Merge branch 'gic' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64 into next/cleanup

* 'gic' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
  irqchip: gic: Perform the gic_secondary_init() call via CPU notifier
  irqchip: gic: Call handle_bad_irq() directly
  arm: Move chained_irq_(enter|exit) to a generic file
  arm: Move the set_handle_irq and handle_arch_irq declarations to asm/irq.h
  + Linux 3.9-rc3

Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/mfd/ab8500.txt

@@ -13,9 +13,6 @@ Required parent device properties:
                                   4 = active high level-sensitive
                                   8 = active low level-sensitive
 
-Optional parent device properties:
-- reg                    : contains the PRCMU mailbox address for the AB8500 i2c port
-
 The AB8500 consists of a large and varied group of sub-devices:
 
 Device                     IRQ Names              Supply Names   Description
@@ -86,9 +83,8 @@ Non-standard child device properties:
    - stericsson,amic2-bias-vamic1           : Analoge Mic wishes to use a non-standard Vamic
    - stericsson,earpeice-cmv                : Earpeice voltage (only: 950 | 1100 | 1270 | 1580)
 
-ab8500@5 {
+ab8500 {
          compatible = "stericsson,ab8500";
-         reg = <5>; /* mailbox 5 is i2c */
          interrupts = <0 40 0x4>;
          interrupt-controller;
          #interrupt-cells = <2>;

Documentation/devicetree/bindings/tty/serial/of-serial.txt

@@ -11,6 +11,9 @@ Required properties:
 	- "nvidia,tegra20-uart"
 	- "nxp,lpc3220-uart"
 	- "ibm,qpace-nwp-serial"
+	- "altr,16550-FIFO32"
+	- "altr,16550-FIFO64"
+	- "altr,16550-FIFO128"
 	- "serial" if the port type is unknown.
 - reg : offset and length of the register set for the device.
 - interrupts : should contain uart interrupt.

Documentation/input/alps.txt

@@ -3,10 +3,26 @@ ALPS Touchpad Protocol
 
 Introduction
 ------------
+Currently the ALPS touchpad driver supports five protocol versions in use by
+ALPS touchpads, called versions 1, 2, 3, 4 and 5.
 
-Currently the ALPS touchpad driver supports four protocol versions in use by
-ALPS touchpads, called versions 1, 2, 3, and 4. Information about the various
-protocol versions is contained in the following sections.
+Since roughly mid-2010 several new ALPS touchpads have been released and
+integrated into a variety of laptops and netbooks.  These new touchpads
+have enough behavior differences that the alps_model_data definition
+table, describing the properties of the different versions, is no longer
+adequate.  The design choices were to re-define the alps_model_data
+table, with the risk of regression testing existing devices, or isolate
+the new devices outside of the alps_model_data table.  The latter design
+choice was made.  The new touchpad signatures are named: "Rushmore",
+"Pinnacle", and "Dolphin", which you will see in the alps.c code.
+For the purposes of this document, this group of ALPS touchpads will
+generically be called "new ALPS touchpads".
+
+We experimented with probing the ACPI interface _HID (Hardware ID)/_CID
+(Compatibility ID) definition as a way to uniquely identify the
+different ALPS variants but there did not appear to be a 1:1 mapping.
+In fact, it appeared to be an m:n mapping between the _HID and actual
+hardware type.
 
 Detection
 ---------
@@ -20,9 +36,13 @@ If the E6 report is successful, the touchpad model is identified using the "E7
 report" sequence: E8-E7-E7-E7-E9. The response is the model signature and is
 matched against known models in the alps_model_data_array.
 
-With protocol versions 3 and 4, the E7 report model signature is always
-73-02-64. To differentiate between these versions, the response from the
-"Enter Command Mode" sequence must be inspected as described below.
+For older touchpads supporting protocol versions 3 and 4, the E7 report
+model signature is always 73-02-64. To differentiate between these
+versions, the response from the "Enter Command Mode" sequence must be
+inspected as described below.
+
+The new ALPS touchpads have an E7 signature of 73-03-50 or 73-03-0A but
+seem to be better differentiated by the EC Command Mode response.
 
 Command Mode
 ------------
@@ -47,6 +67,14 @@ address of the register being read, and the third contains the value of the
 register. Registers are written by writing the value one nibble at a time
 using the same encoding used for addresses.
 
+For the new ALPS touchpads, the EC command is used to enter command
+mode. The response in the new ALPS touchpads is significantly different,
+and more important in determining the behavior.  This code has been
+separated from the original alps_model_data table and put in the
+alps_identify function.  For example, there seem to be two hardware init
+sequences for the "Dolphin" touchpads as determined by the second byte
+of the EC response.
+
 Packet Format
 -------------
 
@@ -187,3 +215,28 @@ There are several things worth noting here.
     well.
 
 So far no v4 devices with tracksticks have been encountered.
+
+ALPS Absolute Mode - Protocol Version 5
+---------------------------------------
+This is basically Protocol Version 3 but with different logic for packet
+decode.  It uses the same alps_process_touchpad_packet_v3 call with a
+specialized decode_fields function pointer to correctly interpret the
+packets.  This appears to only be used by the Dolphin devices.
+
+For single-touch, the 6-byte packet format is:
+
+ byte 0:    1    1    0    0    1    0    0    0
+ byte 1:    0   x6   x5   x4   x3   x2   x1   x0
+ byte 2:    0   y6   y5   y4   y3   y2   y1   y0
+ byte 3:    0    M    R    L    1    m    r    l
+ byte 4:   y10  y9   y8   y7  x10   x9   x8   x7
+ byte 5:    0   z6   z5   z4   z3   z2   z1   z0
+
+For mt, the format is:
+
+ byte 0:    1    1    1    n3   1   n2   n1   x24
+ byte 1:    1   y7   y6    y5  y4   y3   y2    y1
+ byte 2:    ?   x2   x1   y12 y11  y10   y9    y8
+ byte 3:    0  x23  x22   x21 x20  x19  x18   x17
+ byte 4:    0   x9   x8    x7  x6   x5   x4    x3
+ byte 5:    0  x16  x15   x14 x13  x12  x11   x10

Documentation/networking/tuntap.txt

@@ -105,6 +105,83 @@ Copyright (C) 1999-2000 Maxim Krasnyansky <max_mk@yahoo.com>
      Proto [2 bytes]
      Raw protocol(IP, IPv6, etc) frame.
 
+  3.3 Multiqueue tuntap interface:
+
+  From version 3.8, Linux supports multiqueue tuntap which can uses multiple
+  file descriptors (queues) to parallelize packets sending or receiving. The
+  device allocation is the same as before, and if user wants to create multiple
+  queues, TUNSETIFF with the same device name must be called many times with
+  IFF_MULTI_QUEUE flag.
+
+  char *dev should be the name of the device, queues is the number of queues to
+  be created, fds is used to store and return the file descriptors (queues)
+  created to the caller. Each file descriptor were served as the interface of a
+  queue which could be accessed by userspace.
+
+  #include <linux/if.h>
+  #include <linux/if_tun.h>
+
+  int tun_alloc_mq(char *dev, int queues, int *fds)
+  {
+      struct ifreq ifr;
+      int fd, err, i;
+
+      if (!dev)
+          return -1;
+
+      memset(&ifr, 0, sizeof(ifr));
+      /* Flags: IFF_TUN   - TUN device (no Ethernet headers)
+       *        IFF_TAP   - TAP device
+       *
+       *        IFF_NO_PI - Do not provide packet information
+       *        IFF_MULTI_QUEUE - Create a queue of multiqueue device
+       */
+      ifr.ifr_flags = IFF_TAP | IFF_NO_PI | IFF_MULTI_QUEUE;
+      strcpy(ifr.ifr_name, dev);
+
+      for (i = 0; i < queues; i++) {
+          if ((fd = open("/dev/net/tun", O_RDWR)) < 0)
+             goto err;
+          err = ioctl(fd, TUNSETIFF, (void *)&ifr);
+          if (err) {
+             close(fd);
+             goto err;
+          }
+          fds[i] = fd;
+      }
+
+      return 0;
+  err:
+      for (--i; i >= 0; i--)
+          close(fds[i]);
+      return err;
+  }
+
+  A new ioctl(TUNSETQUEUE) were introduced to enable or disable a queue. When
+  calling it with IFF_DETACH_QUEUE flag, the queue were disabled. And when
+  calling it with IFF_ATTACH_QUEUE flag, the queue were enabled. The queue were
+  enabled by default after it was created through TUNSETIFF.
+
+  fd is the file descriptor (queue) that we want to enable or disable, when
+  enable is true we enable it, otherwise we disable it
+
+  #include <linux/if.h>
+  #include <linux/if_tun.h>
+
+  int tun_set_queue(int fd, int enable)
+  {
+      struct ifreq ifr;
+
+      memset(&ifr, 0, sizeof(ifr));
+
+      if (enable)
+         ifr.ifr_flags = IFF_ATTACH_QUEUE;
+      else
+         ifr.ifr_flags = IFF_DETACH_QUEUE;
+
+      return ioctl(fd, TUNSETQUEUE, (void *)&ifr);
+  }
+
 Universal TUN/TAP device driver Frequently Asked Question.
    
