We have various bootloaders for Exynos4210 machines. Some of they
set the ARM core frequency at boot time even when the boot is a resume
from suspend-to-RAM. Such changes may create inconsistency in the
data of CPUFREQ driver and have incurred hang issues with suspend-to-RAM.
This patch enables to save and restore CPU frequencies with pm-notifier and
sets the frequency at the initial (boot-time) value so that there wouldn't
be any inconsistency between bootloader and kernel. This patch does not
use CPUFREQ's suspend/resume callbacks because they are syscore-ops, which
do not allow to use mutex that is being used by regulators that are used by
the target function.
This also prevents any CPUFREQ transitions during suspend-resume context,
which could be dangerous at noirq-context along with regulator framework.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The same clock is used for all cpus so we must notify the frequency change
for each one in order to update the configuration of all twd clockevents.
change since V1:
* use policy->cpus instead of cpu_online_mask
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Add new module option "set_max_voltage".
One of the lessons learned from Adaptive Powersaver is that voltage values
returned by processor are for worst case scenario. But required voltage
is changing with CPU temperature. And even processors produced in the same
batch can have different minimum voltage necessary for stable work at
specified frequency.
On Elonex Webbook, once system starts, temperature never drops below
48 deg. C. Loading module after systems start allows user to lower CPU
voltage and still have stable system.
Sadly C7 doesn't allow code to set frequency or voltage from outside limits.
If you ask it to set voltage lower then minimum it will ignore you. Thats
why it isn't possible to change minimum voltage for minimum frequency too.
Changing maximum voltage on Elonex Webbook leads to very good results. Looks
like VIA C7 1.6GHz 1084mV can safetly run at 892mV. This means 83% of
orginal value. If same percentage applies to power generated it means 12.5W
in the place of 15W. Not much, but it is better then nothing.
Only C7-M makes it possible.
If voltage is too low by 16mV or more you will experience kernel panic.
If voltage is too low by 32mV or more you will experience system freeze.
Signed-off-by: Rafał Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Call ACPI function to get BIOS limit for CPU frequency.
Fail if processor would like to run at higher frequency.
Allow user to ignore BIOS limit.
eps: Detected VIA Model D C7-M
eps: Current voltage = 1084mV
eps: Current multiplier = 16
eps: Highest voltage = 1084mV
eps: Highest multiplier = 16
eps: Lowest voltage = 844mV
eps: Lowest multiplier = 4
eps: ACPI limit 1.60GHz
Signed-off-by: Rafał Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Some systems are using 1,2Ghz@844mV processors running at 600MHz@796mV.
Try to detect such systems and don't touch anything on it. If CPU doesn't have
P-States in BIOS it should run at maximum frequency.
Allow user to bypass checks by means of two new options.
Don't set frequency to maximum on module unloading to avoid bada boom.
It is also possible that some processors may have incorrect values in min/max
registers caused by error in manufacturing process. Probably it would be BIOS
job to set them to right frequency and P-States tables would have correct
values inside.
Two additional sanity checks for voltage.
Signed-off-by: Rafał Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch enables 'scaling_available_frequencies' attribute
showing list of available frequencies.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
tools, slub: Fix off-by-one buffer corruption after readlink() call
slub: Discard slab page when node partial > minimum partial number
slub: correct comments error for per cpu partial
mm: restrict access to slab files under procfs and sysfs
slub: Code optimization in get_partial_node()
slub: doc: update the slabinfo.c file path
slub: explicitly document position of inserting slab to partial list
slub: update slabinfo tools to report per cpu partial list statistics
slub: per cpu cache for partial pages
slub: return object pointer from get_partial() / new_slab().
slub: pass kmem_cache_cpu pointer to get_partial()
slub: Prepare inuse field in new_slab()
slub: Remove useless statements in __slab_alloc
slub: free slabs without holding locks
slub: use print_hex_dump
slab: use print_hex_dump
* 'for-linus' of git://git.open-osd.org/linux-open-osd: (21 commits)
ore: Enable RAID5 mounts
exofs: Support for RAID5 read-4-write interface.
ore: RAID5 Write
ore: RAID5 read
fs/Makefile: Always inspect exofs/
ore: Make ore_calc_stripe_info EXPORT_SYMBOL
ore/exofs: Change ore_check_io API
ore/exofs: Define new ore_verify_layout
ore: Support for partial component table
ore: Support for short read/writes
exofs: Support for short read/writes
ore: Remove check for ios->kern_buff in _prepare_for_striping to later
ore: cleanup: Embed an ore_striping_info inside ore_io_state
ore: Only IO one group at a time (API change)
ore/exofs: Change the type of the devices array (API change)
ore: Make ore_striping_info and ore_calc_stripe_info public
exofs: Remove unused data_map member from exofs_sb_info
exofs: Rename struct ore_components comps => oc
exofs/super.c: local functions should be static
exofs/ore.c: local functions should be static
...
