreq_ondemand.c | 3 +--
1 files changed, 1 insertions(+), 2 deletions(-)
This patch changes fields in cpustat from a structure, to an
u64 array. Math gets easier, and the code is more flexible.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Tuner <pjt@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1322498719-2255-2-git-send-email-glommer@parallels.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
time, s390: Get rid of compile warning
dw_apb_timer: constify clocksource name
time: Cleanup old CONFIG_GENERIC_TIME references that snuck in
time: Change jiffies_to_clock_t() argument type to unsigned long
alarmtimers: Fix error handling
clocksource: Make watchdog reset lockless
posix-cpu-timers: Cure SMP accounting oddities
s390: Use direct ktime path for s390 clockevent device
clockevents: Add direct ktime programming function
clockevents: Make minimum delay adjustments configurable
nohz: Remove "Switched to NOHz mode" debugging messages
proc: Consider NO_HZ when printing idle and iowait times
nohz: Make idle/iowait counter update conditional
nohz: Fix update_ts_time_stat idle accounting
cputime: Clean up cputime_to_usecs and usecs_to_cputime macros
alarmtimers: Rework RTC device selection using class interface
alarmtimers: Add try_to_cancel functionality
alarmtimers: Add more refined alarm state tracking
alarmtimers: Remove period from alarm structure
alarmtimers: Remove interval cap limit hack
...
update_ts_time_stat currently updates idle time even if we are in
iowait loop at the moment. The only real users of the idle counter
(via get_cpu_idle_time_us) are CPU governors and they expect to get
cumulative time for both idle and iowait times.
The value (idle_sleeptime) is also printed to userspace by print_cpu
but it prints both idle and iowait times so the idle part is misleading.
Let's clean this up and fix update_ts_time_stat to account both counters
properly and update consumers of idle to consider iowait time as well.
If we do this we might use get_cpu_{idle,iowait}_time_us from other
contexts as well and we will get expected values.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Cc: Dave Jones <davej@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Link: http://lkml.kernel.org/r/e9c909c221a8da402c4da07e4cd968c3218f8eb1.1314172057.git.mhocko@suse.cz
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There cannot be any concurrent access to these through
different cpu sysfs files anymore, because these tunables
are now all global (not per cpu).
I still have some doubts whether some of these locks
were needed at all. Anyway, let's get rid of them.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
CC: cpufreq@vger.kernel.org
Marked deprecated for quite a whilte now...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
CC: cpufreq@vger.kernel.org
Marked deprecated for quite a while now...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
CC: cpufreq@vger.kernel.org
calculate ondemand delay after dbs_check_cpu call because it can
modify rate_mult value
use freq_lo_jiffies value for the sub sample period of powersave_bias mode
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Dave Jones <davej@redhat.com>
With cmwq, there's no reason for cpufreq drivers to use separate
workqueues. Remove the dedicated workqueues from cpufreq_conservative
and cpufreq_ondemand and use system_wq instead. The work items are
already sync canceled on stop, so it's already guaranteed that no work
is running on module exit.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Dave Jones <davej@redhat.com>
Cc: cpufreq@vger.kernel.org
Adds a new global tunable, sampling_down_factor. Set to 1 it makes no
changes from existing behavior, but set to greater than 1 (e.g. 100)
it acts as a multiplier for the scheduling interval for reevaluating
load when the CPU is at its top speed due to high load. This improves
performance by reducing the overhead of load evaluation and helping
the CPU stay at its top speed when truly busy, rather than shifting
back and forth in speed. This tunable has no effect on behavior at
lower speeds/lower CPU loads.
This patch is against 2.6.36-rc6.
This patch should help solve kernel bug 19672 "ondemand is slow".
Signed-off-by: David Niemi <dniemi@verisign.com>
Acked-by: Venkatesh Pallipadi <venki@google.com>
CC: Daniel Hollocher <danielhollocher@gmail.com>
CC: <cpufreq-list@vger.kernel.org>
CC: <linux-kernel@vger.kernel.org>
Signed-off-by: Dave Jones <davej@redhat.com>
For UP systems this is not required, and results in a more consistent
sample interval.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jocelyn Falempe <jocelyn.falempe@motorola.com>
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Make simpler to read and call.
*** v3 - Always call when powersave_bias is enabled.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, hypervisor: add missing <linux/module.h>
Modify the VMware balloon driver for the new x86_hyper API
x86, hypervisor: Export the x86_hyper* symbols
x86: Clean up the hypervisor layer
x86, HyperV: fix up the license to mshyperv.c
x86: Detect running on a Microsoft HyperV system
x86, cpu: Make APERF/MPERF a normal table-driven flag
x86, k8: Fix build error when K8_NB is disabled
x86, cacheinfo: Disable index in all four subcaches
x86, cacheinfo: Make L3 cache info per node
x86, cacheinfo: Reorganize AMD L3 cache structure
x86, cacheinfo: Turn off L3 cache index disable feature in virtualized environments
x86, cacheinfo: Unify AMD L3 cache index disable checking
cpufreq: Unify sysfs attribute definition macros
powernow-k8: Fix frequency reporting
x86, cpufreq: Add APERF/MPERF support for AMD processors
x86: Unify APERF/MPERF support
powernow-k8: Add core performance boost support
x86, cpu: Add AMD core boosting feature flag to /proc/cpuinfo
Fix up trivial conflicts in arch/x86/kernel/cpu/intel_cacheinfo.c and
drivers/cpufreq/cpufreq_ondemand.c
Pavel Machek pointed out that not all CPUs have an efficient
idle at high frequency. Specifically, older Intel and various
AMD cpus would get a higher powerusage when copying files from
USB.
Mike Chan pointed out that the same is true for various ARM
chips as well.
Thomas Renninger suggested to make this a sysfs tunable with a
reasonable default.
This patch adds a sysfs tunable for the new behavior, and uses
a very simple function to determine a reasonable default,
depending on the CPU vendor/type.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: davej@redhat.com
LKML-Reference: <20100509082651.46914d04@infradead.org>
[ minor tidyup ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
