direct dereferencing from user-supplied address
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since:
1) FW_LOADER is defined as:
config FW_LOADER
tristate "Userspace firmware loading support"
depends on HOTPLUG
2) several V4L/DVB driver just selects it;
3) select is not smart enough to auto-select HOTPLUG, if select FW_LOADER.
So, All drivers that select FW_LOADER should also depend on HOTPLUG.
An easier solution (for the end-user perspective) would be to "select HOTPLUG".
However, live is not simple. This would cause recursive dependency issues like
this one:
drivers/usb/Kconfig:62:error: found recursive dependency: USB -> USB_OHCI_HCD
-> I2C -> MEDIA_TUNER -> MEDIA_TUNER_XC2028 -> HOTPLUG -> PCCARD -> PCMCIA ->
USB_ARCH_HAS_HCD -> MOUSE_APPLETOUCH -> USB
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Activy budget card with BSBE1 tuner, subsystem id 0x1131:0x4f60.
Low band and DiSEqC support should work now (BSBE1 and BSRU6 tuner).
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some DVB-S boards, i.e. with the SD1878 tuner, use a 4 MHz reference frequency.
This reqires a different setup of the clock PLL.
This patch adds an enum to the tda10086_config struct and sets the proper
values for the boards.
This patch also fixes the DVB-S section of the MD7134_BRIDGE_2
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This device is a clone of the PN1010 used by SkyStar2 rev2.7 .
This patch adds support for the flexcop-device and makes the driver look a little bit nicer.
It needs to be checked whether the driver is still ok for the budget-cards.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The adapter_nr module options can be used to allocate static adapter
numbers on a driver level. It avoids problems with changing DVB apapter
numbers after warm/cold boot or device unplugging and repluging.
Each driver holds DVB_MAX_ADAPTER long array of the preferred order of
adapter numbers.
options dvb-usb-dib0700 adapter_nr=7,6,5,4,3,2,1,0 would result in a
reversed allocation of adapter numbers.
With adapter_nr=2,5 it tries first to get adapter number 2 and 5. If
both are already in use it will allocate the lowest free adapter number.
Signed-off-by: Janne Grunau <janne-dvb@grunau.be>
Acked-by: Hermann Pitton <hermann.pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement support for Fujitsu Siemens DVB-T Activy Budget, sub-system id 0x1131:0x5f61.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Quoting the commit introducing reinitialise_demod (3984 / by adq):
"These cards [KNC1 DVBT and DVBC] need special handling for CI - reinitialising the frontend
device when the CI module is reset."
Apparently my 1894:0010 also needs that fix, because once you initialise CI/CAM you lose lock.
Signed-off-by: Christoph Pfister <pfister@linuxtv.org>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The current ci implementation doesn't accept 0xff when reading data bytes (address == 0),
thus breaks cams which report a buffer size of 0x--ff like my orion one.
Remove the 0xff check altogether, because validation is really the job of a higher layer.
Signed-off-by: Christoph Pfister <pfister@linuxtv.org>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Static memory is always initialized with 0.
- Replaced in some cases C99 comments for /* */
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some cards need the diseqc signal modulated, while some just need
the envelope to control the LNB supply.
This fixes Bug 9887
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Improved display of still pictures (VIDEO_STILLPICTURE ioctl).
Ensure that both fields are displayed for progressive frames.
Thanks to Reinhard Nissl and Klaus Schmidinger for finding out
that the FREEZE command does this.
Thanks-to: Reinhard Nissl <rnissl@gmx.de>
Thanks-to: Klaus Schmidinger <Klaus.Schmidinger@cadsoft.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for KNC TV Station Plus X4, sub-system id 0x1894:0x0015.
Based on a patch submitted by Johannes Deisenhofer.
Thanks-to: Johannes Deisenhofer <jo.deisenhofer@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ttpci Kconfig file has bugs that cause it to fail in certain Kconfig
situations. The basic problem is that it selects certain drivers, but does
not depend on the dependencies of those drivers.
See http://article.gmane.org/gmane.comp.video.video4linux/35072
Using the Kconfig file also has some annoyances. For instance one can't turn
off AV7110 support unless you go down several options and first turn off
budget-patch support. Normally user selectable drivers are not forced on like
this.
The "AV7110 cards with Budget Patch" option is disabled if "Budget cards"
isn't on. Normally a driver appears nested under a driver it depends on, but
since drivers that don't depend on "Budget cards" are between the two options,
the config programs can't display the tree correctly.
