In case we configured the adapter to be a wake up source from
Wake-on-LAN, but we never actually woke up using Wake-on-LAN, we will
leave the adapter in MagicPacket matching mode, which prevents any other
type of packets from reaching the RX engine. Fix this by calling
bcmgenet_power_up() with GENET_POWER_WOL_MAGIC to restore the adapter
configuration in bcmgenet_resume().
The second problem we had was an imbalanced clock disabling in
bcmgenet_wol_resume(), the Wake-on-LAN slow clock is only enabled in
bcmgenet_suspend() if we configured Wake-on-LAN, yet we unconditionally
disabled the clock in bcmgenet_wol_resume().
Fixes: 8c90db72f9 ("net: bcmgenet: suspend and resume from Wake-on-LAN")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we bring the interface down, phy_stop() will schedule the PHY state
machine to call our link adjustment callback. By the time we do so, we
may have clock gated off the GENET hardware block, and this will cause
bus errors to happen in bcmgenet_mii_setup():
Make sure that we only touch the UMAC_CMD register when there is an
actual link. This is safe to do for two reasons:
- updating the Ethernet MAC registers only make sense when a physical
link is present
- the PHY library state machine first set phydev->link = 0 before
invoking phydev->adjust_link in the PHY_HALTED case
Fixes: 240524089d ("net: bcmgenet: only update UMAC_CMD if something changed")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that we properly suspend and resume the PHY device when we
enter low power modes. We had two calls to bcmgenet_mii_reset() which
will issue a software-reset to the PHY without using the PHY library,
get rid of them since they are completely bogus and mess up with the PHY
library state. Make sure that we reset the PHY library cached values
(link, pause and duplex) to allow the link adjustment callback to be
invoked when needed.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_set_hw_params() will read the hardware version and compare it
with the one we are getting from Device Tree. Due to the clock being
enabled too late, bcmgenet_set_hw_params() will cause bus errors since
the GENET hardware block is still gated off by the time
bcmgenet_set_hw_params() is called, this will also make us fail the
version check since we will read the value 0 from the hardware.
Fix this by requesting the clock before the first piece of code that
needs to access hardware register.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the fixed phy setup make sure to not overwrite a valid value of
phy_dn (that is holding a reference to a phy-handle) and also acquire a
reference to the MAC node to consistently return with the phy_dn pointer
holding a reference.
Also add the corresponding of_node_put in the error path and the remove
function.
Fixes: 9abf0c2b71 ("net: bcmgenet: use the new fixed PHY helpers")
Fixes: aa09677cba ("net: bcmgenet: add MDIO routines")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were two places that used kzalloc() with a multiplied sizeof(),
replace these with kcalloc as recommended by checkpatch.pl.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl flagged two locations that did not comply to "CHECK:
braces {} should be used on all arms of this statement", fix them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl flagged two blank lines which are not needed, and one that
was missing, fix them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl flagged a lot of "CHECK: Alignment should match open
parenthesis" checks, fix all of them to make the driver neater. While
at it fix some obvious typos and re-arrange some of the lines to avoid
going over 80 columns.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a smaller GPLv2 header and remove all the boilerplate code as well
as the FSF mail address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets shorter than ETH_ZLEN were not padded with zeroes, hence leaking
potentially sensitive information. This bug has been present since the
driver got accepted in commit 1c1008c793
("net: bcmgenet: add main driver file").
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link adjustment callback can be called as frequently as desired
by the PHY library, as such, let's avoid doing a Read/Modify/Write
sequence if nothing changed, since these register accesses can be
expensive.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that Wake-on-LAN support mode is fully integrated into the driver,
allow an user to query and configure Wake-on-LAN in the driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bcmgenet_suspend() to prepare the hardware for being put into
Wake-on-LAN mode if the device can wakeup the system, and Wake-on-LAN is
enabled. Whether we resume from Wake-on-LAN or not, make sure that
bcmgenet_resume() disables the UniMAC MagicPacket matching mode and puts
the hardware in a state where it can receive all incoming packets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_wol_resume() will create an unbalanced clock state for the
wol_clk clock pointer since everywhere else in the code, we always call
clk_prepare_enable() and clk_disable_unprepare(). This function also
calls init_umac() which is neither correct nor necessary since
bcmgenet_resume() and bcmgenet_open() already does that.
Finally calling bcmgenet_wol_resume() in bcmgenet_open() is not correct,
since the interface would not have been able to put us in Wake-on-LAN
mode if it was not UP before.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle UMAC_IRQ_MPD_R interrupt bit in our workqueue to make sure that
we properly re-configure the GENET adapter from Wake-on-LAN.
bcmgenet_power_up() makes sure that we will not leave the UniMAC
hardware in MagicPacket matching mode, since that would prevent any
other packet from being received.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bcmgenet_power_{up,down} to handle the case where the adapter has
been suspend respectively resumed from Wake-on-LAN using MagicPackets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add all the required code to program the GENET hardware to enter
Wake-on-LAN mode and wake using MagicPackets with or without SecureOn
password.
