2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-27 14:43:58 +08:00

UBI: Unsorted Block Images

UBI (Latin: "where?") manages multiple logical volumes on a single
flash device, specifically supporting NAND flash devices. UBI provides
a flexible partitioning concept which still allows for wear-levelling
across the whole flash device.

In a sense, UBI may be compared to the Logical Volume Manager
(LVM). Whereas LVM maps logical sector numbers to physical HDD sector
numbers, UBI maps logical eraseblocks to physical eraseblocks.

More information may be found at
http://www.linux-mtd.infradead.org/doc/ubi.html

Partitioning/Re-partitioning

  An UBI volume occupies a certain number of erase blocks. This is
  limited by a configured maximum volume size, which could also be
  viewed as the partition size. Each individual UBI volume's size can
  be changed independently of the other UBI volumes, provided that the
  sum of all volume sizes doesn't exceed a certain limit.

  UBI supports dynamic volumes and static volumes. Static volumes are
  read-only and their contents are protected by CRC check sums.

Bad eraseblocks handling

  UBI transparently handles bad eraseblocks. When a physical
  eraseblock becomes bad, it is substituted by a good physical
  eraseblock, and the user does not even notice this.

Scrubbing

  On a NAND flash bit flips can occur on any write operation,
  sometimes also on read. If bit flips persist on the device, at first
  they can still be corrected by ECC, but once they accumulate,
  correction will become impossible. Thus it is best to actively scrub
  the affected eraseblock, by first copying it to a free eraseblock
  and then erasing the original. The UBI layer performs this type of
  scrubbing under the covers, transparently to the UBI volume users.

Erase Counts

  UBI maintains an erase count header per eraseblock. This frees
  higher-level layers (like file systems) from doing this and allows
  for centralized erase count management instead. The erase counts are
  used by the wear-levelling algorithm in the UBI layer. The algorithm
  itself is exchangeable.

Booting from NAND

  For booting directly from NAND flash the hardware must at least be
  capable of fetching and executing a small portion of the NAND
  flash. Some NAND flash controllers have this kind of support. They
  usually limit the window to a few kilobytes in erase block 0. This
  "initial program loader" (IPL) must then contain sufficient logic to
  load and execute the next boot phase.

  Due to bad eraseblocks, which may be randomly scattered over the
  flash device, it is problematic to store the "secondary program
  loader" (SPL) statically. Also, due to bit-flips it may become
  corrupted over time. UBI allows to solve this problem gracefully by
  storing the SPL in a small static UBI volume.

UBI volumes vs. static partitions

  UBI volumes are still very similar to static MTD partitions:

    * both consist of eraseblocks (logical eraseblocks in case of UBI
      volumes, and physical eraseblocks in case of static partitions;
    * both support three basic operations - read, write, erase.

  But UBI volumes have the following advantages over traditional
  static MTD partitions:

    * there are no eraseblock wear-leveling constraints in case of UBI
      volumes, so the user should not care about this;
    * there are no bit-flips and bad eraseblocks in case of UBI volumes.

  So, UBI volumes may be considered as flash devices with relaxed
  restrictions.

Where can it be found?

  Documentation, kernel code and applications can be found in the MTD
  gits.

What are the applications for?

  The applications help to create binary flash images for two purposes: pfi
  files (partial flash images) for in-system update of UBI volumes, and plain
  binary images, with or without OOB data in case of NAND, for a manufacturing
  step. Furthermore some tools are/and will be created that allow flash content
  analysis after a system has crashed..

Who did UBI?

  The original ideas, where UBI is based on, were developed by Andreas
  Arnez, Frank Haverkamp and Thomas Gleixner. Josh W. Boyer and some others
  were involved too. The implementation of the kernel layer was done by Artem
  B. Bityutskiy. The user-space applications and tools were written by Oliver
  Lohmann with contributions from Frank Haverkamp, Andreas Arnez, and Artem.
  Joern Engel contributed a patch which modifies JFFS2 so that it can be run on
  a UBI volume. Thomas Gleixner did modifications to the NAND layer. Alexander
  Schmidt made some testing work as well as core functionality improvements.

Signed-off-by: Artem B. Bityutskiy <dedekind@linutronix.de>
Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>
This commit is contained in:
Artem B. Bityutskiy 2006-06-27 12:22:22 +04:00 committed by Frank Haverkamp
parent de46c33745
commit 801c135ce7
26 changed files with 12065 additions and 0 deletions

View File

@ -292,5 +292,7 @@ source "drivers/mtd/nand/Kconfig"
source "drivers/mtd/onenand/Kconfig"
source "drivers/mtd/ubi/Kconfig"
endmenu

View File

@ -28,3 +28,5 @@ nftl-objs := nftlcore.o nftlmount.o
inftl-objs := inftlcore.o inftlmount.o
obj-y += chips/ maps/ devices/ nand/ onenand/
obj-$(CONFIG_MTD_UBI) += ubi/

58
drivers/mtd/ubi/Kconfig Normal file
View File

@ -0,0 +1,58 @@
# drivers/mtd/ubi/Kconfig
menu "UBI - Unsorted block images"
depends on MTD
config MTD_UBI
tristate "Enable UBI"
depends on MTD
select CRC32
help
UBI is a software layer above MTD layer which admits of LVM-like
logical volumes on top of MTD devices, hides some complexities of
flash chips like wear and bad blocks and provides some other useful
capabilities. Please, consult the MTD web site for more details
(www.linux-mtd.infradead.org).
config MTD_UBI_WL_THRESHOLD
int "UBI wear-leveling threshold"
default 4096
range 2 65536
depends on MTD_UBI
help
This parameter defines the maximum difference between the highest
erase counter value and the lowest erase counter value of eraseblocks
of UBI devices. When this threshold is exceeded, UBI starts performing
wear leveling by means of moving data from eraseblock with low erase
counter to eraseblocks with high erase counter. Leave the default
value if unsure.
config MTD_UBI_BEB_RESERVE
int "Percentage of reserved eraseblocks for bad eraseblocks handling"
default 1
range 0 25
depends on MTD_UBI
help
If the MTD device admits of bad eraseblocks (e.g. NAND flash), UBI
reserves some amount of physical eraseblocks to handle new bad
eraseblocks. For example, if a flash physical eraseblock becomes bad,
UBI uses these reserved physical eraseblocks to relocate the bad one.
This option specifies how many physical eraseblocks will be reserved
for bad eraseblock handling (percents of total number of good flash
eraseblocks). If the underlying flash does not admit of bad
eraseblocks (e.g. NOR flash), this value is ignored and nothing is
reserved. Leave the default value if unsure.
config MTD_UBI_GLUEBI
bool "Emulate MTD devices"
default n
depends on MTD_UBI
help
This option enables MTD devices emulation on top of UBI volumes: for
each UBI volumes an MTD device is created, and all I/O to this MTD
device is redirected to the UBI volume. This is handy to make
MTD-oriented software (like JFFS2) work on top of UBI. Do not enable
this if no legacy software will be used.
source "drivers/mtd/ubi/Kconfig.debug"
endmenu

View File

@ -0,0 +1,104 @@
comment "UBI debugging options"
depends on MTD_UBI
config MTD_UBI_DEBUG
bool "UBI debugging"
depends on SYSFS
depends on MTD_UBI
select DEBUG_FS
select KALLSYMS_ALL
help
This option enables UBI debugging.
config MTD_UBI_DEBUG_MSG
bool "UBI debugging messages"
depends on MTD_UBI_DEBUG
default n
help
This option enables UBI debugging messages.
config MTD_UBI_DEBUG_PARANOID
bool "Extra self-checks"
default n
depends on MTD_UBI_DEBUG
help
This option enables extra checks in UBI code. Note this slows UBI down
significantly.
config MTD_UBI_DEBUG_DISABLE_BGT
bool "Do not enable the UBI background thread"
depends on MTD_UBI_DEBUG
default n
help
This option switches the background thread off by default. The thread
may be also be enabled/disabled via UBI sysfs.
config MTD_UBI_DEBUG_USERSPACE_IO
bool "Direct user-space write/erase support"
default n
depends on MTD_UBI_DEBUG
help
By default, users cannot directly write and erase individual
eraseblocks of dynamic volumes, and have to use update operation
instead. This option enables this capability - it is very useful for
debugging and testing.
config MTD_UBI_DEBUG_EMULATE_BITFLIPS
bool "Emulate flash bit-flips"
depends on MTD_UBI_DEBUG
default n
help
This option emulates bit-flips with probability 1/50, which in turn
causes scrubbing. Useful for debugging and stressing UBI.
config MTD_UBI_DEBUG_EMULATE_WRITE_FAILURES
bool "Emulate flash write failures"
depends on MTD_UBI_DEBUG
default n
help
This option emulates write failures with probability 1/100. Useful for
debugging and testing how UBI handlines errors.
config MTD_UBI_DEBUG_EMULATE_ERASE_FAILURES
bool "Emulate flash erase failures"
depends on MTD_UBI_DEBUG
default n
help
This option emulates erase failures with probability 1/100. Useful for
debugging and testing how UBI handlines errors.
menu "Additional UBI debugging messages"
depends on MTD_UBI_DEBUG
config MTD_UBI_DEBUG_MSG_BLD
bool "Additional UBI initialization and build messages"
default n
depends on MTD_UBI_DEBUG
help
This option enables detailed UBI initialization and device build
debugging messages.
config MTD_UBI_DEBUG_MSG_EBA
bool "Eraseblock association unit messages"
default n
depends on MTD_UBI_DEBUG
help
This option enables debugging messages from the UBI eraseblock
association unit.
config MTD_UBI_DEBUG_MSG_WL
bool "Wear-leveling unit messages"
default n
depends on MTD_UBI_DEBUG
help
This option enables debugging messages from the UBI wear-leveling
unit.
config MTD_UBI_DEBUG_MSG_IO
bool "Input/output unit messages"
default n
depends on MTD_UBI_DEBUG
help
This option enables debugging messages from the UBI input/output unit.
endmenu # UBI debugging messages

7
drivers/mtd/ubi/Makefile Normal file
View File

@ -0,0 +1,7 @@
obj-$(CONFIG_MTD_UBI) += ubi.o
ubi-y += vtbl.o vmt.o upd.o build.o cdev.o kapi.o eba.o io.o wl.o scan.o
ubi-y += misc.o
ubi-$(CONFIG_MTD_UBI_DEBUG) += debug.o
ubi-$(CONFIG_MTD_UBI_GLUEBI) += gluebi.o

848
drivers/mtd/ubi/build.c Normal file
View File

@ -0,0 +1,848 @@
/*
* Copyright (c) International Business Machines Corp., 2006
* Copyright (c) Nokia Corporation, 2007
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём),
* Frank Haverkamp
*/
/*
* This file includes UBI initialization and building of UBI devices. At the
* moment UBI devices may only be added while UBI is initialized, but dynamic
* device add/remove functionality is planned. Also, at the moment we only
* attach UBI devices by scanning, which will become a bottleneck when flashes
* reach certain large size. Then one may improve UBI and add other methods.
*/
#include <linux/err.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/stringify.h>
#include <linux/stat.h>
#include "ubi.h"
/* Maximum length of the 'mtd=' parameter */
#define MTD_PARAM_LEN_MAX 64
/**
* struct mtd_dev_param - MTD device parameter description data structure.
* @name: MTD device name or number string
* @vid_hdr_offs: VID header offset
* @data_offs: data offset
*/
struct mtd_dev_param
{
char name[MTD_PARAM_LEN_MAX];
int vid_hdr_offs;
int data_offs;
};
/* Numbers of elements set in the @mtd_dev_param array */
static int mtd_devs = 0;
/* MTD devices specification parameters */
static struct mtd_dev_param mtd_dev_param[UBI_MAX_DEVICES];
/* Number of UBI devices in system */
int ubi_devices_cnt;
/* All UBI devices in system */
struct ubi_device *ubi_devices[UBI_MAX_DEVICES];
/* Root UBI "class" object (corresponds to '/<sysfs>/class/ubi/') */
struct class *ubi_class;
/* "Show" method for files in '/<sysfs>/class/ubi/' */
static ssize_t ubi_version_show(struct class *class, char *buf)
{
return sprintf(buf, "%d\n", UBI_VERSION);
}
/* UBI version attribute ('/<sysfs>/class/ubi/version') */
static struct class_attribute ubi_version =
__ATTR(version, S_IRUGO, ubi_version_show, NULL);
static ssize_t dev_attribute_show(struct device *dev,
struct device_attribute *attr, char *buf);
/* UBI device attributes (correspond to files in '/<sysfs>/class/ubi/ubiX') */
static struct device_attribute dev_eraseblock_size =
__ATTR(eraseblock_size, S_IRUGO, dev_attribute_show, NULL);
static struct device_attribute dev_avail_eraseblocks =
__ATTR(avail_eraseblocks, S_IRUGO, dev_attribute_show, NULL);
static struct device_attribute dev_total_eraseblocks =
__ATTR(total_eraseblocks, S_IRUGO, dev_attribute_show, NULL);
static struct device_attribute dev_volumes_count =
__ATTR(volumes_count, S_IRUGO, dev_attribute_show, NULL);
static struct device_attribute dev_max_ec =
__ATTR(max_ec, S_IRUGO, dev_attribute_show, NULL);
static struct device_attribute dev_reserved_for_bad =
__ATTR(reserved_for_bad, S_IRUGO, dev_attribute_show, NULL);
static struct device_attribute dev_bad_peb_count =
__ATTR(bad_peb_count, S_IRUGO, dev_attribute_show, NULL);
static struct device_attribute dev_max_vol_count =
__ATTR(max_vol_count, S_IRUGO, dev_attribute_show, NULL);
static struct device_attribute dev_min_io_size =
__ATTR(min_io_size, S_IRUGO, dev_attribute_show, NULL);
static struct device_attribute dev_bgt_enabled =
__ATTR(bgt_enabled, S_IRUGO, dev_attribute_show, NULL);
/* "Show" method for files in '/<sysfs>/class/ubi/ubiX/' */
static ssize_t dev_attribute_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
const struct ubi_device *ubi;
ubi = container_of(dev, struct ubi_device, dev);
if (attr == &dev_eraseblock_size)
return sprintf(buf, "%d\n", ubi->leb_size);
else if (attr == &dev_avail_eraseblocks)
return sprintf(buf, "%d\n", ubi->avail_pebs);
else if (attr == &dev_total_eraseblocks)
return sprintf(buf, "%d\n", ubi->good_peb_count);
else if (attr == &dev_volumes_count)
return sprintf(buf, "%d\n", ubi->vol_count);
else if (attr == &dev_max_ec)
return sprintf(buf, "%d\n", ubi->max_ec);
else if (attr == &dev_reserved_for_bad)
return sprintf(buf, "%d\n", ubi->beb_rsvd_pebs);
else if (attr == &dev_bad_peb_count)
return sprintf(buf, "%d\n", ubi->bad_peb_count);
else if (attr == &dev_max_vol_count)
return sprintf(buf, "%d\n", ubi->vtbl_slots);
else if (attr == &dev_min_io_size)
return sprintf(buf, "%d\n", ubi->min_io_size);
else if (attr == &dev_bgt_enabled)
return sprintf(buf, "%d\n", ubi->thread_enabled);
else
BUG();
return 0;
}
/* Fake "release" method for UBI devices */
static void dev_release(struct device *dev) { }
/**
* ubi_sysfs_init - initialize sysfs for an UBI device.
* @ubi: UBI device description object
*
* This function returns zero in case of success and a negative error code in
* case of failure.
*/
static int ubi_sysfs_init(struct ubi_device *ubi)
{
int err;
ubi->dev.release = dev_release;
ubi->dev.devt = MKDEV(ubi->major, 0);
ubi->dev.class = ubi_class;
sprintf(&ubi->dev.bus_id[0], UBI_NAME_STR"%d", ubi->ubi_num);
err = device_register(&ubi->dev);
if (err)
goto out;
err = device_create_file(&ubi->dev, &dev_eraseblock_size);
if (err)
goto out_unregister;
err = device_create_file(&ubi->dev, &dev_avail_eraseblocks);
if (err)
goto out_eraseblock_size;
err = device_create_file(&ubi->dev, &dev_total_eraseblocks);
if (err)
goto out_avail_eraseblocks;
err = device_create_file(&ubi->dev, &dev_volumes_count);
if (err)
goto out_total_eraseblocks;
err = device_create_file(&ubi->dev, &dev_max_ec);
if (err)
goto out_volumes_count;
err = device_create_file(&ubi->dev, &dev_reserved_for_bad);
if (err)
goto out_volumes_max_ec;
err = device_create_file(&ubi->dev, &dev_bad_peb_count);
if (err)
goto out_reserved_for_bad;
err = device_create_file(&ubi->dev, &dev_max_vol_count);
if (err)
goto out_bad_peb_count;
err = device_create_file(&ubi->dev, &dev_min_io_size);
if (err)
goto out_max_vol_count;
err = device_create_file(&ubi->dev, &dev_bgt_enabled);
if (err)
goto out_min_io_size;
return 0;
out_min_io_size:
device_remove_file(&ubi->dev, &dev_min_io_size);
out_max_vol_count:
device_remove_file(&ubi->dev, &dev_max_vol_count);
out_bad_peb_count:
device_remove_file(&ubi->dev, &dev_bad_peb_count);
out_reserved_for_bad:
device_remove_file(&ubi->dev, &dev_reserved_for_bad);
out_volumes_max_ec:
device_remove_file(&ubi->dev, &dev_max_ec);
out_volumes_count:
device_remove_file(&ubi->dev, &dev_volumes_count);
out_total_eraseblocks:
device_remove_file(&ubi->dev, &dev_total_eraseblocks);
out_avail_eraseblocks:
device_remove_file(&ubi->dev, &dev_avail_eraseblocks);
out_eraseblock_size:
device_remove_file(&ubi->dev, &dev_eraseblock_size);
out_unregister:
device_unregister(&ubi->dev);
out:
ubi_err("failed to initialize sysfs for %s", ubi->ubi_name);
return err;
}
/**
* ubi_sysfs_close - close sysfs for an UBI device.
* @ubi: UBI device description object
*/
static void ubi_sysfs_close(struct ubi_device *ubi)
{
device_remove_file(&ubi->dev, &dev_bgt_enabled);
device_remove_file(&ubi->dev, &dev_min_io_size);
device_remove_file(&ubi->dev, &dev_max_vol_count);
device_remove_file(&ubi->dev, &dev_bad_peb_count);
device_remove_file(&ubi->dev, &dev_reserved_for_bad);
device_remove_file(&ubi->dev, &dev_max_ec);
device_remove_file(&ubi->dev, &dev_volumes_count);
device_remove_file(&ubi->dev, &dev_total_eraseblocks);
device_remove_file(&ubi->dev, &dev_avail_eraseblocks);
device_remove_file(&ubi->dev, &dev_eraseblock_size);
device_unregister(&ubi->dev);
}
/**
* kill_volumes - destroy all volumes.
* @ubi: UBI device description object
*/
static void kill_volumes(struct ubi_device *ubi)
{
int i;
for (i = 0; i < ubi->vtbl_slots; i++)
if (ubi->volumes[i])
ubi_free_volume(ubi, i);
}
/**
* uif_init - initialize user interfaces for an UBI device.
* @ubi: UBI device description object
*
* This function returns zero in case of success and a negative error code in
* case of failure.
*/
static int uif_init(struct ubi_device *ubi)
{
int i, err;
dev_t dev;
mutex_init(&ubi->vtbl_mutex);
spin_lock_init(&ubi->volumes_lock);
sprintf(ubi->ubi_name, UBI_NAME_STR "%d", ubi->ubi_num);
/*
* Major numbers for the UBI character devices are allocated
* dynamically. Major numbers of volume character devices are
* equivalent to ones of the corresponding UBI character device. Minor
* numbers of UBI character devices are 0, while minor numbers of
* volume character devices start from 1. Thus, we allocate one major
* number and ubi->vtbl_slots + 1 minor numbers.
*/
err = alloc_chrdev_region(&dev, 0, ubi->vtbl_slots + 1, ubi->ubi_name);
if (err) {
ubi_err("cannot register UBI character devices");
return err;
}
cdev_init(&ubi->cdev, &ubi_cdev_operations);
ubi->major = MAJOR(dev);
dbg_msg("%s major is %u", ubi->ubi_name, ubi->major);
ubi->cdev.owner = THIS_MODULE;
dev = MKDEV(ubi->major, 0);
err = cdev_add(&ubi->cdev, dev, 1);
if (err) {
ubi_err("cannot add character device %s", ubi->ubi_name);
goto out_unreg;
}
err = ubi_sysfs_init(ubi);
if (err)
goto out_cdev;
for (i = 0; i < ubi->vtbl_slots; i++)
if (ubi->volumes[i]) {
err = ubi_add_volume(ubi, i);
if (err)
goto out_volumes;
}
return 0;
out_volumes:
kill_volumes(ubi);
ubi_sysfs_close(ubi);
out_cdev:
cdev_del(&ubi->cdev);
out_unreg:
unregister_chrdev_region(MKDEV(ubi->major, 0),
ubi->vtbl_slots + 1);
return err;
}
/**
* uif_close - close user interfaces for an UBI device.
* @ubi: UBI device description object
*/
static void uif_close(struct ubi_device *ubi)
{
kill_volumes(ubi);
ubi_sysfs_close(ubi);
cdev_del(&ubi->cdev);
unregister_chrdev_region(MKDEV(ubi->major, 0), ubi->vtbl_slots + 1);
}
/**
* attach_by_scanning - attach an MTD device using scanning method.
* @ubi: UBI device descriptor
*
* This function returns zero in case of success and a negative error code in
* case of failure.
*
* Note, currently this is the only method to attach UBI devices. Hopefully in
* the future we'll have more scalable attaching methods and avoid full media
* scanning. But even in this case scanning will be needed as a fall-back
* attaching method if there are some on-flash table corruptions.
*/
static int attach_by_scanning(struct ubi_device *ubi)
{
int err;
struct ubi_scan_info *si;
si = ubi_scan(ubi);
if (IS_ERR(si))
return PTR_ERR(si);
ubi->bad_peb_count = si->bad_peb_count;
ubi->good_peb_count = ubi->peb_count - ubi->bad_peb_count;
ubi->max_ec = si->max_ec;
ubi->mean_ec = si->mean_ec;
err = ubi_read_volume_table(ubi, si);
if (err)
goto out_si;
err = ubi_wl_init_scan(ubi, si);
if (err)
goto out_vtbl;
err = ubi_eba_init_scan(ubi, si);
if (err)
goto out_wl;
ubi_scan_destroy_si(si);
return 0;
out_wl:
ubi_wl_close(ubi);
out_vtbl:
kfree(ubi->vtbl);
out_si:
ubi_scan_destroy_si(si);
return err;
}
/**
* io_init - initialize I/O unit for a given UBI device.
* @ubi: UBI device description object
*
* If @ubi->vid_hdr_offset or @ubi->leb_start is zero, default offsets are
* assumed:
* o EC header is always at offset zero - this cannot be changed;
* o VID header starts just after the EC header at the closest address
* aligned to @io->@hdrs_min_io_size;
* o data starts just after the VID header at the closest address aligned to
* @io->@min_io_size
*
* This function returns zero in case of success and a negative error code in
* case of failure.
*/
static int io_init(struct ubi_device *ubi)
{
if (ubi->mtd->numeraseregions != 0) {
/*
* Some flashes have several erase regions. Different regions
* may have different eraseblock size and other
* characteristics. It looks like mostly multi-region flashes
* have one "main" region and one or more small regions to
* store boot loader code or boot parameters or whatever. I
* guess we should just pick the largest region. But this is
* not implemented.
*/
ubi_err("multiple regions, not implemented");
return -EINVAL;
}
/*
* Note, in this implementation we support MTD devices with 0x7FFFFFFF
* physical eraseblocks maximum.
*/
ubi->peb_size = ubi->mtd->erasesize;
ubi->peb_count = ubi->mtd->size / ubi->mtd->erasesize;
ubi->flash_size = ubi->mtd->size;
if (ubi->mtd->block_isbad && ubi->mtd->block_markbad)
ubi->bad_allowed = 1;
ubi->min_io_size = ubi->mtd->writesize;
ubi->hdrs_min_io_size = ubi->mtd->writesize >> ubi->mtd->subpage_sft;
/* Make sure minimal I/O unit is power of 2 */
if (ubi->min_io_size == 0 ||
(ubi->min_io_size & (ubi->min_io_size - 1))) {
ubi_err("bad min. I/O unit");
return -EINVAL;
}
ubi_assert(ubi->hdrs_min_io_size > 0);
ubi_assert(ubi->hdrs_min_io_size <= ubi->min_io_size);
ubi_assert(ubi->min_io_size % ubi->hdrs_min_io_size == 0);
/* Calculate default aligned sizes of EC and VID headers */
ubi->ec_hdr_alsize = ALIGN(UBI_EC_HDR_SIZE, ubi->hdrs_min_io_size);
ubi->vid_hdr_alsize = ALIGN(UBI_VID_HDR_SIZE, ubi->hdrs_min_io_size);
dbg_msg("min_io_size %d", ubi->min_io_size);
dbg_msg("hdrs_min_io_size %d", ubi->hdrs_min_io_size);
dbg_msg("ec_hdr_alsize %d", ubi->ec_hdr_alsize);
dbg_msg("vid_hdr_alsize %d", ubi->vid_hdr_alsize);
if (ubi->vid_hdr_offset == 0)
/* Default offset */
ubi->vid_hdr_offset = ubi->vid_hdr_aloffset =
ubi->ec_hdr_alsize;
else {
ubi->vid_hdr_aloffset = ubi->vid_hdr_offset &
~(ubi->hdrs_min_io_size - 1);
ubi->vid_hdr_shift = ubi->vid_hdr_offset -
ubi->vid_hdr_aloffset;
}
/* Similar for the data offset */
if (ubi->leb_start == 0) {
ubi->leb_start = ubi->vid_hdr_offset + ubi->vid_hdr_alsize;
ubi->leb_start = ALIGN(ubi->leb_start, ubi->min_io_size);
}
dbg_msg("vid_hdr_offset %d", ubi->vid_hdr_offset);
dbg_msg("vid_hdr_aloffset %d", ubi->vid_hdr_aloffset);
dbg_msg("vid_hdr_shift %d", ubi->vid_hdr_shift);
dbg_msg("leb_start %d", ubi->leb_start);
/* The shift must be aligned to 32-bit boundary */
if (ubi->vid_hdr_shift % 4) {
ubi_err("unaligned VID header shift %d",
ubi->vid_hdr_shift);
return -EINVAL;
}
/* Check sanity */
if (ubi->vid_hdr_offset < UBI_EC_HDR_SIZE ||
ubi->leb_start < ubi->vid_hdr_offset + UBI_VID_HDR_SIZE ||
ubi->leb_start > ubi->peb_size - UBI_VID_HDR_SIZE ||
ubi->leb_start % ubi->min_io_size) {
ubi_err("bad VID header (%d) or data offsets (%d)",
ubi->vid_hdr_offset, ubi->leb_start);
return -EINVAL;
}
/*
* It may happen that EC and VID headers are situated in one minimal
* I/O unit. In this case we can only accept this UBI image in
* read-only mode.
*/
if (ubi->vid_hdr_offset + UBI_VID_HDR_SIZE <= ubi->hdrs_min_io_size) {
ubi_warn("EC and VID headers are in the same minimal I/O unit, "
"switch to read-only mode");
ubi->ro_mode = 1;
}
ubi->leb_size = ubi->peb_size - ubi->leb_start;
if (!(ubi->mtd->flags & MTD_WRITEABLE)) {
ubi_msg("MTD device %d is write-protected, attach in "
"read-only mode", ubi->mtd->index);
ubi->ro_mode = 1;
}
dbg_msg("leb_size %d", ubi->leb_size);
dbg_msg("ro_mode %d", ubi->ro_mode);
/*
* Note, ideally, we have to initialize ubi->bad_peb_count here. But
* unfortunately, MTD does not provide this information. We should loop
* over all physical eraseblocks and invoke mtd->block_is_bad() for
* each physical eraseblock. So, we skip ubi->bad_peb_count
* uninitialized and initialize it after scanning.
*/
return 0;
}
/**
* attach_mtd_dev - attach an MTD device.
* @mtd_dev: MTD device name or number string
* @vid_hdr_offset: VID header offset
* @data_offset: data offset
*
* This function attaches an MTD device to UBI. It first treats @mtd_dev as the
* MTD device name, and tries to open it by this name. If it is unable to open,
* it tries to convert @mtd_dev to an integer and open the MTD device by its
* number. Returns zero in case of success and a negative error code in case of
* failure.
*/
static int attach_mtd_dev(const char *mtd_dev, int vid_hdr_offset,
int data_offset)
{
struct ubi_device *ubi;
struct mtd_info *mtd;
int i, err;
mtd = get_mtd_device_nm(mtd_dev);
if (IS_ERR(mtd)) {
int mtd_num;
char *endp;
if (PTR_ERR(mtd) != -ENODEV)
return PTR_ERR(mtd);
/*
* Probably this is not MTD device name but MTD device number -
* check this out.
*/
mtd_num = simple_strtoul(mtd_dev, &endp, 0);
if (*endp != '\0' || mtd_dev == endp) {
ubi_err("incorrect MTD device: \"%s\"", mtd_dev);
return -ENODEV;
}
mtd = get_mtd_device(NULL, mtd_num);
if (IS_ERR(mtd))
return PTR_ERR(mtd);
}
/* Check if we already have the same MTD device attached */
for (i = 0; i < ubi_devices_cnt; i++)
if (ubi_devices[i]->mtd->index == mtd->index) {
ubi_err("mtd%d is already attached to ubi%d",
mtd->index, i);
err = -EINVAL;
goto out_mtd;
}
ubi = ubi_devices[ubi_devices_cnt] = kzalloc(sizeof(struct ubi_device),
GFP_KERNEL);
if (!ubi) {
err = -ENOMEM;
goto out_mtd;
}
ubi->ubi_num = ubi_devices_cnt;
ubi->mtd = mtd;
dbg_msg("attaching mtd%d to ubi%d: VID header offset %d data offset %d",
ubi->mtd->index, ubi_devices_cnt, vid_hdr_offset, data_offset);
ubi->vid_hdr_offset = vid_hdr_offset;
ubi->leb_start = data_offset;
err = io_init(ubi);
if (err)
goto out_free;
err = attach_by_scanning(ubi);
if (err) {
dbg_err("failed to attach by scanning, error %d", err);
goto out_free;
}
err = uif_init(ubi);
if (err)
goto out_detach;
ubi_devices_cnt += 1;
ubi_msg("attached mtd%d to ubi%d", ubi->mtd->index, ubi_devices_cnt);
ubi_msg("MTD device name: \"%s\"", ubi->mtd->name);
ubi_msg("MTD device size: %llu MiB", ubi->flash_size >> 20);
ubi_msg("physical eraseblock size: %d bytes (%d KiB)",
ubi->peb_size, ubi->peb_size >> 10);
ubi_msg("logical eraseblock size: %d bytes", ubi->leb_size);
ubi_msg("number of good PEBs: %d", ubi->good_peb_count);
ubi_msg("number of bad PEBs: %d", ubi->bad_peb_count);
ubi_msg("smallest flash I/O unit: %d", ubi->min_io_size);
ubi_msg("VID header offset: %d (aligned %d)",
ubi->vid_hdr_offset, ubi->vid_hdr_aloffset);
ubi_msg("data offset: %d", ubi->leb_start);
ubi_msg("max. allowed volumes: %d", ubi->vtbl_slots);
ubi_msg("wear-leveling threshold: %d", CONFIG_MTD_UBI_WL_THRESHOLD);
ubi_msg("number of internal volumes: %d", UBI_INT_VOL_COUNT);
ubi_msg("number of user volumes: %d",
ubi->vol_count - UBI_INT_VOL_COUNT);
ubi_msg("available PEBs: %d", ubi->avail_pebs);
ubi_msg("total number of reserved PEBs: %d", ubi->rsvd_pebs);
ubi_msg("number of PEBs reserved for bad PEB handling: %d",
ubi->beb_rsvd_pebs);
ubi_msg("max/mean erase counter: %d/%d", ubi->max_ec, ubi->mean_ec);
/* Enable the background thread */
if (!DBG_DISABLE_BGT) {
ubi->thread_enabled = 1;
wake_up_process(ubi->bgt_thread);
}
return 0;
out_detach:
ubi_eba_close(ubi);
ubi_wl_close(ubi);
kfree(ubi->vtbl);
out_free:
kfree(ubi);
out_mtd:
put_mtd_device(mtd);
ubi_devices[ubi_devices_cnt] = NULL;
return err;
}
/**
* detach_mtd_dev - detach an MTD device.
* @ubi: UBI device description object
*/
static void detach_mtd_dev(struct ubi_device *ubi)
{
int ubi_num = ubi->ubi_num, mtd_num = ubi->mtd->index;
dbg_msg("detaching mtd%d from ubi%d", ubi->mtd->index, ubi_num);
uif_close(ubi);
ubi_eba_close(ubi);
ubi_wl_close(ubi);
kfree(ubi->vtbl);
put_mtd_device(ubi->mtd);
kfree(ubi_devices[ubi_num]);
ubi_devices[ubi_num] = NULL;
ubi_devices_cnt -= 1;
ubi_assert(ubi_devices_cnt >= 0);
ubi_msg("mtd%d is detached from ubi%d", mtd_num, ubi_num);
}
static int __init ubi_init(void)
{
int err, i, k;
/* Ensure that EC and VID headers have correct size */
BUILD_BUG_ON(sizeof(struct ubi_ec_hdr) != 64);
BUILD_BUG_ON(sizeof(struct ubi_vid_hdr) != 64);
if (mtd_devs > UBI_MAX_DEVICES) {
printk("UBI error: too many MTD devices, maximum is %d\n",
UBI_MAX_DEVICES);
return -EINVAL;
}
ubi_class = class_create(THIS_MODULE, UBI_NAME_STR);
if (IS_ERR(ubi_class))
return PTR_ERR(ubi_class);
err = class_create_file(ubi_class, &ubi_version);
if (err)
goto out_class;
/* Attach MTD devices */
for (i = 0; i < mtd_devs; i++) {
struct mtd_dev_param *p = &mtd_dev_param[i];
cond_resched();
if (!p->name) {
dbg_err("empty name");
err = -EINVAL;
goto out_detach;
}
err = attach_mtd_dev(p->name, p->vid_hdr_offs, p->data_offs);
if (err)
goto out_detach;
}
return 0;
out_detach:
for (k = 0; k < i; k++)
detach_mtd_dev(ubi_devices[k]);
class_remove_file(ubi_class, &ubi_version);
out_class:
class_destroy(ubi_class);
return err;
}
module_init(ubi_init);
static void __exit ubi_exit(void)
{
int i, n = ubi_devices_cnt;
for (i = 0; i < n; i++)
detach_mtd_dev(ubi_devices[i]);
class_remove_file(ubi_class, &ubi_version);
class_destroy(ubi_class);
}
module_exit(ubi_exit);
/**
* bytes_str_to_int - convert a string representing number of bytes to an
* integer.
* @str: the string to convert
*
* This function returns positive resulting integer in case of success and a
* negative error code in case of failure.
*/
static int __init bytes_str_to_int(const char *str)
{
char *endp;
unsigned long result;
result = simple_strtoul(str, &endp, 0);
if (str == endp || result < 0) {
printk("UBI error: incorrect bytes count: \"%s\"\n", str);
return -EINVAL;
}
switch (*endp) {
case 'G':
result *= 1024;
case 'M':
result *= 1024;
case 'K':
case 'k':
result *= 1024;
if (endp[1] == 'i' && (endp[2] == '\0' ||
endp[2] == 'B' || endp[2] == 'b'))
endp += 2;
case '\0':
break;
default:
printk("UBI error: incorrect bytes count: \"%s\"\n", str);
return -EINVAL;
}
return result;
}
/**
* ubi_mtd_param_parse - parse the 'mtd=' UBI parameter.
* @val: the parameter value to parse
* @kp: not used
*
* This function returns zero in case of success and a negative error code in
* case of error.
*/
static int __init ubi_mtd_param_parse(const char *val, struct kernel_param *kp)
{
int i, len;
struct mtd_dev_param *p;
char buf[MTD_PARAM_LEN_MAX];
char *pbuf = &buf[0];
char *tokens[3] = {NULL, NULL, NULL};
if (mtd_devs == UBI_MAX_DEVICES) {
printk("UBI error: too many parameters, max. is %d\n",
UBI_MAX_DEVICES);
return -EINVAL;
}
len = strnlen(val, MTD_PARAM_LEN_MAX);
if (len == MTD_PARAM_LEN_MAX) {
printk("UBI error: parameter \"%s\" is too long, max. is %d\n",
val, MTD_PARAM_LEN_MAX);
return -EINVAL;
}
if (len == 0) {
printk("UBI warning: empty 'mtd=' parameter - ignored\n");
return 0;
}
strcpy(buf, val);
/* Get rid of the final newline */
if (buf[len - 1] == '\n')
buf[len - 1] = 0;
for (i = 0; i < 3; i++)
tokens[i] = strsep(&pbuf, ",");
if (pbuf) {
printk("UBI error: too many arguments at \"%s\"\n", val);
return -EINVAL;
}
if (tokens[0] == '\0')
return -EINVAL;
p = &mtd_dev_param[mtd_devs];
strcpy(&p->name[0], tokens[0]);
if (tokens[1])
p->vid_hdr_offs = bytes_str_to_int(tokens[1]);
if (tokens[2])
p->data_offs = bytes_str_to_int(tokens[2]);
if (p->vid_hdr_offs < 0)
return p->vid_hdr_offs;
if (p->data_offs < 0)
return p->data_offs;
mtd_devs += 1;
return 0;
}
module_param_call(mtd, ubi_mtd_param_parse, NULL, NULL, 000);
MODULE_PARM_DESC(mtd, "MTD devices to attach. Parameter format: "
"mtd=<name|num>[,<vid_hdr_offs>,<data_offs>]. "
"Multiple \"mtd\" parameters may be specified.\n"
"MTD devices may be specified by their number or name. "
"Optional \"vid_hdr_offs\" and \"data_offs\" parameters "
"specify UBI VID header position and data starting "
"position to be used by UBI.\n"
"Example: mtd=content,1984,2048 mtd=4 - attach MTD device"
"with name content using VID header offset 1984 and data "
"start 2048, and MTD device number 4 using default "
"offsets");
MODULE_VERSION(__stringify(UBI_VERSION));
MODULE_DESCRIPTION("UBI - Unsorted Block Images");
MODULE_AUTHOR("Artem Bityutskiy");
MODULE_LICENSE("GPL");