The Makefile has an issue too. Some modules, ttpci-eeprom and budget-core,
appear in the Makefile under several different config symbols. If more than
one of these symbols is on, they will get added the to list of objects
multiple times. The normal convention is to have a config symbol just the
common object(s) and have the users of the that object either depend on or
select that config symbol.
This patch fixes all these issues. ttpci-eepom is under a new config symbol,
and so is the budget-core module. The four different budget card types appear
as sub-drivers under a main "SAA7146 DVB cards" option. Turning on
budget-patch doesn't force AV7110. Drivers using SAA7146_VV have the
necessary VIDEO_DEV dependency, so that it isn't possible to select SAA7146_VV
without V4L being on.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix driver data name to match whitelist of acceptable names that contain
pointers init data so that section mismatch warning is placated.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All of these drivers select VIDEO_IR, which uses the input subsystem,
so they should also depend on INPUT.
Problem examples:
drivers/built-in.o: In function `ir_input_key_event':
ir-functions.c:(.text+0x10849a): undefined reference to `input_event'
ir-functions.c:(.text+0x1084ac): undefined reference to `input_event'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11cc0a): undefined reference to `get_key_pinnacle_color'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11cc4f): undefined reference to `get_key_pinnacle_grey'
drivers/built-in.o: In function `saa7134_input_fini':
(.text+0x11cd8b): undefined reference to `input_unregister_device'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11d1fa): undefined reference to `input_allocate_device'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11d317): undefined reference to `input_register_device'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11d6ca): undefined reference to `input_free_device'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c3f3): undefined reference to `ir_codes_hauppauge_new'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c450): undefined reference to `ir_codes_pinnacle_color'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c480): undefined reference to `ir_codes_purpletv'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c495): undefined reference to `ir_codes_pinnacle_grey'
drivers/built-in.o: In function `saa7134_ir_start':
(.text+0x11c622): undefined reference to `ir_rc5_timer_end'
drivers/built-in.o: In function `saa7134_ir_start':
(.text+0x11c637): undefined reference to `ir_rc5_timer_keyup'
drivers/built-in.o: In function `build_key':
saa7134-input.c:(.text+0x11c769): undefined reference to `ir_extract_bits'
saa7134-input.c:(.text+0x11c7ad): undefined reference to `ir_input_keydown'
saa7134-input.c:(.text+0x11c7f0): undefined reference to `ir_input_keydown'
saa7134-input.c:(.text+0x11c7f9): undefined reference to `ir_input_nokey'
saa7134-input.c:(.text+0x11c806): undefined reference to `ir_input_nokey'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ca07): undefined reference to `ir_codes_encore_enltv'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11caf6): undefined reference to `ir_input_init'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cbf2): undefined reference to `ir_codes_avermedia'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cc24): undefined reference to `ir_codes_pctv_sedna'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cc53): undefined reference to `ir_codes_flydvb'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cc85): undefined reference to `ir_codes_videomate_tv_pvr'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ccb7): undefined reference to `ir_codes_pixelview'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cce9): undefined reference to `ir_codes_eztv'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cd1b): undefined reference to `ir_codes_manli'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cda8): undefined reference to `ir_codes_cinergy'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cdd7): undefined reference to `ir_codes_flyvideo'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ce06): undefined reference to `ir_codes_asus_pc39'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ce7d): undefined reference to `ir_codes_gotview7135'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cee1): undefined reference to `ir_codes_proteus_2309'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
remove asm/bitops.h includes
including asm/bitops directly may cause compile errors. don't include it
and include linux/bitops instead. next patch will deny including asm header
directly.
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There were many instances of 7-space indents spread throughout
the v4l-dvb tree.
This patch replaces the 7-space indents with tabs. The whitespace cleaner
script doesn't catch these, because it assumes that all indents are 8-space.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
vmalloc() returns void * - no need to cast it.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since at least kernel 2.6.12-rc2, module.h includes moduleparm.h. This
patch removes all occurences of moduleparm.h from drivers/media files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch replaces an array size calculation done using sizeof
with an invocation of the ARRAY_SIZE macro.
Tested by compilation on an i386 box using "allyesconfig".
Diffed against Linus' git-tree.
Signed-off-by: Andi Drebes <lists-receive@programmierforen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert av7110_v4l.c to use i2c_transfer() instead of saa7146_i2c_transfer().
Make saa7146_i2c_transfer() static.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Parse error in ifdef or bad use of macro.
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Re-initialize aspect ratio and pan scan after arm crash.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes all static dependencies on the dvb-pll module.