 1. What platforms are supported by TUN/TAP driver ?

Documentation/trace/ftrace.txt

@@ -1873,7 +1873,7 @@ feature:
 
 	status\input  |     0      |     1      |    else    |
 	--------------+------------+------------+------------+
-	not allocated |(do nothing)| alloc+swap |   EINVAL   |
+	not allocated |(do nothing)| alloc+swap |(do nothing)|
 	--------------+------------+------------+------------+
 	allocated     |    free    |    swap    |   clear    |
 	--------------+------------+------------+------------+

MAINTAINERS

@@ -4005,6 +4005,22 @@ M:	Stanislaw Gruszka <stf_xl@wp.pl>
 S:	Maintained
 F:	drivers/usb/atm/ueagle-atm.c
 
+INA209 HARDWARE MONITOR DRIVER
+M:	Guenter Roeck <linux@roeck-us.net>
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+F:	Documentation/hwmon/ina209
+F:	Documentation/devicetree/bindings/i2c/ina209.txt
+F:	drivers/hwmon/ina209.c
+
+INA2XX HARDWARE MONITOR DRIVER
+M:	Guenter Roeck <linux@roeck-us.net>
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+F:	Documentation/hwmon/ina2xx
+F:	drivers/hwmon/ina2xx.c
+F:	include/linux/platform_data/ina2xx.h
+
 INDUSTRY PACK SUBSYSTEM (IPACK)
 M:	Samuel Iglesias Gonsalvez <siglesias@igalia.com>
 M:	Jens Taprogge <jens.taprogge@taprogge.org>
@@ -5098,6 +5114,15 @@ S:	Maintained
 F:	Documentation/hwmon/max6650
 F:	drivers/hwmon/max6650.c
 
+MAX6697 HARDWARE MONITOR DRIVER
+M:	Guenter Roeck <linux@roeck-us.net>
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+F:	Documentation/hwmon/max6697
+F:	Documentation/devicetree/bindings/i2c/max6697.txt
+F:	drivers/hwmon/max6697.c
+F:	include/linux/platform_data/max6697.h
+
 MAXIRADIO FM RADIO RECEIVER DRIVER
 M:	Hans Verkuil <hverkuil@xs4all.nl>
 L:	linux-media@vger.kernel.org
@@ -6412,6 +6437,8 @@ F:	Documentation/networking/LICENSE.qla3xxx
 F:	drivers/net/ethernet/qlogic/qla3xxx.*
 
 QLOGIC QLCNIC (1/10)Gb ETHERNET DRIVER
+M:	Rajesh Borundia <rajesh.borundia@qlogic.com>
+M:	Shahed Shaikh <shahed.shaikh@qlogic.com>
 M:	Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
 M:	Sony Chacko <sony.chacko@qlogic.com>
 M:	linux-driver@qlogic.com

Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 9
 SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc3
 NAME = Unicycling Gorilla
 
 # *DOCUMENTATION*

arch/Kconfig

@@ -319,13 +319,6 @@ config ARCH_WANT_OLD_COMPAT_IPC
 	select ARCH_WANT_COMPAT_IPC_PARSE_VERSION
 	bool
 
-config HAVE_VIRT_TO_BUS
-	bool
-	help
-	  An architecture should select this if it implements the
-	  deprecated interface virt_to_bus().  All new architectures
-	  should probably not select this.
-
 config HAVE_ARCH_SECCOMP_FILTER
 	bool
 	help

arch/alpha/Kconfig

@@ -9,7 +9,7 @@ config ALPHA
 	select HAVE_PERF_EVENTS
 	select HAVE_DMA_ATTRS
 	select HAVE_GENERIC_HARDIRQS
-	select HAVE_VIRT_TO_BUS
+	select VIRT_TO_BUS
 	select GENERIC_IRQ_PROBE
 	select AUTO_IRQ_AFFINITY if SMP
 	select GENERIC_IRQ_SHOW

arch/arm/Kconfig

@@ -49,7 +49,7 @@ config ARM
 	select HAVE_REGS_AND_STACK_ACCESS_API
 	select HAVE_SYSCALL_TRACEPOINTS
 	select HAVE_UID16
-	select HAVE_VIRT_TO_BUS
+	select VIRT_TO_BUS
 	select KTIME_SCALAR
 	select PERF_USE_VMALLOC
 	select RTC_LIB
@@ -556,7 +556,6 @@ config ARCH_IXP4XX
 config ARCH_DOVE
 	bool "Marvell Dove"
 	select ARCH_REQUIRE_GPIOLIB
-	select COMMON_CLK_DOVE
 	select CPU_V7
 	select GENERIC_CLOCKEVENTS
 	select MIGHT_HAVE_PCI
@@ -1658,13 +1657,16 @@ config LOCAL_TIMERS
 	  accounting to be spread across the timer interval, preventing a
 	  "thundering herd" at every timer tick.
 
+# The GPIO number here must be sorted by descending number. In case of
+# a multiplatform kernel, we just want the highest value required by the
+# selected platforms.
 config ARCH_NR_GPIO
 	int
 	default 1024 if ARCH_SHMOBILE || ARCH_TEGRA
-	default 355 if ARCH_U8500
-	default 264 if MACH_H4700
 	default 512 if SOC_OMAP5
+	default 355 if ARCH_U8500
 	default 288 if ARCH_VT8500 || ARCH_SUNXI
+	default 264 if MACH_H4700
 	default 0
 	help
 	  Maximum number of GPIOs in the system.
@@ -1888,8 +1890,9 @@ config XEN_DOM0
 
 config XEN
 	bool "Xen guest support on ARM (EXPERIMENTAL)"
-	depends on ARM && OF
+	depends on ARM && AEABI && OF
 	depends on CPU_V7 && !CPU_V6
+	depends on !GENERIC_ATOMIC64
 	help
 	  Say Y if you want to run Linux in a Virtual Machine on Xen on ARM.
 

arch/arm/Kconfig.debug

@@ -492,7 +492,7 @@ config DEBUG_IMX_UART_PORT
 						DEBUG_IMX31_UART || \
 						DEBUG_IMX35_UART || \
 						DEBUG_IMX51_UART || \
-						DEBUG_IMX50_IMX53_UART || \
+						DEBUG_IMX53_UART || \
 						DEBUG_IMX6Q_UART
 	default 1
 	help

arch/arm/boot/Makefile

@@ -115,4 +115,4 @@ i:
 	$(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \
 	$(obj)/Image System.map "$(INSTALL_PATH)"
 
