renegade-project/linux-next
2
0
Fork 0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-28 07:04:00 +08:00
Code
ace30f74ac
linux-next/drivers/pci/pcie/Makefile

14 lines
286 B
Makefile
Raw Normal View History

Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
#
# Makefile for PCI-Express PORT Driver
#
PCI: add PCI Express ASPM support PCI Express ASPM defines a protocol for PCI Express components in the D0 state to reduce Link power by placing their Links into a low power state and instructing the other end of the Link to do likewise. This capability allows hardware-autonomous, dynamic Link power reduction beyond what is achievable by software-only controlled power management. However, The device should be configured by software appropriately. Enabling ASPM will save power, but will introduce device latency. This patch adds ASPM support in Linux. It introduces a global policy for ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control it. The interface can be used as a boot option too. Currently we have below setting: -default, BIOS default setting -powersave, highest power saving mode, enable all available ASPM state and clock power management -performance, highest performance, disable ASPM and clock power management By default, the 'default' policy is used currently. In my test, power difference between powersave mode and performance mode is about 1.3w in a system with 3 PCIE links. Note: some devices might not work well with aspm, either because chipset issue or device issue. The patch provide API (pci_disable_link_state), driver can disable ASPM for specific device. Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-25 09:46:41 +08:00
# Build PCI Express ASPM if needed
obj-$(CONFIG_PCIEASPM) += aspm.o
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
pcieportdrv-y := portdrv_core.o portdrv_pci.o portdrv_bus.o
obj-$(CONFIG_PCIEPORTBUS) += pcieportdrv.o
PCI-Express AER implemetation: AER core and aerdriver Patch 3 implements the core part of PCI-Express AER and aerdrv port service driver. When a root port service device is probed, the aerdrv will call request_irq to register irq handler for AER error interrupt. When a device sends an PCI-Express error message to the root port, the root port will trigger an interrupt, by either MSI or IO-APIC, then kernel would run the irq handler. The handler collects root error status register and schedules a work. The work will call the core part to process the error based on its type (Correctable/non-fatal/fatal). As for Correctable errors, the patch chooses to just clear the correctable error status register of the device. As for the non-fatal error, the patch follows generic PCI error handler rules to call the error callback functions of the endpoint's driver. If the device is a bridge, the patch chooses to broadcast the error to downstream devices. As for the fatal error, the patch resets the pci-express link and follows generic PCI error handler rules to call the error callback functions of the endpoint's driver. If the device is a bridge, the patch chooses to broadcast the error to downstream devices. Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-07-31 15:21:33 +08:00
# Build PCI Express AER if needed
obj-$(CONFIG_PCIEAER) += aer/
Copy Permalink