All exported dvb_pll_desc's have been UNexported, and the caller
will reference the individual dvb_pll_desc by it's index in the
pll_list array.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The Makefiles in the dvb directory tree used '=' when defining EXTRA_CFLAGS
rather than '+=', which is far more common in the rest of the kernel source.
= 14 times (9 of which this patch removes)
:= 25 times
+= 123 times
This change also has certain advantages for the out of kernel v4l-dvb build
system.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In preparation for struct class_device -> struct device input
core conversion switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor at mail.ru>
Acked-by: Thierry Merle <thierry.merle@free.fr>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename dvb_pll_desc.setbw() to set(), and accept struct dvb_frontend_parameters
instead of passing both freq and bandwidth, so that this may be used as a
generic function.
In order to do this, dvb_pll_configure must also be altered in the same manner,
to take struct dvb_frontend_parameters instead of freq and bandwidth.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
if the call to budget_register() fails in ttpci_budget_int(),
ttpci_budget_init() returns success. The attached patch will
fix this problem.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Revert changeset
http://linuxtv.org/hg/v4l-dvb?cmd=changeset;node=e7c424bbf9aa;style=gitweb
Petri Helin found that this changeset broke tuning:
'Well, after going through the changes that might have had effect on
tuning, I found out the one which had caused this problem. I do not know
the actual reason behind the change, but the changelog says that it
was meant to "Fix TD1316 tuner for DVBC". But at least in my case it
seams to have broken the tuner instead.'
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Thanks-to: Petri Helin <phelin@googlemail.com>
Acked-by: e9hack <e9hack@googlemail.com>
Acked-by: Thomas Kaiser <linux-dvb@kaiser-linux.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I added saa7146_vmalloc_destroy_pgtable() which frees the resources
allocated by saa7146_vmalloc_build_pgtable() and updated the callers in
budget-core.c and av7110.c. I have also been through the updated
functions and updated the error paths to ensure they free all allocated
resources on error.
I also realised that there are other callers to saa7146_pgtable_free()
which did not have any sg DMA mapped so it seems wrong to add the
pci_unmap_sg() into that function. Instead I created
saa7146_vmalloc_destroy_pgtable() to do this.
Also included in this patch are the previous fixes for pci_unmap_sg()
and syncing the PCI streamed data to work with a SWIOTLB and match the
requirements documented in DMA-API.txt.
Signed-off-by: Jon Burgess <jburgess777@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the inversion setting configurable. The KNC ONE V1.0 uses
non inverted setting for the inversion and add the KNC ONE V1.0 card.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the frontend TDA10023 and add cards that need the
tda10023.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Georg Acher <acher@in.tum.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the polarity switching of the clock for the DVB-C cards in
budget-av.c. This hack is no longer necessary because the saa7146 can
do the job to remove the additional FEC bytes from the TS.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix bug introduced during infrared refactoring.
Thanks to Johann Friedrichs for spotting this.
Thanks-to: Johann Friedrichs <johann.friedrichs@web.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In transfer/replay mode the frontend lock status was never updated.
This caused a 'black screen' if VDR switched from transfer mode to
live mode on the same transponder.
Thanks to Marco Schluessler for spotting the problem.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A number of drivers selected DVB_PLL when they did not need it, and some
that did need it did not select it.
The DVB_PLL option is given a name and help text, so that it will show up
in the config menu. DVB_PLL support can be turned on if an out-of-tree
driver needs it.
The standard dvb fe customization support is added to dvb-pll.h. Since
all modules which select DVB_PLL do so unconditionally, it is not
possible to turn dvb-pll off when an enabled module selects it, unlike
most of the other frontend/tuner drivers. This is because the users of
dvb-pll have static references to dvb-pll symbols other than the attach
function. If these references are removed, then dvb-pll will be
disablable as the other frontend/tuner drivers are.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support for MSC_RAW and MSC_SCAN remote control events.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The attached patch contains the last set of changes to the budget-ci IR
handling which makes it use the repeat handling of the input subsystem.
This allows some code simplification, makes sure that repeat key presses
are reported as such and also allows the "debounce" hack to be removed
altogether.
In addition a couple of static variables were removed which would have
confused the IR code if more than one card is used.
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Infrared remote control support rewritten.
Now each device provides its own event device, keymap, protocol,
inversion and address setting.
EVIOCGKEYCODE and EVIOCSKEYCODE ioctls are supported to read/modify
a keymap. Keymaps may be loaded using
- input tools (keyb etc.)
