diff --git a/arch/arm/mach-s3c2410/include/mach/spi.h b/arch/arm/mach-s3c2410/include/mach/spi.h index 193b39d654ed..4d9588373aa5 100644 --- a/arch/arm/mach-s3c2410/include/mach/spi.h +++ b/arch/arm/mach-s3c2410/include/mach/spi.h @@ -18,6 +18,8 @@ struct s3c2410_spi_info { unsigned int num_cs; /* total chipselects */ int bus_num; /* bus number to use. */ + unsigned int use_fiq:1; /* use fiq */ + void (*gpio_setup)(struct s3c2410_spi_info *spi, int enable); void (*set_cs)(struct s3c2410_spi_info *spi, int cs, int pol); }; diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 2d9d70359360..f55eb0107336 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -216,6 +216,17 @@ config SPI_S3C24XX help SPI driver for Samsung S3C24XX series ARM SoCs +config SPI_S3C24XX_FIQ + bool "S3C24XX driver with FIQ pseudo-DMA" + depends on SPI_S3C24XX + select FIQ + help + Enable FIQ support for the S3C24XX SPI driver to provide pseudo + DMA by using the fast-interrupt request framework, This allows + the driver to get DMA-like performance when there are either + no free DMA channels, or when doing transfers that required both + TX and RX data paths. + config SPI_S3C24XX_GPIO tristate "Samsung S3C24XX series SPI by GPIO" depends on ARCH_S3C2410 && EXPERIMENTAL @@ -226,6 +237,13 @@ config SPI_S3C24XX_GPIO the inbuilt hardware cannot provide the transfer mode, or where the board is using non hardware connected pins. +config SPI_S3C64XX + tristate "Samsung S3C64XX series type SPI" + depends on ARCH_S3C64XX && EXPERIMENTAL + select S3C64XX_DMA + help + SPI driver for Samsung S3C64XX and newer SoCs. + config SPI_SH_MSIOF tristate "SuperH MSIOF SPI controller" depends on SUPERH && HAVE_CLK @@ -289,6 +307,16 @@ config SPI_NUC900 # Add new SPI master controllers in alphabetical order above this line # +config SPI_DESIGNWARE + bool "DesignWare SPI controller core support" + depends on SPI_MASTER + help + general driver for SPI controller core from DesignWare + +config SPI_DW_PCI + tristate "PCI interface driver for DW SPI core" + depends on SPI_DESIGNWARE && PCI + # # There are lots of SPI device types, with sensors and memory # being probably the most widely used ones. diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index ed8c1675b52f..f3d2810ba11c 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -16,6 +16,8 @@ obj-$(CONFIG_SPI_BFIN) += spi_bfin5xx.o obj-$(CONFIG_SPI_BITBANG) += spi_bitbang.o obj-$(CONFIG_SPI_AU1550) += au1550_spi.o obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o +obj-$(CONFIG_SPI_DESIGNWARE) += dw_spi.o +obj-$(CONFIG_SPI_DW_PCI) += dw_spi_pci.o obj-$(CONFIG_SPI_GPIO) += spi_gpio.o obj-$(CONFIG_SPI_IMX) += spi_imx.o obj-$(CONFIG_SPI_LM70_LLP) += spi_lm70llp.o @@ -30,7 +32,8 @@ obj-$(CONFIG_SPI_MPC52xx) += mpc52xx_spi.o obj-$(CONFIG_SPI_MPC8xxx) += spi_mpc8xxx.o obj-$(CONFIG_SPI_PPC4xx) += spi_ppc4xx.o obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o -obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx.o +obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx_hw.o +obj-$(CONFIG_SPI_S3C64XX) += spi_s3c64xx.o obj-$(CONFIG_SPI_TXX9) += spi_txx9.o obj-$(CONFIG_SPI_XILINX) += xilinx_spi.o obj-$(CONFIG_SPI_XILINX_OF) += xilinx_spi_of.o @@ -39,6 +42,11 @@ obj-$(CONFIG_SPI_SH_SCI) += spi_sh_sci.o obj-$(CONFIG_SPI_SH_MSIOF) += spi_sh_msiof.o obj-$(CONFIG_SPI_STMP3XXX) += spi_stmp.o obj-$(CONFIG_SPI_NUC900) += spi_nuc900.o + +# special build for s3c24xx spi driver with fiq support +spi_s3c24xx_hw-y := spi_s3c24xx.o +spi_s3c24xx_hw-$(CONFIG_SPI_S3C24XX_FIQ) += spi_s3c24xx_fiq.o + # ... add above this line ... # SPI protocol drivers (device/link on bus) diff --git a/drivers/spi/atmel_spi.c b/drivers/spi/atmel_spi.c index f5b3fdbb1e27..d21c24eaf0a9 100644 --- a/drivers/spi/atmel_spi.c +++ b/drivers/spi/atmel_spi.c @@ -189,14 +189,14 @@ static void atmel_spi_next_xfer_data(struct spi_master *master, /* use scratch buffer only when rx or tx data is unspecified */ if (xfer->rx_buf) - *rx_dma = xfer->rx_dma + xfer->len - len; + *rx_dma = xfer->rx_dma + xfer->len - *plen; else { *rx_dma = as->buffer_dma; if (len > BUFFER_SIZE) len = BUFFER_SIZE; } if (xfer->tx_buf) - *tx_dma = xfer->tx_dma + xfer->len - len; + *tx_dma = xfer->tx_dma + xfer->len - *plen; else { *tx_dma = as->buffer_dma; if (len > BUFFER_SIZE) @@ -788,7 +788,7 @@ static int __init atmel_spi_probe(struct platform_device *pdev) spin_lock_init(&as->lock); INIT_LIST_HEAD(&as->queue); as->pdev = pdev; - as->regs = ioremap(regs->start, (regs->end - regs->start) + 1); + as->regs = ioremap(regs->start, resource_size(regs)); if (!as->regs) goto out_free_buffer; as->irq = irq; diff --git a/drivers/spi/dw_spi.c b/drivers/spi/dw_spi.c new file mode 100644 index 000000000000..31620fae77be --- /dev/null +++ b/drivers/spi/dw_spi.c @@ -0,0 +1,944 @@ +/* + * dw_spi.c - Designware SPI core controller driver (refer pxa2xx_spi.c) + * + * Copyright (c) 2009, Intel Corporation. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + */ + +#include +#include +#include +#include + +#include +#include + +#ifdef CONFIG_DEBUG_FS +#include +#endif + +#define START_STATE ((void *)0) +#define RUNNING_STATE ((void *)1) +#define DONE_STATE ((void *)2) +#define ERROR_STATE ((void *)-1) + +#define QUEUE_RUNNING 0 +#define QUEUE_STOPPED 1 + +#define MRST_SPI_DEASSERT 0 +#define MRST_SPI_ASSERT 1 + +/* Slave spi_dev related */ +struct chip_data { + u16 cr0; + u8 cs; /* chip select pin */ + u8 n_bytes; /* current is a 1/2/4 byte op */ + u8 tmode; /* TR/TO/RO/EEPROM */ + u8 type; /* SPI/SSP/MicroWire */ + + u8 poll_mode; /* 1 means use poll mode */ + + u32 dma_width; + u32 rx_threshold; + u32 tx_threshold; + u8 enable_dma; + u8 bits_per_word; + u16 clk_div; /* baud rate divider */ + u32 speed_hz; /* baud rate */ + int (*write)(struct dw_spi *dws); + int (*read)(struct dw_spi *dws); + void (*cs_control)(u32 command); +}; + +#ifdef CONFIG_DEBUG_FS +static int spi_show_regs_open(struct inode *inode, struct file *file) +{ + file->private_data = inode->i_private; + return 0; +} + +#define SPI_REGS_BUFSIZE 1024 +static ssize_t spi_show_regs(struct file *file, char __user *user_buf, + size_t count, loff_t *ppos) +{ + struct dw_spi *dws; + char *buf; + u32 len = 0; + ssize_t ret; + + dws = file->private_data; + + buf = kzalloc(SPI_REGS_BUFSIZE, GFP_KERNEL); + if (!buf) + return 0; + + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "MRST SPI0 registers:\n"); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "=================================\n"); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "CTRL0: \t\t0x%08x\n", dw_readl(dws, ctrl0)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "CTRL1: \t\t0x%08x\n", dw_readl(dws, ctrl1)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "SSIENR: \t0x%08x\n", dw_readl(dws, ssienr)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "SER: \t\t0x%08x\n", dw_readl(dws, ser)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "BAUDR: \t\t0x%08x\n", dw_readl(dws, baudr)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "TXFTLR: \t0x%08x\n", dw_readl(dws, txfltr)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "RXFTLR: \t0x%08x\n", dw_readl(dws, rxfltr)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "TXFLR: \t\t0x%08x\n", dw_readl(dws, txflr)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "RXFLR: \t\t0x%08x\n", dw_readl(dws, rxflr)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "SR: \t\t0x%08x\n", dw_readl(dws, sr)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "IMR: \t\t0x%08x\n", dw_readl(dws, imr)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "ISR: \t\t0x%08x\n", dw_readl(dws, isr)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "DMACR: \t\t0x%08x\n", dw_readl(dws, dmacr)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "DMATDLR: \t0x%08x\n", dw_readl(dws, dmatdlr)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "DMARDLR: \t0x%08x\n", dw_readl(dws, dmardlr)); + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, + "=================================\n"); + + ret = simple_read_from_buffer(user_buf, count, ppos, buf, len); + kfree(buf); + return ret; +} + +static const struct file_operations mrst_spi_regs_ops = { + .owner = THIS_MODULE, + .open = spi_show_regs_open, + .read = spi_show_regs, +}; + +static int mrst_spi_debugfs_init(struct dw_spi *dws) +{ + dws->debugfs = debugfs_create_dir("mrst_spi", NULL); + if (!dws->debugfs) + return -ENOMEM; + + debugfs_create_file("registers", S_IFREG | S_IRUGO, + dws->debugfs, (void *)dws, &mrst_spi_regs_ops); + return 0; +} + +static void mrst_spi_debugfs_remove(struct dw_spi *dws) +{ + if (dws->debugfs) + debugfs_remove_recursive(dws->debugfs); +} + +#else +static inline int mrst_spi_debugfs_init(struct dw_spi *dws) +{ +} + +static inline void mrst_spi_debugfs_remove(struct dw_spi *dws) +{ +} +#endif /* CONFIG_DEBUG_FS */ + +static void wait_till_not_busy(struct dw_spi *dws) +{ + unsigned long end = jiffies + usecs_to_jiffies(1000); + + while (time_before(jiffies, end)) { + if (!(dw_readw(dws, sr) & SR_BUSY)) + return; + } + dev_err(&dws->master->dev, + "DW SPI: Stutus keeps busy for 1000us after a read/write!\n"); +} + +static void flush(struct dw_spi *dws) +{ + while (dw_readw(dws, sr) & SR_RF_NOT_EMPT) + dw_readw(dws, dr); + + wait_till_not_busy(dws); +} + +static void null_cs_control(u32 command) +{ +} + +static int null_writer(struct dw_spi *dws) +{ + u8 n_bytes = dws->n_bytes; + + if (!(dw_readw(dws, sr) & SR_TF_NOT_FULL) + || (dws->tx == dws->tx_end)) + return 0; + dw_writew(dws, dr, 0); + dws->tx += n_bytes; + + wait_till_not_busy(dws); + return 1; +} + +static int null_reader(struct dw_spi *dws) +{ + u8 n_bytes = dws->n_bytes; + + while ((dw_readw(dws, sr) & SR_RF_NOT_EMPT) + && (dws->rx < dws->rx_end)) { + dw_readw(dws, dr); + dws->rx += n_bytes; + } + wait_till_not_busy(dws); + return dws->rx == dws->rx_end; +} + +static int u8_writer(struct dw_spi *dws) +{ + if (!(dw_readw(dws, sr) & SR_TF_NOT_FULL) + || (dws->tx == dws->tx_end)) + return 0; + + dw_writew(dws, dr, *(u8 *)(dws->tx)); + ++dws->tx; + + wait_till_not_busy(dws); + return 1; +} + +static int u8_reader(struct dw_spi *dws) +{ + while ((dw_readw(dws, sr) & SR_RF_NOT_EMPT) + && (dws->rx < dws->rx_end)) { + *(u8 *)(dws->rx) = dw_readw(dws, dr); + ++dws->rx; + } + + wait_till_not_busy(dws); + return dws->rx == dws->rx_end; +} + +static int u16_writer(struct dw_spi *dws) +{ + if (!