-subdir-	    := bootp compressed
+subdir-	    := bootp compressed dts

arch/arm/boot/dts/armada-370-rd.dts

@@ -64,5 +64,13 @@
 			status = "okay";
 			/* No CD or WP GPIOs */
 		};
+
+		usb@d0050000 {
+			status = "okay";
+		};
+
+		usb@d0051000 {
+			status = "okay";
+		};
 	};
 };

arch/arm/boot/dts/armada-370-xp.dtsi

@@ -31,7 +31,6 @@
 	mpic: interrupt-controller@d0020000 {
 	      compatible = "marvell,mpic";
 	      #interrupt-cells = <1>;
-	      #address-cells = <1>;
 	      #size-cells = <1>;
 	      interrupt-controller;
 	};
@@ -54,7 +53,7 @@
 				reg = <0xd0012000 0x100>;
 				reg-shift = <2>;
 				interrupts = <41>;
-				reg-io-width = <4>;
+				reg-io-width = <1>;
 				status = "disabled";
 		};
 		serial@d0012100 {
@@ -62,7 +61,7 @@
 				reg = <0xd0012100 0x100>;
 				reg-shift = <2>;
 				interrupts = <42>;
-				reg-io-width = <4>;
+				reg-io-width = <1>;
 				status = "disabled";
 		};
 

arch/arm/boot/dts/armada-xp.dtsi

@@ -46,7 +46,7 @@
 				reg = <0xd0012200 0x100>;
 				reg-shift = <2>;
 				interrupts = <43>;
-				reg-io-width = <4>;
+				reg-io-width = <1>;
 				status = "disabled";
 		};
 		serial@d0012300 {
@@ -54,7 +54,7 @@
 				reg = <0xd0012300 0x100>;
 				reg-shift = <2>;
 				interrupts = <44>;
-				reg-io-width = <4>;
+				reg-io-width = <1>;
 				status = "disabled";
 		};
 

arch/arm/boot/dts/bcm2835.dtsi

@@ -105,7 +105,7 @@
 			compatible = "fixed-clock";
 			reg = <1>;
 			#clock-cells = <0>;
-			clock-frequency = <150000000>;
+			clock-frequency = <250000000>;
 		};
 	};
 };

arch/arm/boot/dts/dbx5x0.dtsi

@@ -319,9 +319,8 @@
 				};
 			};
 
-			ab8500@5 {
+			ab8500 {
 				compatible = "stericsson,ab8500";
-				reg = <5>; /* mailbox 5 is i2c */
 				interrupt-parent = <&intc>;
 				interrupts = <0 40 0x4>;
 				interrupt-controller;

arch/arm/boot/dts/dove.dtsi

@@ -197,6 +197,11 @@
 			status = "disabled";
 		};
 
+		rtc@d8500 {
+			compatible = "marvell,orion-rtc";
+			reg = <0xd8500 0x20>;
+		};
+
 		crypto: crypto@30000 {
 			compatible = "marvell,orion-crypto";
 			reg = <0x30000 0x10000>,

arch/arm/boot/dts/href.dtsi

@@ -221,7 +221,7 @@
 				};
 			};
 
-			ab8500@5 {
+			ab8500 {
 				ab8500-regulators {
 					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
 						regulator-name = "V-DISPLAY";

arch/arm/boot/dts/hrefv60plus.dts

@@ -158,7 +158,7 @@
 				};
 			};
 
-			ab8500@5 {
+			ab8500 {
 				ab8500-regulators {
 					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
 						regulator-name = "V-DISPLAY";

arch/arm/boot/dts/imx53-mba53.dts

@@ -42,10 +42,9 @@
 			fsl,pins = <689 0x10000		/* DISP1_DRDY	*/
 				    482 0x10000		/* DISP1_HSYNC	*/
 				    489 0x10000		/* DISP1_VSYNC	*/
-				    684 0x10000		/* DISP1_DAT_0	*/
 				    515 0x10000		/* DISP1_DAT_22	*/
 				    523 0x10000		/* DISP1_DAT_23	*/
-				    543 0x10000		/* DISP1_DAT_21	*/
+				    545 0x10000		/* DISP1_DAT_21	*/
 				    553 0x10000		/* DISP1_DAT_20	*/
 				    558 0x10000		/* DISP1_DAT_19	*/
 				    564 0x10000		/* DISP1_DAT_18	*/

arch/arm/boot/dts/kirkwood-dns320.dts

@@ -42,12 +42,10 @@
 
 	ocp@f1000000 {
 		serial@12000 {
-			clock-frequency = <166666667>;
 			status = "okay";
 		};
 
 		serial@12100 {
-			clock-frequency = <166666667>;
 			status = "okay";
 		};
 	};

arch/arm/boot/dts/kirkwood-dns325.dts

@@ -50,7 +50,6 @@
 			};
 		};
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "okay";
 		};
 	};

arch/arm/boot/dts/kirkwood-dockstar.dts

@@ -37,7 +37,6 @@
 			};
 		};
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 

arch/arm/boot/dts/kirkwood-dreamplug.dts

@@ -38,7 +38,6 @@
 			};
 		};
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 

arch/arm/boot/dts/kirkwood-goflexnet.dts

@@ -73,7 +73,6 @@
 			};
 		};
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 

arch/arm/boot/dts/kirkwood-ib62x0.dts

@@ -51,7 +51,6 @@
 			};
 		};
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "okay";
 		};
 

arch/arm/boot/dts/kirkwood-iconnect.dts

@@ -78,7 +78,6 @@
 			};
 		};
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 

arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts

@@ -115,7 +115,6 @@
 		};
 
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 

arch/arm/boot/dts/kirkwood-km_kirkwood.dts

@@ -34,7 +34,6 @@
 		};
 
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 

arch/arm/boot/dts/kirkwood-lschlv2.dts

@@ -13,7 +13,6 @@
 
 	ocp@f1000000 {
 		serial@12000 {
-			clock-frequency = <166666667>;
 			status = "okay";
 		};
 	};

arch/arm/boot/dts/kirkwood-lsxhl.dts

@@ -13,7 +13,6 @@
 
 	ocp@f1000000 {
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "okay";
 		};
 	};

arch/arm/boot/dts/kirkwood-mplcec4.dts

@@ -90,7 +90,6 @@
                 };
 
                 serial@12000 {
-                        clock-frequency = <200000000>;
                         status = "ok";
                 };
 

arch/arm/boot/dts/kirkwood-ns2-common.dtsi

@@ -23,7 +23,6 @@
 		};
 
 		serial@12000 {
-			clock-frequency = <166666667>;
 			status = "okay";
 		};
 

arch/arm/boot/dts/kirkwood-nsa310.dts

@@ -117,7 +117,6 @@
 		};
 
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 

arch/arm/boot/dts/kirkwood-openblocks_a6.dts

@@ -18,12 +18,10 @@
 
 	ocp@f1000000 {
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 
 		serial@12100 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 

arch/arm/boot/dts/kirkwood-topkick.dts

@@ -108,7 +108,6 @@
 		};
 
 		serial@12000 {
-			clock-frequency = <200000000>;
 			status = "ok";
 		};
 

arch/arm/boot/dts/kirkwood.dtsi

@@ -38,6 +38,7 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			interrupts = <35>, <36>, <37>, <38>;
+			clocks = <&gate_clk 7>;
 		};
 
 		gpio1: gpio@10140 {
@@ -49,6 +50,7 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			interrupts = <39>, <40>, <41>;
+			clocks = <&gate_clk 7>;
 		};
 
 		serial@12000 {
@@ -57,7 +59,6 @@
 			reg-shift = <2>;
 			interrupts = <33>;
 			clocks = <&gate_clk 7>;
-			/* set clock-frequency in board dts */
 			status = "disabled";
 		};
 
@@ -67,7 +68,6 @@
 			reg-shift = <2>;
 			interrupts = <34>;
 			clocks = <&gate_clk 7>;
-			/* set clock-frequency in board dts */
 			status = "disabled";
 		};
 
@@ -75,6 +75,7 @@
 			compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc";
 			reg = <0x10300 0x20>;
 			interrupts = <53>;
+			clocks = <&gate_clk 7>;
 		};
 
 		spi@10600 {

arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts

@@ -11,7 +11,7 @@
 
 / {
 	model = "LaCie Ethernet Disk mini V2";
-	compatible = "lacie,ethernet-disk-mini-v2", "marvell-orion5x-88f5182", "marvell,orion5x";
+	compatible = "lacie,ethernet-disk-mini-v2", "marvell,orion5x-88f5182", "marvell,orion5x";
 
 	memory {
 		reg = <0x00000000 0x4000000>; /* 64 MB */

arch/arm/boot/dts/snowball.dts

@@ -298,7 +298,7 @@
 				};
 			};
 