- av7110_loadkeys (obsolete, for backward compatibility)
New command line parameters:
- ir_protocol: select infrared protocol: 0 RC5, 1 RCMM (default)
- ir_inversion: signal inversion: 0 not inverted (default), 1 inverted
- ir_device_mask: bitmask of infrared devices (default: accept all)
Those parameters may be set anytime.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx23415 adds some extra features that this DVB decoding API did
not support. This API has been expanded to support the required
features. Both source and binary backwards compatibility is kept
intact by these changes. So existing applications are not affected.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Commit 00c4cc6751 Oliver Endriss changed
the budget-ci driver to use interrupt mode for i2c transfers.
This also meant that a new bunch of IR bytes that were previously lost
are now received, which allowed me to better understand how the MSP430
chip works. Unfortunately it also means that the current driver gets
some assumptions wrong and might generate double keypresses for one IR
command.
The attached patch fixes this by throwing away the repeat bytes and by
associating the correct command and device bytes.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
dvb kernel_thread to kthread API port.
It is running fine here, including module load/unload and software suspend
(which doesn't work as expected with or without this patch :).
I didn't convert the dvb_ca_en50221 as I do not have such an interface, but
if the conversion process is fine with the v4l-dvb maintainers, it should not
be a problem to send a patch for that too ...
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Herbert Poetzl <herbert@13thfloor.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use ARRAY_SIZE macro already defined in kernel.h
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixed problem reported by Teemu Suikki:
After a device with subsystem 0x13c2:0x1012 has been installed,
devices with subsystem id 0x13c2:0x1011 did not work anymore.
Reason:
The driver for 0x13c2:0x1012 modified shared configuration data.
Fix:
Use separate configuration data for those devices.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
input_register_device() was changed to return an error code instead of
being void in 2.6.15. Handle it with a macro wrapper in config.h. For
this to work, linux/input.h must be included before config.h. This
required some trivial header re-ordering in budget-ci.c and ttusb_dec.c.
In kernel 2.6.15-rc1 a helper function called setup_timer() was added to
linux/timer.h. Add to compat.h, but require that linux/timer.h be
included first to give the definition of struct timer_list.
A new 4GB DMA zone, __GFP_DMA32, was added in 2.6.15-rc2. Alias it to
__GFP_DMA on older kernels.
Handle another 2.6.15 "input_dev->dev to input_dev->cdev.dev" change for
some recently added code in cinergyT2.c.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixed unregistering the vbi device for cards without analog tuner.
Thanks to Marco Schluessler <marco@lordzodiac.de> for pointing out this bug.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add phys-string, bustype, version, vendor and product to help udev and
others using EVIOCPHYS ioctl to identify the input device node.
Code taken (with little changes) from budget-ci.c
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The keymap is based on a previous patch by Jussi Kukkonen.
This remote is identified by subsystem_device id 0x1010.
Signed-off-by: Ville-Pekka Vainio <vpivaini@cs.helsinki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove bogus read during MC1 programming.
A '1' bit could never be cleared using the old code.
Use MASK_xx macros.
Signed-off-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use SAA7146_IER_ENABLE/DISABLE to enable or disable a hardware interrupt.
Signed-off-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added a delay to give the frontend a little bit time for power-on.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/dvb/ttpci/budget-ci.c:220:6: warning: "LINUX_VERSION_CODE" is not defined
drivers/media/dvb/ttpci/budget-ci.c:220:28: warning: "KERNEL_VERSION" is not defined
drivers/media/dvb/ttpci/budget-ci.c:220:42: error: missing binary operator before token "("
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This caused compilation to fail - completely replaced by new style
functions, so can be removed.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If your device is using the philips tda1316 tuner, i think there is a
problem in setting the correct Band. 162 MHz and above should be band 2
(Mid-Band). But in dvbc_philips_tdm1316l_tuner_set_params band 1 is set
for frequencies below 200 MHz.
Signed-off-by: Thomas Kaiser <linux-dvb@kaiser-linux.li>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change the debounce logic so that it is not used at all unless the
debounce parameter has been set. This makes for a much "snappier" remote
for most users as there is no timeout to wait for (the debounce logic has
a 350ms timer for the next repeat, but with the RC5 protocol, one event
per ~110ms is possible)
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds a ir_debug parameter which is useful in tracking down
IR decoding problems.
