so we can use have list gpio as example (probe via DT)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Today we mix pdata and drivers data in the struct atmel_lcdfb_info
Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add platform device-id table in order to identify the controller and
determine its configuration.
The currently used configuration parameters are:
have_alt_pixclock
- SOC uses an alternate pixel-clock calculation formula (at91sam9g45
non-ES)
have_hozval
- SOC has a HOZVAL field in LCDFRMCFG which is used to determine the
linesize for STN displays (at91sam9261, at921sam9g10 and at32ap)
have_intensity_bit
- SOC uses IBGR:555 rather than BGR:565 16-bit pixel layout
(at91sam9261, at91sam9263 and at91sam9rl)
This allows us to remove all the remaining uses of cpu_is macros from
the driver.
Tested on at91sam9263 and at91sam9g45, compile-tested for other
AT91-SOCs, and untested for AVR32.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix regression introduced by commit 787f9fd232 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather than
BGR:565.
The above commit removes the RGB:555-wiring hack by
removing the no longer used ATMEL_LCDC_WIRING_RGB555 define.
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix regression introduced by commit 787f9fd232 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather
than BGR:565.
Use SOC-type to determine the pixel layout.
Tested on at91sam9263 and at91sam9g45.
Cc: <stable@vger.kernel.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch introduces lcdc->lcdcon_pol_negative which set CONTRAST_CTR
register to inverted polarity.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Changed because old the definition of unsigned long cannot be negative.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the RGB555 wiring for the atmel LCD.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Specify how much physically continuous, DMA capable memory will be
allocated at driver initialization time. This allow to create framebuffer
device with larger virtual resolution. Combine with y-panning this can be
used to implement double buffering acceleration method.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the following compile error caused by commit
d22579b837 ("atmel_lcdfb: FIFO underflow
management"):
In file included from arch/avr32/boards/atstk1000/atstk1004.c:21:
include/video/atmel_lcdc.h:40: error: field 'task' has incomplete type
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Manage atmel_lcdfb FIFO underflow
Resetting the LCD and DMA allows to fix screen shifting after a FIFO
underflow. It follows reset sequence from errata "LCD Screen Shifting
After a Reset".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds different wiring mode for the LCD screen.
The legacy atmel LCDC IP uses a non standard color mode, "BGR-555.1" instead
"RGB-565". The major part of graphic stacks for embedded systems uses only
"RGB-565". It is possible to swap LCD IOs instead of doing this bit swapping
by software (See application note AT91SAM9 LCD Controller
http://www.atmel.com/dyn/resources/prod_documents/doc6300.pdf)
This wire swapping is done on the at91sam9rl-ek board (board code
using this patch will come later).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Teach atmel_lcdfb driver how to suspend/resume.
Note that the backlight control should probably do more of the same stuff:
turning off display power (more than just the backlight) and stopping the
clocks (and dma to drive the no-longer-seen display). No point in wasting
power to generate images that can't be observed, after all...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the sam9 EK boards, the LCD backlight is hooked up to a PWM output from
the LCD controller. It's controlled by "contrast" registers though.
This patch lets boards declare that they have that kind of backlight
control. The driver can then export this control, letting screenblank and
other operations actually take effect ... reducing the typically
substantial power drain from the backlight.
Note that it's not fully cooked
- doesn't force backlight off during system suspend
- the "power" and "blank" events may not be done right
This should be easily added in the future.
[nicolas.ferre@atmel.com: remove unneeded inline and rename functions]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting a display timing parameter too high or too low may cause it to
wrap around and thus become completely wrong. Validate the timings in
atmel_lcdfb_check_var() and saturate to the highest or lowest possible
value if necessary.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds a framebuffer driver to ATMEL AT91SAM9x and AT32 aka AVR32 platforms.
Those chips share quite the same IP and this code is suitable for both
architectures.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
