Nobody seems to want to own I2O patches so sending this one directly.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Powerpc 44x uses 36 bit real address while the real address defined in
MPT Fusion driver is of type 32 bit. This causes ioremap to fail and
driver fails to initialize. This fix changes the data types
representing the real address from unsigned long 32-bit types to
resource_size_t which is 64-bit. The driver has been tested, the disks
get discovered correctly and can do IO.
[jejb: added printk fix for resource_size_t object]
Signed-off-by: Pravin Bathija <pbathija@amcc.com>
Acked-by: "Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Errata:
Certain conditions on the scsi bus may casue the 53C1030 to incorrectly signal
a SCSI_DATA_UNDERRUN to the host.
Workaround 1:
For an Errata on LSI53C1030 When the length of request data
and transfer data are different with result of command (READ or VERIFY),
DID_SOFT_ERROR is set.
Workaround 2:
For potential trouble on LSI53C1030. It is checked whether the length of
request data is equal to the length of transfer and residual.
MEDIUM_ERROR is set by incorrect data.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (209 commits)
[SCSI] fix oops during scsi scanning
[SCSI] libsrp: fix memory leak in srp_ring_free()
[SCSI] libiscsi, bnx2i: make bound ep check common
[SCSI] libiscsi: add completion function for drivers that do not need pdu processing
[SCSI] scsi_dh_rdac: changes for rdac debug logging
[SCSI] scsi_dh_rdac: changes to collect the rdac debug information during the initialization
[SCSI] scsi_dh_rdac: move the init code from rdac_activate to rdac_bus_attach
[SCSI] sg: fix oops in the error path in sg_build_indirect()
[SCSI] mptsas : Bump version to 3.04.12
[SCSI] mptsas : FW event thread and scsi mid layer deadlock in SYNCHRONIZE CACHE command
[SCSI] mptsas : Send DID_NO_CONNECT for pending IOs of removed device
[SCSI] mptsas : PAE Kernel more than 4 GB kernel panic
[SCSI] mptsas : NULL pointer on big endian systems causing Expander not to tear off
[SCSI] mptsas : Sanity check for phyinfo is added
[SCSI] scsi_dh_rdac: Add support for Sun StorageTek ST2500, ST2510 and ST2530
[SCSI] pmcraid: PMC-Sierra MaxRAID driver to support 6Gb/s SAS RAID controller
[SCSI] qla2xxx: Update version number to 8.03.01-k6.
[SCSI] qla2xxx: Properly delete rports attached to a vport.
[SCSI] qla2xxx: Correct various NPIV issues.
[SCSI] qla2xxx: Correct qla2x00_eh_wait_on_command() to wait correctly.
...
Normally In HBA reset path MPT driver will flush existing work in current work
queue (mpt/0) . This is just a dummy activity for MPT driver point of
view, since HBA reset will turn off Work queue events.
It means we will simply returns from work queue without doing anything.
But for the case where Work is already done (half the way), we have to have
that work to be done.
Considering above condition we stuck forever since Deadlock in scsi midlayer
and MPT driver. sd_sync_cache() will wait forever since HBA is not in
Running state, and it will never come into Running state since
sd_sync_cache() is called from HBA reset context.
Now new code will not wait for half cooked work to be finished
before returning from HBA reset.
Once we are out of HBA reset, EH thread will change host state to running from
recovery and work waiting for running state of HBA will be finished.
New code is turning ON firmware event from another special work called
Rescan toplogy.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver is modified to return DID_NO_CONNECT for all pending I/O
requests for bus type SAS, if it founds the target is removed at
the firmware level.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch is solving problem for PAE kernel DMA operation.
On PAE system dma_addr and unsigned long will have different
values.
Now dma_addr is not type casted using unsigned long.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
On Big endian system kernel will crash due to address translation
is not handle properly.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Check for phyinfo->phy before calling sas_port_delete_phy.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Do not set max_id value received from FW. Once SAS transport layer is
introduced max_id value is missleading to SCSI mid layer. Use max_id to
infinite value.
logic of can queue of scsi host is changed.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two typos in mptsas_not_responding_devices. It was mutex_lock instead
of unlock.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: "Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We're about to make DMA_nnBIT_MASK() emit `deprecated' warnings. Convert the
remaining stragglers which are visible to the x86_64 build.
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsil.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Yi Zou <yi.zou@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/message/fusion/mptsas.c
fixed up conflict between req->data_len accessors and mptsas driver updates.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Several of the doc book in the previous patches had incorrect multi-line short
function descriptors. Fixed it all to be the correct single line descriptor.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware is able to handle Broadcast primitives, but upstream driver does not
have support for broadcast primitive handling. Now this patch is mainly to
support broadcast primitives.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
FW will report Queue full event to Driver and driver will handle this queue
full event to SCSI Mid layer.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1. Handle integrated Raid device(Add/Delete) and error condition and check
related to Raid device. is_logical_volume will represent logical volume
device.
2. Raid device dual port support is added. Main functions to support this
feature are mpt_raid_phys_disk_get_num_paths and mpt_raid_phys_disk_pg1.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Resending patch considering Grants G's code review.
Main goal to submit this patch is code cleaup.
1. Better driver debug prints and code indentation.
2. fault_reset_work_lock is not used anywhere. driver is using taskmgmt_lock
instead of fault_reset_work_lock.
3. setting pci_set_drvdata properly.
4. Ingore config request when IOC is in reset state.( ioc_reset_in_progress
is set).
5. Init/clear managment frame proprely.(INITIALIZE_MGMT_STATUS and
CLEAR_MGMT_STATUS)
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1.) SAS topology Rescan is added. If Firmware is doing Reset and we get
Device add interrupt from Firmware, we will not receive it as part of Reset
is going ON. After Reset we will do special Rescan of SAS topology.
2.) Driver version changed from 3.04.08 to 3.04.09.
