Platform parameter to enable automatic FIFO configuration when
the codec is in Mode1 or Mode7 FIFO mode.
When this mode is selected, the controls for changing
nSample (in Mode1), and UTHR (in Mode7) are not added.
The driver configures the FIFO configuration based on
the stream's period size in a way, that every burst will
read period size of data from the host.
In Mode7 we need to use a formula, which gives close enough
aproximation for the burst length from the host point
of view.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Replace the hardwired latency definition with platform data
parameter, and simplify the nSample parameter calculation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
All current users of pm_qos_add_request() have the ability to supply
the memory required by the pm_qos routines, so make them do this and
eliminate the kmalloc() with pm_qos_add_request(). This has the
double benefit of making the call never fail and allowing it to be
called from atomic context.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: mark gross <markgross@thegnar.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Specified ID is necessary, when some codecs are used with FSI.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add hw_params to snd_soc_dai_ops,
because board specific set_rate is needed
when FSI was used as master mode.
This patch remove fsi_clk_ctrl from fsi_dai_startup,
because clock should be disabled before set_rate.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no necessity that each bit in this area has the meaning.
This patch modify it to sequence number
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When using poll() to wait for the next period -- or avail_min samples --
one gets a consistent delay for each system call that is usually just a
little short of the selected period time. However, When using
snd_pcm_read/write(), one gets a jittery delay that alternates between
less than a millisecond and approximately two period times. This is
caused by snd_pcm_lib_{read,write}1() transferring any available samples
to the user's buffer and adjusting the application pointer prior to
sleeping to the end of the current period. When the next period
interrupt occurs, there is then less than avail_min samples remaining to
be transferred in the period, so we end up sleeping until a second
period occurs.
This is solved by using runtime->twake as the number of samples needed
for a wakeup in addition to selecting the proper wait queue to wake in
snd_pcm_update_state(). This requires twake to be non-zero when used
by snd_pcm_lib_{read,write}1() even if avail_min is zero.
Signed-off-by: Dave Dillow <dave@thedillows.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This change wipes out a hardcoded macro, which enables codec bias
level control. Now is_powered_on_standby value shall be used instead.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some systems codecs need to configure some registers before and after
powering down some of their part. As a convenience add a macro for that.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This defines the 24bps and 40bps (8khz sample rate) G.723 codec
formats. They are going to be used once I submit the driver for
an mpeg4/g723 compression card.
I've updated the signed value to -1 as per Takashi's comments
since these are non-linear formats.
Signed-off-by: Ben Collins <bcollins@bluecherry.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (250 commits)
ALSA: hda: Storage class should be before const qualifier
ASoC: tpa6130a2: Remove CPVSS and HPVdd supplies
ASoC: tpa6130a2: Define output pins with SND_SOC_DAPM_OUTPUT
ASoC: sdp4430 - add sdp4430 pcm ops to DAI.
ASoC: TWL6040: Enable earphone path in codec
ASoC: SDP4430: Add support for Earphone speaker
ASoC: SDP4430: Add sdp4430 machine driver
ASoC: tlv320dac33: Avoid powering off while in BIAS_OFF
ASoC: tlv320dac33: Use dev_dbg in dac33_hard_power function
ALSA: sound/pci/asihpi: Use kzalloc
ALSA: hdmi - dont fail on extra nodes
ALSA: intelhdmi - add id for the CougarPoint chipset
ALSA: intelhdmi - user friendly codec name
ALSA: intelhdmi - add dependency on SND_DYNAMIC_MINORS
ALSA: asihpi: incorrect range check
ALSA: asihpi: testing the wrong variable
ALSA: es1688: add pedantic range checks
ARM: McBSP: Add support for omap4 in McBSP driver
ARM: McBSP: Fix request for irq in OMAP4
OMAP: McBSP: Add 32-bit mode support
...
This patch is adding a new control which has the following capabilities:
- tlv
- variable data size (for instance, 7 ou 8 bit)
- double mixer
- data range centered around 0
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Acked-by: Liam Girdwood <lrg@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the register for the volume needs invert, than the inversion
need to be done from the chip maximum, and not from the platform
dependent limit.
Introduce soc_mixer_control.platform_max value, which initially
equals to chip maximum.
The snd_soc_limit_volume function only modify the platform_max,
all volsw_info call returns this as well.