(dw_readw(dws, sr) & SR_TF_NOT_FULL) + || (dws->tx == dws->tx_end)) + return 0; + + dw_writew(dws, dr, *(u16 *)(dws->tx)); + dws->tx += 2; + + wait_till_not_busy(dws); + return 1; +} + +static int u16_reader(struct dw_spi *dws) +{ + u16 temp; + + while ((dw_readw(dws, sr) & SR_RF_NOT_EMPT) + && (dws->rx < dws->rx_end)) { + temp = dw_readw(dws, dr); + *(u16 *)(dws->rx) = temp; + dws->rx += 2; + } + + wait_till_not_busy(dws); + return dws->rx == dws->rx_end; +} + +static void *next_transfer(struct dw_spi *dws) +{ + struct spi_message *msg = dws->cur_msg; + struct spi_transfer *trans = dws->cur_transfer; + + /* Move to next transfer */ + if (trans->transfer_list.next != &msg->transfers) { + dws->cur_transfer = + list_entry(trans->transfer_list.next, + struct spi_transfer, + transfer_list); + return RUNNING_STATE; + } else + return DONE_STATE; +} + +/* + * Note: first step is the protocol driver prepares + * a dma-capable memory, and this func just need translate + * the virt addr to physical + */ +static int map_dma_buffers(struct dw_spi *dws) +{ + if (!dws->cur_msg->is_dma_mapped || !dws->dma_inited + || !dws->cur_chip->enable_dma) + return 0; + + if (dws->cur_transfer->tx_dma) + dws->tx_dma = dws->cur_transfer->tx_dma; + + if (dws->cur_transfer->rx_dma) + dws->rx_dma = dws->cur_transfer->rx_dma; + + return 1; +} + +/* Caller already set message->status; dma and pio irqs are blocked */ +static void giveback(struct dw_spi *dws) +{ + struct spi_transfer *last_transfer; + unsigned long flags; + struct spi_message *msg; + + spin_lock_irqsave(&dws->lock, flags); + msg = dws->cur_msg; + dws->cur_msg = NULL; + dws->cur_transfer = NULL; + dws->prev_chip = dws->cur_chip; + dws->cur_chip = NULL; + dws->dma_mapped = 0; + queue_work(dws->workqueue, &dws->pump_messages); + spin_unlock_irqrestore(&dws->lock, flags); + + last_transfer = list_entry(msg->transfers.prev, + struct spi_transfer, + transfer_list); + + if (!last_transfer->cs_change) + dws->cs_control(MRST_SPI_DEASSERT); + + msg->state = NULL; + if (msg->complete) + msg->complete(msg->context); +} + +static void int_error_stop(struct dw_spi *dws, const char *msg) +{ + /* Stop and reset hw */ + flush(dws); + spi_enable_chip(dws, 0); + + dev_err(&dws->master->dev, "%s\n", msg); + dws->cur_msg->state = ERROR_STATE; + tasklet_schedule(&dws->pump_transfers); +} + +static void transfer_complete(struct dw_spi *dws) +{ + /* Update total byte transfered return count actual bytes read */ + dws->cur_msg->actual_length += dws->len; + + /* Move to next transfer */ + dws->cur_msg->state = next_transfer(dws); + + /* Handle end of message */ + if (dws->cur_msg->state == DONE_STATE) { + dws->cur_msg->status = 0; + giveback(dws); + } else + tasklet_schedule(&dws->pump_transfers); +} + +static irqreturn_t interrupt_transfer(struct dw_spi *dws) +{ + u16 irq_status, irq_mask = 0x3f; + + irq_status = dw_readw(dws, isr) & irq_mask; + /* Error handling */ + if (irq_status & (SPI_INT_TXOI | SPI_INT_RXOI | SPI_INT_RXUI)) { + dw_readw(dws, txoicr); + dw_readw(dws, rxoicr); + dw_readw(dws, rxuicr); + int_error_stop(dws, "interrupt_transfer: fifo overrun"); + return IRQ_HANDLED; + } + + /* INT comes from tx */ + if (dws->tx && (irq_status & SPI_INT_TXEI)) { + while (dws->tx < dws->tx_end) + dws->write(dws); + + if (dws->tx == dws->tx_end) { + spi_mask_intr(dws, SPI_INT_TXEI); + transfer_complete(dws); + } + } + + /* INT comes from rx */ + if (dws->rx && (irq_status & SPI_INT_RXFI)) { + if (dws->read(dws)) + transfer_complete(dws); + } + return IRQ_HANDLED; +} + +static irqreturn_t dw_spi_irq(int irq, void *dev_id) +{ + struct dw_spi *dws = dev_id; + + if (!dws->cur_msg) { + spi_mask_intr(dws, SPI_INT_TXEI); + /* Never fail */ + return IRQ_HANDLED; + } + + return dws->transfer_handler(dws); +} + +/* Must be called inside pump_transfers() */ +static void poll_transfer(struct dw_spi *dws) +{ + if (dws->tx) { + while (dws->write(dws)) + dws->read(dws); + } + + dws->read(dws); + transfer_complete(dws); +} + +static void dma_transfer(struct dw_spi *dws, int cs_change) +{ +} + +static void pump_transfers(unsigned long data) +{ + struct dw_spi *dws = (struct dw_spi *)data; + struct spi_message *message = NULL; + struct spi_transfer *transfer = NULL; + struct spi_transfer *previous = NULL; + struct spi_device *spi = NULL; + struct chip_data *chip = NULL; + u8 bits = 0; + u8 imask = 0; + u8 cs_change = 0; + u16 clk_div = 0; + u32 speed = 0; + u32 cr0 = 0; + + /* Get current state information */ + message = dws->cur_msg; + transfer = dws->cur_transfer; + chip = dws->cur_chip; + spi = message->spi; + + if (message->state == ERROR_STATE) { + message->status = -EIO; + goto early_exit; + } + + /* Handle end of message */ + if (message->state == DONE_STATE) { + message->status = 0; + goto early_exit; + } + + /* Delay if requested at end of transfer*/ + if (message->state == RUNNING_STATE) { + previous = list_entry(transfer->transfer_list.prev, + struct spi_transfer, + transfer_list); + if (previous->delay_usecs) + udelay(previous->delay_usecs); + } + + dws->n_bytes = chip->n_bytes; + dws->dma_width = chip->dma_width; + dws->cs_control = chip->cs_control; + + dws->rx_dma = transfer->rx_dma; + dws->tx_dma = transfer->tx_dma; + dws->tx = (void *)transfer->tx_buf; + dws->tx_end = dws->tx + transfer->len; + dws->rx = transfer->rx_buf; + dws->rx_end = dws->rx + transfer->len; + dws->write = dws->tx ? chip->write : null_writer; + dws->read = dws->rx ? chip->read : null_reader; + dws->cs_change = transfer->cs_change; + dws->len = dws->cur_transfer->len; + if (chip != dws->prev_chip) + cs_change = 1; + + cr0 = chip->cr0; + + /* Handle per transfer options for bpw and speed */ + if (transfer->speed_hz) { + speed = chip->speed_hz; + + if (transfer->speed_hz != speed) { + speed = transfer->speed_hz; + if (speed > dws->max_freq) { + printk(KERN_ERR "MRST SPI0: unsupported" + "freq: %dHz\n", speed); + message->status = -EIO; + goto early_exit; + } + + /* clk_div doesn't support odd number */ + clk_div = dws->max_freq / speed; + clk_div = (clk_div >> 1) << 1; + + chip->speed_hz = speed; + chip->clk_div = clk_div; + } + } + if (transfer->bits_per_word) { + bits = transfer->bits_per_word; + + switch (bits) { + case 8: + dws->n_bytes = 1; + dws->dma_width = 1; + dws->read = (dws->read != null_reader) ? + u8_reader : null_reader; + dws->write = (dws->write != null_writer) ? + u8_writer : null_writer; + break; + case 16: + dws->n_bytes = 2; + dws->dma_width = 2; + dws->read = (dws->read != null_reader) ? + u16_reader : null_reader; + dws->write = (dws->write != null_writer) ? + u16_writer : null_writer; + break; + default: + printk(KERN_ERR "MRST SPI0: unsupported bits:" + "%db\n", bits); + message->status = -EIO; + goto early_exit; + } + + cr0 = (bits - 1) + | (chip->type << SPI_FRF_OFFSET) + | (spi->mode << SPI_MODE_OFFSET) + | (chip->tmode << SPI_TMOD_OFFSET); + } + message->state = RUNNING_STATE; + + /* Check if current transfer is a DMA transaction */ + dws->dma_mapped = map_dma_buffers(dws); + + if (!dws->dma_mapped && !chip->poll_mode) { + if (dws->rx) + imask |= SPI_INT_RXFI; + if (dws->tx) + imask |= SPI_INT_TXEI; + dws->transfer_handler = interrupt_transfer; + } + + /* + * Reprogram registers only if + * 1. chip select changes + * 2. clk_div is changed + * 3. control value changes + */ + if (dw_readw(dws, ctrl0) != cr0 || cs_change || clk_div) { + spi_enable_chip(dws, 0); + + if (dw_readw(dws, ctrl0) != cr0) + dw_writew(dws, ctrl0, cr0); + + /* Set the interrupt mask, for poll mode just diable all int */ + spi_mask_intr(dws, 0xff); + if (!chip->poll_mode) + spi_umask_intr(dws, imask); + + spi_set_clk(dws, clk_div ? clk_div : chip->clk_div); + spi_chip_sel(dws, spi->chip_select); + spi_enable_chip(dws, 1); + + if (cs_change) + dws->prev_chip = chip; + } + + if (dws->dma_mapped) + dma_transfer(dws, cs_change); + + if (chip->poll_mode) + poll_transfer(dws); + + return; + +early_exit: + giveback(dws); + return; +} + +static void pump_messages(struct work_struct *work) +{ + struct dw_spi *dws = + container_of(work, struct dw_spi, pump_messages); + unsigned long flags; + + /* Lock queue and check for queue work */ + spin_lock_irqsave(&dws->lock, flags); + if (list_empty(&dws->queue) || dws->run == QUEUE_STOPPED) { + dws->busy = 0; + spin_unlock_irqrestore(&dws->lock, flags); + return; + } + + /* Make sure we are not already running a message */ + if (dws->cur_msg) { + spin_unlock_irqrestore(&dws->lock, flags); + return; + } + + /* Extract head of queue */ + dws->cur_msg = list_entry(dws->queue.next, struct spi_message, queue); + list_del_init(&dws->cur_msg->queue); + + /* Initial message state*/ + dws->cur_msg->state = START_STATE; + dws->cur_transfer = list_entry(dws->cur_msg->transfers.next, + struct spi_transfer, + transfer_list); + dws->cur_chip = spi_get_ctldata(dws->cur_msg->spi); + + /* Mark as busy and launch transfers */ + tasklet_schedule(&dws->pump_transfers); + + dws->busy = 1; + spin_unlock_irqrestore(&dws->lock, flags); +} + +/* spi_device use this to queue in their spi_msg */ +static int dw_spi_transfer(struct spi_device *spi, struct spi_message *msg) +{ + struct dw_spi *dws = spi_master_get_devdata(spi->master); + unsigned long flags; + + spin_lock_irqsave(&dws->lock, flags); + + if (dws->run == QUEUE_STOPPED) { + spin_unlock_irqrestore(&dws->lock, flags); + return -ESHUTDOWN; + } + + msg->actual_length = 0; + msg->status = -EINPROGRESS; + msg->state = START_STATE; + + list_add_tail(&msg->queue, &dws->queue); + + if (dws->run == QUEUE_RUNNING && !dws->busy) { + + if (dws->cur_transfer || dws->cur_msg) + queue_work(dws->workqueue, + &dws->pump_messages); + else { + /* If no other data transaction in air, just go */ + spin_unlock_irqrestore(&dws->lock, flags); + pump_messages(&dws->pump_messages); + return 0; + } + } + + spin_unlock_irqrestore(&dws->lock, flags); + return 0; +} + +/* This may be called twice for each spi dev */ +static int dw_spi_setup(struct spi_device *spi) +{ + struct dw_spi_chip *chip_info = NULL; + struct chip_data *chip; + + if (spi->bits_per_word != 8 && spi->bits_per_word != 16) + return -EINVAL; + + /* Only alloc on first setup */ + chip = spi_get_ctldata(spi); + if (!chip) { + chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL); + if (!chip) + return -ENOMEM; + + chip->cs_control = null_cs_control; + chip->enable_dma = 0; + } + + /* + * Protocol drivers may change the chip settings, so... + * if chip_info exists, use it + */ + chip_info = spi->controller_data; + + /* chip_info doesn't always exist */ + if (chip_info) { + if (chip_info->cs_control) + chip->cs_control = chip_info->cs_control; + + chip->poll_mode = chip_info->poll_mode; + chip->type = chip_info->type; + + chip->rx_threshold = 0; + chip->tx_threshold = 0; + + chip->enable_dma = chip_info->enable_dma; + } + + if (spi->bits_per_word <= 8) { + chip->n_bytes = 1; + chip->dma_width = 1; + chip->read = u8_reader; + chip->write = u8_writer; + } else if (spi->bits_per_word <= 16) { + chip->n_bytes = 2; + chip->dma_width = 2; + chip->read = u16_reader; + chip->write = u16_writer; + } else { + /* Never take >16b case for MRST SPIC */ + dev_err(&spi->dev, "invalid wordsize\n"); + return -EINVAL; + } + chip->bits_per_word = spi->bits_per_word; + + chip->speed_hz = spi->max_speed_hz; + if (chip->speed_hz) + chip->clk_div = 25000000 / chip->speed_hz; + else + chip->clk_div = 8; /* default value */ + + chip->tmode = 0; /* Tx & Rx */ + /* Default SPI mode is SCPOL = 0, SCPH = 0 */ + chip->cr0 = (chip->bits_per_word - 1) + | (chip->type << SPI_FRF_OFFSET) + | (spi->mode << SPI_MODE_OFFSET) + | (chip->tmode << SPI_TMOD_OFFSET); + + spi_set_ctldata(spi, chip); + return 0; +} + +static void dw_spi_cleanup(struct spi_device *spi) +{ + struct chip_data *chip = spi_get_ctldata(spi); + kfree(chip); +} + +static int __init init_queue(struct dw_spi *dws) +{ + INIT_LIST_HEAD(&dws->queue); + spin_lock_init(&dws->lock); + + dws->run = QUEUE_STOPPED; + dws->busy = 0; + + tasklet_init(&dws->pump_transfers, + pump_transfers, (unsigned long)dws); + + INIT_WORK(&dws->pump_messages, pump_messages); + dws->workqueue = create_singlethread_workqueue( + dev_name(dws->master->dev.parent)); + if (dws->workqueue == NULL) + return -EBUSY; + + return 0; +} + +static int start_queue(struct dw_spi *dws) +{ + unsigned long flags; + + spin_lock_irqsave(&dws->lock, flags); + + if (dws->run == QUEUE_RUNNING || dws->busy) { + spin_unlock_irqrestore(&dws->lock, flags); + return -EBUSY; + } + + dws->run = QUEUE_RUNNING; + dws->cur_msg = NULL; + dws->cur_transfer = NULL; + dws->cur_chip = NULL; + dws->prev_chip = NULL; + spin_unlock_irqrestore(&dws->lock, flags); + + queue_work(dws->workqueue, &dws->pump_messages); + + return 0; +} + +static int stop_queue(struct dw_spi *dws) +{ + unsigned long flags; + unsigned limit = 50; + int status = 0; + + spin_lock_irqsave(&dws->lock, flags); + dws->run = QUEUE_STOPPED; + while (!list_empty(&dws->queue) && dws->busy && limit--) { + spin_unlock_irqrestore(&dws->lock, flags); + msleep(10); + spin_lock_irqsave(&dws->lock, flags); + } + + if (!list_empty(&dws->queue) || dws->busy) + status = -EBUSY; + spin_unlock_irqrestore(&dws->lock, flags); + + return status; +} + +static int destroy_queue(struct dw_spi *dws) +{ + int status; + + status = stop_queue(dws); + if (status != 0) + return status; + destroy_workqueue(dws->workqueue); + return 0; +} + +/* Restart the controller, disable all interrupts, clean rx fifo */ +static void spi_hw_init(struct dw_spi *dws) +{ + spi_enable_chip(dws, 0); + spi_mask_intr(dws, 0xff); + spi_enable_chip(dws, 1); + flush(dws); +} + +int __devinit dw_spi_add_host(struct dw_spi *dws) +{ + struct spi_master *master; + int ret; + + BUG_ON(dws == NULL); + + master = spi_alloc_master(dws->parent_dev, 0); + if (!master) { + ret = -ENOMEM; + goto exit; + } + + dws->master = master; + dws->type = SSI_MOTO_SPI; + dws->prev_chip = NULL; + dws->dma_inited = 0; + dws->dma_addr = (dma_addr_t)(dws->paddr + 0x60); + + ret = request_irq(dws->irq, dw_spi_irq, 0, + "dw_spi", dws); + if (ret < 0) { + dev_err(&master->dev, "can not get IRQ\n"); + goto err_free_master; + } + + master->mode_bits = SPI_CPOL | SPI_CPHA; + master->bus_num = dws->bus_num; + master->num_chipselect = dws->num_cs; + master->cleanup = dw_spi_cleanup; + master->setup = dw_spi_setup; + master->transfer = dw_spi_transfer; + + dws->dma_inited = 0; + + /* Basic HW init */ + spi_hw_init(dws); + + /* Initial and start queue */ + ret = init_queue(dws); + if (ret) { + dev_err(&master->dev, "problem initializing queue\n"); + goto err_diable_hw; + } + ret = start_queue(dws); + if (ret) { + dev_err(&master->dev, "problem starting queue\n"); + goto err_diable_hw; + } + + spi_master_set_devdata(master, dws); + ret = spi_register_master(master); + if (ret) { + dev_err(&master->dev, "problem registering spi master\n"); + goto err_queue_alloc; + } + + mrst_spi_debugfs_init(dws); + return 0; + +err_queue_alloc: + destroy_queue(dws); +err_diable_hw: + spi_enable_chip(dws, 0); + free_irq(dws->irq, dws); +err_free_master: + spi_master_put(master); +exit: + return ret; +} +EXPORT_SYMBOL(dw_spi_add_host); + +void __devexit dw_spi_remove_host(struct dw_spi *dws) +{ + int status = 0; + + if (!dws) + return; + mrst_spi_debugfs_remove(dws); + + /* Remove the queue */ + status = destroy_queue(dws); + if (status != 0) + dev_err(&dws->master->dev, "dw_spi_remove: workqueue will not " + "complete, message memory not freed\n"); + + spi_enable_chip(dws, 0); + /* Disable clk */ + spi_set_clk(dws, 0); + free_irq(dws->irq, dws); + + /* Disconnect from the SPI framework */ + spi_unregister_master(dws->master); +} + +int dw_spi_suspend_host(struct dw_spi *dws) +{ + int ret = 0; + + ret = stop_queue(dws); + if (ret) + return ret; + spi_enable_chip(dws, 0); + spi_set_clk(dws, 0); + return ret; +} +EXPORT_SYMBOL(dw_spi_suspend_host); + +int dw_spi_resume_host(struct dw_spi *dws) +{ + int ret; + + spi_hw_init(dws); + ret = start_queue(dws); + if (ret) + dev_err(&dws->master->dev, "fail to start queue (%d)\n", ret); + return ret; +} +EXPORT_SYMBOL(dw_spi_resume_host); + +MODULE_AUTHOR("Feng Tang "); +MODULE_DESCRIPTION("Driver for DesignWare SPI controller core"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/spi/dw_spi_pci.c b/drivers/spi/dw_spi_pci.c new file mode 100644 index 000000000000..34ba69161734 --- /dev/null +++ b/drivers/spi/dw_spi_pci.c @@ -0,0 +1,169 @@ +/* + * mrst_spi_pci.c - PCI interface driver for DW SPI Core + * + * Copyright (c) 2009, Intel Corporation. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, + * Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + */ + +#include +#include +#include +#include + +#define DRIVER_NAME "dw_spi_pci" + +struct dw_spi_pci { + struct pci_dev *pdev; + struct dw_spi dws; +}; + +static int __devinit spi_pci_probe(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + struct dw_spi_pci *dwpci; + struct dw_spi *dws; + int pci_bar = 0; + int ret; + + printk(KERN_INFO "DW: found PCI SPI controller(ID: %04x:%04x)\n", + pdev->vendor, pdev->device); + + ret = pci_enable_device(pdev); + if (ret) + return ret; + + dwpci = kzalloc(sizeof(struct dw_spi_pci), GFP_KERNEL); + if (!dwpci) { + ret = -ENOMEM; + goto err_disable; + } + + dwpci->pdev = pdev; + dws = &dwpci->dws; + + /* Get basic io resource and map it */ + dws->paddr = pci_resource_start(pdev, pci_bar); + dws->iolen = pci_resource_len(pdev, pci_bar); + + ret = pci_request_region(pdev, pci_bar, dev_name(&pdev->dev)); + if (ret) + goto err_kfree; + + dws->regs = ioremap_nocache((unsigned long)dws->paddr, + pci_resource_len(pdev, pci_bar)); + if (!dws->regs) { + ret = -ENOMEM; + goto err_release_reg; + } + + dws->parent_dev = &pdev->dev; + dws->bus_num = 0; + dws->num_cs = 4; + dws->max_freq = 25000000; /* for Moorestwon */ + dws->irq = pdev->irq; + + ret = dw_spi_add_host(dws); + if (ret) + goto err_unmap; + + /* PCI hook and SPI hook use the same drv data */ + pci_set_drvdata(pdev, dwpci); + return 0; + +err_unmap: + iounmap(dws->regs); +err_release_reg: + pci_release_region(pdev, pci_bar); +err_kfree: + kfree(dwpci); +err_disable: + pci_disable_device(pdev); + return ret; +} + +static void __devexit spi_pci_remove(struct pci_dev *pdev) +{ + struct dw_spi_pci *dwpci = pci_get_drvdata(pdev); + + pci_set_drvdata(pdev, NULL); + iounmap(dwpci->dws.regs); + pci_release_region(pdev, 0); + kfree(dwpci); + pci_disable_device(pdev); +} + +#ifdef CONFIG_PM +static int spi_suspend(struct pci_dev *pdev, pm_message_t state) +{ + struct dw_spi_pci *dwpci = pci_get_drvdata(pdev); + int ret; + + ret = dw_spi_suspend_host(&dwpci->dws); + if (ret) + return ret; + pci_save_state(pdev); + pci_disable_device(pdev); + pci_set_power_state(pdev, pci_choose_state(pdev, state)); + return ret; +} + +static int spi_resume(struct pci_dev *pdev) +{ + struct dw_spi_pci *dwpci = pci_get_drvdata(pdev); + int ret; + + pci_set_power_state(pdev, PCI_D0); + pci_restore_state(pdev); + ret = pci_enable_device(pdev); + if (ret) + return ret; + return dw_spi_resume_host(&dwpci->dws); +} +#else +#define spi_suspend NULL +#define spi_resume NULL +#endif + +static const struct pci_device_id pci_ids[] __devinitdata = { + /* Intel Moorestown platform SPI controller 0 */ + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x0800) }, + {}, +}; + +static struct pci_driver dw_spi_driver = { + .name = DRIVER_NAME, + .id_table = pci_ids, + .probe = spi_pci_probe, + .remove = __devexit_p(spi_pci_remove), + .suspend = spi_suspend, + .resume = spi_resume, +}; + +static int __init mrst_spi_init(void) +{ + return pci_register_driver(&dw_spi_driver); +} + +static void __exit mrst_spi_exit(void) +{ + pci_unregister_driver(&dw_spi_driver); +} + +module_init(mrst_spi_init); +module_exit(mrst_spi_exit); + +MODULE_AUTHOR("Feng Tang "); +MODULE_DESCRIPTION("PCI interface driver for DW SPI Core"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c index 73e24ef5a2f9..1d41058bbab2 100644 --- a/drivers/spi/spi_bfin5xx.c +++ b/drivers/spi/spi_bfin5xx.c @@ -1294,7 +1294,7 @@ static int __init bfin_spi_probe(struct platform_device *pdev) goto out_error_get_res; } - drv_data->regs_base = ioremap(res->start, (res->end - res->start + 1)); + drv_data->regs_base = ioremap(res->start, resource_size(res)); if (drv_data->regs_base == NULL) { dev_err(dev, "Cannot map IO\n"); status = -ENXIO; diff --git a/drivers/spi/spi_mpc8xxx.c b/drivers/spi/spi_mpc8xxx.c index e9390d747bfc..1fb2a6ea328c 100644 --- a/drivers/spi/spi_mpc8xxx.c +++ b/drivers/spi/spi_mpc8xxx.c @@ -1013,7 +1013,7 @@ mpc8xxx_spi_probe(struct device *dev, struct resource *mem, unsigned int