722
drivers/mtd/ubi/cdev.c Normal file
View File

@ -0,0 +1,722 @@
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*/
/*
* This file includes implementation of UBI character device operations.
*
* There are two kinds of character devices in UBI: UBI character devices and
* UBI volume character devices. UBI character devices allow users to
* manipulate whole volumes: create, remove, and re-size them. Volume character
* devices provide volume I/O capabilities.
*
* Major and minor numbers are assigned dynamically to both UBI and volume
* character devices.
*/
#include <linux/module.h>
#include <linux/stat.h>
#include <linux/ioctl.h>
#include <linux/capability.h>
#include <mtd/ubi-user.h>
#include <asm/uaccess.h>
#include <asm/div64.h>
#include "ubi.h"
/*
* Maximum sequence numbers of UBI and volume character device IOCTLs (direct
* logical eraseblock erase is a debug-only feature).
*/
#define UBI_CDEV_IOC_MAX_SEQ 2
#ifndef CONFIG_MTD_UBI_DEBUG_USERSPACE_IO
#define VOL_CDEV_IOC_MAX_SEQ 1
#else
#define VOL_CDEV_IOC_MAX_SEQ 2
#endif
/**
* major_to_device - get UBI device object by character device major number.
* @major: major number
*
* This function returns a pointer to the UBI device object.
*/
static struct ubi_device *major_to_device(int major)
{
int i;
for (i = 0; i < ubi_devices_cnt; i++)
if (ubi_devices[i] && ubi_devices[i]->major == major)
return ubi_devices[i];
BUG();
}
/**
* get_exclusive - get exclusive access to an UBI volume.
* @desc: volume descriptor
*
* This function changes UBI volume open mode to "exclusive". Returns previous
* mode value (positive integer) in case of success and a negative error code
* in case of failure.
*/
static int get_exclusive(struct ubi_volume_desc *desc)
{
int users, err;
struct ubi_volume *vol = desc->vol;
spin_lock(&vol->ubi->volumes_lock);
users = vol->readers + vol->writers + vol->exclusive;
ubi_assert(users > 0);
if (users > 1) {
dbg_err("%d users for volume %d", users, vol->vol_id);
err = -EBUSY;
} else {
vol->readers = vol->writers = 0;
vol->exclusive = 1;
err = desc->mode;
desc->mode = UBI_EXCLUSIVE;
}
spin_unlock(&vol->ubi->volumes_lock);
return err;
}
/**
* revoke_exclusive - revoke exclusive mode.
* @desc: volume descriptor
* @mode: new mode to switch to
*/
static void revoke_exclusive(struct ubi_volume_desc *desc, int mode)
{
struct ubi_volume *vol = desc->vol;
spin_lock(&vol->ubi->volumes_lock);
ubi_assert(vol->readers == 0 && vol->writers == 0);
ubi_assert(vol->exclusive == 1 && desc->mode == UBI_EXCLUSIVE);
vol->exclusive = 0;
if (mode == UBI_READONLY)
vol->readers = 1;
else if (mode == UBI_READWRITE)
vol->writers = 1;
else
vol->exclusive = 1;
spin_unlock(&vol->ubi->volumes_lock);
desc->mode = mode;
}
static int vol_cdev_open(struct inode *inode, struct file *file)
{
struct ubi_volume_desc *desc;
const struct ubi_device *ubi = major_to_device(imajor(inode));
int vol_id = iminor(inode) - 1;
int mode;
if (file->f_mode & FMODE_WRITE)
mode = UBI_READWRITE;
else
mode = UBI_READONLY;
dbg_msg("open volume %d, mode %d", vol_id, mode);
desc = ubi_open_volume(ubi->ubi_num, vol_id, mode);
if (IS_ERR(desc))
return PTR_ERR(desc);
file->private_data = desc;
return 0;
}
static int vol_cdev_release(struct inode *inode, struct file *file)
{
struct ubi_volume_desc *desc = file->private_data;
struct ubi_volume *vol = desc->vol;
dbg_msg("release volume %d, mode %d", vol->vol_id, desc->mode);
if (vol->updating) {
ubi_warn("update of volume %d not finished, volume is damaged",
vol->vol_id);
vol->updating = 0;
kfree(vol->upd_buf);
}
ubi_close_volume(desc);
return 0;
}
static loff_t vol_cdev_llseek(struct file *file, loff_t offset, int origin)
{
struct ubi_volume_desc *desc = file->private_data;
struct ubi_volume *vol = desc->vol;
loff_t new_offset;
if (vol->updating) {
/* Update is in progress, seeking is prohibited */
dbg_err("updating");
return -EBUSY;
}
switch (origin) {
case 0: /* SEEK_SET */
new_offset = offset;
break;
case 1: /* SEEK_CUR */
new_offset = file->f_pos + offset;
break;
case 2: /* SEEK_END */
new_offset = vol->used_bytes + offset;
break;
default:
return -EINVAL;
}
if (new_offset < 0 || new_offset > vol->used_bytes) {
dbg_err("bad seek %lld", new_offset);
return -EINVAL;
}
dbg_msg("seek volume %d, offset %lld, origin %d, new offset %lld",
vol->vol_id, offset, origin, new_offset);
file->f_pos = new_offset;
return new_offset;
}
static ssize_t vol_cdev_read(struct file *file, __user char *buf, size_t count,
loff_t *offp)
{
struct ubi_volume_desc *desc = file->private_data;
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
int err, lnum, off, len, vol_id = desc->vol->vol_id, tbuf_size;
size_t count_save = count;
void *tbuf;
uint64_t tmp;
dbg_msg("read %zd bytes from offset %lld of volume %d",
count, *offp, vol_id);
if (vol->updating) {
dbg_err("updating");
return -EBUSY;
}
if (vol->upd_marker) {
dbg_err("damaged volume, update marker is set");
return -EBADF;
}
if (*offp == vol->used_bytes || count == 0)
return 0;
if (vol->corrupted)
dbg_msg("read from corrupted volume %d", vol_id);
if (*offp + count > vol->used_bytes)
count_save = count = vol->used_bytes - *offp;
tbuf_size = vol->usable_leb_size;
if (count < tbuf_size)
tbuf_size = ALIGN(count, ubi->min_io_size);
tbuf = kmalloc(tbuf_size, GFP_KERNEL);
if (!tbuf)
return -ENOMEM;
len = count > tbuf_size ? tbuf_size : count;
tmp = *offp;
off = do_div(tmp, vol->usable_leb_size);
lnum = tmp;
do {
cond_resched();
if (off + len >= vol->usable_leb_size)
len = vol->usable_leb_size - off;
err = ubi_eba_read_leb(ubi, vol_id, lnum, tbuf, off, len, 0);
if (err)
break;
off += len;
if (off == vol->usable_leb_size) {
lnum += 1;
off -= vol->usable_leb_size;
}
count -= len;
*offp += len;
err = copy_to_user(buf, tbuf, len);
if (err) {
err = -EFAULT;
break;
}
buf += len;
len = count > tbuf_size ? tbuf_size : count;
} while (count);
kfree(tbuf);
return err ? err : count_save - count;
}
#ifdef CONFIG_MTD_UBI_DEBUG_USERSPACE_IO
/*
* This function allows to directly write to dynamic UBI volumes, without
* issuing the volume update operation. Available only as a debugging feature.
* Very useful for testing UBI.
*/
static ssize_t vol_cdev_direct_write(struct file *file, const char __user *buf,
size_t count, loff_t *offp)
{
struct ubi_volume_desc *desc = file->private_data;
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
int lnum, off, len, tbuf_size, vol_id = vol->vol_id, err = 0;
size_t count_save = count;
char *tbuf;
uint64_t tmp;
dbg_msg("requested: write %zd bytes to offset %lld of volume %u",
count, *offp, desc->vol->vol_id);
if (vol->vol_type == UBI_STATIC_VOLUME)
return -EROFS;
tmp = *offp;
off = do_div(tmp, vol->usable_leb_size);
lnum = tmp;
if (off % ubi->min_io_size) {
dbg_err("unaligned position");
return -EINVAL;
}
if (*offp + count > vol->used_bytes)
count_save = count = vol->used_bytes - *offp;
/* We can write only in fractions of the minimum I/O unit */
if (count % ubi->min_io_size) {
dbg_err("unaligned write length");
return -EINVAL;
}
tbuf_size = vol->usable_leb_size;
if (count < tbuf_size)
tbuf_size = ALIGN(count, ubi->min_io_size);
tbuf = kmalloc(tbuf_size, GFP_KERNEL);
if (!tbuf)
return -ENOMEM;
len = count > tbuf_size ? tbuf_size : count;
while (count) {
cond_resched();
if (off + len >= vol->usable_leb_size)
len = vol->usable_leb_size - off;
err = copy_from_user(tbuf, buf, len);
if (err) {
err = -EFAULT;
break;
}
err = ubi_eba_write_leb(ubi, vol_id, lnum, tbuf, off, len,
UBI_UNKNOWN);
if (err)
break;
off += len;
if (off == vol->usable_leb_size) {
lnum += 1;
off -= vol->usable_leb_size;
}
count -= len;
*offp += len;
buf += len;
len = count > tbuf_size ? tbuf_size : count;
}
kfree(tbuf);
return err ? err : count_save - count;
}
#else
#define vol_cdev_direct_write(file, buf, count, offp) -EPERM
#endif /* CONFIG_MTD_UBI_DEBUG_USERSPACE_IO */
static ssize_t vol_cdev_write(struct file *file, const char __user *buf,
size_t count, loff_t *offp)
{
int err = 0;
struct ubi_volume_desc *desc = file->private_data;
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
if (!vol->updating)
return vol_cdev_direct_write(file, buf, count, offp);
err = ubi_more_update_data(ubi, vol->vol_id, buf, count);
if (err < 0) {
ubi_err("cannot write %zd bytes of update data", count);
return err;
}
if (err) {
/*
* Update is finished, @err contains number of actually written
* bytes now.
*/
count = err;
err = ubi_check_volume(ubi, vol->vol_id);
if (err < 0)
return err;
if (err) {
ubi_warn("volume %d on UBI device %d is corrupted",
vol->vol_id, ubi->ubi_num);
vol->corrupted = 1;
}
vol->checked = 1;
revoke_exclusive(desc, UBI_READWRITE);
}
*offp += count;
return count;
}
static int vol_cdev_ioctl(struct inode *inode, struct file *file,
unsigned int cmd, unsigned long arg)
{
int err = 0;
struct ubi_volume_desc *desc = file->private_data;
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
void __user *argp = (void __user *)arg;
if (_IOC_NR(cmd) > VOL_CDEV_IOC_MAX_SEQ ||
_IOC_TYPE(cmd) != UBI_VOL_IOC_MAGIC)
return -ENOTTY;
if (_IOC_DIR(cmd) && _IOC_READ)
err = !access_ok(VERIFY_WRITE, argp, _IOC_SIZE(cmd));
else if (_IOC_DIR(cmd) && _IOC_WRITE)
err = !access_ok(VERIFY_READ, argp, _IOC_SIZE(cmd));
if (err)
return -EFAULT;
switch (cmd) {
/* Volume update command */
case UBI_IOCVOLUP:
{
int64_t bytes, rsvd_bytes;
if (!capable(CAP_SYS_RESOURCE)) {
err = -EPERM;
break;
}
err = copy_from_user(&bytes, argp, sizeof(int64_t));
if (err) {
err = -EFAULT;
break;
}
if (desc->mode == UBI_READONLY) {
err = -EROFS;
break;
}
rsvd_bytes = vol->reserved_pebs * (ubi->leb_size-vol->data_pad);
if (bytes < 0 || bytes > rsvd_bytes) {
err = -EINVAL;
break;
}
err = get_exclusive(desc);
if (err < 0)
break;
err = ubi_start_update(ubi, vol->vol_id, bytes);
if (bytes == 0)
revoke_exclusive(desc, UBI_READWRITE);
file->f_pos = 0;
break;
}
#ifdef CONFIG_MTD_UBI_DEBUG_USERSPACE_IO
/* Logical eraseblock erasure command */
case UBI_IOCEBER:
{
int32_t lnum;
err = __get_user(lnum, (__user int32_t *)argp);
if (err) {
err = -EFAULT;
break;
}
if (desc->mode == UBI_READONLY) {
err = -EROFS;
break;
}
if (lnum < 0 || lnum >= vol->reserved_pebs) {
err = -EINVAL;
break;
}
if (vol->vol_type != UBI_DYNAMIC_VOLUME) {
err = -EROFS;
break;
}
dbg_msg("erase LEB %d:%d", vol->vol_id, lnum);
err = ubi_eba_unmap_leb(ubi, vol->vol_id, lnum);
if (err)
break;
err = ubi_wl_flush(ubi);
break;
}
#endif
default:
err = -ENOTTY;
break;
}
return err;
}
/**
* verify_mkvol_req - verify volume creation request.
* @ubi: UBI device description object
* @req: the request to check
*
* This function zero if the request is correct, and %-EINVAL if not.
*/
static int verify_mkvol_req(const struct ubi_device *ubi,
const struct ubi_mkvol_req *req)
{
int n, err = -EINVAL;
if (req->bytes < 0 || req->alignment < 0 || req->vol_type < 0 ||
req->name_len < 0)
goto bad;
if ((req->vol_id < 0 || req->vol_id >= ubi->vtbl_slots) &&
req->vol_id != UBI_VOL_NUM_AUTO)
goto bad;
if (req->alignment == 0)
goto bad;
if (req->bytes == 0)
goto bad;
if (req->vol_type != UBI_DYNAMIC_VOLUME &&
req->vol_type != UBI_STATIC_VOLUME)
goto bad;
if (req->alignment > ubi->leb_size)
goto bad;
n = req->alignment % ubi->min_io_size;
if (req->alignment != 1 && n)
goto bad;
if (req->name_len > UBI_VOL_NAME_MAX) {
err = -ENAMETOOLONG;
goto bad;
}
return 0;
bad:
dbg_err("bad volume creation request");
ubi_dbg_dump_mkvol_req(req);
return err;
}
/**
* verify_rsvol_req - verify volume re-size request.
* @ubi: UBI device description object
* @req: the request to check
*
* This function returns zero if the request is correct, and %-EINVAL if not.
*/
static int verify_rsvol_req(const struct ubi_device *ubi,
const struct ubi_rsvol_req *req)
{
if (req->bytes <= 0)
return -EINVAL;
if (req->vol_id < 0 || req->vol_id >= ubi->vtbl_slots)
return -EINVAL;
return 0;
}
static int ubi_cdev_ioctl(struct inode *inode, struct file *file,
unsigned int cmd, unsigned long arg)
{
int err = 0;
struct ubi_device *ubi;
struct ubi_volume_desc *desc;
void __user *argp = (void __user *)arg;
if (_IOC_NR(cmd) > UBI_CDEV_IOC_MAX_SEQ ||
_IOC_TYPE(cmd) != UBI_IOC_MAGIC)
return -ENOTTY;
if (_IOC_DIR(cmd) && _IOC_READ)
err = !access_ok(VERIFY_WRITE, argp, _IOC_SIZE(cmd));
else if (_IOC_DIR(cmd) && _IOC_WRITE)
err = !access_ok(VERIFY_READ, argp, _IOC_SIZE(cmd));
if (err)
return -EFAULT;
if (!capable(CAP_SYS_RESOURCE))
return -EPERM;
ubi = major_to_device(imajor(inode));
if (IS_ERR(ubi))
return PTR_ERR(ubi);
switch (cmd) {
/* Create volume command */
case UBI_IOCMKVOL:
{
struct ubi_mkvol_req req;
dbg_msg("create volume");
err = __copy_from_user(&req, argp,
sizeof(struct ubi_mkvol_req));
if (err) {
err = -EFAULT;
break;
}
err = verify_mkvol_req(ubi, &req);
if (err)
break;
req.name[req.name_len] = '\0';
err = ubi_create_volume(ubi, &req);
if (err)
break;
err = __put_user(req.vol_id, (__user int32_t *)argp);
if (err)
err = -EFAULT;
break;
}
/* Remove volume command */
case UBI_IOCRMVOL:
{
int vol_id;
dbg_msg("remove volume");
err = __get_user(vol_id, (__user int32_t *)argp);
if (err) {
err = -EFAULT;
break;
}
desc = ubi_open_volume(ubi->ubi_num, vol_id, UBI_EXCLUSIVE);
if (IS_ERR(desc)) {
err = PTR_ERR(desc);
break;
}
err = ubi_remove_volume(desc);
if (err)
ubi_close_volume(desc);
break;
}
/* Re-size volume command */
case UBI_IOCRSVOL:
{
int pebs;
uint64_t tmp;
struct ubi_rsvol_req req;
dbg_msg("re-size volume");
err = __copy_from_user(&req, argp,
sizeof(struct ubi_rsvol_req));
if (err) {
err = -EFAULT;
break;
}
err = verify_rsvol_req(ubi, &req);
if (err)
break;
desc = ubi_open_volume(ubi->ubi_num, req.vol_id, UBI_EXCLUSIVE);
if (IS_ERR(desc)) {
err = PTR_ERR(desc);
break;
}
tmp = req.bytes;
pebs = !!do_div(tmp, desc->vol->usable_leb_size);
pebs += tmp;
err = ubi_resize_volume(desc, pebs);
ubi_close_volume(desc);
break;
}
default:
err = -ENOTTY;
break;
}
return err;
}
/* UBI character device operations */
struct file_operations ubi_cdev_operations = {
.owner = THIS_MODULE,
.ioctl = ubi_cdev_ioctl,
.llseek = no_llseek
};
/* UBI volume character device operations */
struct file_operations ubi_vol_cdev_operations = {
.owner = THIS_MODULE,
.open = vol_cdev_open,
.release = vol_cdev_release,
.llseek = vol_cdev_llseek,
.read = vol_cdev_read,
.write = vol_cdev_write,
.ioctl = vol_cdev_ioctl
};