Added proper lock/unlock in mptsas_not_responding_devices() as per James'
comment.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SAS topology scan is restructured. HBA firmware is generating more
events. Expander Events are added, Link status events are also added with
respect to SAS topology scan optimization.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Now Firmware events are handled by firmware event queue.
Previously it was handled in interrupt context/WorkQueue of Linux.
Firmware Event handling is restructured and optimized.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1) rewrite of ioctl_cmds internal generated function that issue commands to
firmware, porting them to be single threaded using the generic MPT_MGMT
struct. All wait Queues are replace by completion Queue.
2) added seperate callback handler for ioctl task managment
(mptctl_taskmgmt_reply), to handle command that timeout
3) rewrite mptctl_bus_reset
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1.) Added taskmgmt_quiesce_io flag in IOC and removed resetPending from
_MPT_SCSI_HOST struct.
2.) Reset from Scsi mid layer and internal Reset are seperate context.
Adding DeviceResetCtx for internal Device reset frame.
mptsas_taskmgmt_complete is optimized as part of implementation.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1.) rewrite taskmanagement request and completion routines, making them
single threaded and using the generic MPT_MGMT struct, deleting
mptscsih_TMHandler, replacing with single request TM handler
mptscsih_IssueTaskMgmt, and killing the watchdog timer functions.
2.) cleanup ioc_reset callback handlers, introducing wrappers for
synchronizing error recovery (mpt_set_taskmgmt_in_progress_flag,
mpt_clear_taskmgmt_in_progress_flag), as the fusion firmware only handles
one task management request at a time
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rewrite of all internal generated functions that issue commands to firmware,
porting them to be single threaded using the generic MPT_MGMT
struct. Implemented using completion Queue.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1) Previously we had mutliple #defines to use same values.
Now those #defines are optimized.
MPT_IOCTL_STATUS_* is removed and MPT_MGMT_STATUS_* are new
#defines.
2.) config path is optimized.
Instead of wait Queue and timer, using completion Q.
3.) mpt_timer_expired is not used.
[jejb: elide patch to eliminate mpt_timer_expired]
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SendEventNotification was handled through FIFO, now it is using doorbell to
communicate with hardware. Added Sleep Flag as an extra argument to support
Can-Sleep feature. Resending patch including compilation error fix reviewed
by Grant Grundler.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sas_discovery_quiesce_io flag is used to control IO start/resume functionality.
IO will be stoped while doing discovery of topology. Once discovery is completed
It will resume IO. Resending patch including James review.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The reason for this change is there is a data corruption when four different
physical memory regions in the 36GB to 37GB region are
accessed. This is only affecting 1078.
The solution is we need to use different addressing when filling in
the scatter gather table for the effected memory regions. So instead
of snooping on all four different memory holes, we treat any physical
addresses in the 36GB address with the same algorithm.
The fix is explained below
1) Ensure that the message frames are NOT located in the trouble
region. There is no remapping available for message frames, they must
be allocated outside the problem region.
2) Ensure that Sense buffers are NOT in the trouble region. There is
no remapping available.
3) Walk through the SGE entries and if any are inside the trouble region
then they need to be remapped as discussed below.
1) Set the Local Address bit in the SGE Flags field.
MPI_SGE_FLAGS_LOCAL_ADDRESS
2) Ensure we are using 64-bit SGEs
3) Set MSb (Bit 63) of the 64-bit address, this will indicate buffer
location is Host Memory.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
In commit c3a4d78c58, while introducing
rq->resid_len, the default value of residue count was changed from
full count to zero. The conversion was done under the assumption that
when a request fails residue count wasn't defined. However, Boaz and
James pointed out that this wasn't true and the residue count should
be preserved for failed requests too.
This patchset restores the original behavior by setting rq->resid_len
to blk_rq_bytes(rq) on request start and restoring explicit clearing
in affected drivers. While at it, take advantage of the fact that
rq->resid_len is set to full count where applicable.
* ide-cd: rq->resid_len cleared on pc success
* mptsas: req->resid_len cleared on success
* sas_expander: rsp/req->resid_len cleared on success
* mpt2sas_transport: req->resid_len cleared on success
* ide-cd, ide-tape, mptsas, sas_host_smp, mpt2sas_transport, ub: take
advantage of initial full count to simplify code
Boaz Harrosh spotted bug in resid_len initialization. Fixed as
suggested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
plat-omap/mailbox, floppy, viocd, mspro_block, i2o_block and
mmc/card/queue are already pretty close to dequeueing model and can be
converted with simple changes. Convert them.
While at it,
* xen-blkfront: !fs check moved downwards to share dequeue call with
normal path.
* mspro_block: __blk_end_request(..., blk_rq_cur_byte()) converted to
__blk_end_request_cur()
* mmc/card/queue: loop of __blk_end_request() converted to
__blk_end_request_all()
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With the previous changes, the followings are now guaranteed for all
requests in any valid state.
* blk_rq_sectors() == blk_rq_bytes() >> 9
* blk_rq_cur_sectors() == blk_rq_cur_bytes() >> 9
Clean up accessor usages. Notable changes are
* nbd,i2o_block: end_all used instead of explicit byte count
* scsi_lib: unnecessary conditional on request type removed
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent unification of fields, it's now guaranteed that
rq->data_len always equals blk_rq_bytes(). Convert all non-IDE direct
users to accessors. IDE will be converted in a separate patch.
Boaz: spotted incorrect data_len/resid_len conversion in osd.
[ Impact: convert direct rq->data_len usages to blk_rq_bytes() ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement accessors - blk_rq_pos(), blk_rq_sectors() and
blk_rq_cur_sectors() which return rq->hard_sector, rq->hard_nr_sectors
and rq->hard_cur_sectors respectively and convert direct references of
the said fields to the accessors.
This is in preparation of request data length handling cleanup.
Geert : suggested adding const to struct request * parameter to accessors
Sergei : spotted error in patch description
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Ackec-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion. This duality creates some
headaches.
First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing. It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count. This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.
Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred. The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all. This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.
This patch adds rq->resid_len which is used only for residual count.