Based on Darren Salt's dvb-ir patchset.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Decode the RC5 device byte as well as the command byte. Introduce a
parameter to set the device events to listen for. Default to try
to auto-detect the proper device code, otherwise, listen to any
device as the old code did.
Based on Darren Salt's dvb-ir patchset.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This converts the budget-ci driver so that it uses ir-common for some of its
IR processing. In particular, the keymap for the Nova-T (sub 13c2:1011) is
switched to the Hauppauge grey/black keymap, of which the keys on the
supplied R808 remote control form a subset.
The old budget-ci keymap is moved to ir-keymaps.c and is used for other
remotes.
The debounce logic for buggy remotes (i.e. Zenith) is made conditional the
new debounce parameter and defaults to off (so that repeat keypresses aren't
ignored for all working remotes).
Some parts are based on Darren Salt's dvb-ir patchset.
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trivial change to help the user understand what went wrong.
Taken from Darren Salt's dvb-ir patchset.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Improve the error checking in the IR init and deinit functions.
Based on Darren Salt's dvb-ir patchset.
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds a 'phys' string, of the same form as used by various other
DVB cards' IR drivers, for access by any program which uses the EVIOCPHYS
ioctl or may read /sys/class/input/*/phys (e.g. udev) to identify input
device nodes.
Taken from Darren Salt's dvb-ir patchset.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch lays down some groundwork for later budget-ci patches. The bulk
of this consists of moving a few members into a new struct and renaming a
few of them.
It also allocates extra space for the device name (the "name" field in
/proc/bus/input/devices and in the relevant sysfs dir) to avoid truncation
and uses snprintf rather than sprintf in case the extra space shouldn't be
enough.
Taken from Darren Salt's dvb-ir patchset
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- adhere to 80-column limit
- replace some spaces with tabs
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For some reason, some of these cards have the tda10021 configured to a
different address. This adds support for such cards
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also sprinkled some input_sync() throughout the code.
Acked-by: Ricardo Cerqueira <v4l@cerqueira.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Satelco EasyWatch PCI DVBC cards
Signed-off-by: Thomas Hamm <thhamm@t-online.de>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix various .c/.h typos in comments (no code changes).
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
New module parameter diseqc_method for cards with subsystem-id 13c2:1003.
- 0: unreliable method, can be used by all board revisions (default)
- 1: reliable method, works for newer board layouts only
The parameter has no effect for cards with other subsystem-ids.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixes to DISEQC on these cards inadvertently broke normal tone/voltage
signalling. This restores the necessary function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Technotrend 1500 T card have "inverted inversion". This patch fixes that.
Many thanks to Martin Zwickel from Technotrend for his confirmation and
correction proposal.
Signed-off-by: Raymond Mantchala <raymond.mantchala@streamvision.fr>
Signed-off-by: Perceval Anichini <perceval.anichini@streamvision.fr>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The IR chip has no address decoding, so the IR data is always present in
the high byte when doing a read from the saa7146 chip. This means that
the DEBI address used is irrelevant to the IR decoding logic.
DEBI addresses 0x1XXX are mapped to the registers on the CI module
itself, but only the lowest two bits are actually used (see EN50221,
section A.2.2.1), meaning that 0x1234 is equivalent to 0x1000 which maps
to register 0 (the data register). A read from the data register is
supposed to be preceded by a read from the size register, so some CI
modules will be confused (the AlphaCrypt CAM will hang completely).
The attached patch changes the address used when reading the IR data to
use 0x4000 instead. This is the CI version address, which is a safer
default, works with the AlphaCrypt CAM and matches the behaviour of the
Windows driver (AFAIK).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement fix suggested by Michael Hunold for a bug reported
by Philipp Matthias Hahn: Starting "kdetv" on a Siemens DVB-C 1.x
produced an oops because kdetv opened "/dev/vbi0".
Remove the V4L2_CAP_VBI_CAPTURE flag because it does not work with
this type of hardware anyway.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Do not select FW_LOADER unless it is really required.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Port budget-av to use the new tua6100 driver
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Apparently there are two types of knc1 dvb-s plus cards with different tuners
(as for the knc1 dvb-s ones). This patch adds support for those cards with
subsystem id 1894:0011.
Successfully tested by: Benjamin Weber <benny1990@gmail.com>
Signed-off-by: Christoph Pfister <christophpfister@gmail.com>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This actually needs the same configuration as the other DVBC cards; simply
no one had managed to test before to find out.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
DVB null terminates its device names, which seems odd, and should be
unnecessary.