This code is hooked to the build system, but is not yet referenced from
ethtool or the main bcmgenet driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempt to the request the Wake-on-LAN interrupt bit, and if successful,
advertise wakeup capability instead of doing this unconditionnally.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement suspend/resume callbacks in the GENET driver. This makes sure
that we de-initialize and re-initialize the hardware correctly before
entering suspend and when resuming.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a bunch of helper functions: bcmgenet_netif_start,
bcmgenet_netif_stop and bcmgenet_intr_disable to help reuse code that is
going to be necessary for suspend/resume.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor the code touching the UniMAC RX/TX enable bits since we are going
to re-use it for implementing suspend/resume.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking for wol_enabled in bcmgenet_close() is bogus, since no other
code places set priv->wol_enabled. Remove that as it will conflict with
the upcoming and functional Wake-on-LAN implementation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII_MODE_EN bit was defined to 0, while it is actually 6. It was not
much of a problem on older designs where this was a no-op, and the RGMII
data-path would always be enabled, but newer GENET controllers need to
explicitely enable their RGMII data-pad using this bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware will provide this information as soon as we will start
processing incoming packets, so there is no need to set the RX buffer
length during buffer allocation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use the PHY library which will determine the link state for us, make
sure we start with a carrier off until libphy has completed the link
training.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as register_netdev() is called, the network device notifiers are
running which means that other parts of the kernel, or user-space
programs can call the network device ndo_open() callback and use the
interface.
Disable the Ethernet device clock before we register the network device
such that we do not create the following situation:
CPU0 CPU1
register_netdev()
bcmgenet_open()
clk_prepare_enable()
clk_disable_unprepare()
and leave the hardware block gated off, while we think it should be
gated on.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_connect_fixed_link() is becoming obsolete, and also required
platform code to register the fixed PHYs at the specified addresses for
those to be usable. Get rid of it and use the new of_phy_is_fixed_link()
plus of_phy_register_fixed_link() helpers to transition over the new
scheme.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
version.h inclusion is not necessary as detected by versioncheck.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the UniMAC block is configured to forward the CRC as part of the
Ethernet frame (priv->crc_fwd_en, set by default), enabling the hardware
RX checksum block unveiled that the dma_rxchk_bit was never set in the
per-packet status bits (dma_flag in bcmgenet_desc_rx). This would make
the chksum_ok variable to be never set to 1, and the networking stack
would have to compute the packet checksums, which takes a substantial
amount of time.
In order for the RXCHK block to properly compute the packet checksum in
hardware, we also need to set the RBUF_SKIP_FCS bit accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of always invoking netdev_get_tx_queue() in bcmgenet_xmit() and
bcmgenet_tx_reclaim(), just get the corresponding netdev_queue pointer
once and for all and manipulate it throughout bcmgenet_xmit() and
bcmgenet_tx_reclaim().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_pick_tx already takes care of making sure that a given
skb->queue_mapping value will remain within the number of advertised
hardware queue number, there is no need to re-do this again in the
driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCMGENET driver was not TX timestamping the SKBs it queued for
transmission, do this in bcmgenet_xmit() right before kicking the
Transmit DMA engine.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock cookie in bcmgenet_priv is never used, get rid of it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bh_lock spinlock is unused, remove it from the private driver structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is commented since it is unused, left-over from the very first
time this driver was merged.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop all the checks on priv->phydev since we will refuse probing the
driver if we cannot attach to a PHY device. Drop all checks on
priv->phydev. This also fixes some smatch issues reported by Dan
Carpenter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Documentation/driver-model/devres.txt, devm_request_and_ioremap()
is deprecated, so use devm_ioremap_resource() instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new configuration symbol: CONFIG_BCMGENET which allows
us to build the Broadcom GENET driver and hook the driver files into the
build system.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for configuring the port multiplexer hardware
which resides in front of the GENET Ethernet MAC controller. This allows
us to support:
- internal PHYs (using drivers/net/phy/bcm7xxx.c)
- MoCA PHYs which are an entirely separate hardware block not covered
here
- external PHYs and switches
Note that MoCA and switches are currently supported using the emulated
"fixed PHY" driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the BCMGENET main driver file which supports the
following:
- GENET hardware from V1 to V4
- support for reading the UniMAC MIB counters statistics
- support for the 5 transmit queues
- support for RX/TX checksum offload and SG
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchs adds the bcmgenet.h header file which contains all the
hardware definitions for the GENETv1 to v4 hardware blocks as well as
the driver private structure and MIB counters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