-			ab8500@5 {
+			ab8500 {
 				ab8500-regulators {
 					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
 						regulator-name = "V-DISPLAY";

arch/arm/boot/dts/socfpga.dtsi

@@ -75,6 +75,9 @@
 				compatible = "arm,pl330", "arm,primecell";
 				reg = <0xffe01000 0x1000>;
 				interrupts = <0 180 4>;
+				#dma-cells = <1>;
+				#dma-channels = <8>;
+				#dma-requests = <32>;
 			};
 		};
 

arch/arm/boot/dts/tegra20.dtsi

@@ -118,6 +118,7 @@
 		compatible = "arm,cortex-a9-twd-timer";
 		reg = <0x50040600 0x20>;
 		interrupts = <1 13 0x304>;
+		clocks = <&tegra_car 132>;
 	};
 
 	intc: interrupt-controller {

arch/arm/boot/dts/tegra30.dtsi

@@ -119,6 +119,7 @@
 		compatible = "arm,cortex-a9-twd-timer";
 		reg = <0x50040600 0x20>;
 		interrupts = <1 13 0xf04>;
+		clocks = <&tegra_car 214>;
 	};
 
 	intc: interrupt-controller {

arch/arm/configs/mxs_defconfig

@@ -116,6 +116,7 @@ CONFIG_SND_SOC=y
 CONFIG_SND_MXS_SOC=y
 CONFIG_SND_SOC_MXS_SGTL5000=y
 CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_CHIPIDEA=y
 CONFIG_USB_CHIPIDEA_HOST=y
 CONFIG_USB_STORAGE=y

arch/arm/configs/omap2plus_defconfig

@@ -126,6 +126,8 @@ CONFIG_INPUT_MISC=y
 CONFIG_INPUT_TWL4030_PWRBUTTON=y
 CONFIG_VT_HW_CONSOLE_BINDING=y
 # CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_8250_NR_UARTS=32
 CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_MANY_PORTS=y

arch/arm/include/asm/irq.h

@@ -30,6 +30,11 @@ extern void asm_do_IRQ(unsigned int, struct pt_regs *);
 void handle_IRQ(unsigned int, struct pt_regs *);
 void init_IRQ(void);
 
+#ifdef CONFIG_MULTI_IRQ_HANDLER
+extern void (*handle_arch_irq)(struct pt_regs *);
+extern void set_handle_irq(void (*handle_irq)(struct pt_regs *));
+#endif
+
 #endif
 
 #endif

arch/arm/include/asm/mach/irq.h

@@ -20,11 +20,6 @@ struct seq_file;
 extern void init_FIQ(int);
 extern int show_fiq_list(struct seq_file *, int);
 
-#ifdef CONFIG_MULTI_IRQ_HANDLER
-extern void (*handle_arch_irq)(struct pt_regs *);
-extern void set_handle_irq(void (*handle_irq)(struct pt_regs *));
-#endif
-
 /*
  * This is for easy migration, but should be changed in the source
  */
@@ -35,35 +30,4 @@ do {							\
 	raw_spin_unlock(&desc->lock);			\
 } while(0)
 
-#ifndef __ASSEMBLY__
-/*
- * Entry/exit functions for chained handlers where the primary IRQ chip
- * may implement either fasteoi or level-trigger flow control.
- */
-static inline void chained_irq_enter(struct irq_chip *chip,
-				     struct irq_desc *desc)
-{
-	/* FastEOI controllers require no action on entry. */
-	if (chip->irq_eoi)
-		return;
-
-	if (chip->irq_mask_ack) {
-		chip->irq_mask_ack(&desc->irq_data);
-	} else {
-		chip->irq_mask(&desc->irq_data);
-		if (chip->irq_ack)
-			chip->irq_ack(&desc->irq_data);
-	}
-}
-
-static inline void chained_irq_exit(struct irq_chip *chip,
-				    struct irq_desc *desc)
-{
-	if (chip->irq_eoi)
-		chip->irq_eoi(&desc->irq_data);
-	else
-		chip->irq_unmask(&desc->irq_data);
-}
-#endif
-
 #endif

arch/arm/include/asm/xen/events.h

@@ -2,6 +2,7 @@
 #define _ASM_ARM_XEN_EVENTS_H
 
 #include <asm/ptrace.h>
+#include <asm/atomic.h>
 
 enum ipi_vector {
 	XEN_PLACEHOLDER_VECTOR,
@@ -15,26 +16,8 @@ static inline int xen_irqs_disabled(struct pt_regs *regs)
 	return raw_irqs_disabled_flags(regs->ARM_cpsr);
 }
 
-/*
- * We cannot use xchg because it does not support 8-byte
- * values. However it is safe to use {ldr,dtd}exd directly because all
- * platforms which Xen can run on support those instructions.
- */
-static inline xen_ulong_t xchg_xen_ulong(xen_ulong_t *ptr, xen_ulong_t val)
-{
-	xen_ulong_t oldval;
-	unsigned int tmp;
-
-	wmb();
-	asm volatile("@ xchg_xen_ulong\n"
-		"1:     ldrexd  %0, %H0, [%3]\n"
-		"       strexd  %1, %2, %H2, [%3]\n"
-		"       teq     %1, #0\n"
-		"       bne     1b"
-		: "=&r" (oldval), "=&r" (tmp)
-		: "r" (val), "r" (ptr)
-		: "memory", "cc");
-	return oldval;
-}
+#define xchg_xen_ulong(ptr, val) atomic64_xchg(container_of((ptr),	\
+							    atomic64_t,	\
+							    counter), (val))
 
 #endif /* _ASM_ARM_XEN_EVENTS_H */

arch/arm/mach-at91/board-foxg20.c

@@ -176,6 +176,7 @@ static struct w1_gpio_platform_data w1_gpio_pdata = {
 	/* If you choose to use a pin other than PB16 it needs to be 3.3V */
 	.pin		= AT91_PIN_PB16,
 	.is_open_drain  = 1,
+	.ext_pullup_enable_pin	= -EINVAL,
 };
 
 static struct platform_device w1_device = {

arch/arm/mach-at91/board-stamp9g20.c

@@ -188,6 +188,7 @@ static struct spi_board_info portuxg20_spi_devices[] = {
 static struct w1_gpio_platform_data w1_gpio_pdata = {
 	.pin		= AT91_PIN_PA29,
 	.is_open_drain	= 1,
+	.ext_pullup_enable_pin	= -EINVAL,
 };
 
 static struct platform_device w1_device = {

arch/arm/mach-at91/gpio.c

@@ -22,10 +22,9 @@
 #include <linux/module.h>
 #include <linux/io.h>
 #include <linux/irqdomain.h>
+#include <linux/irqchip/chained_irq.h>
 #include <linux/of_address.h>
 
-#include <asm/mach/irq.h>
-
 #include <mach/hardware.h>
 #include <mach/at91_pio.h>
 

arch/arm/mach-exynos/common.c

@@ -26,6 +26,7 @@
 #include <linux/irqchip.h>
 #include <linux/of_address.h>
 #include <linux/irqchip/arm-gic.h>
+#include <linux/irqchip/chained_irq.h>
 
 #include <asm/proc-fns.h>
 #include <asm/exception.h>

arch/arm/mach-exynos/platsmp.c

@@ -20,7 +20,6 @@
 #include <linux/jiffies.h>
 #include <linux/smp.h>
 #include <linux/io.h>
-#include <linux/irqchip/arm-gic.h>
 
 #include <asm/cacheflush.h>
 #include <asm/smp_plat.h>
@@ -75,13 +74,6 @@ static DEFINE_SPINLOCK(boot_lock);
 
 static void __cpuinit exynos_secondary_init(unsigned int cpu)
 {
-	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
 	/*
 	 * let the primary processor know we're out of the
 	 * pen, then head off into the C entry point

arch/arm/mach-highbank/platsmp.c

@@ -17,7 +17,6 @@
 #include <linux/init.h>
 #include <linux/smp.h>
 #include <linux/io.h>
-#include <linux/irqchip/arm-gic.h>
 
 #include <asm/smp_scu.h>
 
@@ -25,11 +24,6 @@
 
 extern void secondary_startup(void);
 