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some DVB-T cards with Grundig 29504-401 tuner use subsystem id 13c2:0001
(reported by Stuart Butterfield).
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I missed one call during the dvb_attach() development.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add the necessary code and makefile infrastructure
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only devices using > 1 frontend were ported; ones which did not are left
using static binding.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rewrote _write() calls to use write() op.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert SEC drivers to new frontend API
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since av7110.c is the only file actually using something from this
header, there's no reson for other files to
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several DVB modules depends on I2C
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix bug reported by Andrew de Quincey:
After cold boot the saa7146 DMA did not start if the demuxer was opened
before the frontend has locked to the signal.
DMA transfers will be started now if (and only if)
the frontend is locked and data should be sent to the demuxer.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix typo in comment for TDA9819
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the stv0299 native DISEQC implementation instead of the bitbanging one
as required by the ves1893. This was originally found by Oliver Endriss.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The original driver had a restriction that if a card as an saa7113 chip,
then it cannot have a CI interface. This is not the case.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These cards do not need the tda10021 configuration change when data is
streamed through a CAM module. This disables it for these ones.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for the msp34x5 audio dac. Analog sound output of
Technotrend DVB-C 2300 (aka Hauppauge Nexus-CA) works now.
Signed-off-by: Tim Kaiser <timkaiser@t-online.de>
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix missing $() on variable name in dvb/ttpci/Makefile
Fix AV7110 firmware dependencies so that parallel builds work correctly.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for Satelco EasyWatch DVB-S light card,
a clone of the KNC 1, with PCI subsystem ID 1894:001e
Signed-off-by: Lothar Englisch <Lothar.Englisch@lycos.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The dvb_frontend_ops is a pointer inside dvb_frontend. That's why every demod-driver
is having a field of dvb_frontend_ops in its private-state-struct and
using the reference for filling the pointer-field in dvb_frontend.
- It saves at least two lines of code per demod-driver,
- reduces object size (one less dereference per frontend_ops-access),
- be coherent with dvb_tuner_ops,
- makes it a little bit easier for newbies to understand how it works and
- avoids stupid mistakes because you would have to copy the dvb_frontend_ops
always, before you could assign the static pointer directly, which was
dangerous.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These cards need special handling for CI - reinitialising the frontend
device when the CI module is reset. Additionally the tda10021 needs to be set
into a different transport stream mode when a CI module is present.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added config switch to stv0297 to control i2c STOP during write behaviour.
Update frontend init in dvb-ttusb-budget.
Enable i2c STOP on other users of stv0297.
Signed-off-by: Thomas Kaiser <linux-dvb AT kaiser-linux.li>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert lnbp21.h into a linux kernel module.
Fix up previous users to use it.
Convert dvb-ttusb-budget to use it.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some systems use a previous config information to generate
a default config. This seems to cause troubles on some
systems.
This patch also fixes compilation for AV7110 firmware
inside V4L/DVB tree.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Don't try and set the tuner ops if the demod was not detected.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since I reordered the CI/frontend detection, it turns out the frontend needs
to have a GPIO set to power it on; otherwise frontend init fails.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently in /sys/class/dvb/dvbX.demuxY/ we have:
dev
uevent
With the patch, we have (for a PCI DVB device):
dev
device -> ../../../devices/pci0000:00/0000:00:1e.0/0000:03:0d.0
uevent
So userspace tools can (finally) work out which physical device a DVB adapter
refers to. Previously you had to kinda look through dmesg and hope that it
hadn't been dumped out of the buffer. This makes debugging a lot easier if
the system has been up for a long time!
This is done by adding an extra 'struct device *' parameter to
dvb_register_adapter(). It will work with any kind of standard
linux 'device'. Additionally, if someone has an embedded system which does
things differently, they can simply supply 'NULL' and the behaviour will be
as before - the link will simply not appear.
Ack'd-by: Manu Abraham <manu@linuxtv.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If you have more than DVB_MAX_ADAPTERS in your machine, this causes an oops.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L1 API is depreciated and should be removed soon from kernel. This patch
adds two new options, one to disable V4L1 drivers, and another to disable
V4L1 compat module. This way, it would be easy to check what still depends
on V4L1 stuff, allowing also to test if app works fine with V4L2 only support.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that the CI code reinitialises the frontend, need to move the CI
initialisation to after the frontend init in order to ensure the frontend is
always in a good state. Fixes an oops caused by the frontend being NULL as
well.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It turns out the firmware on the TT budget-ci 1.1 slots doesn't generate
interrupts. This patch adds support for this using polling mode on these
slots.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Unfortunately on the budget-av board, the CAM reset line is tied to the
frontend reset line, so resetting the CAM also zaps the frontend. This
breaks the tda1004x at least, and causes it to fail to tune until the
budget-av module is reloaded. This patch adds an exported function to dvb_frontend
that allows a card to forcibly reinitialise a frontend. The budget-av now
does this on CAM reset, which corrects this problem.
since they do not tie the CAM reset line to the frontend reset line.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This attached patch was originally proposed by Anssi Hannula to the dvb-kernel
user to choose the default broadcast mode when using the ttpci driver.