irq) init_completion(&mpc8xxx_spi->done); - mpc8xxx_spi->base = ioremap(mem->start, mem->end - mem->start + 1); + mpc8xxx_spi->base = ioremap(mem->start, resource_size(mem)); if (mpc8xxx_spi->base == NULL) { ret = -ENOMEM; goto err_ioremap; diff --git a/drivers/spi/spi_s3c24xx.c b/drivers/spi/spi_s3c24xx.c index 276591569c8b..c010733877ae 100644 --- a/drivers/spi/spi_s3c24xx.c +++ b/drivers/spi/spi_s3c24xx.c @@ -1,7 +1,7 @@ /* linux/drivers/spi/spi_s3c24xx.c * * Copyright (c) 2006 Ben Dooks - * Copyright (c) 2006 Simtec Electronics + * Copyright 2006-2009 Simtec Electronics * Ben Dooks * * This program is free software; you can redistribute it and/or modify @@ -28,6 +28,11 @@ #include #include +#include +#include + +#include "spi_s3c24xx_fiq.h" + /** * s3c24xx_spi_devstate - per device data * @hz: Last frequency calculated for @sppre field. @@ -42,6 +47,13 @@ struct s3c24xx_spi_devstate { u8 sppre; }; +enum spi_fiq_mode { + FIQ_MODE_NONE = 0, + FIQ_MODE_TX = 1, + FIQ_MODE_RX = 2, + FIQ_MODE_TXRX = 3, +}; + struct s3c24xx_spi { /* bitbang has to be first */ struct spi_bitbang bitbang; @@ -52,6 +64,11 @@ struct s3c24xx_spi { int len; int count; + struct fiq_handler fiq_handler; + enum spi_fiq_mode fiq_mode; + unsigned char fiq_inuse; + unsigned char fiq_claimed; + void (*set_cs)(struct s3c2410_spi_info *spi, int cs, int pol); @@ -67,6 +84,7 @@ struct s3c24xx_spi { struct s3c2410_spi_info *pdata; }; + #define SPCON_DEFAULT (S3C2410_SPCON_MSTR | S3C2410_SPCON_SMOD_INT) #define SPPIN_DEFAULT (S3C2410_SPPIN_KEEP) @@ -127,7 +145,7 @@ static int s3c24xx_spi_update_state(struct spi_device *spi, } if (spi->mode != cs->mode) { - u8 spcon = SPCON_DEFAULT; + u8 spcon = SPCON_DEFAULT | S3C2410_SPCON_ENSCK; if (spi->mode & SPI_CPHA) spcon |= S3C2410_SPCON_CPHA_FMTB; @@ -214,13 +232,196 @@ static inline unsigned int hw_txbyte(struct s3c24xx_spi *hw, int count) return hw->tx ? hw->tx[count] : 0; } +#ifdef CONFIG_SPI_S3C24XX_FIQ +/* Support for FIQ based pseudo-DMA to improve the transfer speed. + * + * This code uses the assembly helper in spi_s3c24xx_spi.S which is + * used by the FIQ core to move data between main memory and the peripheral + * block. Since this is code running on the processor, there is no problem + * with cache coherency of the buffers, so we can use any buffer we like. + */ + +/** + * struct spi_fiq_code - FIQ code and header + * @length: The length of the code fragment, excluding this header. + * @ack_offset: The offset from @data to the word to place the IRQ ACK bit at. + * @data: The code itself to install as a FIQ handler. + */ +struct spi_fiq_code { + u32 length; + u32 ack_offset; + u8 data[0]; +}; + +extern struct spi_fiq_code s3c24xx_spi_fiq_txrx; +extern struct spi_fiq_code s3c24xx_spi_fiq_tx; +extern struct spi_fiq_code s3c24xx_spi_fiq_rx; + +/** + * ack_bit - turn IRQ into IRQ acknowledgement bit + * @irq: The interrupt number + * + * Returns the bit to write to the interrupt acknowledge register. + */ +static inline u32 ack_bit(unsigned int irq) +{ + return 1 << (irq - IRQ_EINT0); +} + +/** + * s3c24xx_spi_tryfiq - attempt to claim and setup FIQ for transfer + * @hw: The hardware state. + * + * Claim the FIQ handler (only one can be active at any one time) and + * then setup the correct transfer code for this transfer. + * + * This call updates all the necessary state information if sucessful, + * so the caller does not need to do anything more than start the transfer + * as normal, since the IRQ will have been re-routed to the FIQ handler. +*/ +void s3c24xx_spi_tryfiq(struct s3c24xx_spi *hw) +{ + struct pt_regs regs; + enum spi_fiq_mode mode; + struct spi_fiq_code *code; + int ret; + + if (!hw->fiq_claimed) { + /* try and claim fiq if we haven't got it, and if not + * then return and simply use another transfer method */ + + ret = claim_fiq(&hw->fiq_handler); + if (ret) + return; + } + + if (hw->tx && !hw->rx) + mode = FIQ_MODE_TX; + else if (hw->rx && !hw->tx) + mode = FIQ_MODE_RX; + else + mode = FIQ_MODE_TXRX; + + regs.uregs[fiq_rspi] = (long)hw->regs; + regs.uregs[fiq_rrx] = (long)hw->rx; + regs.uregs[fiq_rtx] = (long)hw->tx + 1; + regs.uregs[fiq_rcount] = hw->len - 1; + regs.uregs[fiq_rirq] = (long)S3C24XX_VA_IRQ; + + set_fiq_regs(®s); + + if (hw->fiq_mode != mode) { + u32 *ack_ptr; + + hw->fiq_mode = mode; + + switch (mode) { + case FIQ_MODE_TX: + code = &s3c24xx_spi_fiq_tx; + break; + case FIQ_MODE_RX: + code = &s3c24xx_spi_fiq_rx; + break; + case FIQ_MODE_TXRX: + code = &s3c24xx_spi_fiq_txrx; + break; + default: + code = NULL; + } + + BUG_ON(!code); + + ack_ptr = (u32 *)&code->data[code->ack_offset]; + *ack_ptr = ack_bit(hw->irq); + + set_fiq_handler(&code->data, code->length); + } + + s3c24xx_set_fiq(hw->irq, true); + + hw->fiq_mode = mode; + hw->fiq_inuse = 1; +} + +/** + * s3c24xx_spi_fiqop - FIQ core code callback + * @pw: Data registered with the handler + * @release: Whether this is a release or a return. + * + * Called by the FIQ code when another module wants to use the FIQ, so + * return whether we are currently using this or not and then update our + * internal state. + */ +static int s3c24xx_spi_fiqop(void *pw, int release) +{ + struct s3c24xx_spi *hw = pw; + int ret = 0; + + if (release) { + if (hw->fiq_inuse) + ret = -EBUSY; + + /* note, we do not need to unroute the FIQ, as the FIQ + * vector code de-routes it to signal the end of transfer */ + + hw->fiq_mode = FIQ_MODE_NONE; + hw->fiq_claimed = 0; + } else { + hw->fiq_claimed = 1; + } + + return ret; +} + +/** + * s3c24xx_spi_initfiq - setup the information for the FIQ core + * @hw: The hardware state. + * + * Setup the fiq_handler block to pass to the FIQ core. + */ +static inline void s3c24xx_spi_initfiq(struct s3c24xx_spi *hw) +{ + hw->fiq_handler.dev_id = hw; + hw->fiq_handler.name = dev_name(hw->dev); + hw->fiq_handler.fiq_op = s3c24xx_spi_fiqop; +} + +/** + * s3c24xx_spi_usefiq - return if we should be using FIQ. + * @hw: The hardware state. + * + * Return true if the platform data specifies whether this channel is + * allowed to use the FIQ. + */ +static inline bool s3c24xx_spi_usefiq(struct s3c24xx_spi *hw) +{ + return hw->pdata->use_fiq; +} + +/** + * s3c24xx_spi_usingfiq - return if channel is using FIQ + * @spi: The hardware state. + * + * Return whether the channel is currently using the FIQ (separate from + * whether the FIQ is claimed). + */ +static inline bool s3c24xx_spi_usingfiq(struct s3c24xx_spi *spi) +{ + return spi->fiq_inuse; +} +#else + +static inline void s3c24xx_spi_initfiq(struct s3c24xx_spi *s) { } +static inline void s3c24xx_spi_tryfiq(struct s3c24xx_spi *s) { } +static inline bool s3c24xx_spi_usefiq(struct s3c24xx_spi *s) { return false; } +static inline bool s3c24xx_spi_usingfiq(struct s3c24xx_spi *s) { return false; } + +#endif /* CONFIG_SPI_S3C24XX_FIQ */ + static int s3c24xx_spi_txrx(struct spi_device *spi, struct spi_transfer *t) { struct s3c24xx_spi *hw = to_hw(spi); - dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n", - t->tx_buf, t->rx_buf, t->len); - hw->tx = t->tx_buf; hw->rx = t->rx_buf; hw->len = t->len; @@ -228,11 +429,14 @@ static int s3c24xx_spi_txrx(struct spi_device *spi, struct spi_transfer *t) init_completion(&hw->done); + hw->fiq_inuse = 0; + if (s3c24xx_spi_usefiq(hw) && t->len >= 3) + s3c24xx_spi_tryfiq(hw); + /* send the first byte */ writeb(hw_txbyte(hw, 0), hw->regs + S3C2410_SPTDAT); wait_for_completion(&hw->done); - return hw->count; } @@ -254,17 +458,27 @@ static irqreturn_t s3c24xx_spi_irq(int irq, void *dev) goto irq_done; } - hw->count++; + if (!s3c24xx_spi_usingfiq(hw)) { + hw->count++; - if (hw->rx) - hw->rx[count] = readb(hw->regs + S3C2410_SPRDAT); + if (hw->rx) + hw->rx[count] = readb(hw->regs + S3C2410_SPRDAT); - count++; + count++; + + if (count < hw->len) + writeb(hw_txbyte(hw, count), hw->regs + S3C2410_SPTDAT); + else + complete(&hw->done); + } else { + hw->count = hw->len; + hw->fiq_inuse = 0; + + if (hw->rx) + hw->rx[hw->len-1] = readb(hw->regs + S3C2410_SPRDAT); - if (count < hw->len) - writeb(hw_txbyte(hw, count), hw->regs + S3C2410_SPTDAT); - else complete(&hw->done); + } irq_done: return IRQ_HANDLED; @@ -322,6 +536,10 @@ static int __init s3c24xx_spi_probe(struct platform_device *pdev) platform_set_drvdata(pdev, hw); init_completion(&hw->done); + /* initialise fiq handler */ + + s3c24xx_spi_initfiq(hw); + /* setup the master state. */ /* the spi->mode bits understood by this driver: */ diff --git a/drivers/spi/spi_s3c24xx_fiq.S b/drivers/spi/spi_s3c24xx_fiq.S new file mode 100644 index 000000000000..3793cae361db --- /dev/null +++ b/drivers/spi/spi_s3c24xx_fiq.S @@ -0,0 +1,116 @@ +/* linux/drivers/spi/spi_s3c24xx_fiq.S + * + * Copyright 2009 Simtec Electronics + * Ben Dooks + * + * S3C24XX SPI - FIQ pseudo-DMA transfer code + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include +#include + +#include +#include +#include + +#include "spi_s3c24xx_fiq.h" + + .text + + @ entry to these routines is as follows, with the register names + @ defined in fiq.h so that they can be shared with the C files which + @ setup the calling registers. + @ + @ fiq_rirq The base of the IRQ registers to find S3C2410_SRCPND + @ fiq_rtmp Temporary register to hold tx/rx data + @ fiq_rspi The base of the SPI register block + @ fiq_rtx The tx buffer pointer + @ fiq_rrx The rx buffer pointer + @ fiq_rcount The number of bytes to move + + @ each entry starts with a word entry of how long it is + @ and an offset to the irq acknowledgment word + +ENTRY(s3c24xx_spi_fiq_rx) +s3c24xx_spi_fix_rx: + .word fiq_rx_end - fiq_rx_start + .word fiq_rx_irq_ack - fiq_rx_start +fiq_rx_start: + ldr fiq_rtmp, fiq_rx_irq_ack + str fiq_rtmp, [ fiq_rirq, # S3C2410_SRCPND - S3C24XX_VA_IRQ ] + + ldrb fiq_rtmp, [ fiq_rspi, # S3C2410_SPRDAT ] + strb fiq_rtmp, [ fiq_rrx ], #1 + + mov fiq_rtmp, #0xff + strb fiq_rtmp, [ fiq_rspi, # S3C2410_SPTDAT ] + + subs fiq_rcount, fiq_rcount, #1 + subnes pc, lr, #4 @@ return, still have work to do + + @@ set IRQ controller so that next op will trigger IRQ + mov fiq_rtmp, #0 + str fiq_rtmp, [ fiq_rirq, # S3C2410_INTMOD - S3C24XX_VA_IRQ ] + subs pc, lr, #4 + +fiq_rx_irq_ack: + .word 0 +fiq_rx_end: + +ENTRY(s3c24xx_spi_fiq_txrx) +s3c24xx_spi_fiq_txrx: + .word fiq_txrx_end - fiq_txrx_start + .word fiq_txrx_irq_ack - fiq_txrx_start +fiq_txrx_start: + + ldrb fiq_rtmp, [ fiq_rspi, # S3C2410_SPRDAT ] + strb fiq_rtmp, [ fiq_rrx ], #1 + + ldr fiq_rtmp, fiq_txrx_irq_ack + str fiq_rtmp, [ fiq_rirq, # S3C2410_SRCPND - S3C24XX_VA_IRQ ] + + ldrb fiq_rtmp, [ fiq_rtx ], #1 + strb fiq_rtmp, [ fiq_rspi, # S3C2410_SPTDAT ] + + subs fiq_rcount, fiq_rcount, #1 + subnes pc, lr, #4 @@ return, still have work to do + + mov fiq_rtmp, #0 + str fiq_rtmp, [ fiq_rirq, # S3C2410_INTMOD - S3C24XX_VA_IRQ ] + subs pc, lr, #4 + +fiq_txrx_irq_ack: + .word 0 + +fiq_txrx_end: + +ENTRY(s3c24xx_spi_fiq_tx) +s3c24xx_spi_fix_tx: + .word fiq_tx_end - fiq_tx_start + .word fiq_tx_irq_ack - fiq_tx_start +fiq_tx_start: + ldrb fiq_rtmp, [ fiq_rspi, # S3C2410_SPRDAT ] + + ldr fiq_rtmp, fiq_tx_irq_ack + str fiq_rtmp, [ fiq_rirq, # S3C2410_SRCPND - S3C24XX_VA_IRQ ] + + ldrb fiq_rtmp, [ fiq_rtx ], #1 + strb fiq_rtmp, [ fiq_rspi, # S3C2410_SPTDAT ] + + subs fiq_rcount, fiq_rcount, #1 + subnes pc, lr, #4 @@ return, still have work to do + + mov fiq_rtmp, #0 + str fiq_rtmp, [ fiq_rirq, # S3C2410_INTMOD - S3C24XX_VA_IRQ ] + subs pc, lr, #4 + +fiq_tx_irq_ack: + .word 0 + +fiq_tx_end: + + .end diff --git a/drivers/spi/spi_s3c24xx_fiq.h b/drivers/spi/spi_s3c24xx_fiq.h new file mode 100644 index 000000000000..a5950bb25b51 --- /dev/null +++ b/drivers/spi/spi_s3c24xx_fiq.h @@ -0,0 +1,26 @@ +/* linux/drivers/spi/spi_s3c24xx_fiq.h + * + * Copyright 2009 Simtec Electronics + * Ben Dooks + * + * S3C24XX SPI - FIQ pseudo-DMA transfer support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/* We have R8 through R13 to play with */ + +#ifdef __ASSEMBLY__ +#define __REG_NR(x) r##x +#else +#define __REG_NR(x) (x) +#endif + +#define fiq_rspi __REG_NR(8) +#define fiq_rtmp __REG_NR(9) +#define fiq_rrx __REG_NR(10) +#define fiq_rtx __REG_NR(11) +#define fiq_rcount __REG_NR(12) +#define fiq_rirq __REG_NR(13) diff --git a/drivers/spi/spi_s3c64xx.c b/drivers/spi/spi_s3c64xx.c new file mode 100644 index 000000000000..88a456dba967 --- /dev/null +++ b/drivers/spi/spi_s3c64xx.c @@ -0,0 +1,1196 @@ +/* linux/drivers/spi/spi_s3c64xx.c + * + * Copyright (C) 2009 Samsung Electronics Ltd. + * Jaswinder Singh + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include + +/* Registers and bit-fields */ + +#define S3C64XX_SPI_CH_CFG 0x00 +#define S3C64XX_SPI_CLK_CFG 0x04 +#define S3C64XX_SPI_MODE_CFG 0x08 +#define S3C64XX_SPI_SLAVE_SEL 0x0C +#define S3C64XX_SPI_INT_EN 0x10 +#define S3C64XX_SPI_STATUS 0x14 +#define S3C64XX_SPI_TX_DATA 0x18 +#define S3C64XX_SPI_RX_DATA 0x1C +#define S3C64XX_SPI_PACKET_CNT 0x20 +#define S3C64XX_SPI_PENDING_CLR 0x24 +#define S3C64XX_SPI_SWAP_CFG 0x28 +#define S3C64XX_SPI_FB_CLK 0x2C + +#define S3C64XX_SPI_CH_HS_EN (1<<6) /* High Speed Enable */ +#define S3C64XX_SPI_CH_SW_RST (1<<5) +#define S3C64XX_SPI_CH_SLAVE (1<<4) +#define S3C64XX_SPI_CPOL_L (1<<3) +#define S3C64XX_SPI_CPHA_B (1<<2) +#define S3C64XX_SPI_CH_RXCH_ON (1<<1) +#define S3C64XX_SPI_CH_TXCH_ON (1<<0) + +#define S3C64XX_SPI_CLKSEL_SRCMSK (3<<9) +#define S3C64XX_SPI_CLKSEL_SRCSHFT 9 +#define S3C64XX_SPI_ENCLK_ENABLE (1<<8) +#define S3C64XX_SPI_PSR_MASK 0xff + +#define S3C64XX_SPI_MODE_CH_TSZ_BYTE (0<<29) +#define S3C64XX_SPI_MODE_CH_TSZ_HALFWORD (1<<29) +#define S3C64XX_SPI_MODE_CH_TSZ_WORD (2<<29) +#define S3C64XX_SPI_MODE_CH_TSZ_MASK (3<<29) +#define S3C64XX_SPI_MODE_BUS_TSZ_BYTE (0<<17) +#define S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD (1<<17) +#define S3C64XX_SPI_MODE_BUS_TSZ_WORD (2<<17) +#define S3C64XX_SPI_MODE_BUS_TSZ_MASK (3<<17) +#define S3C64XX_SPI_MODE_RXDMA_ON (1<<2) +#define S3C64XX_SPI_MODE_TXDMA_ON (1<<1) +#define S3C64XX_SPI_MODE_4BURST (1<<0) + +#define S3C64XX_SPI_SLAVE_AUTO (1<<1) +#define S3C64XX_SPI_SLAVE_SIG_INACT (1<<0) + +#define S3C64XX_SPI_ACT(c) writel(0, (c)->regs + S3C64XX_SPI_SLAVE_SEL) + +#define S3C64XX_SPI_DEACT(c) writel(S3C64XX_SPI_SLAVE_SIG_INACT, \ + (c)->regs + S3C64XX_SPI_SLAVE_SEL) + +#define S3C64XX_SPI_INT_TRAILING_EN (1<<6) +#define S3C64XX_SPI_INT_RX_OVERRUN_EN (1<<5) +#define S3C64XX_SPI_INT_RX_UNDERRUN_EN (1<<4) +#define S3C64XX_SPI_INT_TX_OVERRUN_EN (1<<3) +#define S3C64XX_SPI_INT_TX_UNDERRUN_EN (1<<2) +#define S3C64XX_SPI_INT_RX_FIFORDY_EN (1<<1) +#define S3C64XX_SPI_INT_TX_FIFORDY_EN (1<<0) + +#define S3C64XX_SPI_ST_RX_OVERRUN_ERR (1<<5) +#define S3C64XX_SPI_ST_RX_UNDERRUN_ERR (1<<4) +#define S3C64XX_SPI_ST_TX_OVERRUN_ERR (1<<3) +#define S3C64XX_SPI_ST_TX_UNDERRUN_ERR (1<<2) +#define S3C64XX_SPI_ST_RX_FIFORDY (1<<1) +#define S3C64XX_SPI_ST_TX_FIFORDY (1<<0) + +#define S3C64XX_SPI_PACKET_CNT_EN (1<<16) + +#define S3C64XX_SPI_PND_TX_UNDERRUN_CLR (1<<4) +#define S3C64XX_SPI_PND_TX_OVERRUN_CLR (1<<3) +#define S3C64XX_SPI_PND_RX_UNDERRUN_CLR (1<<2) +#define S3C64XX_SPI_PND_RX_OVERRUN_CLR (1<<1) +#define S3C64XX_SPI_PND_TRAILING_CLR (1<<0) + +#define S3C64XX_SPI_SWAP_RX_HALF_WORD (1<<7) +#define S3C64XX_SPI_SWAP_RX_BYTE (1<<6) +#define S3C64XX_SPI_SWAP_RX_BIT (1<<5) +#define S3C64XX_SPI_SWAP_RX_EN (1<<4) +#define S3C64XX_SPI_SWAP_TX_HALF_WORD (1<<3) +#define S3C64XX_SPI_SWAP_TX_BYTE (1<<2) +#define S3C64XX_SPI_SWAP_TX_BIT (1<<1) +#define S3C64XX_SPI_SWAP_TX_EN (1<<0) + +#define S3C64XX_SPI_FBCLK_MSK (3<<0) + +#define S3C64XX_SPI_ST_TRLCNTZ(v, i) ((((v) >> (i)->rx_lvl_offset) & \ + (((i)->fifo_lvl_mask + 1))) \ + ? 1 : 0) + +#define S3C64XX_SPI_ST_TX_DONE(v, i) ((((v) >> (i)->rx_lvl_offset) & \ + (((i)->fifo_lvl_mask + 1) << 1)) \ + ? 1 : 0) +#define TX_FIFO_LVL(v, i) (((v) >> 6) & (i)->fifo_lvl_mask) +#define RX_FIFO_LVL(v, i) (((v) >> (i)->rx_lvl_offset) & (i)->fifo_lvl_mask) + +#define S3C64XX_SPI_MAX_TRAILCNT 0x3ff +#define S3C64XX_SPI_TRAILCNT_OFF 19 + +#define S3C64XX_SPI_TRAILCNT S3C64XX_SPI_MAX_TRAILCNT + +#define msecs_to_loops(t) (loops_per_jiffy / 1000 * HZ * t) + +#define SUSPND (1<<0) +#define SPIBUSY (1<<1) +#define RXBUSY (1<<2) +#define TXBUSY (1<<3) + +/** + * struct s3c64xx_spi_driver_data - Runtime info holder for SPI driver. + * @clk: Pointer to the spi clock. + * @master: Pointer to the SPI Protocol master. + * @workqueue: Work queue for the SPI xfer requests. + * @cntrlr_info: Platform specific data for the controller this driver manages. + * @tgl_spi: Pointer to the last CS left untoggled by the cs_change hint. + * @work: Work + * @queue: To log SPI xfer requests. + * @lock: Controller specific lock. + * @state: Set of FLAGS to indicate status. + * @rx_dmach: Controller's DMA channel for Rx. + * @tx_dmach: Controller's DMA channel for Tx. + * @sfr_start: BUS address of SPI controller regs. + * @regs: Pointer to ioremap'ed controller registers. + * @xfer_completion: To indicate completion of xfer task. + * @cur_mode: Stores the active configuration of the controller. + * @cur_bpw: Stores the active bits per word settings. + * @cur_speed: Stores the active xfer clock speed. + */ +struct s3c64xx_spi_driver_data { + void __iomem *regs; + struct clk *clk; + struct platform_device *pdev; + struct spi_master *master; + struct workqueue_struct *workqueue; + struct s3c64xx_spi_cntrlr_info *cntrlr_info; + struct spi_device *tgl_spi; + struct work_struct work; + struct list_head queue; + spinlock_t lock; + enum dma_ch rx_dmach; + enum dma_ch tx_dmach; + unsigned long sfr_start; + struct completion xfer_completion; + unsigned state; + unsigned cur_mode, cur_bpw; + unsigned cur_speed; +}; + +static struct s3c2410_dma_client s3c64xx_spi_dma_client = { + .name = "samsung-spi-dma", +}; + +static void flush_fifo(struct s3c64xx_spi_driver_data *sdd) +{ + struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info; + void __iomem *regs = sdd->regs; + unsigned long loops; + u32 val; + + writel(0, regs + S3C64XX_SPI_PACKET_CNT); + + val = readl(regs + S3C64XX_SPI_CH_CFG); + val |= S3C64XX_SPI_CH_SW_RST; + val &= ~S3C64XX_SPI_CH_HS_EN; + writel(val, regs + S3C64XX_SPI_CH_CFG); + + /* Flush TxFIFO*/ + loops = msecs_to_loops(1); + do { + val = readl(regs + S3C64XX_SPI_STATUS); + } while (TX_FIFO_LVL(val, sci) && loops--); + + /* Flush RxFIFO*/ + loops = msecs_to_loops(1); + do { + val = readl(regs + S3C64XX_SPI_STATUS); + if (RX_FIFO_LVL(val, sci)) + readl(regs + S3C64XX_SPI_RX_DATA); + else + break; + } while (loops--); + + val = readl(regs + S3C64XX_SPI_CH_CFG); + val &= ~S3C64XX_SPI_CH_SW_RST; + writel(val, regs + S3C64XX_SPI_CH_CFG); + + val = readl(regs + S3C64XX_SPI_MODE_CFG); + val &= ~(S3C64XX_SPI_MODE_TXDMA_ON | S3C64XX_SPI_MODE_RXDMA_ON); + writel(val, regs + S3C64XX_SPI_MODE_CFG); + + val = readl(regs + S3C64XX_SPI_CH_CFG); + val &= ~(S3C64XX_SPI_CH_RXCH_ON | S3C64XX_SPI_CH_TXCH_ON); + writel(val, regs + S3C64XX_SPI_CH_CFG); +} + +static void enable_datapath(struct s3c64xx_spi_driver_data *sdd, + struct spi_device *spi, + struct spi_transfer *xfer, int dma_mode) +{ + struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info; + void __iomem *regs = sdd->regs; + u32 modecfg, chcfg; + + modecfg = readl(regs + S3C64XX_SPI_MODE_CFG); + modecfg &= ~(S3C64XX_SPI_MODE_TXDMA_ON | S3C64XX_SPI_MODE_RXDMA_ON); + + chcfg = readl(regs + S3C64XX_SPI_CH_CFG); + chcfg &= ~S3C64XX_SPI_CH_TXCH_ON; + + if (dma_mode) { + chcfg &= ~S3C64XX_SPI_CH_RXCH_ON; + } else { + /* Always shift in data in FIFO, even if xfer is Tx only, + * this helps setting PCKT_CNT value for generating clocks + * as exactly needed. + */ + chcfg |= S3C64XX_SPI_CH_RXCH_ON; + writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff) + | S3C64XX_SPI_PACKET_CNT_EN, + regs + S3C64XX_SPI_PACKET_CNT); + } + + if (xfer->tx_buf != NULL) { + sdd->state |= TXBUSY; + chcfg |= S3C64XX_SPI_CH_TXCH_ON; + if (dma_mode) { + modecfg |= S3C64XX_SPI_MODE_TXDMA_ON; + s3c2410_dma_config(sdd->tx_dmach, 1); + s3c2410_dma_enqueue(sdd->tx_dmach, (void *)sdd, + xfer->tx_dma, xfer->len); + s3c2410_dma_ctrl(sdd->tx_dmach, S3C2410_DMAOP_START); + } else { + unsigned char *buf = (unsigned char *) xfer->tx_buf; + int i = 0; + while (i < xfer->len) + writeb(buf[i++], regs + S3C64XX_SPI_TX_DATA); + } + } + + if (xfer->rx_buf != NULL) { + sdd->state |= RXBUSY; + + if (sci->high_speed && sdd->cur_speed >= 30000000UL + && !