mmc: mmci: avoid clearing ST Micro busy end interrupt mistakenly

This fixes a race condition that may occur whenever ST micro busy end
interrupt is raised just after being unmasked but before leaving mmci
interrupt context.

A dead-lock has been found if connecting mmci ST Micro variant whose amba
id is 0x10480180 to some new eMMC that supports internal caches.  Whenever
mmci driver enables cache control by programming eMMC's EXT_CSD register,
block driver may request to flush the eMMC internal caches causing mmci
driver to send a MMC_SWITCH command to the card with FLUSH_CACHE operation.
And because busy end interrupt may be mistakenly cleared while not yet
processed, this mmc request may never complete.  As a result, mmcqd task
may be stuck forever.

Here is an instance caught by lockup detector which shows that mmcqd task
was hung while waiting for mmc_flush_cache command to complete:

..
[  240.251595] INFO: task mmcqd/1:52 blocked for more than 120 seconds.
[  240.257973]       Not tainted 4.1.13-00510-g9d91424 #2
[  240.263109] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  240.270955] mmcqd/1         D c047504c     0    52      2 0x00000000
[  240.277359] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[  240.284418] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[  240.292191] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[  240.300491] [<c0476040>] (wait_for_common) from [<c02efc1c>] (mmc_wait_for_req_done+0x4c/0x13c)
[  240.309224] [<c02efc1c>] (mmc_wait_for_req_done) from [<c02efd90>] (mmc_wait_for_cmd+0x64/0x84)
[  240.317953] [<c02efd90>] (mmc_wait_for_cmd) from [<c02f5b14>] (__mmc_switch+0xa4/0x2a8)
[  240.325964] [<c02f5b14>] (__mmc_switch) from [<c02f5d40>] (mmc_switch+0x28/0x30)
[  240.333389] [<c02f5d40>] (mmc_switch) from [<c02f0984>] (mmc_flush_cache+0x54/0x80)
[  240.341073] [<c02f0984>] (mmc_flush_cache) from [<c02ff0c4>] (mmc_blk_issue_rq+0x114/0x4e8)
[  240.349459] [<c02ff0c4>] (mmc_blk_issue_rq) from [<c03008d4>] (mmc_queue_thread+0xc0/0x180)
[  240.357844] [<c03008d4>] (mmc_queue_thread) from [<c003cf90>] (kthread+0xdc/0xf4)
[  240.365339] [<c003cf90>] (kthread) from [<c0010068>] (ret_from_fork+0x14/0x2c)
..
..
[  240.664311] INFO: task partprobe:564 blocked for more than 120 seconds.
[  240.670943]       Not tainted 4.1.13-00510-g9d91424 #2
[  240.676078] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  240.683922] partprobe       D c047504c     0   564    486 0x00000000
[  240.690318] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[  240.697396] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[  240.705149] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[  240.713446] [<c0476040>] (wait_for_common) from [<c01f3300>] (submit_bio_wait+0x58/0x64)
[  240.721571] [<c01f3300>] (submit_bio_wait) from [<c01fbbd8>] (blkdev_issue_flush+0x60/0x88)
[  240.729957] [<c01fbbd8>] (blkdev_issue_flush) from [<c010ff84>] (blkdev_fsync+0x34/0x44)
[  240.738083] [<c010ff84>] (blkdev_fsync) from [<c0109594>] (do_fsync+0x3c/0x64)
[  240.745319] [<c0109594>] (do_fsync) from [<c000ffc0>] (ret_fast_syscall+0x0/0x3c)
..

Here is the detailed sequence showing when this issue may happen:

1) At probe time, mmci device is initialized and card busy detection based
on DAT[0] monitoring is enabled.

2) Later during run time, since card reported to support internal caches, a
MMCI_SWITCH command is sent to eMMC device with FLUSH_CACHE operation. On
receiving this command, eMMC may enter busy state (for a relatively short
time in the case of the dead-lock).

3) Then mmci interrupt is raised and mmci_irq() is called:

MMCISTATUS register is read and is equal to 0x01000440. So the following
status bits are set:
- MCI_CMDRESPEND (= 6)
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)

Since MMCIMASK0 register is 0x3FF, status variable is set to 0x00000040 and
BIT MCI_CMDRESPEND is cleared by writing MMCICLEAR register.

Then mmci_cmd_irq() is called. Considering the following conditions:
- host->busy_status is 0,
- this is a "busy response",
- reading again MMCISTATUS register gives 0x1000400,
MMCIMASK0 is updated to unmask MCI_ST_BUSYEND bit.

Thus, MMCIMASK0 is set to 0x010003FF and host->busy_status is set to wait
for busy end completion.

