renegade-project/linux-next
2
0
Fork 0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-30 16:13:54 +08:00
Code

mtd: spi-nor: Add support for S3AN spi-nor devices

Browse Source 
Xilinx Spartan-3AN FPGAs contain an In-System Flash where they keep
their configuration data and (optionally) some user data.

The protocol of this flash follows most of the spi-nor standard. With
the following differences:

- Page size might not be a power of two.
- The address calculation (default addressing mode).
- The spi nor commands used.

Protocol is described on Xilinx User Guide UG333

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
This commit is contained in:
Ricardo Ribalda 2016-12-02 12:31:44 +01:00 committed by Cyrille Pitchen
parent 0cf1725676
commit e99ca98f1d
2 changed files with 161 additions and 5 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

154
drivers/mtd/spi-nor/spi-nor.c
View File

@ -75,6 +75,12 @@ struct flash_info {
* bit. Must be used with
* SPI_NOR_HAS_LOCK.
*/
#define SPI_S3AN BIT(10) /*
* Xilinx Spartan 3AN In-System Flash
* (MFR cannot be used for probing
* because it has the same value as
* ATMEL flashes)
*/
};
#define JEDEC_MFR(info) ((info)->id[0])
@ -217,6 +223,21 @@ static inline int set_4byte(struct spi_nor *nor, const struct flash_info *info,
return nor->write_reg(nor, SPINOR_OP_BRWR, nor->cmd_buf, 1);
}
}
static int s3an_sr_ready(struct spi_nor *nor)
{
int ret;
u8 val;
ret = nor->read_reg(nor, SPINOR_OP_XRDSR, &val, 1);
if (ret < 0) {
dev_err(nor->dev, "error %d reading XRDSR\n", (int) ret);
return ret;
}
return !!(val & XSR_RDY);
}
static inline int spi_nor_sr_ready(struct spi_nor *nor)
{
int sr = read_sr(nor);
@ -238,7 +259,11 @@ static inline int spi_nor_fsr_ready(struct spi_nor *nor)
static int spi_nor_ready(struct spi_nor *nor)
{
int sr, fsr;
sr = spi_nor_sr_ready(nor);
if (nor->flags & SNOR_F_READY_XSR_RDY)
sr = s3an_sr_ready(nor);
else
sr = spi_nor_sr_ready(nor);
if (sr < 0)
return sr;
fsr = nor->flags & SNOR_F_USE_FSR ? spi_nor_fsr_ready(nor) : 1;
@ -319,6 +344,24 @@ static void spi_nor_unlock_and_unprep(struct spi_nor *nor, enum spi_nor_ops ops)
mutex_unlock(&nor->lock);
}
/*
* This code converts an address to the Default Address Mode, that has non
* power of two page sizes. We must support this mode because it is the default
* mode supported by Xilinx tools, it can access the whole flash area and
* changing over to the Power-of-two mode is irreversible and corrupts the
* original data.
* Addr can safely be unsigned int, the biggest S3AN device is smaller than
* 4 MiB.
*/
static loff_t spi_nor_s3an_addr_convert(struct spi_nor *nor, unsigned int addr)
{
unsigned int offset = addr;
offset %= nor->page_size;
return ((addr - offset) << 1) | offset;
}
/*
* Initiate the erasure of a single sector
*/
@ -327,6 +370,9 @@ static int spi_nor_erase_sector(struct spi_nor *nor, u32 addr)
u8 buf[SPI_NOR_MAX_ADDR_WIDTH];
int i;
if (nor->flags & SNOR_F_S3AN_ADDR_DEFAULT)
addr = spi_nor_s3an_addr_convert(nor, addr);
if (nor->erase)
return nor->erase(nor, addr);
@ -368,7 +414,7 @@ static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
return ret;
/* whole-chip erase? */
if (len == mtd->size) {
if (len == mtd->size && !(nor->flags & SNOR_F_NO_OP_CHIP_ERASE)) {
unsigned long timeout;
write_enable(nor);
@ -782,6 +828,19 @@ static int spi_nor_is_locked(struct mtd_info *mtd, loff_t ofs, uint64_t len)
.addr_width = (_addr_width), \
.flags = (_flags),
#define S3AN_INFO(_jedec_id, _n_sectors, _page_size) \
.id = { \
((_jedec_id) >> 16) & 0xff, \
((_jedec_id) >> 8) & 0xff, \
(_jedec_id) & 0xff \
}, \
.id_len = 3, \
.sector_size = (8*_page_size), \
.n_sectors = (_n_sectors), \
.page_size = _page_size, \
.addr_width = 3, \
.flags = SPI_NOR_NO_FR | SPI_S3AN,
/* NOTE: double check command sets and memory organization when you add
* more nor chips. This current list focusses on newer chips, which
* have been converging on command sets which including JEDEC ID.
@ -1014,6 +1073,13 @@ static const struct flash_info spi_nor_ids[] = {
{ "cat25c09", CAT25_INFO( 128, 8, 32, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) },
{ "cat25c17", CAT25_INFO( 256, 8, 32, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) },
{ "cat25128", CAT25_INFO(2048, 8, 64, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) },
/* Xilinx S3AN Internal Flash */
{ "3S50AN", S3AN_INFO(0x1f2200, 64, 264) },
{ "3S200AN", S3AN_INFO(0x1f2400, 256, 264) },
{ "3S400AN", S3AN_INFO(0x1f2400, 256, 264) },
{ "3S700AN", S3AN_INFO(0x1f2500, 512, 264) },