While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.
Boaz : spotted missing conversion in osd
Sergei : spotted too early conversion to blk_rq_bytes() in ide-tape
[ Impact: cleanup residual count handling, report 0 resid by default ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
end_request() has been kept around for backward compatibility;
however, it's about time for it to go away.
* There aren't too many users left.
* Its use of @updtodate is pretty confusing.
* In some cases, newer code ends up using mixture of end_request() and
[__]blk_end_request[_all](), which is way too confusing.
So, add [__]blk_end_request_cur() and replace end_request() with it.
Most conversions are straightforward. Noteworthy ones are...
* paride/pcd: next_request() updated to take 0/-errno instead of 1/0.
* paride/pf: pf_end_request() and next_request() updated to take
0/-errno instead of 1/0.
* xd: xd_readwrite() updated to return 0/-errno instead of 1/0.
* mtd/mtd_blkdevs: blktrans_discard_request() updated to return
0/-errno instead of 1/0. Unnecessary local variable res
initialization removed from mtd_blktrans_thread().
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Joerg Dorchain <joerg@dorchain.net>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Laurent Vivier <Laurent@lvivier.info>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: unsik Kim <donari75@gmail.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.
We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.
But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.
->read_proc/->write_proc were just fixed to not require ->owner for
protection.
rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.
Removing ->owner will also make PDE smaller.
So, let's nuke it.
Kudos to Jeff Layton for reminding about this, let's say, oversight.
http://bugzilla.kernel.org/show_bug.cgi?id=12454
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Impact: fix bug
the third param in module_param(,,) is perm instead of default value.
we still need to assign default at first. Also, the default is now
zero not one, so fix the parameter text to reflect that.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support for MSI enable/disable for different buses FC,SPI,SAS
instead of having single MSI enable/disable feature.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This Patch is submitted to increment the MPI headers used by LSI MPT
fusion drivers to the latest version 01.05.19. Year is changed in
CopyRight.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (45 commits)
[SCSI] qla2xxx: Update version number to 8.03.00-k1.
[SCSI] qla2xxx: Add ISP81XX support.
[SCSI] qla2xxx: Use proper request/response queues with MQ instantiations.
[SCSI] qla2xxx: Correct MQ-chain information retrieval during a firmware dump.
[SCSI] qla2xxx: Collapse EFT/FCE copy procedures during a firmware dump.
[SCSI] qla2xxx: Don't pollute kernel logs with ZIO/RIO status messages.
[SCSI] qla2xxx: Don't fallback to interrupt-polling during re-initialization with MSI-X enabled.
[SCSI] qla2xxx: Remove support for reading/writing HW-event-log.
[SCSI] cxgb3i: add missing include
[SCSI] scsi_lib: fix DID_RESET status problems
[SCSI] fc transport: restore missing dev_loss_tmo callback to LLDD
[SCSI] aha152x_cs: Fix regression that keeps driver from using shared interrupts
[SCSI] sd: Correctly handle 6-byte commands with DIX
[SCSI] sd: DIF: Fix tagging on platforms with signed char
[SCSI] sd: DIF: Show app tag on error
[SCSI] Fix error handling for DIF/DIX
[SCSI] scsi_lib: don't decrement busy counters when inserting commands
[SCSI] libsas: fix test for negative unsigned and typos
[SCSI] a2091, gvp11: kill warn_unused_result warnings
[SCSI] fusion: Move a dereference below a NULL test
...
Fixed up trivial conflict due to moving the async part of sd_probe
around in the async probes vs using dev_set_name() in naming.
Convert to net_device_ops and internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
Remove excess kernel-doc function parameter notation from i2o/.
Warning(drivers/message/i2o/iop.c:64): Excess function parameter 'msg' description in 'i2o_msg_get_wait'
Warning(drivers/message/i2o/device.c:62): Excess function parameter 'drv' description in 'i2o_device_claim'
Warning(drivers/message/i2o/device.c:95): Excess function parameter 'drv' description in 'i2o_device_claim_release'
Warning(drivers/message/i2o/driver.c:186): Excess function parameter 'msg' description in 'i2o_driver_dispatch'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the NULL test is necessary, then the dereference should be moved below
the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/).
// <smpl>
@disable is_null@
identifier f;
expression E;
identifier fld;
statement S;
@@
+ if (E == NULL) S
f(...,E->fld,...);
- if (E == NULL) S
@@
identifier f;
expression E;
identifier fld;
statement S;
@@
+ if (!E) S
f(...,E->fld,...);
- if (!E) S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: "Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ARRAY_SIZE is more concise to use when the size of an array is divided by
the size of its type or the size of its first element.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: "Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove excess kernel-doc function parameter notation:
Warning(drivers/message/fusion/mptbase.c:964): Excess function parameter or struct member 'handle' description in 'mpt_free_msg_frame'
Warning(drivers/message/fusion/mptbase.c:5434): Excess function parameter or struct member 'portnum' description in 'mpt_findImVolumes'
Warning(drivers/message/fusion/mptbase.c:6949): Excess function parameter or struct member 'mr' description in 'mpt_spi_log_info'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Eric.Moore@lsi.com
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mpt fusion: clear list of outstanding commands on host reset
[SCSI] scsi_lib: only call scsi_unprep_request() under queue lock
[SCSI] ibmvstgt: move crq_queue_create to the end of initialization
[SCSI] libiscsi REGRESSION: fix passthrough support with older iscsi tools
[SCSI] aacraid: disable Dell Percraid quirk on Adaptec 2200S and 2120S
A bug in the fusion driver was exposed by the switch to block timeout.
Basically, drivers are supposed to terminate commands once error
handling begins on them. The fusion apparently wasn't doing this.
Under the old timeout regime, completions on terminated commands would
by and large get ignored because of the way command timeouts used to
work. The new block timers are very intolerant to this, though,
becuase the request gets cleaned and freed.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=12195
Reported-by: Alex Shi <alex.shi@intel.com>
Tested-by: Ming Lin <ming.m.lin@intel.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
no argument named @msg in i2o_msg_get_wait(), remove it.