224
drivers/mtd/ubi/debug.c Normal file
View File

@ -0,0 +1,224 @@
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*/
/*
* Here we keep all the UBI debugging stuff which should normally be disabled
* and compiled-out, but it is extremely helpful when hunting bugs or doing big
* changes.
*/
#ifdef CONFIG_MTD_UBI_DEBUG_MSG
#include "ubi.h"
/**
* ubi_dbg_dump_ec_hdr - dump an erase counter header.
* @ec_hdr: the erase counter header to dump
*/
void ubi_dbg_dump_ec_hdr(const struct ubi_ec_hdr *ec_hdr)
{
dbg_msg("erase counter header dump:");
dbg_msg("magic %#08x", ubi32_to_cpu(ec_hdr->magic));
dbg_msg("version %d", (int)ec_hdr->version);
dbg_msg("ec %llu", (long long)ubi64_to_cpu(ec_hdr->ec));
dbg_msg("vid_hdr_offset %d", ubi32_to_cpu(ec_hdr->vid_hdr_offset));
dbg_msg("data_offset %d", ubi32_to_cpu(ec_hdr->data_offset));
dbg_msg("hdr_crc %#08x", ubi32_to_cpu(ec_hdr->hdr_crc));
dbg_msg("erase counter header hexdump:");
ubi_dbg_hexdump(ec_hdr, UBI_EC_HDR_SIZE);
}
/**
* ubi_dbg_dump_vid_hdr - dump a volume identifier header.
* @vid_hdr: the volume identifier header to dump
*/
void ubi_dbg_dump_vid_hdr(const struct ubi_vid_hdr *vid_hdr)
{
dbg_msg("volume identifier header dump:");
dbg_msg("magic %08x", ubi32_to_cpu(vid_hdr->magic));
dbg_msg("version %d", (int)vid_hdr->version);
dbg_msg("vol_type %d", (int)vid_hdr->vol_type);
dbg_msg("copy_flag %d", (int)vid_hdr->copy_flag);
dbg_msg("compat %d", (int)vid_hdr->compat);
dbg_msg("vol_id %d", ubi32_to_cpu(vid_hdr->vol_id));
dbg_msg("lnum %d", ubi32_to_cpu(vid_hdr->lnum));
dbg_msg("leb_ver %u", ubi32_to_cpu(vid_hdr->leb_ver));
dbg_msg("data_size %d", ubi32_to_cpu(vid_hdr->data_size));
dbg_msg("used_ebs %d", ubi32_to_cpu(vid_hdr->used_ebs));
dbg_msg("data_pad %d", ubi32_to_cpu(vid_hdr->data_pad));
dbg_msg("sqnum %llu",
(unsigned long long)ubi64_to_cpu(vid_hdr->sqnum));
dbg_msg("hdr_crc %08x", ubi32_to_cpu(vid_hdr->hdr_crc));
dbg_msg("volume identifier header hexdump:");
}
/**
* ubi_dbg_dump_vol_info- dump volume information.
* @vol: UBI volume description object
*/
void ubi_dbg_dump_vol_info(const struct ubi_volume *vol)
{
dbg_msg("volume information dump:");
dbg_msg("vol_id %d", vol->vol_id);
dbg_msg("reserved_pebs %d", vol->reserved_pebs);
dbg_msg("alignment %d", vol->alignment);
dbg_msg("data_pad %d", vol->data_pad);
dbg_msg("vol_type %d", vol->vol_type);
dbg_msg("name_len %d", vol->name_len);
dbg_msg("usable_leb_size %d", vol->usable_leb_size);
dbg_msg("used_ebs %d", vol->used_ebs);
dbg_msg("used_bytes %lld", vol->used_bytes);
dbg_msg("last_eb_bytes %d", vol->last_eb_bytes);
dbg_msg("corrupted %d", vol->corrupted);
dbg_msg("upd_marker %d", vol->upd_marker);
if (vol->name_len <= UBI_VOL_NAME_MAX &&
strnlen(vol->name, vol->name_len + 1) == vol->name_len) {
dbg_msg("name %s", vol->name);
} else {
dbg_msg("the 1st 5 characters of the name: %c%c%c%c%c",
vol->name[0], vol->name[1], vol->name[2],
vol->name[3], vol->name[4]);
}
}
/**
* ubi_dbg_dump_vtbl_record - dump a &struct ubi_vtbl_record object.
* @r: the object to dump
* @idx: volume table index
*/
void ubi_dbg_dump_vtbl_record(const struct ubi_vtbl_record *r, int idx)
{
int name_len = ubi16_to_cpu(r->name_len);
dbg_msg("volume table record %d dump:", idx);
dbg_msg("reserved_pebs %d", ubi32_to_cpu(r->reserved_pebs));
dbg_msg("alignment %d", ubi32_to_cpu(r->alignment));
dbg_msg("data_pad %d", ubi32_to_cpu(r->data_pad));
dbg_msg("vol_type %d", (int)r->vol_type);
dbg_msg("upd_marker %d", (int)r->upd_marker);
dbg_msg("name_len %d", name_len);
if (r->name[0] == '\0') {
dbg_msg("name NULL");
return;
}
if (name_len <= UBI_VOL_NAME_MAX &&
strnlen(&r->name[0], name_len + 1) == name_len) {
dbg_msg("name %s", &r->name[0]);
} else {
dbg_msg("1st 5 characters of the name: %c%c%c%c%c",
r->name[0], r->name[1], r->name[2], r->name[3],
r->name[4]);
}
dbg_msg("crc %#08x", ubi32_to_cpu(r->crc));
}
/**
* ubi_dbg_dump_sv - dump a &struct ubi_scan_volume object.
* @sv: the object to dump
*/
void ubi_dbg_dump_sv(const struct ubi_scan_volume *sv)
{
dbg_msg("volume scanning information dump:");
dbg_msg("vol_id %d", sv->vol_id);
dbg_msg("highest_lnum %d", sv->highest_lnum);
dbg_msg("leb_count %d", sv->leb_count);
dbg_msg("compat %d", sv->compat);
dbg_msg("vol_type %d", sv->vol_type);
dbg_msg("used_ebs %d", sv->used_ebs);
dbg_msg("last_data_size %d", sv->last_data_size);
dbg_msg("data_pad %d", sv->data_pad);
}
/**
* ubi_dbg_dump_seb - dump a &struct ubi_scan_leb object.
* @seb: the object to dump
* @type: object type: 0 - not corrupted, 1 - corrupted
*/
void ubi_dbg_dump_seb(const struct ubi_scan_leb *seb, int type)
{
dbg_msg("eraseblock scanning information dump:");
dbg_msg("ec %d", seb->ec);
dbg_msg("pnum %d", seb->pnum);
if (type == 0) {
dbg_msg("lnum %d", seb->lnum);
dbg_msg("scrub %d", seb->scrub);
dbg_msg("sqnum %llu", seb->sqnum);
dbg_msg("leb_ver %u", seb->leb_ver);
}
}
/**
* ubi_dbg_dump_mkvol_req - dump a &struct ubi_mkvol_req object.
* @req: the object to dump
*/
void ubi_dbg_dump_mkvol_req(const struct ubi_mkvol_req *req)
{
char nm[17];
dbg_msg("volume creation request dump:");
dbg_msg("vol_id %d", req->vol_id);
dbg_msg("alignment %d", req->alignment);
dbg_msg("bytes %lld", (long long)req->bytes);
dbg_msg("vol_type %d", req->vol_type);
dbg_msg("name_len %d", req->name_len);
memcpy(nm, req->name, 16);
nm[16] = 0;
dbg_msg("the 1st 16 characters of the name: %s", nm);
}
#define BYTES_PER_LINE 32
/**
* ubi_dbg_hexdump - dump a buffer.
* @ptr: the buffer to dump
* @size: buffer size which must be multiple of 4 bytes
*/
void ubi_dbg_hexdump(const void *ptr, int size)
{
int i, k = 0, rows, columns;
const uint8_t *p = ptr;
size = ALIGN(size, 4);
rows = size/BYTES_PER_LINE + size % BYTES_PER_LINE;
for (i = 0; i < rows; i++) {
int j;
cond_resched();
columns = min(size - k, BYTES_PER_LINE) / 4;
if (columns == 0)
break;
printk(KERN_DEBUG "%5d: ", i * BYTES_PER_LINE);
for (j = 0; j < columns; j++) {
int n, N;
N = size - k > 4 ? 4 : size - k;
for (n = 0; n < N; n++)
printk("%02x", p[k++]);
printk(" ");
}
printk("\n");
}
}
#endif /* CONFIG_MTD_UBI_DEBUG_MSG */

161
drivers/mtd/ubi/debug.h Normal file
View File

@ -0,0 +1,161 @@
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*/
#ifndef __UBI_DEBUG_H__
#define __UBI_DEBUG_H__
#ifdef CONFIG_MTD_UBI_DEBUG
#include <linux/random.h>
#define ubi_assert(expr) BUG_ON(!(expr))
#define dbg_err(fmt, ...) ubi_err(fmt, ##__VA_ARGS__)
#else
#define ubi_assert(expr) ({})
#define dbg_err(fmt, ...) ({})
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_DISABLE_BGT
#define DBG_DISABLE_BGT 1
#else
#define DBG_DISABLE_BGT 0
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_MSG
/* Generic debugging message */
#define dbg_msg(fmt, ...) \
printk(KERN_DEBUG "UBI DBG: %s: " fmt "\n", __FUNCTION__, ##__VA_ARGS__)
#define ubi_dbg_dump_stack() dump_stack()
struct ubi_ec_hdr;
struct ubi_vid_hdr;
struct ubi_volume;
struct ubi_vtbl_record;
struct ubi_scan_volume;
struct ubi_scan_leb;
struct ubi_mkvol_req;
void ubi_dbg_print(int type, const char *func, const char *fmt, ...);
void ubi_dbg_dump_ec_hdr(const struct ubi_ec_hdr *ec_hdr);
void ubi_dbg_dump_vid_hdr(const struct ubi_vid_hdr *vid_hdr);
void ubi_dbg_dump_vol_info(const struct ubi_volume *vol);
void ubi_dbg_dump_vtbl_record(const struct ubi_vtbl_record *r, int idx);
void ubi_dbg_dump_sv(const struct ubi_scan_volume *sv);
void ubi_dbg_dump_seb(const struct ubi_scan_leb *seb, int type);
void ubi_dbg_dump_mkvol_req(const struct ubi_mkvol_req *req);
void ubi_dbg_hexdump(const void *buf, int size);
#else
#define dbg_msg(fmt, ...) ({})
#define ubi_dbg_dump_stack() ({})
#define ubi_dbg_print(func, fmt, ...) ({})
#define ubi_dbg_dump_ec_hdr(ec_hdr) ({})
#define ubi_dbg_dump_vid_hdr(vid_hdr) ({})
#define ubi_dbg_dump_vol_info(vol) ({})
#define ubi_dbg_dump_vtbl_record(r, idx) ({})
#define ubi_dbg_dump_sv(sv) ({})
#define ubi_dbg_dump_seb(seb, type) ({})
#define ubi_dbg_dump_mkvol_req(req) ({})
#define ubi_dbg_hexdump(buf, size) ({})
#endif /* CONFIG_MTD_UBI_DEBUG_MSG */
#ifdef CONFIG_MTD_UBI_DEBUG_MSG_EBA
/* Messages from the eraseblock association unit */
#define dbg_eba(fmt, ...) \
printk(KERN_DEBUG "UBI DBG eba: %s: " fmt "\n", __FUNCTION__, \
##__VA_ARGS__)
#else
#define dbg_eba(fmt, ...) ({})
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_MSG_WL
/* Messages from the wear-leveling unit */
#define dbg_wl(fmt, ...) \
printk(KERN_DEBUG "UBI DBG wl: %s: " fmt "\n", __FUNCTION__, \
##__VA_ARGS__)
#else
#define dbg_wl(fmt, ...) ({})
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_MSG_IO
/* Messages from the input/output unit */
#define dbg_io(fmt, ...) \
printk(KERN_DEBUG "UBI DBG io: %s: " fmt "\n", __FUNCTION__, \
##__VA_ARGS__)
#else
#define dbg_io(fmt, ...) ({})
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_MSG_BLD
/* Initialization and build messages */
#define dbg_bld(fmt, ...) \
printk(KERN_DEBUG "UBI DBG bld: %s: " fmt "\n", __FUNCTION__, \
##__VA_ARGS__)
#else
#define dbg_bld(fmt, ...) ({})
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_EMULATE_BITFLIPS
/**
* ubi_dbg_is_bitflip - if it is time to emulate a bit-flip.
*
* Returns non-zero if a bit-flip should be emulated, otherwise returns zero.
*/
static inline int ubi_dbg_is_bitflip(void)
{
return !(random32() % 200);
}
#else
#define ubi_dbg_is_bitflip() 0
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_EMULATE_WRITE_FAILURES
/**
* ubi_dbg_is_write_failure - if it is time to emulate a write failure.
*
* Returns non-zero if a write failure should be emulated, otherwise returns
* zero.
*/
static inline int ubi_dbg_is_write_failure(void)
{
return !(random32() % 500);
}
#else
#define ubi_dbg_is_write_failure() 0
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_EMULATE_ERASE_FAILURES
/**
* ubi_dbg_is_erase_failure - if its time to emulate an erase failure.
*
* Returns non-zero if an erase failure should be emulated, otherwise returns
* zero.
*/
static inline int ubi_dbg_is_erase_failure(void)
{
return !(random32() % 400);
}
#else
#define ubi_dbg_is_erase_failure() 0
#endif
#endif /* !__UBI_DEBUG_H__ */

1241
drivers/mtd/ubi/eba.c Normal file

File diff suppressed because it is too large Load Diff

324
drivers/mtd/ubi/gluebi.c Normal file
View File

@ -0,0 +1,324 @@
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём), Joern Engel
*/
/*
* This file includes implementation of fake MTD devices for each UBI volume.
* This sounds strange, but it is in fact quite useful to make MTD-oriented
* software (including all the legacy software) to work on top of UBI.
*
* Gluebi emulates MTD devices of "MTD_UBIVOLUME" type. Their minimal I/O unit
* size (mtd->writesize) is equivalent to the UBI minimal I/O unit. The
* eraseblock size is equivalent to the logical eraseblock size of the volume.
*/
#include <asm/div64.h>
#include "ubi.h"
/**
* gluebi_get_device - get MTD device reference.
* @mtd: the MTD device description object
*
* This function is called every time the MTD device is being opened and
* implements the MTD get_device() operation. Returns zero in case of success
* and a negative error code in case of failure.
*/
static int gluebi_get_device(struct mtd_info *mtd)
{
struct ubi_volume *vol;
vol = container_of(mtd, struct ubi_volume, gluebi_mtd);
/*
* We do not introduce locks for gluebi reference count because the
* get_device()/put_device() calls are already serialized at MTD.
*/
if (vol->gluebi_refcount > 0) {
/*
* The MTD device is already referenced and this is just one
* more reference. MTD allows many users to open the same
* volume simultaneously and do not distinguish between
* readers/writers/exclusive openers as UBI does. So we do not
* open the UBI volume again - just increase the reference
* counter and return.
*/
vol->gluebi_refcount += 1;
return 0;
}
/*
* This is the first reference to this UBI volume via the MTD device
* interface. Open the corresponding volume in read-write mode.
*/
vol->gluebi_desc = ubi_open_volume(vol->ubi->ubi_num, vol->vol_id,
UBI_READWRITE);
if (IS_ERR(vol->gluebi_desc))
return PTR_ERR(vol->gluebi_desc);
vol->gluebi_refcount += 1;
return 0;
}
/**
* gluebi_put_device - put MTD device reference.
* @mtd: the MTD device description object
*
* This function is called every time the MTD device is being put. Returns
* zero in case of success and a negative error code in case of failure.
*/
static void gluebi_put_device(struct mtd_info *mtd)
{
struct ubi_volume *vol;
vol = container_of(mtd, struct ubi_volume, gluebi_mtd);
vol->gluebi_refcount -= 1;
ubi_assert(vol->gluebi_refcount >= 0);
if (vol->gluebi_refcount == 0)
ubi_close_volume(vol->gluebi_desc);
}
/**
* gluebi_read - read operation of emulated MTD devices.
* @mtd: MTD device description object
* @from: absolute offset from where to read
* @len: how many bytes to read
* @retlen: count of read bytes is returned here
* @buf: buffer to store the read data
*
* This function returns zero in case of success and a negative error code in
* case of failure.
*/
static int gluebi_read(struct mtd_info *mtd, loff_t from, size_t len,
size_t *retlen, unsigned char *buf)
{
int err = 0, lnum, offs, total_read;
struct ubi_volume *vol;
struct ubi_device *ubi;
uint64_t tmp = from;
dbg_msg("read %zd bytes from offset %lld", len, from);
if (len < 0 || from < 0 || from + len > mtd->size)
return -EINVAL;
vol = container_of(mtd, struct ubi_volume, gluebi_mtd);
ubi = vol->ubi;
offs = do_div(tmp, mtd->erasesize);
lnum = tmp;
total_read = len;
while (total_read) {
size_t to_read = mtd->erasesize - offs;
if (to_read > total_read)
to_read = total_read;
err = ubi_eba_read_leb(ubi, vol->vol_id, lnum, buf, offs,
to_read, 0);
if (err)
break;
lnum += 1;
offs = 0;
total_read -= to_read;
buf += to_read;
}
*retlen = len - total_read;
return err;
}
/**
* gluebi_write - write operation of emulated MTD devices.
* @mtd: MTD device description object
* @to: absolute offset where to write
* @len: how many bytes to write
* @retlen: count of written bytes is returned here
* @buf: buffer with data to write
*
* This function returns zero in case of success and a negative error code in
* case of failure.
*/
static int gluebi_write(struct mtd_info *mtd, loff_t to, size_t len,
size_t *retlen, const u_char *buf)
{
int err = 0, lnum, offs, total_written;
struct ubi_volume *vol;
struct ubi_device *ubi;
uint64_t tmp = to;
dbg_msg("write %zd bytes to offset %lld", len, to);
if (len < 0 || to < 0 || len + to > mtd->size)
return -EINVAL;
vol = container_of(mtd, struct ubi_volume, gluebi_mtd);
ubi = vol->ubi;
if (ubi->ro_mode)
return -EROFS;
offs = do_div(tmp, mtd->erasesize);
lnum = tmp;
if (len % mtd->writesize || offs % mtd->writesize)
return -EINVAL;
total_written = len;
while (total_written) {
size_t to_write = mtd->erasesize - offs;
if (to_write > total_written)
to_write = total_written;
err = ubi_eba_write_leb(ubi, vol->vol_id, lnum, buf, offs,
to_write, UBI_UNKNOWN);
if (err)
break;
lnum += 1;
offs = 0;
total_written -= to_write;
buf += to_write;
}
*retlen = len - total_written;
return err;
}
/**
* gluebi_erase - erase operation of emulated MTD devices.
* @mtd: the MTD device description object
* @instr: the erase operation description
*
* This function calls the erase callback when finishes. Returns zero in case
* of success and a negative error code in case of failure.
*/
static int gluebi_erase(struct mtd_info *mtd, struct erase_info *instr)
{
int err, i, lnum, count;
struct ubi_volume *vol;
struct ubi_device *ubi;
dbg_msg("erase %u bytes at offset %u", instr->len, instr->addr);
if (instr->addr < 0 || instr->addr > mtd->size - mtd->erasesize)
return -EINVAL;
if (instr->len < 0 || instr->addr + instr->len > mtd->size)
return -EINVAL;
if (instr->addr % mtd->writesize || instr->len % mtd->writesize)
return -EINVAL;
lnum = instr->addr / mtd->erasesize;
count = instr->len / mtd->erasesize;
vol = container_of(mtd, struct ubi_volume, gluebi_mtd);
ubi = vol->ubi;
if (ubi->ro_mode)
return -EROFS;
for (i = 0; i < count; i++) {
err = ubi_eba_unmap_leb(ubi, vol->vol_id, lnum + i);
if (err)
goto out_err;
}
/*
* MTD erase operations are synchronous, so we have to make sure the
* physical eraseblock is wiped out.
*/
err = ubi_wl_flush(ubi);
if (err)
goto out_err;
instr->state = MTD_ERASE_DONE;
mtd_erase_callback(instr);
return 0;
out_err:
instr->state = MTD_ERASE_FAILED;
instr->fail_addr = lnum * mtd->erasesize;
return err;
}
/**
* ubi_create_gluebi - initialize gluebi for an UBI volume.
* @ubi: UBI device description object
* @vol: volume description object
*
* This function is called when an UBI volume is created in order to create
* corresponding fake MTD device. Returns zero in case of success and a
* negative error code in case of failure.
*/
int ubi_create_gluebi(struct ubi_device *ubi, struct ubi_volume *vol)
{
int err;
struct mtd_info *mtd = &vol->gluebi_mtd;
mtd->name = kmemdup(vol->name, vol->name_len + 1, GFP_KERNEL);
if (!mtd->name)
return -ENOMEM;
mtd->type = MTD_UBIVOLUME;
if (!ubi->ro_mode)
mtd->flags = MTD_WRITEABLE;
mtd->writesize = ubi->min_io_size;
mtd->owner = THIS_MODULE;
mtd->size = vol->usable_leb_size * vol->reserved_pebs;
mtd->erasesize = vol->usable_leb_size;
mtd->read = gluebi_read;
mtd->write = gluebi_write;
mtd->erase = gluebi_erase;
mtd->get_device = gluebi_get_device;
mtd->put_device = gluebi_put_device;
if (add_mtd_device(mtd)) {
ubi_err("cannot not add MTD device\n");
kfree(mtd->name);
return -ENFILE;
}
dbg_msg("added mtd%d (\"%s\"), size %u, EB size %u",
mtd->index, mtd->name, mtd->size, mtd->erasesize);
return 0;
}
/**
* ubi_destroy_gluebi - close gluebi for an UBI volume.
* @vol: volume description object
*
* This function is called when an UBI volume is removed in order to remove
* corresponding fake MTD device. Returns zero in case of success and a
* negative error code in case of failure.
*/
int ubi_destroy_gluebi(struct ubi_volume *vol)
{
int err;
struct mtd_info *mtd = &vol->gluebi_mtd;
dbg_msg("remove mtd%d", mtd->index);
err = del_mtd_device(mtd);
if (err)
return err;
kfree(mtd->name);
return 0;
}