-static void __cpuinit highbank_secondary_init(unsigned int cpu)
-{
-	gic_secondary_init(0);
-}
-
 static int __cpuinit highbank_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	highbank_set_cpu_jump(cpu, secondary_startup);
@@ -67,7 +61,6 @@ static void __init highbank_smp_prepare_cpus(unsigned int max_cpus)
 struct smp_operations highbank_smp_ops __initdata = {
 	.smp_init_cpus		= highbank_smp_init_cpus,
 	.smp_prepare_cpus	= highbank_smp_prepare_cpus,
-	.smp_secondary_init	= highbank_secondary_init,
 	.smp_boot_secondary	= highbank_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_die		= highbank_cpu_die,

arch/arm/mach-imx/clk-imx6q.c

@@ -172,7 +172,7 @@ static struct clk *clk[clk_max];
 static struct clk_onecell_data clk_data;
 
 static enum mx6q_clks const clks_init_on[] __initconst = {
-	mmdc_ch0_axi, rom,
+	mmdc_ch0_axi, rom, pll1_sys,
 };
 
 static struct clk_div_table clk_enet_ref_table[] = {

arch/arm/mach-imx/headsmp.S

@@ -26,16 +26,16 @@ ENDPROC(v7_secondary_startup)
 
 #ifdef CONFIG_PM
 /*
- * The following code is located into the .data section.  This is to
- * allow phys_l2x0_saved_regs to be accessed with a relative load
- * as we are running on physical address here.
+ * The following code must assume it is running from physical address
+ * where absolute virtual addresses to the data section have to be
+ * turned into relative ones.
  */
-	.data
-	.align
 
 #ifdef CONFIG_CACHE_L2X0
 	.macro	pl310_resume
-	ldr	r2, phys_l2x0_saved_regs
+	adr	r0, l2x0_saved_regs_offset
+	ldr	r2, [r0]
+	add	r2, r2, r0
 	ldr	r0, [r2, #L2X0_R_PHY_BASE]	@ get physical base of l2x0
 	ldr	r1, [r2, #L2X0_R_AUX_CTRL]	@ get aux_ctrl value
 	str	r1, [r0, #L2X0_AUX_CTRL]	@ restore aux_ctrl
@@ -43,9 +43,9 @@ ENDPROC(v7_secondary_startup)
 	str	r1, [r0, #L2X0_CTRL]		@ re-enable L2
 	.endm
 
-	.globl	phys_l2x0_saved_regs
-phys_l2x0_saved_regs:
-        .long   0
+l2x0_saved_regs_offset:
+	.word	l2x0_saved_regs - .
+
 #else
 	.macro	pl310_resume
 	.endm

arch/arm/mach-imx/platsmp.c

@@ -12,7 +12,6 @@
 
 #include <linux/init.h>
 #include <linux/smp.h>
-#include <linux/irqchip/arm-gic.h>
 #include <asm/page.h>
 #include <asm/smp_scu.h>
 #include <asm/mach/map.h>
@@ -52,16 +51,6 @@ void imx_scu_standby_enable(void)
 	writel_relaxed(val, scu_base);
 }
 
-static void __cpuinit imx_secondary_init(unsigned int cpu)
-{
-	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-}
-
 static int __cpuinit imx_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	imx_set_cpu_jump(cpu, v7_secondary_startup);
@@ -96,7 +85,6 @@ static void __init imx_smp_prepare_cpus(unsigned int max_cpus)
 struct smp_operations  imx_smp_ops __initdata = {
 	.smp_init_cpus		= imx_smp_init_cpus,
 	.smp_prepare_cpus	= imx_smp_prepare_cpus,
-	.smp_secondary_init	= imx_secondary_init,
 	.smp_boot_secondary	= imx_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_die		= imx_cpu_die,

arch/arm/mach-imx/pm-imx6q.c

@@ -22,8 +22,6 @@
 #include "common.h"
 #include "hardware.h"
 
-extern unsigned long phys_l2x0_saved_regs;
-
 static int imx6q_suspend_finish(unsigned long val)
 {
 	cpu_do_idle();
@@ -57,18 +55,5 @@ static const struct platform_suspend_ops imx6q_pm_ops = {
 
 void __init imx6q_pm_init(void)
 {
-	/*
-	 * The l2x0 core code provides an infrastucture to save and restore
-	 * l2x0 registers across suspend/resume cycle.  But because imx6q
-	 * retains L2 content during suspend and needs to resume L2 before
-	 * MMU is enabled, it can only utilize register saving support and
-	 * have to take care of restoring on its own.  So we save physical
-	 * address of the data structure used by l2x0 core to save registers,
-	 * and later restore the necessary ones in imx6q resume entry.
-	 */
-#ifdef CONFIG_CACHE_L2X0
-	phys_l2x0_saved_regs = __pa(&l2x0_saved_regs);
-#endif
-
 	suspend_set_ops(&imx6q_pm_ops);
 }

arch/arm/mach-ixp4xx/vulcan-setup.c

@@ -163,6 +163,7 @@ static struct platform_device vulcan_max6369 = {
 
 static struct w1_gpio_platform_data vulcan_w1_gpio_pdata = {
 	.pin			= 14,
+	.ext_pullup_enable_pin	= -EINVAL,
 };
 
 static struct platform_device vulcan_w1_gpio = {

arch/arm/mach-kirkwood/board-dt.c

@@ -41,16 +41,12 @@ static void __init kirkwood_legacy_clk_init(void)
 
 	struct device_node *np = of_find_compatible_node(
 		NULL, NULL, "marvell,kirkwood-gating-clock");
-
 	struct of_phandle_args clkspec;
+	struct clk *clk;
 
 	clkspec.np = np;
 	clkspec.args_count = 1;
 
-	clkspec.args[0] = CGC_BIT_GE0;
-	orion_clkdev_add(NULL, "mv643xx_eth_port.0",
-			 of_clk_get_from_provider(&clkspec));
-
 	clkspec.args[0] = CGC_BIT_PEX0;
 	orion_clkdev_add("0", "pcie",
 			 of_clk_get_from_provider(&clkspec));
@@ -59,9 +55,24 @@ static void __init kirkwood_legacy_clk_init(void)
 	orion_clkdev_add("1", "pcie",
 			 of_clk_get_from_provider(&clkspec));
 
-	clkspec.args[0] = CGC_BIT_GE1;
-	orion_clkdev_add(NULL, "mv643xx_eth_port.1",
+	clkspec.args[0] = CGC_BIT_SDIO;
+	orion_clkdev_add(NULL, "mvsdio",
 			 of_clk_get_from_provider(&clkspec));
+
+	/*
+	 * The ethernet interfaces forget the MAC address assigned by
+	 * u-boot if the clocks are turned off. Until proper DT support
+	 * is available we always enable them for now.
+	 */
+	clkspec.args[0] = CGC_BIT_GE0;
+	clk = of_clk_get_from_provider(&clkspec);
+	orion_clkdev_add(NULL, "mv643xx_eth_port.0", clk);
+	clk_prepare_enable(clk);
+
+	clkspec.args[0] = CGC_BIT_GE1;
+	clk = of_clk_get_from_provider(&clkspec);
+	orion_clkdev_add(NULL, "mv643xx_eth_port.1", clk);
+	clk_prepare_enable(clk);
 }
 
 static void __init kirkwood_of_clk_init(void)

arch/arm/mach-msm/platsmp.c

@@ -15,7 +15,6 @@
 #include <linux/jiffies.h>
 #include <linux/smp.h>
 #include <linux/io.h>
-#include <linux/irqchip/arm-gic.h>
 
 #include <asm/cacheflush.h>
 #include <asm/cputype.h>
@@ -41,13 +40,6 @@ static inline int get_core_count(void)
 
 static void __cpuinit msm_secondary_init(unsigned int cpu)
 {
-	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
 	/*
 	 * let the primary processor know we're out of the
 	 * pen, then head off into the C entry point

arch/arm/mach-mxs/icoll.c

@@ -100,7 +100,7 @@ static struct irq_domain_ops icoll_irq_domain_ops = {
 	.xlate = irq_domain_xlate_onecell,
 };
 