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64, unistd: Remove bogus __IGNORE_getcpu
x86, mm, trivial: Remove unnecessary get_order() in free_thread_info()
x86, cleanup: Remove unneeded version.h include from arch/x86/
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64: Fix CFI data for interrupt frames
x86-64: Don't apply destructive erratum workaround on unaffected CPUs
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Standardize on CONFIG_SPARSE_IRQ=y
x86, ioapic: Clean up ioapic/apic_id usage
x86, ioapic: Factor out print_IO_APIC() to only print one io apic
x86, ioapic: Print out irte with right ioapic index
x86, ioapic: Split up setup_ioapic_entry()
x86, ioapic: Pass struct irq_attr * to setup_ioapic_irq()
apic, i386/bigsmp: Fix false warnings regarding logical APIC ID mismatches
Mark Einon points out that the Kconfig option for NETDEV_1000 no longer
exists, and the merge of the staging drivers should have removed that
for the et131x driver.
And while checking for it, I noticed that slicoss had the same stale
dependency. Remove that one too.
Reported-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
time, s390: Get rid of compile warning
dw_apb_timer: constify clocksource name
time: Cleanup old CONFIG_GENERIC_TIME references that snuck in
time: Change jiffies_to_clock_t() argument type to unsigned long
alarmtimers: Fix error handling
clocksource: Make watchdog reset lockless
posix-cpu-timers: Cure SMP accounting oddities
s390: Use direct ktime path for s390 clockevent device
clockevents: Add direct ktime programming function
clockevents: Make minimum delay adjustments configurable
nohz: Remove "Switched to NOHz mode" debugging messages
proc: Consider NO_HZ when printing idle and iowait times
nohz: Make idle/iowait counter update conditional
nohz: Fix update_ts_time_stat idle accounting
cputime: Clean up cputime_to_usecs and usecs_to_cputime macros
alarmtimers: Rework RTC device selection using class interface
alarmtimers: Add try_to_cancel functionality
alarmtimers: Add more refined alarm state tracking
alarmtimers: Remove period from alarm structure
alarmtimers: Remove interval cap limit hack
...
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
llist: Add back llist_add_batch() and llist_del_first() prototypes
sched: Don't use tasklist_lock for debug prints
sched: Warn on rt throttling
sched: Unify the ->cpus_allowed mask copy
sched: Wrap scheduler p->cpus_allowed access
sched: Request for idle balance during nohz idle load balance
sched: Use resched IPI to kick off the nohz idle balance
sched: Fix idle_cpu()
llist: Remove cpu_relax() usage in cmpxchg loops
sched: Convert to struct llist
llist: Add llist_next()
irq_work: Use llist in the struct irq_work logic
llist: Return whether list is empty before adding in llist_add()
llist: Move cpu_relax() to after the cmpxchg()
llist: Remove the platform-dependent NMI checks
llist: Make some llist functions inline
sched, tracing: Show PREEMPT_ACTIVE state in trace_sched_switch
sched: Remove redundant test in check_preempt_tick()
sched: Add documentation for bandwidth control
sched: Return unused runtime on group dequeue
...
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (121 commits)
perf symbols: Increase symbol KSYM_NAME_LEN size
perf hists browser: Refuse 'a' hotkey on non symbolic views
perf ui browser: Use libslang to read keys
perf tools: Fix tracing info recording
perf hists browser: Elide DSO column when it is set to just one DSO, ditto for threads
perf hists: Don't consider filtered entries when calculating column widths
perf hists: Don't decay total_period for filtered entries
perf hists browser: Honour symbol_conf.show_{nr_samples,total_period}
perf hists browser: Do not exit on tab key with single event
perf annotate browser: Don't change selection line when returning from callq
perf tools: handle endianness of feature bitmap
perf tools: Add prelink suggestion to dso update message
perf script: Fix unknown feature comment
perf hists browser: Apply the dso and thread filters when merging new batches
perf hists: Move the dso and thread filters from hist_browser
perf ui browser: Honour the xterm colors
perf top tui: Give color hints just on the percentage, like on --stdio
perf ui browser: Make the colors configurable and change the defaults
perf tui: Remove unneeded call to newtCls on startup
perf hists: Don't format the percentage on hist_entry__snprintf
...
Fix up conflicts in arch/x86/kernel/kprobes.c manually.