1259
drivers/mtd/ubi/io.c Normal file

File diff suppressed because it is too large Load Diff

575
drivers/mtd/ubi/kapi.c Normal file
View File

@ -0,0 +1,575 @@
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*/
/* This file mostly implements UBI kernel API functions */
#include <linux/module.h>
#include <linux/err.h>
#include <asm/div64.h>
#include "ubi.h"
/**
* ubi_get_device_info - get information about UBI device.
* @ubi_num: UBI device number
* @di: the information is stored here
*
* This function returns %0 in case of success and a %-ENODEV if there is no
* such UBI device.
*/
int ubi_get_device_info(int ubi_num, struct ubi_device_info *di)
{
const struct ubi_device *ubi;
if (!try_module_get(THIS_MODULE))
return -ENODEV;
if (ubi_num < 0 || ubi_num >= UBI_MAX_DEVICES ||
!ubi_devices[ubi_num]) {
module_put(THIS_MODULE);
return -ENODEV;
}
ubi = ubi_devices[ubi_num];
di->ubi_num = ubi->ubi_num;
di->leb_size = ubi->leb_size;
di->min_io_size = ubi->min_io_size;
di->ro_mode = ubi->ro_mode;
di->cdev = MKDEV(ubi->major, 0);
module_put(THIS_MODULE);
return 0;
}
EXPORT_SYMBOL_GPL(ubi_get_device_info);
/**
* ubi_get_volume_info - get information about UBI volume.
* @desc: volume descriptor
* @vi: the information is stored here
*/
void ubi_get_volume_info(struct ubi_volume_desc *desc,
struct ubi_volume_info *vi)
{
const struct ubi_volume *vol = desc->vol;
const struct ubi_device *ubi = vol->ubi;
vi->vol_id = vol->vol_id;
vi->ubi_num = ubi->ubi_num;
vi->size = vol->reserved_pebs;
vi->used_bytes = vol->used_bytes;
vi->vol_type = vol->vol_type;
vi->corrupted = vol->corrupted;
vi->upd_marker = vol->upd_marker;
vi->alignment = vol->alignment;
vi->usable_leb_size = vol->usable_leb_size;
vi->name_len = vol->name_len;
vi->name = vol->name;
vi->cdev = MKDEV(ubi->major, vi->vol_id + 1);
}
EXPORT_SYMBOL_GPL(ubi_get_volume_info);
/**
* ubi_open_volume - open UBI volume.
* @ubi_num: UBI device number
* @vol_id: volume ID
* @mode: open mode
*
* The @mode parameter specifies if the volume should be opened in read-only
* mode, read-write mode, or exclusive mode. The exclusive mode guarantees that
* nobody else will be able to open this volume. UBI allows to have many volume
* readers and one writer at a time.
*
* If a static volume is being opened for the first time since boot, it will be
* checked by this function, which means it will be fully read and the CRC
* checksum of each logical eraseblock will be checked.
*
* This function returns volume descriptor in case of success and a negative
* error code in case of failure.
*/
struct ubi_volume_desc *ubi_open_volume(int ubi_num, int vol_id, int mode)
{
int err;
struct ubi_volume_desc *desc;
struct ubi_device *ubi = ubi_devices[ubi_num];
struct ubi_volume *vol;
dbg_msg("open device %d volume %d, mode %d", ubi_num, vol_id, mode);
err = -ENODEV;
if (!try_module_get(THIS_MODULE))
return ERR_PTR(err);
if (ubi_num < 0 || ubi_num >= UBI_MAX_DEVICES || !ubi)
goto out_put;
err = -EINVAL;
if (vol_id < 0 || vol_id >= ubi->vtbl_slots)
goto out_put;
if (mode != UBI_READONLY && mode != UBI_READWRITE &&
mode != UBI_EXCLUSIVE)
goto out_put;
desc = kmalloc(sizeof(struct ubi_volume_desc), GFP_KERNEL);
if (!desc) {
err = -ENOMEM;
goto out_put;
}
spin_lock(&ubi->volumes_lock);
vol = ubi->volumes[vol_id];
if (!vol) {
err = -ENODEV;
goto out_unlock;
}
err = -EBUSY;
switch (mode) {
case UBI_READONLY:
if (vol->exclusive)
goto out_unlock;
vol->readers += 1;
break;
case UBI_READWRITE:
if (vol->exclusive || vol->writers > 0)
goto out_unlock;
vol->writers += 1;
break;
case UBI_EXCLUSIVE:
if (vol->exclusive || vol->writers || vol->readers)
goto out_unlock;
vol->exclusive = 1;
break;
}
spin_unlock(&ubi->volumes_lock);
desc->vol = vol;
desc->mode = mode;
/*
* To prevent simultaneous checks of the same volume we use @vtbl_mutex,
* although it is not the purpose it was introduced for.
*/
mutex_lock(&ubi->vtbl_mutex);
if (!vol->checked) {
/* This is the first open - check the volume */
err = ubi_check_volume(ubi, vol_id);
if (err < 0) {
mutex_unlock(&ubi->vtbl_mutex);
ubi_close_volume(desc);
return ERR_PTR(err);
}
if (err == 1) {
ubi_warn("volume %d on UBI device %d is corrupted",
vol_id, ubi->ubi_num);
vol->corrupted = 1;
}
vol->checked = 1;
}
mutex_unlock(&ubi->vtbl_mutex);
return desc;
out_unlock:
spin_unlock(&ubi->volumes_lock);
kfree(desc);
out_put:
module_put(THIS_MODULE);
return ERR_PTR(err);
}
EXPORT_SYMBOL_GPL(ubi_open_volume);
/**
* ubi_open_volume_nm - open UBI volume by name.
* @ubi_num: UBI device number
* @name: volume name
* @mode: open mode
*
* This function is similar to 'ubi_open_volume()', but opens a volume by name.
*/
struct ubi_volume_desc *ubi_open_volume_nm(int ubi_num, const char *name,
int mode)
{
int i, vol_id = -1, len;
struct ubi_volume_desc *ret;
struct ubi_device *ubi;
dbg_msg("open volume %s, mode %d", name, mode);
if (!name)
return ERR_PTR(-EINVAL);
len = strnlen(name, UBI_VOL_NAME_MAX + 1);
if (len > UBI_VOL_NAME_MAX)
return ERR_PTR(-EINVAL);
ret = ERR_PTR(-ENODEV);
if (!try_module_get(THIS_MODULE))
return ret;
if (ubi_num < 0 || ubi_num >= UBI_MAX_DEVICES || !ubi_devices[ubi_num])
goto out_put;
ubi = ubi_devices[ubi_num];
spin_lock(&ubi->volumes_lock);
/* Walk all volumes of this UBI device */
for (i = 0; i < ubi->vtbl_slots; i++) {
struct ubi_volume *vol = ubi->volumes[i];
if (vol && len == vol->name_len && !strcmp(name, vol->name)) {
vol_id = i;
break;
}
}
spin_unlock(&ubi->volumes_lock);
if (vol_id < 0)
goto out_put;
ret = ubi_open_volume(ubi_num, vol_id, mode);
out_put:
module_put(THIS_MODULE);
return ret;
}
EXPORT_SYMBOL_GPL(ubi_open_volume_nm);
/**
* ubi_close_volume - close UBI volume.
* @desc: volume descriptor
*/
void ubi_close_volume(struct ubi_volume_desc *desc)
{
struct ubi_volume *vol = desc->vol;
dbg_msg("close volume %d, mode %d", vol->vol_id, desc->mode);
spin_lock(&vol->ubi->volumes_lock);
switch (desc->mode) {
case UBI_READONLY:
vol->readers -= 1;
break;
case UBI_READWRITE:
vol->writers -= 1;
break;
case UBI_EXCLUSIVE:
vol->exclusive = 0;
}
spin_unlock(&vol->ubi->volumes_lock);
kfree(desc);
module_put(THIS_MODULE);
}
EXPORT_SYMBOL_GPL(ubi_close_volume);
/**
* ubi_leb_read - read data.
* @desc: volume descriptor
* @lnum: logical eraseblock number to read from
* @buf: buffer where to store the read data
* @offset: offset within the logical eraseblock to read from
* @len: how many bytes to read
* @check: whether UBI has to check the read data's CRC or not.
*
* This function reads data from offset @offset of logical eraseblock @lnum and
* stores the data at @buf. When reading from static volumes, @check specifies
* whether the data has to be checked or not. If yes, the whole logical
* eraseblock will be read and its CRC checksum will be checked (i.e., the CRC
* checksum is per-eraseblock). So checking may substantially slow down the
* read speed. The @check argument is ignored for dynamic volumes.
*
* In case of success, this function returns zero. In case of failure, this
* function returns a negative error code.
*
* %-EBADMSG error code is returned:
* o for both static and dynamic volumes if MTD driver has detected a data
* integrity problem (unrecoverable ECC checksum mismatch in case of NAND);
* o for static volumes in case of data CRC mismatch.
*
* If the volume is damaged because of an interrupted update this function just
* returns immediately with %-EBADF error code.
*/
int ubi_leb_read(struct ubi_volume_desc *desc, int lnum, char *buf, int offset,
int len, int check)
{
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
int err, vol_id = vol->vol_id;
dbg_msg("read %d bytes from LEB %d:%d:%d", len, vol_id, lnum, offset);
if (vol_id < 0 || vol_id >= ubi->vtbl_slots || lnum < 0 ||
lnum >= vol->used_ebs || offset < 0 || len < 0 ||
offset + len > vol->usable_leb_size)
return -EINVAL;
if (vol->vol_type == UBI_STATIC_VOLUME && lnum == vol->used_ebs - 1 &&
offset + len > vol->last_eb_bytes)
return -EINVAL;
if (vol->upd_marker)
return -EBADF;
if (len == 0)
return 0;
err = ubi_eba_read_leb(ubi, vol_id, lnum, buf, offset, len, check);
if (err && err == -EBADMSG && vol->vol_type == UBI_STATIC_VOLUME) {
ubi_warn("mark volume %d as corrupted", vol_id);
vol->corrupted = 1;
}
return err;
}
EXPORT_SYMBOL_GPL(ubi_leb_read);
/**
* ubi_leb_write - write data.
* @desc: volume descriptor
* @lnum: logical eraseblock number to write to
* @buf: data to write
* @offset: offset within the logical eraseblock where to write
* @len: how many bytes to write
* @dtype: expected data type
*
* This function writes @len bytes of data from @buf to offset @offset of
* logical eraseblock @lnum. The @dtype argument describes expected lifetime of
* the data.
*
* This function takes care of physical eraseblock write failures. If write to
* the physical eraseblock write operation fails, the logical eraseblock is
* re-mapped to another physical eraseblock, the data is recovered, and the
* write finishes. UBI has a pool of reserved physical eraseblocks for this.
*
* If all the data were successfully written, zero is returned. If an error
* occurred and UBI has not been able to recover from it, this function returns
* a negative error code. Note, in case of an error, it is possible that
* something was still written to the flash media, but that may be some
* garbage.
*
* If the volume is damaged because of an interrupted update this function just
* returns immediately with %-EBADF code.
*/
int ubi_leb_write(struct ubi_volume_desc *desc, int lnum, const void *buf,
int offset, int len, int dtype)
{
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
int vol_id = vol->vol_id;
dbg_msg("write %d bytes to LEB %d:%d:%d", len, vol_id, lnum, offset);
if (vol_id < 0 || vol_id >= ubi->vtbl_slots)
return -EINVAL;
if (desc->mode == UBI_READONLY || vol->vol_type == UBI_STATIC_VOLUME)
return -EROFS;
if (lnum < 0 || lnum >= vol->reserved_pebs || offset < 0 || len < 0 ||
offset + len > vol->usable_leb_size || offset % ubi->min_io_size ||
len % ubi->min_io_size)
return -EINVAL;
if (dtype != UBI_LONGTERM && dtype != UBI_SHORTTERM &&
dtype != UBI_UNKNOWN)
return -EINVAL;
if (vol->upd_marker)
return -EBADF;
if (len == 0)
return 0;
return ubi_eba_write_leb(ubi, vol_id, lnum, buf, offset, len, dtype);
}
EXPORT_SYMBOL_GPL(ubi_leb_write);
/*
* ubi_leb_change - change logical eraseblock atomically.
* @desc: volume descriptor
* @lnum: logical eraseblock number to change
* @buf: data to write
* @len: how many bytes to write
* @dtype: expected data type
*
* This function changes the contents of a logical eraseblock atomically. @buf
* has to contain new logical eraseblock data, and @len - the length of the
* data, which has to be aligned. The length may be shorter then the logical
* eraseblock size, ant the logical eraseblock may be appended to more times
* later on. This function guarantees that in case of an unclean reboot the old
* contents is preserved. Returns zero in case of success and a negative error
* code in case of failure.
*/
int ubi_leb_change(struct ubi_volume_desc *desc, int lnum, const void *buf,
int len, int dtype)
{
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
int vol_id = vol->vol_id;
dbg_msg("atomically write %d bytes to LEB %d:%d", len, vol_id, lnum);
if (vol_id < 0 || vol_id >= ubi->vtbl_slots)
return -EINVAL;
if (desc->mode == UBI_READONLY || vol->vol_type == UBI_STATIC_VOLUME)
return -EROFS;
if (lnum < 0 || lnum >= vol->reserved_pebs || len < 0 ||
len > vol->usable_leb_size || len % ubi->min_io_size)
return -EINVAL;
if (dtype != UBI_LONGTERM && dtype != UBI_SHORTTERM &&
dtype != UBI_UNKNOWN)
return -EINVAL;
if (vol->upd_marker)
return -EBADF;
if (len == 0)
return 0;
return ubi_eba_atomic_leb_change(ubi, vol_id, lnum, buf, len, dtype);
}
EXPORT_SYMBOL_GPL(ubi_leb_change);
/**
* ubi_leb_erase - erase logical eraseblock.
* @desc: volume descriptor
* @lnum: logical eraseblock number
*
* This function un-maps logical eraseblock @lnum and synchronously erases the
* correspondent physical eraseblock. Returns zero in case of success and a
* negative error code in case of failure.
*
* If the volume is damaged because of an interrupted update this function just
* returns immediately with %-EBADF code.
*/
int ubi_leb_erase(struct ubi_volume_desc *desc, int lnum)
{
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
int err, vol_id = vol->vol_id;
dbg_msg("erase LEB %d:%d", vol_id, lnum);
if (desc->mode == UBI_READONLY || vol->vol_type == UBI_STATIC_VOLUME)
return -EROFS;
if (lnum < 0 || lnum >= vol->reserved_pebs)
return -EINVAL;
if (vol->upd_marker)
return -EBADF;
err = ubi_eba_unmap_leb(ubi, vol_id, lnum);
if (err)
return err;
return ubi_wl_flush(ubi);
}
EXPORT_SYMBOL_GPL(ubi_leb_erase);
/**
* ubi_leb_unmap - un-map logical eraseblock.
* @desc: volume descriptor
* @lnum: logical eraseblock number
*
* This function un-maps logical eraseblock @lnum and schedules the
* corresponding physical eraseblock for erasure, so that it will eventually be
* physically erased in background. This operation is much faster then the
* erase operation.
*
* Unlike erase, the un-map operation does not guarantee that the logical
* eraseblock will contain all 0xFF bytes when UBI is initialized again. For
* example, if several logical eraseblocks are un-mapped, and an unclean reboot
* happens after this, the logical eraseblocks will not necessarily be
* un-mapped again when this MTD device is attached. They may actually be
* mapped to the same physical eraseblocks again. So, this function has to be
* used with care.
*
* In other words, when un-mapping a logical eraseblock, UBI does not store
* any information about this on the flash media, it just marks the logical
* eraseblock as "un-mapped" in RAM. If UBI is detached before the physical
* eraseblock is physically erased, it will be mapped again to the same logical
* eraseblock when the MTD device is attached again.
*
* The main and obvious use-case of this function is when the contents of a
* logical eraseblock has to be re-written. Then it is much more efficient to
* first un-map it, then write new data, rather then first erase it, then write
* new data. Note, once new data has been written to the logical eraseblock,
* UBI guarantees that the old contents has gone forever. In other words, if an
* unclean reboot happens after the logical eraseblock has been un-mapped and
* then written to, it will contain the last written data.
*
* This function returns zero in case of success and a negative error code in
* case of failure. If the volume is damaged because of an interrupted update
* this function just returns immediately with %-EBADF code.
*/
int ubi_leb_unmap(struct ubi_volume_desc *desc, int lnum)
{
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
int vol_id = vol->vol_id;
dbg_msg("unmap LEB %d:%d", vol_id, lnum);
if (desc->mode == UBI_READONLY || vol->vol_type == UBI_STATIC_VOLUME)
return -EROFS;
if (lnum < 0 || lnum >= vol->reserved_pebs)
return -EINVAL;
if (vol->upd_marker)
return -EBADF;
return ubi_eba_unmap_leb(ubi, vol_id, lnum);
}
EXPORT_SYMBOL_GPL(ubi_leb_unmap);
/**
* ubi_is_mapped - check if logical eraseblock is mapped.
* @desc: volume descriptor
* @lnum: logical eraseblock number
*
* This function checks if logical eraseblock @lnum is mapped to a physical
* eraseblock. If a logical eraseblock is un-mapped, this does not necessarily
* mean it will still be un-mapped after the UBI device is re-attached. The
* logical eraseblock may become mapped to the physical eraseblock it was last
* mapped to.
*
* This function returns %1 if the LEB is mapped, %0 if not, and a negative
* error code in case of failure. If the volume is damaged because of an
* interrupted update this function just returns immediately with %-EBADF error
* code.
*/
int ubi_is_mapped(struct ubi_volume_desc *desc, int lnum)
{
struct ubi_volume *vol = desc->vol;
dbg_msg("test LEB %d:%d", vol->vol_id, lnum);
if (lnum < 0 || lnum >= vol->reserved_pebs)
return -EINVAL;
if (vol->upd_marker)
return -EBADF;
return vol->eba_tbl[lnum] >= 0;
}
EXPORT_SYMBOL_GPL(ubi_is_mapped);

105
drivers/mtd/ubi/misc.c Normal file
View File

@ -0,0 +1,105 @@
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*/
/* Here we keep miscellaneous functions which are used all over the UBI code */
#include "ubi.h"
/**
* calc_data_len - calculate how much real data is stored in a buffer.
* @ubi: UBI device description object
* @buf: a buffer with the contents of the physical eraseblock
* @length: the buffer length
*
* This function calculates how much "real data" is stored in @buf and returnes
* the length. Continuous 0xFF bytes at the end of the buffer are not
* considered as "real data".
*/
int ubi_calc_data_len(const struct ubi_device *ubi, const void *buf,
int length)
{
int i;
ubi_assert(length % ubi->min_io_size == 0);
for (i = length - 1; i >= 0; i--)
if (((const uint8_t *)buf)[i] != 0xFF)
break;
/* The resulting length must be aligned to the minimum flash I/O size */
length = ALIGN(i + 1, ubi->min_io_size);
return length;
}
/**
* ubi_check_volume - check the contents of a static volume.
* @ubi: UBI device description object
* @vol_id: ID of the volume to check
*
* This function checks if static volume @vol_id is corrupted by fully reading
* it and checking data CRC. This function returns %0 if the volume is not
* corrupted, %1 if it is corrupted and a negative error code in case of
* failure. Dynamic volumes are not checked and zero is returned immediately.
*/
int ubi_check_volume(struct ubi_device *ubi, int vol_id)
{
void *buf;
int err = 0, i;
struct ubi_volume *vol = ubi->volumes[vol_id];
if (vol->vol_type != UBI_STATIC_VOLUME)
return 0;
buf = kmalloc(vol->usable_leb_size, GFP_KERNEL);
if (!buf)
return -ENOMEM;
for (i = 0; i < vol->used_ebs; i++) {
int size;
if (i == vol->used_ebs - 1)
size = vol->last_eb_bytes;
else
size = vol->usable_leb_size;
err = ubi_eba_read_leb(ubi, vol_id, i, buf, 0, size, 1);
if (err) {
if (err == -EBADMSG)
err = 1;
break;
}
}
kfree(buf);
return err;
}
/**
* ubi_calculate_rsvd_pool - calculate how many PEBs must be reserved for bad
* eraseblock handling.
* @ubi: UBI device description object
*/
void ubi_calculate_reserved(struct ubi_device *ubi)
{
ubi->beb_rsvd_level = ubi->good_peb_count/100;
ubi->beb_rsvd_level *= CONFIG_MTD_UBI_BEB_RESERVE;
if (ubi->beb_rsvd_level < MIN_RESEVED_PEBS)
ubi->beb_rsvd_level = MIN_RESEVED_PEBS;
}

1368
drivers/mtd/ubi/scan.c Normal file

File diff suppressed because it is too large Load Diff

167
drivers/mtd/ubi/scan.h Normal file
View File

@ -0,0 +1,167 @@
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*/
#ifndef __UBI_SCAN_H__
#define __UBI_SCAN_H__
/* The erase counter value for this physical eraseblock is unknown */
#define UBI_SCAN_UNKNOWN_EC (-1)
/**
* struct ubi_scan_leb - scanning information about a physical eraseblock.
* @ec: erase counter (%UBI_SCAN_UNKNOWN_EC if it is unknown)
* @pnum: physical eraseblock number
* @lnum: logical eraseblock number
* @scrub: if this physical eraseblock needs scrubbing
* @sqnum: sequence number
* @u: unions RB-tree or @list links
* @u.rb: link in the per-volume RB-tree of &struct ubi_scan_leb objects
* @u.list: link in one of the eraseblock lists
* @leb_ver: logical eraseblock version (obsolete)
*
* One object of this type is allocated for each physical eraseblock during
* scanning.
*/
struct ubi_scan_leb {
int ec;
int pnum;
int lnum;
int scrub;
unsigned long long sqnum;
union {
struct rb_node rb;
struct list_head list;
} u;
uint32_t leb_ver;
};
/**
* struct ubi_scan_volume - scanning information about a volume.
* @vol_id: volume ID
* @highest_lnum: highest logical eraseblock number in this volume
* @leb_count: number of logical eraseblocks in this volume
* @vol_type: volume type
* @used_ebs: number of used logical eraseblocks in this volume (only for
* static volumes)
* @last_data_size: amount of data in the last logical eraseblock of this
* volume (always equivalent to the usable logical eraseblock size in case of
* dynamic volumes)
* @data_pad: how many bytes at the end of logical eraseblocks of this volume
* are not used (due to volume alignment)
* @compat: compatibility flags of this volume
* @rb: link in the volume RB-tree
* @root: root of the RB-tree containing all the eraseblock belonging to this
* volume (&struct ubi_scan_leb objects)
*
* One object of this type is allocated for each volume during scanning.
*/
struct ubi_scan_volume {
int vol_id;
int highest_lnum;
int leb_count;
int vol_type;
int used_ebs;
int last_data_size;
int data_pad;
int compat;
struct rb_node rb;
struct rb_root root;
};
/**
* struct ubi_scan_info - UBI scanning information.
* @volumes: root of the volume RB-tree
* @corr: list of corrupted physical eraseblocks
* @free: list of free physical eraseblocks
* @erase: list of physical eraseblocks which have to be erased
* @alien: list of physical eraseblocks which should not be used by UBI (e.g.,
* @bad_peb_count: count of bad physical eraseblocks
* those belonging to "preserve"-compatible internal volumes)
* @vols_found: number of volumes found during scanning
* @highest_vol_id: highest volume ID
* @alien_peb_count: count of physical eraseblocks in the @alien list
* @is_empty: flag indicating whether the MTD device is empty or not
* @min_ec: lowest erase counter value
* @max_ec: highest erase counter value
* @max_sqnum: highest sequence number value
* @mean_ec: mean erase counter value
* @ec_sum: a temporary variable used when calculating @mean_ec
* @ec_count: a temporary variable used when calculating @mean_ec
*
* This data structure contains the result of scanning and may be used by other
* UBI units to build final UBI data structures, further error-recovery and so
* on.
*/
struct ubi_scan_info {
struct rb_root volumes;
struct list_head corr;
struct list_head free;
struct list_head erase;
struct list_head alien;
int bad_peb_count;
int vols_found;
int highest_vol_id;
int alien_peb_count;
int is_empty;
int min_ec;
int max_ec;
unsigned long long max_sqnum;
int mean_ec;
int ec_sum;
int ec_count;
};
struct ubi_device;
struct ubi_vid_hdr;
/*
* ubi_scan_move_to_list - move a physical eraseblock from the volume tree to a
* list.
*
* @sv: volume scanning information
* @seb: scanning eraseblock infprmation
* @list: the list to move to
*/
static inline void ubi_scan_move_to_list(struct ubi_scan_volume *sv,
struct ubi_scan_leb *seb,
struct list_head *list)
{
rb_erase(&seb->u.rb, &sv->root);
list_add_tail(&seb->u.list, list);
}
int ubi_scan_add_to_list(struct ubi_scan_info *si, int pnum, int ec,
struct list_head *list);
int ubi_scan_add_used(const struct ubi_device *ubi, struct ubi_scan_info *si,
int pnum, int ec, const struct ubi_vid_hdr *vid_hdr,
int bitflips);
struct ubi_scan_volume *ubi_scan_find_sv(const struct ubi_scan_info *si,
int vol_id);
struct ubi_scan_leb *ubi_scan_find_seb(const struct ubi_scan_volume *sv,
int lnum);
void ubi_scan_rm_volume(struct ubi_scan_info *si, struct ubi_scan_volume *sv);
struct ubi_scan_leb *ubi_scan_get_free_peb(const struct ubi_device *ubi,
struct ubi_scan_info *si);
int ubi_scan_erase_peb(const struct ubi_device *ubi,
const struct ubi_scan_info *si, int pnum, int ec);
struct ubi_scan_info *ubi_scan(struct ubi_device *ubi);
void ubi_scan_destroy_si(struct ubi_scan_info *si);
#endif /* !__UBI_SCAN_H__ */