-void __init icoll_of_init(struct device_node *np,
+static void __init icoll_of_init(struct device_node *np,
 			  struct device_node *interrupt_parent)
 {
 	/*

arch/arm/mach-mxs/mach-mxs.c

@@ -402,17 +402,17 @@ static void __init cfa10049_init(void)
 {
 	enable_clk_enet_out();
 	update_fec_mac_prop(OUI_CRYSTALFONTZ);
+
+	mxsfb_pdata.mode_list = cfa10049_video_modes;
+	mxsfb_pdata.mode_count = ARRAY_SIZE(cfa10049_video_modes);
+	mxsfb_pdata.default_bpp = 32;
+	mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT;
 }
 
 static void __init cfa10037_init(void)
 {
 	enable_clk_enet_out();
 	update_fec_mac_prop(OUI_CRYSTALFONTZ);
-
-	mxsfb_pdata.mode_list = cfa10049_video_modes;
-	mxsfb_pdata.mode_count = ARRAY_SIZE(cfa10049_video_modes);
-	mxsfb_pdata.default_bpp = 32;
-	mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT;
 }
 
 static void __init apf28_init(void)

arch/arm/mach-mxs/mm.c

@@ -18,6 +18,7 @@
 
 #include <mach/mx23.h>
 #include <mach/mx28.h>
+#include <mach/common.h>
 
 /*
  * Define the MX23 memory map.

arch/arm/mach-mxs/ocotp.c

@@ -19,6 +19,7 @@
 #include <asm/processor.h>	/* for cpu_relax() */
 
 #include <mach/mxs.h>
+#include <mach/common.h>
 
 #define OCOTP_WORD_OFFSET		0x20
 #define OCOTP_WORD_COUNT		0x20

arch/arm/mach-omap1/common.h

@@ -31,6 +31,8 @@
 
 #include <plat/i2c.h>
 
+#include <mach/irqs.h>
+
 #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
 void omap7xx_map_io(void);
 #else

arch/arm/mach-omap2/Kconfig

@@ -311,9 +311,6 @@ config MACH_OMAP_ZOOM2
 	default y
 	select OMAP_PACKAGE_CBB
 	select REGULATOR_FIXED_VOLTAGE if REGULATOR
-	select SERIAL_8250
-	select SERIAL_8250_CONSOLE
-	select SERIAL_CORE_CONSOLE
 
 config MACH_OMAP_ZOOM3
 	bool "OMAP3630 Zoom3 board"
@@ -321,9 +318,6 @@ config MACH_OMAP_ZOOM3
 	default y
 	select OMAP_PACKAGE_CBP
 	select REGULATOR_FIXED_VOLTAGE if REGULATOR
-	select SERIAL_8250
-	select SERIAL_8250_CONSOLE
-	select SERIAL_CORE_CONSOLE
 
 config MACH_CM_T35
 	bool "CompuLab CM-T35/CM-T3730 modules"

arch/arm/mach-omap2/board-generic.c

@@ -102,6 +102,7 @@ DT_MACHINE_START(OMAP3_DT, "Generic OMAP3 (Flattened Device Tree)")
 	.init_irq	= omap_intc_of_init,
 	.handle_irq	= omap3_intc_handle_irq,
 	.init_machine	= omap_generic_init,
+	.init_late	= omap3_init_late,
 	.init_time	= omap3_sync32k_timer_init,
 	.dt_compat	= omap3_boards_compat,
 	.restart	= omap3xxx_restart,
@@ -119,6 +120,7 @@ DT_MACHINE_START(OMAP3_GP_DT, "Generic OMAP3-GP (Flattened Device Tree)")
 	.init_irq	= omap_intc_of_init,
 	.handle_irq	= omap3_intc_handle_irq,
 	.init_machine	= omap_generic_init,
+	.init_late	= omap3_init_late,
 	.init_time	= omap3_secure_sync32k_timer_init,
 	.dt_compat	= omap3_gp_boards_compat,
 	.restart	= omap3xxx_restart,

arch/arm/mach-omap2/board-rx51.c

@@ -17,6 +17,7 @@
 #include <linux/io.h>
 #include <linux/gpio.h>
 #include <linux/leds.h>
+#include <linux/usb/phy.h>
 #include <linux/usb/musb.h>
 #include <linux/platform_data/spi-omap2-mcspi.h>
 
@@ -98,6 +99,7 @@ static void __init rx51_init(void)
 	sdrc_params = nokia_get_sdram_timings();
 	omap_sdrc_init(sdrc_params, sdrc_params);
 
+	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
 	usb_musb_init(&musb_board_data);
 	rx51_peripherals_init();
 

arch/arm/mach-omap2/common.h

@@ -108,7 +108,6 @@ void omap35xx_init_late(void);
 void omap3630_init_late(void);
 void am35xx_init_late(void);
 void ti81xx_init_late(void);
-void omap4430_init_late(void);
 int omap2_common_pm_late_init(void);
 
 #if defined(CONFIG_SOC_OMAP2420) || defined(CONFIG_SOC_OMAP2430)

arch/arm/mach-omap2/gpmc.c

@@ -1122,9 +1122,6 @@ int gpmc_calc_timings(struct gpmc_timings *gpmc_t,
 	/* TODO: remove, see function definition */
 	gpmc_convert_ps_to_ns(gpmc_t);
 
-	/* Now the GPMC is initialised, unreserve the chip-selects */
-	gpmc_cs_map = 0;
-
 	return 0;
 }
 
@@ -1383,6 +1380,9 @@ static int gpmc_probe(struct platform_device *pdev)
 	if (IS_ERR_VALUE(gpmc_setup_irq()))
 		dev_warn(gpmc_dev, "gpmc_setup_irq failed\n");
 
+	/* Now the GPMC is initialised, unreserve the chip-selects */
+	gpmc_cs_map = 0;
+
 	rc = gpmc_probe_dt(pdev);
 	if (rc < 0) {
 		clk_disable_unprepare(gpmc_l3_clk);

arch/arm/mach-omap2/mux.c

@@ -211,8 +211,6 @@ static int __init _omap_mux_get_by_name(struct omap_mux_partition *partition,
 		return -EINVAL;
 	}
 
-	pr_err("%s: Could not find signal %s\n", __func__, muxname);
-
 	return -ENODEV;
 }
 
@@ -234,6 +232,8 @@ int __init omap_mux_get_by_name(const char *muxname,
 		return mux_mode;
 	}
 
+	pr_err("%s: Could not find signal %s\n", __func__, muxname);
+
 	return -ENODEV;
 }
 
@@ -739,8 +739,9 @@ static void __init omap_mux_dbg_create_entry(
 	list_for_each_entry(e, &partition->muxmodes, node) {
 		struct omap_mux *m = &e->mux;
 
-		(void)debugfs_create_file(m->muxnames[0], S_IWUSR, mux_dbg_dir,
-					  m, &omap_mux_dbg_signal_fops);
+		(void)debugfs_create_file(m->muxnames[0], S_IWUSR | S_IRUGO,
+					  mux_dbg_dir, m,
+					  &omap_mux_dbg_signal_fops);
 	}
 }
 

arch/arm/mach-omap2/omap-smp.c

@@ -66,13 +66,6 @@ static void __cpuinit omap4_secondary_init(unsigned int cpu)
 		omap_secure_dispatcher(OMAP4_PPA_CPU_ACTRL_SMP_INDEX,
 							4, 0, 0, 0, 0, 0);
 
-	/*
-	 * If any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
 	/*
 	 * Synchronise with the boot thread.
 	 */

arch/arm/mach-prima2/platsmp.c

@@ -11,7 +11,6 @@
 #include <linux/delay.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
-#include <linux/irqchip/arm-gic.h>
 #include <asm/page.h>
 #include <asm/mach/map.h>
 #include <asm/smp_plat.h>
@@ -48,13 +47,6 @@ void __init sirfsoc_map_scu(void)
 
 static void __cpuinit sirfsoc_secondary_init(unsigned int cpu)
 {
-	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
 	/*
 	 * let the primary processor know we're out of the
 	 * pen, then head off into the C entry point

arch/arm/mach-pxa/raumfeld.c

@@ -505,6 +505,7 @@ static struct w1_gpio_platform_data w1_gpio_platform_data = {
 	.pin			= GPIO_ONE_WIRE,
 	.is_open_drain		= 0,
 	.enable_external_pullup	= w1_enable_external_pullup,
+	.ext_pullup_enable_pin	= -EINVAL,
 };
 
 struct platform_device raumfeld_w1_gpio_device = {

arch/arm/mach-s3c24xx/irq.c

@@ -25,6 +25,7 @@
 #include <linux/ioport.h>
 #include <linux/device.h>
 #include <linux/irqdomain.h>
+#include <linux/irqchip/chained_irq.h>
 
