renegade-project/linux-next
2
0
Fork 0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-28 15:13:55 +08:00
Code

[media] drxk: Add support for parallel mode and prints mpeg mode

Browse Source 
While the driver has support for both serial and parallel mode,
There's was way to select serial mode via configuration. Add
a config option for that, while keeping the default in serial mode.

Also, at debug mode, it will now print a message when mpeg is
enabled/disabled, and showing if parallel or serial mode were
selected, helping developers to double-check if the DRX-K is at
the right mode.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This commit is contained in:
Mauro Carvalho Chehab 2011-07-24 14:59:20 -03:00
parent 0d3e6fe7cb
commit 534e048103
2 changed files with 11 additions and 6 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

3
drivers/media/dvb/frontends/drxk.h
View File

@ -8,6 +8,8 @@
* struct drxk_config - Configure the initial parameters for DRX-K
*
* adr: I2C Address of the DRX-K
* parallel_ts: true means that the device uses parallel TS,
* Serial otherwise.
* single_master: Device is on the single master mode
* no_i2c_bridge: Don't switch the I2C bridge to talk with tuner
* antenna_gpio: GPIO bit used to control the antenna
@ -22,6 +24,7 @@ struct drxk_config {
u8 adr;
bool single_master;
bool no_i2c_bridge;
bool parallel_ts;
bool antenna_dvbt;
u16 antenna_gpio;

14
drivers/media/dvb/frontends/drxk_hard.c
View File

@ -660,7 +660,6 @@ static int init_state(struct drxk_state *state)
/* io_pad_cfg_mode output mode is drive always */
/* io_pad_cfg_drive is set to power 2 (23 mA) */
u32 ulGPIOCfg = 0x0113;
u32 ulSerialMode = 1;
u32 ulInvertTSClock = 0;
u32 ulTSDataStrength = DRXK_MPEG_SERIAL_OUTPUT_PIN_DRIVE_STRENGTH;
u32 ulTSClockkStrength = DRXK_MPEG_OUTPUT_CLK_DRIVE_STRENGTH;
@ -811,8 +810,6 @@ static int init_state(struct drxk_state *state)
/* MPEG output configuration */
state->m_enableMPEGOutput = true; /* If TRUE; enable MPEG ouput */
state->m_insertRSByte = false; /* If TRUE; insert RS byte */
state->m_enableParallel = true; /* If TRUE;
parallel out otherwise serial */
state->m_invertDATA = false; /* If TRUE; invert DATA signals */
state->m_invertERR = false; /* If TRUE; invert ERR signal */
state->m_invertSTR = false; /* If TRUE; invert STR signals */
@ -857,8 +854,6 @@ static int init_state(struct drxk_state *state)
state->m_bPowerDown = false;
state->m_currentPowerMode = DRX_POWER_DOWN;
state->m_enableParallel = (ulSerialMode == 0);
state->m_rfmirror = (ulRfMirror == 0);
state->m_IfAgcPol = false;
return 0;
@ -1195,7 +1190,9 @@ static int MPEGTSConfigurePins(struct drxk_state *state, bool mpegEnable)
u16 sioPdrMclkCfg = 0;
u16 sioPdrMdxCfg = 0;
dprintk(1, "\n");
dprintk(1, ": mpeg %s, %s mode\n",
mpegEnable ? "enable" : "disable",
state->m_enableParallel ? "parallel" : "serial");
/* stop lock indicator process */
status = write16(state, SCU_RAM_GPIO__A, SCU_RAM_GPIO_HW_LOCK_IND_DISABLE);
@ -6432,6 +6429,11 @@ struct dvb_frontend *drxk_attach(const struct drxk_config *config,
state->antenna_dvbt = config->antenna_dvbt;
state->m_ChunkSize = config->chunk_size;
if (config->parallel_ts)
state->m_enableParallel = true;
else
state->m_enableParallel = false;
/* NOTE: as more UIO bits will be used, add them to the mask */
state->UIO_mask = config->antenna_gpio;