535
drivers/mtd/ubi/ubi.h Normal file
View File

@ -0,0 +1,535 @@
/*
* Copyright (c) International Business Machines Corp., 2006
* Copyright (c) Nokia Corporation, 2006, 2007
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*/
#ifndef __UBI_UBI_H__
#define __UBI_UBI_H__
#include <linux/init.h>
#include <linux/types.h>
#include <linux/list.h>
#include <linux/rbtree.h>
#include <linux/sched.h>
#include <linux/wait.h>
#include <linux/mutex.h>
#include <linux/rwsem.h>
#include <linux/spinlock.h>
#include <linux/fs.h>
#include <linux/cdev.h>
#include <linux/device.h>
#include <linux/string.h>
#include <linux/mtd/mtd.h>
#include <mtd/ubi-header.h>
#include <linux/mtd/ubi.h>
#include "scan.h"
#include "debug.h"
/* Maximum number of supported UBI devices */
#define UBI_MAX_DEVICES 32
/* UBI name used for character devices, sysfs, etc */
#define UBI_NAME_STR "ubi"
/* Normal UBI messages */
#define ubi_msg(fmt, ...) printk(KERN_NOTICE "UBI: " fmt "\n", ##__VA_ARGS__)
/* UBI warning messages */
#define ubi_warn(fmt, ...) printk(KERN_WARNING "UBI warning: %s: " fmt "\n", \
__FUNCTION__, ##__VA_ARGS__)
/* UBI error messages */
#define ubi_err(fmt, ...) printk(KERN_ERR "UBI error: %s: " fmt "\n", \
__FUNCTION__, ##__VA_ARGS__)
/* Lowest number PEBs reserved for bad PEB handling */
#define MIN_RESEVED_PEBS 2
/* Background thread name pattern */
#define UBI_BGT_NAME_PATTERN "ubi_bgt%dd"
/* This marker in the EBA table means that the LEB is um-mapped */
#define UBI_LEB_UNMAPPED -1
/*
* In case of errors, UBI tries to repeat the operation several times before
* returning error. The below constant defines how many times UBI re-tries.
*/
#define UBI_IO_RETRIES 3
/*
* Error codes returned by the I/O unit.
*
* UBI_IO_PEB_EMPTY: the physical eraseblock is empty, i.e. it contains only
* 0xFF bytes
* UBI_IO_PEB_FREE: the physical eraseblock is free, i.e. it contains only a
* valid erase counter header, and the rest are %0xFF bytes
* UBI_IO_BAD_EC_HDR: the erase counter header is corrupted (bad magic or CRC)
* UBI_IO_BAD_VID_HDR: the volume identifier header is corrupted (bad magic or
* CRC)
* UBI_IO_BITFLIPS: bit-flips were detected and corrected
*/
enum {
UBI_IO_PEB_EMPTY = 1,
UBI_IO_PEB_FREE,
UBI_IO_BAD_EC_HDR,
UBI_IO_BAD_VID_HDR,
UBI_IO_BITFLIPS
};
extern int ubi_devices_cnt;
extern struct ubi_device *ubi_devices[];
struct ubi_volume_desc;
/**
* struct ubi_volume - UBI volume description data structure.
* @dev: device object to make use of the the Linux device model
* @cdev: character device object to create character device
* @ubi: reference to the UBI device description object
* @vol_id: volume ID
* @readers: number of users holding this volume in read-only mode
* @writers: number of users holding this volume in read-write mode
* @exclusive: whether somebody holds this volume in exclusive mode
* @removed: if the volume was removed
* @checked: if this static volume was checked
*
* @reserved_pebs: how many physical eraseblocks are reserved for this volume
* @vol_type: volume type (%UBI_DYNAMIC_VOLUME or %UBI_STATIC_VOLUME)
* @usable_leb_size: logical eraseblock size without padding
* @used_ebs: how many logical eraseblocks in this volume contain data
* @last_eb_bytes: how many bytes are stored in the last logical eraseblock
* @used_bytes: how many bytes of data this volume contains
* @upd_marker: non-zero if the update marker is set for this volume
* @corrupted: non-zero if the volume is corrupted (static volumes only)
* @alignment: volume alignment
* @data_pad: how many bytes are not used at the end of physical eraseblocks to
* satisfy the requested alignment
* @name_len: volume name length
* @name: volume name
*
* @updating: whether the volume is being updated
* @upd_ebs: how many eraseblocks are expected to be updated
* @upd_bytes: how many bytes are expected to be received
* @upd_received: how many update bytes were already received
* @upd_buf: update buffer which is used to collect update data
*
* @eba_tbl: EBA table of this volume (LEB->PEB mapping)
*
* @gluebi_desc: gluebi UBI volume descriptor
* @gluebi_refcount: reference count of the gluebi MTD device
* @gluebi_mtd: MTD device description object of the gluebi MTD device
*
* The @corrupted field indicates that the volume's contents is corrupted.
* Since UBI protects only static volumes, this field is not relevant to
* dynamic volumes - it is user's responsibility to assure their data
* integrity.
*
* The @upd_marker flag indicates that this volume is either being updated at
* the moment or is damaged because of an unclean reboot.
*/
struct ubi_volume {
struct device dev;
struct cdev cdev;
struct ubi_device *ubi;
int vol_id;
int readers;
int writers;
int exclusive;
int removed;
int checked;
int reserved_pebs;
int vol_type;
int usable_leb_size;
int used_ebs;
int last_eb_bytes;
long long used_bytes;
int upd_marker;
int corrupted;
int alignment;
int data_pad;
int name_len;
char name[UBI_VOL_NAME_MAX+1];
int updating;
int upd_ebs;
long long upd_bytes;
long long upd_received;
void *upd_buf;
int *eba_tbl;
#ifdef CONFIG_MTD_UBI_GLUEBI
/* Gluebi-related stuff may be compiled out */
struct ubi_volume_desc *gluebi_desc;
int gluebi_refcount;
struct mtd_info gluebi_mtd;
#endif
};
/**
* struct ubi_volume_desc - descriptor of the UBI volume returned when it is
* opened.
* @vol: reference to the corresponding volume description object
* @mode: open mode (%UBI_READONLY, %UBI_READWRITE, or %UBI_EXCLUSIVE)
*/
struct ubi_volume_desc {
struct ubi_volume *vol;
int mode;
};
struct ubi_wl_entry;
/**
* struct ubi_device - UBI device description structure
* @dev: class device object to use the the Linux device model
* @cdev: character device object to create character device
* @ubi_num: UBI device number
* @ubi_name: UBI device name
* @major: character device major number
* @vol_count: number of volumes in this UBI device
* @volumes: volumes of this UBI device
* @volumes_lock: protects @volumes, @rsvd_pebs, @avail_pebs, beb_rsvd_pebs,
* @beb_rsvd_level, @bad_peb_count, @good_peb_count, @vol_count, @vol->readers,
* @vol->writers, @vol->exclusive, @vol->removed, @vol->mapping and
* @vol->eba_tbl.
*
* @rsvd_pebs: count of reserved physical eraseblocks
* @avail_pebs: count of available physical eraseblocks
* @beb_rsvd_pebs: how many physical eraseblocks are reserved for bad PEB
* handling
* @beb_rsvd_level: normal level of PEBs reserved for bad PEB handling
*
* @vtbl_slots: how many slots are available in the volume table
* @vtbl_size: size of the volume table in bytes
* @vtbl: in-RAM volume table copy
*
* @max_ec: current highest erase counter value
* @mean_ec: current mean erase counter value
*
* global_sqnum: global sequence number
* @ltree_lock: protects the lock tree and @global_sqnum
* @ltree: the lock tree
* @vtbl_mutex: protects on-flash volume table
*
* @used: RB-tree of used physical eraseblocks
* @free: RB-tree of free physical eraseblocks
* @scrub: RB-tree of physical eraseblocks which need scrubbing
* @prot: protection trees
* @prot.pnum: protection tree indexed by physical eraseblock numbers
* @prot.aec: protection tree indexed by absolute erase counter value
* @wl_lock: protects the @used, @free, @prot, @lookuptbl, @abs_ec, @move_from,
* @move_to, @move_to_put @erase_pending, @wl_scheduled, and @works
* fields
* @wl_scheduled: non-zero if the wear-leveling was scheduled
* @lookuptbl: a table to quickly find a &struct ubi_wl_entry object for any
* physical eraseblock
* @abs_ec: absolute erase counter
* @move_from: physical eraseblock from where the data is being moved
* @move_to: physical eraseblock where the data is being moved to
* @move_from_put: if the "from" PEB was put
* @move_to_put: if the "to" PEB was put
* @works: list of pending works
* @works_count: count of pending works
* @bgt_thread: background thread description object
* @thread_enabled: if the background thread is enabled
* @bgt_name: background thread name
*
* @flash_size: underlying MTD device size (in bytes)
* @peb_count: count of physical eraseblocks on the MTD device
* @peb_size: physical eraseblock size
* @bad_peb_count: count of bad physical eraseblocks
* @good_peb_count: count of good physical eraseblocks
* @min_io_size: minimal input/output unit size of the underlying MTD device
* @hdrs_min_io_size: minimal I/O unit size used for VID and EC headers
* @ro_mode: if the UBI device is in read-only mode
* @leb_size: logical eraseblock size
* @leb_start: starting offset of logical eraseblocks within physical
* eraseblocks
* @ec_hdr_alsize: size of the EC header aligned to @hdrs_min_io_size
* @vid_hdr_alsize: size of the VID header aligned to @hdrs_min_io_size
* @vid_hdr_offset: starting offset of the volume identifier header (might be
* unaligned)
* @vid_hdr_aloffset: starting offset of the VID header aligned to
* @hdrs_min_io_size
* @vid_hdr_shift: contains @vid_hdr_offset - @vid_hdr_aloffset
* @bad_allowed: whether the MTD device admits of bad physical eraseblocks or
* not
* @mtd: MTD device descriptor
*/
struct ubi_device {
struct cdev cdev;
struct device dev;
int ubi_num;
char ubi_name[sizeof(UBI_NAME_STR)+5];
int major;
int vol_count;
struct ubi_volume *volumes[UBI_MAX_VOLUMES+UBI_INT_VOL_COUNT];
spinlock_t volumes_lock;
int rsvd_pebs;
int avail_pebs;
int beb_rsvd_pebs;
int beb_rsvd_level;
int vtbl_slots;
int vtbl_size;
struct ubi_vtbl_record *vtbl;
struct mutex vtbl_mutex;
int max_ec;
int mean_ec;
/* EBA unit's stuff */
unsigned long long global_sqnum;
spinlock_t ltree_lock;
struct rb_root ltree;
/* Wear-leveling unit's stuff */
struct rb_root used;
struct rb_root free;
struct rb_root scrub;
struct {
struct rb_root pnum;
struct rb_root aec;
} prot;
spinlock_t wl_lock;
int wl_scheduled;
struct ubi_wl_entry **lookuptbl;
unsigned long long abs_ec;
struct ubi_wl_entry *move_from;
struct ubi_wl_entry *move_to;
int move_from_put;
int move_to_put;
struct list_head works;
int works_count;
struct task_struct *bgt_thread;
int thread_enabled;
char bgt_name[sizeof(UBI_BGT_NAME_PATTERN)+2];
/* I/O unit's stuff */
long long flash_size;
int peb_count;
int peb_size;
int bad_peb_count;
int good_peb_count;
int min_io_size;
int hdrs_min_io_size;
int ro_mode;
int leb_size;
int leb_start;
int ec_hdr_alsize;
int vid_hdr_alsize;
int vid_hdr_offset;
int vid_hdr_aloffset;
int vid_hdr_shift;
int bad_allowed;
struct mtd_info *mtd;
};
extern struct file_operations ubi_cdev_operations;
extern struct file_operations ubi_vol_cdev_operations;
extern struct class *ubi_class;
/* vtbl.c */
int ubi_change_vtbl_record(struct ubi_device *ubi, int idx,
struct ubi_vtbl_record *vtbl_rec);
int ubi_read_volume_table(struct ubi_device *ubi, struct ubi_scan_info *si);
/* vmt.c */
int ubi_create_volume(struct ubi_device *ubi, struct ubi_mkvol_req *req);
int ubi_remove_volume(struct ubi_volume_desc *desc);
int ubi_resize_volume(struct ubi_volume_desc *desc, int reserved_pebs);
int ubi_add_volume(struct ubi_device *ubi, int vol_id);
void ubi_free_volume(struct ubi_device *ubi, int vol_id);
/* upd.c */
int ubi_start_update(struct ubi_device *ubi, int vol_id, long long bytes);
int ubi_more_update_data(struct ubi_device *ubi, int vol_id,
const void __user *buf, int count);
/* misc.c */
int ubi_calc_data_len(const struct ubi_device *ubi, const void *buf, int length);
int ubi_check_volume(struct ubi_device *ubi, int vol_id);
void ubi_calculate_reserved(struct ubi_device *ubi);
/* gluebi.c */
#ifdef CONFIG_MTD_UBI_GLUEBI
int ubi_create_gluebi(struct ubi_device *ubi, struct ubi_volume *vol);
int ubi_destroy_gluebi(struct ubi_volume *vol);
#else
#define ubi_create_gluebi(ubi, vol) 0
#define ubi_destroy_gluebi(vol) 0
#endif
/* eba.c */
int ubi_eba_unmap_leb(struct ubi_device *ubi, int vol_id, int lnum);
int ubi_eba_read_leb(struct ubi_device *ubi, int vol_id, int lnum, void *buf,
int offset, int len, int check);
int ubi_eba_write_leb(struct ubi_device *ubi, int vol_id, int lnum,
const void *buf, int offset, int len, int dtype);
int ubi_eba_write_leb_st(struct ubi_device *ubi, int vol_id, int lnum,
const void *buf, int len, int dtype,
int used_ebs);
int ubi_eba_atomic_leb_change(struct ubi_device *ubi, int vol_id, int lnum,
const void *buf, int len, int dtype);
int ubi_eba_copy_leb(struct ubi_device *ubi, int from, int to,
struct ubi_vid_hdr *vid_hdr);
int ubi_eba_init_scan(struct ubi_device *ubi, struct ubi_scan_info *si);
void ubi_eba_close(const struct ubi_device *ubi);
/* wl.c */
int ubi_wl_get_peb(struct ubi_device *ubi, int dtype);
int ubi_wl_put_peb(struct ubi_device *ubi, int pnum, int torture);
int ubi_wl_flush(struct ubi_device *ubi);
int ubi_wl_scrub_peb(struct ubi_device *ubi, int pnum);
int ubi_wl_init_scan(struct ubi_device *ubi, struct ubi_scan_info *si);
void ubi_wl_close(struct ubi_device *ubi);
/* io.c */
int ubi_io_read(const struct ubi_device *ubi, void *buf, int pnum, int offset,
int len);
int ubi_io_write(const struct ubi_device *ubi, const void *buf, int pnum,
int offset, int len);
int ubi_io_sync_erase(const struct ubi_device *ubi, int pnum, int torture);
int ubi_io_is_bad(const struct ubi_device *ubi, int pnum);
int ubi_io_mark_bad(const struct ubi_device *ubi, int pnum);
int ubi_io_read_ec_hdr(const struct ubi_device *ubi, int pnum,
struct ubi_ec_hdr *ec_hdr, int verbose);
int ubi_io_write_ec_hdr(const struct ubi_device *ubi, int pnum,
struct ubi_ec_hdr *ec_hdr);
int ubi_io_read_vid_hdr(const struct ubi_device *ubi, int pnum,
struct ubi_vid_hdr *vid_hdr, int verbose);
int ubi_io_write_vid_hdr(const struct ubi_device *ubi, int pnum,
struct ubi_vid_hdr *vid_hdr);
/*
* ubi_rb_for_each_entry - walk an RB-tree.
* @rb: a pointer to type 'struct rb_node' to to use as a loop counter
* @pos: a pointer to RB-tree entry type to use as a loop counter
* @root: RB-tree's root
* @member: the name of the 'struct rb_node' within the RB-tree entry
*/
#define ubi_rb_for_each_entry(rb, pos, root, member) \
for (rb = rb_first(root), \
pos = (rb ? container_of(rb, typeof(*pos), member) : NULL); \
rb; \
rb = rb_next(rb), pos = container_of(rb, typeof(*pos), member))
/**
* ubi_zalloc_vid_hdr - allocate a volume identifier header object.
* @ubi: UBI device description object
*
* This function returns a pointer to the newly allocated and zero-filled
* volume identifier header object in case of success and %NULL in case of
* failure.
*/
static inline struct ubi_vid_hdr *ubi_zalloc_vid_hdr(const struct ubi_device *ubi)
{
void *vid_hdr;
vid_hdr = kzalloc(ubi->vid_hdr_alsize, GFP_KERNEL);
if (!vid_hdr)
return NULL;
/*
* VID headers may be stored at un-aligned flash offsets, so we shift
* the pointer.
*/
return vid_hdr + ubi->vid_hdr_shift;
}
/**
* ubi_free_vid_hdr - free a volume identifier header object.
* @ubi: UBI device description object
* @vid_hdr: the object to free
*/
static inline void ubi_free_vid_hdr(const struct ubi_device *ubi,
struct ubi_vid_hdr *vid_hdr)
{
void *p = vid_hdr;
if (!p)
return;
kfree(p - ubi->vid_hdr_shift);
}
/*
* This function is equivalent to 'ubi_io_read()', but @offset is relative to
* the beginning of the logical eraseblock, not to the beginning of the
* physical eraseblock.
*/
static inline int ubi_io_read_data(const struct ubi_device *ubi, void *buf,
int pnum, int offset, int len)
{
ubi_assert(offset >= 0);
return ubi_io_read(ubi, buf, pnum, offset + ubi->leb_start, len);
}
/*
* This function is equivalent to 'ubi_io_write()', but @offset is relative to
* the beginning of the logical eraseblock, not to the beginning of the
* physical eraseblock.
*/
static inline int ubi_io_write_data(const struct ubi_device *ubi, const void *buf,
int pnum, int offset, int len)
{
ubi_assert(offset >= 0);
return ubi_io_write(ubi, buf, pnum, offset + ubi->leb_start, len);
}
/**
* ubi_ro_mode - switch to read-only mode.
* @ubi: UBI device description object
*/
static inline void ubi_ro_mode(struct ubi_device *ubi)
{
ubi->ro_mode = 1;
ubi_warn("switch to read-only mode");
}
/**
* vol_id2idx - get table index by volume ID.
* @ubi: UBI device description object
* @vol_id: volume ID
*/
static inline int vol_id2idx(const struct ubi_device *ubi, int vol_id)
{
if (vol_id >= UBI_INTERNAL_VOL_START)
return vol_id - UBI_INTERNAL_VOL_START + ubi->vtbl_slots;
else
return vol_id;
}
/**
* idx2vol_id - get volume ID by table index.
* @ubi: UBI device description object
* @idx: table index
*/
static inline int idx2vol_id(const struct ubi_device *ubi, int idx)
{
if (idx >= ubi->vtbl_slots)
return idx - ubi->vtbl_slots + UBI_INTERNAL_VOL_START;
else
return idx;
}
#endif /* !__UBI_UBI_H__ */

348
drivers/mtd/ubi/upd.c Normal file
View File

@ -0,0 +1,348 @@
/*
* Copyright (c) International Business Machines Corp., 2006
* Copyright (c) Nokia Corporation, 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*
* Jan 2007: Alexander Schmidt, hacked per-volume update.
*/
/*
* This file contains implementation of the volume update functionality.
*
* The update operation is based on the per-volume update marker which is
* stored in the volume table. The update marker is set before the update
* starts, and removed after the update has been finished. So if the update was
* interrupted by an unclean re-boot or due to some other reasons, the update
* marker stays on the flash media and UBI finds it when it attaches the MTD
* device next time. If the update marker is set for a volume, the volume is
* treated as damaged and most I/O operations are prohibited. Only a new update
* operation is allowed.
*
* Note, in general it is possible to implement the update operation as a
* transaction with a roll-back capability.
*/
#include <linux/err.h>
#include <asm/uaccess.h>
#include <asm/div64.h>
#include "ubi.h"
/**
* set_update_marker - set update marker.
* @ubi: UBI device description object
* @vol_id: volume ID
*
* This function sets the update marker flag for volume @vol_id. Returns zero
* in case of success and a negative error code in case of failure.
*/
static int set_update_marker(struct ubi_device *ubi, int vol_id)
{
int err;
struct ubi_vtbl_record vtbl_rec;
struct ubi_volume *vol = ubi->volumes[vol_id];
dbg_msg("set update marker for volume %d", vol_id);
if (vol->upd_marker) {
ubi_assert(ubi->vtbl[vol_id].upd_marker);
dbg_msg("already set");
return 0;
}
memcpy(&vtbl_rec, &ubi->vtbl[vol_id], sizeof(struct ubi_vtbl_record));
vtbl_rec.upd_marker = 1;
err = ubi_change_vtbl_record(ubi, vol_id, &vtbl_rec);
vol->upd_marker = 1;
return err;
}
/**
* clear_update_marker - clear update marker.
* @ubi: UBI device description object
* @vol_id: volume ID
* @bytes: new data size in bytes
*
* This function clears the update marker for volume @vol_id, sets new volume
* data size and clears the "corrupted" flag (static volumes only). Returns
* zero in case of success and a negative error code in case of failure.
*/
static int clear_update_marker(struct ubi_device *ubi, int vol_id, long long bytes)
{
int err;
uint64_t tmp;
struct ubi_vtbl_record vtbl_rec;
struct ubi_volume *vol = ubi->volumes[vol_id];
dbg_msg("clear update marker for volume %d", vol_id);
memcpy(&vtbl_rec, &ubi->vtbl[vol_id], sizeof(struct ubi_vtbl_record));
ubi_assert(vol->upd_marker && vtbl_rec.upd_marker);
vtbl_rec.upd_marker = 0;
if (vol->vol_type == UBI_STATIC_VOLUME) {
vol->corrupted = 0;
vol->used_bytes = tmp = bytes;
vol->last_eb_bytes = do_div(tmp, vol->usable_leb_size);
vol->used_ebs = tmp;
if (vol->last_eb_bytes)
vol->used_ebs += 1;
else
vol->last_eb_bytes = vol->usable_leb_size;
}
err = ubi_change_vtbl_record(ubi, vol_id, &vtbl_rec);
vol->upd_marker = 0;
return err;
}
/**
* ubi_start_update - start volume update.
* @ubi: UBI device description object
* @vol_id: volume ID
* @bytes: update bytes
*
* This function starts volume update operation. If @bytes is zero, the volume
* is just wiped out. Returns zero in case of success and a negative error code
* in case of failure.
*/
int ubi_start_update(struct ubi_device *ubi, int vol_id, long long bytes)
{
int i, err;
uint64_t tmp;
struct ubi_volume *vol = ubi->volumes[vol_id];
dbg_msg("start update of volume %d, %llu bytes", vol_id, bytes);
vol->updating = 1;
err = set_update_marker(ubi, vol_id);
if (err)
return err;
/* Before updating - wipe out the volume */
for (i = 0; i < vol->reserved_pebs; i++) {
err = ubi_eba_unmap_leb(ubi, vol_id, i);
if (err)
return err;
}
if (bytes == 0) {
err = clear_update_marker(ubi, vol_id, 0);
if (err)
return err;
err = ubi_wl_flush(ubi);
if (!err)
vol->updating = 0;
}
vol->upd_buf = kmalloc(ubi->leb_size, GFP_KERNEL);
if (!vol->upd_buf)
return -ENOMEM;
tmp = bytes;
vol->upd_ebs = !!do_div(tmp, vol->usable_leb_size);
vol->upd_ebs += tmp;
vol->upd_bytes = bytes;
vol->upd_received = 0;
return 0;
}
/**
* write_leb - write update data.
* @ubi: UBI device description object
* @vol_id: volume ID
* @lnum: logical eraseblock number
* @buf: data to write
* @len: data size
* @used_ebs: how many logical eraseblocks will this volume contain (static
* volumes only)
*
* This function writes update data to corresponding logical eraseblock. In
* case of dynamic volume, this function checks if the data contains 0xFF bytes
* at the end. If yes, the 0xFF bytes are cut and not written. So if the whole
* buffer contains only 0xFF bytes, the LEB is left unmapped.
*
* The reason why we skip the trailing 0xFF bytes in case of dynamic volume is
* that we want to make sure that more data may be appended to the logical
* eraseblock in future. Indeed, writing 0xFF bytes may have side effects and
* this PEB won't be writable anymore. So if one writes the file-system image
* to the UBI volume where 0xFFs mean free space - UBI makes sure this free
* space is writable after the update.
*
* We do not do this for static volumes because they are read-only. But this
* also cannot be done because we have to store per-LEB CRC and the correct
* data length.
*
* This function returns zero in case of success and a negative error code in
* case of failure.
*/
static int write_leb(struct ubi_device *ubi, int vol_id, int lnum, void *buf,
int len, int used_ebs)
{
int err, l;
struct ubi_volume *vol = ubi->volumes[vol_id];
if (vol->vol_type == UBI_DYNAMIC_VOLUME) {
l = ALIGN(len, ubi->min_io_size);
memset(buf + len, 0xFF, l - len);
l = ubi_calc_data_len(ubi, buf, l);
if (l == 0) {
dbg_msg("all %d bytes contain 0xFF - skip", len);
return 0;
}
if (len != l)
dbg_msg("skip last %d bytes (0xFF)", len - l);
err = ubi_eba_write_leb(ubi, vol_id, lnum, buf, 0, l,
UBI_UNKNOWN);
} else {
/*
* When writing static volume, and this is the last logical
* eraseblock, the length (@len) does not have to be aligned to
* the minimal flash I/O unit. The 'ubi_eba_write_leb_st()'
* function accepts exact (unaligned) length and stores it in
* the VID header. And it takes care of proper alignment by
* padding the buffer. Here we just make sure the padding will
* contain zeros, not random trash.
*/
memset(buf + len, 0, vol->usable_leb_size - len);
err = ubi_eba_write_leb_st(ubi, vol_id, lnum, buf, len,
UBI_UNKNOWN, used_ebs);
}
return err;
}
/**
* ubi_more_update_data - write more update data.
* @vol: volume description object
* @buf: write data (user-space memory buffer)
* @count: how much bytes to write
*
* This function writes more data to the volume which is being updated. It may
* be called arbitrary number of times until all of the update data arrive.
* This function returns %0 in case of success, number of bytes written during
* the last call if the whole volume update was successfully finished, and a
* negative error code in case of failure.
*/
int ubi_more_update_data(struct ubi_device *ubi, int vol_id,
const void __user *buf, int count)
{
uint64_t tmp;
struct ubi_volume *vol = ubi->volumes[vol_id];
int lnum, offs, err = 0, len, to_write = count;
dbg_msg("write %d of %lld bytes, %lld already passed",
count, vol->upd_bytes, vol->upd_received);
if (ubi->ro_mode)
return -EROFS;
tmp = vol->upd_received;
offs = do_div(tmp, vol->usable_leb_size);
lnum = tmp;
if (vol->upd_received + count > vol->upd_bytes)
to_write = count = vol->upd_bytes - vol->upd_received;
/*
* When updating volumes, we accumulate whole logical eraseblock of
* data and write it at once.
*/
if (offs != 0) {
/*
* This is a write to the middle of the logical eraseblock. We
* copy the data to our update buffer and wait for more data or
* flush it if the whole eraseblock is written or the update
* is finished.
*/
len = vol->usable_leb_size - offs;
if (len > count)
len = count;
err = copy_from_user(vol->upd_buf + offs, buf, len);
if (err)
return -EFAULT;
if (offs + len == vol->usable_leb_size ||
vol->upd_received + len == vol->upd_bytes) {
int flush_len = offs + len;
/*
* OK, we gathered either the whole eraseblock or this
* is the last chunk, it's time to flush the buffer.
*/
ubi_assert(flush_len <= vol->usable_leb_size);
err = write_leb(ubi, vol_id, lnum, vol->upd_buf,
flush_len, vol->upd_ebs);
if (err)
return err;
}
vol->upd_received += len;
count -= len;
buf += len;
lnum += 1;
}
/*
* If we've got more to write, let's continue. At this point we know we
* are starting from the beginning of an eraseblock.
*/
while (count) {
if (count > vol->usable_leb_size)
len = vol->usable_leb_size;
else
len = count;
err = copy_from_user(vol->upd_buf, buf, len);
if (err)
return -EFAULT;
if (len == vol->usable_leb_size ||
vol->upd_received + len == vol->upd_bytes) {
err = write_leb(ubi, vol_id, lnum, vol->upd_buf, len,
vol->upd_ebs);
if (err)
break;
}
vol->upd_received += len;
count -= len;
lnum += 1;
buf += len;
}
ubi_assert(vol->upd_received <= vol->upd_bytes);
if (vol->upd_received == vol->upd_bytes) {
/* The update is finished, clear the update marker */
err = clear_update_marker(ubi, vol_id, vol->upd_bytes);
if (err)
return err;
err = ubi_wl_flush(ubi);
if (err == 0) {
err = to_write;
kfree(vol->upd_buf);
vol->updating = 0;
}
}
return err;
}