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix incorrect use of loose in i2o_block.c
It should be 'lose', not 'loose'.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This triggers false bug reports as it does a bogus kmalloc with locks held
but is never really compiled into the kernel.
Closes#8329
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixup i2o kernel-doc warnings:
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:579): No description found for parameter 'bdev'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:579): No description found for parameter 'mode'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:608): No description found for parameter 'disk'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:608): No description found for parameter 'mode'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:657): No description found for parameter 'bdev'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:657): No description found for parameter 'mode'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (21 commits)
[SCSI] sd: fix computation of the full size of the device
[SCSI] lib: string_get_size(): don't hang on zero; no decimals on exact
[SCSI] sun3x_esp: Convert && to ||
[SCSI] sd: remove command-size switching code
[SCSI] 3w-9xxx: remove unnecessary local_irq_save/restore for scsi sg copy API
[SCSI] 3w-xxxx: remove unnecessary local_irq_save/restore for scsi sg copy API
[SCSI] fix netlink kernel-doc
[SCSI] sd: Fix handling of NO_SENSE check condition
[SCSI] export busy state via q->lld_busy_fn()
[SCSI] refactor sdev/starget/shost busy checking
[SCSI] mptfusion: Increase scsi-timeouts, similariy to the LSI 4.x driver.
[SCSI] aic7xxx: Take the LED out of diagnostic mode on PM resume
[SCSI] aic79xx: user visible misuse wrong SI units (not disk size!)
[SCSI] ipr: use memory_read_from_buffer()
[SCSI] aic79xx: fix shadowed variables
[SCSI] aic79xx: fix shadowed variables, add statics
[SCSI] aic7xxx: update *_shipped files
[SCSI] aic7xxx: update .reg files
[SCSI] aic7xxx: introduce "dont_generate_debug_code" keyword in aicasm parser
[SCSI] scsi_dh: Initialize path state to be passive when path is not owned
...
Make SPI timeout 10s the same as SAS
Signed-off-by: Bernd Schubert <bs@q-leap.de>
Acked-by: "Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The I2O ioctls assume 32bits. In itself that is fine as they are old
cards and nobody uses 64bit. However on LKML it was noted this
assumption is also made for allocated memory and is unsafe on 64bit
systems.
Fixing this is a mess. It turns out there is tons of crap buried in a
header file that does racy 32/64bit filtering on the masks.
So we:
- Verify all callers of the racy code can sleep (i2o_dma_[re]alloc)
- Move the code into a new i2o/memory.c file
- Remove the gfp_mask argument so nobody can try and misuse the function
- Wrap a mutex around the problem area (a single mutex is easy to do and
none of this is performance relevant)
- Switch the remaining problem kmalloc holdout to use i2o_dma_alloc
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (59 commits)
[SCSI] replace __FUNCTION__ with __func__
[SCSI] extend the last_sector_bug flag to cover more sectors
[SCSI] qla2xxx: Update version number to 8.02.01-k6.
[SCSI] qla2xxx: Additional NPIV corrections.
[SCSI] qla2xxx: suppress uninitialized-var warning
[SCSI] qla2xxx: use memory_read_from_buffer()
[SCSI] qla2xxx: Issue proper ISP callbacks during stop-firmware.
[SCSI] ch: fix ch_remove oops
[SCSI] 3w-9xxx: add MSI support and misc fixes
[SCSI] scsi_lib: use blk_rq_tagged in scsi_request_fn
[SCSI] ibmvfc: Update driver version to 1.0.1
[SCSI] ibmvfc: Add ADISC support
[SCSI] ibmvfc: Miscellaneous fixes
[SCSI] ibmvfc: Fix hang on module removal
[SCSI] ibmvfc: Target refcounting fixes
[SCSI] ibmvfc: Reduce unnecessary log noise
[SCSI] sym53c8xx: free luntbl in sym_hcb_free
[SCSI] scsi_scan.c: Release mutex in error handling code
[SCSI] scsi_eh_prep_cmnd should save scmd->underflow
[SCSI] sd: Support for SCSI disk (SBC) Data Integrity Field
...
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Compile warning:
ignoring return value of `sysfs_create_link', declared with attribute warn_unused_result.
If sysfs_create_link failed, take care of the return value and do some
error handle after the failure.
Since sysfs_remove_link() will check whether a link exists, when removing the
link in error path, we don't need to care whether a link was created.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kobjects do not have a limit in name size since a while, so stop
pretending that they do.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (102 commits)
[SCSI] scsi_dh: fix kconfig related build errors
[SCSI] sym53c8xx: Fix bogus sym_que_entry re-implementation of container_of
[SCSI] scsi_cmnd.h: remove double inclusion of linux/blkdev.h
[SCSI] make struct scsi_{host,target}_type static
[SCSI] fix locking in host use of blk_plug_device()
[SCSI] zfcp: Cleanup external header file
[SCSI] zfcp: Cleanup code in zfcp_erp.c
[SCSI] zfcp: zfcp_fsf cleanup.
[SCSI] zfcp: consolidate sysfs things into one file.
[SCSI] zfcp: Cleanup of code in zfcp_aux.c
[SCSI] zfcp: Cleanup of code in zfcp_scsi.c
[SCSI] zfcp: Move status accessors from zfcp to SCSI include file.
[SCSI] zfcp: Small QDIO cleanups
[SCSI] zfcp: Adapter reopen for large number of unsolicited status
[SCSI] zfcp: Fix error checking for ELS ADISC requests
[SCSI] zfcp: wait until adapter is finished with ERP during auto-port
[SCSI] ibmvfc: IBM Power Virtual Fibre Channel Adapter Client Driver
[SCSI] sg: Add target reset support
[SCSI] lib: Add support for the T10 (SCSI) Data Integrity Field CRC
[SCSI] sd: Move scsi_disk() accessor function to sd.h
...