(sdd->cur_mode & SPI_CPHA)) + chcfg |= S3C64XX_SPI_CH_HS_EN; + + if (dma_mode) { + modecfg |= S3C64XX_SPI_MODE_RXDMA_ON; + chcfg |= S3C64XX_SPI_CH_RXCH_ON; + writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff) + | S3C64XX_SPI_PACKET_CNT_EN, + regs + S3C64XX_SPI_PACKET_CNT); + s3c2410_dma_config(sdd->rx_dmach, 1); + s3c2410_dma_enqueue(sdd->rx_dmach, (void *)sdd, + xfer->rx_dma, xfer->len); + s3c2410_dma_ctrl(sdd->rx_dmach, S3C2410_DMAOP_START); + } + } + + writel(modecfg, regs + S3C64XX_SPI_MODE_CFG); + writel(chcfg, regs + S3C64XX_SPI_CH_CFG); +} + +static inline void enable_cs(struct s3c64xx_spi_driver_data *sdd, + struct spi_device *spi) +{ + struct s3c64xx_spi_csinfo *cs; + + if (sdd->tgl_spi != NULL) { /* If last device toggled after mssg */ + if (sdd->tgl_spi != spi) { /* if last mssg on diff device */ + /* Deselect the last toggled device */ + cs = sdd->tgl_spi->controller_data; + cs->set_level(spi->mode & SPI_CS_HIGH ? 0 : 1); + } + sdd->tgl_spi = NULL; + } + + cs = spi->controller_data; + cs->set_level(spi->mode & SPI_CS_HIGH ? 1 : 0); +} + +static int wait_for_xfer(struct s3c64xx_spi_driver_data *sdd, + struct spi_transfer *xfer, int dma_mode) +{ + struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info; + void __iomem *regs = sdd->regs; + unsigned long val; + int ms; + + /* millisecs to xfer 'len' bytes @ 'cur_speed' */ + ms = xfer->len * 8 * 1000 / sdd->cur_speed; + ms += 5; /* some tolerance */ + + if (dma_mode) { + val = msecs_to_jiffies(ms) + 10; + val = wait_for_completion_timeout(&sdd->xfer_completion, val); + } else { + val = msecs_to_loops(ms); + do { + val = readl(regs + S3C64XX_SPI_STATUS); + } while (RX_FIFO_LVL(val, sci) < xfer->len && --val); + } + + if (!val) + return -EIO; + + if (dma_mode) { + u32 status; + + /* + * DmaTx returns after simply writing data in the FIFO, + * w/o waiting for real transmission on the bus to finish. + * DmaRx returns only after Dma read data from FIFO which + * needs bus transmission to finish, so we don't worry if + * Xfer involved Rx(with or without Tx). + */ + if (xfer->rx_buf == NULL) { + val = msecs_to_loops(10); + status = readl(regs + S3C64XX_SPI_STATUS); + while ((TX_FIFO_LVL(status, sci) + || !S3C64XX_SPI_ST_TX_DONE(status, sci)) + && --val) { + cpu_relax(); + status = readl(regs + S3C64XX_SPI_STATUS); + } + + if (!val) + return -EIO; + } + } else { + unsigned char *buf; + int i; + + /* If it was only Tx */ + if (xfer->rx_buf == NULL) { + sdd->state &= ~TXBUSY; + return 0; + } + + i = 0; + buf = xfer->rx_buf; + while (i < xfer->len) + buf[i++] = readb(regs + S3C64XX_SPI_RX_DATA); + + sdd->state &= ~RXBUSY; + } + + return 0; +} + +static inline void disable_cs(struct s3c64xx_spi_driver_data *sdd, + struct spi_device *spi) +{ + struct s3c64xx_spi_csinfo *cs = spi->controller_data; + + if (sdd->tgl_spi == spi) + sdd->tgl_spi = NULL; + + cs->set_level(spi->mode & SPI_CS_HIGH ? 0 : 1); +} + +static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd) +{ + struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info; + void __iomem *regs = sdd->regs; + u32 val; + + /* Disable Clock */ + val = readl(regs + S3C64XX_SPI_CLK_CFG); + val &= ~S3C64XX_SPI_ENCLK_ENABLE; + writel(val, regs + S3C64XX_SPI_CLK_CFG); + + /* Set Polarity and Phase */ + val = readl(regs + S3C64XX_SPI_CH_CFG); + val &= ~(S3C64XX_SPI_CH_SLAVE | + S3C64XX_SPI_CPOL_L | + S3C64XX_SPI_CPHA_B); + + if (sdd->cur_mode & SPI_CPOL) + val |= S3C64XX_SPI_CPOL_L; + + if (sdd->cur_mode & SPI_CPHA) + val |= S3C64XX_SPI_CPHA_B; + + writel(val, regs + S3C64XX_SPI_CH_CFG); + + /* Set Channel & DMA Mode */ + val = readl(regs + S3C64XX_SPI_MODE_CFG); + val &= ~(S3C64XX_SPI_MODE_BUS_TSZ_MASK + | S3C64XX_SPI_MODE_CH_TSZ_MASK); + + switch (sdd->cur_bpw) { + case 32: + val |= S3C64XX_SPI_MODE_BUS_TSZ_WORD; + break; + case 16: + val |= S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD; + break; + default: + val |= S3C64XX_SPI_MODE_BUS_TSZ_BYTE; + break; + } + val |= S3C64XX_SPI_MODE_CH_TSZ_BYTE; /* Always 8bits wide */ + + writel(val, regs + S3C64XX_SPI_MODE_CFG); + + /* Configure Clock */ + val = readl(regs + S3C64XX_SPI_CLK_CFG); + val &= ~S3C64XX_SPI_PSR_MASK; + val |= ((clk_get_rate(sci->src_clk) / sdd->cur_speed / 2 - 1) + & S3C64XX_SPI_PSR_MASK); + writel(val, regs + S3C64XX_SPI_CLK_CFG); + + /* Enable Clock */ + val = readl(regs + S3C64XX_SPI_CLK_CFG); + val |= S3C64XX_SPI_ENCLK_ENABLE; + writel(val, regs + S3C64XX_SPI_CLK_CFG); +} + +void s3c64xx_spi_dma_rxcb(struct s3c2410_dma_chan *chan, void *buf_id, + int size, enum s3c2410_dma_buffresult res) +{ + struct s3c64xx_spi_driver_data *sdd = buf_id; + unsigned long flags; + + spin_lock_irqsave(&sdd->lock, flags); + + if (res == S3C2410_RES_OK) + sdd->state &= ~RXBUSY; + else + dev_err(&sdd->pdev->dev, "DmaAbrtRx-%d\n", size); + + /* If the other done */ + if (!(sdd->state & TXBUSY)) + complete(&sdd->xfer_completion); + + spin_unlock_irqrestore(&sdd->lock, flags); +} + +void s3c64xx_spi_dma_txcb(struct s3c2410_dma_chan *chan, void *buf_id, + int size, enum s3c2410_dma_buffresult res) +{ + struct s3c64xx_spi_driver_data *sdd = buf_id; + unsigned long flags; + + spin_lock_irqsave(&sdd->lock, flags); + + if (res == S3C2410_RES_OK) + sdd->state &= ~TXBUSY; + else + dev_err(&sdd->pdev->dev, "DmaAbrtTx-%d \n", size); + + /* If the other done */ + if (!(sdd->state & RXBUSY)) + complete(&sdd->xfer_completion); + + spin_unlock_irqrestore(&sdd->lock, flags); +} + +#define XFER_DMAADDR_INVALID DMA_BIT_MASK(32) + +static int s3c64xx_spi_map_mssg(struct s3c64xx_spi_driver_data *sdd, + struct spi_message *msg) +{ + struct device *dev = &sdd->pdev->dev; + struct spi_transfer *xfer; + + if (msg->is_dma_mapped) + return 0; + + /* First mark all xfer unmapped */ + list_for_each_entry(xfer, &msg->transfers, transfer_list) { + xfer->rx_dma = XFER_DMAADDR_INVALID; + xfer->tx_dma = XFER_DMAADDR_INVALID; + } + + /* Map until end or first fail */ + list_for_each_entry(xfer, &msg->transfers, transfer_list) { + + if (xfer->tx_buf != NULL) { + xfer->tx_dma = dma_map_single(dev, xfer->tx_buf, + xfer->len, DMA_TO_DEVICE); + if (dma_mapping_error(dev, xfer->tx_dma)) { + dev_err(dev, "dma_map_single Tx failed\n"); + xfer->tx_dma = XFER_DMAADDR_INVALID; + return -ENOMEM; + } + } + + if (xfer->rx_buf != NULL) { + xfer->rx_dma = dma_map_single(dev, xfer->rx_buf, + xfer->len, DMA_FROM_DEVICE); + if (dma_mapping_error(dev, xfer->rx_dma)) { + dev_err(dev, "dma_map_single Rx failed\n"); + dma_unmap_single(dev, xfer->tx_dma, + xfer->len, DMA_TO_DEVICE); + xfer->tx_dma = XFER_DMAADDR_INVALID; + xfer->rx_dma = XFER_DMAADDR_INVALID; + return -ENOMEM; + } + } + } + + return 0; +} + +static void s3c64xx_spi_unmap_mssg(struct s3c64xx_spi_driver_data *sdd, + struct spi_message *msg) +{ + struct device *dev = &sdd->pdev->dev; + struct spi_transfer *xfer; + + if (msg->is_dma_mapped) + return; + + list_for_each_entry(xfer, &msg->transfers, transfer_list) { + + if (xfer->rx_buf != NULL + && xfer->rx_dma != XFER_DMAADDR_INVALID) + dma_unmap_single(dev, xfer->rx_dma, + xfer->len, DMA_FROM_DEVICE); + + if (xfer->tx_buf != NULL + && xfer->tx_dma != XFER_DMAADDR_INVALID) + dma_unmap_single(dev, xfer->tx_dma, + xfer->len, DMA_TO_DEVICE); + } +} + +static void handle_msg(struct s3c64xx_spi_driver_data *sdd, + struct spi_message *msg) +{ + struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info; + struct spi_device *spi = msg->spi; + struct s3c64xx_spi_csinfo *cs = spi->controller_data; + struct spi_transfer *xfer; + int status = 0, cs_toggle = 0; + u32 speed; + u8 bpw; + + /* If Master's(controller) state differs from that needed by Slave */ + if (sdd->cur_speed != spi->max_speed_hz + || sdd->cur_mode != spi->mode + || sdd->cur_bpw != spi->bits_per_word) { + sdd->cur_bpw = spi->bits_per_word; + sdd->cur_speed = spi->max_speed_hz; + sdd->cur_mode = spi->mode; + s3c64xx_spi_config(sdd); + } + + /* Map all the transfers if needed */ + if (s3c64xx_spi_map_mssg(sdd, msg)) { + dev_err(&spi->dev, + "Xfer: Unable to map message buffers!\n"); + status = -ENOMEM; + goto out; + } + + /* Configure feedback delay */ + writel(cs->fb_delay & 0x3, sdd->regs + S3C64XX_SPI_FB_CLK); + + list_for_each_entry(xfer, &msg->transfers, transfer_list) { + + unsigned long flags; + int use_dma; + + INIT_COMPLETION(sdd->xfer_completion); + + /* Only BPW and Speed may change across transfers */ + bpw = xfer->bits_per_word ? : spi->bits_per_word; + speed = xfer->speed_hz ? : spi->max_speed_hz; + + if (bpw != sdd->cur_bpw || speed != sdd->cur_speed) { + sdd->cur_bpw = bpw; + sdd->cur_speed = speed; + s3c64xx_spi_config(sdd); + } + + /* Polling method for xfers not bigger than FIFO capacity */ + if (xfer->len <= ((sci->fifo_lvl_mask >> 1) + 1)) + use_dma = 0; + else + use_dma = 1; + + spin_lock_irqsave(&sdd->lock, flags); + + /* Pending only which is to be done */ + sdd->state &= ~RXBUSY; + sdd->state &= ~TXBUSY; + + enable_datapath(sdd, spi, xfer, use_dma); + + /* Slave Select */ + enable_cs(sdd, spi); + + /* Start the signals */ + S3C64XX_SPI_ACT(sdd); + + spin_unlock_irqrestore(&sdd->lock, flags); + + status = wait_for_xfer(sdd, xfer, use_dma); + + /* Quiese the signals */ + S3C64XX_SPI_DEACT(sdd); + + if (status) { + dev_err(&spi->dev, "I/O Error: \ + rx-%d tx-%d res:rx-%c tx-%c len-%d\n", + xfer->rx_buf ? 1 : 0, xfer->tx_buf ? 1 : 0, + (sdd->state & RXBUSY) ? 'f' : 'p', + (sdd->state & TXBUSY) ? 'f' : 'p', + xfer->len); + + if (use_dma) { + if (xfer->tx_buf != NULL + && (sdd->state & TXBUSY)) + s3c2410_dma_ctrl(sdd->tx_dmach, + S3C2410_DMAOP_FLUSH); + if (xfer->rx_buf != NULL + && (sdd->state & RXBUSY)) + s3c2410_dma_ctrl(sdd->rx_dmach, + S3C2410_DMAOP_FLUSH); + } + + goto out; + } + + if (xfer->delay_usecs) + udelay(xfer->delay_usecs); + + if (xfer->cs_change) { + /* Hint that the next mssg is gonna be + for the same device */ + if (list_is_last(&xfer->transfer_list, + &msg->transfers)) + cs_toggle = 1; + else + disable_cs(sdd, spi); + } + + msg->actual_length += xfer->len; + + flush_fifo(sdd); + } + +out: + if (!cs_toggle || status) + disable_cs(sdd, spi); + else + sdd->tgl_spi = spi; + + s3c64xx_spi_unmap_mssg(sdd, msg); + + msg->status = status; + + if (msg->complete) + msg->complete(msg->context); +} + +static int acquire_dma(struct s3c64xx_spi_driver_data *sdd) +{ + if (s3c2410_dma_request(sdd->rx_dmach, + &s3c64xx_spi_dma_client, NULL) < 0) { + dev_err(&sdd->pdev->dev, "cannot get RxDMA\n"); + return 0; + } + s3c2410_dma_set_buffdone_fn(sdd->rx_dmach, s3c64xx_spi_dma_rxcb); + s3c2410_dma_devconfig(sdd->rx_dmach, S3C2410_DMASRC_HW, + sdd->sfr_start + S3C64XX_SPI_RX_DATA); + + if (s3c2410_dma_request(sdd->tx_dmach, + &s3c64xx_spi_dma_client, NULL) < 0) { + dev_err(&sdd->pdev->dev, "cannot get TxDMA\n"); + s3c2410_dma_free(sdd->rx_dmach, &s3c64xx_spi_dma_client); + return 0; + } + s3c2410_dma_set_buffdone_fn(sdd->tx_dmach, s3c64xx_spi_dma_txcb); + s3c2410_dma_devconfig(sdd->tx_dmach, S3C2410_DMASRC_MEM, + sdd->sfr_start + S3C64XX_SPI_TX_DATA); + + return 1; +} + +static void s3c64xx_spi_work(struct work_struct *work) +{ + struct s3c64xx_spi_driver_data *sdd = container_of(work, + struct s3c64xx_spi_driver_data, work); + unsigned long flags; + + /* Acquire DMA channels */ + while (!acquire_dma(sdd)) + msleep(10); + + spin_lock_irqsave(&sdd->lock, flags); + + while (!list_empty(&sdd->queue) + && !