The Tegra124 SATA controller requires 4 clocks. Increase this constant
to be able to use them all.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Nothing too interesting - another ahci platform driver variant,
additional controller support, minor fixes and cleanups"
* 'for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: Add Device ID for HighPoint RocketRaid 642L
ata: ep93xx: use dmaengine_prep_slave_sg api instead of internal callback
ahci: add PCI ID for Marvell 88SE91A0 SATA Controller
sata_fsl: remove check for CONFIG_MPC8315_DS
ahci: add support for Hisilicon sata
libahci_platform: add host_flags parameter in ahci_platform_init_host()
ata: ahci: append new hflag AHCI_HFLAG_NO_FBS
ata: use CONFIG_PM_SLEEP instead of CONFIG_PM where applicable in host drivers
ata: ahci_mvebu: new driver for Marvell Armada 380 AHCI interfaces
Documentation: dt-bindings: reformat and order list of ahci-platform compatibles
libata-sff: remove dead code
ata: SATL compliance for Inquiry Product Revision
pata_octeon_cf: use devm_kzalloc() to allocate cf_port
Append AHCI_HFLAG_NO_FBS to force turning off FBS flag.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
On Intel Valleyview SoC, SATA device sleep is not reliable. When
DEVSLP is attempted on certain SSDs, port_devslp write would fail
and result in malfunction of AHCI controller. AHCI controller may
be not shown in PCI enumeration after reset. Complete power source
removal may be required to recover from this failure. So we blacklist
this device and override host device reported capabilities such that
device LPM will only attempt slumber but not DEVSLP.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The AHCI specification allows hardware to choose to revert to
single MSI mode when fewer messages are allocated than requested.
Yet, at least ICH10 chipset reverts to single MSI mode even when
enough messages are allocated in some cases (see below).
This update forces the driver to not rely on initialization of
multiple MSIs mode alone and always check if "MSI Revert to
Single Message" (MRSM) mode was enforced by the controller and
fallback to the single MSI mode in case it did.
That prevents a situation when the driver configured multiple
per-port IRQ handlers, but the controller sends all port's
interrupts to a single IRQ, which could easily screw up the
interrupt handling and lead to delays and possibly crashes.
The fix was tested on a 6-port controller that successfully
reverted to the single MSI mode:
00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA
AHCI Controller (prog-if 01 [AHCI 1.0])
Subsystem: Super Micro Computer Inc Device 10a7
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 101
I/O ports at f110 [size=8]
I/O ports at f100 [size=4]
I/O ports at f0f0 [size=8]
I/O ports at f0e0 [size=4]
I/O ports at f020 [size=32]
Memory at fbf00000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
Capabilities: [70] Power Management version 3
Capabilities: [a8] SATA HBA v1.0
Capabilities: [b0] PCI Advanced Features
Kernel driver in use: ahci
With 6 ports just 8 MSI vectors should be enough, but the adapter
enforces the MRSM mode when less than 16 vectors are written to
the Multiple Messages Enable PCI register. I instigated MRSM mode
by forcing @nvec to 8 in ahci_init_interrupts().
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: linux-ide@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
On OMAP platforms the device needs to be runtime resumed before it can
be accessed. The OMAP HWMOD framework takes care of enabling the
module and its resources based on the device's runtime PM state.
In this patch we runtime resume during .probe() and runtime suspend
after .remove().
We also update the runtime PM state during .resume().
CC: Balaji T K <balajitk@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some platforms have a PHY hooked up to the SATA controller. The PHY
needs to be initialized and powered up for SATA to work. We do that
using the PHY framework.
tj: Minor comment formatting updates.
CC: Balaji T K <balajitk@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo<tj@kernel.org>
The allwinner-sun4i AHCI controller needs 2 clocks to be enabled and the
imx AHCI controller needs 3 clocks to be enabled.
tj: Minor comment formatting updates.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Allwinner A10 and A20 ARM SoCs have an AHCI sata controller which needs a
special register to be poked before starting the DMA engine.
This register gets reset on an ahci_stop_engine call, so there is no other
place then ahci_start_engine where this poking can be done.
This commit allows drivers to override ahci_start_engine behavior for use by
the Allwinner AHCI driver (and potentially other drivers in the future).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In order to save power consumption as much as possible.
* Disable sata phy internal pll reference clock when sysetem enter
into suspend mode, enable it after resume.
* Setup module parameter used to enable imx ahci test power down
mode(PDDQ) or not, when there is no device detected on the port
* minor modifications:
- The format of the copyright is changed, because that the original
one can't pass fsl internal patch reivew without the character
'(c)'.
- Exports ahci_platform_ops and ahci_error_handler().
NOTE:
* The hot-plug can't be supported when PDDQ mode is ever enabled.