When the firmware is in Fault state it will be identifed only when the next time
the driver access the IOC state.
This patch includes a polling function in the driver which will be executed in
regular interval to check the status of the firmware and if it is in Fault
state, then the firmware will be reset by the driver.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The initial period is set to 0xFF
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's a fault on the FC controllers that makes them not respond
correctly to MSI. The SPI controllers are fine, but are likely to be
onboard on older motherboards which don't handle MSI correctly, so
default both these cases to disabled. Enable by setting the module
parameter mpt_msi_enable=1.
For the SAS case, enable MSI by default, but it can be disabled by
setting the module parameter mpt_msi_enable=0.
Cc: "Prakash, Sathya" <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The problem here is that if the ioc faults too early in the bring up
sequence (as it usually does for an irq routing problem), ioc_reset gets
called before the scsi host is even allocated. This causes an oops when
it later schedules a renegotiation. Fix this by checking ioc->sh before
trying to renegotiate.
Cc: "Moore, Eric" <Eric.Moore@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Updating copyright statement to include the year 2008
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Updating driver version to 3.04.07 from 3.04.06
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes the needlessly global struct mpt_proc_root_dir static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: "Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following a hard reset of a SAS raid, one of the raid targets is occasionally
missing. I tracked this down to a pretty obscure little bug.
The LSI fusion drivers for SAS and Fibre Channel both use their respective
transport layers. Those transport layers increment the target number
assigned to new targets.
The routine __scsi_scan_target uses the "this_id" element of the Scsi_Host
structure to avoid scanning the scsi host adapter. Both fusion drivers set
"this_id" from a value returned in a firmware PortFacts response. For my
particular test case (SAS) the firmware id assigned to the initiator was
173. After enough raid resets to cause the raid targets to go and come a
sufficient number of times, the id assigned by the transport to a raid
target would match the id assigned by the host adapter to the "this_id"
field, resulting in that target not being scanned.
Fix by not assigning this_id and not checking it in slave_configure.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some drivers have duplicated unlikely() macros. IS_ERR() already has
unlikely() in itself.
This patch cleans up such pointless code.
Signed-off-by: Hirofumi Nakagawa <hnakagawa@miraclelinux.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a problem with the combination of the upstream power
management fixes and the enabling of MSI by default in that the
suspend path still uses the global variable. Convert it to check
ioc->msi_enable.
Cc: "Moore, Eric" <Eric.Moore@lsi.com>
Cc: "Prakash, Sathya" <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
While performing hardware raid reset testing via the raid's client, I
noticed that sometimes, following the reset, that there would be more
raid targets in the lsscsi output than there actually were raid
targets. I tracked this down to the following issue.
Fusion cannot always find the mptsas_portinfo structure for the hba
because it uses the handle stored in ioc->handle to locate it. The
problem is that the firmware can change the handle associated with the
hba when h/w raid is reset (via the raid client). When this happens,
the driver will allocate another mptsas_portinfo structure and link it
into the chain of said structures. This ultimately causes confusion
within the driver resulting in targets not being removed when they
should be.
Eric Moore pointed out that the hba's portinfo structure is always the
first structure on the sas_topology list. This patch modifies
mptsas.c to access the hba's portinfo structure by taking the first
structure on said list.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
the semaphore inactive_list_mutex is used as a mutex, convert it to
the mutex API
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch modifies the driver to enable MSI by default for all SAS chips.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The system power state changes like hibernation and standby are not happening
properly with 106XE controllers, this patch modifies the driver to free
resources and allocate resources in power management entry points
[jejb: compile fixes for upstream]
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Don't oops if NumPhys==0, instead return -ENODEV.
This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=9909
Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix docbook problems in fusion source files.
These cause the generated docbook to be incorrect.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ioc->name is used in the printk's after ioc has been freed. Free
after prinks to fix this.
This patch fixes two use-after-free's introduced by
commit e78d5b8f1e and spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Verified all the arches necessary select the CONFIG_64BIT symbol. This
also kills the warning (since it was using the 32-bit case) on parisc64
and mips64.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch modifies the I/O resource allocation behavior of FUSION
driver. The current version of driver allocates the I/O resources
even if they are not required and this creates trouble in low resource
environments. This driver now uses
pci_enable_device_mem/pci_enable_device functions to differentiate the
resource allocations.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch sets the IOC pointer in drvrdata of pcidev before adding
the IOC into the list of IOCs. Without this patch the driver oops when
the mptsas and mptctl modules are loaded in parallel.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch converts i2o_block to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
As a result, the interface of internal function, i2o_block_end_request(),
is changed.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This replaces sizeof sense_buffer with SCSI_SENSE_BUFFERSIZE in
several LLDs. It's a preparation for the future changes to remove
sense_buffer array in scsi_cmnd structure.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes the module unload problem in flash less 1030
controller environment where firmware download boot functionality is
invoked. The problem is due to the firmware download is being done in
the reverse order, which this patch solves by insureing the download
occurs to the last controller being reset.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes mptsas_smp_handler to update both din_resid or
dout_resid on success. bsg can report back the residual.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
drivers/message/i2o/exec-osm.c:539: warning: `i2o_exec_lct_notify' defined but not used
comes when CONFIG_I2O_LCT_NOTIFY_ON_CHANGES=n, because its only callsite
is #ifdef'ed as such. So let's #ifdef the function definition also. Also
move the definition to before the callsite, to get rid of forward prototype.
[akpm@linux-foundation.org: fix warnings]
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix kernel-api docbook warnings.