809
drivers/mtd/ubi/vmt.c Normal file
View File

@ -0,0 +1,809 @@
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*/
/*
* This file contains implementation of volume creation, deletion, updating and
* resizing.
*/
#include <linux/err.h>
#include <asm/div64.h>
#include "ubi.h"
#ifdef CONFIG_MTD_UBI_DEBUG_PARANOID
static void paranoid_check_volumes(struct ubi_device *ubi);
#else
#define paranoid_check_volumes(ubi)
#endif
static ssize_t vol_attribute_show(struct device *dev,
struct device_attribute *attr, char *buf);
/* Device attributes corresponding to files in '/<sysfs>/class/ubi/ubiX_Y' */
static struct device_attribute vol_reserved_ebs =
__ATTR(reserved_ebs, S_IRUGO, vol_attribute_show, NULL);
static struct device_attribute vol_type =
__ATTR(type, S_IRUGO, vol_attribute_show, NULL);
static struct device_attribute vol_name =
__ATTR(name, S_IRUGO, vol_attribute_show, NULL);
static struct device_attribute vol_corrupted =
__ATTR(corrupted, S_IRUGO, vol_attribute_show, NULL);
static struct device_attribute vol_alignment =
__ATTR(alignment, S_IRUGO, vol_attribute_show, NULL);
static struct device_attribute vol_usable_eb_size =
__ATTR(usable_eb_size, S_IRUGO, vol_attribute_show, NULL);
static struct device_attribute vol_data_bytes =
__ATTR(data_bytes, S_IRUGO, vol_attribute_show, NULL);
static struct device_attribute vol_upd_marker =
__ATTR(upd_marker, S_IRUGO, vol_attribute_show, NULL);
/*
* "Show" method for files in '/<sysfs>/class/ubi/ubiX_Y/'.
*
* Consider a situation:
* A. process 1 opens a sysfs file related to volume Y, say
* /<sysfs>/class/ubi/ubiX_Y/reserved_ebs;
* B. process 2 removes volume Y;
* C. process 1 starts reading the /<sysfs>/class/ubi/ubiX_Y/reserved_ebs file;
*
* What we want to do in a situation like that is to return error when the file
* is read. This is done by means of the 'removed' flag and the 'vol_lock' of
* the UBI volume description object.
*/
static ssize_t vol_attribute_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
int ret;
struct ubi_volume *vol = container_of(dev, struct ubi_volume, dev);
spin_lock(&vol->ubi->volumes_lock);
if (vol->removed) {
spin_unlock(&vol->ubi->volumes_lock);
return -ENODEV;
}
if (attr == &vol_reserved_ebs)
ret = sprintf(buf, "%d\n", vol->reserved_pebs);
else if (attr == &vol_type) {
const char *tp;
tp = vol->vol_type == UBI_DYNAMIC_VOLUME ? "dynamic" : "static";
ret = sprintf(buf, "%s\n", tp);
} else if (attr == &vol_name)
ret = sprintf(buf, "%s\n", vol->name);
else if (attr == &vol_corrupted)
ret = sprintf(buf, "%d\n", vol->corrupted);
else if (attr == &vol_alignment)
ret = sprintf(buf, "%d\n", vol->alignment);
else if (attr == &vol_usable_eb_size) {
ret = sprintf(buf, "%d\n", vol->usable_leb_size);
} else if (attr == &vol_data_bytes)
ret = sprintf(buf, "%lld\n", vol->used_bytes);
else if (attr == &vol_upd_marker)
ret = sprintf(buf, "%d\n", vol->upd_marker);
else
BUG();
spin_unlock(&vol->ubi->volumes_lock);
return ret;
}
/* Release method for volume devices */
static void vol_release(struct device *dev)
{
struct ubi_volume *vol = container_of(dev, struct ubi_volume, dev);
ubi_assert(vol->removed);
kfree(vol);
}
/**
* volume_sysfs_init - initialize sysfs for new volume.
* @ubi: UBI device description object
* @vol: volume description object
*
* This function returns zero in case of success and a negative error code in
* case of failure.
*
* Note, this function does not free allocated resources in case of failure -
* the caller does it. This is because this would cause release() here and the
* caller would oops.
*/
static int volume_sysfs_init(struct ubi_device *ubi, struct ubi_volume *vol)
{
int err;
err = device_create_file(&vol->dev, &vol_reserved_ebs);
if (err)
return err;
err = device_create_file(&vol->dev, &vol_type);
if (err)
return err;
err = device_create_file(&vol->dev, &vol_name);
if (err)
return err;
err = device_create_file(&vol->dev, &vol_corrupted);
if (err)
return err;
err = device_create_file(&vol->dev, &vol_alignment);
if (err)
return err;
err = device_create_file(&vol->dev, &vol_usable_eb_size);
if (err)
return err;
err = device_create_file(&vol->dev, &vol_data_bytes);
if (err)
return err;
err = device_create_file(&vol->dev, &vol_upd_marker);
if (err)
return err;
return 0;
}
/**
* volume_sysfs_close - close sysfs for a volume.
* @vol: volume description object
*/
static void volume_sysfs_close(struct ubi_volume *vol)
{
device_remove_file(&vol->dev, &vol_upd_marker);
device_remove_file(&vol->dev, &vol_data_bytes);
device_remove_file(&vol->dev, &vol_usable_eb_size);
device_remove_file(&vol->dev, &vol_alignment);
device_remove_file(&vol->dev, &vol_corrupted);
device_remove_file(&vol->dev, &vol_name);
device_remove_file(&vol->dev, &vol_type);
device_remove_file(&vol->dev, &vol_reserved_ebs);
device_unregister(&vol->dev);
}
/**
* ubi_create_volume - create volume.
* @ubi: UBI device description object
* @req: volume creation request
*
* This function creates volume described by @req. If @req->vol_id id
* %UBI_VOL_NUM_AUTO, this function automatically assigne ID to the new volume
* and saves it in @req->vol_id. Returns zero in case of success and a negative
* error code in case of failure.
*/
int ubi_create_volume(struct ubi_device *ubi, struct ubi_mkvol_req *req)
{
int i, err, vol_id = req->vol_id;
struct ubi_volume *vol;
struct ubi_vtbl_record vtbl_rec;
uint64_t bytes;
if (ubi->ro_mode)
return -EROFS;
vol = kzalloc(sizeof(struct ubi_volume), GFP_KERNEL);
if (!vol)
return -ENOMEM;
spin_lock(&ubi->volumes_lock);
if (vol_id == UBI_VOL_NUM_AUTO) {
/* Find unused volume ID */
dbg_msg("search for vacant volume ID");
for (i = 0; i < ubi->vtbl_slots; i++)
if (!ubi->volumes[i]) {
vol_id = i;
break;
}
if (vol_id == UBI_VOL_NUM_AUTO) {
dbg_err("out of volume IDs");
err = -ENFILE;
goto out_unlock;
}
req->vol_id = vol_id;
}
dbg_msg("volume ID %d, %llu bytes, type %d, name %s",
vol_id, (unsigned long long)req->bytes,
(int)req->vol_type, req->name);
/* Ensure that this volume does not exist */
err = -EEXIST;
if (ubi->volumes[vol_id]) {
dbg_err("volume %d already exists", vol_id);
goto out_unlock;
}
/* Ensure that the name is unique */
for (i = 0; i < ubi->vtbl_slots; i++)
if (ubi->volumes[i] &&
ubi->volumes[i]->name_len == req->name_len &&
strcmp(ubi->volumes[i]->name, req->name) == 0) {
dbg_err("volume \"%s\" exists (ID %d)", req->name, i);
goto out_unlock;
}
/* Calculate how many eraseblocks are requested */
vol->usable_leb_size = ubi->leb_size - ubi->leb_size % req->alignment;
bytes = req->bytes;
if (do_div(bytes, vol->usable_leb_size))
vol->reserved_pebs = 1;
vol->reserved_pebs += bytes;
/* Reserve physical eraseblocks */
if (vol->reserved_pebs > ubi->avail_pebs) {
dbg_err("not enough PEBs, only %d available", ubi->avail_pebs);
spin_unlock(&ubi->volumes_lock);
err = -ENOSPC;
goto out_unlock;
}
ubi->avail_pebs -= vol->reserved_pebs;
ubi->rsvd_pebs += vol->reserved_pebs;
vol->vol_id = vol_id;
vol->alignment = req->alignment;
vol->data_pad = ubi->leb_size % vol->alignment;
vol->vol_type = req->vol_type;
vol->name_len = req->name_len;
memcpy(vol->name, req->name, vol->name_len + 1);
vol->exclusive = 1;
vol->ubi = ubi;
ubi->volumes[vol_id] = vol;
spin_unlock(&ubi->volumes_lock);
/*
* Finish all pending erases because there may be some LEBs belonging
* to the same volume ID.
*/
err = ubi_wl_flush(ubi);
if (err)
goto out_acc;
vol->eba_tbl = kmalloc(vol->reserved_pebs * sizeof(int), GFP_KERNEL);
if (!vol->eba_tbl) {
err = -ENOMEM;
goto out_acc;
}
for (i = 0; i < vol->reserved_pebs; i++)
vol->eba_tbl[i] = UBI_LEB_UNMAPPED;
if (vol->vol_type == UBI_DYNAMIC_VOLUME) {
vol->used_ebs = vol->reserved_pebs;
vol->last_eb_bytes = vol->usable_leb_size;
vol->used_bytes = vol->used_ebs * vol->usable_leb_size;
} else {
bytes = vol->used_bytes;
vol->last_eb_bytes = do_div(bytes, vol->usable_leb_size);
vol->used_ebs = bytes;
if (vol->last_eb_bytes)
vol->used_ebs += 1;
else
vol->last_eb_bytes = vol->usable_leb_size;
}
/* Register character device for the volume */
cdev_init(&vol->cdev, &ubi_vol_cdev_operations);
vol->cdev.owner = THIS_MODULE;
err = cdev_add(&vol->cdev, MKDEV(ubi->major, vol_id + 1), 1);
if (err) {
ubi_err("cannot add character device for volume %d", vol_id);
goto out_mapping;
}
err = ubi_create_gluebi(ubi, vol);
if (err)
goto out_cdev;
vol->dev.release = vol_release;
vol->dev.parent = &ubi->dev;
vol->dev.devt = MKDEV(ubi->major, vol->vol_id + 1);
vol->dev.class = ubi_class;
sprintf(&vol->dev.bus_id[0], "%s_%d", ubi->ubi_name, vol->vol_id);
err = device_register(&vol->dev);
if (err)
goto out_gluebi;
err = volume_sysfs_init(ubi, vol);
if (err)
goto out_sysfs;
/* Fill volume table record */
memset(&vtbl_rec, 0, sizeof(struct ubi_vtbl_record));
vtbl_rec.reserved_pebs = cpu_to_ubi32(vol->reserved_pebs);
vtbl_rec.alignment = cpu_to_ubi32(vol->alignment);
vtbl_rec.data_pad = cpu_to_ubi32(vol->data_pad);
vtbl_rec.name_len = cpu_to_ubi16(vol->name_len);
if (vol->vol_type == UBI_DYNAMIC_VOLUME)
vtbl_rec.vol_type = UBI_VID_DYNAMIC;
else
vtbl_rec.vol_type = UBI_VID_STATIC;
memcpy(vtbl_rec.name, vol->name, vol->name_len + 1);
err = ubi_change_vtbl_record(ubi, vol_id, &vtbl_rec);
if (err)
goto out_sysfs;
spin_lock(&ubi->volumes_lock);
ubi->vol_count += 1;
vol->exclusive = 0;
spin_unlock(&ubi->volumes_lock);
paranoid_check_volumes(ubi);
return 0;
out_gluebi:
err = ubi_destroy_gluebi(vol);
out_cdev:
cdev_del(&vol->cdev);
out_mapping:
kfree(vol->eba_tbl);
out_acc:
spin_lock(&ubi->volumes_lock);
ubi->rsvd_pebs -= vol->reserved_pebs;
ubi->avail_pebs += vol->reserved_pebs;
out_unlock:
spin_unlock(&ubi->volumes_lock);
kfree(vol);
return err;
/*
* We are registered, so @vol is destroyed in the release function and
* we have to de-initialize differently.
*/
out_sysfs:
err = ubi_destroy_gluebi(vol);
cdev_del(&vol->cdev);
kfree(vol->eba_tbl);
spin_lock(&ubi->volumes_lock);
ubi->rsvd_pebs -= vol->reserved_pebs;
ubi->avail_pebs += vol->reserved_pebs;
spin_unlock(&ubi->volumes_lock);
volume_sysfs_close(vol);
return err;
}
/**
* ubi_remove_volume - remove volume.
* @desc: volume descriptor
*
* This function removes volume described by @desc. The volume has to be opened
* in "exclusive" mode. Returns zero in case of success and a negative error
* code in case of failure.
*/
int ubi_remove_volume(struct ubi_volume_desc *desc)
{
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
int i, err, vol_id = vol->vol_id, reserved_pebs = vol->reserved_pebs;
dbg_msg("remove UBI volume %d", vol_id);
ubi_assert(desc->mode == UBI_EXCLUSIVE);
ubi_assert(vol == ubi->volumes[vol_id]);
if (ubi->ro_mode)
return -EROFS;
err = ubi_destroy_gluebi(vol);
if (err)
return err;
err = ubi_change_vtbl_record(ubi, vol_id, NULL);
if (err)
return err;
for (i = 0; i < vol->reserved_pebs; i++) {
err = ubi_eba_unmap_leb(ubi, vol_id, i);
if (err)
return err;
}
spin_lock(&ubi->volumes_lock);
vol->removed = 1;
ubi->volumes[vol_id] = NULL;
spin_unlock(&ubi->volumes_lock);
kfree(vol->eba_tbl);
vol->eba_tbl = NULL;
cdev_del(&vol->cdev);
volume_sysfs_close(vol);
kfree(desc);
spin_lock(&ubi->volumes_lock);
ubi->rsvd_pebs -= reserved_pebs;
ubi->avail_pebs += reserved_pebs;
i = ubi->beb_rsvd_level - ubi->beb_rsvd_pebs;
if (i > 0) {
i = ubi->avail_pebs >= i ? i : ubi->avail_pebs;
ubi->avail_pebs -= i;
ubi->rsvd_pebs += i;
ubi->beb_rsvd_pebs += i;
if (i > 0)
ubi_msg("reserve more %d PEBs", i);
}
ubi->vol_count -= 1;
spin_unlock(&ubi->volumes_lock);
paranoid_check_volumes(ubi);
module_put(THIS_MODULE);
return 0;
}
/**
* ubi_resize_volume - re-size volume.
* @desc: volume descriptor
* @reserved_pebs: new size in physical eraseblocks
*
* This function returns zero in case of success, and a negative error code in
* case of failure.
*/
int ubi_resize_volume(struct ubi_volume_desc *desc, int reserved_pebs)
{
int i, err, pebs, *new_mapping;
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
struct ubi_vtbl_record vtbl_rec;
int vol_id = vol->vol_id;
if (ubi->ro_mode)
return -EROFS;
dbg_msg("re-size volume %d to from %d to %d PEBs",
vol_id, vol->reserved_pebs, reserved_pebs);
ubi_assert(desc->mode == UBI_EXCLUSIVE);
ubi_assert(vol == ubi->volumes[vol_id]);
if (vol->vol_type == UBI_STATIC_VOLUME &&
reserved_pebs < vol->used_ebs) {
dbg_err("too small size %d, %d LEBs contain data",
reserved_pebs, vol->used_ebs);
return -EINVAL;
}
/* If the size is the same, we have nothing to do */
if (reserved_pebs == vol->reserved_pebs)
return 0;
new_mapping = kmalloc(reserved_pebs * sizeof(int), GFP_KERNEL);
if (!new_mapping)
return -ENOMEM;
for (i = 0; i < reserved_pebs; i++)
new_mapping[i] = UBI_LEB_UNMAPPED;
/* Reserve physical eraseblocks */
pebs = reserved_pebs - vol->reserved_pebs;
if (pebs > 0) {
spin_lock(&ubi->volumes_lock);
if (pebs > ubi->avail_pebs) {
dbg_err("not enough PEBs: requested %d, available %d",
pebs, ubi->avail_pebs);
spin_unlock(&ubi->volumes_lock);
err = -ENOSPC;
goto out_free;
}
ubi->avail_pebs -= pebs;
ubi->rsvd_pebs += pebs;
for (i = 0; i < vol->reserved_pebs; i++)
new_mapping[i] = vol->eba_tbl[i];
kfree(vol->eba_tbl);
vol->eba_tbl = new_mapping;
spin_unlock(&ubi->volumes_lock);
}
/* Change volume table record */
memcpy(&vtbl_rec, &ubi->vtbl[vol_id], sizeof(struct ubi_vtbl_record));
vtbl_rec.reserved_pebs = cpu_to_ubi32(reserved_pebs);
err = ubi_change_vtbl_record(ubi, vol_id, &vtbl_rec);
if (err)
goto out_acc;
if (pebs < 0) {
for (i = 0; i < -pebs; i++) {
err = ubi_eba_unmap_leb(ubi, vol_id, reserved_pebs + i);
if (err)
goto out_acc;
}
spin_lock(&ubi->volumes_lock);
ubi->rsvd_pebs += pebs;
ubi->avail_pebs -= pebs;
pebs = ubi->beb_rsvd_level - ubi->beb_rsvd_pebs;
if (pebs > 0) {
pebs = ubi->avail_pebs >= pebs ? pebs : ubi->avail_pebs;
ubi->avail_pebs -= pebs;
ubi->rsvd_pebs += pebs;
ubi->beb_rsvd_pebs += pebs;
if (pebs > 0)
ubi_msg("reserve more %d PEBs", pebs);
}
for (i = 0; i < reserved_pebs; i++)
new_mapping[i] = vol->eba_tbl[i];
kfree(vol->eba_tbl);
vol->eba_tbl = new_mapping;
spin_unlock(&ubi->volumes_lock);
}
vol->reserved_pebs = reserved_pebs;
if (vol->vol_type == UBI_DYNAMIC_VOLUME) {
vol->used_ebs = reserved_pebs;
vol->last_eb_bytes = vol->usable_leb_size;
vol->used_bytes = vol->used_ebs * vol->usable_leb_size;
}
paranoid_check_volumes(ubi);
return 0;
out_acc:
if (pebs > 0) {
spin_lock(&ubi->volumes_lock);
ubi->rsvd_pebs -= pebs;
ubi->avail_pebs += pebs;
spin_unlock(&ubi->volumes_lock);
}
out_free:
kfree(new_mapping);
return err;
}
/**
* ubi_add_volume - add volume.
* @ubi: UBI device description object
* @vol_id: volume ID
*
* This function adds an existin volume and initializes all its data
* structures. Returnes zero in case of success and a negative error code in
* case of failure.
*/
int ubi_add_volume(struct ubi_device *ubi, int vol_id)
{
int err;
struct ubi_volume *vol = ubi->volumes[vol_id];
dbg_msg("add volume %d", vol_id);
ubi_dbg_dump_vol_info(vol);
ubi_assert(vol);
/* Register character device for the volume */
cdev_init(&vol->cdev, &ubi_vol_cdev_operations);
vol->cdev.owner = THIS_MODULE;
err = cdev_add(&vol->cdev, MKDEV(ubi->major, vol->vol_id + 1), 1);
if (err) {
ubi_err("cannot add character device for volume %d", vol_id);
return err;
}
err = ubi_create_gluebi(ubi, vol);
if (err)
goto out_cdev;
vol->dev.release = vol_release;
vol->dev.parent = &ubi->dev;
vol->dev.devt = MKDEV(ubi->major, vol->vol_id + 1);
vol->dev.class = ubi_class;
sprintf(&vol->dev.bus_id[0], "%s_%d", ubi->ubi_name, vol->vol_id);
err = device_register(&vol->dev);
if (err)
goto out_gluebi;
err = volume_sysfs_init(ubi, vol);
if (err) {
cdev_del(&vol->cdev);
err = ubi_destroy_gluebi(vol);
volume_sysfs_close(vol);
return err;
}
paranoid_check_volumes(ubi);
return 0;
out_gluebi:
err = ubi_destroy_gluebi(vol);
out_cdev:
cdev_del(&vol->cdev);
return err;
}
/**
* ubi_free_volume - free volume.
* @ubi: UBI device description object
* @vol_id: volume ID
*
* This function frees all resources for volume @vol_id but does not remove it.
* Used only when the UBI device is detached.
*/
void ubi_free_volume(struct ubi_device *ubi, int vol_id)
{
int err;
struct ubi_volume *vol = ubi->volumes[vol_id];
dbg_msg("free volume %d", vol_id);
ubi_assert(vol);
vol->removed = 1;
err = ubi_destroy_gluebi(vol);
ubi->volumes[vol_id] = NULL;
cdev_del(&vol->cdev);
volume_sysfs_close(vol);
}
#ifdef CONFIG_MTD_UBI_DEBUG_PARANOID
/**
* paranoid_check_volume - check volume information.
* @ubi: UBI device description object
* @vol_id: volume ID
*/
static void paranoid_check_volume(const struct ubi_device *ubi, int vol_id)
{
int idx = vol_id2idx(ubi, vol_id);
int reserved_pebs, alignment, data_pad, vol_type, name_len, upd_marker;
const struct ubi_volume *vol = ubi->volumes[idx];
long long n;
const char *name;
reserved_pebs = ubi32_to_cpu(ubi->vtbl[vol_id].reserved_pebs);
if (!vol) {
if (reserved_pebs) {
ubi_err("no volume info, but volume exists");
goto fail;
}
return;
}
if (vol->reserved_pebs < 0 || vol->alignment < 0 || vol->data_pad < 0 ||
vol->name_len < 0) {
ubi_err("negative values");
goto fail;
}
if (vol->alignment > ubi->leb_size || vol->alignment == 0) {
ubi_err("bad alignment");
goto fail;
}
n = vol->alignment % ubi->min_io_size;
if (vol->alignment != 1 && n) {
ubi_err("alignment is not multiple of min I/O unit");
goto fail;
}
n = ubi->leb_size % vol->alignment;
if (vol->data_pad != n) {
ubi_err("bad data_pad, has to be %lld", n);
goto fail;
}
if (vol->vol_type != UBI_DYNAMIC_VOLUME &&
vol->vol_type != UBI_STATIC_VOLUME) {
ubi_err("bad vol_type");
goto fail;
}
if (vol->upd_marker != 0 && vol->upd_marker != 1) {
ubi_err("bad upd_marker");
goto fail;
}
if (vol->upd_marker && vol->corrupted) {
dbg_err("update marker and corrupted simultaneously");
goto fail;
}
if (vol->reserved_pebs > ubi->good_peb_count) {
ubi_err("too large reserved_pebs");
goto fail;
}
n = ubi->leb_size - vol->data_pad;
if (vol->usable_leb_size != ubi->leb_size - vol->data_pad) {
ubi_err("bad usable_leb_size, has to be %lld", n);
goto fail;
}
if (vol->name_len > UBI_VOL_NAME_MAX) {
ubi_err("too long volume name, max is %d", UBI_VOL_NAME_MAX);
goto fail;
}
if (!vol->name) {
ubi_err("NULL volume name");
goto fail;
}
n = strnlen(vol->name, vol->name_len + 1);
if (n != vol->name_len) {
ubi_err("bad name_len %lld", n);
goto fail;
}
n = vol->used_ebs * vol->usable_leb_size;
if (vol->vol_type == UBI_DYNAMIC_VOLUME) {
if (vol->corrupted != 0) {
ubi_err("corrupted dynamic volume");
goto fail;
}
if (vol->used_ebs != vol->reserved_pebs) {
ubi_err("bad used_ebs");
goto fail;
}
if (vol->last_eb_bytes != vol->usable_leb_size) {
ubi_err("bad last_eb_bytes");
goto fail;
}
if (vol->used_bytes != n) {
ubi_err("bad used_bytes");
goto fail;
}
} else {
if (vol->corrupted != 0 && vol->corrupted != 1) {
ubi_err("bad corrupted");
goto fail;
}
if (vol->used_ebs < 0 || vol->used_ebs > vol->reserved_pebs) {
ubi_err("bad used_ebs");
goto fail;
}
if (vol->last_eb_bytes < 0 ||
vol->last_eb_bytes > vol->usable_leb_size) {
ubi_err("bad last_eb_bytes");
goto fail;
}
if (vol->used_bytes < 0 || vol->used_bytes > n ||
vol->used_bytes < n - vol->usable_leb_size) {
ubi_err("bad used_bytes");
goto fail;
}
}
alignment = ubi32_to_cpu(ubi->vtbl[vol_id].alignment);
data_pad = ubi32_to_cpu(ubi->vtbl[vol_id].data_pad);
name_len = ubi16_to_cpu(ubi->vtbl[vol_id].name_len);
upd_marker = ubi->vtbl[vol_id].upd_marker;
name = &ubi->vtbl[vol_id].name[0];
if (ubi->vtbl[vol_id].vol_type == UBI_VID_DYNAMIC)
vol_type = UBI_DYNAMIC_VOLUME;
else
vol_type = UBI_STATIC_VOLUME;
if (alignment != vol->alignment || data_pad != vol->data_pad ||
upd_marker != vol->upd_marker || vol_type != vol->vol_type ||
name_len!= vol->name_len || strncmp(name, vol->name, name_len)) {
ubi_err("volume info is different");
goto fail;
}
return;
fail:
ubi_err("paranoid check failed");
ubi_dbg_dump_vol_info(vol);
ubi_dbg_dump_vtbl_record(&ubi->vtbl[vol_id], vol_id);
BUG();
}
/**
* paranoid_check_volumes - check information about all volumes.
* @ubi: UBI device description object
*/
static void paranoid_check_volumes(struct ubi_device *ubi)
{
int i;
mutex_lock(&ubi->vtbl_mutex);
spin_lock(&ubi->volumes_lock);
for (i = 0; i < ubi->vtbl_slots; i++)
paranoid_check_volume(ubi, i);
spin_unlock(&ubi->volumes_lock);
mutex_unlock(&ubi->vtbl_mutex);
}
#endif