(sdd->state & SUSPND)) { + + struct spi_message *msg; + + msg = container_of(sdd->queue.next, struct spi_message, queue); + + list_del_init(&msg->queue); + + /* Set Xfer busy flag */ + sdd->state |= SPIBUSY; + + spin_unlock_irqrestore(&sdd->lock, flags); + + handle_msg(sdd, msg); + + spin_lock_irqsave(&sdd->lock, flags); + + sdd->state &= ~SPIBUSY; + } + + spin_unlock_irqrestore(&sdd->lock, flags); + + /* Free DMA channels */ + s3c2410_dma_free(sdd->tx_dmach, &s3c64xx_spi_dma_client); + s3c2410_dma_free(sdd->rx_dmach, &s3c64xx_spi_dma_client); +} + +static int s3c64xx_spi_transfer(struct spi_device *spi, + struct spi_message *msg) +{ + struct s3c64xx_spi_driver_data *sdd; + unsigned long flags; + + sdd = spi_master_get_devdata(spi->master); + + spin_lock_irqsave(&sdd->lock, flags); + + if (sdd->state & SUSPND) { + spin_unlock_irqrestore(&sdd->lock, flags); + return -ESHUTDOWN; + } + + msg->status = -EINPROGRESS; + msg->actual_length = 0; + + list_add_tail(&msg->queue, &sdd->queue); + + queue_work(sdd->workqueue, &sdd->work); + + spin_unlock_irqrestore(&sdd->lock, flags); + + return 0; +} + +/* + * Here we only check the validity of requested configuration + * and save the configuration in a local data-structure. + * The controller is actually configured only just before we + * get a message to transfer. + */ +static int s3c64xx_spi_setup(struct spi_device *spi) +{ + struct s3c64xx_spi_csinfo *cs = spi->controller_data; + struct s3c64xx_spi_driver_data *sdd; + struct s3c64xx_spi_cntrlr_info *sci; + struct spi_message *msg; + u32 psr, speed; + unsigned long flags; + int err = 0; + + if (cs == NULL || cs->set_level == NULL) { + dev_err(&spi->dev, "No CS for SPI(%d)\n", spi->chip_select); + return -ENODEV; + } + + sdd = spi_master_get_devdata(spi->master); + sci = sdd->cntrlr_info; + + spin_lock_irqsave(&sdd->lock, flags); + + list_for_each_entry(msg, &sdd->queue, queue) { + /* Is some mssg is already queued for this device */ + if (msg->spi == spi) { + dev_err(&spi->dev, + "setup: attempt while mssg in queue!\n"); + spin_unlock_irqrestore(&sdd->lock, flags); + return -EBUSY; + } + } + + if (sdd->state & SUSPND) { + spin_unlock_irqrestore(&sdd->lock, flags); + dev_err(&spi->dev, + "setup: SPI-%d not active!\n", spi->master->bus_num); + return -ESHUTDOWN; + } + + spin_unlock_irqrestore(&sdd->lock, flags); + + if (spi->bits_per_word != 8 + && spi->bits_per_word != 16 + && spi->bits_per_word != 32) { + dev_err(&spi->dev, "setup: %dbits/wrd not supported!\n", + spi->bits_per_word); + err = -EINVAL; + goto setup_exit; + } + + /* Check if we can provide the requested rate */ + speed = clk_get_rate(sci->src_clk) / 2 / (0 + 1); /* Max possible */ + + if (spi->max_speed_hz > speed) + spi->max_speed_hz = speed; + + psr = clk_get_rate(sci->src_clk) / 2 / spi->max_speed_hz - 1; + psr &= S3C64XX_SPI_PSR_MASK; + if (psr == S3C64XX_SPI_PSR_MASK) + psr--; + + speed = clk_get_rate(sci->src_clk) / 2 / (psr + 1); + if (spi->max_speed_hz < speed) { + if (psr+1 < S3C64XX_SPI_PSR_MASK) { + psr++; + } else { + err = -EINVAL; + goto setup_exit; + } + } + + speed = clk_get_rate(sci->src_clk) / 2 / (psr + 1); + if (spi->max_speed_hz >= speed) + spi->max_speed_hz = speed; + else + err = -EINVAL; + +setup_exit: + + /* setup() returns with device de-selected */ + disable_cs(sdd, spi); + + return err; +} + +static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd, int channel) +{ + struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info; + void __iomem *regs = sdd->regs; + unsigned int val; + + sdd->cur_speed = 0; + + S3C64XX_SPI_DEACT(sdd); + + /* Disable Interrupts - we use Polling if not DMA mode */ + writel(0, regs + S3C64XX_SPI_INT_EN); + + writel(sci->src_clk_nr << S3C64XX_SPI_CLKSEL_SRCSHFT, + regs + S3C64XX_SPI_CLK_CFG); + writel(0, regs + S3C64XX_SPI_MODE_CFG); + writel(0, regs + S3C64XX_SPI_PACKET_CNT); + + /* Clear any irq pending bits */ + writel(readl(regs + S3C64XX_SPI_PENDING_CLR), + regs + S3C64XX_SPI_PENDING_CLR); + + writel(0, regs + S3C64XX_SPI_SWAP_CFG); + + val = readl(regs + S3C64XX_SPI_MODE_CFG); + val &= ~S3C64XX_SPI_MODE_4BURST; + val &= ~(S3C64XX_SPI_MAX_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF); + val |= (S3C64XX_SPI_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF); + writel(val, regs + S3C64XX_SPI_MODE_CFG); + + flush_fifo(sdd); +} + +static int __init s3c64xx_spi_probe(struct platform_device *pdev) +{ + struct resource *mem_res, *dmatx_res, *dmarx_res; + struct s3c64xx_spi_driver_data *sdd; + struct s3c64xx_spi_cntrlr_info *sci; + struct spi_master *master; + int ret; + + if (pdev->id < 0) { + dev_err(&pdev->dev, + "Invalid platform device id-%d\n", pdev->id); + return -ENODEV; + } + + if (pdev->dev.platform_data == NULL) { + dev_err(&pdev->dev, "platform_data missing!\n"); + return -ENODEV; + } + + /* Check for availability of necessary resource */ + + dmatx_res = platform_get_resource(pdev, IORESOURCE_DMA, 0); + if (dmatx_res == NULL) { + dev_err(&pdev->dev, "Unable to get SPI-Tx dma resource\n"); + return -ENXIO; + } + + dmarx_res = platform_get_resource(pdev, IORESOURCE_DMA, 1); + if (dmarx_res == NULL) { + dev_err(&pdev->dev, "Unable to get SPI-Rx dma resource\n"); + return -ENXIO; + } + + mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (mem_res == NULL) { + dev_err(&pdev->dev, "Unable to get SPI MEM resource\n"); + return -ENXIO; + } + + master = spi_alloc_master(&pdev->dev, + sizeof(struct s3c64xx_spi_driver_data)); + if (master == NULL) { + dev_err(&pdev->dev, "Unable to allocate SPI Master\n"); + return -ENOMEM; + } + + sci = pdev->dev.platform_data; + + platform_set_drvdata(pdev, master); + + sdd = spi_master_get_devdata(master); + sdd->master = master; + sdd->cntrlr_info = sci; + sdd->pdev = pdev; + sdd->sfr_start = mem_res->start; + sdd->tx_dmach = dmatx_res->start; + sdd->rx_dmach = dmarx_res->start; + + sdd->cur_bpw = 8; + + master->bus_num = pdev->id; + master->setup = s3c64xx_spi_setup; + master->transfer = s3c64xx_spi_transfer; + master->num_chipselect = sci->num_cs; + master->dma_alignment = 8; + /* the spi->mode bits understood by this driver: */ + master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; + + if (request_mem_region(mem_res->start, + resource_size(mem_res), pdev->name) == NULL) { + dev_err(&pdev->dev, "Req mem region failed\n"); + ret = -ENXIO; + goto err0; + } + + sdd->regs = ioremap(mem_res->start, resource_size(mem_res)); + if (sdd->regs == NULL) { + dev_err(&pdev->dev, "Unable to remap IO\n"); + ret = -ENXIO; + goto err1; + } + + if (sci->cfg_gpio == NULL || sci->cfg_gpio(pdev)) { + dev_err(&pdev->dev, "Unable to config gpio\n"); + ret = -EBUSY; + goto err2; + } + + /* Setup clocks */ + sdd->clk = clk_get(&pdev->dev, "spi"); + if (IS_ERR(sdd->clk)) { + dev_err(&pdev->dev, "Unable to acquire clock 'spi'\n"); + ret = PTR_ERR(sdd->clk); + goto err3; + } + + if (clk_enable(sdd->clk)) { + dev_err(&pdev->dev, "Couldn't enable clock 'spi'\n"); + ret = -EBUSY; + goto err4; + } + + if (sci->src_clk_nr == S3C64XX_SPI_SRCCLK_PCLK) + sci->src_clk = sdd->clk; + else + sci->src_clk = clk_get(&pdev->dev, sci->src_clk_name); + if (IS_ERR(sci->src_clk)) { + dev_err(&pdev->dev, + "Unable to acquire clock '%s'\n", sci->src_clk_name); + ret = PTR_ERR(sci->src_clk); + goto err5; + } + + if (sci->src_clk != sdd->clk && clk_enable(sci->src_clk)) { + dev_err(&pdev->dev, "Couldn't enable clock '%s'\n", + sci->src_clk_name); + ret = -EBUSY; + goto err6; + } + + sdd->workqueue = create_singlethread_workqueue( + dev_name(master->dev.parent)); + if (sdd->workqueue == NULL) { + dev_err(&pdev->dev, "Unable to create workqueue\n"); + ret = -ENOMEM; + goto err7; + } + + /* Setup Deufult Mode */ + s3c64xx_spi_hwinit(sdd, pdev->id); + + spin_lock_init(&sdd->lock); + init_completion(&sdd->xfer_completion); + INIT_WORK(&sdd->work, s3c64xx_spi_work); + INIT_LIST_HEAD(&sdd->queue); + + if (spi_register_master(master)) { + dev_err(&pdev->dev, "cannot register SPI master\n"); + ret = -EBUSY; + goto err8; + } + + dev_dbg(&pdev->dev, "Samsung SoC SPI Driver loaded for Bus SPI-%d \ + with %d Slaves attached\n", + pdev->id, master->num_chipselect); + dev_dbg(&pdev->dev, "\tIOmem=[0x%x-0x%x]\ + \tDMA=[Rx-%d, Tx-%d]\n", + mem_res->end, mem_res->start, + sdd->rx_dmach, sdd->tx_dmach); + + return 0; + +err8: + destroy_workqueue(sdd->workqueue); +err7: + if (sci->src_clk != sdd->clk) + clk_disable(sci->src_clk); +err6: + if (sci->src_clk != sdd->clk) + clk_put(sci->src_clk); +err5: + clk_disable(sdd->clk); +err4: + clk_put(sdd->clk); +err3: +err2: + iounmap((void *) sdd->regs); +err1: + release_mem_region(mem_res->start, resource_size(mem_res)); +err0: + platform_set_drvdata(pdev, NULL); + spi_master_put(master); + + return ret; +} + +static int s3c64xx_spi_remove(struct platform_device *pdev) +{ + struct spi_master *master = spi_master_get(platform_get_drvdata(pdev)); + struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master); + struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info; + struct resource *mem_res; + unsigned long flags; + + spin_lock_irqsave(&sdd->lock, flags); + sdd->state |= SUSPND; + spin_unlock_irqrestore(&sdd->lock, flags); + + while (sdd->state & SPIBUSY) + msleep(10); + + spi_unregister_master(master); + + destroy_workqueue(sdd->workqueue); + + if (sci->src_clk != sdd->clk) + clk_disable(sci->src_clk); + + if (sci->src_clk != sdd->clk) + clk_put(sci->src_clk); + + clk_disable(sdd->clk); + clk_put(sdd->clk); + + iounmap((void *) sdd->regs); + + mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + release_mem_region(mem_res->start, resource_size(mem_res)); + + platform_set_drvdata(pdev, NULL); + spi_master_put(master); + + return 0; +} + +#ifdef CONFIG_PM +static int s3c64xx_spi_suspend(struct platform_device *pdev, pm_message_t state) +{ + struct