Ingo's tree did the insane "add volatile to const array", which just
doesn't make sense ("volatile const"?). But we could remove the const
*and* make the array volatile to make doubly sure that gcc doesn't
optimize it away..
Also fix up kernel/trace/ring_buffer.c non-data-conflicts manually: the
reader_lock has been turned into a raw lock by the core locking merge,
and there was a new user of it introduced in this perf core merge. Make
sure that new use also uses the raw accessor functions.
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Add IRQF_RESUME_EARLY and resume such IRQs earlier
genirq: Fix fatfinered fixup really
genirq: percpu: allow interrupt type to be set at enable time
genirq: Add support for per-cpu dev_id interrupts
genirq: Add IRQCHIP_SKIP_SET_WAKE flag
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
rcu: Move propagation of ->completed from rcu_start_gp() to rcu_report_qs_rsp()
rcu: Remove rcu_needs_cpu_flush() to avoid false quiescent states
rcu: Wire up RCU_BOOST_PRIO for rcutree
rcu: Make rcu_torture_boost() exit loops at end of test
rcu: Make rcu_torture_fqs() exit loops at end of test
rcu: Permit rt_mutex_unlock() with irqs disabled
rcu: Avoid having just-onlined CPU resched itself when RCU is idle
rcu: Suppress NMI backtraces when stall ends before dump
rcu: Prohibit grace periods during early boot
rcu: Simplify unboosting checks
rcu: Prevent early boot set_need_resched() from __rcu_pending()
rcu: Dump local stack if cannot dump all CPUs' stacks
rcu: Move __rcu_read_unlock()'s barrier() within if-statement
rcu: Improve rcu_assign_pointer() and RCU_INIT_POINTER() documentation
rcu: Make rcu_assign_pointer() unconditionally insert a memory barrier
rcu: Make rcu_implicit_dynticks_qs() locals be correct size
rcu: Eliminate in_irq() checks in rcu_enter_nohz()
nohz: Remove nohz_cpu_mask
rcu: Document interpretation of RCU-lockdep splats
rcu: Allow rcutorture's stat_interval parameter to be changed at runtime
...
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
rtmutex: Add missing rcu_read_unlock() in debug_rt_mutex_print_deadlock()
lockdep: Comment all warnings
lib: atomic64: Change the type of local lock to raw_spinlock_t
locking, lib/atomic64: Annotate atomic64_lock::lock as raw
locking, x86, iommu: Annotate qi->q_lock as raw
locking, x86, iommu: Annotate irq_2_ir_lock as raw
locking, x86, iommu: Annotate iommu->register_lock as raw
locking, dma, ipu: Annotate bank_lock as raw
locking, ARM: Annotate low level hw locks as raw
locking, drivers/dca: Annotate dca_lock as raw
locking, powerpc: Annotate uic->lock as raw
locking, x86: mce: Annotate cmci_discover_lock as raw
locking, ACPI: Annotate c3_lock as raw
locking, oprofile: Annotate oprofilefs lock as raw
locking, video: Annotate vga console lock as raw
locking, latencytop: Annotate latency_lock as raw
locking, timer_stats: Annotate table_lock as raw
locking, rwsem: Annotate inner lock as raw
locking, semaphores: Annotate inner lock as raw
locking, sched: Annotate thread_group_cputimer as raw
...
Fix up conflicts in kernel/posix-cpu-timers.c manually: making
cputimer->cputime a raw lock conflicted with the ABBA fix in commit
bcd5cff721 ("cputimer: Cure lock inversion").
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, ioapic: Consolidate the explicit EOI code
x86, ioapic: Restore the mask bit correctly in eoi_ioapic_irq()
x86, kdump, ioapic: Reset remote-IRR in clear_IO_APIC
iommu: Rename the DMAR and INTR_REMAP config options
x86, ioapic: Define irq_remap_modify_chip_defaults()
x86, msi, intr-remap: Use the ioapic set affinity routine
iommu: Cleanup ifdefs in detect_intel_iommu()
iommu: No need to set dmar_disabled in check_zero_address()
iommu: Move IOMMU specific code to intel-iommu.c
intr_remap: Call dmar_dev_scope_init() explicitly
x86, x2apic: Enable the bios request for x2apic optout
* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1519 commits)
staging: et131x: Remove redundant check and return statement
staging: et131x: Mainly whitespace changes to appease checkpatch
staging: et131x: Remove last of the forward declarations
staging: et131x: Remove even more forward declarations
staging: et131x: Remove yet more forward declarations
staging: et131x: Remove more forward declarations
staging: et131x: Remove forward declaration of et131x_adapter_setup
staging: et131x: Remove some forward declarations
staging: et131x: Remove unused rx_ring.recv_packet_pool
staging: et131x: Remove call to find pci pm capability
staging: et131x: Remove redundant et131x_reset_recv() call
staging: et131x: Remove unused rx_ring.recv_buffer_pool
Staging: bcm: Fix three initialization errors in InterfaceDld.c
Staging: bcm: Fix coding style issues in InterfaceDld.c
staging:iio:dac: Add AD5360 driver
staging:iio:trigger:bfin-timer: Fix compile error
Staging: vt6655: add some range checks before memcpy()
Staging: vt6655: whitespace fixes to iotcl.c
Staging: vt6656: add some range checks before memcpy()
Staging: vt6656: whitespace cleanups in ioctl.c
...