The .max value holds the chip default (maximum), and it is used
for the inversion, if it is needed.
Additional check in the volsw_info call has been added to check
the validity of the platform_max in case, when custom macros
used by codec drivers are not initializing it correctly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch changes the string based list management to a handle base
implementation to help with the hot path use of pm-qos, it also renames
much of the API to use "request" as opposed to "requirement" that was
used in the initial implementation. I did this because request more
accurately represents what it actually does.
Also, I added a string based ABI for users wanting to use a string
interface. So if the user writes 0xDDDDDDDD formatted hex it will be
accepted by the interface. (someone asked me for it and I don't think
it hurts anything.)
This patch updates some documentation input I got from Randy.
Signed-off-by: markgross <mgross@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
As well as allowing DAPM pins to be marked as ignoring suspend allow DAI
links to be similarly marked. This is primarily intended for digital
links between CODECs and non-CPU devices such as basebands in mobile
phones and will suppress all suspend calls for the DAI link. It is
likely that this will need to be revisited if used with devices which
are part of the SoC CPU.
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices can usefully run audio while the Linux system is suspended.
One of the most common examples is smartphone systems, which are normally
designed to allow audio to be run between the baseband and the CODEC
without passing through the CPU and so can suspend the CPU when on a
voice call for additional power savings.
Support such systems by providing an API snd_soc_dapm_ignore_suspend().
This can be used to mark DAPM endpoints as not being sensitive to
system suspend. When the system is being suspended paths between
endpoints which are marked as ignoring suspend will be kept active.
Both source and sink must be marked, and there must already be an
active path between the two endpoints prior to suspend.
When paths are active over suspend the bias management will hold the
device bias in the ON state. This is used to avoid suspending the
CODEC while it is still in use.
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We now manage suspend within the main power analysis rather than by
flipping the state of widgets.
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ESS ES968 chip is nothing more then a PnP companion
for a non-PnP audio chip. It was paired with non-PnP ESS' chips:
ES688 and ES1688. The ESS' audio chips are handled by the es1688
driver in native mode. The PnP cards are handled by the ES968
driver in SB compatible mode.
Move the ES968 chip handling to the es1688 driver so the driver
can handle both PnP and non-PnP cards. The es968 is removed.
Also, a new PnP id is added for the card I acquired (the change
was tested on this card).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allocate the snd_es1688 during the snd_card allocation.
This allows to remove the card pointer from the snd_es1688 structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 6f3991152f.
Since core has now support for limiting the volume on controls this
patch is not needed. Furthermore, this patch actually prevents the core
to set new volume on the TPA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for the core to limit the maximum volume on an
existing control.
The function will modify the soc_mixer_control.max value
of the given control.
The new value must be lower than the original one (chip maximum)
If there is a need for limiting a gain on a given control,
than machine drivers can do the following in their
snd_soc_dai_link.init function:
snd_soc_limit_volume(codec, "TPA6140A2 Headphone Playback Volume", 21);
This will modify the original 31 (chip maximum) to 21, so user
space will not be able to set the gain higher than this.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for platform dependent gain limiting on the
tpa6130a2 (and tpa6140a2) Headset amplifier.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Handle the reset GPIO within the codec driver in order to follow
the startup protocol for the tlv320aic3x codecs.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM9090 is a high performance low power audio subsystem, including
headphone and class D speaker drivers.
Note that this driver is a standalone CODEC driver and so is only
immediately suitable for use with the WM9090 as a standalone sound card
taking line inputs, or with a DAC with no software control. The pending
ASoC multi-CODEC support will expand the range of systems that can use
the driver, or system-specific adaptations can be made.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for Philips UDA1345 CODEC. The CODEC has only
volume control, de-emphasis, mute, DC filtering and power control features.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
One of the features of the multi CODEC work is that it embeds a struct
device in the CODEC to provide diagnostics via a sysfs class rather than
via the device tree, at which point it's much better to use the struct
device private data rather than having two places to store it. Provide
an accessor function to allow this change to be made more easily, and
update all the CODEC drivers are updated.
To ensure use of the accessor the private data structure member is
renamed, meaning that if code developed with older an older core that
still uses private_data is merged it will fail to build.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
[Note that this is a backported version for 2.6.34.
Upstream commit is fd23b7dee]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We actually pass an array of 7 chars not 5.