spi_master *master = spi_master_get(platform_get_drvdata(pdev)); + struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master); + struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info; + struct s3c64xx_spi_csinfo *cs; + unsigned long flags; + + spin_lock_irqsave(&sdd->lock, flags); + sdd->state |= SUSPND; + spin_unlock_irqrestore(&sdd->lock, flags); + + while (sdd->state & SPIBUSY) + msleep(10); + + /* Disable the clock */ + if (sci->src_clk != sdd->clk) + clk_disable(sci->src_clk); + + clk_disable(sdd->clk); + + sdd->cur_speed = 0; /* Output Clock is stopped */ + + return 0; +} + +static int s3c64xx_spi_resume(struct platform_device *pdev) +{ + struct spi_master *master = spi_master_get(platform_get_drvdata(pdev)); + struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master); + struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info; + unsigned long flags; + + sci->cfg_gpio(pdev); + + /* Enable the clock */ + if (sci->src_clk != sdd->clk) + clk_enable(sci->src_clk); + + clk_enable(sdd->clk); + + s3c64xx_spi_hwinit(sdd, pdev->id); + + spin_lock_irqsave(&sdd->lock, flags); + sdd->state &= ~SUSPND; + spin_unlock_irqrestore(&sdd->lock, flags); + + return 0; +} +#else +#define s3c64xx_spi_suspend NULL +#define s3c64xx_spi_resume NULL +#endif /* CONFIG_PM */ + +static struct platform_driver s3c64xx_spi_driver = { + .driver = { + .name = "s3c64xx-spi", + .owner = THIS_MODULE, + }, + .remove = s3c64xx_spi_remove, + .suspend = s3c64xx_spi_suspend, + .resume = s3c64xx_spi_resume, +}; +MODULE_ALIAS("platform:s3c64xx-spi"); + +static int __init s3c64xx_spi_init(void) +{ + return platform_driver_probe(&s3c64xx_spi_driver, s3c64xx_spi_probe); +} +module_init(s3c64xx_spi_init); + +static void __exit s3c64xx_spi_exit(void) +{ + platform_driver_unregister(&s3c64xx_spi_driver); +} +module_exit(s3c64xx_spi_exit); + +MODULE_AUTHOR("Jaswinder Singh "); +MODULE_DESCRIPTION("S3C64XX SPI Controller Driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/spi/spi_sh_sci.c b/drivers/spi/spi_sh_sci.c index 7d36720eb982..a65c12ffa733 100644 --- a/drivers/spi/spi_sh_sci.c +++ b/drivers/spi/spi_sh_sci.c @@ -148,7 +148,7 @@ static int sh_sci_spi_probe(struct platform_device *dev) ret = -ENOENT; goto err1; } - sp->membase = ioremap(r->start, r->end - r->start + 1); + sp->membase = ioremap(r->start, resource_size(r)); if (!sp->membase) { ret = -ENXIO; goto err1; diff --git a/drivers/spi/spi_txx9.c b/drivers/spi/spi_txx9.c index 19f75627c3de..dfa024b633e1 100644 --- a/drivers/spi/spi_txx9.c +++ b/drivers/spi/spi_txx9.c @@ -375,12 +375,10 @@ static int __init txx9spi_probe(struct platform_device *dev) res = platform_get_resource(dev, IORESOURCE_MEM, 0); if (!res) goto exit_busy; - if (!devm_request_mem_region(&dev->dev, - res->start, res->end - res->start + 1, + if (!devm_request_mem_region(&dev->dev, res->start, resource_size(res), "spi_txx9")) goto exit_busy; - c->membase = devm_ioremap(&dev->dev, - res->start, res->end - res->start + 1); + c->membase = devm_ioremap(&dev->dev, res->start, resource_size(res)); if (!c->membase) goto exit_busy; diff --git a/drivers/spi/spidev.c b/drivers/spi/spidev.c index 9c446e6003d5..ea1bec3c9a13 100644 --- a/drivers/spi/spidev.c +++ b/drivers/spi/spidev.c @@ -53,7 +53,7 @@ #define SPIDEV_MAJOR 153 /* assigned */ #define N_SPI_MINORS 32 /* ... up to 256 */ -static unsigned long minors[N_SPI_MINORS / BITS_PER_LONG]; +static DECLARE_BITMAP(minors, N_SPI_MINORS); /* Bit masks for spi_device.mode management. Note that incorrect @@ -558,7 +558,7 @@ static struct class *spidev_class; /*-------------------------------------------------------------------------*/ -static int spidev_probe(struct spi_device *spi) +static int __devinit spidev_probe(struct spi_device *spi) { struct spidev_data *spidev; int status; @@ -607,7 +607,7 @@ static int spidev_probe(struct spi_device *spi) return status; } -static int spidev_remove(struct spi_device *spi) +static int __devexit spidev_remove(struct spi_device *spi) { struct spidev_data *spidev = spi_get_drvdata(spi); @@ -629,7 +629,7 @@ static int spidev_remove(struct spi_device *spi) return 0; } -static struct spi_driver spidev_spi = { +static struct spi_driver spidev_spi_driver = { .driver = { .name = "spidev", .owner = THIS_MODULE, @@ -661,14 +661,14 @@ static int __init spidev_init(void) spidev_class = class_create(THIS_MODULE, "spidev"); if (IS_ERR(spidev_class)) { - unregister_chrdev(SPIDEV_MAJOR, spidev_spi.driver.name); + unregister_chrdev(SPIDEV_MAJOR, spidev_spi_driver.driver.name); return PTR_ERR(spidev_class); } - status = spi_register_driver(&spidev_spi); + status = spi_register_driver(&spidev_spi_driver); if (status < 0) { class_destroy(spidev_class); - unregister_chrdev(SPIDEV_MAJOR, spidev_spi.driver.name); + unregister_chrdev(SPIDEV_MAJOR, spidev_spi_driver.driver.name); } return status; } @@ -676,9 +676,9 @@ module_init(spidev_init); static void __exit spidev_exit(void) { - spi_unregister_driver(&spidev_spi); + spi_unregister_driver(&spidev_spi_driver); class_destroy(spidev_class); - unregister_chrdev(SPIDEV_MAJOR, spidev_spi.driver.name); + unregister_chrdev(SPIDEV_MAJOR, spidev_spi_driver.driver.name); } module_exit(spidev_exit); diff --git a/include/linux/spi/dw_spi.h b/include/linux/spi/dw_spi.h new file mode 100644 index 000000000000..51b3e771a9a3 --- /dev/null +++ b/include/linux/spi/dw_spi.h @@ -0,0 +1,212 @@ +#ifndef DW_SPI_HEADER_H +#define DW_SPI_HEADER_H +#include + +/* Bit fields in CTRLR0 */ +#define SPI_DFS_OFFSET 0 + +#define SPI_FRF_OFFSET 4 +#define SPI_FRF_SPI 0x0 +#define SPI_FRF_SSP 0x1 +#define SPI_FRF_MICROWIRE 0x2 +#define SPI_FRF_RESV 0x3 + +#define SPI_MODE_OFFSET 6 +#define SPI_SCPH_OFFSET 6 +#define SPI_SCOL_OFFSET 7 +#define SPI_TMOD_OFFSET 8 +#define SPI_TMOD_TR 0x0 /* xmit & recv */ +#define SPI_TMOD_TO 0x1 /* xmit only */ +#define SPI_TMOD_RO 0x2 /* recv only */ +#define SPI_TMOD_EPROMREAD 0x3 /* eeprom read mode */ + +#define SPI_SLVOE_OFFSET 10 +#define SPI_SRL_OFFSET 11 +#define SPI_CFS_OFFSET 12 + +/* Bit fields in SR, 7 bits */ +#define SR_MASK 0x7f /* cover 7 bits */ +#define SR_BUSY (1 << 0) +#define SR_TF_NOT_FULL (1 << 1) +#define SR_TF_EMPT (1 << 2) +#define SR_RF_NOT_EMPT (1 << 3) +#define SR_RF_FULL (1 << 4) +#define SR_TX_ERR (1 << 5) +#define SR_DCOL (1 << 6) + +/* Bit fields in ISR, IMR, RISR, 7 bits */ +#define SPI_INT_TXEI (1 << 0) +#define SPI_INT_TXOI (1 << 1) +#define SPI_INT_RXUI (1 << 2) +#define SPI_INT_RXOI (1 << 3) +#define SPI_INT_RXFI (1 << 4) +#define SPI_INT_MSTI (1 << 5) + +/* TX RX interrupt level threshhold, max can be 256 */ +#define SPI_INT_THRESHOLD 32 + +enum dw_ssi_type { + SSI_MOTO_SPI = 0, + SSI_TI_SSP, + SSI_NS_MICROWIRE, +}; + +struct dw_spi_reg { + u32 ctrl0; + u32 ctrl1; + u32 ssienr; + u32 mwcr; + u32 ser; + u32 baudr; + u32 txfltr; + u32 rxfltr; + u32 txflr; + u32 rxflr; + u32 sr; + u32 imr; + u32 isr; + u32 risr; + u32 txoicr; + u32 rxoicr; + u32 rxuicr; + u32 msticr; + u32 icr; + u32 dmacr; + u32 dmatdlr; + u32 dmardlr; + u32 idr; + u32 version; + u32 dr; /* Currently oper as 32 bits, + though only low 16 bits matters */ +} __packed; + +struct dw_spi { + struct spi_master *master; + struct spi_device *cur_dev; + struct device *parent_dev; + enum dw_ssi_type type; + + void __iomem *regs; + unsigned long paddr; + u32 iolen; + int irq; + u32 max_freq; /* max bus freq supported */ + + u16 bus_num; + u16 num_cs; /* supported slave numbers */ + + /* Driver message queue */ + struct workqueue_struct *workqueue; + struct work_struct pump_messages; + spinlock_t lock; + struct list_head queue; + int busy; + int run; + + /* Message Transfer pump */ + struct tasklet_struct pump_transfers; + + /* Current message transfer state info */ + struct spi_message *cur_msg; + struct spi_transfer *cur_transfer; + struct chip_data *cur_chip; + struct chip_data *prev_chip; + size_t len; + void *tx; + void *tx_end; + void *rx; + void *rx_end; + int dma_mapped; + dma_addr_t rx_dma; + dma_addr_t tx_dma; + size_t rx_map_len; + size_t tx_map_len; + u8 n_bytes; /* current is a 1/2 bytes op */ + u8 max_bits_per_word; /* maxim is 16b */ + u32 dma_width; + int cs_change; + int (*write)(struct dw_spi *dws); + int (*read)(struct dw_spi *dws); + irqreturn_t (*transfer_handler)(struct dw_spi *dws); + void (*cs_control)(u32 command); + + /* Dma info */ + int dma_inited; + struct dma_chan *txchan; + struct dma_chan *rxchan; + int txdma_done; + int rxdma_done; + u64 tx_param; + u64 rx_param; + struct device *dma_dev; + dma_addr_t dma_addr; + + /* Bus interface info */ + void *priv; +#ifdef CONFIG_DEBUG_FS + struct dentry *debugfs; +#endif +}; + +#define dw_readl(dw, name) \ + __raw_readl(&(((struct dw_spi_reg *)dw->regs)->name)) +#define dw_writel(dw, name, val) \ + __raw_writel((val), &(((struct dw_spi_reg *)dw->regs)->name)) +#define dw_readw(dw, name) \ + __raw_readw(&(((struct dw_spi_reg *)dw->regs)->name)) +#define dw_writew(dw, name, val) \ + __raw_writew((val), &(((struct dw_spi_reg *)dw->regs)->name)) + +static inline void spi_enable_chip(struct dw_spi *dws, int enable) +{ + dw_writel(dws, ssienr, (enable ? 1 : 0)); +} + +static inline void spi_set_clk(struct dw_spi *dws, u16 div) +{ + dw_writel(dws, baudr, div); +} + +static inline void spi_chip_sel(struct dw_spi *dws, u16 cs) +{ + if (cs > dws->num_cs) + return; + dw_writel(dws, ser, 1 << cs); +} + +/* Disable IRQ bits */ +static inline void spi_mask_intr(struct dw_spi *dws, u32 mask) +{ + u32 new_mask; + + new_mask = dw_readl(dws, imr) & ~mask; + dw_writel(dws, imr, new_mask); +} + +/* Enable IRQ bits */ +static inline void spi_umask_intr(struct dw_spi *dws, u32 mask) +{ + u32 new_mask; + + new_mask = dw_readl(dws, imr) | mask; + dw_writel(dws, imr, new_mask); +} + +/* + * Each SPI slave device to work with dw_api controller should + * has such a structure claiming its working mode (PIO/DMA etc), + * which can be save in the "controller_data" member of the + * struct spi_device + */ +struct dw_spi_chip { + u8 poll_mode; /* 0 for contoller polling mode */ + u8 type; /* SPI/SSP/Micrwire */ + u8 enable_dma; + void (*cs_control)(u32 command); +}; + +extern int dw_spi_add_host(struct dw_spi *dws); +extern void dw_spi_remove_host(struct dw_spi *dws); +extern int dw_spi_suspend_host(struct dw_spi *dws); +extern int dw_spi_resume_host(struct dw_spi *dws); +#endif /* DW_SPI_HEADER_H */