Fix up conflicts in:
- drivers/{Kconfig,Makefile}, drivers/staging/{Kconfig,Makefile}:
vg driver movement
- drivers/staging/brcm80211/brcmfmac/{dhd_linux.c,mac80211_if.c}:
driver removal vs now stale changes
- drivers/staging/rtl8192e/r8192E_core.c:
driver removal vs now stale changes
- drivers/staging/et131x/et131*:
driver consolidation into one file, tried to do fixups
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (79 commits)
TTY: serial_core: Fix crash if DCD drop during suspend
tty/serial: atmel_serial: bootconsole removed from auto-enumerates
Revert "TTY: call tty_driver_lookup_tty unconditionally"
tty/serial: atmel_serial: add device tree support
tty/serial: atmel_serial: auto-enumerate ports
tty/serial: atmel_serial: whitespace and braces modifications
tty/serial: atmel_serial: change platform_data variable name
tty/serial: RS485 bindings for device tree
TTY: call tty_driver_lookup_tty unconditionally
TTY: pty, release tty in all ptmx_open fail paths
TTY: make tty_add_file non-failing
TTY: drop driver reference in tty_open fail path
8250_pci: Fix kernel panic when pch_uart is disabled
h8300: drivers/serial/Kconfig was moved
parport_pc: release IO region properly if unsupported ITE887x card is found
tty: Support compat_ioctl get/set termios_locked
hvc_console: display printk messages on console.
TTY: snyclinkmp: forever loop in tx_load_dma_buffer()
tty/n_gsm: avoid fifo overflow in gsm_dlci_data_output
tty/n_gsm: fix a bug in gsm_dlci_data_output (adaption = 2 case)
...
Fix up Conflicts in:
- drivers/tty/serial/8250_pci.c
Trivial conflict with removed duplicate device ID
- drivers/tty/serial/atmel_serial.c
Annoying silly conflict between "specify the port num via
platform_data" and other changes to atmel_console_init
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (26 commits)
hwmon: (w83627ehf) Better fix for negative temperature values
hwmon: (w83627ehf) Uninline is_word_sized
hwmon: (lm75) Document why clones are not detected
hwmon: (w83627ehf) Move fan pins check to a separate function
hwmon: (w83627ehf) Skip reading unused voltage registers
hwmon: (lm75) Add support for Analog Devices ADT75
hwmon: (pmbus_core) Simplify sign extensions
hwmon: (pmbus) Add support for Lineage Power DC-DC converters
hwmon: (pmbus/ltc2978) Add support for LTC3880 to LTC2978 driver
hwmon: (pmbus/ltc2978) Explicit driver for LTC2978
hwmon: (pmbus) Add support for TEMP2 peak attributes
hwmon: AD7314 driver (ported from IIO)
hwmon: (pmbus) Add support for Intersil power management chips
hwmon: (pmbus) Always call _pmbus_read_byte in core driver
hwmon: (pmbus) Replace EINVAL return codes with more appropriate errors
hwmon: (pmbus) Provide more documentation
hwmon/f71882fg: Make the decision wether to register fan attr. per fan
hwmon/f71882fg: Add a f71882fg_create_fan_sysfs_files helper function
hwmon/f71882fg: Make all fan/pwm attr tables 2 dimensional
hwmon: (exynos4_tmu) Remove IRQF_DISABLED
...
* git://github.com/rustyrussell/linux:
params: make dashes and underscores in parameter names truly equal
kmod: prevent kmod_loop_msg overflow in __request_module()
* 'for-linus' of git://github.com/ericvh/linux:
9p: fix 9p.txt to advertise msize instead of maxdata
net/9p: Convert net/9p protocol dumps to tracepoints
fs/9p: change an int to unsigned int
fs/9p: Cleanup option parsing in 9p
9p: move dereference after NULL check
fs/9p: inode file operation is properly initialized init_special_inode
fs/9p: Update zero-copy implementation in 9p
This flag is a NOOP and can be removed now.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Bob Liu <lliubbo@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The user may use "foo-bar" for a kernel parameter defined as "foo_bar".