 #include <asm/mach/irq.h>
 

arch/arm/mach-shmobile/smp-emev2.c

@@ -23,7 +23,6 @@
 #include <linux/spinlock.h>
 #include <linux/io.h>
 #include <linux/delay.h>
-#include <linux/irqchip/arm-gic.h>
 #include <mach/common.h>
 #include <mach/emev2.h>
 #include <asm/smp_plat.h>
@@ -85,11 +84,6 @@ static int __maybe_unused emev2_cpu_kill(unsigned int cpu)
 }
 
 
-static void __cpuinit emev2_secondary_init(unsigned int cpu)
-{
-	gic_secondary_init(0);
-}
-
 static int __cpuinit emev2_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	cpu = cpu_logical_map(cpu);
@@ -124,7 +118,6 @@ static void __init emev2_smp_init_cpus(void)
 struct smp_operations emev2_smp_ops __initdata = {
 	.smp_init_cpus		= emev2_smp_init_cpus,
 	.smp_prepare_cpus	= emev2_smp_prepare_cpus,
-	.smp_secondary_init	= emev2_secondary_init,
 	.smp_boot_secondary	= emev2_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_kill		= emev2_cpu_kill,

arch/arm/mach-shmobile/smp-r8a7779.c

@@ -23,7 +23,6 @@
 #include <linux/spinlock.h>
 #include <linux/io.h>
 #include <linux/delay.h>
-#include <linux/irqchip/arm-gic.h>
 #include <mach/common.h>
 #include <mach/r8a7779.h>
 #include <asm/smp_plat.h>
@@ -132,11 +131,6 @@ static int __maybe_unused r8a7779_cpu_kill(unsigned int cpu)
 }
 
 
-static void __cpuinit r8a7779_secondary_init(unsigned int cpu)
-{
-	gic_secondary_init(0);
-}
-
 static int __cpuinit r8a7779_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	struct r8a7779_pm_ch *ch = NULL;
@@ -186,7 +180,6 @@ static void __init r8a7779_smp_init_cpus(void)
 struct smp_operations r8a7779_smp_ops  __initdata = {
 	.smp_init_cpus		= r8a7779_smp_init_cpus,
 	.smp_prepare_cpus	= r8a7779_smp_prepare_cpus,
-	.smp_secondary_init	= r8a7779_secondary_init,
 	.smp_boot_secondary	= r8a7779_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_kill		= r8a7779_cpu_kill,

arch/arm/mach-shmobile/smp-sh73a0.c

@@ -23,7 +23,6 @@
 #include <linux/spinlock.h>
 #include <linux/io.h>
 #include <linux/delay.h>
-#include <linux/irqchip/arm-gic.h>
 #include <mach/common.h>
 #include <asm/cacheflush.h>
 #include <asm/smp_plat.h>
@@ -59,11 +58,6 @@ static unsigned int __init sh73a0_get_core_count(void)
 	return scu_get_core_count(scu_base);
 }
 
-static void __cpuinit sh73a0_secondary_init(unsigned int cpu)
-{
-	gic_secondary_init(0);
-}
-
 static int __cpuinit sh73a0_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	cpu = cpu_logical_map(cpu);
@@ -138,7 +132,6 @@ static void sh73a0_cpu_die(unsigned int cpu)
 struct smp_operations sh73a0_smp_ops __initdata = {
 	.smp_init_cpus		= sh73a0_smp_init_cpus,
 	.smp_prepare_cpus	= sh73a0_smp_prepare_cpus,
-	.smp_secondary_init	= sh73a0_secondary_init,
 	.smp_boot_secondary	= sh73a0_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_kill		= sh73a0_cpu_kill,

arch/arm/mach-socfpga/platsmp.c

@@ -22,7 +22,6 @@
 #include <linux/io.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
-#include <linux/irqchip/arm-gic.h>
 
 #include <asm/cacheflush.h>
 #include <asm/smp_scu.h>
@@ -33,16 +32,6 @@
 extern void __iomem *sys_manager_base_addr;
 extern void __iomem *rst_manager_base_addr;
 
-static void __cpuinit socfpga_secondary_init(unsigned int cpu)
-{
-	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-}
-
 static int __cpuinit socfpga_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	int trampoline_size = &secondary_trampoline_end - &secondary_trampoline;
@@ -109,7 +98,6 @@ static void socfpga_cpu_die(unsigned int cpu)
 struct smp_operations socfpga_smp_ops __initdata = {
 	.smp_init_cpus		= socfpga_smp_init_cpus,
 	.smp_prepare_cpus	= socfpga_smp_prepare_cpus,
-	.smp_secondary_init	= socfpga_secondary_init,
 	.smp_boot_secondary	= socfpga_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_die		= socfpga_cpu_die,

arch/arm/mach-spear13xx/platsmp.c

@@ -15,7 +15,6 @@
 #include <linux/jiffies.h>
 #include <linux/io.h>
 #include <linux/smp.h>
-#include <linux/irqchip/arm-gic.h>
 #include <asm/cacheflush.h>
 #include <asm/smp_scu.h>
 #include <mach/spear.h>
@@ -27,13 +26,6 @@ static void __iomem *scu_base = IOMEM(VA_SCU_BASE);
 
 static void __cpuinit spear13xx_secondary_init(unsigned int cpu)
 {
-	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
 	/*
 	 * let the primary processor know we're out of the
 	 * pen, then head off into the C entry point

arch/arm/mach-spear3xx/spear3xx.c

@@ -14,7 +14,7 @@
 #define pr_fmt(fmt) "SPEAr3xx: " fmt
 
 #include <linux/amba/pl022.h>
-#include <linux/amba/pl08x.h>
+#include <linux/amba/pl080.h>
 #include <linux/io.h>
 #include <plat/pl080.h>
 #include <mach/generic.h>

arch/arm/mach-tegra/platsmp.c

@@ -18,7 +18,6 @@
 #include <linux/jiffies.h>
 #include <linux/smp.h>
 #include <linux/io.h>
-#include <linux/irqchip/arm-gic.h>
 #include <linux/clk/tegra.h>
 
 #include <asm/cacheflush.h>
@@ -44,13 +43,6 @@ static cpumask_t tegra_cpu_init_mask;
 
 static void __cpuinit tegra_secondary_init(unsigned int cpu)
 {
-	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
 	cpumask_set_cpu(cpu, &tegra_cpu_init_mask);
 }
 

arch/arm/mach-ux500/platsmp.c

@@ -16,7 +16,6 @@
 #include <linux/device.h>
 #include <linux/smp.h>
 #include <linux/io.h>
-#include <linux/irqchip/arm-gic.h>
 
 #include <asm/cacheflush.h>
 #include <asm/smp_plat.h>
@@ -57,13 +56,6 @@ static DEFINE_SPINLOCK(boot_lock);
 
 static void __cpuinit ux500_secondary_init(unsigned int cpu)
 {
-	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
 	/*
 	 * let the primary processor know we're out of the
 	 * pen, then head off into the C entry point

arch/arm/mach-virt/platsmp.c

@@ -21,8 +21,6 @@
 #include <linux/smp.h>
 #include <linux/of.h>
 
-#include <linux/irqchip/arm-gic.h>
-
 #include <asm/psci.h>
 #include <asm/smp_plat.h>
 
@@ -45,14 +43,8 @@ static int __cpuinit virt_boot_secondary(unsigned int cpu,
 	return -ENODEV;
 }
 
-static void __cpuinit virt_secondary_init(unsigned int cpu)
-{
-	gic_secondary_init(0);
-}
-
 struct smp_operations __initdata virt_smp_ops = {
 	.smp_init_cpus		= virt_smp_init_cpus,
 	.smp_prepare_cpus	= virt_smp_prepare_cpus,
-	.smp_secondary_init	= virt_secondary_init,
 	.smp_boot_secondary	= virt_boot_secondary,
 };

arch/arm/mm/dma-mapping.c

@@ -342,6 +342,7 @@ static int __init atomic_pool_init(void)
 {
 	struct dma_pool *pool = &atomic_pool;
 	pgprot_t prot = pgprot_dmacoherent(pgprot_kernel);
+	gfp_t gfp = GFP_KERNEL | GFP_DMA;
 	unsigned long nr_pages = pool->size >> PAGE_SHIFT;
 	unsigned long *bitmap;
 	struct page *page;
@@ -361,8 +362,8 @@ static int __init atomic_pool_init(void)
 		ptr = __alloc_from_contiguous(NULL, pool->size, prot, &page,
 					      atomic_pool_init);
 	else
-		ptr = __alloc_remap_buffer(NULL, pool->size, GFP_KERNEL, prot,
-					   &page, atomic_pool_init);
+		ptr = __alloc_remap_buffer(NULL, pool->size, gfp, prot, &page,
+					   atomic_pool_init);
 	if (ptr) {
 		int i;
 

arch/arm/plat-orion/addr-map.c

@@ -157,9 +157,12 @@ void __init orion_setup_cpu_mbus_target(const struct orion_addr_map_cfg *cfg,
 		u32 size = readl(ddr_window_cpu_base + DDR_SIZE_CS_OFF(i));
 