Back again in status loop of mmci_irq(), we quickly go through
mmci_data_irq() as there are no data in that case.  And we finally go
through following test at the end of while(status) loop:

/*
 * Don't poll for busy completion in irq context.
 */
if (host->variant->busy_detect && host->busy_status)
	status &= ~host->variant->busy_detect_flag;

Because status variable is not yet null (is equal to 0x40), we do not leave
interrupt context yet but we loop again into while(status) loop. So we run
across following steps:

a) MMCISTATUS register is read again and this time is equal to 0x01000400.
So that following bits are set:
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)

Since MMCIMASK0 register is equal to 0x010003FF:

b) status variable is set to 0x01000000.
c) MCI_ST_CARDBUSY bit is cleared by writing MMCICLEAR register.

Then, mmci_cmd_irq() is called one more time. Since host->busy_status is
set and that MCI_ST_CARDBUSY is set in status variable, we just return from
this function.

Back again in mmci_irq(), status variable is set to 0 and we finally leave
the while(status) loop. As a result we leave interrupt context, waiting for
busy end interrupt event.

Now, consider that busy end completion is raised IN BETWEEN steps 3.a) and
3.c). In such a case, we may mistakenly clear busy end interrupt at step
3.c) while it has not yet been processed. This will result in mmc command
to wait forever for a busy end completion that will never happen.

To fix the problem, this patch implements the following changes:

Considering that the mmci seems to be triggering the IRQ on both edges
while monitoring DAT0 for busy completion and that same status bit is used
to monitor start and end of busy detection, special care must be taken to
make sure that both start and end interrupts are always cleared one after
the other.

1) Clearing of card busy bit is moved in mmc_cmd_irq() function where
unmasking of busy end bit is effectively handled.
2) Just before unmasking busy end event, busy start event is cleared by
writing card busy bit in MMCICLEAR register.
3) Finally, once we are no more busy with a command, busy end event is
cleared writing again card busy bit in MMCICLEAR register.

This patch has been tested with the ST Accordo5 machine, not yet supported
upstream but relies on the mmci driver.

Signed-off-by: Sarang Mairal <sarang.mairal@garmin.com>
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

drivers/mmc/host/mmci.c

@@ -1023,7 +1023,12 @@ mmci_cmd_irq(struct mmci_host *host, struct mmc_command *cmd,
 		if (!host->busy_status && busy_resp &&
 		    !(status & (MCI_CMDCRCFAIL|MCI_CMDTIMEOUT)) &&
 		    (readl(base + MMCISTATUS) & host->variant->busy_detect_flag)) {
-			/* Unmask the busy IRQ */
+
+			/* Clear the busy start IRQ */
+			writel(host->variant->busy_detect_mask,
+			       host->base + MMCICLEAR);
+
+			/* Unmask the busy end IRQ */
 			writel(readl(base + MMCIMASK0) |
 			       host->variant->busy_detect_mask,
 			       base + MMCIMASK0);
@@ -1038,10 +1043,14 @@ mmci_cmd_irq(struct mmci_host *host, struct mmc_command *cmd,
 
 		/*
 		 * At this point we are not busy with a command, we have
-		 * not received a new busy request, mask the busy IRQ and
-		 * fall through to process the IRQ.
+		 * not received a new busy request, clear and mask the busy
+		 * end IRQ and fall through to process the IRQ.
 		 */
 		if (host->busy_status) {
+
+			writel(host->variant->busy_detect_mask,
+			       host->base + MMCICLEAR);
+
 			writel(readl(base + MMCIMASK0) &
 			       ~host->variant->busy_detect_mask,
 			       base + MMCIMASK0);
@@ -1283,12 +1292,21 @@ static irqreturn_t mmci_irq(int irq, void *dev_id)
 		}
 
 		/*
-		 * We intentionally clear the MCI_ST_CARDBUSY IRQ here (if it's
-		 * enabled) since the HW seems to be triggering the IRQ on both
-		 * edges while monitoring DAT0 for busy completion.
+		 * We intentionally clear the MCI_ST_CARDBUSY IRQ (if it's
+		 * enabled) in mmci_cmd_irq() function where ST Micro busy
+		 * detection variant is handled. Considering the HW seems to be
+		 * triggering the IRQ on both edges while monitoring DAT0 for
+		 * busy completion and that same status bit is used to monitor
+		 * start and end of busy detection, special care must be taken
+		 * to make sure that both start and end interrupts are always
+		 * cleared one after the other.
 		 */
 		status &= readl(host->base + MMCIMASK0);
-		writel(status, host->base + MMCICLEAR);
+		if (host->variant->busy_detect)
+			writel(status & ~host->variant->busy_detect_mask,
+			       host->base + MMCICLEAR);
+		else
+			writel(status, host->base + MMCICLEAR);
 
 		dev_dbg(mmc_dev(host->mmc), "irq0 (data+cmd) %08x\n", status);