This silences a smatch warning.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some systems provide both mechanical and electrical detection of jack
status changes. On such systems power savings can be achieved by only
enabling the electrical detection methods when physical insertion has
been detected.
Begin supporting such systems by providing a notifier for jack status
changes which can be used to trigger any reconfiguration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices provide support for detection of a small number of
buttons on their jacks. One common implementation provides a single
button, implemented by shorting the microphone to ground and detected
along with microphone presence detection by detecting varying current
draws on the microphone bias signal.
Provide support for up to three buttons via the jack interface. These
default to reporting BTN_n but an API is provided to allow these to
be remapped to other keys by the machine driver where it knows what
the keys are. More keys can be added with ease if required.
This is only intended to support simple accessory button designs. If
the interface is limiting then either creating a child device for the
accessory or accessing the input device in the jack directly is
recommended.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8904 allows microphone detection signals to be brought out as
alternate functions of the GPIO signals which can be detected using
interrupt inputs on the CPU. Allow this to be configured using
platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Provide platform data allowing the configuration of the GPIO pins
on the WM8904 to be selected, allowing alternate functions to be
enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Support use of the WM8903 IRQ for reporting of microphone presence
and short detection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently used to detect completion of the write sequencer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Provide support for WM8903 microphone presence and short detection
using the GPIOs to route out a logic signal suitable for handling
using snd_soc_jack_add_gpios() on the processor GPIOs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow users to pass in a default configuration for the GPIOs of
the WM8903 as platform data. This allows configuration of the pin
muxing of the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow pins to be forced on regardless of their power state. This is
intended for use with microphone bias supplies which need to be
enabled in order to support microphone detection - in systems without
appropriate hardware leaving the microphone unbiased when not in use
saves power.
The force done at power check time in order to avoid disrupting other
power detection logic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Platform data option for the codec to keep the BCLK clock
continuously running in FIFO modes (codec master).
OMAP3 McBSP when in slave mode needs continuous BCLK running
on the serial bus in order to operate correctly.
Since in FIFO mode the DAC33 can also shut down the BCLK clock
and enable it only when it is needed, let the platforms decide
if the CPU side needs the BCLK running or not.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The flag is no longer used in the code so it just wastes a bit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8960 headphone outputs can be run in capless mode with OUT3
used to drive a pseudo ground for the headphone drivers. In this
mode the mono mixer is not used, the mixer should be turned on
in concert with the headphone output drivers and the device bias
levels are managed differently.
Also tweak the existing bias management to remove the use of active
discharge while we're at it since that's often audible.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Avoids machine files having to peer into sound/soc which is a bit
rude and icky.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The delay callback can be used by the core to query the delay
on the dai caused by FIFO or delay in the platform side.
In case if both CPU and CODEC dai has FIFO the delay reported
by each will be added to form the full delay on the chain.
If none of the dai has FIFO, than the delay will be kept as
zero.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we are to have a snd_soc_dai i.e, cpu_dai and codec_dai, shared among two
or more dai_links we need to log the number of active users of the dai.
For that, we change semantics of the snd_soc_dai.active flag from indicator
to reference counter.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order for having snd_soc_dais shared among two or more dai_links,
remove the relatively global runtime field from the struct snd_soc_dai
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Passing pointer to relevant dai_link provides easier reach to the
ASoC tree in suspend/resume of snd_soc_platform. It also provides
direct access to the dai at the other end of the dai_link.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make the pmdown_time a per-card setting rather than a global one,
initialised before the card initialisation runs. This allows cards
to override the default setting if it makes sense to do so (for
example, due to an unavoidable pop).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM2000 is a low power, high quality handset receiver speaker
driver with Wolfson myZone™ Ambient Noise Cancellation (ANC). It
provides enhanced voice communication quality in a noisy environment
if the handset acoustics are designed appropriately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add a bit to the CODEC structure indicating if a cache sync is required.
By default this will be set if a cache only write is done to a soc-cache
register cache. This allows us to avoid syncing the cache back after
using cache only writes if there were no changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently the soc-cache code will always write to the device, meaning
that we need the device to be powered and active at pretty much all
times the system is active. Allowing cache only writes lays some
groundwork for future enhancements to allow devices to be put into a
full off state when the audio subsystem is idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Clemens Ladisch noted for hw_ptr_removal in "cleanup & merge hw_ptr
update functions" commit:
"It is possible for the status/delay ioctls to be called when the sound
card's pointer register alreay shows a position at the beginning of the
new period, but immediately before the interrupt is actually executed.