Warning(linux-2.6.23-git8//drivers/message/fusion/mptscsih.c:2618): No description found for parameter 'sc'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/message/fusion/mptctl.c: In function ‘mptctl_mpt_command’:
drivers/message/fusion/mptctl.c:1764: warning: ‘bufIn.len’ may be used uninitialized in this function
drivers/message/fusion/mptctl.c:1765: warning: ‘bufOut.len’ may be used uninitialized in this function
come because gcc gets confused by some "goto" statements in above
function. The warnings have been verified to be bogus, however, the
function does initialize these later (after the offending goto's) in
the function anyway. So let's move those initializations to top of
function, thereby also shutting up these warnings.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
NB = number of blocks. This represents the number of blocks to
transfer. The block size is based on the message frame size provided
in the ioc_facts. A value of zero indicates the entire message frame
should be copied. This is two bit value. So by setting this to
non-zero vaule, you increase performance by reducing amount of data
needing to be dma'd. The value that is stored in ioc->ReqeustNB is
sometimes a non-zero vaule, which creates a bug in mptlan, where not
the entire message frame is getting transfer to firware, resulting in
corruption. This fix sets the default to zero, thus entire message
frame is copied.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleaning up prints that use the xxx_printk API, in that the fusion
preamble "mptbase: iocX" follows the info provided by the print API.
The way its currently coded, the [H:C:T] print in sdev_printk will be
inbetween "mptbase" and "iocX", instead of before.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ScsiLookup is an array of pending scmd pointers that the scsi lld
maintains. This array is touched from queuecommand, eh threads, and
interrupt context. This array should put under locks, hence this patch
to synchronize its access. I've added some nice little function
wrappers for this, and moved the ScsiLookup array over to MPT_ADAPTER
struct.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
List below is output from C=2 sparse compilation, which are fixed with
this patch.
1) mptspi: pg0 is defined in x86 version of include/asm/pgtable.h
2) mptsas: context imbalance in 'mptsas_probe' different lock contexts
for basic block
3) mptbase: from mpt_attach - cast adds address space to expression
4) mptbase: from mpt_do_upload - request[] is bad constant expression
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver is currently typecasting to obtain the shost hostdata. The
driver is updated to use the shost_priv macro.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding 949X, 949E, and 1078 to Kconfig. Adding "depends on FUSION"
required in the FUSION_LOGGING section, and fixing a spelling error.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some other vender has concerns over this copyright, and Dell has
approved removing it.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleaning up code by accesing the ioc pointer directly instead of via hd->ioc. In the future, most data members of struct MPT_SCSI_HOST will be either deleted or moved to struct MPT_ADAPTER.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
common naming of vdevice through out driver
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
cleaning up some white space that was introduce in a recent "cb_idx int to u8" patch.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Standardize all prints using common MYIOC_s_XXX_FMT macro defined in mptbase.h. Currently the driver uses several different methods to display info, where in some cases the "controller name" generating the printk is not provided.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
alloc_fcdev() calls alloc_netdev() which uses kzalloc to alloc all the
memory together with dev->priv region hence no zeroing of structs inside
struct mpt_lan_priv needed.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Acked-by: "Moore, Eric Dean" <Eric.Moore@lsil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Coverity checker spotted two potential memory leaks in
drivers/message/fusion/mptbase.c::mpt_attach().
There are two returns that may leak the storage allocated for 'ioc'
(sizeof(MPT_ADAPTER) bytes).
A simple fix would be to simply add two kfree() calls before the return
statements, but a better fix (that this patch implements) is to reorder the
code so that if we hit the first return condition we don't have to do the
allocation at all and then just add a kfree() call for the second case.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: "Moore, Eric Dean" <Eric.Moore@lsil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Acked-by: "Moore, Eric Dean" <Eric.Moore@lsil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Recently LSI Logic Corp was renamed as LSI Corp, so whereever there is
a reference of LSI Logic, it is changed to LSI in mpt fusion driver
code.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When there is state change in FC links, a message is displayed with
old and new link speed.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The data structure definitions from mptsas.c are moved to a new header
file mptsas.h
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The call back index requires only u8 but in lot of places it is
referred as int, now everywhere the call back index variables are
declared as u8 with uniform name cb_idx
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Added support for sending the task management requests through High priority
request FIFO instead of Doorbell writes when firmware support High priority
FIFO.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Per request from Matthew Wilcox - using PCI_VENDOR_ATTO.
Add support for ATTO UL4D, they are rebranded 53C1030.
The changes are
1. Adding a new PCI vendor ID in pci table
2. The spi_port_page_2 is in different format than that of LSI generic
spi_port_page_2 and hence mapping code is added.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/message/i2o/i2o_block.c: In function 'i2o_block_transfer':
drivers/message/i2o/i2o_block.c:837: warning: integer overflow in expression
msg->u.head[1] = cpu_to_le32(I2O_CMD_PRIVATE << 24 | HOST_TID << 12 | tid);
and I2O_CMD_PRIVATE is defined as 0xFF. This gets "0xFF0100 | tid" and fits
into 32-bit unsigned but not into 32-bit signed integer properly. Target
value is defined as u32 so the claculation does not fit during computation.
Change local variable tid to u32 so the whole expression is of u32 type and
fits well into u32 result.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Cc: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for SAS Management Protocol (SMP) passthrough
support via bsg.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Wire up the mpt_debug_level module parameter so you can write to the
/sys/module/mptbase/parameters/mpt_debug_level and have it take effect
in every ioc.
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (28 commits)
[SCSI] mpt fusion: Changes in mptctl.c for logging support
[SCSI] mpt fusion: Changes in mptfc.c mptlan.c mptsas.c and mptspi.c for logging support
[SCSI] mpt fusion: Changes in mptscsih.c for logging support
[SCSI] mpt fusion: Changes in mptbase.c for logging support
[SCSI] mpt fusion: logging support in Kconfig, Makefile, mptbase.h and addition of mptdebug.h
[SCSI] libsas: Fix potential NULL dereference in sas_smp_get_phy_events()
[SCSI] bsg: Fix build for CONFIG_BLOCK=n
[SCSI] aacraid: fix Sunrise Lake reset handling
[SCSI] aacraid: add SCSI SYNCHONIZE_CACHE range checking
[SCSI] add easyRAID to the no report luns blacklist
[SCSI] advansys: lindent and other large, uninteresting changes
[SCSI] aic79xx, aic7xxx: Fix incorrect width setting
[SCSI] qla2xxx: fix to honor ignored parameters in sysfs attributes
[SCSI] aacraid: draw line in sand, sundry cleanup and version update
[SCSI] iscsi_tcp: Turn off bounce buffers
[SCSI] libiscsi: fix cmd seqeunce number checking
[SCSI] iscsi_tcp, ib_iser Enable module refcounting for iscsi host template
[SCSI] libiscsi: make sure session is not blocked when removing host
[SCSI] libsas: Remove PCI dependencies
[SCSI] simscsi: convert to use the data buffer accessors
...