* module parameter usage how-to:
- default: enable PDDQ mode when no device detected.
- add "ahci-imx.hotplug=1" into kernel command line if your don't
want to enable PDDQ mode when no device detected on the port.
tj: Slightly updated description and comments.
Signed-off-by: Richard Zhu <r65037@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
libata/for-3.10-fixes never got submitted during v3.10 cycle. Merge
it into for-3.11 so that it can be routed together with other changes
scheduled for v3.11.
Three trivial conflicts in drivers/ata/sata_rcar.c. All are caused by
1b20f6a9ad ("sata_rcar: add 'base' local variable to some functions")
conflicting with logic updates in for-3.10-fixes. The offending
commit simply adds local variable @base on functions which
dereferences sata_rcar_priv->base multiple times. The resolutions are
trivial - applying s/priv->base/base/ in the conflicting logic
updates.
Signed-off-by: Tejun Heo <tj@kernel.org>
Highbank supports SGPIO by bit-banging out the SGPIO signals over
three GPIO pins defined in the DTB. Add support for this SGPIO
functionality.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently all interrupts assigned to AHCI ports show up in
'/proc/interrupts' as 'ahci'. This fix adds port numbers as
suffixes and hence makes the descriptions distinct.
Reported-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Jeff moved on to a greener pasture.
s/Maintained by: Jeff Garzik/Maintained by: Tejun Heo/g
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Take advantage of multiple MSIs implementation on x86 - on
systems with IRQ remapping AHCI ports not only get assigned
separate MSI vectors - but also separate IRQs. As result,
interrupts generated by different ports could be serviced on
different CPUs rather than on a single one.
In cases when number of allocated MSIs is less than requested
the Sharing Last MSI mode does not get used, no matter
implemented in hardware or not. Instead, the driver assumes the
advantage of multiple MSIs is negated and falls back to the
single MSI mode as if MRSM bit was set (some Intel chips
implement this strategy anyway - MRSM bit gets set even if the
number of allocated MSIs exceeds the number of implemented ports).
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/15bf7ee314dd55f21ec7d2a01c47613cd8190a7c.1353324359.git.agordeev@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On many architectures, drivers are supposed to prepare/unprepare &
enable/disable functional clock of device. This patch adds clock support for
ahci_platform.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Device Sleep is a feature as described in AHCI 1.3.1 Technical Proposal.
This feature enables an HBA and SATA storage device to enter the DevSleep
interface state, enabling lower power SATA-based systems.
Aggressive Device Sleep enables the HBA to assert the DEVSLP signal as
soon as there are no commands outstanding to the device and the port
specific Device Sleep idle timer has expired. This enables autonomous
entry into the DevSleep interface state without waiting for software
in power sensitive systems.
This patch enables Aggressive Device Sleep only if both host controller
and device support it.
Tested on AMD reference board together with Device Sleep supported device
sample.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Reviewed-by: Aaron Lu <aaron.lwe@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make ahci_dev_classify available to the ahci platform driver for custom
hard reset function.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We will need this macro in both ahci.c and ahci_platform.c, so just move it
to the header.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
The following commit was intended to fix problems with specific AHCI
controller(s) that would become bricks if the AHCI specification was not
followed strictly (that is, if ahci_start_engine() was called while the
controller was in the wrong state):
commit 7faa33da9b
ahci: start engine only during soft/hard resets
However, some devices currently have issues with that fix, so we must
implement a flag that delays the ahci_start_engine() call only for specific
controllers.
This commit simply introduces the flag, without enabling it in any driver.
Note that even when AHCI_HFLAG_DELAY_ENGINE is not enabled, this patch does
not constitue a full revert to commit 7faa33da; there is still a change in
behavior to the ahci_port_suspend() failure path.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
ahci_sb600_softreset was in ahci.c. This function is used
to fix soft reset failure and renames as ahci_pmp_retry_softreset
in libahci.c.
Signed-off-by: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds an sysfs attribute 'em_message_supported' to the
ahci host device which prints out the supported enclosure management
message types.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Commit 6b7ae9545a (libata: reimplement link power
management) removed the check of ATA_FLAG_LPM but neglected to remove the flag
itself. Do it now...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
All checks of ATA_FLAG_NO_LEGACY have been removed by the commits
c791c30670 ([libata] minor PCI IDE probe
fixes and cleanups) and f0d36efdc6 (libata:
update libata core layer to use devres), so I think it's time to finally
get rid of this flag...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 0d5ff56677 (libata: convert to iomap)
removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself.
Do it now, at last...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for Acard ATP8620 host controller.
Based upon initial version by Jeff Garzik.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA devices don't send D2H Reg FIS after an successful ATA PIO data-in
command. The host is supposed to take the TF and E_Status of the
preceding PIO Setup FIS. Update ahci_qc_fill_rtf() such that it takes
TF + E_Status from PIO Setup FIS after a successful ATA PIO data-in
command.