{ "3S1400AN", S3AN_INFO(0x1f2600, 512, 528) },
{ },
};
@ -1054,7 +1120,12 @@ static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len,
return ret;
while (len) {
ret = nor->read(nor, from, len, buf);
loff_t addr = from;
if (nor->flags & SNOR_F_S3AN_ADDR_DEFAULT)
addr = spi_nor_s3an_addr_convert(nor, addr);
ret = nor->read(nor, addr, len, buf);
if (ret == 0) {
/* We shouldn't see 0-length reads */
ret = -EIO;
@ -1175,8 +1246,23 @@ static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
for (i = 0; i < len; ) {
ssize_t written;
loff_t addr = to + i;
page_offset = (to + i) & (nor->page_size - 1);
/*
* If page_size is a power of two, the offset can be quickly
* calculated with an AND operation. On the other cases we
* need to do a modulus operation (more expensive).
* Power of two numbers have only one bit set and we can use
* the instruction hweight32 to detect if we need to do a
* modulus (do_div()) or not.
*/
if (hweight32(nor->page_size) == 1) {
page_offset = addr & (nor->page_size - 1);
} else {
uint64_t aux = addr;
page_offset = do_div(aux, nor->page_size);
}
WARN_ONCE(page_offset,
"Writing at offset %zu into a NOR page. Writing partial pages may decrease reliability and increase wear of NOR flash.",
page_offset);
@ -1184,8 +1270,11 @@ static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
page_remain = min_t(size_t,
nor->page_size - page_offset, len - i);
if (nor->flags & SNOR_F_S3AN_ADDR_DEFAULT)
addr = spi_nor_s3an_addr_convert(nor, addr);
write_enable(nor);
ret = nor->write(nor, to + i, page_remain, buf + i);
ret = nor->write(nor, addr, page_remain, buf + i);
if (ret < 0)
goto write_err;
written = ret;
@ -1312,6 +1401,47 @@ static int spi_nor_check(struct spi_nor *nor)
return 0;
}
static int s3an_nor_scan(const struct flash_info *info, struct spi_nor *nor)
{
int ret;
u8 val;
ret = nor->read_reg(nor, SPINOR_OP_XRDSR, &val, 1);
if (ret < 0) {
dev_err(nor->dev, "error %d reading XRDSR\n", (int) ret);
return ret;
}
nor->erase_opcode = SPINOR_OP_XSE;
nor->program_opcode = SPINOR_OP_XPP;
nor->read_opcode = SPINOR_OP_READ;
nor->flags |= SNOR_F_NO_OP_CHIP_ERASE;
/*
* This flashes have a page size of 264 or 528 bytes (known as
* Default addressing mode). It can be changed to a more standard
* Power of two mode where the page size is 256/512. This comes
* with a price: there is 3% less of space, the data is corrupted
* and the page size cannot be changed back to default addressing
* mode.
*
* The current addressing mode can be read from the XRDSR register
* and should not be changed, because is a destructive operation.
*/
if (val & XSR_PAGESIZE) {
/* Flash in Power of 2 mode */
nor->page_size = (nor->page_size == 264) ? 256 : 512;
nor->mtd.writebufsize = nor->page_size;
nor->mtd.size = 8 * nor->page_size * info->n_sectors;
nor->mtd.erasesize = 8 * nor->page_size;
} else {
/* Flash in Default addressing mode */
nor->flags |= SNOR_F_S3AN_ADDR_DEFAULT;
}
return 0;
}
int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
{
const struct flash_info *info = NULL;
@ -1359,6 +1489,14 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
mutex_init(&nor->lock);
/*
* Make sure the XSR_RDY flag is set before calling
* spi_nor_wait_till_ready(). Xilinx S3AN share MFR
* with Atmel spi-nor
*/
if (info->flags & SPI_S3AN)
nor->flags |= SNOR_F_READY_XSR_RDY;
/*
* Atmel, SST, Intel/Numonyx, and others serial NOR tend to power up
* with the software protection bits set
@ -1517,6 +1655,12 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
nor->read_dummy = spi_nor_read_dummy_cycles(nor);
if (info->flags & SPI_S3AN) {
ret = s3an_nor_scan(info, nor);
if (ret)
return ret;
}
dev_info(dev, "%s (%lld Kbytes)\n", info->name,
(long long)mtd->size >> 10);

12
include/linux/mtd/spi-nor.h
View File

@ -68,6 +68,15 @@
#define SPINOR_OP_WRDI 0x04 /* Write disable */
#define SPINOR_OP_AAI_WP 0xad /* Auto address increment word program */
/* Used for S3AN flashes only */
#define SPINOR_OP_XSE 0x50 /* Sector erase */
#define SPINOR_OP_XPP 0x82 /* Page program */
#define SPINOR_OP_XRDSR 0xd7 /* Read status register */
#define XSR_PAGESIZE BIT(0) /* Page size in Po2 or Linear */
#define XSR_RDY BIT(7) /* Ready */
/* Used for Macronix and Winbond flashes. */
#define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */
#define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */
@ -119,6 +128,9 @@ enum spi_nor_ops {
enum spi_nor_option_flags {
SNOR_F_USE_FSR = BIT(0),
SNOR_F_HAS_SR_TB = BIT(1),
SNOR_F_NO_OP_CHIP_ERASE = BIT(2),
SNOR_F_S3AN_ADDR_DEFAULT = BIT(3),
SNOR_F_READY_XSR_RDY = BIT(4),
};
/**