809
drivers/mtd/ubi/vtbl.c Normal file
View File

@ -0,0 +1,809 @@
/*
* Copyright (c) International Business Machines Corp., 2006
* Copyright (c) Nokia Corporation, 2006, 2007
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*/
/*
* This file includes volume table manipulation code. The volume table is an
* on-flash table containing volume meta-data like name, number of reserved
* physical eraseblocks, type, etc. The volume table is stored in the so-called
* "layout volume".
*
* The layout volume is an internal volume which is organized as follows. It
* consists of two logical eraseblocks - LEB 0 and LEB 1. Each logical
* eraseblock stores one volume table copy, i.e. LEB 0 and LEB 1 duplicate each
* other. This redundancy guarantees robustness to unclean reboots. The volume
* table is basically an array of volume table records. Each record contains
* full information about the volume and protected by a CRC checksum.
*
* The volume table is changed, it is first changed in RAM. Then LEB 0 is
* erased, and the updated volume table is written back to LEB 0. Then same for
* LEB 1. This scheme guarantees recoverability from unclean reboots.
*
* In this UBI implementation the on-flash volume table does not contain any
* information about how many data static volumes contain. This information may
* be found from the scanning data.
*
* But it would still be beneficial to store this information in the volume
* table. For example, suppose we have a static volume X, and all its physical
* eraseblocks became bad for some reasons. Suppose we are attaching the
* corresponding MTD device, the scanning has found no logical eraseblocks
* corresponding to the volume X. According to the volume table volume X does
* exist. So we don't know whether it is just empty or all its physical
* eraseblocks went bad. So we cannot alarm the user about this corruption.
*
* The volume table also stores so-called "update marker", which is used for
* volume updates. Before updating the volume, the update marker is set, and
* after the update operation is finished, the update marker is cleared. So if
* the update operation was interrupted (e.g. by an unclean reboot) - the
* update marker is still there and we know that the volume's contents is
* damaged.
*/
#include <linux/crc32.h>
#include <linux/err.h>
#include <asm/div64.h>
#include "ubi.h"
#ifdef CONFIG_MTD_UBI_DEBUG_PARANOID
static void paranoid_vtbl_check(const struct ubi_device *ubi);
#else
#define paranoid_vtbl_check(ubi)
#endif
/* Empty volume table record */
static struct ubi_vtbl_record empty_vtbl_record;
/**
* ubi_change_vtbl_record - change volume table record.
* @ubi: UBI device description object
* @idx: table index to change
* @vtbl_rec: new volume table record
*
* This function changes volume table record @idx. If @vtbl_rec is %NULL, empty
* volume table record is written. The caller does not have to calculate CRC of
* the record as it is done by this function. Returns zero in case of success
* and a negative error code in case of failure.
*/
int ubi_change_vtbl_record(struct ubi_device *ubi, int idx,
struct ubi_vtbl_record *vtbl_rec)
{
int i, err;
uint32_t crc;
ubi_assert(idx >= 0 && idx < ubi->vtbl_slots);
if (!vtbl_rec)
vtbl_rec = &empty_vtbl_record;
else {
crc = crc32(UBI_CRC32_INIT, vtbl_rec, UBI_VTBL_RECORD_SIZE_CRC);
vtbl_rec->crc = cpu_to_ubi32(crc);
}
dbg_msg("change record %d", idx);
ubi_dbg_dump_vtbl_record(vtbl_rec, idx);
mutex_lock(&ubi->vtbl_mutex);
memcpy(&ubi->vtbl[idx], vtbl_rec, sizeof(struct ubi_vtbl_record));
for (i = 0; i < UBI_LAYOUT_VOLUME_EBS; i++) {
err = ubi_eba_unmap_leb(ubi, UBI_LAYOUT_VOL_ID, i);
if (err) {
mutex_unlock(&ubi->vtbl_mutex);
return err;
}
err = ubi_eba_write_leb(ubi, UBI_LAYOUT_VOL_ID, i, ubi->vtbl, 0,
ubi->vtbl_size, UBI_LONGTERM);
if (err) {
mutex_unlock(&ubi->vtbl_mutex);
return err;
}
}
paranoid_vtbl_check(ubi);
mutex_unlock(&ubi->vtbl_mutex);
return ubi_wl_flush(ubi);
}
/**
* vol_til_check - check if volume table is not corrupted and contains sensible
* data.
*
* @ubi: UBI device description object
* @vtbl: volume table
*
* This function returns zero if @vtbl is all right, %1 if CRC is incorrect,
* and %-EINVAL if it contains inconsistent data.
*/
static int vtbl_check(const struct ubi_device *ubi,
const struct ubi_vtbl_record *vtbl)
{
int i, n, reserved_pebs, alignment, data_pad, vol_type, name_len;
int upd_marker;
uint32_t crc;
const char *name;
for (i = 0; i < ubi->vtbl_slots; i++) {
cond_resched();
reserved_pebs = ubi32_to_cpu(vtbl[i].reserved_pebs);
alignment = ubi32_to_cpu(vtbl[i].alignment);
data_pad = ubi32_to_cpu(vtbl[i].data_pad);
upd_marker = vtbl[i].upd_marker;
vol_type = vtbl[i].vol_type;
name_len = ubi16_to_cpu(vtbl[i].name_len);
name = &vtbl[i].name[0];
crc = crc32(UBI_CRC32_INIT, &vtbl[i], UBI_VTBL_RECORD_SIZE_CRC);
if (ubi32_to_cpu(vtbl[i].crc) != crc) {
ubi_err("bad CRC at record %u: %#08x, not %#08x",
i, crc, ubi32_to_cpu(vtbl[i].crc));
ubi_dbg_dump_vtbl_record(&vtbl[i], i);
return 1;
}
if (reserved_pebs == 0) {
if (memcmp(&vtbl[i], &empty_vtbl_record,
UBI_VTBL_RECORD_SIZE)) {
dbg_err("bad empty record");
goto bad;
}
continue;
}
if (reserved_pebs < 0 || alignment < 0 || data_pad < 0 ||
name_len < 0) {
dbg_err("negative values");
goto bad;
}
if (alignment > ubi->leb_size || alignment == 0) {
dbg_err("bad alignment");
goto bad;
}
n = alignment % ubi->min_io_size;
if (alignment != 1 && n) {
dbg_err("alignment is not multiple of min I/O unit");
goto bad;
}
n = ubi->leb_size % alignment;
if (data_pad != n) {
dbg_err("bad data_pad, has to be %d", n);
goto bad;
}
if (vol_type != UBI_VID_DYNAMIC && vol_type != UBI_VID_STATIC) {
dbg_err("bad vol_type");
goto bad;
}
if (upd_marker != 0 && upd_marker != 1) {
dbg_err("bad upd_marker");
goto bad;
}
if (reserved_pebs > ubi->good_peb_count) {
dbg_err("too large reserved_pebs, good PEBs %d",
ubi->good_peb_count);
goto bad;
}
if (name_len > UBI_VOL_NAME_MAX) {
dbg_err("too long volume name, max %d",
UBI_VOL_NAME_MAX);
goto bad;
}
if (name[0] == '\0') {
dbg_err("NULL volume name");
goto bad;
}
if (name_len != strnlen(name, name_len + 1)) {
dbg_err("bad name_len");
goto bad;
}
}
/* Checks that all names are unique */
for (i = 0; i < ubi->vtbl_slots - 1; i++) {
for (n = i + 1; n < ubi->vtbl_slots; n++) {
int len1 = ubi16_to_cpu(vtbl[i].name_len);
int len2 = ubi16_to_cpu(vtbl[n].name_len);
if (len1 > 0 && len1 == len2 &&
!strncmp(vtbl[i].name, vtbl[n].name, len1)) {
ubi_err("volumes %d and %d have the same name"
" \"%s\"", i, n, vtbl[i].name);
ubi_dbg_dump_vtbl_record(&vtbl[i], i);
ubi_dbg_dump_vtbl_record(&vtbl[n], n);
return -EINVAL;
}
}
}
return 0;
bad:
ubi_err("volume table check failed, record %d", i);
ubi_dbg_dump_vtbl_record(&vtbl[i], i);
return -EINVAL;
}
/**
* create_vtbl - create a copy of volume table.
* @ubi: UBI device description object
* @si: scanning information
* @copy: number of the volume table copy
* @vtbl: contents of the volume table
*
* This function returns zero in case of success and a negative error code in
* case of failure.
*/
static int create_vtbl(const struct ubi_device *ubi, struct ubi_scan_info *si,
int copy, void *vtbl)
{
int err, tries = 0;
static struct ubi_vid_hdr *vid_hdr;
struct ubi_scan_volume *sv;
struct ubi_scan_leb *new_seb, *old_seb = NULL;
ubi_msg("create volume table (copy #%d)", copy + 1);
vid_hdr = ubi_zalloc_vid_hdr(ubi);
if (!vid_hdr)
return -ENOMEM;
/*
* Check if there is a logical eraseblock which would have to contain
* this volume table copy was found during scanning. It has to be wiped
* out.
*/
sv = ubi_scan_find_sv(si, UBI_LAYOUT_VOL_ID);
if (sv)
old_seb = ubi_scan_find_seb(sv, copy);
retry:
new_seb = ubi_scan_get_free_peb(ubi, si);
if (IS_ERR(new_seb)) {
err = PTR_ERR(new_seb);
goto out_free;
}
vid_hdr->vol_type = UBI_VID_DYNAMIC;
vid_hdr->vol_id = cpu_to_ubi32(UBI_LAYOUT_VOL_ID);
vid_hdr->compat = UBI_LAYOUT_VOLUME_COMPAT;
vid_hdr->data_size = vid_hdr->used_ebs =
vid_hdr->data_pad = cpu_to_ubi32(0);
vid_hdr->lnum = cpu_to_ubi32(copy);
vid_hdr->sqnum = cpu_to_ubi64(++si->max_sqnum);
vid_hdr->leb_ver = cpu_to_ubi32(old_seb ? old_seb->leb_ver + 1: 0);
/* The EC header is already there, write the VID header */
err = ubi_io_write_vid_hdr(ubi, new_seb->pnum, vid_hdr);
if (err)
goto write_error;
/* Write the layout volume contents */
err = ubi_io_write_data(ubi, vtbl, new_seb->pnum, 0, ubi->vtbl_size);
if (err)
goto write_error;
/*
* And add it to the scanning information. Don't delete the old
* @old_seb as it will be deleted and freed in 'ubi_scan_add_used()'.
*/
err = ubi_scan_add_used(ubi, si, new_seb->pnum, new_seb->ec,
vid_hdr, 0);
kfree(new_seb);
ubi_free_vid_hdr(ubi, vid_hdr);
return err;
write_error:
kfree(new_seb);
/* May be this physical eraseblock went bad, try to pick another one */
if (++tries <= 5) {
err = ubi_scan_add_to_list(si, new_seb->pnum, new_seb->ec,
&si->corr);
if (!err)
goto retry;
}
out_free:
ubi_free_vid_hdr(ubi, vid_hdr);
return err;
}
/**
* process_lvol - process the layout volume.
* @ubi: UBI device description object
* @si: scanning information
* @sv: layout volume scanning information
*
* This function is responsible for reading the layout volume, ensuring it is
* not corrupted, and recovering from corruptions if needed. Returns volume
* table in case of success and a negative error code in case of failure.
*/
static struct ubi_vtbl_record *process_lvol(const struct ubi_device *ubi,
struct ubi_scan_info *si,
struct ubi_scan_volume *sv)
{
int err;
struct rb_node *rb;
struct ubi_scan_leb *seb;
struct ubi_vtbl_record *leb[UBI_LAYOUT_VOLUME_EBS] = { NULL, NULL };
int leb_corrupted[UBI_LAYOUT_VOLUME_EBS] = {1, 1};
/*
* UBI goes through the following steps when it changes the layout
* volume:
* a. erase LEB 0;
* b. write new data to LEB 0;
* c. erase LEB 1;
* d. write new data to LEB 1.
*
* Before the change, both LEBs contain the same data.
*
* Due to unclean reboots, the contents of LEB 0 may be lost, but there
* should LEB 1. So it is OK if LEB 0 is corrupted while LEB 1 is not.
* Similarly, LEB 1 may be lost, but there should be LEB 0. And
* finally, unclean reboots may result in a situation when neither LEB
* 0 nor LEB 1 are corrupted, but they are different. In this case, LEB
* 0 contains more recent information.
*
* So the plan is to first check LEB 0. Then
* a. if LEB 0 is OK, it must be containing the most resent data; then
* we compare it with LEB 1, and if they are different, we copy LEB
* 0 to LEB 1;
* b. if LEB 0 is corrupted, but LEB 1 has to be OK, and we copy LEB 1
* to LEB 0.
*/
dbg_msg("check layout volume");
/* Read both LEB 0 and LEB 1 into memory */
ubi_rb_for_each_entry(rb, seb, &sv->root, u.rb) {
leb[seb->lnum] = kzalloc(ubi->vtbl_size, GFP_KERNEL);
if (!leb[seb->lnum]) {
err = -ENOMEM;
goto out_free;
}
err = ubi_io_read_data(ubi, leb[seb->lnum], seb->pnum, 0,
ubi->vtbl_size);
if (err == UBI_IO_BITFLIPS || err == -EBADMSG)
/* Scrub the PEB later */
seb->scrub = 1;
else if (err)
goto out_free;
}
err = -EINVAL;
if (leb[0]) {
leb_corrupted[0] = vtbl_check(ubi, leb[0]);
if (leb_corrupted[0] < 0)
goto out_free;
}
if (!leb_corrupted[0]) {
/* LEB 0 is OK */
if (leb[1])
leb_corrupted[1] = memcmp(leb[0], leb[1], ubi->vtbl_size);
if (leb_corrupted[1]) {
ubi_warn("volume table copy #2 is corrupted");
err = create_vtbl(ubi, si, 1, leb[0]);
if (err)
goto out_free;
ubi_msg("volume table was restored");
}
/* Both LEB 1 and LEB 2 are OK and consistent */
kfree(leb[1]);
return leb[0];
} else {
/* LEB 0 is corrupted or does not exist */
if (leb[1]) {
leb_corrupted[1] = vtbl_check(ubi, leb[1]);
if (leb_corrupted[1] < 0)
goto out_free;
}
if (leb_corrupted[1]) {
/* Both LEB 0 and LEB 1 are corrupted */
ubi_err("both volume tables are corrupted");
goto out_free;
}
ubi_warn("volume table copy #1 is corrupted");
err = create_vtbl(ubi, si, 0, leb[1]);
if (err)
goto out_free;
ubi_msg("volume table was restored");
kfree(leb[0]);
return leb[1];
}
out_free:
kfree(leb[0]);
kfree(leb[1]);
return ERR_PTR(err);
}
/**
* create_empty_lvol - create empty layout volume.
* @ubi: UBI device description object
* @si: scanning information
*
* This function returns volume table contents in case of success and a
* negative error code in case of failure.
*/
static struct ubi_vtbl_record *create_empty_lvol(const struct ubi_device *ubi,
struct ubi_scan_info *si)
{
int i;
struct ubi_vtbl_record *vtbl;
vtbl = kzalloc(ubi->vtbl_size, GFP_KERNEL);
if (!vtbl)
return ERR_PTR(-ENOMEM);
for (i = 0; i < ubi->vtbl_slots; i++)
memcpy(&vtbl[i], &empty_vtbl_record, UBI_VTBL_RECORD_SIZE);
for (i = 0; i < UBI_LAYOUT_VOLUME_EBS; i++) {
int err;
err = create_vtbl(ubi, si, i, vtbl);
if (err) {
kfree(vtbl);
return ERR_PTR(err);
}
}
return vtbl;
}
/**
* init_volumes - initialize volume information for existing volumes.
* @ubi: UBI device description object
* @si: scanning information
* @vtbl: volume table
*
* This function allocates volume description objects for existing volumes.
* Returns zero in case of success and a negative error code in case of
* failure.
*/
static int init_volumes(struct ubi_device *ubi, const struct ubi_scan_info *si,
const struct ubi_vtbl_record *vtbl)
{
int i, reserved_pebs = 0;
struct ubi_scan_volume *sv;
struct ubi_volume *vol;
for (i = 0; i < ubi->vtbl_slots; i++) {
cond_resched();
if (ubi32_to_cpu(vtbl[i].reserved_pebs) == 0)
continue; /* Empty record */
vol = kzalloc(sizeof(struct ubi_volume), GFP_KERNEL);
if (!vol)
return -ENOMEM;
vol->reserved_pebs = ubi32_to_cpu(vtbl[i].reserved_pebs);
vol->alignment = ubi32_to_cpu(vtbl[i].alignment);
vol->data_pad = ubi32_to_cpu(vtbl[i].data_pad);
vol->vol_type = vtbl[i].vol_type == UBI_VID_DYNAMIC ?
UBI_DYNAMIC_VOLUME : UBI_STATIC_VOLUME;
vol->name_len = ubi16_to_cpu(vtbl[i].name_len);
vol->usable_leb_size = ubi->leb_size - vol->data_pad;
memcpy(vol->name, vtbl[i].name, vol->name_len);
vol->name[vol->name_len] = '\0';
vol->vol_id = i;
ubi_assert(!ubi->volumes[i]);
ubi->volumes[i] = vol;
ubi->vol_count += 1;
vol->ubi = ubi;
reserved_pebs += vol->reserved_pebs;
/*
* In case of dynamic volume UBI knows nothing about how many
* data is stored there. So assume the whole volume is used.
*/
if (vol->vol_type == UBI_DYNAMIC_VOLUME) {
vol->used_ebs = vol->reserved_pebs;
vol->last_eb_bytes = vol->usable_leb_size;
vol->used_bytes = vol->used_ebs * vol->usable_leb_size;
continue;
}
/* Static volumes only */
sv = ubi_scan_find_sv(si, i);
if (!sv) {
/*
* No eraseblocks belonging to this volume found. We
* don't actually know whether this static volume is
* completely corrupted or just contains no data. And
* we cannot know this as long as data size is not
* stored on flash. So we just assume the volume is
* empty. FIXME: this should be handled.
*/
continue;
}
if (sv->leb_count != sv->used_ebs) {
/*
* We found a static volume which misses several
* eraseblocks. Treat it as corrupted.
*/
ubi_warn("static volume %d misses %d LEBs - corrupted",
sv->vol_id, sv->used_ebs - sv->leb_count);
vol->corrupted = 1;
continue;
}
vol->used_ebs = sv->used_ebs;
vol->used_bytes = (vol->used_ebs - 1) * vol->usable_leb_size;
vol->used_bytes += sv->last_data_size;
vol->last_eb_bytes = sv->last_data_size;
}
vol = kzalloc(sizeof(struct ubi_volume), GFP_KERNEL);
if (!vol)
return -ENOMEM;
vol->reserved_pebs = UBI_LAYOUT_VOLUME_EBS;
vol->alignment = 1;
vol->vol_type = UBI_DYNAMIC_VOLUME;
vol->name_len = sizeof(UBI_LAYOUT_VOLUME_NAME) - 1;
memcpy(vol->name, UBI_LAYOUT_VOLUME_NAME, vol->name_len + 1);
vol->usable_leb_size = ubi->leb_size;
vol->used_ebs = vol->reserved_pebs;
vol->last_eb_bytes = vol->reserved_pebs;
vol->used_bytes = vol->used_ebs * (ubi->leb_size - vol->data_pad);
vol->vol_id = UBI_LAYOUT_VOL_ID;
ubi_assert(!ubi->volumes[i]);
ubi->volumes[vol_id2idx(ubi, vol->vol_id)] = vol;
reserved_pebs += vol->reserved_pebs;
ubi->vol_count += 1;
vol->ubi = ubi;
if (reserved_pebs > ubi->avail_pebs)
ubi_err("not enough PEBs, required %d, available %d",
reserved_pebs, ubi->avail_pebs);
ubi->rsvd_pebs += reserved_pebs;
ubi->avail_pebs -= reserved_pebs;
return 0;
}
/**
* check_sv - check volume scanning information.
* @vol: UBI volume description object
* @sv: volume scanning information
*
* This function returns zero if the volume scanning information is consistent
* to the data read from the volume tabla, and %-EINVAL if not.
*/
static int check_sv(const struct ubi_volume *vol,
const struct ubi_scan_volume *sv)
{
if (sv->highest_lnum >= vol->reserved_pebs) {
dbg_err("bad highest_lnum");
goto bad;
}
if (sv->leb_count > vol->reserved_pebs) {
dbg_err("bad leb_count");
goto bad;
}
if (sv->vol_type != vol->vol_type) {
dbg_err("bad vol_type");
goto bad;
}
if (sv->used_ebs > vol->reserved_pebs) {
dbg_err("bad used_ebs");
goto bad;
}
if (sv->data_pad != vol->data_pad) {
dbg_err("bad data_pad");
goto bad;
}
return 0;
bad:
ubi_err("bad scanning information");
ubi_dbg_dump_sv(sv);
ubi_dbg_dump_vol_info(vol);
return -EINVAL;
}
/**
* check_scanning_info - check that scanning information.
* @ubi: UBI device description object
* @si: scanning information
*
* Even though we protect on-flash data by CRC checksums, we still don't trust
* the media. This function ensures that scanning information is consistent to
* the information read from the volume table. Returns zero if the scanning
* information is OK and %-EINVAL if it is not.
*/
static int check_scanning_info(const struct ubi_device *ubi,
struct ubi_scan_info *si)
{
int err, i;
struct ubi_scan_volume *sv;
struct ubi_volume *vol;
if (si->vols_found > UBI_INT_VOL_COUNT + ubi->vtbl_slots) {
ubi_err("scanning found %d volumes, maximum is %d + %d",
si->vols_found, UBI_INT_VOL_COUNT, ubi->vtbl_slots);
return -EINVAL;
}
if (si->highest_vol_id >= ubi->vtbl_slots + UBI_INT_VOL_COUNT&&
si->highest_vol_id < UBI_INTERNAL_VOL_START) {
ubi_err("too large volume ID %d found by scanning",
si->highest_vol_id);
return -EINVAL;
}
for (i = 0; i < ubi->vtbl_slots + UBI_INT_VOL_COUNT; i++) {
cond_resched();
sv = ubi_scan_find_sv(si, i);
vol = ubi->volumes[i];
if (!vol) {
if (sv)
ubi_scan_rm_volume(si, sv);
continue;
}
if (vol->reserved_pebs == 0) {
ubi_assert(i < ubi->vtbl_slots);
if (!sv)
continue;
/*
* During scanning we found a volume which does not
* exist according to the information in the volume
* table. This must have happened due to an unclean
* reboot while the volume was being removed. Discard
* these eraseblocks.
*/
ubi_msg("finish volume %d removal", sv->vol_id);
ubi_scan_rm_volume(si, sv);
} else if (sv) {
err = check_sv(vol, sv);
if (err)
return err;
}
}
return 0;
}
/**
* ubi_read_volume_table - read volume table.
* information.
* @ubi: UBI device description object
* @si: scanning information
*
* This function reads volume table, checks it, recover from errors if needed,
* or creates it if needed. Returns zero in case of success and a negative
* error code in case of failure.
*/
int ubi_read_volume_table(struct ubi_device *ubi, struct ubi_scan_info *si)
{
int i, err;
struct ubi_scan_volume *sv;
empty_vtbl_record.crc = cpu_to_ubi32(0xf116c36b);
/*
* The number of supported volumes is limited by the eraseblock size
* and by the UBI_MAX_VOLUMES constant.
*/
ubi->vtbl_slots = ubi->leb_size / UBI_VTBL_RECORD_SIZE;
if (ubi->vtbl_slots > UBI_MAX_VOLUMES)
ubi->vtbl_slots = UBI_MAX_VOLUMES;
ubi->vtbl_size = ubi->vtbl_slots * UBI_VTBL_RECORD_SIZE;
ubi->vtbl_size = ALIGN(ubi->vtbl_size, ubi->min_io_size);
sv = ubi_scan_find_sv(si, UBI_LAYOUT_VOL_ID);
if (!sv) {
/*
* No logical eraseblocks belonging to the layout volume were
* found. This could mean that the flash is just empty. In
* this case we create empty layout volume.
*
* But if flash is not empty this must be a corruption or the
* MTD device just contains garbage.
*/
if (si->is_empty) {
ubi->vtbl = create_empty_lvol(ubi, si);
if (IS_ERR(ubi->vtbl))
return PTR_ERR(ubi->vtbl);
} else {
ubi_err("the layout volume was not found");
return -EINVAL;
}
} else {
if (sv->leb_count > UBI_LAYOUT_VOLUME_EBS) {
/* This must not happen with proper UBI images */
dbg_err("too many LEBs (%d) in layout volume",
sv->leb_count);
return -EINVAL;
}
ubi->vtbl = process_lvol(ubi, si, sv);
if (IS_ERR(ubi->vtbl))
return PTR_ERR(ubi->vtbl);
}
ubi->avail_pebs = ubi->good_peb_count;
/*
* The layout volume is OK, initialize the corresponding in-RAM data
* structures.
*/
err = init_volumes(ubi, si, ubi->vtbl);
if (err)
goto out_free;
/*
* Get sure that the scanning information is consistent to the
* information stored in the volume table.
*/
err = check_scanning_info(ubi, si);
if (err)
goto out_free;
return 0;
out_free:
kfree(ubi->vtbl);
for (i = 0; i < ubi->vtbl_slots + UBI_INT_VOL_COUNT; i++)
if (ubi->volumes[i]) {
kfree(ubi->volumes[i]);
ubi->volumes[i] = NULL;
}
return err;
}
#ifdef CONFIG_MTD_UBI_DEBUG_PARANOID
/**
* paranoid_vtbl_check - check volume table.
* @ubi: UBI device description object
*/
static void paranoid_vtbl_check(const struct ubi_device *ubi)
{
if (vtbl_check(ubi, ubi->vtbl)) {
ubi_err("paranoid check failed");
BUG();
}
}
#endif /* CONFIG_MTD_UBI_DEBUG_PARANOID */