This patch contains changes in mptctl.c to support logging in MPT fusion drivers
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains changes in mptfc.c, mptlan.c, mptsas.c and mptspi.c to
support logging in MPT fusion drivers.
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains changes in mptscsih.c to support logging in MPT fusion
drivers.
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
A new sysfs attribute is added to retrieve and modify the debug level.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains changes in mptbase.c to support logging in MPT fusion
drivers.
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
A new module parameter mpt_debug_level is added to pass the debug level as
module parameter.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds a new file mptdebug.h in the fusion source directory,
which contains different debug macros. The existing debug macros and
flags are removed from the mptbase.h and Makefile In Kconfig a new
configuration parameter FUSION_LOGGING is added to enable/disable the
logging support during compile time.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Update help in Kconfig for mptfc driver to indicate the driver supports
Brocade FC 4G HBA.
signed-off-by: Gwendal Grignou <ggrignou@brocade.com>
Acked-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for Brocade 410/420 4Gbit FC HBAs.
They are re-branded LSI HBAs [LSI7104EP-LC/LSI7204EP-LC]
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The mptspi and mptsas drivers are modified to deregister from transport layer
if registration with PCI driver failed
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New sysfs scsi_host attributes are added to provide information about Firmware
version, BIOS version, MPI version and other product related information
signed-off-by: Sathya Praksh <sathya.prakash@lsi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix oops on reading from some i2o proc files (i2o_seq_show_driver_store() and
other) because their handlers uses "exec" field in struct i2o_controller
Signed-off-by: Vasily Averin <vvs@sw.ru>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to free i2o msg in case of error.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes access to memory that has not been allocated:
i2o_msg_get_wait() can returns errors different from I2O_QUEUE_EMPTY. But the
result is checked only against this code. If it is not I2O_QUEUE_EMPTY then
we dereference the error code as the pointer later.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a number of issues in i2o_cfg_passthru{,32}:
- i2o_msg_get_wait() return vaile is not checked;
- i2o_message memory leaks on error paths;
- infinite loop to sg_list_cleanup in passthru32
It's important issue because of i2o_cfg_passthru is used by raidutils for
monitorig controllers state, and in case of memory shortage it leads to the
node crash or disk IO stall.
[akpm@linux-foundation.org: fix null-ptr deref]
Signed-off-by: Vasily Averin <vvs@sw.ru>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make some offending drivers depend on it and set CONFIG_ARCH_NO_VIRT_TO_BUS
for ppc64 so that we don't build those drivers.
This gets PowerPC allmodconfig and allyesconfig much closer to building.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Al Viro <viro@ftp.linux.org.uk>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The I2O driver uses two semaphores as mutexes. Use the mutex API instead of
the (binary) semaphores.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
drivers/message/i2o/device.c:i2o_parm_field_get() unnecessarily passes
GFP_ATOMIC (along with GFP_KERNEL) to kmalloc() from a context that is not
atomic. Remove the pointless GFP_ATOMIC.
Signed-off-by: Satyam Sharma <ssatyam@cse.iitk.ac.in>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If there is IO going to the volume while a hidden disk is being torn down,
there is a case where we would return a DID_NO_CONNECT for IO sent to the
volume. The end result is the volume goes read-only. This problem is due to the
fact the firmware mapped target ids saved in per device object is phys_disk_num
for hidden raid components, and target_id for the volume. There is a single
case when both phys_disk_num and target_id are equal, so enters this issue. We
fix this issue by checking the tflags when the device is torned down,
insuring the IO being completed is meant for hidden raid component, not the
volume. In addition to this fix, there are a couple other cases to address
hidden raid components. For instance task_abort and device reset are not
supported by mpt fw for hidden raid components, a bus reset would be required
or target reset to volume.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
nice cosmetic cleaning of eh thread callback funtions
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
rewrite of mpt_fc_log_info to use the enum/defines from mpi_log_fc.h
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update assocated fusion sources with new support email address.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Note: needs to change i2o_dma_map_sg when the chaining sg is ready.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch for: http://bugzilla.kernel.org/show_bug.cgi?id=8426
A recent code cleanup that moved code from mptscsih to mptspi
inadvertently change the order some code was called. This caused
a massive slowdown (of 150x to 300x) on the CD/DVD drive on the
high-end HP Integrity servers.
Signed-off-by: Doug Chapman <doug.chapman@hp.com>
Acked-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/jazz_esp.c
Same changes made by both SCSI and SPARC trees: problem with UTF-8
conversion in the copyright.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
TODO: use scsi_for_each_sg().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] megaraid_sas: intercept cmd timeout and throttle io
[SCSI] fusion: Fix |/|| confusion
[SCSI] aic94xx: asd_clear_nexus should fail if the cleared task does not complete
[SCSI] aic7xxx: fix aicasm build failure with gcc-3.4.6
[SCSI] aacraid: apply commit config for reset_devices flag
[SCSI] sd: fix refcounting regression in suspend/resume routines
[SCSI] aacraid: fix panic on short Inquiry
[SCSI] aacraid: Correct sa platform support. (Was: [Bug 8469] Bad EIP value on pentium3 SMP kernel-2.6.21.1)
[SCSI] NCR53C9x: correct spelling mistake in deprecation notice
[SCSI] tgt: fix a rdma indirect transfer error bug
[SCSI] MegaRAID: Update MAINTAINERS email-id
[SCSI] stex: minor cleanup and version update
[SCSI] stex: fix reset recovery for console device
[SCSI] stex: extend hard reset wait time
[SCSI] stex: fix id mapping issue
[SCSI] ipr: Proper return codes for eh_dev_reset for SATA devices
[SCSI] zfcp: IO stall after deleting and path checker changes after reenabling zfcp devices
[SCSI] zfcp: avoid clutter in erp_dbf
There is no reason i2o_max_drivers must be a power of two. This patch
eliminates such a constraint.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Maximum number of I2O drivers which could be registered is configurable by
max_drivers module parameter.