NTSC users need to only add the following line to modprobe.d:
options dvb-ttpci tv_standard=1
PAL users will not need to change anything, for this will be the default.
Signed-off-by: C.Y.M <syphir@syphir.sytes.net>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes a typo in a comment.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Issue a warning when more than 80% of the DMA buffer is being used
(probably due to bad IRQ latency). Warnings are rate-limited.
- Introduce a new parameter 'bufsize' (in KByte) which increases the
default DMA buffer of 188 KByte up to 1410 KByte (Activy: 564 KByte).
Signed-off-by: Ingo Schneider <mail@ingo-schneider.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a new audio mode V4L2_TUNER_MODE_LANG1_LANG2 (used by VIDIOC_G/S_TUNER).
This mode allows the user to select both languages of a bilingual transmission,
one language on the left, one on the right audio channel. If there is no
bilingual transmission, or it is not supported, then this mode should act like
V4L2_TUNER_MODE_STEREO.
This mode is introduced for PVR-like drivers where it is useful to be able to
record both languages of a bilingual broadcast.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add wss_cfg_4_3 and wss_cfg_16_9 configuration options.
Firmware 2623 or later required.
Both parameters are bit masks:
- bit 15: disable WSS
- bit 14: send short WSS burst, then turn off WSS
- bit 13..0: WSS bits as specified by the standard
These parameters are useful if you own a broken tv set which
does not handle wss correctly.
Default settings:
- wss_cfg_4_3: 0x4008
- wss_cfg_16_9: 0x0007
These should work with most devices.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moved duplicated code of ALPS BSRU6 tuner to a standalone file.
Modified av7110 and budget drivers to include the new file.
Signed-off-by: Perceval Anichini <perceval.anichini@streamvision.fr>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Typos grab bag of the month.
Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use refactored LNBP21/BSBE1 code for Technotrend/Hauppauge DVB-S rev 2.3.
As a side effect, FE_ENABLE_HIGH_LNB_VOLTAGE ioctl is supported now.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moved duplicated code to separate files.
LNBP21 stuff rewritten from scratch, BSBE1 copied from av7110.c.
Modified budget driver to use the new routines.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Workaround for Nexus CA: Debi test fails unless first debi write is repeated.
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
use __devinit/__devexit/__devexit_p() where appropriate
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Make needlessly global code static
- #if 0 the following unused global functions:
- b2c2/flexcop-dma.c: flexcop_dma_control_packet_irq()
- b2c2/flexcop-dma.c: flexcop_dma_config_packet_count()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- BOOT_SIZE name is also used at alpha and were breaking
compiling with allyesconfig.
- All BOOT_* renamed to AV7110_BOOT* to fix and keep names
with the same style.
Thanks to Andrew Morton for pointing this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Static vars are equal to zero by default. Removed unnecessary =0 from them,
saving some data space
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added knc1 tv star dvb-s support with philips tuner sd1878.
Signed-off-by: Regis Prevot <regis.prevot@anevia.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Implemented v4l2 api for sliced vbi data output
to pass WSS data from userspace to the av7110
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Reverted objectionable fix in saa7146_hlp.c
- Merged in improved dvb 64-bit fixes from Peter Beutner.
Signed-off-by: Peter Beutner <p.beutner@gmx.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Improved recovery from ARM crash and the way a crash is detected.
Minor white space clean-up, debug output fixed.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- make the firmware dir documentation and comments consistent in the v4l-dvb tree.
Signed-off-by: Ville Skyttä <ville.skytta@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Adds a time-delay to IR remote button presses for av7110_ir input,
such that it acts more like a keyboard. A short press will be treated
as a single button press. Holding down a button on the remote will
respond like holding down a key on the keyboard, and result in a
key-repeat. This just introduces a delay between the 1st press, and
going into key-repeat so that it is possible to get a single 'up'.