1671
drivers/mtd/ubi/wl.c Normal file

File diff suppressed because it is too large Load Diff

202
include/linux/mtd/ubi.h Normal file
View File

@ -0,0 +1,202 @@
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*/
#ifndef __LINUX_UBI_H__
#define __LINUX_UBI_H__
#include <asm/ioctl.h>
#include <linux/types.h>
#include <mtd/ubi-user.h>
/*
* UBI data type hint constants.
*
* UBI_LONGTERM: long-term data
* UBI_SHORTTERM: short-term data
* UBI_UNKNOWN: data persistence is unknown
*
* These constants are used when data is written to UBI volumes in order to
* help the UBI wear-leveling unit to find more appropriate physical
* eraseblocks.
*/
enum {
UBI_LONGTERM = 1,
UBI_SHORTTERM,
UBI_UNKNOWN
};
/*
* enum ubi_open_mode - UBI volume open mode constants.
*
* UBI_READONLY: read-only mode
* UBI_READWRITE: read-write mode
* UBI_EXCLUSIVE: exclusive mode
*/
enum {
UBI_READONLY = 1,
UBI_READWRITE,
UBI_EXCLUSIVE
};
/**
* struct ubi_volume_info - UBI volume description data structure.
* @vol_id: volume ID
* @ubi_num: UBI device number this volume belongs to
* @size: how many physical eraseblocks are reserved for this volume
* @used_bytes: how many bytes of data this volume contains
* @used_ebs: how many physical eraseblocks of this volume actually contain any
* data
* @vol_type: volume type (%UBI_DYNAMIC_VOLUME or %UBI_STATIC_VOLUME)
* @corrupted: non-zero if the volume is corrupted (static volumes only)
* @upd_marker: non-zero if the volume has update marker set
* @alignment: volume alignment
* @usable_leb_size: how many bytes are available in logical eraseblocks of
* this volume
* @name_len: volume name length
* @name: volume name
* @cdev: UBI volume character device major and minor numbers
*
* The @corrupted flag is only relevant to static volumes and is always zero
* for dynamic ones. This is because UBI does not care about dynamic volume
* data protection and only cares about protecting static volume data.
*
* The @upd_marker flag is set if the volume update operation was interrupted.
* Before touching the volume data during the update operation, UBI first sets
* the update marker flag for this volume. If the volume update operation was
* further interrupted, the update marker indicates this. If the update marker
* is set, the contents of the volume is certainly damaged and a new volume
* update operation has to be started.
*
* To put it differently, @corrupted and @upd_marker fields have different
* semantics:
* o the @corrupted flag means that this static volume is corrupted for some
* reasons, but not because an interrupted volume update
* o the @upd_marker field means that the volume is damaged because of an
* interrupted update operation.
*
* I.e., the @corrupted flag is never set if the @upd_marker flag is set.
*
* The @used_bytes and @used_ebs fields are only really needed for static
* volumes and contain the number of bytes stored in this static volume and how
* many eraseblock this data occupies. In case of dynamic volumes, the
* @used_bytes field is equivalent to @size*@usable_leb_size, and the @used_ebs
* field is equivalent to @size.
*
* In general, logical eraseblock size is a property of the UBI device, not
* of the UBI volume. Indeed, the logical eraseblock size depends on the
* physical eraseblock size and on how much bytes UBI headers consume. But
* because of the volume alignment (@alignment), the usable size of logical
* eraseblocks if a volume may be less. The following equation is true:
* @usable_leb_size = LEB size - (LEB size mod @alignment),
* where LEB size is the logical eraseblock size defined by the UBI device.
*
* The alignment is multiple to the minimal flash input/output unit size or %1
* if all the available space is used.
*
* To put this differently, alignment may be considered is a way to change
* volume logical eraseblock sizes.
*/
struct ubi_volume_info {
int ubi_num;
int vol_id;
int size;
long long used_bytes;
int used_ebs;
int vol_type;
int corrupted;
int upd_marker;
int alignment;
int usable_leb_size;
int name_len;
const char *name;
dev_t cdev;
};
/**
* struct ubi_device_info - UBI device description data structure.
* @ubi_num: ubi device number
* @leb_size: logical eraseblock size on this UBI device
* @min_io_size: minimal I/O unit size
* @ro_mode: if this device is in read-only mode
* @cdev: UBI character device major and minor numbers
*
* Note, @leb_size is the logical eraseblock size offered by the UBI device.
* Volumes of this UBI device may have smaller logical eraseblock size if their
* alignment is not equivalent to %1.
*/
struct ubi_device_info {
int ubi_num;
int leb_size;
int min_io_size;
int ro_mode;
dev_t cdev;
};
/* UBI descriptor given to users when they open UBI volumes */
struct ubi_volume_desc;
int ubi_get_device_info(int ubi_num, struct ubi_device_info *di);
void ubi_get_volume_info(struct ubi_volume_desc *desc,
struct ubi_volume_info *vi);
struct ubi_volume_desc *ubi_open_volume(int ubi_num, int vol_id, int mode);
struct ubi_volume_desc *ubi_open_volume_nm(int ubi_num, const char *name,
int mode);
void ubi_close_volume(struct ubi_volume_desc *desc);
int ubi_leb_read(struct ubi_volume_desc *desc, int lnum, char *buf, int offset,
int len, int check);
int ubi_leb_write(struct ubi_volume_desc *desc, int lnum, const void *buf,
int offset, int len, int dtype);
int ubi_leb_change(struct ubi_volume_desc *desc, int lnum, const void *buf,
int len, int dtype);
int ubi_leb_erase(struct ubi_volume_desc *desc, int lnum);
int ubi_leb_unmap(struct ubi_volume_desc *desc, int lnum);
int ubi_is_mapped(struct ubi_volume_desc *desc, int lnum);
/*
* This function is the same as the 'ubi_leb_read()' function, but it does not
* provide the checking capability.
*/
static inline int ubi_read(struct ubi_volume_desc *desc, int lnum, char *buf,
int offset, int len)
{
return ubi_leb_read(desc, lnum, buf, offset, len, 0);
}
/*
* This function is the same as the 'ubi_leb_write()' functions, but it does
* not have the data type argument.
*/
static inline int ubi_write(struct ubi_volume_desc *desc, int lnum,
const void *buf, int offset, int len)
{
return ubi_leb_write(desc, lnum, buf, offset, len, UBI_UNKNOWN);
}
/*
* This function is the same as the 'ubi_leb_change()' functions, but it does
* not have the data type argument.
*/
static inline int ubi_change(struct ubi_volume_desc *desc, int lnum,
const void *buf, int len)
{
return ubi_leb_change(desc, lnum, buf, len, UBI_UNKNOWN);
}
#endif /* !__LINUX_UBI_H__ */

View File

@ -3,3 +3,5 @@ header-y += jffs2-user.h
header-y += mtd-abi.h
header-y += mtd-user.h
header-y += nftl-user.h
header-y += ubi-header.h
header-y += ubi-user.h

View File

@ -24,6 +24,7 @@ struct mtd_oob_buf {
#define MTD_NORFLASH 3
#define MTD_NANDFLASH 4
#define MTD_DATAFLASH 6
#define MTD_UBIVOLUME 7
#define MTD_WRITEABLE 0x400 /* Device is writeable */
#define MTD_BIT_WRITEABLE 0x800 /* Single bits can be flipped */

360
include/mtd/ubi-header.h Normal file
View File

@ -0,0 +1,360 @@
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Authors: Artem Bityutskiy (Битюцкий Артём)
* Thomas Gleixner
* Frank Haverkamp
* Oliver Lohmann
* Andreas Arnez
*/
/*
* This file defines the layout of UBI headers and all the other UBI on-flash
* data structures. May be included by user-space.
*/
#ifndef __UBI_HEADER_H__
#define __UBI_HEADER_H__
#include <asm/byteorder.h>
/* The version of UBI images supported by this implementation */
#define UBI_VERSION 1
/* The highest erase counter value supported by this implementation */
#define UBI_MAX_ERASECOUNTER 0x7FFFFFFF
/* The initial CRC32 value used when calculating CRC checksums */
#define UBI_CRC32_INIT 0xFFFFFFFFU
/* Erase counter header magic number (ASCII "UBI#") */
#define UBI_EC_HDR_MAGIC 0x55424923
/* Volume identifier header magic number (ASCII "UBI!") */
#define UBI_VID_HDR_MAGIC 0x55424921
/*
* Volume type constants used in the volume identifier header.
*
* @UBI_VID_DYNAMIC: dynamic volume
* @UBI_VID_STATIC: static volume
*/
enum {
UBI_VID_DYNAMIC = 1,
UBI_VID_STATIC = 2
};
/*
* Compatibility constants used by internal volumes.
*
* @UBI_COMPAT_DELETE: delete this internal volume before anything is written
* to the flash
* @UBI_COMPAT_RO: attach this device in read-only mode
* @UBI_COMPAT_PRESERVE: preserve this internal volume - do not touch its
* physical eraseblocks, don't allow the wear-leveling unit to move them
* @UBI_COMPAT_REJECT: reject this UBI image
*/
enum {
UBI_COMPAT_DELETE = 1,
UBI_COMPAT_RO = 2,
UBI_COMPAT_PRESERVE = 4,
UBI_COMPAT_REJECT = 5
};
/*
* ubi16_t/ubi32_t/ubi64_t - 16, 32, and 64-bit integers used in UBI on-flash
* data structures.
*/
typedef struct {
uint16_t int16;
} __attribute__ ((packed)) ubi16_t;
typedef struct {
uint32_t int32;
} __attribute__ ((packed)) ubi32_t;
typedef struct {
uint64_t int64;
} __attribute__ ((packed)) ubi64_t;
/*
* In this implementation of UBI uses the big-endian format for on-flash
* integers. The below are the corresponding conversion macros.
*/
#define cpu_to_ubi16(x) ((ubi16_t){__cpu_to_be16(x)})
#define ubi16_to_cpu(x) ((uint16_t)__be16_to_cpu((x).int16))
#define cpu_to_ubi32(x) ((ubi32_t){__cpu_to_be32(x)})
#define ubi32_to_cpu(x) ((uint32_t)__be32_to_cpu((x).int32))
#define cpu_to_ubi64(x) ((ubi64_t){__cpu_to_be64(x)})
#define ubi64_to_cpu(x) ((uint64_t)__be64_to_cpu((x).int64))
/* Sizes of UBI headers */
#define UBI_EC_HDR_SIZE sizeof(struct ubi_ec_hdr)
#define UBI_VID_HDR_SIZE sizeof(struct ubi_vid_hdr)
/* Sizes of UBI headers without the ending CRC */
#define UBI_EC_HDR_SIZE_CRC (UBI_EC_HDR_SIZE - sizeof(ubi32_t))
#define UBI_VID_HDR_SIZE_CRC (UBI_VID_HDR_SIZE - sizeof(ubi32_t))
/**
* struct ubi_ec_hdr - UBI erase counter header.
* @magic: erase counter header magic number (%UBI_EC_HDR_MAGIC)
* @version: version of UBI implementation which is supposed to accept this
* UBI image
* @padding1: reserved for future, zeroes
* @ec: the erase counter
* @vid_hdr_offset: where the VID header starts
* @data_offset: where the user data start
* @padding2: reserved for future, zeroes
* @hdr_crc: erase counter header CRC checksum
*
* The erase counter header takes 64 bytes and has a plenty of unused space for
* future usage. The unused fields are zeroed. The @version field is used to
* indicate the version of UBI implementation which is supposed to be able to
* work with this UBI image. If @version is greater then the current UBI
* version, the image is rejected. This may be useful in future if something
* is changed radically. This field is duplicated in the volume identifier
* header.
*
* The @vid_hdr_offset and @data_offset fields contain the offset of the the
* volume identifier header and user data, relative to the beginning of the
* physical eraseblock. These values have to be the same for all physical
* eraseblocks.
*/
struct ubi_ec_hdr {
ubi32_t magic;
uint8_t version;
uint8_t padding1[3];
ubi64_t ec; /* Warning: the current limit is 31-bit anyway! */
ubi32_t vid_hdr_offset;
ubi32_t data_offset;
uint8_t padding2[36];
ubi32_t hdr_crc;
} __attribute__ ((packed));
/**
* struct ubi_vid_hdr - on-flash UBI volume identifier header.
* @magic: volume identifier header magic number (%UBI_VID_HDR_MAGIC)
* @version: UBI implementation version which is supposed to accept this UBI
* image (%UBI_VERSION)
* @vol_type: volume type (%UBI_VID_DYNAMIC or %UBI_VID_STATIC)
* @copy_flag: if this logical eraseblock was copied from another physical
* eraseblock (for wear-leveling reasons)
* @compat: compatibility of this volume (%0, %UBI_COMPAT_DELETE,
* %UBI_COMPAT_IGNORE, %UBI_COMPAT_PRESERVE, or %UBI_COMPAT_REJECT)
* @vol_id: ID of this volume
* @lnum: logical eraseblock number
* @leb_ver: version of this logical eraseblock (IMPORTANT: obsolete, to be
* removed, kept only for not breaking older UBI users)
* @data_size: how many bytes of data this logical eraseblock contains
* @used_ebs: total number of used logical eraseblocks in this volume
* @data_pad: how many bytes at the end of this physical eraseblock are not
* used
* @data_crc: CRC checksum of the data stored in this logical eraseblock
* @padding1: reserved for future, zeroes
* @sqnum: sequence number
* @padding2: reserved for future, zeroes
* @hdr_crc: volume identifier header CRC checksum
*
* The @sqnum is the value of the global sequence counter at the time when this
* VID header was created. The global sequence counter is incremented each time
* UBI writes a new VID header to the flash, i.e. when it maps a logical
* eraseblock to a new physical eraseblock. The global sequence counter is an
* unsigned 64-bit integer and we assume it never overflows. The @sqnum
* (sequence number) is used to distinguish between older and newer versions of
* logical eraseblocks.
*
* There are 2 situations when there may be more then one physical eraseblock
* corresponding to the same logical eraseblock, i.e., having the same @vol_id
* and @lnum values in the volume identifier header. Suppose we have a logical
* eraseblock L and it is mapped to the physical eraseblock P.
*
* 1. Because UBI may erase physical eraseblocks asynchronously, the following
* situation is possible: L is asynchronously erased, so P is scheduled for
* erasure, then L is written to,i.e. mapped to another physical eraseblock P1,
* so P1 is written to, then an unclean reboot happens. Result - there are 2
* physical eraseblocks P and P1 corresponding to the same logical eraseblock
* L. But P1 has greater sequence number, so UBI picks P1 when it attaches the
* flash.
*
* 2. From time to time UBI moves logical eraseblocks to other physical
* eraseblocks for wear-leveling reasons. If, for example, UBI moves L from P
* to P1, and an unclean reboot happens before P is physically erased, there
* are two physical eraseblocks P and P1 corresponding to L and UBI has to
* select one of them when the flash is attached. The @sqnum field says which
* PEB is the original (obviously P will have lower @sqnum) and the copy. But
* it is not enough to select the physical eraseblock with the higher sequence
* number, because the unclean reboot could have happen in the middle of the
* copying process, so the data in P is corrupted. It is also not enough to
* just select the physical eraseblock with lower sequence number, because the
* data there may be old (consider a case if more data was added to P1 after
* the copying). Moreover, the unclean reboot may happen when the erasure of P
* was just started, so it result in unstable P, which is "mostly" OK, but
* still has unstable bits.
*
* UBI uses the @copy_flag field to indicate that this logical eraseblock is a
* copy. UBI also calculates data CRC when the data is moved and stores it at
* the @data_crc field of the copy (P1). So when UBI needs to pick one physical
* eraseblock of two (P or P1), the @copy_flag of the newer one (P1) is
* examined. If it is cleared, the situation* is simple and the newer one is
* picked. If it is set, the data CRC of the copy (P1) is examined. If the CRC
* checksum is correct, this physical eraseblock is selected (P1). Otherwise
* the older one (P) is selected.
*
* Note, there is an obsolete @leb_ver field which was used instead of @sqnum
* in the past. But it is not used anymore and we keep it in order to be able
* to deal with old UBI images. It will be removed at some point.
*
* There are 2 sorts of volumes in UBI: user volumes and internal volumes.
* Internal volumes are not seen from outside and are used for various internal
* UBI purposes. In this implementation there is only one internal volume - the
* layout volume. Internal volumes are the main mechanism of UBI extensions.
* For example, in future one may introduce a journal internal volume. Internal
* volumes have their own reserved range of IDs.
*
* The @compat field is only used for internal volumes and contains the "degree
* of their compatibility". It is always zero for user volumes. This field
* provides a mechanism to introduce UBI extensions and to be still compatible
* with older UBI binaries. For example, if someone introduced a journal in
* future, he would probably use %UBI_COMPAT_DELETE compatibility for the
* journal volume. And in this case, older UBI binaries, which know nothing
* about the journal volume, would just delete this volume and work perfectly
* fine. This is similar to what Ext2fs does when it is fed by an Ext3fs image
* - it just ignores the Ext3fs journal.
*
* The @data_crc field contains the CRC checksum of the contents of the logical
* eraseblock if this is a static volume. In case of dynamic volumes, it does
* not contain the CRC checksum as a rule. The only exception is when the
* data of the physical eraseblock was moved by the wear-leveling unit, then
* the wear-leveling unit calculates the data CRC and stores it in the
* @data_crc field. And of course, the @copy_flag is %in this case.
*
* The @data_size field is used only for static volumes because UBI has to know
* how many bytes of data are stored in this eraseblock. For dynamic volumes,
* this field usually contains zero. The only exception is when the data of the
* physical eraseblock was moved to another physical eraseblock for
* wear-leveling reasons. In this case, UBI calculates CRC checksum of the
* contents and uses both @data_crc and @data_size fields. In this case, the
* @data_size field contains data size.
*
* The @used_ebs field is used only for static volumes and indicates how many
* eraseblocks the data of the volume takes. For dynamic volumes this field is
* not used and always contains zero.
*
* The @data_pad is calculated when volumes are created using the alignment
* parameter. So, effectively, the @data_pad field reduces the size of logical
* eraseblocks of this volume. This is very handy when one uses block-oriented
* software (say, cramfs) on top of the UBI volume.
*/
struct ubi_vid_hdr {
ubi32_t magic;
uint8_t version;
uint8_t vol_type;
uint8_t copy_flag;
uint8_t compat;
ubi32_t vol_id;
ubi32_t lnum;
ubi32_t leb_ver; /* obsolete, to be removed, don't use */
ubi32_t data_size;
ubi32_t used_ebs;
ubi32_t data_pad;
ubi32_t data_crc;
uint8_t padding1[4];
ubi64_t sqnum;
uint8_t padding2[12];
ubi32_t hdr_crc;
} __attribute__ ((packed));
/* Internal UBI volumes count */
#define UBI_INT_VOL_COUNT 1
/*
* Starting ID of internal volumes. There is reserved room for 4096 internal
* volumes.
*/
#define UBI_INTERNAL_VOL_START (0x7FFFFFFF - 4096)
/* The layout volume contains the volume table */
#define UBI_LAYOUT_VOL_ID UBI_INTERNAL_VOL_START
#define UBI_LAYOUT_VOLUME_EBS 2
#define UBI_LAYOUT_VOLUME_NAME "layout volume"
#define UBI_LAYOUT_VOLUME_COMPAT UBI_COMPAT_REJECT
/* The maximum number of volumes per one UBI device */
#define UBI_MAX_VOLUMES 128
/* The maximum volume name length */
#define UBI_VOL_NAME_MAX 127
/* Size of the volume table record */
#define UBI_VTBL_RECORD_SIZE sizeof(struct ubi_vtbl_record)
/* Size of the volume table record without the ending CRC */
#define UBI_VTBL_RECORD_SIZE_CRC (UBI_VTBL_RECORD_SIZE - sizeof(ubi32_t))
/**
* struct ubi_vtbl_record - a record in the volume table.
* @reserved_pebs: how many physical eraseblocks are reserved for this volume
* @alignment: volume alignment
* @data_pad: how many bytes are unused at the end of the each physical
* eraseblock to satisfy the requested alignment
* @vol_type: volume type (%UBI_DYNAMIC_VOLUME or %UBI_STATIC_VOLUME)
* @upd_marker: if volume update was started but not finished
* @name_len: volume name length
* @name: the volume name
* @padding2: reserved, zeroes
* @crc: a CRC32 checksum of the record
*
* The volume table records are stored in the volume table, which is stored in
* the layout volume. The layout volume consists of 2 logical eraseblock, each
* of which contains a copy of the volume table (i.e., the volume table is
* duplicated). The volume table is an array of &struct ubi_vtbl_record
* objects indexed by the volume ID.
*
* If the size of the logical eraseblock is large enough to fit
* %UBI_MAX_VOLUMES records, the volume table contains %UBI_MAX_VOLUMES
* records. Otherwise, it contains as many records as it can fit (i.e., size of
* logical eraseblock divided by sizeof(struct ubi_vtbl_record)).
*
* The @upd_marker flag is used to implement volume update. It is set to %1
* before update and set to %0 after the update. So if the update operation was
* interrupted, UBI knows that the volume is corrupted.
*
* The @alignment field is specified when the volume is created and cannot be
* later changed. It may be useful, for example, when a block-oriented file
* system works on top of UBI. The @data_pad field is calculated using the
* logical eraseblock size and @alignment. The alignment must be multiple to the
* minimal flash I/O unit. If @alignment is 1, all the available space of
* the physical eraseblocks is used.
*
* Empty records contain all zeroes and the CRC checksum of those zeroes.
*/
struct ubi_vtbl_record {
ubi32_t reserved_pebs;
ubi32_t alignment;
ubi32_t data_pad;
uint8_t vol_type;
uint8_t upd_marker;
ubi16_t name_len;
uint8_t name[UBI_VOL_NAME_MAX+1];
uint8_t padding2[24];
ubi32_t crc;
} __attribute__ ((packed));
#endif /* !__UBI_HEADER_H__ */

161
include/mtd/ubi-user.h Normal file
View File

@ -0,0 +1,161 @@
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*/
#ifndef __UBI_USER_H__
#define __UBI_USER_H__
/*
* UBI volume creation
* ~~~~~~~~~~~~~~~~~~~
*
* UBI volumes are created via the %UBI_IOCMKVOL IOCTL command of UBI character
* device. A &struct ubi_mkvol_req object has to be properly filled and a
* pointer to it has to be passed to the IOCTL.
*
* UBI volume deletion
* ~~~~~~~~~~~~~~~~~~~
*
* To delete a volume, the %UBI_IOCRMVOL IOCTL command of the UBI character
* device should be used. A pointer to the 32-bit volume ID hast to be passed
* to the IOCTL.
*
* UBI volume re-size
* ~~~~~~~~~~~~~~~~~~
*
* To re-size a volume, the %UBI_IOCRSVOL IOCTL command of the UBI character
* device should be used. A &struct ubi_rsvol_req object has to be properly
* filled and a pointer to it has to be passed to the IOCTL.
*
* UBI volume update
* ~~~~~~~~~~~~~~~~~
*
* Volume update should be done via the %UBI_IOCVOLUP IOCTL command of the
* corresponding UBI volume character device. A pointer to a 64-bit update
* size should be passed to the IOCTL. After then, UBI expects user to write
* this number of bytes to the volume character device. The update is finished
* when the claimed number of bytes is passed. So, the volume update sequence
* is something like:
*
* fd = open("/dev/my_volume");
* ioctl(fd, UBI_IOCVOLUP, &image_size);
* write(fd, buf, image_size);
* close(fd);
*/
/*
* When a new volume is created, users may either specify the volume number they
* want to create or to let UBI automatically assign a volume number using this
* constant.
*/
#define UBI_VOL_NUM_AUTO (-1)
/* Maximum volume name length */
#define UBI_MAX_VOLUME_NAME 127
/* IOCTL commands of UBI character devices */
#define UBI_IOC_MAGIC 'o'
/* Create an UBI volume */
#define UBI_IOCMKVOL _IOW(UBI_IOC_MAGIC, 0, struct ubi_mkvol_req)
/* Remove an UBI volume */
#define UBI_IOCRMVOL _IOW(UBI_IOC_MAGIC, 1, int32_t)
/* Re-size an UBI volume */
#define UBI_IOCRSVOL _IOW(UBI_IOC_MAGIC, 2, struct ubi_rsvol_req)
/* IOCTL commands of UBI volume character devices */
#define UBI_VOL_IOC_MAGIC 'O'
/* Start UBI volume update */
#define UBI_IOCVOLUP _IOW(UBI_VOL_IOC_MAGIC, 0, int64_t)
/* An eraseblock erasure command, used for debugging, disabled by default */
#define UBI_IOCEBER _IOW(UBI_VOL_IOC_MAGIC, 1, int32_t)
/*
* UBI volume type constants.
*
* @UBI_DYNAMIC_VOLUME: dynamic volume
* @UBI_STATIC_VOLUME: static volume
*/
enum {
UBI_DYNAMIC_VOLUME = 3,
UBI_STATIC_VOLUME = 4
};
/**
* struct ubi_mkvol_req - volume description data structure used in
* volume creation requests.
* @vol_id: volume number
* @alignment: volume alignment
* @bytes: volume size in bytes
* @vol_type: volume type (%UBI_DYNAMIC_VOLUME or %UBI_STATIC_VOLUME)
* @padding1: reserved for future, not used
* @name_len: volume name length
* @padding2: reserved for future, not used
* @name: volume name
*
* This structure is used by userspace programs when creating new volumes. The
* @used_bytes field is only necessary when creating static volumes.
*
* The @alignment field specifies the required alignment of the volume logical
* eraseblock. This means, that the size of logical eraseblocks will be aligned
* to this number, i.e.,
* (UBI device logical eraseblock size) mod (@alignment) = 0.
*
* To put it differently, the logical eraseblock of this volume may be slightly
* shortened in order to make it properly aligned. The alignment has to be
* multiple of the flash minimal input/output unit, or %1 to utilize the entire
* available space of logical eraseblocks.
*
* The @alignment field may be useful, for example, when one wants to maintain
* a block device on top of an UBI volume. In this case, it is desirable to fit
* an integer number of blocks in logical eraseblocks of this UBI volume. With
* alignment it is possible to update this volume using plane UBI volume image
* BLOBs, without caring about how to properly align them.
*/
struct ubi_mkvol_req {
int32_t vol_id;
int32_t alignment;
int64_t bytes;
int8_t vol_type;
int8_t padding1;
int16_t name_len;
int8_t padding2[4];
char name[UBI_MAX_VOLUME_NAME+1];
} __attribute__ ((packed));
/**
* struct ubi_rsvol_req - a data structure used in volume re-size requests.
* @vol_id: ID of the volume to re-size
* @bytes: new size of the volume in bytes
*
* Re-sizing is possible for both dynamic and static volumes. But while dynamic
* volumes may be re-sized arbitrarily, static volumes cannot be made to be
* smaller then the number of bytes they bear. To arbitrarily shrink a static
* volume, it must be wiped out first (by means of volume update operation with
* zero number of bytes).
*/
struct ubi_rsvol_req {
int64_t bytes;
int32_t vol_id;
} __attribute__ ((packed));
#endif /* __UBI_USER_H__ */