Without this patch, result_tf for such a command is filled with the
content of the previous D2H Reg FIS which belongs to a previous
command, which can make the command incorrectly seen as failed.
* Patch updated to grab the whole TF + E_Status from PIO Setup FIS
instead of just E_Status as suggested by Robert Hancock.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Mark Lord <kernel@teksavvy.com>
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The current LPM implementation has the following issues.
* Operation order isn't well thought-out. e.g. HIPM should be
configured after IPM in SControl is properly configured. Not the
other way around.
* Suspend/resume paths call ata_lpm_enable/disable() which must only
be called from EH context directly. Also, ata_lpm_enable/disable()
were called whether LPM was in use or not.
* Implementation is per-port when it should be per-link. As a result,
it can't be used for controllers with slave links or PMP.
* LPM state isn't managed consistently. After a link reset for
whatever reason including suspend/resume the actual LPM state would
be reset leaving ap->lpm_policy inconsistent.
* Generic/driver-specific logic boundary isn't clear. Currently,
libahci has to mangle stuff which libata EH proper should be
handling. This makes the implementation unnecessarily complex and
fragile.
* Tied to ALPM. Doesn't consider DIPM only cases and doesn't check
whether the device allows HIPM.
* Error handling isn't implemented.
Given the extent of mismatch with the rest of libata, I don't think
trying to fix it piecewise makes much sense. This patch reimplements
LPM support.
* The new implementation is per-link. The target policy is still
port-wide (ap->target_lpm_policy) but all the mechanisms and states
are per-link and integrate well with the rest of link abstraction
and can work with slave and PMP links.
* Core EH has proper control of LPM state. LPM state is reconfigured
when and only when reconfiguration is necessary. It makes sure that
LPM state is reset when probing for new device on the link.
Controller agnostic logic is now implemented in libata EH proper and
driver implementation only has to deal with controller specifics.
* Proper error handling. LPM config failure is attributed to the
device on the link and LPM is disabled for the link if it fails
repeatedly.
* ops->enable/disable_pm() are replaced with single ops->set_lpm()
which takes @policy and @hints. This simplifies driver specific
implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Link power management related symbols are in confusing state w/ mixed
usages of lpm, ipm and pm. This patch cleans up lpm related symbols
and sysfs show/store functions as follows.
* lpm states - NOT_AVAILABLE, MIN_POWER, MAX_PERFORMANCE and
MEDIUM_POWER are renamed to ATA_LPM_UNKNOWN and
ATA_LPM_{MIN|MAX|MED}_POWER.
* Pre/postfixes are unified to lpm.
* sysfs show/store functions for link_power_management_policy were
curiously named get/put and unnecessarily complex. Renamed to
show/store and simplified.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata depends on scsi_host_template for module reference counting and
sht's should be owned by each low level driver. During libahci split,
the sht was left with libahci.ko leaving the actual low level drivers
not reference counted. This made ahci and ahci_platform always
unloadable even while they're being actively used.
Fix it by defining AHCI_SHT() macro in ahci.h and defining a sht for
each low level ahci driver.
stable: only applicable to 2.6.35.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
88SE9128 can do FBS and sets it in HOST_CAP but forgets to set FBSCP
in PORT_CMD. Implement AHCI_HFLAG_YES_FBS and apply it to 88SE9128.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add "em_buffer" attribute for SATA AHCI hosts to provide a way for
userland to access AHCI EM (enclosure management) buffer directly if the
host supports EM.
AHCI driver should support SGPIO EM messages. However the SATA/AHCI
specs did not define the SGPIO message format filled in EM buffer.
Different HW vendors may have different definitions. The mainly purpose
of this attribute is to solve this issue by allowing HW vendors to
provide userland drivers and tools for their SGPIO initiators.
Signed-off-by: Harry Zhang <harry.zhang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Detect enclosure management message type automatically at driver
initialization, instead of using module parameter "ahci_em_messages".
Signed-off-by: Harry Zhang <harry.zhang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It turns out different generations of MCPs have differing quirks.
* MCP 65-73 : FPDMA AA broken, lies about PMP support, forgets to report NCQ
* MCP 77-79 : FPDMA AA broken, lies about PMP support
* MCP 89 : FPDMA AA broken
Instead of turngin off FPDMA AA on all NVIDIAs, implement
HFLAG_NO_FPDMA_AA, define additional board IDs and apply necessary
quirks.
This fixes bko#15481 and the list of quirks is verified by Peer Chen.
http://bugzilla.kernel.org/show_bug.cgi?id=15481
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch should contain no functional changes, just moves code
around.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