Make sure it works the other way around too.
Apply the equality of dashes and underscores on early_params and __setup
params as well.
The example given in Documentation/kernel-parameters.txt indicates that
this is the intended behaviour.
With the patch the kernel accepts "log-buf-len=1M" as expected.
https://bugzilla.redhat.com/show_bug.cgi?id=744545
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (neatened implementations)
Due to post-increment in condition of kmod_loop_msg in __request_module(),
the system log can be spammed by much more than 5 instances of the 'runaway
loop' message if the number of events triggering it makes the kmod_loop_msg
to overflow.
Fix that by making sure we never increment it past the threshold.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
CC: stable@kernel.org
In 3.0 we changed the way recovery_disabled was handle so that instead
of testing against zero, we test an mddev-> value against a conf->
value.
Two problems:
1/ one place in raid1 was missed and still sets to '1'.
2/ We didn't explicitly set the conf-> value at array creation
time.
It defaulted to '0' just like the mddev value does so they
could appear equal and thus disable recovery.
This did not affect normal 'md' as it calls bind_rdev_to_array
which changes the mddev value. However the dmraid interface
doesn't call this and so doesn't change ->recovery_disabled; so at
array start all recovery is incorrectly disabled.
So initialise the 'conf' value to one less that the mddev value, so
the will only be the same when explicitly set that way.
Reported-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Remove i2c_board_info for driver that doesn't exist anymore.
Delete irq_flags for drivers that don't use them anymore.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There is already an entry in the spi device table for the codec, but the
modalias was wrong. Also the config symbol name for the codec is wrong,
so this is fixed as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This header was being rewritten while the asm-generic kbuild support
was in flight, so it missed out on the update. Punt the stub and use
the kbuild now that everything has settled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
SND_BF5XX_SOC is for machine drivers while SND_SOC is for codec drivers.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The ASoC codec name is "ad1836" and not "ad183x" as the change to rename
things ultimately did not get merged.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
__kfree_rcu() in rcupdate.h bugs when parameter offset is not a constant
at compile time. Since we build the kgdb_test module with -O0 and it
includes this header file, we hit the bug. So drop the -O0 and mark the
one func we need for the test as noinline (so we can set a breakpoint on
it and have it be hit).
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure our smp_send_reschedule() implementation matches the
scheduler_ipi() callback so that it can kick the idle cpu.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
IRQF_SHARED is not part of the IORESOURCE_IRQ bits. It's expressed by
IORESOURCE_IRQ_SHAREABLE.
IORESOURCE_IRQ_HIGHEDGE and IRQF_TRIGGER_HIGH are contradicting
values, an interrupt can hardly be configured for both level and edge
at the same time. This was introduced in commit 45138439(Blackfin
arch: flash memory map and dm9000 resources updating) of course
without any hint in the changelog what the heck this is supposed to
do.
Acked-by: Javier Herrero <jherrero@hvsistemas.es>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that common code supports SMP systems, switch our SMP atomic logic
over to it to avoid code duplication.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This bug was introduced in 415e72d034
which was in 2.6.36.
There is a small window of time between when a device fails and when
it is removed from the array. During this time we might still read
from it, but we won't write to it - so it is possible that we could
read stale data.
We didn't need the test of 'Faulty' before because the test on
In_sync is sufficient. Since we started allowing reads from the early
part of non-In_sync devices we need a test on Faulty too.
This is suitable for any kernel from 2.6.36 onwards, though the patch
might need a bit of tweaking in 3.0 and earlier.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
The caif code will register its own pernet_operations, and then register
a netdevice_notifier. Each time the netdevice_notifier is triggered,
it'll do some stuff... including a lookup of its own pernet stuff with
net_generic().
If the net_generic() call ever returns NULL, the caif code will BUG().
That doesn't seem *so* unreasonable, I suppose — it does seem like it
should never happen.
However, it *does* happen. When we clone a network namespace,
setup_net() runs through all the pernet_operations one at a time. It
gets to loopback before it gets to caif. And loopback_net_init()
registers a netdevice... while caif hasn't been initialised. So the caif
netdevice notifier triggers, and immediately goes BUG().
We could imagine a complex and overengineered solution to this generic
class of problems, but this patch takes the simple approach. It just
makes caif_device_notify() *not* go looking for its pernet data
structures if the device it's being notified about isn't a caif device
in the first place.
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