(This happens regularly on a SMP machine with mplayer.) When that
happens, the code thinks that the position must be at least one period
ahead of the current position and drops an entire buffer of data."
Return back the hw_ptr_interrupt variable. The last interrupt pointer
is always computed from the latest hw_ptr instead of tracking it
separately (in this case all hw_ptr checks and modifications might
influence also hw_ptr_interrupt and it is difficult to keep it
consistent).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Several shortcuts for popular uses of some of SOC_ENUM_* and
SOC_VALUE_ENUM_* macros.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many macros from include/sound/soc-dapm.h take an array and a number of
elements in it as arguments, whereas most users use static arrays and use
"x, ARRAY_SIZE(x)" as arguments. This patch adds simplified versions of
those macros, calling ARRAY_SIZE() internally.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.oc.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently ASoC always maintains the bias of the CODEC while the system
is active. With older mobile CODECs this is required since the outputs
are referenced to a non-zero voltage and enabling or disabling this
voltage without audible pops or clicks in the output takes too long to
do when starting or stopping audio.
As a result of features such as ground referenced outputs and class D
speaker drivers current generation devices are able to power on and off
much more quickly without these system level issues so provide a new
flag idle_bias_off in snd_soc_codec which will cause the core to turn
off the CODEC bias. The distinction between STANDBY and OFF is still
maintained. This is partly for consistency but also allows for
potential future extensions such as per-machine overrides or deferring
the bias removal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This change fixes the "ALSA: pcm_lib - optimize wake_up() calls for PCM I/O"
commit. New sleeping queue is introduced to separate user space and kernel
space wake_ups. runtime->nowake is renamed to twake (transfer wake).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add possibility to configure the burst mode BCLK divider through platform
data structure.
The BCLK divider changes the actual speed of the serial bus in burst mode,
which is faster than the sampling frequency of the running stream.
In this way platforms can experiment with the optimal burst speed without
the need to modify the codec driver itself.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
pgprot_noncached() can be set for vmalloc'ed buffers safely, and we'd
need non-cached behavior more or less, even for the intermediate ring-
buffers.
Now snd_pcm_lib_mmap_vmalloc() is added as the common PCM mmap callback
that is coupled with snd_pcm_lib_alloc_vmalloc_buffer() & co.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a new function to look up a quirk entry with the given PCI SSID
instead of a pci device pointer. This can be used when the searched ID
is overridden for debugging or such a purpose.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
tpa6140a2 uses different names for the regulators.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As noted by pl bossart <bossart.nospam@gmail.com>, the PCM I/O routines
(snd_pcm_lib_write1, snd_pcm_lib_read1) should block wake_up() calls
until all samples are not processed.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Do general cleanup in snd_pcm_update_hw_ptr*() routines and merge them.
The main change is hw_ptr_interrupt variable removal to simplify code
logic. This variable can be computed directly from hw_ptr.
Ensure that updated hw_ptr is not lower than previous one (it was possible
with old code in some obscure situations when interrupt was delayed or
the lowlevel driver returns wrong ring buffer position value).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
In some debug cases, it might be usefull to see previous ring buffer
positions to determine position problems from the lowlevel drivers.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This is one of Sound Blaster Pro compatible chipsets which is supported
by Linux OSS driver and was missing native supoort for ALSA.
The Jazz16 audio codec is Crystal CS4216 which is capable
of playback and recording up to 48 kHz stereo.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8955 is a low power, high quality stereo DAC with integrated
headphone and loudspeaker amplifiers, designed to reduce external
component requirements in portable digital audio applications. This is
an initial driver implementing support for the majority of the
functionality in the device, currently OUT3 is not supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
There are now five copies of the code to allocate a PCM buffer using
vmalloc(). Add a sixth in the core so that the others can be removed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8904 is a high performance ultra-low power stereo CODEC
optimised for portable audio applications, with features including
a class W amplifier, FLL with free running mode, Mobile ReTune and
ground referenced headphone and line outputs.
Support for some features, most particularly the digital microphone
interface, is not yet present.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