 		/*
-		 * Chip select enabled?
+		 * We only take care of entries for which the chip
+		 * select is enabled, and that don't have high base
+		 * address bits set (devices can only access the first
+		 * 32 bits of the memory).
 		 */
-		if (size & 1) {
+		if ((size & 1) && !(base & 0xF)) {
 			struct mbus_dram_window *w;
 
 			w = &orion_mbus_dram_info.cs[cs++];

arch/arm/plat-samsung/irq-vic-timer.c

@@ -16,6 +16,7 @@
 #include <linux/kernel.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
+#include <linux/irqchip/chained_irq.h>
 #include <linux/io.h>
 
 #include <mach/map.h>
@@ -23,8 +24,6 @@
 #include <plat/irq-vic-timer.h>
 #include <plat/regs-timer.h>
 
-#include <asm/mach/irq.h>
-
 static void s3c_irq_demux_vic_timer(unsigned int irq, struct irq_desc *desc)
 {
 	struct irq_chip *chip = irq_get_chip(irq);

arch/arm/plat-samsung/s5p-irq-gpioint.c

@@ -14,6 +14,7 @@
 #include <linux/kernel.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
+#include <linux/irqchip/chained_irq.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
 #include <linux/slab.h>
@@ -22,8 +23,6 @@
 #include <plat/gpio-core.h>
 #include <plat/gpio-cfg.h>
 
-#include <asm/mach/irq.h>
-
 #define GPIO_BASE(chip)		((void __iomem *)((unsigned long)((chip)->base) & 0xFFFFF000u))
 
 #define CON_OFFSET		0x700

arch/arm/plat-spear/Kconfig

@@ -10,7 +10,7 @@ choice
 
 config ARCH_SPEAR13XX
 	bool "ST SPEAr13xx with Device Tree"
-	select ARCH_HAVE_CPUFREQ
+	select ARCH_HAS_CPUFREQ
 	select ARM_GIC
 	select CPU_V7
 	select GPIO_SPEAR_SPICS

arch/arm/plat-versatile/platsmp.c

@@ -14,7 +14,6 @@
 #include <linux/device.h>
 #include <linux/jiffies.h>
 #include <linux/smp.h>
-#include <linux/irqchip/arm-gic.h>
 
 #include <asm/cacheflush.h>
 #include <asm/smp_plat.h>
@@ -36,13 +35,6 @@ static DEFINE_SPINLOCK(boot_lock);
 
 void __cpuinit versatile_secondary_init(unsigned int cpu)
 {
-	/*
-	 * if any interrupts are already enabled for the primary
-	 * core (e.g. timer irq), then they will not have been enabled
-	 * for us: do so
-	 */
-	gic_secondary_init(0);
-
 	/*
 	 * let the primary processor know we're out of the
 	 * pen, then head off into the C entry point

arch/avr32/Kconfig

@@ -7,7 +7,7 @@ config AVR32
 	select HAVE_OPROFILE
 	select HAVE_KPROBES
 	select HAVE_GENERIC_HARDIRQS
-	select HAVE_VIRT_TO_BUS
+	select VIRT_TO_BUS
 	select GENERIC_IRQ_PROBE
 	select GENERIC_ATOMIC64
 	select HARDIRQS_SW_RESEND

arch/blackfin/Kconfig

@@ -33,7 +33,7 @@ config BLACKFIN
 	select ARCH_HAVE_CUSTOM_GPIO_H
 	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select HAVE_UID16
-	select HAVE_VIRT_TO_BUS
+	select VIRT_TO_BUS
 	select ARCH_WANT_IPC_PARSE_VERSION
 	select HAVE_GENERIC_HARDIRQS
 	select GENERIC_ATOMIC64

arch/cris/Kconfig

@@ -43,7 +43,7 @@ config CRIS
 	select GENERIC_ATOMIC64
 	select HAVE_GENERIC_HARDIRQS
 	select HAVE_UID16
-	select HAVE_VIRT_TO_BUS
+	select VIRT_TO_BUS
 	select ARCH_WANT_IPC_PARSE_VERSION
 	select GENERIC_IRQ_SHOW
 	select GENERIC_IOMAP

arch/frv/Kconfig

@@ -6,7 +6,7 @@ config FRV
 	select HAVE_PERF_EVENTS
 	select HAVE_UID16
 	select HAVE_GENERIC_HARDIRQS
-	select HAVE_VIRT_TO_BUS
+	select VIRT_TO_BUS
 	select GENERIC_IRQ_SHOW
 	select HAVE_DEBUG_BUGVERBOSE
 	select ARCH_HAVE_NMI_SAFE_CMPXCHG

arch/h8300/Kconfig

@@ -5,7 +5,7 @@ config H8300
 	select HAVE_GENERIC_HARDIRQS
 	select GENERIC_ATOMIC64
 	select HAVE_UID16
-	select HAVE_VIRT_TO_BUS
+	select VIRT_TO_BUS
 	select ARCH_WANT_IPC_PARSE_VERSION
 	select GENERIC_IRQ_SHOW
 	select GENERIC_CPU_DEVICES

arch/ia64/Kconfig

@@ -26,7 +26,7 @@ config IA64
 	select HAVE_MEMBLOCK
 	select HAVE_MEMBLOCK_NODE_MAP
 	select HAVE_VIRT_CPU_ACCOUNTING
-	select HAVE_VIRT_TO_BUS
+	select VIRT_TO_BUS
 	select ARCH_DISCARD_MEMBLOCK
 	select GENERIC_IRQ_PROBE
 	select GENERIC_PENDING_IRQ if SMP

arch/m32r/Kconfig

@@ -10,7 +10,7 @@ config M32R
 	select ARCH_WANT_IPC_PARSE_VERSION
 	select HAVE_DEBUG_BUGVERBOSE
 	select HAVE_GENERIC_HARDIRQS
-	select HAVE_VIRT_TO_BUS
+	select VIRT_TO_BUS
 	select GENERIC_IRQ_PROBE
 	select GENERIC_IRQ_SHOW
 	select GENERIC_ATOMIC64

arch/m32r/include/uapi/asm/stat.h

@@ -63,10 +63,10 @@ struct stat64 {
 	long long	st_size;
 	unsigned long	st_blksize;
 
-#if defined(__BIG_ENDIAN)
+#if defined(__BYTE_ORDER) ? __BYTE_ORDER == __BIG_ENDIAN : defined(__BIG_ENDIAN)
 	unsigned long	__pad4;		/* future possible st_blocks high bits */
 	unsigned long	st_blocks;	/* Number 512-byte blocks allocated. */
-#elif defined(__LITTLE_ENDIAN)
+#elif defined(__BYTE_ORDER) ? __BYTE_ORDER == __LITTLE_ENDIAN : defined(__LITTLE_ENDIAN)
 	unsigned long	st_blocks;	/* Number 512-byte blocks allocated. */
 	unsigned long	__pad4;		/* future possible st_blocks high bits */
 #else

arch/m68k/Kconfig

@@ -8,7 +8,7 @@ config M68K
 	select GENERIC_IRQ_SHOW
 	select GENERIC_ATOMIC64
 	select HAVE_UID16
-	select HAVE_VIRT_TO_BUS
+	select VIRT_TO_BUS
 	select ARCH_HAVE_NMI_SAFE_CMPXCHG if RMW_INSNS
 	select GENERIC_CPU_DEVICES
 	select GENERIC_STRNCPY_FROM_USER if MMU