But the module parameter is ignored and default value (I2O_MAX_DRIVERS = 8)
is used in the loops to notify all registered drivers.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i2o_driver_register() initalizes event queue for driver only when
drv->event is set. So similarly the event queue should be destroyed only
when drv->event is set in the error path. Otherwise destroy_workqueue()
will called with NULL.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are several cases where the fusion driver uses the logical || to
try to do an arithmetical or ... fix by replacing with |.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Refine some depends statements to limit their visibility to the
environments that are actually supported.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix various typos in kernel docs and Kconfigs, 2.6.21-rc4.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After host reset, the device are programmed to default asyn narrow nego.
We need to reprogram the parameter back to previous values. If the host
reset is called as a result of spi_dv_device() commands timing out, its
possible to get into an infinite loop of dv to host reset. This will
prevent that case, as we merely program old values. If host reset is
called outside context of domain validation, then we can call
spi_dv_device.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
For the places where we need a pointer to the mac header, it is still legal to
touch skb->mac.raw directly if just adding to, subtracting from or setting it
to another layer header.
This one also converts some more cases to skb_reset_mac_header() that my
regex missed as it had no spaces before nor after '=', ugh.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I2O subsystem has been broken in mainstream several months ago (after
2.6.18). Commit 4aff5e2333 from Jens
Axboe split struct request ->flags into two parts: cmd_type and
cmd_flags.
In i2o layer this patch has replaced flag REQ_SPECIAL by the according
cmd_type. However i2o has used REQ_SPECIAL not as command type but as
driver-specific flag for the debug purposes. As result all i2o requests
have type "special" now, are not processed to the hardware and fail with
I/O error:
i2o/hda:<3>Buffer I/O error on device i2o/hda, logical block 0
Buffer I/O error on device i2o/hda, logical block 0
Buffer I/O error on device i2o/hda, logical block 0
unable to read partition table
block-osm: device added (TID: 207): i2o/hda
The following patch removes the extra debug checks without any drawbacks and
restores the normal driver's work.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Acked-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This address the issue of VMWare guest OS being remounted as read-only
becuase the underlying device was held busy too long and at the
same time address Engenio MPP driver concerns over infinite retries.
This patch removes the code that snoops the SAM STATUS on busy, which
would be returning DID_BUS_BUSY, instead we return the status as is.
Retry hanlding seems to be properly handled in scsi_softirq_done,
where a busy sam status would only occurr for the time specified by
(cmd->allowed +1) * cmd->timeout_per_command.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Honour the return value of pci_enable_device(), which
seems to be a desirable thing to do:
2.6.20-rc4
gcc (GCC) 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)
CC [M] drivers/message/fusion/mptbase.o
drivers/message/fusion/mptbase.c: In function `mpt_resume':
drivers/message/fusion/mptbase.c:1541: warning: ignoring return value
of `pci_enable_device', declared with attribute warn_unused_result
It also in turn has mptscsih_resume() honour the return value of
mpt_resume()
I'm not sure about the handling of the other potential error cases
in mpt_resume(), of which there appear to be many. But this does
seem to be a good start.
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It seems that most of the code in mptscsih_resume() doesn't
do anything. This patch removes that code.
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This fix's an oops during driver load time. mptsas_probe calls
mpt_attach(over in mptbase.c). Inside that call, we read some
manufacturing config pages to setup some defaults. While reading the
config pages, the firmware doesn't complete the reply in time, and we
have a timeout. The timeout results in hardreset handler being called.
The hardreset handler calls all the fusion upper layer driver reset
callback handlers. The mptsas_ioc_reset function is the callback
handler in mptsas.c. So where I'm getting to, is mptsas_ioc_reset is
getting called before scsi_host_alloc is called, and the pointer ioc->sh
is NULL as well as the hostdata.
Signed-off-by: Judith Lebzelter <judith@osdl.org>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@sdl.org: dvb fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bump version, and fix email addr for lsi support
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
misc error handling bug fix's
- properly interpret iocstatus returned after task management request
- clear tmState after a failed doorbell
- cleanup mptscsih_taskmgmt_complete
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Return proper sas address to sas transport layer for parent phys that
form a wide port. Current implementation returns a different address
for each phy, incremented by one from the base address.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fusion firmware requires target reset following hotplug removal event,
with purpose to flush target outstanding request in fw. Current implementation
does the target resets from delayed work tasks, that in heavy load
conditions, take too long to be invoked, resulting in command time outs
This patch will issue target reset immediately from ISR context, and will
queue remaining target resets to be issued after the previous one completes.
The delayed work tasks are spawned during the target reset completion.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
inactive raid support, e.g. exposing hidden raid components
belonging to a volume that are inactive. Also misc bug fix's for
various raid asyn events.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
various string updates for iocstatus, logingo, and fw asyn events.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move some functions that only apply to the mptspi module over from mptscsih.c
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for greater than 255 target and luns.
Kill the hd->Target[] field, and change all references
of bus_id/target_id, to channel/id.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Here are the lastest mpi headers for mpt fusion driver, which defines
the firmware to driver interface.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes the mptctl pass through available if
the mptsas driver is selected. Without this patch
if mptsas is the only fusion driver chosen, then
the mptctl is not presented as an option.
smp_utils uses the mptctl driver to pass SAS SMP
functions through a MPT SAS HBA.
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