Signed-off-by: Noone Important <nxhxzi702 at sneakemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Port code for SU1278/SH2 (TUA6100) from pre-refactored code
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Driver support for live-ac3, firmware >= 2621 required.
Signed-off-by: Dr. Werner Fink <werner@suse.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- LNB power can now be switched off for Activy Budget-S rev GR/AL.
Dishnetwork support fixed for Nova-S with bsbe1/lnbp21 frontend and
Activy Budget-S rev AL.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Fixes for the topuptv/SCM mediaguard CAM module in KNC1 CI module
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Now when kbuild passes KBUILD_MODNAME with "" do not __stringify it when
used. Remove __stringnify for all users.
This also fixes the output of:
$ ls -l /sys/module/
drwxr-xr-x 4 root root 0 2006-01-05 14:24 pcmcia
drwxr-xr-x 4 root root 0 2006-01-05 14:24 pcmcia_core
drwxr-xr-x 3 root root 0 2006-01-05 14:24 "processor"
drwxr-xr-x 3 root root 0 2006-01-05 14:24 "psmouse"
The quoting of the module names will be gone again.
Thanks to GregKH + Kay Sievers for reproting this.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
- Small cleanups:
- make needlessly global functions static
- every file should #include the headers containing the prototypes for it's
global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
stv0299_set_frontend(): reduced number of i2c transfers, set register 0x12
from inittab
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for the Technotrend Budget Card S1500 with a BSBE1
frontend and the LNBP21.
Signed-off-by: Martin Zwickel <martin.zwickel@technotrend.de>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add PCI-ids of Siemens-DVB-C card with Technotrend manufacturer id.
Signed-off-by: Karl Herz <karl.herz@gmx.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Improved remote control support for av7110-based cards:
o extended rc5 protocol, firmware >= 0x2620 required
o key-up timer slightly adjusted
o completely moved remote control code to av7110_ir.c
o support for multiple ir receivers
o for now, all av7110 cards share the same ir configuration and event device
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable frontend on KNC plus cards.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes for CI interface.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for TT DVB-C CI card.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for analog video inputs (CVBS and Y/C) of the
analog module for the Siemens DVB-C card.
Signed-off-by: thomas schorpp <t.schorpp@gmx.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Misc. fixes.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass a pointer to the i2c bus to the pll callbacks (stv0299 only).
It was not possible to tell which i2c bus should be used if an adapter has
multiple frontends on multiple i2c buses.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes the following compile error:
...
LD .tmp_vmlinux1
drivers/built-in.o: In function `frontend_init':
budget-av.c:(.text+0xb9448): undefined reference to `tda10046_attach'
budget-av.c:(.text+0xb9518): undefined reference to `tda10021_attach'
drivers/built-in.o: In function `philips_tu1216_request_firmware':
budget-av.c:(.text+0xb937b): undefined reference to `request_firmware'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Johannes Stezenbach <js@linuxtv.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The / in the driver name (budget dvb /w video in) is not a valid character for
device names - removed it, now it works!
Same for ttusb-budget.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Timeout handling fixed, especially for preemtible kernels and/or high system
load.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
printk() calls should include appropriate KERN_* constant.
Signed-off-by: Christophe Lucas <clucas@rotomalug.org>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
av7110_fe_lock_fix() modified in a way that it can be retried after
-ERESTARTSYS
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix indentation and add some whitepsace between operators.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change error handling in av7110_stop_feed() to stop as many filters as
possible in case of errors.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o propagate more errors back to caller or log them, mainly in
av7110.c and av7110_av.c
o fix error message in StartHWFilter
o do not StopHWFilter for handle 0xffff
Signed-off-by: Wolfgang Rohdewald <wolfgang@rohdewald.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix for QAM128 in VHF band suggested by Timo Helkiö.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix bug in timeout handling.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o make sure ERESTARTSYS will be propagated
o ReleaseBitmap: starting with Firmware 261e, also release when
BMP_LOADING
o removes unused #define BMP_LOADINGS
o in many cases changed the return value from -1 to something more
meaningful like ETIMEDOUT, EINVAL
o changed syslog message timeout waiting for COMMAND such that it
indicates what command did not complete
o reduce # of arguments for LoadBitmap and BlitBitmap
o av7110_osd_cmd: remove the out: label
Signed-off-by: Wolfgang Rohdewald <wolfgang@rohdewald.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for new TT DVB-T-CI, thanks to Andre Weidemann
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for s5h1420 frontend (new Technotrend/Hauppauge DVB-S SE).
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
